Characterization of Particulate Matter Emissions from a Current

Jun 24, 2014 - Citation data is made available by participants in Crossref's Cited-by Linking service. For a more comprehensive list of citations to t...
1 downloads 0 Views 633KB Size
Subscriber access provided by RUTGERS UNIVERSITY

Article

Characterization of Particulate Matter Emissions from a Current Technology Natural Gas Engine Arvind Thiruvengadam, Marc Besch, Seungju Yoon, John Francis Collins, Hemanth Kappanna, Daniel Carder, Alberto Ayala, Jorn Herner, and Mridul Gautam Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/es5005973 • Publication Date (Web): 24 Jun 2014 Downloaded from http://pubs.acs.org on June 30, 2014

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 28

Environmental Science & Technology

Lubrication oil

Stoichiometric CNG with  Three‐way Catalyst   

ACS Paragon Plus Environment

Environmental Science & Technology

Page 2 of 28

1

Characterization of Particulate Matter Emissions

2

from a Current Technology Natural Gas Engine

3

Arvind Thiruvengadam*1, Marc C. Besch1, Yoon Seungju2, John Collins2, Hemanth Kappanna1,

4

Daniel K Carder1, Alberto Ayala2, Jorn Herner2, Mridul Gautam1

5

1

Mechanical and Aerospace Department, West Virginia University, Morgantown, West Virginia

6 7

26505, Phone (304) 293 0805, Fax (304) 293 6689 2

California Air Resources Board, 1001 I Street, Sacramento, CA 95812, Phone (916) 327 8097,

8 9

Fax (916) 322 4357 Corresponding Author Email: [email protected]

10

RECEIVED DATE (to be automatically inserted after your manuscript is accepted if

11

required according to the journal that you are submitting your paper to)

12

ABSTRACT

13

Experiments were conducted to characterize the particulate matter (PM) size distribution, number

14

concentration, and chemical composition emitted from transit buses powered by a USEPA 2010

15

compliant, stoichiometric heavy-duty natural gas engine equipped with a three-way catalyst

16

(TWC). Results of the particle size distribution showed a predominant nucleation mode centered

17

close to 10 nm. PM mass in the size range of 6.04 to 25.5 nm correlated strongly with mass of

ACS Paragon Plus Environment

1

Page 3 of 28

Environmental Science & Technology

18

lubrication oil derived elemental species detected in the gravimetric PM sample. Results from oil

19

analysis indicated an elemental composition that was similar to that detected in the PM samples.

20

The source of elemental species in the oil sample can be attributed to additives and engine wear.

21

Chemical speciation of particulate matter (PM) showed that lubrication oil based additives and

22

wear metals were a major fraction of the PM mass emitted from the buses. The results of the study

23

indicate the possible existence of nanoparticles below 25 nm formed as a result of lubrication oil

24

passage through the combustion chamber. Furthermore, the results of oxidative stress (OS)

25

analysis on the PM samples indicated strong correlations with both the PM mass calculated in the

26

nanoparticle size bin and the mass of elemental species that can be linked to lubrication oil as the

27

source.

28

INTRODUCTION

29

Engine manufacturers have adopted advanced combustion strategies and after-treatment

30

technologies to meet current USEPA 2010 emissions regulations. The diesel segment of the heavy-

31

duty population incorporates exhaust gas recirculation (EGR), variable geometry turbochargers

32

(VGT), diesel particulate filters (DPF), and selective catalytic reduction (SCR) systems for

33

emissions reduction. The natural gas fueled engines incorporate stoichiometric fueling, cooled

34

EGR, and a TWC. The soot free combustion of natural gas enables Original Equipment

35

Manufacturers (OEM) to meet particulate matter (PM) standards without the use of a particulate

36

filter. Exhaust from both natural gas vehicles and DPF-equipped diesel vehicles are characterized

37

by low concentrations of accumulation mode particles.1 Diesel engines have exhibited significant

38

concentrations of nucleation mode particles linked to catalytic oxidation of fuel and lube oil

39

derived sulfur at elevated exhaust gas temperature operating conditions.1,2 The discussions of

ACS Paragon Plus Environment

2

Environmental Science & Technology

Page 4 of 28

40

sulfuric acid based particles found in the literature bring to light the importance of lubrication oil

41

consumption as a possible precursor to nanoparticle formation.1,2 Many authors attribute the sulfur

42

in temperature dependent nucleation mode particle emissions to be primarily from lubrication oil

