Characterization of Polycyclic Aromatic Compounds in Commercial

Feb 12, 2019 - unique elemental compositions, which includes a set of 240 individual PACs. .... connected to a Restek Siltek deactivated guard column ...
0 downloads 0 Views 1MB Size
Subscriber access provided by WEBSTER UNIV

Environmental Measurements Methods

Characterization of polycyclic aromatic compounds in commercial pavement sealcoat products for enhanced source apportionment David T Bowman, Karl J. Jobst, Paul A. Helm, Sonya Kleywegt, and Miriam L. Diamond Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.8b06779 • Publication Date (Web): 12 Feb 2019 Downloaded from http://pubs.acs.org on February 13, 2019

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 34

Environmental Science & Technology

TOC art 84x47mm (300 x 300 DPI)

ACS Paragon Plus Environment

Environmental Science & Technology

1 2 3 4 5 6 7 8 9 10 11 12 13

Characterization of polycyclic aromatic compounds in commercial pavement sealcoat products for enhanced source apportionment David T. Bowman1†, Karl J. Jobst2,3, Paul A. Helm2,4, Sonya Kleywegt2, Miriam L. Diamond1,4* 1Department

of Earth Sciences, University of Toronto, 22 Russell Street, Toronto, Ontario, Canada M5S

3B1 2Ministry of Environment, Conservation and Parks, 125 Resources Road, Toronto, Ontario, Canada M9P 3V6 3Department of Chemistry and Chemical Biology, McMaster University, 1280 Main St.W., Hamilton, Ontario, Canada L8S 4M1 4School of the Environment, University of Toronto, 33 Willcocks St., Toronto, Ontario, M5S 3E8

14

*Corresponding author: Email: [email protected]; Phone: (+1) 416-978-1586.

15

† Current address: SepSolve Analytical, 826 King Street North, Waterloo, Ontario, Canada, N2J 4G8

16

Abstract:

17

Coal tar-based sealcoat (CTSC) products are an urban source of polycyclic aromatic compounds

18

(PACs) to the environment. However, efforts to assess the environmental fate and impacts of

19

CTSC-derived PACs are hindered by the ubiquity of (routinely monitored) PACs released from

20

other environmental sources. To advance source identification of CTSC-derived PACs, we use

21

comprehensive two-dimensional gas chromatography-high resolution mass spectrometry

22

(GC×GC/HRMS) to characterize the major and minor components of CTSC products in

23

comparison to those in other sources of PACs, viz., asphalt-based sealcoat products, diesel

24

particulate, diesel fuel, used motor oil and roofing shingles. GC×GC/HRMS analyses of CTSC

25

products led to the confident assignment of compounds with 88 unique elemental compositions,

26

which includes a set of 240 individual PACs. Visualization of the resulting profiles using Kendrick

27

mass defect plots and hierarchical cluster analysis highlighted compositional differences between

28

the sources. Profiles of alkylated PAHs, and heteroatomic (N,O,S) PACs enabled greater

29

specificity in source differentiation. Isomers of specific polycyclic aromatic nitrogen heterocycles

ACS Paragon Plus Environment

Page 2 of 34

Page 3 of 34

Environmental Science & Technology

30

(PANHs) were diagnostic for coal tar-derived PAC sources. The compounds identified and

31

methods used for this identification are anticipated to aid in future efforts on risk assessment and

32

source apportionment of PACs in environmental matrices.

33 34

Keywords:

35 36

PAHs; GCxGC; comprehensive two-dimensional gas chromatography; environmental forensics; coal tar; Kendrick mass defect

37 38

Graphical Abstract

39

40 41

ACS Paragon Plus Environment

Environmental Science & Technology

42 43 44

INTRODUCTION

45

lots in North America to improve the appearance and to purportedly increase the longevity of

46

asphalt surfaces. The two most common products are: (a) coal tar-based sealcoats (CTSC), and (b)

47

asphalt-based sealcoats (ASC). Polycyclic aromatic hydrocarbon (PAH) concentrations (defined

48

as sum of concentrations of 16 EPA PAHs) are approximately 1000 times higher in CTSC

49

(~66,000 mg kg-1) than in ASC (~50 mg kg-1).1 CTSC products are suspected to be a major source

50

of PAH contamination in urban and suburban areas2–5 and pose potential risks to aquatic life6–10

51

and human health1,3,11. Consequently, CTSC products have been banned in some cities, counties,

52

and states in the United States.1

Pavement sealcoats are black, viscous liquids that are applied to driveways and parking

53

Polycyclic aromatic compounds (PACs) are a diverse collection of compounds which

54

includes PAHs, alkylated-PAHs, and sulfur-, nitrogen-, and oxygen-containing polycyclic

55

aromatic heterocycles (PASHs, PANHs, PAOHs). In addition, PACs with heteroatom-containing

56

functional groups (such as quinones, nitro-PAHs, and hydroxy-PAHs) can also be present in

57

complex PAC mixtures.12 Source apportionment models used to determine the relative

58

contribution of PAHs from CTSC products to lake sediment are often limited to the 16 priority

59

PAHs.2,3,5,13 Alkylated-PAHs and heteroatomic PACs can provide a higher degree of specificity

60

among PAH sources14–17 and are also toxicologically relevant since they are known to exhibit

61

mutagenic properties, in some cases exceeding the mutagenicity of benzo[a]pyrene18–23.

62

Heteroatomic PACs are also expected to exhibit greater mobility and bioavailability in the

63

environment than PAHs due to their increased solubility in water, which in turn increases the risk

64

of exposure to aquatic biota and potentially human exposure through groundwater

65

contamination.24 To date, few studies have reported on the occurrences of alkylated-PAHs and

ACS Paragon Plus Environment

Page 4 of 34

Page 5 of 34

Environmental Science & Technology

66

heteroatomic PACs present in CTSC and ASC products.10,25,26 This reflects the paucity of

67

commercially available reference standards and the limitations of targeted analytical

68

methodologies, often involving extensive sample clean-up and detection by selected ion

69

monitoring. This knowledge gap can be addressed through the development of sensitive, non-

70

targeted analytical methodologies that enable the simultaneous analysis of PAHs, alkyl-PAHs, as

71

well as heteroatomic-PACs and related compounds, whose presence in CTSC products and the

72

environment may not be anticipated beforehand.

73

Comprehensive two-dimensional gas chromatography coupled to mass spectrometry

74

(GC×GC/MS) is a non-targeted analytical technique that offers unparalleled chromatographic

75

resolution and peak capacity.27–30 Novel GC×GC column combinations have been explored to aid

76

in the speciation of (heterocyclic) PACs from sample matrix components.31,32 Profiles generated

77

by GC×GC/MS, sometimes referred to as a ‘chemical fingerprint’, have proven to be vital for

78

source identification31,33 and environmental forensics investigations34,35. GC×GC/MS has been

79

successfully employed for the characterization of PACs (PAHs, alkyl-PAHs, and heteroatomic

80

PACs) in coal tar and coal tar-derived samples.12,36–41 Gallacher et al.12 present a prime example,

81

where they identified 1505 PACs in creosote, including several PASHs and PANHs.

