Carbon Nanofiber Hybrids

Oct 10, 2017 - College of Environmental Science and Engineering, North China Electric ... of Advanced Nuclear Energy Technology, Institute of Nuclear ...
0 downloads 3 Views 2MB Size
Subscriber access provided by Service des bibliothèques | Université de Sherbrooke

Article

Plasma-Facilitated Synthesis of Amidoxime/Carbon Nanofiber Hybrids for Effective Enrichment of 238U(VI) and 241Am(III) Yubing Sun, Songhua Lu, Xiangxue Wang, Chao Xu, Jia-Xing Li, Changlun Chen, Jing Chen, Tasawar Hayat, Ahmed Alsaedi, Njud S. Alharbi, and Xiangke Wang Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.7b02745 • Publication Date (Web): 10 Oct 2017 Downloaded from http://pubs.acs.org on October 10, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 34

Environmental Science & Technology

1

Plasma-Facilitated Synthesis of Amidoxime/Carbon Nanofiber Hybrids for

2

Effective Enrichment of 238U(VI) and 241Am(III)

3

Yubing Sun†,‡, Songhua Lu†, Xiangxue Wang‡, Chao Xu , Jiaxing Li†, Changlun

4

Chen†, Jing Chen&, Tasawar Hayat⊥, ∥, Ahmed Alsaedi∥,Njud S. Alharbi∥, Xiangke

5

Wang‡, §*



6



7

230031, P.R. China

8



9

University, Beijing 102206, P.R. China

Institute of Plasma Physics, Chinese Academy of Science, P.O. Box 1126, Hefei,

College of Environmental Science and Engineering, North China Electric Power

10



11

of Nuclear and New Energy Technology, Tsinghua University, Beijing, 100084, P.R.

12

China

13

§

14

Institutions, School for Radiological and Interdisciplinary Sciences, Soochow

15

University, Suzhou 215123, P.R. China

16



NAAM Research Group, King Abdulaziz University, Jeddah 21589, Saudi Arabia

17



Department of Mathematics, Quaid-I-Azam University, Islamabad 44000, Pakistan

18

Collaborative Innovation Center of Advanced Nuclear Energy Technology, Institute

Collaborative Innovation Center of Radiation Medicine of Jiangsu Higher Education

* Corresponding Author: E-mail: [email protected] (X. Wang); Phone:

19

+86-10-61772890; fax: +86-10-61772890

20

ABSTRCT. Plasma- and chemical-grafted amidoxime/carbon nanofiber hybrids

21

(p-AO/CNFs and c-AO/CNFs) were utilized to remove

238

U(VI) and 241Am(III) from

ACS Paragon Plus Environment

Environmental Science & Technology

22

aqueous solutions, seawater and groundwater. Characteristic results indicated the

23

more nitrogen-containing groups of p-AO/CNFs compared to c-AO/CNFs. The

24

maximum adsorption capacities of p-AO/CNFs at pH 3.5 and T = 293 K (588.24 mg

25

238

26

were significantly higher than those of c-AO/CNFs (263.18 and 22.77 mg/g for

27

238

28

highly effective, low-cost and environmentally friendly method. Adsorption of

29

238

U(VI) on AO/CNFs from aqueous solutions was significantly higher than that of

30

238

U(VI) adsorption from seawater and groundwater, moreover AO/CNFs displayed

31

the highest effective selectivity for

32

Adsorption of

33

shell) by EXAFS analysis, which was supported by surface complexation modeling.

34

Three inner-sphere complexes gave excellent fits to pH-edge and isothermal

35

adsorption of

36

utilization of plasma-grafted, AO-based composites to the preconcentration and

37

immobilization of lanthanides and actinides in environmental remediation.

38

INTRODUCTION

39

The contamination of uranium has been as a worldwide concern due to excessive

40

uranium mining and milling operations around the world.1 Over last several decades,

41

many investigations regarding the removal of radionuclides with various adsorbents

42

have been extensively investigated, including clay minerals,2-5 metal (hydr)oxides6-9

U(VI) and 40.79 mg

U(VI) and

241

241

Am(III) per gram from aqueous solutions, respectively)

Am(III), respectively), which indicated that plasma-grafting was a

238

238

238

U(VI) compared to the other radionuclides.

U(VI) onto AO/CNFs created inner-sphere complexes (e.g., U-C

U(VI) on the AO/CNFs. These observations are crucial for the

ACS Paragon Plus Environment

Page 2 of 34

Page 3 of 34

Environmental Science & Technology

43

and carbon-based nanoparticles.10-13 Although substantial progress has been achieved

44

in several decades, the removal of U(VI) at low pH and under trace concentrations is

45

still a challenge due to their limited adsorption capacities. Additionally, americium

46

(241Am(III)) is a radiotoxic nuclear wastes that can be discharged towards the

47

environments during the processing, storage and disposal of nuclear wastes. In our

48

previous studies, the removal of

49

investigated by various techniques.14-16 However, few studies regarding the removal

50

of

51

important to develop new materials to remove uranium and americium from aqueous

52

solutions at extreme conditions with the faster adsorption rates, higher selectivities

53

and larger adsorption capacities.

54

Owing to its environmentally friendly, accessible raw materials and its low cost,

55

carbon nanofiber (CNF) is an emerging class of carbon-based nanoparticles that have

56

recently seen promising use as an adsorbent to remove a variety of organic19-24 and

57

inorganic pollutants.25-28 For example, Sun et al. observed that CNF displayed high

58

adsorption capacities for radionuclides such as 125 mg U(VI)/g and 91 mg Eu(III)/g

59

at pH 4.5.29 Similar results have been obtained for heavy metals, where it was

60

reported the high adsorption capacities of CNF for heavy metals such as 423.7 mg

61

Pb(II)/g and 221.3 mg Cr(VI)/g.30 However, these CNFs displayed poor selectivities

62

towards certain radionuclides of interest. Therefore, further investigation in improving

63

the selectivity of CNF to uranium is of great importance. Recently, numerous studies

241

241

Am(III) with carbon nanotubes was extensively

Am(III) with other carbon-based materials have been published.17, 18 Thus, it is

ACS Paragon Plus Environment

Environmental Science & Technology

Page 4 of 34

64

have focused on amidoxime-based composites as promising candidates for U(VI)

65

sorption due to their high capacities and affinities in chelating uranyl ions.31-35 Zhang

66

et al. used EXAFS and theoretical calculations to investigate the extraction

67

mechanism of uranium amidoxime ligands with an η2-binding mode, but limited

68

information regarding the experimental data has been reported.36 To our knowledge,

69

the interaction mechanism of efficient, selective enrichment of U(VI) on amidoxime

70

composites has not yet been explored under different experimental conditions.

71

Poly(amidoxime) can be easily grafted onto carbon-based materials through a

72

plasma-induced grafting method. This plasma method can produce chemically active

73

species to change the properties of an adsorbent’s surface.37-40 The objectives of this

74

study were to (1) characterize the nanostructure of plasma- and chemical-grafted

75

AO/CNFs (called p-AO/CNFs and c-AO/CNFs, respectively) by SEM, FT-IR and

76

XPS techniques, (2) elucidate the effect of water chemistry on 238U(VI) and 241Am(III)

77

adsorption by two kinds of AO/CNFs using batch techniques, and (3) investigate the

78

interaction mechanism between two kinds of AO/CNFs with

79

EXAFS and surface complexation modeling. This study will provide insights into the

80

preparation of AO/CNFs with high adsorption performances and high selectivities for

81

radionuclides using a plasma-grafting method, which is more efficient, less expensive

82

and environmentally friendlier than the chemical method.