43

rather than from ultralow sulfur diesel fuel.3,4,5

44

Components of lubrication oil can manifest themselves as both organic and inorganic emissions

45

in the exhaust of an internal combustion engine. The process of lubrication oil based metallic

46

compounds to undergo volatilization during combustion and condensation during exhaust gas

47

cooling was documented by Khalek et al. The study also showed that engines with lower soot

48

emissions such as spark-ignited engines favored the re-nucleation of lubrication oil additives in

49

the exhaust.6 The contribution of lubrication oil to PM emissions from uncontrolled diesel engines

50

has not been a significant factor because the soot produced from in-cylinder combustion of diesel

51

fuel in legacy engines overwhelms the PM emissions attributable to lubrication oil by several

52

orders of magnitude.7 Results of Liu et al. show that metallic emissions account for only a small

53

fraction of PM in an uncontrolled diesel engine, while the use of DPF reduces this fraction by over

54

90%. The study also showed a higher metal content with the use of SCR compared to a DPF only

55

configuration.8 The contribution of lubrication oil to tailpipe PM emissions from DPF-equipped

56

engines is also not likely to be significant. In modern diesel engines, the oxidation catalyst controls

57

the organic fraction of lubrication oil PM, and the DPF controls the inorganic fraction (soot and

58

metals) of lubrication oil PM. A study by McGeehan et al has shown that all of the ash deposited

59

in the DPF of diesel engine is predominantly inorganic and dominated by lubrication oil additives.9

60

In the case for natural gas engines, the contribution of lubrication oil to tailpipe PM could be

61

significant because, while the TWC will oxidize the organic fraction of PM, there is no DPF to

62

remove the inorganic fraction of PM consisting of soot and trace metals.

ACS Paragon Plus Environment

3

Page 5 of 28

Environmental Science & Technology

63

Current natural gas engines operate on a spark-ignited (SI) engine platform similar to gasoline

64

fueled engines. Zielinska et al. show that the composition of polycyclic aromatic hydrocarbon

65

(PAH) emissions in gasoline engine exhaust more closely resembles the composition of PAH in

66

used lubrication oil rather than in fuel.10 Recent measurement in the Caldecot tunnel indicate that

67

the lubrication oil could be the dominant contributor to primary organic aerosol (POA) emitted by

68

heavy and light-duty vehicles.11 The study presents evidence of POA compositions being

69

influenced more by lubrication oil based organic compounds rather than byproducts of incomplete

70

combustion of gasoline or diesel fuel.11 Lubrication oil also consists of a range of additives that

71

provide detergents, dispersant, acid neutralizers, anti-oxidants, corrosion inhibitors, and anti-wear

72

properties to the lubricant. Consequently, lubrication oil combustion results in inorganic

73

constituents such as calcium, zinc, phosphorus, and sulfur in the exhaust.12

74

Factors that could affect the health impacts of heavy duty PM emissions include particle

75

composition, particle number concentration, size distribution, surface area distribution, physical

76

characteristics, and the penetration fraction into the human lungs. Very few studies have attempted

77

to relate PM oxidative stress (OS) characterization with composition characteristics of PM

78

emissions from heavy-duty engines. Verma et al. observed a relationship between transition metals

79

present in PM samples and oxidative stress in alveolar macrophage cells using a reactive oxidative

80

species (ROS) assay.13 Biswas et al. observed strong statistical correlations between oxidative

81

potential measured using a dithiothreitol (DTT) assay and the organic acid and water soluble

82

organic carbon concentrations of PM extracts.14 These and most other studies on the OS potential

83

of heavy duty PM emissions have reported data from legacy or retro-fitted diesel engines. There

84

is little literature on the OS potential of PM emissions from modern natural gas engines. The

85

increasing population of natural gas engines in urban applications such as transit buses, refuse

ACS Paragon Plus Environment

4

Environmental Science & Technology

Page 6 of 28

86

trucks, and goods movement has raised concern about the potential PM related health implications

87

of natural gas engine emissions. Current knowledge of PM size distribution, number concentration,

88

and chemical characteristics is limited to older technology lean-burn natural gas engines. Lean-

89

burn natural gas engines are SI internal combustion engines that operate with excess air. Since

90

newer natural gas engines are subject to stricter NOx regulations, engine manufacturers have

91

adopted a stoichiometric fueling (chemically correct air to fuel ratio to achieve complete

92

combustion of fuel) strategy to leverage the use of TWC for NOx reductions. Lean-burn natural

93

gas engines typically operate with a simple oxidation catalyst for CO and hydrocarbon reduction

94

as opposed to TWC that simultaneously reduce NOx, CO and hydrocarbons. Stoichiometric

95

natural gas engines operate at higher exhaust gas temperatures when compared to lean-burn

96

engines due to the higher fueling rate relative to mass of air. The findings presented in this work

97

describe the chemical composition, size distribution, and number concentration of PM emissions

98

from two modern stoichiometric natural gas vehicles. The results also show the correlation of

99

oxidative potential with engine wear and lubrication oil derived elements.

