Characteristics of Back Corona Discharge in a ... - ACS Publications

May 5, 2015 - and Its Application for Treatment of Volatile Organic Compounds. Fada Feng,. †,‡ ... this system allowed back corona discharge (BCD)...
0 downloads 0 Views 2MB Size
Subscriber access provided by UB + Fachbibliothek Chemie | (FU-Bibliothekssystem)

Article

Characteristics of back corona discharge in a honeycomb catalyst and its application for treatment of volatile organic compounds Fada Feng, Yanyan Zheng, Xinjun Shen, Qinzhen Zheng, Shaolong Dai, Xuming Zhang, Yifan Huang, Zhen Liu, and keping yan Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.5b00447 • Publication Date (Web): 05 May 2015 Downloaded from http://pubs.acs.org on May 10, 2015

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 25

Environmental Science & Technology

1

Characteristics of back corona discharge in a honeycomb catalyst and

2

its application for treatment of volatile organic compounds

3

Fada Feng1,2, Yanyan Zheng1, Xinjun Shen1, Qinzhen Zheng1, Shaolong Dai1, Xuming

4

Zhang1, Yifan Huang1*, Zhen Liu1, Keping Yan1

5

1. Key Laboratory of Biomass Chemical Engineering of Ministry of Education,

6

College of Chemical and Biological Engineering, Zhejiang University, Hangzhou

7

310007, People’s Republic of China

8 9

2. School of Chemistry and Environment, Jiaying University, Meizhou 514015, People’s Republic of China

10

Abstract: The main technical challenges for the treatment of volatile organic

11

compounds (VOCs) with plasma-assisted catalysis in industrial applications are large

12

volume plasma generation under atmospheric pressure, by-product control, and

13

aerosol collection. To solve these problems, a back corona discharge (BCD)

14

configuration has been designed to evenly generate non-thermal plasma in a

15

honeycomb catalyst. Voltage-current curves, discharge images, and emission spectra

16

have been used to characterize the plasma. Grade particle collection results and flow

17

field visualization in the discharge zones show not only that the particles can be

18

collected efficiently, but also that the pressure drop of the catalyst layer is relatively

19

low. A three-stage plasma-assisted catalysis system, comprising a dielectric barrier

20

discharge (DBD) stage, BCD stage, and catalyst stage, was built to evaluate toluene

21

treatment performance by BCD. The ozone analysis results indicate that BCD 1

ACS Paragon Plus Environment

Environmental Science & Technology

22

enhances the ozone decomposition by collecting aerosols and protecting the Ag-Mn-O

23

catalyst downstream from aerosol contamination. The GC and FTIR results show that

24

BCD contributes to toluene removal, especially when the specific energy input is low,

25

and the total removal efficiency reaches almost 100%. Furthermore, this removal

26

results in the emission of fewer by-products.

27

TOC Art

28 29

1 Introduction

30

It is proposed that the future applications for plasma-assisted catalysis will most

31

likely be in the treatment of gaseous waste1-4 and in the use of plasma to prepare and

32

modify catalysts5-6. In conventional catalysis, the required activation energy for

33

reactions is supplied in the form of heat, while in plasma-assisted catalysis, the catalyst

34

can be activated directly by plasma, in which only the electrons are energized, and the

35

bulk gas is not significantly heated7. Therefore, the key requirement for these systems

36

is plasma-induced activation of the catalyst at relatively low temperatures. Besides, 2

ACS Paragon Plus Environment

Page 2 of 25

Page 3 of 25

Environmental Science & Technology

37

plasma-assisted catalysis has the potential to enhance global reaction rates, improve

38

reaction selectivity, and increase energy efficiency2. Most of the researches in this field

39

mainly focus on plasma generation8, plasma activation of catalysts9, configuration of

40

plasma combined with catalysts10,11, by-product generation and control12, mechanism

41

of synergistic effects13-16, and reaction kinetics17. Plasma-assisted catalysis for the

42

treatment of VOCs has been studied over two decades, and several excellent reviews

43

have been published in recent years1-3,9,18,19. However, several technical challenges

44

still remain before large-scale industrial application of plasma-assisted catalysis can

45

become practical. Understanding the complex mechanism of synergistic effects and

46

elucidation of the decomposition roadmap of VOCs are widely acknowledged

47

examples of these challenges, but problems associated with large volume plasma

48

generation under atmospheric pressure, by-product control, and aerosol collection

49

must also be addressed.