82

The first step to identify an (unknown) contaminant is the determination of the number and

83

type of its constituent elements, viz. its elemental composition. Mass spectrometry (MS) is ideally

84

suited for this task, provided the measurements are performed with sufficient mass accuracy and

85

resolution. However, high resolution MS (HRMS) experiments performed on environmental

86

samples generate enormous datasets, yielding the detection of hundreds to thousands of unique

87

elemental compositions. Kendrick mass defect analyses can greatly assist in the interpretation of

88

high resolution mass spectra, and can distill complex datasets into plots which rapidly distinguish

ACS Paragon Plus Environment

Environmental Science & Technology

89

compounds based on heteroatom content, double bond equivalency, and degree of alkylation.42,43

90

Tian et al.44 exploited this approach to identify 232 PANHs (aza-arenes) in coal tar and creosote

91

contaminated soils.

92

The goal of this study was to identify unique chemical markers in CTSC and ASC products

93

(prior to pavement surface application) to enhance future source apportionment studies and to more

94

reliably identify contamination originating from pavement sealcoat products in complex urban

95

environments. Herein, GC×GC/HRMS was used in conjunction with Kendrick mass defect

96

filtering and hierarchical cluster analysis to identify significant compositional differences between

97

CTSC and ASC products as well as other relevant PAC sources to the urban environment (e.g.,

98

diesel particulate matter, diesel fuel, used motor oil, roofing shingles, and rail road ties). Diverse

99

collections of (alkylated) PAHs, PANHs, PASHs, and PAOHs were identified in the

100

environmental source samples and enabled greater specificity for source identification. The CTSC

101

products contained a unique set of PANHs which could distinguish coal tar-related sources from

102

other PAC sources. The implications of these results to source apportionment are discussed.

103 104

MATERIALS AND METHODS

105

Chemicals and Source Samples.

106

Dichloromethane (DCM, distilled in glass) and toluene (distilled in glass) were purchased

107

from Fisher Chemical (Fair Lawn, NJ, USA) and Caledon Laboratories (Georgetown, Ontario,

108

Canada), respectively. Pavement sealcoats products, consisting of two batches each of CTSC and

109

ASC, were obtained from a major industry provider in the province of Ontario and are

110

representative of materials used in the southern Ontario region. The major ingredients of each

111

product are listed in the SI.

ACS Paragon Plus Environment

Page 6 of 34

Page 7 of 34

Environmental Science & Technology

112

Other representative PAC source samples in this study included: National Institute of

113

Standards and Technology (NIST, Gaithersburg, MD) standard reference materials (SRM 1975,

114

diesel particulate extract; 1597a, complex mixture of PAHs from coal tar), a sample of diesel fuel,

115

a commonly used formulation of used motor oil (10W-30) from a transport truck, asphalt shingles,

116

pot hole repair product from a local building center, coal tar from a transport spill in the region,

117

and a cutting of a rail way tie from a local track, all obtained from southern Ontario, Canada. These

118

additional samples were chosen to represent other potential urban sources which may contribute

119

PAC loadings to the environment.

120 121

Sample Preparation.

122

The sample preparation methods used in this study were based upon previous work

123

reported by Titaley et al.10 Briefly, the pavement sealcoat and pothole repair products were painted

124

onto glass slides and allowed to dry at ambient temperature in the dark for 36 hours. The solid

125

material was then scraped off the glass slide, and transferred to a pre-cleaned amber glass container

126

with a Teflon-lined lid. A standard mixture containing phenanthrene-d10, chrysene-d12, and

127

perylene-d12 (dissolved in dichloromethane) was spiked into the samples. Approximately 100 mg

128

of the dried pavement sealcoat product (ASC and CTSC), railroad ties, pothole filler, and asphalt

129

shingles was extracted using sonication with 15 mL of DCM for 20 minutes (triplicate extraction).

130

The resulting DCM extracts were then centrifuged at 2800 rpm for 30 minutes and the supernatant

131

was transferred to a pre-cleaned amber glass container with a Teflon-lined lid. When necessary,

132

DCM extracts were diluted prior to analysis. Diesel fuel, used motor oil (10W-30), and the NIST

133

standards (diesel particulate and coal tar) were diluted with DCM. Pyrene-d10 (final concentration:

134

20 ppb in toluene) was added as an injection standard to all samples prior to analysis. The percent

ACS Paragon Plus Environment

Environmental Science & Technology

135

recoveries of phenanthrene-d10, chrysene-d12, and perylene-d12 were 81% ± 7, 85% ± 8, 88 % ± 5,

136

respectively. Samples were analyzed by GC×GC/HRMS in triplicate. Method blanks were

137

extracted alongside samples and PACs were not detected in the blanks.

138 139

Instrumentation.

140

GC×GC/HRMS analysis was performed using an Agilent 7890 B gas chromatograph

141

(Agilent Technologies, Santa Clara, CA, USA) equipped with a Zoex ZX2 thermal modulator

142

(Zoex, Houston, TX, USA) and coupled to a Waters Xevo G2-XS quadrupole time-of-flight mass

143

spectrometer (Waters Corp., Milford, MA, USA). The first-dimension column was a DB–5

144

(60 m × 0.25 mm × 0.25 μm film thickness, Agilent) followed by a Restek Siltek deactivated

145

guard column (1 m × 0.15 mm, Restek, Bellenfonte, PA) in the modulator loop. The second-

146

dimension column, Rtx-17sil MS (1 m × 0.15 mm × 0.15 μm film, Restek), was placed in the

147

secondary oven. The secondary column was then connected to a Restek Siltek deactivated guard

148

column 1 m × 0.15 mm, which was inserted into the transfer line. Columns were connected using

149

SilTite μ-Union Connectors (Trajan Scientific and Medical, Victoria, Australia). Additional

150

GC×GC parameters and descriptions of method optimization are included in the SI. The mass

151

spectrometer was operated in the positive mode under atmospheric pressure chemical ionization

152

(APCI) conditions. Mass spectra were collected between 50–1200 amu with a resolving power

153

>20,000 (full width-half maximum) and an acquisition rate of 30 Hz. APCI source conditions are

154

described in the SI. Data processing was performed using GC Image HRMS R2.5 (Zoex) and

155

MassLynx 4.2 (Waters Corp.).

156 157

Atmospheric pressure chemical ionization (APCI) of PACs.

ACS Paragon Plus Environment

Page 8 of 34

Page 9 of 34

Environmental Science & Technology

158

APCI is a soft ionization technique, involving charge exchange between analyte molecules

159

M and N2•+, resulting in the formation of radical cations M•+. Unsubstituted and alkylated PAHs

160

form abundant molecular ions (see Figure S1 of the SI) and protonated adducts [M + H]+ (typically

161

10 to 30% of M•+) due to residual H2O. Collisional cooling minimizes fragmentation and ensures

162

the molecular ions are preserved. This is apparent in the case of 2-ethylanthracene (Figure S1e of

163

the SI), which displayed significantly less fragmentation under APCI than EI. Minor oxygen

164

adducts [M + O]•+ were also formed (relative abundance less than 1% of the molecular ion) by

165

reactions between M•+ and trace O2.45–47 Fortunately, the [M + O]•+ ions resulting from ion-

166

molecule reactions could be distinguished from genuine PAOH compounds. For example, the

167

selected ion chromatogram (SIC) of m/z 218.072 ± 0.003 (Figure S2) displays two clusters of ions

168

identified as C16H10O•+: (i) the [M + O]•+ ion of fluoranthene and pyrene, and (ii) the [M]•+ ion of

169

several benzonaphthofurans. Although the two isobars have similar first dimension retention times,

170

the potential artefact is efficiently separated from the genuine PAOH due to the high resolving

171

power of GC×GC.

172 173

Kendrick mass defect analysis and compound class assignment.

