Anatomy of Process Research and Development - ACS Publications

year and involve about 20 to 80 healthy volunteers. The tests study ..... a massive research program or it might be ideal to produce several compounds...
0 downloads 0 Views 2MB Size
Chapter 1

Anatomy of Process Research and Development Nikolaos H. Petousis

Downloaded by 117.255.209.72 on March 5, 2016 | http://pubs.acs.org Publication Date: April 19, 2002 | doi: 10.1021/bk-2002-0817.ch001

Corporate Development, Ricera, LLC, 7528 Auburn Road, Concord, OH 44077 ([email protected])

I.

Introduction

In this report we would like to discuss the importance of process development in the pharmaceutical industry. Superior process development can reduce manufacturing cost, but the power of process development more often lies in how it helps companies achieve a competitive advantage. Consolidation and increased competition in the pharmaceutical industry means that companies are under increased pressure to produce more drugs and to get them to market quicker then ever before. To meet this challenge and gain a competitive edge, most major drug companies are aggressively looking to streamline process development. The benefits of reducing development time are well known. In some cases, short delays in product introduction could be deadly. Perhaps no issue has drawn more attention in recent years than the importance of bringing new products to market faster. Every pharmaceutical manufacturer is only too aware of the rising cost to bringing a drug to market. Indeed, the process of getting a novel drug to market is now estimated to cost the manufacturer more than $500 million from the point at which a candidate is identified . A patent provides a guarantee that a single company will have a short-term monopoly over the production of a new drug. However, competition amongst therapeutic areas as well as "hot" areas such as HIV, pain, diabetes, results in very short-term monopoly. Development folks are under extreme pressure to 1

© 2001 American Chemical Society

Nafissi et al.; From Bench to Pilot Plant ACS Symposium Series; American Chemical Society: Washington, DC, 2002.

1

2

avoid any delays in getting a drug to market. For example, G . D . Searle's Celebrex was on the market for two months before Merck introduced Vioxx. In 1999, R & D spending increased by 14 percent . With R & D spending increasing faster than sales, and patent expirations outpacing new chemical entity approvals, the industry is under tremendous pressure to improve the product development cycle. Complex products and chemistries such as potent drugs result in high R & D expenditure. For example, potent drugs require total containment facilities. Such facilities are expensive to build and operate. On the other hand, the worldwide sales of single-isomer chiral drugs have increased from 1 percent in 1985 to 12 percent in 2000 . Single isomer chiral drug sales should reach $500 million in 2000 . Pharmaceutical sales were estimated at $97 billion in 1998, 11% higher than 1997's $87 billion . The situation intensifies with the demand for lower costs from governments and managed care organizations, generics and competition from newly industrialized countries such as China and India. The benchmark of success in the pharmaceutical industry being the release of a blockbuster drug, their production now lies exclusively in the hands of a small number of large drug companies that have successfully merged, and consequently seek lean and portfolio specific developments with high levels of return. The increasing level of investment required to maintain an innovative drug company and deliver a significant number of important drugs to the marketplace has illustrated the importance of process research and development in a successful product development cycle. 2

3

Downloaded by 117.255.209.72 on March 5, 2016 | http://pubs.acs.org Publication Date: April 19, 2002 | doi: 10.1021/bk-2002-0817.ch001

3

4

II. The Drug Development Cycle Preclinical development: During preclinical development a company evaluates the identified candidate and the process research group supplies material to the formulators, the pharmacologists and the pharmacokinetics group. Some companies invest in process development, more aggressively than others. In this stage, several animal models are used to evaluate toxicity and pharmacokinetic properties of the compound. After completing preclinical testing, the company files an Investigational New Drug Application (IND) with the Food and Drug Administration (FDA) to begin to test the drug in humans. The I N D becomes effective i f the F D A does not disapprove it within 30 days. The I N D shows results of previous experiments, how, where and by whom the new studies will be conducted; the chemical structure of the compound; how it is thought to work in the body; any toxic effects found in the animal studies; and how the compound is manufactured. In addition, the IND must be reviewed and approved by the Institutional Review Board where studies will be conducted,

Nafissi et al.; From Bench to Pilot Plant ACS Symposium Series; American Chemical Society: Washington, DC, 2002.