50

In a one-stage plasma-catalysis configuration such as that seen in a packed-bed

51

reactor, the catalyst is placed in the discharge zone. This allows for a significant

52

synergistic effect, but the relatively high-pressure drop across the catalyst layer is

53

problematic. Employing a honeycomb structured catalyst is a way to lessen the

54

pressure drop, but generating plasma evenly in a honeycomb is difficult. In this work,

55

a hybrid honeycomb configuration comprising a packed bed and capillaries has been

56

used to generate a discharge so that a larger surface area can be obtained with a lower

57

pressure drop20,21. It was also found that this system allowed back corona discharge 3

ACS Paragon Plus Environment

Environmental Science & Technology

58

(BCD) to be successfully employed22-24, which represents an effective method for

59

non-thermal plasma generation and a synergistic plasma catalysis effect25-28. Our

60

research has demonstrated that BCD not only has the potential to activate the catalyst,

61

but also has a further advantage in that aerosols, the major by-product of VOC

62

treatment by the plasma method, can be captured on the catalyst surface and broken

63

down into CO2 and H2O by plasma and catalytic oxidation26. BCD can be easily

64

induced using normal high-voltage DC power sources, which are very reliable and

65

inexpensive, and therefore, it has the potential for application in industrial-scale VOC

66

treatment.

67

In this paper, a BCD reactor capable of evenly generating plasma in a

68

honeycomb catalyst is described. The plasma produced is characterized by reference

69

to voltage-current curves, discharge images, and emission spectra. Grade particle

70

collection efficiency and flow field visualization in the discharge zones are also

71

investigated to gain further understanding of BCD. A three-stage plasma-assisted

72

catalysis system, comprising DBD, BCD, and catalyst, is proposed to evaluate the

73

BCD performance using toluene as a sample VOC. Since DBD is an ideal method to

74

generate ozone that can be used to decompose VOCs29, a DBD is applied in the first

75

stage of the hybrid reactor to generate a high concentration of ozone and partially

76

decompose the toluene. In the second stage, a BCD collects and decomposes the

77

aerosols produced by the DBD, which has the dual purpose of removing aerosol

78

pollution and promoting the treatment in the following catalytic stage. The 4

ACS Paragon Plus Environment

Page 4 of 25

Page 5 of 25

Environmental Science & Technology

79

performance of BCD for ozone generation and decomposition are also described.

80

Finally, the total removal efficiency and product composition are discussed in order to

81

evaluate the hybrid plasma-assisted catalysis method.

82

2 Experimental Section

83

Figure 1(a) shows the experimental setup used in this work, in which the reactor can

84

be regarded as the BCD reactor alone (Figure 1(b)) for plasma characterization,

85

particle collection measurement, and flow field visualization, or as the full three-stage

86

plasma-assisted catalysis system (Figure 1(c)) for toluene decomposition. The

87

experimental setups of particle collection measurement and flow field visualization

88

are described in S1 and S2 of Supporting Information, respectively. As shown in

89

Figure 1(b), the main BCD reactor is arranged in a needles-mesh-honeycomb-mesh

90

configuration. The distance between the needle electrodes and middle mesh, and the

91

middle mesh and bottom mesh is 16 mm and 14 mm, respectively. The discharge

92

electrode is a stainless steel needle with a tip radius of about 0.25 mm, and the mesh is

93

made of nickel foam with a pore density of 110 pores per inch (PPI). The Ag-Mn-O

94

catalyst supported on the honeycomb for BCD generation is prepared by

95

oxidoreduction precipitation. A 400 cell/in2 mesh alumina honeycomb support with a

96

diameter of 100 mm and a thickness of 10 mm was coated with a mixture of Ag-Mn-O

97

and alumina gel, and then calcined at 723 K in air for 4 h. The BCD reactor is placed in

98

a quartz tube with an inner diameter of 120 mm and powered by a negative high-

99

voltage DC power supply. 5

ACS Paragon Plus Environment

Environmental Science & Technology

100

Figure 1(c) shows a schematic diagram of the three-stage plasma-assisted

101

catalysis system, comprising DBD, BCD, and catalyst. The DBD reactor consists of 12

102

cylindrical quartz tubes of around 7 mm inner diameter, 1 mm wall thickness, and 20

103

cm length wrapped in a high-voltage electrode made of copper mesh. Each quartz tube

104

is mounted inside a stainless steel rod to form annular discharge gaps of about 1 mm

105

radial width. The DBD reactor is driven by an AC power source at a frequency of 50 Hz

106

and peak voltage of ±11 kV. In the BCD stage, the configuration is the same as in

107

Figure 1(b). For the catalyst stage, a 400-mesh honeycomb alumina support of 100

108

mm diameter and 20 mm thickness supports 2 g of Ag-Mn-O catalyst. The Ag-Mn-O

109

catalyst here is prepared by a previously described impregnation method26,30. The

110

toluene decomposition experiment was carried out in air with a relative humidity of

111

around 10% at atmospheric pressure and ambient temperature (around 293 K). The

112

initial concentration of toluene was 100 ppm, and the total gas flow rate was 5 L/min.