100

EXPERIMENTAL PROCEDURE

101

Two heavy-duty natural gas transit buses were tested on West Virginia University’s (WVU)

102

transportable heavy-duty chassis dynamometer. The buses were powered by USEPA 2010

103

compliant natural gas fueled engines. Table 1 lists the engine and vehicle specifications of the two

104

test vehicles. Both buses were identical in their engine and vehicle specification, and in to their

105

third year of service in the fleet. One bus had accumulated 84,000 miles, while the other had

106

accumulated 77,000 miles prior to this study. Both buses were in the middle of their maintenance

107

interval during the testing period. The typical retirement age for a transit bus is 12 years or 500,000

108

miles, whichever criteria is satisfied first.

ACS Paragon Plus Environment

5

Page 7 of 28

Environmental Science & Technology

109 110

Table 1. Engine and Vehicle Specifications of the Test Vehicles Engine Manufacturer

Cummins

Engine Model

ISLG 280

Engine Model Year

2007

Displacement (L)

8.9

Power (hp)@ speed (rpm) 280 @ 2000 Fuel

CNG

After-treatment

Three-way catalyst

After-treatment manufacturer

Cummins Solution

Vehicle Manufacturer

Daimler America

Emissions Certification

PM: 0.01 gms/bhp-hr; NOx: 0.20 gms/bhp-hr

Emissions Bus

North

111 112

Both vehicles were exercised over three driving cycles: the urban dynamometer driving schedule

113

(UDDS), 45 mph steady-state cruise, and idle operating mode cycles. Extended versions of the

114

UDDS (triple length cycle), one hour cruise mode, and one hour idle operation were performed to

115

collect adequate PM samples on to the gravimetric filters for chemical speciation analysis and for

116

better resolution over the gravimetric weighing system. Prior to beginning of sample collection

117

vehicles were pre-conditioned by operating over respective driving cycles prior to the tests that

118

involved sample collection. This ensured vehicle engine and after-treatment systems were in

119

optimal thermodynamic state for representative gaseous and PM emissions rate. Table S1 in the

ACS Paragon Plus Environment

6

Environmental Science & Technology

Page 8 of 28

120

supplemental information lists the different sampling media and flow rates for the respective

121

sampling streams. Samples were collected on respective media recommended by the different

122

analysis procedures, over three consecutive hot starts with 20 min soak times in between tests. One

123

hour duration tunnel blanks were collected for all media before the start of each test day. The test

124

matrix also involved the complete chemical speciation of the gas phase and particulate phase

125

constituents of exhaust that included analysis for PAH, VOC, carbonyls, metals, ions, elemental

126

carbon (EC), and organic carbon (OC).

127

Regulated gaseous pollutants were quantified using the WVU transportable emissions

128

measurement system (TEMS), and the test results are publicly available.21 Figure S1 in the

129

supplemental information represents the schematic of the code of federal regulations (CFR) Title

130

40 Part 1065 compliant emissions measurement system contained within the TEMS, as well as the

131

unregulated sampling streams employed in this study.

132

Particle size distributions and number concentrations were continuously measured at 1 Hz. using

133

an Engine Exhaust Particle Sizer (TSI-EEPS Model 3090). The TSI EEPS is designed to measure

134

particles in the size range of 5.6 to 560 nm. The Electrical Aerosol Detector (TSI EAD Model

135

3070A) was also used to measure a unique parameter called aerosol length (mm/cm3) which is

136

indicative of lung deposited particle surface area.15 Particle size measurements were performed by

137

directly sampling from the primary dilution tunnel of the constant volume sampling (CVS) system.

138

Instantaneous primary CVS dilution ratios were calculated using the CVS tunnel flow and engine

139

exhaust flow. The primary CVS dilution air is at ambient condition, filtered using high efficiency

140

particulate air (HEPA) filter. Temperature and humidity of the primary dilution air was

141

continuously recorded.