83

EXPERIMENTAL DETAILS

84

Materials. Bacterial cellulose was obtained as a gift from Hainan Yeguo Food

ACS Paragon Plus Environment

238

U(VI) using XPS,

Page 5 of 34

Environmental Science & Technology

85

Company Limited. The reagents used in this study (dimethylformamide-DMF,

86

acrylonitrile-AN, hydroxylamine-NH2OH.HCl, Na2CO3) were of analytical grade and

87

purchased from Sinopharm Chemical Reagent Co., Ltd. (Shanghai). The

88

stock solutions (60 mg/L) were prepared by dissolving uranyl nitrate (> 99.9 % purity,

89

Sigma-Aldrich) into a 4 % HNO3 solution under anaerobic conditions (volume ratio

90

of H2/N2= 5/95, O2 concentration < 0.5 ppm). The 241Am(III) standard solutions were

91

purchased from Isotope Product Laboratories (IPL, Burbank, USA).

92

Synthesis of AO/CNFs. p-AO/CNFs and c-AO/CNFs were synthesized through the

93

methods of plasma-discharge and chemical polymerization, respectively. Firstly, the

94

CNF was obtained by the pyrolysis of bacterial cellulose at 170 °C for 3 h under N2.41

95

Then, 1.0 g of CNF was added to a conical flask, which was then sealed by silicone

96

caulk. The N2 plasma method conditions were 70 W, 10 Pa, 60 Ma and 650 V.38 After

97

the N2 plasma method, the conical flask was heated to 60 °C and 100 mL of a DMF

98

solution containing 50 mL of AN was added under continuous stirring, which was

99

continued for 8 h. Then, hybrids were repeatedly washed with DI water until

100

propylene could not be detected by high-performance liquid chromatography. Finally,

101

the aforementioned hybrids were reacted with NH2OH.HCl to convert the AN group

102

to an amidoxime (AO) group.36,

103

hybrids and 2.5 g of NH2OH.HCl were added into 150 mL of CH3OH/H2O (v/v=

104

50/50) and stirred for 12 h at 60 °C. Solution pH was adjusted to 7.0 by adding

105

saturated Na2CO3 solution. Then, the products were washed by DI water (60 mL) and

42

238

U(VI)

Briefly, the procedure is as follows: 2.0 g of

ACS Paragon Plus Environment

Environmental Science & Technology

106

methanol (60 mL) three times each. The p-AO/CNFs were obtained by drying them in

107

a vacuum oven at 60 °C overnight. The c-AO/CNFs were also used to compare their

108

sorption performance. Briefly, 1.0 g of CNF and 100 mL of a DMF solution

109

containing 50 mL of AN were added to a conical flask, and the suspension was

110

reacted under continuous stirring at 60 °C for 8 h. Suspension pH was adjusted to 7.0,

111

and 2.5 g of NH2OH.HCl was added. Then, the mixture was washed by DI water (60

112

mL) and methanol (60 mL) three times each and finally dried in a vacuum oven at

113

60 °C for 12 h. The contents of amidoxime groups of p- and c-AO/CNFs determined

114

by HCl adsorption method were approximately 33 and 26 mmol/g, respectively,

115

indicating that the plasma-grafting was the more effective, inexpensive and

116

environmentally friendly method. More details on the determination of the grafting

117

yield are provided in Supporting Information (SI).

118

Characterization. The nanostructure and morphology of the AO/CNFs were

119

illustrated by SEM (S-4800, Hitachi, Japan). The SEM samples were prepared as

120

follows: 10.0 mg of the samples was dispersed into 5.0 mL of ethanol in the ultrasonic

121

conditions inside the golvebox, and then suspensions were added on a copper grid,

122

and then transported to the microscope after dried on a glass slide. FT-IR and XPS

123

spectra were obtained on a PerkinElmer IR-843 spectrometer and an Axis-Ultra

124

(Kratos, UK) with an Al Kα line at 10-8 Torr, respectively. Samples for XPS analysis

125

were calibrated by the C 1s sp2 spectra at 284.6 eV. The elemental contents of the

126

samples were obtained from an elemental analyzer (Carlo-Erba 1106, Italy). The ζ

ACS Paragon Plus Environment

Page 6 of 34

Page 7 of 34

Environmental Science & Technology

127

potential of the AO/CNFs was determined by a Malvern Zetasizer (632.8 nm, He-Ne

128

laser).

129

Batch Sorption Protocols. All sorption experiments were conducted in triplicate in

130

an anaerobic chamber with a background electrolyte of 0.01 mol/L NaCl at 293 K.

131

Briefly, an uniform suspension of AO/CNFs (1.2 g/L) was firstly obtained by mixing

132

0.6 g AO/CNFs solid and 500 mL DI water under ultrasonic conditions, and then 3

133

mL AO/CNFs suspension and 3 mL of

134

solution (background electrolyte) was added into 10 mL polycarbonate tubes to obtain

135

the desired solid to liquid ratio (m/v) of 0.6 g/L. The adsorption isotherms of

136

241

137

compare the sorption performance of AO/CNFs. The compositions of seawater and

138

groundwater were summarized in Table S1. Suspension pH of each tube was adjusted

139

by a negligible volume of NaOH or HCl solution (0.1-1.0 mol/L). The regeneration of

140

the sorbent was conducted in five consecutive cycles to evaluate its stability and

141

reusability. In each cycle, the sorbent was eluted by a 0.1 mol/L HCl solution and then

142

washed with DI water three times for reuse. The suspensions were stirred under

143

reciprocal shaker 24 h and the each tube was centrifuged at 7400 g for 15 min. The

144

concentrations of

145

inductively coupled plasma-mass spectrometry (ICP-MS, 7700x Agilent Technologies)

146

and liquid-scintillation-counting (Liquid Scintillation Analyzer, Packard 3100 TR/AB,

147

PerkinElmer) with the ULTIMA GOLD AB scintillation cocktail, respectively. The

238

U(VI)/241Am(III) solution with the NaCl

Am(III)/238U(VI) from spiked seawater and groundwater were also conducted to

238

U(VI) and

241

Am(III) in the supernatants were measured by

ACS Paragon Plus Environment

Environmental Science & Technology

148

sorption amounts were calculated by the difference in the concentrations before and

149

after the sorption experiments.

150

EXAFS Analysis. The U LIII-edge EXAFS spectra were taken on the XAS beamline,

151

with a double-crystal Si(111) monochromator, at the Shanghai Synchrotron Radiation

152

Facility (SSRF). EXAFS spectra were obtained in the fluorescence model with a

153

64-element Ge detector. The ATHENA software package was used to normalize the

154

merged spectra,43 and ARTEMIS was employed to fit the EXAFS data based on the

155

theoretical phase and amplitude function from the crystallographic data of uraninite.44

156

However, the samples of

157

by EXAFS analysis due to fluorescence quenching effects.14, 16

158

RESULTS AND DISCUSSION

159

Characterization. The morphologies of the two kinds of AO/CNFs were investigated

160

by SEM. As shown in Figure 1A and 1B, the two kinds of AO/CNFs had the rough

161

and tidy nanofibers. No significant difference between the morphologies of the two

162

kinds of AO/CNFs was observed, indicating that plasma technique is a reliable and

163

effective approach for CNF functionalization. As shown by the FT-IR spectra in

164

Figure 1C, the characteristic bands at ~3400, 1655, 1500, 1290 and 935 cm-1 were

165

attributed to the stretching vibrations of O-H/N-H, C=C, C=N, C-N, and N-O groups,

166

respectively.42 Additionally, the relative intensity of the N-O groups in the

167

p-AO/CNFs was remarkably higher than c-AO/CNFs, indicating that more

168

amidoxime groups were grafted onto the surface of the CNFs by the plasma method.