3

and progress reports on clinical trials must be submitted at least annually to the FDA.

Downloaded by 117.255.209.72 on March 5, 2016 | http://pubs.acs.org Publication Date: April 19, 2002 | doi: 10.1021/bk-2002-0817.ch001

The majority of time and resources in the drug development cycle are consumed by the process of evaluating safety and efficacy in human patients. Clinical trials are divided into three phases. Phase I Trials: During phase I trials, the drug is administered at several dosages to healthy volunteers to determine whether there are any intolerable side effects. Although even minor side effects, such as a rash at the site of injection, are investigated, they are usually not enough to halt trials. The drug is typically administered in a prototype formulation such as a capsule or injection. These tests take about a year and involve about 20 to 80 healthy volunteers. The tests study a drug's safety profile, including the safe dosage range. The studies also determine how a drug is absorbed, distributed, metabolized and excreted, and the duration of action. Phase II Trials: During phase II trials, emphasis shifts to demonstrating the drug's efficacy in controlled studies. In this phase, controlled studies of approximately 100 to 300 patients (people with the disease) assess the drug's effectiveness and take about two years. These studies are typically carried out by giving the drug to one group of patients and a placebo or alternative treatment to a control group. These drugs are often double blind: neither the people administering the drug nor the patients know whether they are receiving the drug, the placebo, or an alternative. It is during this phase that the formulation group designs a number of dosage forms and attempts to determine which performs best in human patients. During phase II trials, process development has to provide material to two groups; the formulation group, and the clinical development group. The formulation group needs high-quality product for their analytical experiments, while the clinical group needs material for human testing. The demand for the bulk active intensifies as the formulation studies intensify and the number of patients increases. Phase III Trials: This phase last about three years and usually involves 1,000 to 3,000 patients in clinics and hospitals. The start of phase III trials is perhaps the most important milestone in the drug development process. The purpose of this phase is to generate definitive data on the safety and efficacy of the drug in large-scale, long

Nafissi et al.; From Bench to Pilot Plant ACS Symposium Series; American Chemical Society: Washington, DC, 2002.

4

term, multi-site trials. By the time a drug has reached phase III there is an 85 percent probability that it will reach the market. Phase III clinical trial represents an important milestone to chemical development. During this phase, process development focuses on finalizing all details of the process and proceeding to validation. Data from these validation run, usually three, are submitted to the F D A (Food and Drug Administration) as part of the New Drug Application (NDA) filling.

Downloaded by 117.255.209.72 on March 5, 2016 | http://pubs.acs.org Publication Date: April 19, 2002 | doi: 10.1021/bk-2002-0817.ch001

III.

Scale-up of Chemical Processes

Scale-up is inherent in all industrial activity. Scale-up is constantly on the minds of chemists and engineers concerned with the development of new processes or expansion of existing ones. When a new chemical process or a change of a process moves from the laboratory to the pilot plant to the manufacturing facility, unexpected problems are often encountered. The problems could be of either chemical or physical nature, or a variation of both. One of the most frustrating difficulties that can be encountered is the presence of impurities that are not considered or studied in the small laboratory scale. Since scale-up is the theme of this report we have defined it as: The successful startup and operation of a commercial process whose design is in part based upon experimentation and demonstration at a pilot scale of operation The concept of successful includes production of the product at planned rates, at the projected cost, and to the desired quality standards. Obviously to meet the desired cost we must consider the purchase prices of raw materials, the product yield, and the return on capital, but also the overall safety of the operation, the personnel, the public and the environment. To be successful at the scale-up of chemical processes requires the utilization of a broad spectrum of technical skills and a mature understanding of the total problem under study. The chemist's knowledge of the chemical literature and of the raw material database may restrict the choice of routes made. I cannot stress too much the importance of keeping up with the chemical literature as an essential part of the discipline of chemical development. The literature should be surveyed for chemistry which is applicable on a large scale, e.g. cheap reagents, useful catalysts, reactions which could be carried out in water or under phase transfer conditions and reactions which use common bases such as sodium carbonate instead of organolithium reagents.