113

The total discharge volume was around 27.1 cm3, which corresponds to a residence

114

time of 0.33 s. The details of the instruments for electric measurement and gas

115

composition measurement can be found in S3 of Supporting Information. The

116

definitions of toluene removal efficiency, CO selectivity, CO2 selectivity and carbon

117

balance, specific input energy (SIE) and BCD discharge current density are also

118

described in S4 of Supporting Information.

6

ACS Paragon Plus Environment

Page 6 of 25

Page 7 of 25

Environmental Science & Technology

119 120

Figure 1. (a) Schematic diagram of our experimental setup; (b) BCD reactor and (c)

121

hybrid plasma-assisted catalyst for toluene decomposition.

122

3 Results and Discussion

123

BCD discharge images

124

Figure 2 shows the images of the discharge zones for two BCD configurations:

125

needle-mesh-honeycomb-mesh and needle-mesh-capillary quartz tube mesh. Figure

126

2(a) corresponds to the reactor depicted in Figure 1(b). A negative corona discharge

127

and BCD-induced streamers can be observed in the zones near the needle electrodes

128

and between the middle mesh and honeycomb catalyst surface, respectively. To enable 7

ACS Paragon Plus Environment

Environmental Science & Technology

129

visual observation of the discharges inside the honeycomb channels, a bundle of quartz

130

capillaries were used in place of the honeycomb (as shown in Figure 2(b)). The image

131

shows that the plasma is evenly distributed inside the channels of the quartz capillaries.

132

For the similar discharge configuration, it is believed that plasma can also be

133

produced evenly inside the honeycomb channels where the catalysts are supported

134 135

Figure 2. Images of the discharge zones for two BCD configurations: (a)

136

Needle-mesh-honeycomb-mesh (corresponds to the configuration shown in Figure

137

1(b); applied voltage: 30 kV; current density: 11.4 µA/cm2), and (b)

138

needle-mesh-capillary quartz tube mesh (channel diameter: 0.8 mm; applied voltage:

139

26 kV; current density: 6.2 µA/cm2).

140

Voltage-current curves

141

Figure 3 shows the voltage-current curves for BCD and typical corona discharge,

142

in which the discharge occurs at the high-voltage electrode tips without the floated 8

ACS Paragon Plus Environment

Page 8 of 25

Page 9 of 25

Environmental Science & Technology

143

mesh and honeycomb placed downstream. Before BCD occurs, the discharge current is

144

low due to charge accumulation on the honeycomb, which serves as a dielectric layer.

145

The discharge current increases significantly after BCD occurs. When the applied

146

voltage is 30 kV, the discharge current is about 358 µA, which is twice that of a typical

147

corona discharge. This is attributed to the large volume of plasma produced by BCD

148

inside the honeycomb channels.

149 150

Figure 3. Voltage-current curves of normal corona discharge and BCD with a

151

honeycomb.

152

Emission spectra

153

In order to characterize the active species and energy level of the discharges, the

154

emission spectra of the discharge between the middle mesh and the honeycomb surface,

155

as well as the BCD in the honeycomb channels, were measured. The results are shown

156

in Figure 4. Strong emission lines of the second positive system of N2 in the discharge

157

zone were observed at 337.13 nm, 357.69 nm, and 380.49 nm. These lines are similar

158

to those observed in BCD on a fly ash layer31. The emission spectrum from O3

159

(315.61 nm and 336.52 nm, 1B2–X1A1)32-34 can also be observed in this discharge 9

ACS Paragon Plus Environment

Environmental Science & Technology

160

zone. As shown in Figure 4(b), the emission intensity from the honeycomb channels

161

is relatively low, because less light can cross the narrow channels. The emission

162

spectrum of OH (A2Σ → X2Π, (0−0)) is obscured by the emission spectrum of the ∆v

163

= +1 vibration transition band of N2 (C3Πu → B3Πg)31,32,35. Additionally, more

164

reactive radicals such as OH, O, and O3 are produced due to BCD inside the

165

honeycomb channels.

166 167

Figure 4. Emission spectra of the (a) streamer discharge between the middle mesh

168

and the catalyst surface, and (b) BCD in the honeycomb channels. Applied voltage, 30

169

kV; discharge current, 358 µA.