241

Am(III) on AO/CNF composites cannot be investigated

ACS Paragon Plus Environment

Page 8 of 34

Page 9 of 34

Environmental Science & Technology

169

As shown by the high-resolution N 1s XPS spectra in Figure 1D, the binding energies

170

of N 1s in p-AO/CNFs were significantly shifted higher compared to those of

171

c-AO/CNFs. The fitted peaks of the XPS spectra for the two kinds of AO/CNFs can

172

be deconvoluted into pyridinic (398.5 eV), pyrrolic (399.9 eV), graphitic (401.3 eV)

173

and N-oxide (402.9 eV) moieties by the N-O, C=N and C-N groups,42 which further

174

indicated that amidoxime groups had been satisfactorilly grafted onto the CNFs

175

surface. Additionally, the relative peak area of the N-O in p-AO/CNFs was

176

significantly higher than that in c-AO/CNFs, which agrees with the FT-IR results. As

177

shown by the thermal gravimetric analysis (TGA) in Figure S1A, the degradation

178

temperatures for the two kinds of AO/CNFs occurred at ~ 500 °C, whereas the

179

maximum weight loss was observed at ~ 680 °C, indicating that AO/CNFs had a

180

strong thermal stability. The significant decrease in the weight at ~ 550-650 °C could

181

be due to the pyrolysis of functional groups (i.e., carboxyl, hydroxyl and amidoxime

182

groups) in AO/CNFs.45 The components of the two AO/CNFs, as obtained by XPS

183

and elemental analysis, are shown in Table S2. The relative amount of N (6.57 % as

184

determined by XPS analysis) for p-AO/CNFs was significantly higher than that of

185

c-AO/CNFs (4.26 %), as summarized in Table S2. These results confirmed that the

186

AO/CNFs had much more oxygen- and nitrogen-bearing functional groups and had

187

good thermal stabilities.46 Additionally, more nitrogen- containing functional groups

188

were grafted onto the surface of the p-AO/CNFs compared to the c-AO/CNFs.

189

Effect of Reaction Time. Figure 2A shows the adsorption of 238U(VI) and 241Am(III)

ACS Paragon Plus Environment

Environmental Science & Technology

238

Page 10 of 34

U(VI) and

241

190

onto the two kinds of AO/CNFs at different reaction time.

191

adsorption onto both of AO/CNFs dramatically enhanced with increasing reaction

192

time from 0 to 1 h, and remained the high level adsorption at reaction times of more

193

than 3 h. As shown in the inset of Figure 2A, the adsorption rates of

194

241

195

kinetics data were simulated to pseudo first order and pseudo second order kinetic

196

models. More details concerning this fitting are provided in the SI. As shown in

197

Figure S2 and Table S3 in the SI, the adsorption kinetics of

198

on the two kinds of AO/CNFs can be well simulated by a pseudo second order kinetic

199

model (correlation coefficients (R2) >0.999) compared to pseudo first order kinetic

200

mode (R2 < 0.91), which was in accordance with previous studies. 47-49

201

Effect of pH and Ionic Strength. Figure 2B shows the effect of pH on 238U(VI) and

202

241

203

AO/CNFs observably increased at pH 1.0- 5.0, and then kept the high adsorption at

204

pH 5.0-6.5, while the adsorption of

205

enhanced adsorption of 241Am(III) onto the two kinds of AO/CNFs was also observed

206

at pH 3.0-5.0.

207

markedly higher than c-AO/CNFs. As shown by the zeta potentials in Figure S1B,

208

two kinds of AO/CNFs had a negative charge at pH > 2.5. The distribution and

209

corresponding equilibrated parameters of

210

aqueous solutions is shown in Figure S3 and Table S4, respectively. The main U(VI)

238

Am(III)

U(VI) and

Am(III) on p-AO/CNFs were significantly higher than those of c-AO/CNFs. The

Am(III) adsorption onto the two kinds of AO/CNFs.

238

U(VI) and

241

238

238

238

U(VI) and

241

Am(III)

U(VI) adsorption on

U(VI) was slightly decreased at pH > 6.5. The

Am(III) adsorption on p-AO/CNFs at pH 2.0-4.0 was

238

U(VI) and

241

ACS Paragon Plus Environment

Am(III) species in the

Page 11 of 34

Environmental Science & Technology

211

species was UO22+ and various positive U(VI) speciation (e.g., UO2OH+,

212

(UO2)4(OH)7+ and (UO2)3(OH)5+) were observed at pH < 5.0 and pH 5.0-8.0,

213

respectively. However, the negative carbonato-uranyl complexes were observed at

214

pH > 8.0. The surface co-precipitate (i.e., schoepite) was observed at pH 6.0 -8.0

215

(Figure S3A). As shown in Figure S3B, the main

216

AmOH2+, Am(OH)2+ and Am(OH)3(aq) at pH < 5.5, 5.5 -7.5, 7.5 -11.5 and > 11.5,

217

respectively. Thus, the increased adsorption of 238U(VI) and 241Am(III) at pH 2.0 -5.0

218

was due to the electrostatic-attraction of positively charged UO22+/Am3+ species and

219

negative charge of AO/CNFs. The high adsorption of

220

attributed to the inner-sphere surface complexation/surface precipitate, while the

221

adsorption of 238U(VI) was decreased at pH > 7.5 due to the electrostatic-repulsion of

222

the negative charge AO/CNFs and the negative carbonato uranyl species such as

223

UO2(CO3)34- and UO2(CO3)22-.

224

Figure S4A and S4B show

225

different ionic strengths, respectively. Outer-sphere surface complexation was

226

influenced by ionic strength, while no effect of ionic strength on inner-sphere surface

227

complexation was demonstrated.50-52 Ionic strength had no effect on

228

adsorption, suggesting that the

229

was an inner sphere surface-complexation. It is noted that the adsorption of

230

and

231

to the occurrence of more available reactive sites such as nitrogen- and

241

238

241

Am(III) species were Am3+,

238

U(VI) at pH 5.0 -7.0 was

U(VI) adsorption onto the c- and p-AO/CNFs at

238

238

U(VI)

U(VI) adsorption onto the two kinds of AO/CNFs 238

U(VI)

Am(III) on p-AO/CNFs was significantly higher than that of c-AO/CNFs due

ACS Paragon Plus Environment

Environmental Science & Technology

Page 12 of 34

232

oxygen-containing function groups.

233

Adsorption Isotherms. Figure 3A shows the isothermal adsorption of 238U(VI) on c-

234

and p-AO/CNFs. Uranium loading concentration on p-AO/CNFs (e.g., 450 mg

235

uranium/g at equilibrated concentration of 2.5 mg/L) was remarkably higher than that

236

on c-AO/CNFs (170 mg uranium/g). As shown in Figure 3A and Figure S5A, the

237

sorption of U(VI) from seawater and groundwater was notably lower than that of

238

U(VI) sorption from aqueous solution due to strong competition between U(VI) and

239

other ions (such as Na+, Mg2+, Cl- and SO42- and HCO3-) for adsorption active sites.

240

The adsorption isotherms were simulated using the Langmuir and Freundlich models.

