Comprehensive Evaluation of Mercury Photocatalytic Oxidation by

Mar 22, 2017 - To meet these needs, titanium dioxide (TiO2) has been used to remove Hg0 effectively ..... by the variation of SO2 concentration when N...
0 downloads 0 Views 1MB Size
Subscriber access provided by UNIV OF REGINA

Article

A comprehensive evaluation of mercury photocatalytic oxidation by cerium-based TiO2 nanofibers Lulu Wang, Yongchun Zhao, and Junying Zhang Ind. Eng. Chem. Res., Just Accepted Manuscript • DOI: 10.1021/acs.iecr.6b04995 • Publication Date (Web): 22 Mar 2017 Downloaded from http://pubs.acs.org on March 27, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Industrial & Engineering Chemistry Research is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 25

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

A Comprehensive Evaluation of Mercury Photocatalytic Oxidation by Cerium-Based TiO2 Nanofibers

Lulu Wang, Yongchun Zhao*, Junying Zhang*

State Key Laboratory of Coal Combustion, Huazhong University of Science & Technology, Wuhan 430074, PR China * E-mail: [email protected][email protected]

Abstract Efficient and economical technologies are essential to the control of mercury, the emission of which imposes serious health concerns and environmental risks. Photocatalysis is an attractive method for reducing mercury emissions. Considering that titania is widely applied in the photodegradation of toxic contaminants, this study investigated the removal of mercury over cerium-based titania nanofibers (CBTs) at low temperature. According to the results, in the atmosphere containing SO2, both catalyst and UV proposed adverse effect on Hg0 oxidation. The competition between SO2 and Hg0 for active sites as well as the formation of cerium sulfate are responsible for the deactivation of Hg0 removal capacity. More interestingly, without O2, NO and HCl still exerted a superior promoting effect on mercury removal. Entirely different from the properties under SO2, UV and catalyst both facilitated Hg0 oxidation with the existence of HCl. Meanwhile, effects of the copresence of NO and SO2 on Hg0 removal were further investigated. NO was the most dominant gas component enhancing the removal capacity. Considerable high removal efficiency (>80%) was observed in the presence of 300 ppm NO and 400 ppm SO2. These indicate that combining photocatalysis technology with CBTs is a promising strategy to oxidize mercury under low-rank coal combustion flue gas in which the concentration of HCl is relatively low.

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Keywords: Nanofiber; Photocatalytic oxidation; Elemental mercury

1. Introduction Due to the extreme toxicity, persistence and bioaccumulation, emission of mercury has become a major environmental issue that attracts global concerns. Coal combustion has been targeted as one of the most significant anthropogenic sources of mercury emissions to the atmosphere1,2. Together, three countries, China, India and the United States are responsible for about 65.39% of the global emission of mercury from coal burning3–5. Established on 19 March, 2013, Minamata Convention on Mercury is a significant boost to prevent releases of mercury with global and legally binding agreements between countries6. Among the different forms of mercury present in the coal-fired atmosphere, gaseous elemental mercury (Hg0) is more difficult to remove using currently available air pollution control devices (APCDs) due to its high volatility, inertness, and insolubility in water7. Unfortunately, Hg0 is the dominant mercury species emitted to the atmosphere, i.e. Hg0 contributed 66-94% of total mercury released from coal-fired power plants in China8. This arouses urgent needs for efficient and economical technologies to reduce Hg0 emission. To meet these needs, titanium dioxide (TiO2) has been used to remove Hg0 effectively in the presence of UV9. Hg0 was adsorbed and oxidized on the activated TiO2 surface by hydroxyl (OH) radicals generated under UV irradiation: Ti − OH • + Hg → HgOH + OH • → HgO + H 2 O

(1)

In addition, Lee and co-workers10–13 deduced that during the irradiation by UV light, active sites were generated on a titania particle surface to adsorb Hg and thus form a complex (TiO2•HgO(complex)) on TiO2. Consequently, the Hg-containing TiO2 nanoparticles were readily removed when the flue gases passed through APCDs. However, the large bandgap energy of 3.2 eV limits the application of TiO2, which could only be excited by UV light (λ < 365 nm) irradiation. Subsequently, many modification techniques have been investigated to enlarge the application of TiO2, such as noble metal loading14, transition metal ion doping15,