170

Particle collection from BCD

171

In an electrostatic precipitator, BCD is a detrimental phenomenon that decreases the

172

particle collection efficiency36. Fly ash particles collected on the plate will be

173

spattered from the layer and reenter the gas flow when BCD occurs23,24,37. In the

174

treatment of VOCs with BCD, organic aerosols, the major by-product, can adhere to

175

the surface of the catalyst and be decomposed by the plasma-assisted catalysis

176

process26. Figure 5 shows the effect of BCD on the grade collection efficiency of fly 10

ACS Paragon Plus Environment

Page 10 of 25

Page 11 of 25

Environmental Science & Technology

177

ash samples. The initial total particle concentration was 30.9 mg/m3. When BCD

178

occurs, the concentration downstream decreases to 1.86 mg/m3, and the total particle

179

weight removal efficiency is about 94%. It is apparent that most of the particles in the

180

gas phase are collected in the honeycomb, especially the particles with diameters

181

under 1 µm, which matches the diameter range of aerosol particles generated by

182

toluene decomposition with non-thermal plasma, as reported in our previous work38.

183 184

Figure 5. Fine particle collection in the BCD reactor. Applied voltage, 30 kV;

185

discharge current, 358 µA; initial total particle concentration, 30.9 mg/m3; gas flow

186

rate, 10 L/min. The line with solid square points represents the grade weight

187

concentration distribution without BCD. The lines with solid triangle points and soft

188

diamond points represent grade weight concentration downstream and the

189

corresponding grade collection efficiency with BCD, respectively.

190

Flow field distribution

191

The PIV method was used for instantaneous measurement of velocity field

192

distribution without any disturbance to the flow39,40. Figure 6 shows the images of the

193

flow field inside the BCD reactor. Three conditions, i.e., (a) no particles, (b) particles 11

ACS Paragon Plus Environment

Environmental Science & Technology

194

with no discharge, and (c) particles with BCD, are compared. For no discharge, the

195

gas flow is a laminar flow, while intense turbulence with a peak velocity of around 2

196

m/s is generated when BCD occurs. As shown in Figure 6(c), moxa smoke particles

197

are treated by the honeycomb as the area below it is dark, which indicates fewer

198

particles in that area. As the diameter of moxa smoke particles is close to that of the

199

aerosols generated by non-thermal plasma, it can be concluded that the aerosols can

200

also be efficiently treated by BCD. Figure 6(d) shows velocity field distribution

201

averaged over 20 images, and indicates a distinct secondary flow that moves from the

202

needle electrodes toward the honeycomb surface and then passes through the channels.

203

The velocities of the secondary flow upstream and downstream of the honeycomb are

204

around 1–2 m/s and 0.6 m/s, respectively. Compared with other works20,21, it is

205

apparent that the pressure drop of the catalyst bed in this BCD reactor is quite small.

206

The simulation result with computational fluid dynamics software indicates that the

207

pressure drop is around 6 Pa.

12

ACS Paragon Plus Environment

Page 12 of 25

Page 13 of 25

Environmental Science & Technology

208 209

Figure 6. Images of the flow field inside the BCD reactor, (a) with no particles, (b)

210

with particles but no discharge, and (c) particles with BCD. Image (d) shows the flow

211

field distribution calculated with PIV software. Applied voltage, 30 kV; discharge

212

current density, 12.7 µA/cm2.

213

Ozone generation and decomposition

214

Figure 7 shows ozone generation and decomposition in the three-stage

215

plasma-assisted catalysis system vs. the SIE of DBD. The SIE of BCD is fixed at

216

128.9 J/L. The results indicate that the total ozone concentration is linearly dependent

217

on the SIE. Meanwhile, BCD produces additional ozone, but at a much lower rate

218

than DBD. For example, BCD adds only extra 208 ppm ozone when the SIE is 128.9

219

J/L. However, BCD makes a significant contribution to ozone decomposition. For

220

example, when the SIE of DBD is 35 J/L, the ozone decomposition efficiency 13

ACS Paragon Plus Environment

Environmental Science & Technology

221

increases from 97.5% to 99.1% after BCD is turned on. This is because BCD collects

222

the aerosols produced in the previous stage, and, since the aerosols cause deactivation

223

of the catalyst, high catalyst activity is maintained downstream.

224 225

Figure 7. Ozone generation and decomposition of DBD vs. the SIE, where the SIE of

226

BCD is fixed at 128.9 J/L.

227

Toluene removal

228

Figure 8 shows the toluene removal efficiency of the three-stage plasma-assisted

229

catalysis system under four conditions: DBD alone, DBD-BCD, DBD-catalyst, and

230

DBD-BCD-catalyst. The toluene removal efficiency with the DBD-BCD-catalyst

231

system is significantly higher than that achieved with DBD alone or DBD-catalyst,

232

especially when the SIE is low. For example, when the SIE is at 35 J/L, the toluene

233

removal efficiencies in the DBD, DBD-BCD, DBD-catalyst, and DBD-BCD-catalyst

234

are around 37%, 72%, 68%, and 95%, respectively. Furthermore, the energy

235

consumption is almost one order smaller than that reported elsewhere10.