241

More details concerning the fitting of the Langmuir and Freundlich models are

242

described in the SI. As shown in Table S5, Langmuir model gave better fits for the

243

adsorption of

244

capacity of p-AO/CNFs at pH 3.5 and 293 K was 588.2 mg/g for

245

aqueous solutions, whereas the maximum adsorption capacities of p-AO/CNFs for

246

238

247

were 248.14 and 398.41 mg/g (Table S5), respectively. As shown in Table 2, the

248

adsorption capacity of p-AO/CNFs was significantly higher than those of other

249

AO-based composites such as AO/macroporous beads (3.5 mg/g),53 AO/mesoporous

250

carbon (4.6 mg/g),54 AO/mesoporous imprinted polymer (19.1 mg/g),55 AO/poly

251

(propylene) fibers (44 mg/g),56 AO/multiwalled carbon nanotubes (145 mg/g)57 and

252

AO/ polypropylene membranes (380.0 mg/g).58 These observations indicated that

238

U(VI) onto AO/CNFs (R2 > 0.995). The maximum adsorption 238

U(VI) from

U(VI) from seawater (at pH 8.1 and 293 K) and groundwater (at pH 7.8 and 293 K)

ACS Paragon Plus Environment

Page 13 of 34

Environmental Science & Technology

253

AO/CNF composites displayed a high adsorption performance for 238U(VI).

254

Figure 3B shows the adsorption performance of U(VI) on p-AO/CNFs with the other

255

radionuclides and heavy metals. The maximum adsorption capacities of p-AO/CNFs

256

at pH 3.5 were 167.34, 135.87, 40.79, 57.57, 69.97, 67.64 and 42.61 mg/g for Th(IV),

257

Eu(III), Am(III), Sr(II), Ni(II), Co(II) and Cs(I), respectively. This demonstrated that

258

p-AO/CNFs showed a highly selective adsorption for U(VI) compared to the other

259

radionuclides and heavy metals, due to η2-binding mode.58 Figure S5B shows the

260

regeneration

261

adsorption-desorption cycles. The maximum adsorption capacities of the p- and

262

c-AO/CNFs decreased from 588.23 to 530.68 mg/g and from 263.15 to 233.69 mg/g,

263

respectively. This slight decrease in the maximum adsorption capacity of the two

264

kinds of AO/CNFs could be attributed to mass loss during the adsorption/desorption

265

process. These findings showed that AO/CNFs had good recoverability and

266

recyclability for the removal of radionuclides in environmental remediation.

267

XPS Analysis. Figure 4A shows the scans of the XPS spectra for the p-AO/CNFs

268

after U(VI) adsorption and desorption. Compared to the original AO/CNFs, the

269

relative intensities of O 1s and N 1s significantly decreased after U(VI) adsorption,

270

indicating that the oxygen- and nitrogen-containing functional groups were

271

responsible for the highly effective adsorption of U(VI). It should be noted that the

272

change in the relative intensity of N 1s after U(VI) desorption was significantly less

273

than that of O 1s. This demonstrated that the nitrogen-bearing groups displayed a

of

the

two

kinds

of

AO/CNFs

ACS Paragon Plus Environment

through

five-successive

Environmental Science & Technology

274

stronger chemical affinity for U(VI) than the oxygen-bearing groups did. Figure 4B

275

and C shows the XPS spectra of O 1s and C 1s, respectively. XPS spectra of O 1s

276

were shifted to the lower energies after U(VI) adsorption (Figure 4B), whereas the

277

spectra were shifted to higher energies after U(VI) desorption, indicating that these

278

oxygen-bearing groups were responsible for the highly effective adsorption of U(VI).

279

The O 1s spectra of p-AO/CNFs could be deconvoluted into four sub-bands at a

280

binding energies of 530.6, 532.1, 533.1 and 534.2 eV, which were assigned to –OH,

281

C=O, C-O and adsorbed water, respectively. As shown in Figure 4C, the XPS spectra

282

of C 1s could be fitted with four peaks at 288.8, 286.4, 285.4 and 284.5eV, which

283

could be ascribed to the C=O, C-N/C-O, C=N and C-C species, respectively.54, 59, 60

284

Figure 4D shows the XPS detailed scan of p-AO/CNFs in the U 4f region after U(VI)

285

adsorption and desorption. The slight decrease in the relative intensities of U 4f after

286

desorption revealed that AO/CNFs displayed a strong chemical affinity for U(VI) at

287

low pH conditions.

288

EXAFS Analysis. EXAFS was applied to investigate the chemical species and

289

microstructure of U(VI) at the water-solid interface. Figure 5A and 5B shows the U

290

LIII-edge EXAFS spectra and the corresponding Fourier transform (FT), respectively,

291

of the two kinds of AO/CNFs. Table 3 summarized the various fitted constants such

292

as Debye-Waller factor (σ2), coordination number (CN) and bond length (R). As

293

shown in Figure 5A, no differences in the EXAFS spectra were observed between the

294

kinds of AO/CNFs. As shown in Figure 5B, the FT features at ~ 1.4 and 1.9 Å can be

ACS Paragon Plus Environment

Page 14 of 34

Page 15 of 34

Environmental Science & Technology

295

fitted by a two axial oxygen shell (U-Oax at 1.8 Å) and a five or six equatorial oxygen

296

shell (U-Oeq at 1.8 Å), respectively.61 The bond lengths of U-Oeq shell on the two

297

kinds of AO/CNFs were obviously longer than

298

contribution of a longer U–N shell.36 For both AO/CNFs, it should be noted that the

299

weak peaks at 2.3 Å can be fitted by a 1.5 carbon shell (U-C) at ~ 2.9 Å, indicating

300

the inner-sphere surface complexation of U(VI) on AO/CNFs at pH 3.5. Thus,

301

AO/CNFs showed promise as adsorbents for the highly effective and selective

302

adsorption of U(VI) in nuclear waste management applications.

303

Surface Complexation Modeling. Figure 6A-D shows the surface complexation

304

modeling of

305

concentrations. The main U(VI) speciation in aqueous solutions at pH < 5, pH = 8-9

306

and pH > 9 were UO22+, (UO2)3(OH)7- and UO2(CO3)23- species, respectively (Figure

307

S3A), therefore three U(VI) species were employed to simulate the adsorption

308

behaviors. As shown in Figure 6A and 6C, the pH-edge adsorption indicated that the

309

adsorption of 238U(VI) onto the two kinds of AO/CNFs can be fitted by a double layer

310

model, within error. The main species were SOUO2+, SO(UO2)3(OH)72- and

311

SOUO2(CO3)23- species at pH < 4, pH 4 -7 and pH > 7.0, respectively. The different

312

equilibrium parameters (log K values, Table 4) were observed for the two kinds of

313

AO/CNFs due to their different surface properties arising from the different

314

pretreatment methods. These optimized parameters derived from the pH-edge

315

adsorption, were used to fit the isothermal adsorption of U(VI) on c- and p-AO/CNFs

238

those in UO22+ due to the

U(VI) adsorption onto AO/CNFs at different pH and initial

ACS Paragon Plus Environment

238

U(VI)

Environmental Science & Technology

316

at pH 3.5. As shown in Figure 6B and 6D, the diffuse layer model (DLM) model gave

317

better fits to the isothermal adsorption of U(VI) on both kinds AO/CNFs. Sun et al.