174

A composite mass spectrum was generated for each sample using the GC Image software

175

by creating a ‘blob’ spectrum (mass spectral bin size = 0.003 Da) for the entire chromatogram

176

(chromatographic regions with column bleed excluded). Kendrick mass defect plots were

177

employed to visualize the composite mass spectra and to aid in elemental composition

178

assignment.43,48 Briefly, the mass of each ion (M) was converted to its Kendrick mass (KM):

179

KM = MIUPAC × (14/14.01565)

ACS Paragon Plus Environment

Equation 1

Environmental Science & Technology

180

Note that the mass measurements were obtained using the IUPAC (International Union of Pure

181

and Applied Chemistry) mass scale (i.e. C = 12 amu) and that the factor in equation 1

182

(14/14.01565) was derived from the nominal and exact masses of methylene (CH2). The Kendrick

183

mass defect (KMD) was obtained by subtracting the Kendrick mass (KM) from the nominal

184

Kendrick mass (NKM), which may be approximated by rounding the KM to the nearest integer as

185

KMD = NKM – KM.

186

Kendrick mass defect plots were constructed by graphing MIUPAC vs. KMD (x-axis vs. y-

187

axis) in Microsoft Excel 2010. Elemental compositions were assigned with a standard elemental

188

composition calculator using the following criteria: C0-100, N0-3, O0-3, S0-3. All assignments

189

were within 5 ppm of the theoretical values. Compounds were also sorted into heteroatom classes

190

(using custom macros) to construct heteroatom class histograms. For example, compounds

191

consisting of carbon and hydrocarbon (i.e. PAHs) were categorized in the hydrocarbon (HC) class.

192

Compounds consisting of carbon, hydrocarbon, and sulfur were categorized in the sulfur (S) class.

193

The classification system by Schymanski et al. for the identification of unknowns was used to

194

categorize PACs identified in this study.49 The levels are as follows: Level 1: confirmed structure

195

(by retention times and mass spectrum of reference standard); Level 2: probable structure (by

196

retention index values50–53 and accurate mass); Level 3: tentative structure (by logical elution

197

orders of unknowns relative to known compounds; e.g. isomers elute in bands, and ‘roof-tile’

198

elution pattern of alkylated isomers); and Level 4: molecular formula assignment (by accurate

199

mass).

200 201

Statistical Analysis.

ACS Paragon Plus Environment

Page 10 of 34

Page 11 of 34

Environmental Science & Technology

202

Two-dimensional hierarchical cluster analysis (2D-HCA) was performed using

203

Metaboanalyst 4.0.54 This technique was applied to a dataset containing peak areas (normalized

204

to internal standard) of the 34-EPA PAHs, their alkylated homologues and various parent and

205

alkylated heteroatomic PACs that were present in the CTSC and ASC products. The list of

206

monitored PACs is included Table S1 of the Supporting Information document. In order to reduce

207

the number of analytes included in 2D-HCA plot, the alkylated homologues were reported as a

208

total value by summing the peak areas of all of the isomers. Non-detects were replaced with one

209

half of the lowest value in the dataset. The relative standard deviations of the peak areas of each

210

profiled PAC were < 25%. The dataset was subjected to log transformation and pareto scaling

211

prior to 2D-HCA.

212 213

RESULTS AND DISCUSSION

214

Characterization of PAC profiles in pavement sealcoat products by GC×GC/HRMS.

215

Total ion current (TIC) chromatograms obtained from selected CTSC and ASC products

216

are displayed in Figure 1. The 16 priority PAHs are highlighted on the TIC chromatograms with

217

red boxes. A visual examination of the TICs reveals that the two CTSC products are less complex

218

than the two ASC products. The former consisted predominantly of unsubstituted PAHs as well as

219

their alkylated homologues. The two CTSC products were enriched in: (i) three to four ring PAHs

220

(including, phenanthrene, anthracene, fluoranthene, pyrene, benz[a]anthracene, chrysene), which

221

is consistent with previous studies of CTSCs3,10,25; (ii) five and six ring PAHs (e.g.

222

benzo[b]fluoranthene, benzo[e]pyrene, benzo[a]pyrene, benzo[g,h,i]perylene, indeno[1,2,3-

223

c,d]pyrene, dibenzo[a,h]anthracene); and (iii) several parent PAHs which are not routinely

224

monitored in PAC studies and are excluded from the 16 priority PAH and the expanded 34-PAH

ACS Paragon Plus Environment

Environmental Science & Technology

225

lists, including cyclopenta[def]phenanthrene, cyclopenta[ghi]perylene and indeno[2,1,7-

226

cde]pyrene. Indeno[2,1,7-cde]pyrene has been identified as a major component of a highly

227

mutagenic fraction of a sediment extract.55 Alkylated PAHs, including isomers of methyl-

228

phenanthrene/anthracene, methyl-pyrene/fluoranthene, methyl-chrysene/benzo[a]anthracene, and

229

methyl-benzo[a]pyrene, were also detected and their relative abundance followed a distribution

230

consistent with the pyrogenic origin of coal tar: C0 >> C1 > C2 > C3 > C4.56 Consistent with our

231

results, alkylated PAHs have also been identified in CTSCs2,10 as well as coal tar38,40 and

232

creosote12. The presence of alkylated PAH in CTSC products is of concern because the methylated

233

derivatives of chrysene, benzo[a]anthracene, and benzo[a]pyrene exhibit greater toxicity

234

compared to the parent compound.22,57 Brack and Schirmer55 identified methylated-chrysene

235

isomers (along with heteroatomic compounds, such as dinapthofurans) as major CYP1A-inducers

236

in contaminated sediment.

237

238 239

Figure 1 – GCxGC/HRMS total ion current (TIC) chromatograms of a typical (a) coal tar-based

240

and (b) asphalt-based sealcoat product. The 16 priority PAHs are labelled with red boxes. The

ACS Paragon Plus Environment

Page 12 of 34

Page 13 of 34

Environmental Science & Technology

241

colour scheme of the chromatogram represents the signal intensity: the minimum and maximum

242

intensity values are visualized by the colour transition from white (min.) to blue to green to

243

yellow to red (max.).

244 245

The ASC products consisted of a more diverse set of organic compounds, as witnessed by

246

the complex TIC displayed in Figure 1b. The alkyl PAHs were relatively more abundant than the

247

parent PAHs in the ASC products and displayed a bell-shaped distribution with the maxima

248

observed at C2, C3, or C4, depending on the double bond equivalency (DBE) of the homologous

249

series. This observation is consistent with the petrogenic origin of ASC products.56 PAHs with

250

DBEs of 4 to 17 were detected in the two ASC products at significantly lower concentrations

251

compared to the PAH levels in the two CTSC products.

252

GC×GC/HRMS experiments yielded a large quantity of information and the assignment of

253

elemental compositions and structures to (unknown) peaks is time-consuming. In order to

254

efficiently probe the GC×GC datasets, composite mass spectra were generated from the TIC

255

chromatograms and elemental compositions were assigned based on accurate mass. A total of 88

256

and 337 unique elemental compositions were assigned in the CTSC and ASC products,

257

respectively. As with any complex hydrocarbon mixture, numerous isobars for a given integer

258

mass were detected: for example, five unique elemental compositions shared a nominal mass of

259

272 amu (see Figure S3). Differentiation of these compounds requires both the enhanced

260

separation afforded by GC×GC and accurate mass measurements provided by HRMS. For

261

example, C18H24S+ (m/z 272.1597) and C19H28O+ (m/z 272.2138) co-elute in both the first and

262

second dimensions, but they are readily distinguished by the 54 mDa difference in their exact

263

masses (Figure S4). On the other hand, isobars C21H20+ and C18H24S+ differ in mass by only 3.4

ACS Paragon Plus Environment

Environmental Science & Technology

264

mDa and thus cannot be easily differentiated by mass spectrometry alone. Fortunately, such isobars

265

can be identified if they are separated in the time domain by GC×GC prior to detection.48,58 This

266

is indeed the case for isobars C21H20+ and C18H24S+, as evident from Figure S5.