Nafissi et al.; From Bench to Pilot Plant ACS Symposium Series; American Chemical Society: Washington, DC, 2002.

5

Indeed, to follow a direct path from laboratory data to the pilot plant requires either information that is often unavailable or scientific and engineering judgements,beyond those normally considered possible or desirable.

Downloaded by 117.255.209.72 on March 5, 2016 | http://pubs.acs.org Publication Date: April 19, 2002 | doi: 10.1021/bk-2002-0817.ch001

IV.

The Role of Chemical Development

The development chemist's job is the design of a process with the following qualities: a) The process must be safe. b) It should be cost efficient. Scale-up processes do not involve only technical decisions and compromises. The selected compromise always has an economic aspect since it is never possible to establish exactly what an industrial process should be. There are always restrictions of time and money. c) The process must be ecologically sound. The costs involved in meeting environmental, occupational health and safety, and consumer product safety requirements are so significant that they can, and often do, become prime considerations in whether to proceed with process development and scale-up. d) The process must be reproducible and robust. e) The chemistry must fit the existing equipment. To design a process with the desired qualities, the development chemist must understand the chemistry and the mechanisms. Process development and scale-up require multidisciplinary cooperation between organic chemists, analytical chemists, process engineers, pharmacologists, toxicologists, clinicians and marketing specialists. Chemical engineers are involved in plant trials, plant modification or new plant construction. Chemical engineers should be an essential part of the development team, as they bring a different point of view. A chemical engineer involved in bulk chemical production, envisages the pilot plant as a purpose-built plant designed to test a process, contrary to the development chemist, who sees the plant as a logical extension of a typical laboratory set-up of three-neck flask with addition funnel, stirrer and condenser. The cooperation of chemists and chemical engineers is vital to the success of scale-up, particularly the later stages of introduction of a process to full plant scale. Chemical engineers teach chemists the importance of heat transfer, mass transfer and kinetics, and other subjects with which the chemist may be less familiar. When a development chemist begins his task of synthesizing a target compound, the following information is usually available: a) A research method for making gram quantities, b) Possibly a sample, c) Possibly some analytical methods and

Nafissi et al.; From Bench to Pilot Plant ACS Symposium Series; American Chemical Society: Washington, DC, 2002.

Downloaded by 117.255.209.72 on March 5, 2016 | http://pubs.acs.org Publication Date: April 19, 2002 | doi: 10.1021/bk-2002-0817.ch001

6

cleaning methods, d) A patented synthetic route which may not be, and usually is not the best way to prepare the compound. It is simply the way a medicinal chemist decided to prepare several analogs of a class of compounds for testing. Therefore it is vital to take a long term approach and seek the best route at the start. The rule of thumb is that the shortest route is usually the best A short route means shorter plant time which translates in lowering capital cost. To choose a synthetic route it is important to generate several paper routes. Talk to colleagues and consultants, search the literature for similar compounds. Finally decide on a few which appear to have a high chance of success, but also try some speculative routes which could be beneficial even if there is little literature precedent. In order to design new synthetic routes to produce inexpansive products, it is important to choose the correct raw material. The chemist working on the development and scale-up of a new chemical entity, needs to have a wide knowledge of the fine chemicals market so that he knows not only what is available but also how much it costs. Often the only reason a chemical is not available in bulk is lack of demand.

V.

Optimization in Chemical Development

Chemical development involves not only synthetic route selection, but also optimization, scale-up and further improvement of the synthetic method until an efficient process is obtained. The development chemist's task is to convert a laboratory synthetic route, which used expensive reagents and very dilute reactions to a robust manufacturir~ process. In doing so the development chemist should scale-up the process 10 1-30 Kg. Scaling up a process allows the development chemist to test the process at the pilot plant level and to identify problems. He should learn how to handle reactants, intermediates and waste streams. How are isolations done? Are filtrations fast or slow? What kind of filtering equipment is needed? To scale-up a process from the laboratory to the pilot plant the development chemist must have an appreciation of chemical engineering principles. Understanding of heat transfer and mass transfer is essential in the successful scale-up of a new process. To control the temperature with respect to time is one of the most important aspects of chemical engineering. Reaction temperatures must be controlled in order to ensure selectivity of the process, reproduce results accurately and to prevent thermal runaways. Heat transfer is not only important in the reaction but in the work up as well. For example, to control the temperature during exothermic neutralizations, crystallizations, and distillations. In many chemical processes the rate of external heating may not be important, but the rate of external cooling can be very critical when exotherms take place.