318

also found that Eu(III) adsorption on graphene oxide can be well simulated with a

319

DLM using SOEu2+ and (SO)2Eu2(OH)22+ species.62 This surface complexation

320

modeling showed that U(VI) adsorption on c- and p-AO/CNFs was dominated by

321

inner-sphere surface complexation in a wide range of pH. These observations

322

indicated p-AO/CNFs as a potential adsorbent to selectively enrich uranium from

323

aqueous solutions, seawater and groundwater in the cleanup of environmental

324

pollution.

325

ASSOCIATED CONTENT

326

Supporting Information

327

Complementary work that is associated with this present study is provided and

328

includes: 1) images from TGA analysis and zeta potentials, 2) details on adsorption

329

kinetics models and the Langmuir and Freundlich models, and 3) details on the batch

330

adsorption and adsorption recyclability (PDF). This material is available free of

331

charge via the Internet at http://pubs.acs.org.

332

AUTHOR INFORMATION

333

Notes

334

The authors declare no competing financial interest.

335

ACKNOWLEDGEMENTS

336

Financial support from Science Challenge Project (TZ2016004), the Research Fund

ACS Paragon Plus Environment

Page 16 of 34

Page 17 of 34

Environmental Science & Technology

337

Program of Guangdong Provincial Key Laboratory of Radionuclides Pollution

338

Control and Resources (GZDX2017K002), National Natural Science Foundation of

339

China (21577032, 2147713 and 21607156), National Key Research and Development

340

Program of China (2017YFA0207002)

341

of Radiation Medicine and Protection and the Priority Academic Program

342

Development of Jiangsu Higher Education Institutions are acknowledged.

343

REFERENCES

344

(1) Geckeis, H.; Luetzenkirchen, J.; Polly, R.; Rabung, T.; Schmidt, M.

345

Mineral-water interface reactions of actinides. Chem. Rev. 2013, 113, 1016-1062.

346

(2) Sun, Y. B.; Li, J. X.; Wang, X. K. The retention of uranium and europium onto

347

sepiolite investigated by macroscopic, spectroscopic and modeling techniques.

348

Geochim. Cosmochim. Acta 2014, 140, 621-643.

349

(3) Kowal-Fouchard, A.; Drot, R.; Simoni, E.; Ehrhardt, J. J. Use of spectroscopic

350

techniques for uranium (VI)/montmorillonite interaction modeling. Environ. Sci.

351

Technol. 2004, 38, 1399-1407.

352

(4) Sun, Y. B.; Zhang, R.; Ding, C. C.; Wang, X. X.; Cheng, W. C.; Chen, C. L.;

353

Wang, X. K. Adsorption of U(VI) on sericite in the presence of Bacillus subtilis: A

354

combined batch, EXAFS and modeling techniques. Geochim. Cosmochim. Acta 2016,

355

180, 51-65.

356

(5) van Veelen, A.; Bargar, J. R.; Law, G. T. W.; Brown, G. E.; Wogelius, R. A.

357

Uranium immobilization and nanofilm formation on magnesium rich minerals.

358

Environ. Sci. Technol. 2016, 50, 3435-3443.

359

(6) Ding, C. C.; Cheng, W. C.; Sun, Y. B.; Wang, X. K. Effects of Bacillus subtilis

360

on the reduction of U(VI) by nano-Fe0. Geochim. Cosmochim. Acta 2015, 165,

361

86-107.

362

(7) O'Loughlin, E. J.; Kelly, S. D.; Cook, R. E.; Csencsits, R.; Kemner, K. M.

and the Jiangsu Provincial Key Laboratory

ACS Paragon Plus Environment

Environmental Science & Technology

363

Reduction of uranium(VI) by mixed iron(II/iron(III) hydroxide (green rust):

364

Formation of UO2 manoparticies. Environ. Sci. Technol. 2003, 37, 721-727.

365

(8) Bargar, J. R.; Reitmeyer, R.; Lenhart, J. J.; Davis, J. A. Characterization of

366

U(VI)-carbonato ternary complexes on hematite: EXAFS and electrophoretic mobility

367

measurements. Geochim. Cosmochim. Acta 2000, 64, 2737-2749.

368

(9) Duff, M. C.; Coughlin, J. U.; Hunter, D. B. Uranium co-precipitation with iron

369

oxide minerals. Geochim. Cosmochim. Acta 2002, 66, 3533-3547.

370

(10) Mellah, A.; Chegrouche, S.; Barkat, M. The removal of uranium(VI) from

371

aqueous solutions onto activated carbon: Kinetic and thermodynamic investigations. J.

372

Colloid. Interface Sci. 2006, 296, 434-441.

373

(11) Schierz, A.; Zaenker, H. Aqueous suspensions of carbon nanotubes: Surface

374

oxidation, colloidal stability and uranium sorption. Environ. Pollut. 2009, 157,

375

1088-1094.

376

(12) Sun, Y. B.; Yang, S. B.; Chen, Y.; Ding, C. C.; Cheng, W. C.; Wang, X. K.

377

Adsorption and desorption of U(VI) on functionalized graphene oxides: A combined

378

experimental and theoretical study. Environ. Sci. Technol. 2015, 49, 4255-4262.

379

(13) Coleman, S. J.; Coronado, P. R.; Maxwell, R. S.; Reynolds, J. G. Granulated

380

activated carbon modified with hydrophobic silica aerogel-potential composite

381

materials for the removal of uranium from aqueous solutions. Environ. Sci. Technol.

382

2003, 37, 2286-2290.

383

(14) Wang, X.; Yang, S.; Shi, W.; Li, J.; Hayat, T.; Wang, X. Different interaction

384

mechanisms of Eu(III) and

385

spectroscopy technique and theoretical calculation. Environ. Sci. Technol. 2015, 49,

386

11721-11728.

387

(15) Wang, X. K.; Chen, C. L.; Hu, W. P.; Ding, A. P.; Xu, D.; Zhou, X. Carbon

388

nanotubes. Environ. Sci. Technol. 2005, 39, 2856-2860.

389

(16) Wang, X. K.; Chen, C. L.; Du, J. Z.; Tan, X. L.; Xu, D.; Yu, S. M. Effect of pH

390

and aging time on the kinetic dissociation of

243

Am(III) with carbon nanotubes studied by batch,

243

Am(III) from humic acid-coated

ACS Paragon Plus Environment

Page 18 of 34

Page 19 of 34

Environmental Science & Technology

391

gamma-Al2O3: A chelating resin exchange study. Environ. Sci. Technol. 2005, 39,

392

7084-7088.

393

(17) Popova, N. N.; Bykov, G. L.; Petukhova, G. A.; Tananaev, I. G.; Ershov, B. G.

394

Sorption of Tc(VII) and Am(III) by carbon materials: effect of oxidation. J. Radianal.

395

Nucl. Chem. 2013, 298, 1463-1468.

396

(18) Romanchuk, A. Y.; Slesarev, A. S.; Kalmykov, S. N.; Kosynkin, D. V.; Tour, J.

397

M. Graphene oxide for effective radionuclide removal. Phys. Chem. Chem. Phys.

398

2013, 15, 2321-2327.

399

(19) Xiao, N.; Zhou, Y.; Ling, Z.; Qiu, J. S. Synthesis of a carbon nanofiber/carbon

400

foam composite from coal liquefaction residue for the separation of oil and water.

401

Carbon 2013, 59, 530-536.

402

(20) Wu, Z. Y.; Li, C.; Liang, H. W.; Zhang, Y. N.; Wang, X.; Chen, J. F.; Yu, S. H.

403

Carbon nanofiber aerogels for emergent cleanup of oil spillage and chemical leakage

404

under harsh conditions. Sci. Rep. 2014, 4, 4079-6.