267 268

Figure 2 - Kendrick mass defect (KMD) plots of (a) a coal tar sealcoat product, and (b) an

269

asphalt sealcoat product.

270 271

Kendrick mass defect plots were used to provide an overview of the identified PAC

272

elemental compositions in selected ASC and CTSC samples (see Figure 2). The elemental

273

compositions displayed differ by carbon number (x-axis), degree of saturation (y-axis), and

274

chemical class (color). The ASC product contained a wider range of (alkylated) PACs. Chemical

275

class histograms were also generated from the composite mass spectra and showed the relative

276

contribution of each compound class (C, N, O, S) for each sample (see Table 1). As expected, the

ACS Paragon Plus Environment

Page 14 of 34

Page 15 of 34

Environmental Science & Technology

277

hydrocarbon class was the most abundant in both of the ASC and CTSC samples. The S class was

278

the second most abundant class in the ASC products, followed by the N class, and the O class. The

279

heteroatoms classes were more relatively abundant in ACS than CTSC products. However, in

280

contrast to the ASC products, CTSC products possessed higher contributions of the N class relative

281

to the S class. These results suggest that the relative proportions of PACs from the heteroatom

282

compound classes may be used to estimate the contributions of ASC and CTSC to environmental

283

samples contaminated with PACs.

284 285 286 287 288

Table 1: The relative compound class contributions obtained from the coal tar sealcoat (CTSC) and asphalt sealcoat (ASC) extracts. The abundance of each chemical class was normalized to the total ion current. Sample

289

CTSC 1 CTSC 2 ASC 1 ASC 2

Hydrocarbon Oxygen Class Class (HC) (O) 94.1 1.8 94.0 2.2 74.3 0.8 85.8 0.5

Sulfur Class (S) 1.5 1.3 22.3 13

Nitrogen Class (N) 2.6 2.5 2.6 0.7

290 291

Identification of heteroatomic PACs in pavement sealcoat products.

292

Table S2 summarizes the number of PASHs that were identified in the CTSC and ASC

293

products. The ASC products were enriched in a larger collection of PASHs (see Table 1 and Figure

294

3a), due to the increased sulfur content of petroleum asphalt.17 Abundant PASHs include the parent

295

and alkylated homologues of dibenzothiophene (DBE = 9), phenanthrothiophenes (DBE = 11),

296

and benzonaphthothiophene (DBE = 12). A number of high molecular weight PASHs with DBE

297

values of 14 and 15 were also identified in both of the ASC products (Level 449). The two

298

commercial CTSC products contained a suite of PASHs with DBE values of 9 to 14 (see Figure

ACS Paragon Plus Environment

Environmental Science & Technology

299

3b). Abundant PASHs in the CTSC samples included dibenzothiophene (Level 1, DBE = 9),

300

phenanthro[4,5-bcd]thiophene (Level 2, DBE = 11), and isomers of benzonaphthothiophene

301

(Level 2, DBE = 12). Trace amounts of several compounds tentatively identified as isomers of

302

benzo[2,3]phenanthro[4,5-bcd]thiophene (Level 4, DBE = 14) were also detected in the CTSC

303

products.

304

ACS Paragon Plus Environment

Page 16 of 34

Page 17 of 34

305 306 307 308

Environmental Science & Technology

Figure 3 - Double bond equivalency vs carbon number plots for the sulfur class (a: ASC, b: CTSC), nitrogen class (c: ASC, d: CTSC), and oxygen class (e: ASC, f: CTSC). The size of the circles are proportional to the relative abundance of each elemental composition.

309

ACS Paragon Plus Environment

Environmental Science & Technology

310

The CTSC samples contained a collection of PANHs with DBEs of 9 to 14 (see Figure 3d

311

and Table S3). Carbazole was the most abundant compound identified in the N chemical class

312

(Level 1)49. Benzo[def]carbazole was also tentatively identified in the samples by RI and accurate

313

mass (Level 2). Benzo[lmn]phenanthridine (Level 2) and indeno[1,2,3-ij]isoquinoline (Level 2),

314

as well as four additional structural isomers (Level 3), were also tentatively identified by RIs and

315

logical elution orders in both of the CTSC samples. Lastly, benz[c]acridine and benz[a]acridine

316

were identified in the two CTSC samples (Level 2). The aza-arenes were not as frequently detected

317

in the ASC products in comparison to the CTSC products (Figure 3c). Carbazole and alkylated

318

(carbon numbers: C9 to C20; Levels 2 and 3) homologues were detected in one of the ASC products,

319

displaying a petrogenic distribution. In addition, unsubstituted (Level 2) and alkylated (Level 3)

320

benzocarbazole homologues (petrogenic distribution) were identified in the ASC products. Nitro-

321

PAHs were not detected in the ASC or CTSC products tested, but they have been detected by

322

others in CTSCs using more extensive clean-up procedures.10

323

Table S4 lists the PAOHs that were identified in the pavement sealcoat samples.

324

Dibenzofuran (C12H8O, DBE = 9) was identified in the two CTSC samples (Level 1), along with

325

C1- and C2-dibenzofuran homologues (Level 3). Several (alkylated) benzonaphthofuran and

326

pyrenofuran homologues were also identified in both of the CTSC samples (Levels 2/3). The ASC

327

products contained PAOHs with similar DBE values as the CTSC products, but the alkylated

328

homologues were present in higher relative proportions in the ASCs. In addition, a suite of

329

compounds tentatively identified as C0-dinapthofuran (C20H12O), and C1-dinapthofuran (C21H14O)

330

were detected in the ASC products based on accurate mass (Level 4). Dinaphthofurans have been

331

identified as major CYP1A-inducers in contaminated sediment.55 Hydroxyl-PAHs were not

ACS Paragon Plus Environment

Page 18 of 34

Page 19 of 34

Environmental Science & Technology

332

detected in any of the CTSC or ASC sealcoat samples, but trimethylsilylation derivatization could

333

be used to improve their detection.12,59

334

335 336

Figure 4 - Two-dimensional hierarchical cluster analysis with heat map plot of various

337

environmental PAH sources. Red and blue colors represent the most intense and least intense

ACS Paragon Plus Environment

Environmental Science & Technology

338

relative abundance values (log scale), respectively. The relative abundances in the heat map plot

339

are presented as an average of 3 replicates.

340 341

Source Identification

342

PAC profiles of the CTSC and ASC products, as well as other environmental sources of

343

PACs that we analyzed (viz. asphalt shingles, rail road ties, coal tar, used motor oil, diesel fuel and

344

diesel particulate matter), were compared by 2D-HCA (Figure 4). Cluster analysis along the x-axis

345

of the heatmap revealed relationships between the source samples based on relative peak areas of

346

the profiled analytes. The samples separated into two main groups: petrogenic (ASC, asphalt

347

shingles, motor oil, diesel) and pyrogenic sources (CTSC, coal tar, rail road ties, and diesel

348

particulate matter). As expected, this differentiation was primarily driven by the greater relative

349

abundance of alkylated PAHs and alkylated heterocyclic PACs in the petrogenic sources. As

350

discussed above, PAC mixtures with a petrogenic origin contain alkylated homologues which

351

follow a bell-shaped distribution, while the pyrogenic samples are enriched in unsubstituted PAHs.