14

ACS Paragon Plus Environment

Page 14 of 25

Page 15 of 25

Environmental Science & Technology

236 237

Figure 8. Toluene removal efficiency vs. the SIE of DBD under four conditions: DBD

238

alone, DBD-BCD, DBD-catalyst, and DBD-BCD-catalyst. The horizontal ordinate

239

refers the SIE of DBD and the SIE of BCD is 128.9 J/L.

240

With regards to plasma induced ozone generation and toluene decomposition, there

241

are three fundamental reactions: R1, R2 and R341,42. According to the results of ozone

242

generation and toluene removal induced by the DBD reactor, they are linearly

243

dependent on each other (Details in S5 of Supporting Information). So, it can be

244

concluded that the two parallel gaseous reactions R2 and R3 almost independently

245

consume O radicals.

246

O radical production:

e + O2 → e + O + O

(R1)

247

O3 generation:

O + O2 + M → O3 + M

(R2)

248

Toluene decomposition: O + C6 H 5 ⋅ CH 3 → product

249

where, M refers to O2 and N2 in air. By using the equations (S1) and (S2) in

250

Supporting Information, the energy yields (in the form of G-values) for ozone

251

generation G(O3) and toluene decomposition G(-toluene) can be calculated about 4.08 15

ACS Paragon Plus Environment

(R3)

Environmental Science & Technology

252

(molecules/100 eV) and 0.40 (molecules/100 eV), respectively.

253

In the DBD-BCD-catalyst system, as shown in emission spectra, BCD produces lots

254

of active species, such as OH, O and N2*. They can be used for toluene and aerosol

255

decomposition. In this stage, aerosol produced in previous DBD stage can be charged

256

and collected on the surface of honeycomb catalyst, then can be decomposed in situ

257

by plasma and catalyst because of the back corona generated in the channel of

258

honeycomb26. So, the catalyst downstream can be protected from aerosol

259

contamination and the three-stage system performs best in toluene removal as shown

260

in Figure 8. The ozone produced in both DBD and BCD is actively used in the

261

catalyst stage. Catalytic ozone oxidation is the most important process for toluene, CO,

262

and other by-products removal. The mechanism of plasma catalysis degradation has

263

already been well studied in our previous works30,41 and others’ works9,12,13,17-19.

264

Gas phase products

265

Figure 9 presents the FTIR spectra of the gaseous product of toluene

266

decomposition using both DBD alone and the DBD-BCD-catalyst system. The results

267

show that by-products such as formaldehyde, formic acid, NOx, ozone, and carbon

268

monoxide are produced during the degradation of toluene by the DBD. However, most

269

of the incompletely decomposed VOCs, carbon monoxide, and ozone are removed

270

when the BCD is turned on and the downstream Ag-Mn-O catalyst works. In the

271

DBD-BCD-catalyst system, the main product of toluene decomposition is CO2 and

272

H2O. 16

ACS Paragon Plus Environment

Page 16 of 25

Page 17 of 25

Environmental Science & Technology

273 274

Figure 9. FTIR spectra of the gas phase product of toluene decomposition with (a)

275

DBD alone and (b) DBD-BCD-catalyst.

276

For plasma-assisted catalysis system, the by-product of NOx can reach several

277

hundred ppm at high SIE of plasma9,11, so it should receive more attention. However,

278

the average SIE of single discharge unit of DBD in this work is quite small, even less

279

than 3 J/L when the total SIE of DBD reaches 35 J/L (12 quartz tubes discharge units).

280

As a result, the NOx produced by DBD is negligible that the concentration of NO2 is

281

0.1 ppm and 0.2 ppm when the SIE of DBD reaches 35 J/L and 64 J/L, respectively.

282

With regards to BCD, the NOx production can also be neglected because the

283

concentration of NO2 is only 1.1 ppm when the SIE of BCD is 128.9 J/L.