Nafissi et al.; From Bench to Pilot Plant ACS Symposium Series; American Chemical Society: Washington, DC, 2002.

7

Reactions v/ith low volume are most difficult to control due to the fact that the removal of heat is proportional to contact surface area as well as A T . Heat transfer can be effected by a number of factors such as rate of agitation, turbulent or laminar flow, viscosity of reaction medium, density, temperature, shape and surface of vessel, exothermicity of reaction and phase changes. The heat transfer can be controlled by using the correct vessel for the batch size. The material of construction (stainless steel, glass etc.) as well as the design and agitator are important. Heat evolved is proportional to number of moles of reactant(s), and is therefore proportional to volume of solution (r ) . Removal of heat is also proportional to surface area (r ) . Therefore as vessel size increases, volume-tosurface ratio also increases. This means that heat transfer becomes more difficult. The development chemist should perform a risk assessment on the process he is scaling up. For example, can a process temperature be controled by the existing cooling system? What temperature could be attained after the runaway of the desired reaction? A t which moment does cooling failure have the worst case consequences? How fast is the runaway of the desired reaction? Mass transfer is also important in successfully scaling up a process. Mass transfer (which is not the same as agitation) becomes very important in a reaction with more than one phase and in work-up and purification. For substances to react they must come into contact. In a two-phase system, mass transfer is affected by the rate of diffusion to and across the interfacial boundary and the rate of diffusion of products from the reaction zone. Mass transfer is affected by the size of the interfacial area or surface as well. 3

Downloaded by 117.255.209.72 on March 5, 2016 | http://pubs.acs.org Publication Date: April 19, 2002 | doi: 10.1021/bk-2002-0817.ch001

2

5

5

A large vessel is not identical to a small vessel in most of the mixing and fluid mechanics parameters that may be involved in determining process results. To scale up from a small laboratory vessel to a large vessel in the pilot plant or in production, understanding of some of the principles of fluid mixing is required. This ensures consistency in purity and yield of the product. The development chemist knows all too well that agitation can be fatally different in the plant. For example, laboratory glassware is spherical where plant equipment is more cylindrical, and plant vessels are baffled resulting in better mixing. Good mixing is vital in obtaining good mass transfer, especially when we are dealing with a viscous medium. Many times, engineers spend a lot of time designing an agitator for a particular process. Some type of agitators are: The impeller, which consists of three radial and curved blades assembled axially with 1-2 baffles*. The twin agitator, which is made up of several two-bladed wheels rotated ninety degrees and assembled with or without baffles*. The anchor, which is assembled axially without baffle or with one thermopoeket*. The loop agitator, which is a tubular gate agitator6. The uniflow axial turbine, which is made up of pitched blades to give high axial flow and low shear*. The pitched turbine is a six-bladed propeller assembled axially with 1-4 beaver-tail baffles or eccentrically without baffled. The radial turbine is made up of flat bladed to give high radial flow and

Nafissi et al.; From Bench to Pilot Plant ACS Symposium Series; American Chemical Society: Washington, DC, 2002.