ACS Paragon Plus Environment

7

Page 9 of 28

Environmental Science & Technology

142

The study also included the characterization of the OS potential of PM through dithiothreitol

143

(DTT) and alveolar macrophage reactive oxygen species (ROS) assays. The DTT assay is a cell

144

free, chemical based assay that is highly selective in response to organic materials and certain

145

transition metals such as copper and manganese.16,17 The rate of consumption of the chemical DTT

146

is found to be directly proportional to the OS potential of the sample.18 A study by Charrier and

147

Anastasio has illustrated the response of the DTT assay towards the presence of transition metals,

148

specifically copper and manganese. The study further shows that up to 80% of DTT consumption can

149

be attributed to the presence of transition metals in a sample consisting of mixture of transition metals

150

and quinones.17

151

Alveolar macrophage assay is a cell based OS assay that exposes alveolar macrophage tissues

152

extracted from a rat to the PM samples. Alveolar macrophages are commonly found in the inner

153

epithelial cells of the airways and lungs and hence by quantifying ROS generation within alveolar

154

tissues, would be an indicator of pulmonary inflammatory responses to PM.13 A recent study by

155

Landerman et al. has shown that this assay is effective for PM mass loading of less than 100

156

micrograms and that it accurately represents pulmonary response to PM exposure, as the lung airways

157

are the first line of defense for the human body against particulate matter ingestion19. Recent studies

158

by Hu et al. and Verma et al. have also observed the selectivity of this assay towards water soluble

159

transition metals.16,20

160

High volume sampling and extended test cycles were employed to collect adequate PM mass

161

onto T60A40 filter substrates for the respective OS assays. Detailed procedures of PM sample

162

extraction and analysis procedures for DTT and alveolar macrophage assay are described in the

163

works of Cho et al.18 and Verma et al.20 respectively. This paper will use the results from the OS

164

assays to present statistical correlations with chemical composition of the PM. Detailed analysis

165

of OS potential of PM will be the subject of a different paper.

ACS Paragon Plus Environment

8

Environmental Science & Technology

Page 10 of 28

166 167

RESULTS AND DISCUSSION

168

Figure 1 shows the dilution corrected average particle size distributions and concentrations

169

observed during the triple-length UDDS cycle from the two CNG buses. The error bars in the

170

figure show the maximum and minimum particle concentration change for each particle diameter

171

over three hot start repeats. The particle size distribution from both buses show particle

172

concentrations close to 1E7 for particle diameters close to 10 nm size range. The error bars indicate

173

a lower variation in particle concentration in the 10 nm size range for both buses over three hot

174

start triple length UDDS tests. Particle size distributions from both buses indicate the emission of

175

particles in the accumulation mode (50-100 nm). However, observed particle concentrations in the

176

accumulation mode were an order of magnitude lower than particles in the nucleation mode (100nm is not

183

commonly observed in exhaust of natural gas or DPF-equipped diesel engines.

ACS Paragon Plus Environment

9

Page 11 of 28

Environmental Science & Technology

184 185

Figure 1. Cycle averaged particle size distribution and concentration during UDDS cycle

186

Figure 2 shows the average particle size distribution and concentration, corrected for

187

instantaneous dilution ratios during the 45 MPH cruise mode operation. The results from both

188

buses showed high variability in the measured particle size distribution and concentration. Particle

189

concentrations from both buses during the cruise mode operation were found to be two orders of

190

magnitude lower compared to the transient UDDS operation. The particle concentrations measured

191

over the steady-state cycle were characterized by higher levels of electrometer noise due to the

192

low signal to noise ratio attributed by the low PM emissions during cruise mode operation. Very

193

low gravimetric PM mass measured over the steady-state cycles from both buses further

194

corroborate the low particle concentrations measured using the TSI EEPS. Cruise mode operation

195

contributes to a relatively steady thermodynamic state of the engine. This steady-state

196

characteristic results in better sealing of piston rings and oil pathways and therefore inhibiting the

197

contribution of lubrication oil to tailpipe PM emissions.