405

(21) Tai, M. H.; Tan, B. Y. L.; Juay, J.; Sun, D. D.; Leckie, J. O. A self-assembled

406

superhydrophobic electrospun carbon-silica nanofiber sponge for selective removal

407

and recovery of oils and organic solvents. Chem. Eur. J. 2015, 21, 5395-5402.

408

(22) Salehi, M.; Krishnamurthy, A.; Forster, A. M.; Hsiao, K. T.; Whelton, A. J.

409

Polyester composite water uptake and organic contaminant release affected by carbon

410

nanofiber reinforcements. J. Appl. Poly. Sci. 2016, 133.

411

(23) Peter, K. T.; Vargo, J. D.; Rupasinghe, T. P.; De Jesus, A.; Tivanski, A. V.;

412

Sander, E. A.; Myung, N. V.; Cwiertny, D. M. Synthesis, optimization, and

413

performance demonstration of electrospun carbon nanofiber-carbon nanotube

414

composite sorbents for point-of-use water treatment. ACS Appl. Mater. Interface 2016,

415

8, 11431-11440.

416

(24) Liang, H. W.; Guan, Q. F.; Chen, L. F.; Zhu, Z.; Zhang, W. J.; Yu, S. H.

417

Macroscopic-scale template synthesis of robust carbonaceous nanofiber hydrogels and

418

aerogels and their applications. Angew. Chem. Int. Ed. 2012, 51, 5101-5105.

ACS Paragon Plus Environment

Environmental Science & Technology

419

(25) Ding, C. C.; Cheng, W. C.; Wang, X. X.; Wu, Z.-Y.; Sun, Y. B.; Chen, C. L.;

420

Wang, X. K.; Yu, S.-H. Competitive sorption of Pb(II), Cu(II) and Ni(II) on

421

carbonaceous nanofibers: a spectroscopic and modeling approach. J. Hazard. Mater.

422

2016, 313, 253-261.

423

(26)Cheng, W. C.; Ding, C. C.; Wang, X. X.; Wu, Z.-Y.; Sun, Y. B.; Yu, S.-H.; Hayat,

424

T.; Wang, X. K. Competitive sorption of As(V) and Cr(VI) on carbonaceous

425

nanofibers. Chem. Eng. J. 2016, 293, 311-318.

426

(27) Sun, Y. B.; Wang, X. X.; Ding, C. C.; Cheng, W. C.; Chen, C. L.; Hayat, T.;

427

Alsaedi, A.; Hu, J.; Wang, X. K. Direct syntheis of bacteria-derived carbonaceous

428

nanofibers as a highly efficient material for radionucides elimination. ACS

429

Sustainable Chem. Eng. 2016, 4, 4608-4616.

430

(28) Zhang, R.; Chen, C. L.; Li, J.; Wang, X. K. Investigation of interaction between

431

U(VI) and carbonaceous nanofibers by batch experiments and modeling study. J.

432

Colloid. Interface Sci. 2015, 460, 237-246.

433

(29)Sun, Y. B.; Wu, Z.-Y.; Wang, X. X.; Ding, C. C.; Cheng, W. C.; Yu, S.-H.; Wang,

434

X. K. Macroscopic and microscopic investigation of U(VI) and Eu(III) adsorption on

435

carbonaceous nanofibers. Environ. Sci. Technol. 2016, 50, 4459-4467.

436

(30) Liang, H. W.; Cao, X.; Zhang, W. J.; Lin, H. T.; Zhou, F.; Chen, L. F.; Yu, S. H.

437

Robust and highly efficient free-standing carbonaceous nanofiber membranes for

438

water purification. Adv. Funct. Mater. 2011, 21, 3851-3858.

439

(31) Barber, P. S.; Kelley, S. P.; Rogers, R. D. Highly selective extraction of the

440

uranyl ion with hydrophobic amidoxime-functionalized ionic liquids via eta(2)

441

coordination. RSC Adv. 2012, 2, 8526-8530.

442

(32) Das, S.; Pandey, A. K.; Athawale, A. A.; Manchanda, V. K. Exchanges of

443

uranium(VI) species in amidoxime-functionalized sorbents. J. Phys. Chem. B 2009,

444

113, 6328-6335.

445

(33) Omichi, H.; Katakai, A.; Sugo, T.; Okamoto, J. A new type of

446

amidoxime-group-containing adsorbent for the recovery of uranium from seawater 2.

ACS Paragon Plus Environment

Page 20 of 34

Page 21 of 34

Environmental Science & Technology

447

Effect of grafting of hydrophilic monomers. Sep. Sci. Technol. 1986, 21, 299-313.

448

(34) Saito,

449

amidoxime-group-containing membrane for the recovery of uranium from seawater.

450

Ind. Eng. Chem. Res. 1987, 26, 1977-1981.

451

(35) Sekiguchi, K.; Saito, K.; Konishi, S.; Furusaki, S.; Sugo, T.; Nobukawa, H. Effect

452

of seawater temperature on uranium recovery from seawater using amidoxime

453

adsorbents. Ind. Eng. Chem. Res. 1994, 33, 662-666.

454

(36) Zhang, L. J.; Su, J.; Yang, S. T.; Guo, X. J.; Jia, Y. P.; Chen, N.; Zhou, J.; Zhang,

455

S.; Wang, S.; Li, J.; Li, J. Y.; Wu, G. Z.; Wang, J. Q. Extended X-ray absorption fine

456

structure and density functional theory studies on the complexation mechanism of

457

amidoximate ligand to uranyl carbonate. Ind. Eng. Chem. Res. 2016, 55, 4224-4230.

458

(37)Sun, Y. B.; Yang, S. T.; Sheng, G. D.; Guo, Z. Q.; Tan, X. L.; Xu, J. Z.; Wang, X.

459

K. Comparison of U(VI) removal from contaminated groundwater by nanoporous

460

alumina and non-nanoporous alumina. Sep. Purif. Technol. 2011, 83, 196-203.

461

(38) Shao, D. D.; Jiang, Z. Q.; Wang, X. K.; Li, J. X.; Meng, Y. D. Plasma induced

462

grafting carboxymethyl cellulose on multiwalled carbon nanotubes for the removal of

463

UO22+ from aqueous solution. J. Phys. Chem. B 2009, 113, 860-864.

464

(39) Hu, J.; Shao, D. D.; Chen, C. L.; Sheng, G. D.; Li, J. X.; Wang, X. K.; Nagatsu,

465

M. Plasma-induced grafting of cyclodextrin onto multiwall carbon nanotube/iron

466

oxides for adsorbent application. J. Phys. Chem. B 2010, 114, 6779-6785.

467

(40) Jiang, N.; Lu, N.; Shang, K. F.; Li, J.; Wu, Y. Innovative approach for benzene

468

degradation using hybrid surface/packed-bed discharge plasmas. Environ. Sci.

469

Technol. 2013, 47, 9898-9903.

470

(41) Wu, Z. Y.; Li, C.; Liang, H. W.; Chen, J. F.; Yu, S. H. Ultralight, flexible, and

471

fire-resistant carbon nanofiber aerogels from bacterial cellulose. Angew. Chem. Int.

472

Ed. 2013, 52, 2925-2929.

473

(42) Zeng, Z. H.; Wei, Y. Q.; Shen, L.; Hua, D. B. Cationically charged

474

poly(amidoxime)-grafted polypropylene nonwoven fabric for potential uranium

K.;

Hori,

T.;

Furusaki,

S.;

Sugo,

T.;

ACS Paragon Plus Environment

Okamoto,

J.