352

This phenomenon is well known and is often exploited in environmental forensic studies to

353

identify samples of petrogenic origin.56

354

The petrogenic source samples were further separated into two additional clusters: (i)

355

asphalt-derived samples (n = 3: ASC products and shingles), and (ii) a cluster containing diesel

356

fuel (n = 1) and used motor oil (n = 1). The diesel fuel and used motor oil samples were

357

distinguished from the asphalt samples because they did not contain any PANHs, or high molecular

358

weight PAOHs (i.e. pyrenofuran, dinaphthofuran). Diesel was distinguished from used motor oil

359

since it contained a lighter fraction of PAHs; the heaviest PAHs detected in diesel and used motor

360

oil possessed DBE values of 13 and 17, respectively.

ACS Paragon Plus Environment

Page 20 of 34

Page 21 of 34

Environmental Science & Technology

361

The pyrogenic samples were differentiated into two clusters: coal tar-derived samples

362

(n=5) and diesel particulate (n=1, NIST 1975). The diesel particulate sample was characterized by:

363

(i) a relatively high abundance of PAOHs, including dibenzofurans, benzonaphthofuran, and

364

naphthoxanthene as well as many other O-heterocycles not detected in the other samples

365

considered in this study (the O class represented 16% of total intensity of diesel particulate); (ii) a

366

low relative abundance of some high molecular weight PAHs; and (iii) very low levels of PASHs

367

compared to the coal tar-related samples, which is consistent with the findings of Wilson et al.60

368

In addition, the coal tar-related sources contained a more diverse collection of PANHs than diesel

369

particulate, as well as the other environmental sources included in this study (see Fig. 3 and S6).

370

Selected PANHs were detected exclusively in the coal tar-related samples, such as isomers

371

of benzoacridine (Level 2), methyl-benzoacridine (Level 3), and 4H-Naphtho[1,2,3,4-

372

def]carbazole (Level 4). Isomers of benzocarbazole were detected in a number of the PAC source

373

(diesel particulate, and the coal tar- and asphalt-related samples); however, a comparison of the

374

isomer profiles (Figure 5) revealed significant differences between the source samples.

375

Benzocarbazoles have previously been identified in creosote12 and coal tar41. Three isomers of

376

benzocarbazole (benzo[a]carbazole, isomer ‘a’; benzo[b]carbazole, isomer ‘b’; benzo[c]carbazole,

377

isomer ‘c’; mass spectra and retention times of aforementioned analytes are found in Figure S7)

378

were consistently detected in the coal tar-derived samples, but were absent in the diesel particulate

379

matter sample. While the three isomers were detected in all of the asphalt-related source samples,

380

the isomers were found in differing relative proportions than the coal tar-related samples. It is clear

381

from the extracted ion chromatograms (Figure 5) that benzo[b]carbazole was found in lower

382

proportions relatively to the other isomers in the asphalt-related source samples. The compounds

383

tentatively identified as isomers of methyl-benzocarbazole (Level 3) provided another

ACS Paragon Plus Environment

Environmental Science & Technology

384

distinguishing feature, since they were enriched in the asphalt samples and were absent or near

385

detection limits in the coal tar-related samples. Further exploration of PAC isomer profiles is

386

expected to generate more diagnostic PAC source profiles and potentially enable greater

387

specificity of PAC source identification.

388 389

390 391 392 393 394 395

Figure 5 - Isomer profiles of benzocarbazole (C16H11N) and methyl-benzocarbazole (C17H13N) in (a) CTSC product 1, (b) CTSC product 2, (c) Coal tar (NIST 1597a), (d) Coal tar, (e) Rail road ties, (f) diesel particulate, (g) ASC product 1, (h) ASC product 2, and (i) asphalt shingles. Note: isomers ‘a’, ‘b’, and ‘c’ were identified as benzo[a]carbazole, benzo[b]carbazole, and benzo[c]carbazole, respectively, based on retention index values and accurate mass measurements.

396 397 398

Environmental Significance and Implications for Future Studies.

399

PAH-contamination in sediments is a world-wide problem. Knowledge of sources of the

400

contamination is needed to reduce levels, however, efforts to distinguish between different PAH

401

sources are complicated by the ubiquity of the 16 priority PAHs that are typically measured.61 The

402

analytical methods developed here can be used to trace sources of PAHs based on the relative

ACS Paragon Plus Environment

Page 22 of 34

Page 23 of 34

Environmental Science & Technology

403

abundances of (alkylated) PAHs and heteroatomic (N, O, S) PACs present in pavement sealcoat

404

products and numerous other environmental sources.

405

Analyses of the composite mass spectrum obtained from the CTSC products led to the

406

assignment of 240 PACs with 88 unique elemental compositions. The profiling of this diverse

407

collection of compounds significantly improved the ability to differentiate PAC source samples.

408

Notably, petrogenic and pyrogenic sources could be easily distinguished based on relative

409

contributions from alkylated PAHs and PASHs. It was also shown that PANHs, such as

410

benzocarbazoles, were very useful for the distinction of CTSC products from other pyrogenic and

411

petrogenic sources. These results follow from a previous study by Mahler et al.26, in which they

412

analyzed run off from ASC- and CTSC-coated parking lots and reported that elevated

413

concentrations of five low molecular weight PANHs (quinoline, isoquinoline, acridine,

414

phenanthridine, carbazole) in run-off were associated with the use of CTSCs. High molecular

415

weight PANHs have also recently been identified as abundant PACs in sediment samples

416

associated with coal tar contamination44, further supporting their applicability as markers in PAC

417

source apportionment studies.

418

The improved characterization of PACs by GC×GC/HRMS is expected to aid in the risk

419

assessment of pavement sealcoat products. Current risk assessment methods for the evaluation of

420

PACs are based on the chemical analysis of the 16 priority PAHs and, consequently, overlook

421

other toxicologically relevant PACs. Larsson et al.24 demonstrated that the concentrations of the

422

16 priority PAHs could only account for a small proportion of the bio-assay-determined toxicity

423

of remediated soil samples. GC×GC/HRMS analyses in this study revealed the presence of a

424

number of PACs in the pavement sealcoat products the toxicity of which is known to equal or

425

exceed the toxicity of benzo[a]pyrene. For example, both of the ASC and CTSC products

ACS Paragon Plus Environment

Environmental Science & Technology

426

contained PASHs (e.g. phenanthro[3,4-b]thiophene, benzo[2,3]phenanthro[4,5-bcd]thiophene)

427

and alkylated PAHs which have been reported to be toxic in previous studies.18,20,22,57 Furthermore,

428

a number of polar PACs (such as PANHs or PAOHs) were identified in both of the sealcoat

429

products. The polar fractions (containing heteroatomic PACs) of both ASC and CTSC products

430

have been shown to be acutely toxic by the embryonic zebrafish (Danio rerio) development

431

toxicity test.10 Polar PACs possess higher water solubilities than their PAH counterparts and,

432

therefore, such compounds pose a risk in leaching events.24 Historically, ASC products have been

433

deemed as a safer alternative to CTSCs since they contain significantly lower concentrations of

434

the 16 priority PAHs4,62, are not mutagenic10, and have been reported to pose fewer human and

435

biological health concerns1. However, due the abundance of individual alkylated-PAHs and

436

heteroatomic-PACs in the mixture, there is a critical need to better understand the persistence,

437

toxicity, and environmental fate and behavior of PACs present in such products, as the use of ASCs

438

is expected to increase in the future.