ACS Paragon Plus Environment

10

Environmental Science & Technology

Page 12 of 28

198 199

Figure 2. Cycle averaged particle size distribution and concentration during 45 MPH cruise

200

Figure 3 shows average particle size distribution and concentration corrected for instantaneous

201

dilution ratios during the idle phase. Particle concentrations from bus 1 were found to be close to

202

levels in tunnel blanks. However, bus 2 exhibited significantly higher particle concentration over

203

a broad size range of the distribution. The highest particle concentrations were detected at both

204

nucleation mode and accumulation mode regions of the size distribution for bus 2 during idle

205

operation. The nucleation mode particle size distribution was centered on the 10-20 nm size range

206

and that in the accumulation mode was centered around 80-100 nm size range. In corroboration

207

with particle size distribution results from bus 2, the gravimetric filter samples collected during

208

idle mode operation reported higher mass loading compared to bus 1 and discoloration of filter

209

materials. The observed particle size distribution could be attributed to in-cylinder combustion of

210

lubrication oil. The entry of lubrication oil in to the combustion chamber is dependent on engine

211

load. Typically low-load operations result in insufficient sealing of the piston rings which can

212

contribute to the combustion of lubrication oil. The observed particle size distribution from bus 2

ACS Paragon Plus Environment

11

Page 13 of 28

Environmental Science & Technology

213

could be attributed to worn cylinder linings and hence lower piston ring sealing during the

214

extended idle operation. The difference in PM size distribution between the two buses could be

215

indicative of the differences in their day-to-day operating characteristics that influences their

216

engine wear pattern and consequently the oil consumption characteristics.

217 218

Figure 3. Cycle averaged particle size distribution and concentration during idle operation

219

In comparing the results obtained from this study to previous work documented by Holmen and

220

Ayala1, the particle size distribution and concentration observed in cruise mode operation is similar

221

to the CVS measurements obtained from older technology lean-burn natural gas engines with an

222

oxidation catalyst.1 Similar particle concentrations in the range of 1E4 to 1E5 for particle diameters

223

less than 10 nm is observed between both studies. Similarity in idle mode PM emissions between

224

the two studies is observed only for bus 1. Bus 2 PM emissions are significantly different from

225

both bus 1 and results from Holmen and Ayala.1 The similarity in PM emissions between older

226

and newer technology natural gas engines suggests that PM emissions could largely be contributed

ACS Paragon Plus Environment

12

Environmental Science & Technology

Page 14 of 28

227

only by lubrication oil and not so influenced by changes in combustion of fuel and type of after-

228

treatment system.

229

Figure 4 shows the mass fraction of different particulate phase chemical species emitted from

230

the two CNG buses. The distance-specific emissions rates of the individual species are detailed

231

elsewhere.21

232

The mass fraction results of PM from stoichiometric operating CNG engines reveal a very

233

interesting composition. The fraction of organic carbon (OC) emissions in comparison to other

234

species is significantly lower than previously documented for lean-burn natural gas engines.21,22

235

The lower OC composition can be attributed to the high post-TWC exhaust gas temperatures that

236

were observed to be greater than 500oC for the transient and steady-state operation and close to

237

300oC for idle operation. Such high temperatures are conducive for efficient catalytic oxidation of

238

higher and lower chain hydrocarbons with the exception of methane.23 VOC analysis indicated all

239

higher chain hydrocarbons to be below detection limits with trace levels of lower chain

240

hydrocarbons, which typically do not participate in particle formation mechanisms. Also worth

241

noting, is that the observed OC fractions could reflect positive sampling artifacts due to gaseous

242

adsorption of methane and certain lower chain non-methane hydrocarbons onto the pre-fired quartz

243

filters. Table 2 shows the distance-specific EC/OC emissions rate from the two buses over the

244

UDDS and 45 MPH cruise driving cycle and the time-specific emissions rate during idle operation.

245

EC emissions is observed only over the UDDS and idle mode operation. EC fraction was observed

246

in the PM samples from both bus 1 and bus 2 during the UDDS and idle mode operation.

247

Gravimetric filters from idle mode operation of bus 2 also showed signs of discoloration, often

248

indicative of ash or soot emissions in the exhaust. The EC emissions reported from bus 2 over

ACS Paragon Plus Environment

13

Page 15 of 28

Environmental Science & Technology

249

UDDS cycle and idle cycle could be a result of lubrication oil combustion during low load transient

250

operation and extended idle periods respectively.

251

Table 2 EC/OC emissions rate from two test vehicles over the UDDS, 45 MPH cruise and idle

252

operation

Bus 1

Bus 2

mg/mi or mg/sec

UDDS

45 MPH Cruise

Idle

OC

0.489

0.175

0.002

TEC

0.631