Porous

Environmental Science & Technology

Page 22 of 34

475

extraction from seawater. Ind. Eng. Chem. Res. 2015, 54, 8699-8705.

476

(43) Ravel, B.; Newville, M. ATHENA, ARTEMIS, HEPHAESTUS: data analysis for

477

X-ray absorption spectroscopy using IFEFFIT. J. Synchrotron. Rad. 2005, 12,

478

537-541.

479

(44) Wyckoff, R. W. G. Fluorite structure. In crystal structures, seconded. John Wiley

480

Interscience Publishers: New York 1963, 1, pp 239-444.

481

(45) Maldonado, S.; Stevenson, K. J. Influence of nitrogen doping on oxygen

482

reduction electrocatalysis at carbon nanofiber electrodes. J. Phys. Chem. B 2005, 109,

483

4707-4716.

484

(46) Basarir, S. S.; Bayramgil, N. P. The uranium recovery from aqueous solutions

485

using

486

hydroxypropylmethylcellulose with amidoxime groups. Cellulose 2013, 20,

487

1511-1522.

488

(47) Ding, C. C.; Cheng, W. C.; Sun, Y. B.; Wang, X. K. Determination of chemical

489

affinity of graphene oxide nanosheets with radionuclides investigated by macroscopic,

490

spectroscopic and modeling techniques. Dalton Trans. 2014, 43, 3888-3896.

491

(48) Sun, Y. B.; Wang, X. X.; Song, W. C.; Lu, S. H.; Chen, C. L.; Wang, X. K.

492

Mechanistic insights into the decontamination of Th(IV) on graphene oxide-based

493

composites by EXAFS and modeling techniques. Envrion. Sci.: Nano 2017, 4,

494

222-232.

495

(49) Cheng, W. C.; Ding, C. C.; Sun, Y. B.; Wang, X. K. Fabrication of

496

fungus/attapulgite composites and their removal of U(VI) from aqueous solution.

497

Chem. Eng. J. 2015, 269, 1-8.

498

(50) Hayes, K. F.; Papelis, C.; Leckie, J. O. Modeling ionic-strength effect on anion

499

adsorption at hydrous oxide solution interfaces. J. Colloid. Interface Sci. 1988, 125,

500

717-726.

501

(51) McBride, M. B. A critique of diffuse double layer models applied to colloid and

502

surface chemistry. Clays Clay Miner. 1997, 45, 598-608.

amidoxime

modified

cellulose

derivatives.

ACS Paragon Plus Environment

III.

Modification

of

Page 23 of 34

Environmental Science & Technology

503

(52) Jin, Z. X.; Wang, X. X.; Sun, Y. B.; Ai, Y. J.; Wang, X. K. Adsorption of

504

4-n-nonylphenol and bisphenol-A on magnetic reduced graphene oxides: A combined

505

experimental and theoretical studies. Environ. Sci. Technol. 2015, 49, 9168-9175.

506

(53) Singh, K.; Shah, C.; Dwivedi, C.; Kumar, M.; Bajaj, P. N. Study of uranium

507

adsorption using amidoximated polyacrylonitrile-encapsulated macroporous beads. J.

508

Appl. Poly. Sci. 2013, 127, 410-419.

509

(54) Gorka, J.; Mayes, R. T.; Baggetto, L.; Veith, G. M.; Dai, S. Sonochemical

510

functionalization of mesoporous carbon for uranium extraction from seawater. J.

511

Mater. Chem. A 2013, 1, 3016-3026.

512

(55) James, D.; Venkateswaran, G.; Rao, T. P. Removal of uranium from mining

513

industry feed simulant solutions using trapped amidoxime functionality within a

514

mesoporous imprinted polymer material. Microp. Mesop. Mater. 2009, 119, 165-170.

515

(56) Zhang, A. Y.; Uchiyama, G.; Asakura, T. pH Effect on the uranium adsorption

516

from seawater by a macroporous fibrous polymeric material containing amidoxime

517

chelating functional group. React. Funct. Polymer. 2005, 63, 143-153.

518

(57) Wang, Y.; Gu, Z. X.; Yang, J. J.; Liao, J. L.; Yang, Y. Y.; Liu, N.; Tang, J.

519

Amidoxime-grafted multiwalled carbon nanotubes by plasma techniques for efficient

520

removal of uranium(VI). Appl. Surface Sci. 2014, 320, 10-20.

521

(58)Das, S.; Pandey, A. K.; Athawale, A.; Kumar, V.; Bhardwaj, Y. K.; Sabharwal, S.;

522

Manchanda, V. K. Chemical aspects of uranium recovery from seawater by

523

amidoximated electron-beam-grafted polypropylene membranes. Desalination 2008,

524

232, 243-253.

525

(59) Mane, G. P.; Talapaneni, S. N.; Anand, C.; Varghese, S.; Iwai, H.; Ji, Q. M.;

526

Ariga, K.; Mori, T.; Vinu, A. Preparation of highly ordered nitrogen-containing

527

mesoporous carbon from a gelatin biomolecule and its excellent sensing of acetic acid.

528

Adv. Funct. Mater. 2012, 22, 3596-3604.

529

(60) Sun, Y. B.; Shao, D. D.; Chen, C. L.; Yang, S. B.; Wang, X. K. Highly efficient

530

enrichment of radionuclides on graphene oxide-supported polyaniline. Environ. Sci.

ACS Paragon Plus Environment

Environmental Science & Technology

531

Technol. 2013, 47, 9904-9910.

532

(61) Liu, H.; Zhu, Y.; Xu, B.; Li, P.; Sun, Y.; Chen, T. Mechanical investigation of

533

U(VI) on pyrrhotite by batch, EXAFS and modeling techniques. J. Hazard. Mater.

534

2017, 322, Part B, 488-498.

535

(62) Sun, Y. B.; Wang, Q.; Chen, C. L.; Tan, X. L.; Wang, X. K. Interaction between

536

Eu(III) and graphene oxide nanosheets investigated by batch and extended X-ray

537

absorption fine structure spectroscopy and by modeling techniques. Environ. Sci.

538

Technol. 2012, 46, 6020-6027.

539

ACS Paragon Plus Environment

Page 24 of 34

Page 25 of 34

Environmental Science & Technology

540

Figure Captions

541

Figure 1. Characterization of two kinds of AO/CNFs, A and B: SEM images of p-

542

and c-AO/CNFs, respectively; C: FT-IR spectra; D: high-resolution N 1s XPS spectra.

543

Figure 2. Adsorption kinetics (A) and pH effect (B) of

544

adsorption onto two kinds of AO/CNFs, C0 = 10.0 mg/L, I = 0.01 mol/L NaCl, m/v=

545

0.6 g/L, pH = 3.5, T = 293 K.

546

Figure 3. A: Adsorption isotherms of U(VI) on two kinds of AO/CNFs, I = 0.01

547

mol/L NaCl, m/v= 0.6 g/L, pH = 3.5, T = 293 K; B: Comparison of adsorption of

548

U(VI) on p-AO/CNFs with Th(IV), Eu(III), Am(III), Sr(II), Co(II), Ni(II) and Cs(I), I

549

= 0.01 mol/L NaCl, m/v = 0.6 g/L, T = 293 K.

550

Figure 4. XPS analysis of adsorption and desorption of U(VI) on p-AO/CNFs, A:

551

survey scans; B-D: high resolution of O 1s, N 1s and U 4f after U(VI) adsorption and

552

desorption, respectively, C0 = 10.0 mg/L, I = 0.01 mol/L NaCl, m/v= 0.6 g/L, pH =

553

3.5, T = 293 K.