439

While the method developed and presented here has enabled the identification of promising

440

markers of CTSC contamination, we note that there may well be additional source-diagnostic

441

PACs whose polarity inhibits analysis using GCxGC, and may instead be discovered through

442

derivatization or by LC-MS. The characterization of polar PACs, such as phenols, would be

443

beneficial since such compounds have been noted to be of toxicological relevance and, due to their

444

enhanced water solubilities, are more bioavailable than their PAH-analogues.12

445 446

Supporting Information

ACS Paragon Plus Environment

Page 24 of 34

Page 25 of 34

Environmental Science & Technology

447

SI contains additional details concerning chemical analysis and products analyzed. Figures

448

S1-S6 show ion chromatographs and details of compounds analyzed, and Tables S1- S4 list

449

compounds identified.

450 451

Acknowledgements:

452

Funding was provided by the Government of Ontario (Grant #2304). Such support does not

453

indicate endorsement by the Government of Ontario of the contents of this contribution. The

454

authors are grateful to Eric J. Reiner and Jack Cochran for enlightening discussions on GC×GC.

455

References:

456

(1)

Mahler, B. J.; Metre, P. C. Van; Crane, J. L.; Watts, A. W.; Scoggins, M.; Williams, E. S.

457

Coal-Tar-Based Pavement Sealcoat and PAHs: Implications for the Environment, Human

458

Health, and Stormwater Management. Environ. Sci. Technol. 2012, 46, 3039–3045.

459

(2)

Mahler, B. J.; Van Metre, Peter, C.; Bashara, T. J.; Wilson, J. T.; Johns, D. A. Parking Lot

460

Sealcot: An Unrecognized Source of Urban Polycyclic Aromatic Hydrocarbons.

461

Envionmental Sci. Technol. 2005, 39 (15), 5560–5566.

462

(3)

and Other Sources to 40 U.S. Lakes. Sci. Total Environ. 2010, 409 (2), 334–344.

463 464

Van Metre, P. C.; Mahler, B. J. Contribution of PAHs from Coal-Tar Pavement Sealcoat

(4)

Van Metre, P. C.; Mahler, B. J.; Wilson, J. T. PAHs Underfoot: Contaminated Dust from

465

Coal-Tar Sealcoated Pavement Is Widespread in the United States. Environ. Sci. Technol.

466

2009, 43 (1), 20–25.

467 468

(5)

Witter, A. E.; Nguyen, M. H.; Baidar, S.; Sak, P. B. Coal-Tar-Based Sealcoated Pavement: A Major PAH Source to Urban Stream Sediments. Environ. Pollut. 2014, 185,

ACS Paragon Plus Environment

Environmental Science & Technology

59–68.

469 470

(6)

and Ultraviolet Radiation to Ambystoma Maculatum. Ecotoxicity 2010, 19, 1147–1156.

471 472

(7)

(8)

Bryer, P. J.; Scoggins, M.; McClintock, N. L. Coal-Tar Based Pavement Sealant Toxicity to Freshwater Macroinvertebrates. Environ. Pollut. 2010, 158 (5), 1932–1937.

475 476

Bommarito, T.; Sparling, D. W.; Halbrook, R. S. Toxicity of Coaltar and Asphalt Sealants to Eastern Newts, Notophthalmus Viridescens. Chemosphere 2010, 81, 187–193.

473 474

Bommarito, T.; Sparling, D. W.; Halbrook, R. S. Toxicity of Coaltar Pavement Sealants

(9)

Scoggins, M.; McClintock, N. L.; Gosselink, L.; Bryer, P. Occurrence of Polycyclic

477

Aromatic Hydrocarbons below Coal-Tar-Sealed Parking Lots and Effects on Stream

478

Benthic Macroinvertebrate Communities. J. N. Benthol. Soc. 2007, 26 (4), 694–707.

479

(10)

Titaley, I. A.; Chlebowski, A.; Truong, L.; Tanguay, R. L.; Massey Simonich, S. L.

480

Identification and Toxicological Evaluation of Unsubstituted PAHs and Novel PAH

481

Derivatives in Pavement Sealcoat Products. Environ. Sci. Technol. Lett. 2016, 3, 234–242.

482

(11)

Williams, E. S.; Mahler, B. J.; Van Metre, P. C. Cancer Risk from Incidental Ingestion

483

Exposures to PAHs Associated with Coal-Tar-Sealed Pavement. Environ. Sci. Technol.

484

2013, 47 (2), 1101–1109.

485

(12)

Gallacher, C.; Thomas, R.; Taylor, C.; Lord, R.; Kalin, R. M. Comprehensive

486

Composition of Creosote Using Comprehensive Two-Dimensional Gas Chromatography

487

Time-of-Flight Mass Spectrometry (GCxGC-TOFMS). Chemosphere 2017, 178, 34–41.

488 489

(13)

Huang, L.; Chernyak, S. M.; Batterman, S. A. PAHs (Polycyclic Aromatic Hydrocarbons), Nitro-PAHs, and Hopane and Sterane Biomarkers in Sediments of Southern Lake

ACS Paragon Plus Environment

Page 26 of 34

Page 27 of 34

Environmental Science & Technology

Michigan, USA. Sci. Total Environ. 2014, 487 (1), 173–186.

490 491

(14)

Mccarry, B. E.; Allan, L. M.; Legzdins, A. E.; Lundrigan, J. A.; Marvin, C. H.; Bryant, D.

492

W. Thia-Arenes as Pollution Source Tracers in Urban Air Particulate. Polycycl. Aromat.

493

Comp. 1996, 11 (1–4), 75–82.

494

(15)

Marvin, C. H.; Mccarry, B. E.; Villella, J.; Allan, L. M.; Bryant, D. W. Chemical and

495

Biological Profiles of Sediments as Indicators of Sources of Genotoxic Contamination in

496

Hamilton Harbour. Part I: Analysis of Polycyclic Aromatic Hydrocarbons and Thia-Arene

497

Compounds. Chemosphere 2000, 41 (7), 979–988.

498

(16)

Sofowote, U. M.; McCarry, B. E.; Marvin, C. H. Source Apportionment of PAH in

499

Hamilton Harbour Suspended Sediments: Comparison of Two Factor Analysis Methods.

500

Environ. Sci. Technol. 2008, 42 (16), 6007–6014.

501

(17)

Stout, S. A.; Emsbo-Mattingly, S. D.; Douglas, G. S.; Uhler, A. D.; McCarthy, K. J.

502

Beyond 16 Priority Pollutant PAHs: A Review of PACs Used in Environmental Forensic

503

Chemistry. Polycycl. Aromat. Comp. 2015, 35, 285–315.

504

(18)

Pelroy, R. A.; Stewart, D. L.; Tominaga, Y.; Iwao, M.; Castle, R. N.; Lee, M. L. Microbial

505

Mutagenicity of 3- and 4-Ring Polycyclic Aromatic Sulfur Heterocycles. Mutat Res 1983,

506

117 (1–2), 31–40.

507

(19)

Cambridge University Press: Cambridge, 1990.