284

CO selectivity, CO2 selectivity and carbon balance

285

Figure 10 shows the CO selectivity, CO2 selectivity and carbon balance of the

286

three-stage system in four conditions. The results show that CO2 selectivity and

287

carbon balance are improved when the BCD and catalyst are used. For DBD alone,

288

DBD-BCD, DBD-catalyst, and DBD-BCD-catalyst, the CO2 selectivity is 67 %, 73 %,

289

86 % and 87 %, respectively, and the carbon balance is 41 %, 48 %, 71 % and 82 %,

290

respectively. The higher CO2 selectivity and carbon balance in DBD-BCD-catalyst 17

ACS Paragon Plus Environment

Environmental Science & Technology

process can be attributed to the aerosol decomposed by BCD and the catalytic ozone

292

oxidation of incompletely decomposed VOCs by the catalyst downstream. CO, CO2 selectivity and carbon balance (%)

291

100

CO selectivity CO2 selectivity

Carbon balance

80

60

40

20

0

293

DBD

DBD-BCD

DBD-catalyst DBD-BCD-catalyst

Plasma-assisted catalysis system

294

Figure 10. CO selectivity, CO2 selectivity and carbon balance of the three-stage

295

system in four different conditions: DBD alone, DBD-BCD, DBD-catalyst and

296

DBD-BCD-catalyst. The SIE of DBD and BCD is fixed at 64 J/L and 128.9J/L,

297

respectively.

298

Catalyst degradation

299

For VOCs decomposition with plasma-assisted catalysis, especially two-stage

300

plasma catalysis reactor, the aerosol produced by plasma stage will induce catalyst

301

degradation. The XPS spectrum analysis of the aerosols deposited on catalyst surface

302

show that most carbon in aerosols are in the forms of C-C and/or C-H (59.6 %) and

303

COOH and/or COOR (28.2 %). Details can be found in S6 of Supporting Information.

304

For the three-stage system, BCD placed between DBD and catalyst plays an important

305

role in aerosol collection and decomposition. As shown in Figure 11, the toluene

306

removal efficiency without BCD decreases to below 70 % when operation time 18

ACS Paragon Plus Environment

Page 18 of 25

Page 19 of 25

Environmental Science & Technology

307

increases to 10 hours, but the removal efficiency with BCD remains stable at high

308

level around 98 %. So, the three-stage system is proven to be feasible for industrial

309

application not only for less by-products emission, but also for stable removal

310

efficiency and prolonged lifetime of catalyst.

311 312

Figure 11. The comparison of toluene removal efficiency in DBD-catalyst and

313

DBD-BCD-catalyst with operation time. The SIE values of DBD and BCD are fixed

314

at 64 J/L and 128.9J/L, respectively.

315

Author information:

316

Corresponding author

317

Tel: +86-571-88273897, Fax: +86-571-88210786, E-mail: [email protected]

318

Notes: The authors declare no completing financial interest

319

Acknowledgments

320

This work is supported financially by the Natural Science Foundation of China (No.

321

21276232,41476080&51377145),

322

Development

323

2013AA065001),

Program

of

Natural

National China

Science

High

(863

Technology

Program)

Foundation

of

19

ACS Paragon Plus Environment

Research

and

(No.2013AA065005, Zhejiang

Province

Environmental Science & Technology

324

(No.LY13E070002& LQ14D060004) and Natural Science Foundation of Guangdong

325

Province (No. 2014A030310196).

326

Supporting Information Available:

327

The experimental setup of the particle collection measurement system for the BCD

328

reactor (S1 text and Figure S1); the experimental setup of the 2D-PIV system for flow

329

field measurement in BCD reactor (S2 text and Figure S2); the details of the electric

330

measurement and gas composition measurement instruments (S3 text); the definitions

331

of toluene removal efficiency, CO and CO2 selectivity, carbon balance, SIE and BCD

332

discharge current density (S4); the analysis of ozone production and toluene

333

decomposition in DBD reactor (S5, Figure S5, Figure S6 and Figure S7); the XPS

334

spectrum analysis of the aerosols deposited on catalyst surface (S6, Figure S8 and

335

Table S1). This information is available free of charge via the Internet at

336

http://pubs.acs.org/.

337

References

338

(1). H. H. Kim, Nonthermal plasma processing for air-pollution control: a historical

339

review, current issues, and future prospects, Plasma Process Polym. 2004, 1 (2):

340

91-110.

341

(2). J. Van Durme, J. Dewulf, C. Leys and H. Van Langenhove, Combining

342

non-thermal plasma with heterogeneous catalysis in waste gas treatment: a review,

343

Appl. Catal. B-Environ. 2008,78 (3-4): 324-333.

344

(3). J. C. Whitehead, Plasma catalysis: a solution for environmental problems, Pure 20

ACS Paragon Plus Environment

Page 20 of 25

Page 21 of 25

Environmental Science & Technology

345

Appl. Chem. 2010,82 (6) : 1329-1336.

346

(4). S. Samukawa, M. Hori, S. Rauf, K. Tachibana, P. Bruggeman, G. Kroesen, J. C.

347

Whitehead, A. B. Murphy, A. F. Gutsol, S. Starikovskaia, U. Kortshagen, J. P.