8

6

high shear . Finally the disc turbine is a turbine wheel with six radial blades assembled axially with or without 1-4 beaver-tail baffles . To mimic the laboratory mixing conditions, a vessel must be designed to have the same Reynolds number (Nre). The Reynolds number can be obtained from the following formula : 6

7

Nre=Dvp/|ii

Downloaded by 117.255.209.72 on March 5, 2016 | http://pubs.acs.org Publication Date: April 19, 2002 | doi: 10.1021/bk-2002-0817.ch001

(1) This formula takes into account the diameter of the vessel (D), the velocity of the fluid (v), the density (p) and the viscosity (ji). The Reynolds number has no dimensions. For high viscosity applications one can see that we need large scale diameter agitator and low speed. On the other hand for low viscosity fluids the diameter of the agitator may be as low as one third the vessel diameter and the speed high. In scale-up the ratio of impeller diameter to vessel diameter is an important factor. To select a particular type of reactor in any stage of scale-up, it is important to identify your purpose and/or goal. For example, for the small scale manufacturer, few criteria are as consequential as flexibility with respect to operating conditions and product demand. The product market might not justify a massive research program or it might be ideal to produce several compounds out of the reactor. The economics of the overall process are often little influenced by the cost of the reactor. The ability of a chosen reactor to optimize product selectivity, or maximize productivity, is far more important in practice than the minimization of the reactor cost. Control of temperature, and mass transfer is of great importance in the design or choice of reactor in scale-up. The rates and equilibria of many reactions are profoundly affected by temperature. Accordingly, so are side reactions, by­ product formation, yield, selectivity, and so on. The great variety in reactor types and the fact that no single type is suitable for all purposes makes it necessary to establish criteria for selection. One such criterion is the type of mixing needed for the process in question. The role of mixing in all these various processes may not be completely understood. This makes a qualitative understanding of the differences between the pilot plant and the laboratory and their possible effects much more important to understand. The purpose of scale-up is to actually observe, measure, analyze, and record data.

Nafissi et al.; From Bench to Pilot Plant ACS Symposium Series; American Chemical Society: Washington, DC, 2002.

9

Downloaded by 117.255.209.72 on March 5, 2016 | http://pubs.acs.org Publication Date: April 19, 2002 | doi: 10.1021/bk-2002-0817.ch001

VI.

Process Safety

No process can be made one hundrend percent safe. However, one can identify hazards and, if the hazard is severe, avoid such a chemical or process, or if the hazard is moderate, take precautions that minimize the risk. Safety hazards can be divided into four categories: thermal instability, toxicity, flammability, and explosiveness. Typically the in-house safety laboratory measures the decomposition temperature of all reagents, intermediates, solvents, distillation residues and evaporation residues, and any exotherms associated with the decomposition, so that one stays well below these temperatures in the process. The heat of reactions is measured to ensure adequate cooling capacity of the reactor before scaling up a reaction. This minimizes the risk of runaway reactions. The LD50 and carcinogenicity of compounds are measured as well. For known compounds, one can look up the data in manuals, such as Sax's Dangerous Properties of Industial Materials. For new compounds, the tests are done inhouse, both the L D and the Ames test. There is no hard rule for what is too toxic in the plant, but typically the rule of thumb may be following table I. Solvents that are carcinogens are avoided, e.g., chloroform, carbon tetrachloride, dioxane, benzene and hexamethylphosphoric triamide*. 5 0

Table I. Toxicity of Chemicals

LD o(mR/KR) 15000 5

Toxicity Dangerously toxic Seriously toxic Very toxic Moderately toxic Slightly toxic Low toxicity

Nafissi et al.; From Bench to Pilot Plant ACS Symposium Series; American Chemical Society: Washington, DC, 2002.

Downloaded by 117.255.209.72 on March 5, 2016 | http://pubs.acs.org Publication Date: April 19, 2002 | doi: 10.1021/bk-2002-0817.ch001

10

Another safety hazard is flammability. It is a concern mainly with solvents that are volatile. One can easily find the following information: ignition temperature, flash point, vapor pressure, vapor density and the mixture of solvent and air that is flammable. The lower and the wider the latter value, the more hazardous the solvent, since more likely one will encounter the conditions for flammability in the plant. Again, there is no hard line between what is safe and what is not, but solvents with flash point of less than -18°C are not used. A solvent with a flash point above -18°C can be used but special precautions must be taken such as grounding of all drums and reactors to prevent buildup of electrostatic electricity and excluding all other sources of ignition. A l l other solvents (toxic or flash point