554

Figure 5. The k2-weighted U LIII-edge EXAFS spectra (A) and corresponding Fourier

555

Transmission (FT) (B) of references and U(VI) adsorption samples, C0 = 10 mg/L,

556

m/v = 0.6 g/L, I = 0.01 mol/L NaCl, T = 293 K.

557

Figure 6. Surface complexation modeling of 238U(VI) adsorption on c- (A and B) and

558

p-AO/CNFs (C and D), A and C: pH effect, B and D: adsorption isotherm, C0 = 10.0

559

mg/L, I = 0.01 mol/L NaCl, m/v= 0.6 g/L, T = 293 K.

ACS Paragon Plus Environment

238

U(VI) and

241

Am(III)

Environmental Science & Technology

Page 26 of 34

(B)

(A)

(C)

C-N

N-O

p-AO/CNFs

C=N

c-AO/CNFs O-H/N-H(3400)

C-N(1290) C=N (1500) C=C(1655)

N-O(935)

(D)

p-AO/CNFs

c-AO/CNFs

600 900 1200 1500 1800 2100 2400 2700 3000 3300 3600

Wavenumber (cm-1)

398

399

400

401

402

Binding energy (eV)

Figure 1

ACS Paragon Plus Environment

403

Page 27 of 34

Environmental Science & Technology

100 (B)

(A)

90

90

80

238

70

238

60

241

U(VI)+p-AO/CNFs U(VI)+c-AO/CNFs Am(III)+p-AO/CNFs

241

Am(III)+c-AO/CNFs

50 40 30 20 10

Amount of adsorbed radionuclides (%)

Amount of adsorbed radionuclides (%)

100

80 70 60 50 40 30

238

U(VI)+p-AO/CNFs

238

20

U(VI)+c-AO/CNFs

241

Am(III)+p-AO/CNFs

10

0

241

Am(III)+c-AO/CNFs

0

0

3

6

9

12

15

Reaction time (h)

18

21

24

1

2

3

4

Figure 2

ACS Paragon Plus Environment

5pH 6

7

8

9

10

Environmental Science & Technology

(A)

Page 28 of 34

(B)

600

450 400

500 238

U(VI)+p-AO/CNFs(aqueous solution) U(VI)+c-AO/CNFs(aqueous solution) 238 U(VI)+p-AO/CNFs(seawater) 238 U(VI)+c-AO/CNFs(seawater)

Qe (mg/g)

Qe (mg/g)

350

238

300 250 200 150

400

300

200

100 100

50 0 0

1

2

3

4

5

6

0

Ce (mg/L)

U(VI) Th(IV) Eu(III) Am(III) Sr(II) Ni(II) Co(II) Cs(I)

Figure 3

ACS Paragon Plus Environment

Page 29 of 34

Environmental Science & Technology

O 1s

(A)

(B)

C 1s

p-AO/CNFs_UD

U 4f N 1s

p-AO/CNFs_UD p-AO/CNFs_UA

p-AO/CNFs_UA p-AO/CNFs C-O

p-AO/CNFs

200

400

600

800

adsorbed H2O

C=O -OH

1000

530

531

532

533

534

535

(C)

(D) C-C C=N

C-N/C-O

p-AO/CNFs_UD C=O

p-AO/CNFs_UD

p-AO/CNFs_UA

p-AO/CNFs_UA 282

283

284

285

286

287

288

289

290

291

378

Binding energies (eV)

380

382

384

386

388

390

Binding energies (eV)

Figure 4

ACS Paragon Plus Environment

392

394

396

Environmental Science & Technology

(B)

U -O ax

(A)

Page 30 of 34

U-C U-U

U-Oeq

UO2CO3(s)

UO2CO (s) 3

2

FT(Κ χ)

2

χ(κ)κ

p-AO/CNFs

p-AO/CNFs

c-AO/CNFs c-AO/CNFs

3

4

5

o -1

k(A)

6

7

8

0

1

2

Figure 5

ACS Paragon Plus Environment

30

R(A)

4

5

6

Environmental Science & Technology

(B) 480

100 (A) 90 80 70 60 50 40 30 20 10 0 100 (C) 90 80 70 60 50 40 30 20 10 0

Qe (mg/g)

400 320

SO(UO2)3(OH)72-

240 160

SOUO2+

SOUO2+ SOUO2(CO3)23-

80

2SOUO2(CO3)23- SO(UO2)3(OH)7

0 (D) 480 400 SOUO2+

SO(UO2)3(OH)72-

320

Qe (mg/g)

Amount of adsorbed U(VI) (%)

Amount of adsorbed U(VI) (%)

Page 31 of 34

240 SOUO2+

160

SOUO2(CO3)23-

SO(UO2)3(OH)72-

80

SOUO2(CO3)232

3

4

5

6

7

8

0

1

2

pH

Figure 6

ACS Paragon Plus Environment

3 4 Ce (mg/L)

5

0 6

Environmental Science & Technology

Page 32 of 34

Table 1. Selective Properties of Two Kinds of AO/CNFs Samples

SBET (m2/g)

Zeta potential

N content (at %)

c-AO/CNFs

154.5

0 eV at pH 2.01

4.26

p-AO/CNFs

139.7

0 eV at pH 2.45

6.57

Table 2. Comparison of Adsorption Capacity of U(VI) on Various AmidoximeContaining Adsorbents Sorbents

Capacity (mg/g)

Ref.

AO/ macroporous beads

3.5

[53]

AO/mesoporous carbon

4.6

[54]

AO/mesoporous imprinted polymer

19.1

[55]

44

[56]

145

[57]

AO/polypropylene membranes

380.0

[58]

p-AO/CNFs

588.2

This study

AO/poly(propylene) fibrous AO/multiwalled carbon nanotubes

ACS Paragon Plus Environment

Page 33 of 34

Environmental Science & Technology

Table 3. EXAFS Results of Reference and U(VI)-Containing Samples at LIII-Edge, T = 293 K, I = 0.01 mol/L NaCl Solution Samples

Shell

R (Å)a

CN b

σ2(Å2) c

UO2CO3(s)

U-Oax

1.785

2.0

0.0031

U-Oeq

2.564

5.2

0.0068

U-C

2.894

1.6

0.0056

U-U

3.816

0.4

0.0087

U-Oax

1.789

2.0

0.0042

U-Oeq

2.517

4.7

0.0065

U-C

2.901

1.5

0.0071

U-Oax

1.804

2.0

0.0022

U-Oeq

2.526

5.1

0.0064

U-C

2.921

1.7

0.0082

p-AO/CNFs

c-AO/CNFs

a

R: bond length; b CN: coordination numbers; c σ2: Debye-Waller factor

Table 4. Optimized Parameters of Surface Complexation Modeling for U(VI) Adsorption on c-(1) and p-AO/CNFs (2) Reactions

Log K (1)

(2)

SOH + H+ = SOH2+

3.54

3.27

SOH = SO- + H+

-5.26

-6.59

SOH + UO22+ = SOUO2+ +H+

2.61

2.97

SOH + 3UO22+ +7H2O = SO(UO2)3(OH)72- + 8H+

-2.65

-3.01

SOH + UO22+ +2CO32- = SOUO2(CO3)23- + H+

-8.09

-8.67

ACS Paragon Plus Environment

Environmental Science & Technology

TOC

PLASM

CN

.

NH2OH HCl

AO/CNF

ACS Paragon Plus Environment

Page 34 of 34