348

Boeuf, T. J. Sommerer, M. J. Kushner, U. Czarnetzki and N. Mason, The 2012

349

plasma roadmap, J. Phys. D Appl. Phys. 2012,45: 25300125.

350 351 352 353

(5). C. J. Liu, G. P. Vissokov and B. Jang, Catalyst preparation using plasma technologies, Catal. Today 2002,72 (3-4) :173-184. (6). D. G. Cheng, Plasma decomposition and reduction in supported metal catalyst preparation, Catalysis Surveys from Asia 2008,12 (2) : 145-151.

354

(7). H. Winands, K. P. Yan, S. A. Nair, G. Pemen and B. van Heesch, Evaluation of

355

corona plasma techniques for industrial applications: hpps and dc/ac systems,

356

Plasma Process Polym. 2005,2 (3): 232-237.

357

(8). N. Benard, A. Mizuno and E. Moreau, A large-scale multiple dielectric barrier

358

discharge actuator based on an innovative three-electrode design, J. Phys. D Appl.

359

Phys. 2009,42 : 23520423.

360 361 362

(9). H. H. Kim and A. Ogata, Nonthermal plasma activates catalyst: from current understanding and future prospects, Eur. Phys. J.-Appl. Phys. 2011,55: 138061. (10).

N. Jiang, N. Lu, K. Shang, J. Li and Y. Wu, Effects of electrode geometry on

363

the performance of dielectric barrier/packed-bed discharge plasmas in benzene

364

degradation, J. Hazard. Mater. 2013,262 : 387-393.

365

(11).

N. Jiang, N. Lu, K. Shang, J. Li and Y. Wu, Innovative approach for benzene 21

ACS Paragon Plus Environment

Environmental Science & Technology

366

degradation using hybrid surface/packed-bed discharge plasmas, Environ. Sci.

367

Technol. 2013,47 (17) : 9898-9903.

368

(12).

H. B. Huang, D. Q. Ye, D. Leung, F. D. Feng and X. J. Guan, Byproducts and

369

pathways of toluene destruction via plasma-catalysis, J. Mol. Catal. A-Chem.

370

2011,336 (1-2): 87-93.

371

(13).

H. H. Kim, A. Ogata, M. Schiorlin, E. Marotta and C. Paradisi, Oxygen

372

isotope ((18)o(2)) evidence on the role of oxygen in the plasma-driven catalysis

373

of voc oxidation, Catal. Lett. 2011,141 (2): 277-282.

374

(14).

H. H. Kim, J. H. Kim and A. Ogata, Microscopic observation of discharge

375

plasma on the surface of zeolites supported metal nanoparticles, J. Phys. D Appl.

376

Phys. 2009,42 (13): 135210.

377

(15).

Y. F. Guo, D. Q. Ye, K. F. Chen, J. C. He and W. L. Chen, Toluene

378

decomposition using a wire-plate dielectric barrier discharge reactor with

379

manganese oxide catalyst in situ, J. Mol. Catal. A-Chem. 2006, 245 (1-2):93-100.

380

(16).

X. Tu and J. C. Whitehead, Plasma-catalytic dry reforming of methane in an

381

atmospheric dielectric barrier discharge: understanding the synergistic effect at

382

low temperature, Appl. Catal. B-Environ. 2012,125 :439-448.

383

(17).

H. B. Huang, D. Q. Ye and D. Leung, Abatement of toluene in the

384

plasma-driven catalysis: mechanism and reaction kinetics, IEEE T. Plasma Sci.

385

2011,39 (3): 877-882.

386

(18).

H. L. Chen, H. M. Lee, S. H. Chen, M. B. Chang, S. J. Yu and S. N. Li, 22

ACS Paragon Plus Environment

Page 22 of 25

Page 23 of 25

Environmental Science & Technology

387

Removal of volatile organic compounds by single-stage and two-stage plasma

388

catalysis systems: a review of the performance enhancement mechanisms, current

389

status, and suitable applications, Environ. Sci. Technol. 2009,43 (7): 2216-2227.

390

(19).

M. Vandenbroucke, R. Morent, N. De Geyter and C. Leys, Non-thermal

391

plasmas for non-catalytic and catalytic VOC abatement, J. Hazard. Mater.

392

2011,195: 30-54.

393 394 395 396 397

(20).

S. Sato, K. Hensel, H. Hayashi, K. Takashima and A. Mizuno, Honeycomb

discharge for diesel exhaust cleaning, J. Electrostat. 2009,67 (2-3):77-83. (21).

K. Hensel, S. Sato and A. Mizuno, Sliding discharge inside glass capillaries,

IEEE T. Plasma Sci. 2008,36 (4Part 1) :1282-1283. (22).