508 509 510

Jacob, J. Sulfur Analogues of Polycyclic Aromatic Hydrocarbons (Thiaarenes);

(20)

Kropp, K.; Fedorak, P. A Review of the Occurrence, Toxicity, and Biodegradation of Condensed Thiophenes Found in Petroleum. Can. J. Microbio. 1998, 44, 605–622.

ACS Paragon Plus Environment

Environmental Science & Technology

511

(21)

Admiraal, W. Toxicity of Azaarenes. Rev Env. Contam Toxicol 2002, 173, 39–83.

512 513

Bleeker, E. A.; Wiegman, S.; de Voogt, P.; Kraak, M.; Leslie, H. A.; de Haas, E.;

(22)

Lam, M. M.; Bülow, R.; Engwall, M.; Giesy, J. P.; Larsson, M. Methylated PACs Are

514

More Potent than Their Parent Compounds: A Study of Aryl Hydrocarbon Receptor–

515

mediated Activity, Degradability, and Mixture Interactions in the H4IIE-Luc Assay.

516

Environ. Toxicol. Chem. 2018, 37, 1409–1419.

517

(23)

Lam, M. M.; Engwall, M.; Denison, M. S.; Larsson, M. Methylated Polycyclic Aromatic

518

Hydrocarbons and/or Their Metabolites Are Important Contributors to the Overall

519

Estrogenic Activity of Polycyclic Aromatic Hydrocarbon–contaminated Soils. Environ.

520

Toxicol. Chem. 2018, 37 (2), 385–397.

521

(24)

Larsson, M.; Lam, M. M.; van Hees, P.; Giesy, J. P.; Engwall, M. Occurrence and

522

Leachability of Polycyclic Aromatic Compounds in Contaminated Soils: Chemical and

523

Bioanalytical Characterization. Sci. Total Environ. 2018, 622–623, 1476–1484.

524

(25)

Van Metre, P. C.; Majewski, M. S.; Mahler, B. J.; Foreman, W. T.; Braun, C. L.; Wilson,

525

J. T.; Burbank, T. L. PAH Volatilization Following Application of Coal-Tar-Based

526

Pavement Sealant. Atmos. Environ. 2012, 51, 108–115.

527

(26)

Mahler, B. J.; Van Metre, P. C.; Foreman, W. T. Concentrations of Polycyclic Aromatic

528

Hydrocarbons (PAHs) and Azaarenes in Runoff from Coal-Tar- and Asphalt-Sealcoated

529

Pavement. Environ. Pollut. 2014, 188, 81–87.

530 531

(27)

Liu, Z.; Phillips, J. B. Comprehensive Two-Dimensional Gas Chromatography Using an On-Column Thermal Modulator Interface. J. Chromatogr. Sci. 1991, 29 (6), 227–231.

ACS Paragon Plus Environment

Page 28 of 34

Page 29 of 34

532

Environmental Science & Technology

(28)

Phillips, J. B.; Beens, J. Comprehensive Two-Dimensional Gas Chromatography: A

533

Hyphenated Method with Strong Coupling between the Two Dimensions. J. Chromatogr.

534

A 1999, 856 (1–2), 331–347.

535

(29)

Gas Chromatography. Trends Anal. Chem 2002, 21 (9–10), 573–583.

536 537

Marriott, P.; Shellie, R. Principles and Applications of Comprehensive Two-Dimensional

(30)

Mondello, L.; Tranchida, P. Q.; Dugo, P.; Dugo, G. Comprehensive Two-Dimensional

538

Gas Chromatography-Mass Spectrometry: A Review. Mass Spectrom. Rev. 2008, 27,

539

101–124.

540

(31)

Manzano, C. A.; Muir, D.; Marvin, C. Separation of Thia-Arenes and Aza-Arenes from

541

Polycyclic Aromatics in Snowpack Samples from the Athabasca Oil Sands Region by

542

GC×GC/ToF-MS. Int. J. Environ. Anal. Chem. 2016, 96 (10), 905–920.

543

(32)

Manzano, C.; Hoh, E.; Simonich, S. L. M. Improved Separation of Complex Polycyclic

544

Aromatic Hydrocarbon Mixtures Using Novel Column Combinations in GCxGC/ToF-

545

MS. Environ. Sci. Technol. 2012, 46 (14), 7677–7684.

546

(33)

Manzano, C. A.; Marvin, C.; Muir, D.; Harner, T.; Martin, J.; Zhang, Y. Heterocyclic

547

Aromatics in Petroleum Coke, Snow, Lake Sediments, and Air Samples from the

548

Athabasca Oil Sands Region. Environ. Sci. Technol. 2017, 51 (10), 5445–5453.

549

(34)

Megson, D.; Reiner, E. J.; Jobst, K. J.; Dorman, F. L.; Robson, M.; Focant, J.-F. A Review

550

of the Determination of Persistent Organic Pollutants for Environmental Forensics

551

Investigations. Anal. Chim. Acta 2016, 941, 10–25.

552

(35)

Gruber, B.; Weggler, B. A.; Jaramillo, R.; Murrell, K. A.; Piotrowski, P. K.; Dorman, F.

ACS Paragon Plus Environment

Environmental Science & Technology

553

L. Comprehensive Two-Dimensional Gas Chromatography in Forensic Science: A Critical

554

Review of Recent Trends. Trends Anal. Chem 2018, 105, 292–301.

555

(36)

McGregor, L. A.; Gauchotte-Lindsay, C.; Daéid, N. N.; Thomas, R.; Daly, P.; Kalin, R.

556

M. Ultra Resolution Chemical Fingerprinting of Dense Non-Aqueous Phase Liquids from

557

Manufactured Gas Plants by Reversed Phase Comprehensive Two-Dimensional Gas

558

Chromatography. J. Chromatogr. A 2011, 1218 (29), 4755–4763.

559

(37)

McGregor, L. A.; Gauchotte-Lindsay, C.; Nic Daéid, N.; Thomas, R.; Kalin, R. M.

560

Multivariate Statistical Methods for the Environmental Forensic Classification of Coal

561

Tars from Former Manufactured Gas Plants. Environ. Sci. Technol. 2012, 46 (7), 3744–

562

3752.

563

(38)

Koolen, H. H. F.; Swarthout, R. F.; Nelson, R. K.; Chen, H.; Krajewski, L. C.; Aeppli, C.;

564

McKenna, A. M.; Rodgers, R. P.; Reddy, C. M. Unprecedented Insights into the Chemical

565

Complexity of Coal Tar from Comprehensive Two-Dimensional Gas Chromatography

566

Mass Spectrometry and Direct Infusion Fourier Transform Ion Cyclotron Resonance Mass

567

Spectrometry. Energy Fuels 2015, No. 29, 641–648.

568

(39)

Gallacher, C.; Thomas, R.; Lord, R.; Kalin, R. M.; Taylor, C. Comprehensive Database of

569

Manufactured Gas Plant Tars. Part A. Database. Rapid Commun. Mass Spectrom. 2017,

570

31 (15), 1231–1238.

571

(40)

Gallacher, C.; Thomas, R.; Lord, R.; Kalin, R. M.; Taylor, C. Comprehensive Database of

572

Manufactured Gas Plant Tars. Part B. Aliphatic and Aromatic Compounds. Rapid

573

Commun. Mass Spectrom. 2017, 31 (15), 1239–1249.