A. Jaworek, A. T. Sobczyk and E. Rajch, Investigations of dc corona and

398

back discharge characteristics in various gases, Journal of Physics: Conference

399

Series 142(1): 012010.

400 401 402 403 404 405 406 407

(23).

A. Krupa, Laboratory investigations of back discharge in multipoint-plane

geometry in flue gases, J. Electrostat. 2009,67 (2-3) :291-296. (24).

A. Krupa, Back discharge in multipoint-plane geometry in flue gases, Eur.

Phys. J. D 2009,54 (2) :265-270. (25).

T. Czapka, Back-corona discharge phenomenon in the nonthermal plasma

system, IEEE T. Plasma Sci. 2011,39 (11SIPart 1) :2242-2243. (26).

F. D. Feng, L. L. Ye, J. Liu and K. P. Yan, Non-thermal plasma generation by

using back corona discharge on catalyst, J. Electrostat. 2013,71 (3) :179-184. 23

ACS Paragon Plus Environment

Environmental Science & Technology

408 409 410 411 412 413 414

(27).

K. Hensel, Z. Machala and P. Tardiveau, Capillary microplasmas for ozone

generation, Eur. Phys. J.-Appl. Phys. 2009,47: 228132. (28).

K. Hensel, Microdischarges in ceramic foams and honeycombs, Eur. Phys. J.

D 2009,54 (2):141-148. (29).

U. Kogelschatz, Dielectric-barrier discharges: their history, discharge physics,

and industrial applications, Plasma Chem. Plasma P. 2003, 23 (1):1-46. (30).

X. J. Tang, F. D. Feng, L. L. Ye, X. M. Zhang, Y. F. Huang, Z. Liu and K. P.

415

Yan, Removal of dilute vocs in air by post-plasma catalysis over ag-based

416

composite oxide catalysts, Catal. Today 2013,211:39-43.

417

(31).

T. Czech, A. T. Sobczyk and A. Jaworek, Optical emission spectroscopy of

418

point-plane corona and back-corona discharges in air, Eur. Phys. J. D 2011,65 (3) :

419

459-474.

420 421 422

(32).

R.W.B. Pearse and A.G. Gaydon, The identification of molecular spectra,

Chapman and Hall, London, 1976. (33).

M. Villa, M. Calixto-Rodriguez, H. Martinez, J. C. Poveda, P. G. Reyes and P.

423

Altuzar, Asphaltene surface erosion in air plasma, Plasma Science and

424

Technology. 2010,12 (1) :81-86.

425

(34).

S. Stojadinovic, J. Radic-Peric, R. Vasilic, and M. Peric, Spectroscopic

426

investigation of direct current (DC) plasma electrolytic oxidation of zirconium in

427

citric acid, Applied Spectroscopy, 2014,68 (1):101-112.

428

(35).

K.V. Kozlov, H.E. Wagner, R. Brandenburg and P. Michel, Spatio-temporally 24

ACS Paragon Plus Environment

Page 24 of 25

Page 25 of 25

Environmental Science & Technology

429

resolved spectroscopic diagnostics of the barrier discharge in air at atmospheric

430

pressure , J. Phys. D: Appl. Phys. 2001,34(21): 3164–3176.

431 432 433 434 435

(36).

A. Mizuno, Electrostatic precipitation, IEEE T. Dielect. El. In. 2000,7(5):

615-624. (37).

A. Krupa, M. Lackowski and T. Czech, Dust particles motion in back

discharge, Journal of Physics: Conference Series 2008,142(1): 012040. (38).

X. Zhang, F. Feng, S. Li, X. Tang, Y. Huang, Z. Liu, and K. Yan. Aerosol

436

formation from styrene removal with an AC/DC streamer corona plasma system

437

in air. Chemical Engineering Journal. 2013, 232: 527-533.

438

(39).

J. Mizeraczyk, M. Kocik, J. Dekowski, M. Dors, J. Podlinski, T. Ohkubo, S.

439

Kanazawa and T. Kawasaki, Measurements of the velocity field of the flue gas

440

flow in an electrostatic precipitator model using piv method, J. Electrostat.

441

2001,51:272-277.

442 443 444

(40).

J. Westerweel, Fundamentals of digital particle image velocimetry, Meas. Sci.

Technol. 1997,8 (12) :1379-1392. (41).

L. L. Ye, F.D. Feng, J. Liu, X. J. Tang, Y. F. Huang, Z. Liu and K. P. Yan,

445

Toluene decomposition by a two-stage hybrid plasma catalyst system in dry air,

446

IEEE T. Plasma Sci. 2014,42 (11):3529-3538.

447 448

(42).

K. Yan. Corona plasma generation. Eindhoven University of Technology,

Eindhoven, 2001.

25

ACS Paragon Plus Environment