574

(41)

Gallacher, C.; Thomas, R.; Lord, R.; Kalin, R. M.; Taylor, C. Comprehensive Database of

ACS Paragon Plus Environment

Page 30 of 34

Page 31 of 34

Environmental Science & Technology

575

Manufactured Gas Plant Tars. Part C. Heterocyclic and Hydroxylated Polycyclic Aromatic

576

Hydrocarbons. Rapid Commun. Mass Spectrom. 2017, 31, 1250–1260.

577

(42)

Spectrometry of Organic Compounds. Anal. Chem. 1963, 35 (13), 2146–2154.

578 579

Kendrick, E. A Mass Scale Based on CH = 14.0000 for High Resolution Mass

(43)

Hughey, C. a.; Hendrickson, C. L.; Rodgers, R. P.; Marshall, a. G.; Qian, K. Kendrick

580

Mass Defect Spectrum: A Compact Visual Analysis for Ultrahigh-Resolution Broadband

581

Mass Spectra. Anal. Chem. 2001, 73 (19), 4676–4681.

582

(44)

Tian, Z.; Vila, J.; Wang, H.; Bodnar, W.; Aitken, M. D. Diversity and Abundance of

583

High-Molecular-Weight Azaarenes in PAH-Contaminated Environmental Samples.

584

Environ. Sci. Technol. 2017, 51 (24), 14047–14054.

585

(45)

Jobst, K. J.; De Winter, J.; Flammang, R.; Terlouw, J. K.; Gerbaux, P. Differentiation of

586

the Pyridine Radical Cation from Its Distonic Isomers by Ion-Molecule Reactions with

587

Dioxygen. Int. J. Mass Spectrom 2009, 286, 83–88.

588

(46)

Fernando, S.; Green, M. K.; Organtini, K.; Dorman, F.; Jones, R.; Reiner, E. J.; Jobst, K.

589

J. Differentiation of (Mixed) Halogenated Dibenzo-p-Dioxins by Negative Ion

590

Atmospheric Pressure Chemical Ionization. Anal. Chem. 2016, 88 (10), 5205–5211.

591

(47)

Megson, D.; Ortiz, X.; Jobst, K. J.; Reiner, E. J.; Mulder, M. F. A.; Balouet, J.-C. A

592

Comparison of Fresh and Used Aircraft Oil for the Identification of Toxic Substances

593

Linked to Aerotoxic Syndrome. Chemosphere 2016, 158, 116–123.

594 595

(48)

Bowman, D. T.; Jobst, K. J.; Ortiz, X.; Reiner, E. J.; Warren, L. A.; McCarry, B. E.; Slater, G. F. Improved Coverage of Naphthenic Acid Fraction Compounds by

ACS Paragon Plus Environment

Environmental Science & Technology

596

Comprehensive Two-Dimensional Gas Chromatography Coupled with High Resolution

597

Mass Spectrometry. J. Chromatogr. A 2017, 1536, 88–95.

598

(49)

Schymanski, E. L.; Jeon, J.; Gulde, R.; Fenner, K.; Ruff, M.; Singer, H. P.; Hollender, J.

599

Identifying Small Molecules via High Resolution Mass Spectrometry: Communicating

600

Confidence. Environ. Sci. Technol. 2014, 48, 2097–2098.

601

(50)

Lee, M. L.; Vassilaros, D. L.; White, C. M.; Novotny, M. Retention Indices for

602

Programmed-Temperature Capillary-Column Gas Chromatography of Polycyclic

603

Aromatic Hydrocarbons. Anal. Chem. 1979, 51 (6), 768–773.

604

(51)

Vassilaros, D. L.; Kong, R. C.; Later, D. W.; Lee, M. L. Linear Retention Index System

605

for Polycyclic Aromatic Compounds: Critical Evaluation and Additional Indices. J.

606

Chromatogr. A 1982, 252, 1–20.

607

(52)

Wise, S. A.; Benner, B. A.; Byrd, G. D.; Chesler, S. N.; Rebbert, R. E.; Schantz, M. M.

608

Determination of Polycyclic Aromatic Hydrocarbons in a Coal Tar Standard Reference

609

Material. Anal. Chem. 1988, 60 (9), 887–894.

610

(53)

Coal Liquids and Shale Oils. Anal. Chem. 1981, 53 (3), 400–407.

611 612

Willey, C.; Iwao, M.; Castle, R. N.; Lee, M. L. Determination of Sulfur Heterocycles in

(54)

Chong, J.; Soufan, O.; Li, C.; Caraus, I.; Li, S.; Bourque, G.; Wishart, D. S.; Xia, J.

613

MetaboAnalyst 4.0: Towards More Transparent and Integrative Metabolomics Analysis.

614

Nucleic Acids Res 2018, 46 (W1), W486–W494.

615 616

(55)

Brack, W.; Schirmer, K. Effect-Directed Identification of Oxygen and Sulfur Heterocycles as Major Polycyclic Aromatic Cytochrome P4501A-Inducers in a Contaminated

ACS Paragon Plus Environment

Page 32 of 34

Page 33 of 34

Environmental Science & Technology

Sediment. Environ. Sci. Technol. 2003, 37 (14), 3062–3070.

617 618

(56)

Academic Press: San Diego, CA, 2015.

619 620

Murphy, B. L.; Morrison, R. D. Introduction to Environmental Forensics, 3rd ed.;

(57)

Calle, L. M.; Sullivan, P. D.; Nettleman, M. D.; Ocasio, I. J.; Blazyk, J.; Jollick, J.

621

Antioxidants and the Mutagenicity of Benzo(a) Pyrene and Some Derivatives. Biochem.

622

Biophys. Res. Commun. 1978, 85 (1), 351–356.

623

(58)

Byer, J. D.; Siek, K.; Jobst, K. Distinguishing the C3 vs SH4 Mass Split by

624

Comprehensive Two-Dimensional Gas Chromatography–High Resolution Time-of-Flight

625

Mass Spectrometry. Anal. Chem. 2016, 88 (12), 6101–6104.

626

(59)

Gauchotte-Lindsay, C.; Richards, P.; McGregor, L. A.; Thomas, R.; Kalin, R. M. A One-

627

Step Method for Priority Compounds of Concern in Tar from Former Industrial Sites:

628

Trimethylsilyl Derivatisation with Comprehensive Two-Dimensional Gas

629

Chromatography. J. Chromatogr. A 2012, 1253, 154–163.

630

(60)

Wilson, W. B.; Hayes, H. V.; Campiglia, A. D.; Wise, S. A. Qualitative Characterization

631

of Three Combustion-Related Standard Reference Materials for Polycyclic Aromatic

632

Sulfur Heterocycles and Their Alkyl-Substituted Derivatives via Normal-Phase Liquid

633

Chromatography and Gas Chromatography/Mass Spectrometry. Anal. Bioanal. Chem.

634

2018, 410 (17), 4177–4188.

635

(61)

Andersson, J. T.; Achten, C. Time to Say Goodbye to the 16 EPA PAHs? Toward an Up-

636

to-Date Use of PACs for Environmental Purposes. Polycycl. Aromat. Compd. 2015, 35

637

(2–4), 330–354.

ACS Paragon Plus Environment

Environmental Science & Technology

638

(62)

Mahler, B. J.; Van Metre, P. C.; Wilson, J. T.; Musgrove, M.; Burbank, T. L.; Ennis, T.

639

E.; Bashara, T. J. Coal-Tar-Based Parking Lot Sealcoat: An Unrecognized Source of PAH

640

to Settled House Dust. Environ. Sci. Technol. 2010, 44 (3), 894–900.

641

ACS Paragon Plus Environment

Page 34 of 34