ACS Paragon Plus Environment

Page 2 of 25

Page 3 of 25

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

and metal and non-metal codoping16. Compared with noble metal catalysts, the lower-cost transition metal catalysts also exhibit good performance. Kaluza9,17 found that elemental mercury can be photo-oxidized by titania, zinc oxide, tin oxide, and cerium oxide, and the maximum excitation wavelengths have been tabulated. CeO2, which is abundant, nontoxic as well as inexpensive, emerges as an attractive candidate. However, pure CeO2 is thermally unstable, and fortunately, this shortcoming could be overcome through the introduction of Ti4+, which would help enhance the stability by forming cerium-based titania (CBT)18. Traditionally, coal-fired flue gas contains some constituents such as O2, SO2, NOx, HCl and water vapor. These components are believed to play crucial roles on Hg0 removal due to the complex reactions involved. However, their effects are still enigmatic. By calculating, Xie et al19. demonstrated that an addition of 300 ppm NO only exhibited a very slight promotional effect on mercury removal, while further increase in the concentration caused no significant variation. In contrast, Chen20 deduced that NO drastically reduced Ecap of mercury under various light irradiations. A pilot-scale photocatalytic Hg0 emission control system was installed at a real combustion facility and results showed that lower ηHg was due to the various acid gases present21. As a consequence, a systematic study of the effects of those components, including NO, on Hg0 photocatalytic removal is essential. It is worthy of study due to the emissions of these compounds, especially SO2, NOx and mercury, pose significant challenges to the environment and public health. Meanwhile, the interaction mechanisms among UV, catalyst and flue gas are complicated, which need to be further identified. Considering the problems mentioned above, the present study aims to (i) elucidate the photocatalytic properties of Hg0 removal over CBTs, (ii) clarify the mechanisms involved, and (iii) explain the synergistic effects of acidic gases on Hg0 photocatalytic oxidation. Also, the study propose possible strategies for the simultaneous removal of SO2, NO and mercury by photocatalysis technology.

2. Experimental 2.1 Sample preparation and analysis In this work, the cerium-based TiO2 nanofibers (shorted by CBTs) were obtained by an electrospinning method. The design of CBTs exhibits the distinct advantages of large surface area, high crystallinity and excellent geometrical flexibility, which favors photocatalytic activity. The precursor solution was a mixture of

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

tetrabutyl titanate (TBOT) with ethanol and acetic acid. The volume ratio of them was 1:5:2. Subsequently, cerium nitrate and an appropriate amount of polyvinyl pyrrolidone (Mw =1,300,000) were slowly dissolved in the above solution and stirred for several hours to obtain a homogeneous mixture. The loading value of Ce on the CBTs was defaulted as 0.3%, which presented optimal Hg0 removal activity in air combustion atmosphere. The obtained solution was then loaded into a syringe and ready for electrospinning. The detailed operating procedures have been described in our earlier studies22. Additionally, the resulting nanofibers were calcined at 400 °C in static air. The crystalline structures of samples were identified through X-ray powder diffractometer (XRD, PANalytical B.V.X’Pert PRO). The BET surface areas of samples were obtained via N2 isothermal adsorption (Micromeritics ASAP 2000). Further analysis regarding functional groups was carried out with the X-ray photoelectron spectroscopy (XPS, AXIS-ULTRA DLD-600W) as well as the Fourier-transform infrared spectrometer (FTIR, VERTEX 70). 2.2 Experimental apparatus and procedure As shown in Figure 1, the test unit consists of a gas feeding system, a fixed bed reactor and a set of analytical instruments including flue gas and Hg0 analyzers. Flow rates of all the individual flue gas components were accurately controlled by mass flow controllers with a total flow rate of 1 L min-1. Hg0 vapor was introduced into the gas mixing chamber using high-purity N2 (99.999%) from a Hg0 permeation tube immersed in a water bath at fixed temperature, and the initial concentration was 50 µg·m-3. Experiments were performed in a fixed-bed reactor consisting of an inner quartz tube and an outer quartz tube. Irradiations were performed with a low- pressure UV lamp (Philips, TUV PL-S 9W, Japan), which was placed in the inner tube. The primary wavelength of light emitted by the lamp was 253.7 nm. The light intensity was 3 mW/cm2, while the UV energy density (Ed) was fixed at 540 J/L. Cold air was generated by an air pump efficiently to cool the lamp and help maintain a constant reaction temperature at 120 °C. Effluent gas from the photochemical reactor flowed through an impinger containing 10% NaOH(aq). Furthermore, a moisture trap was installed downstream of the impinger to remove water vapor from the gas stream and prevent interference in mercury detection. The Hg0 concentration was continuously monitored using a VM-3000 Mercury Vapor Monitor (Mercury Instrument, Germany). Changes in the concentrations of NO, NO2 and SO2 were analyzed by a flue gas analyzer (OPTIMA7, YORK INSTRUMENTS LTD). Finally, the exhaust was passed through a carbon

ACS Paragon Plus Environment

Page 4 of 25

Page 5 of 25

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

trap before released into a fume hood. All connecting tubes were made of Teflon to avoid corrosion and minimize mercury species adsorption23. Furthermore, it should not be ignored that duplicated experiments were conducted to guarantee the reproducibility and validity of the results.

Figure 1. Schematic diagram of mercury oxidation fixed bed system. Eight sets of experiments were carried out, as summarized in Table 1. Individual gas or combinations of the gases were added to the baseline blend. Set I was designed to figure out the effect of O2 on Hg0 removal. In Set II and Set III, Hg0 oxidation properties in the presence of SO2 were investigated. Set IV ~ Set VII were conducted to identify the effect of NO, HCl and H2O on Hg0 oxidation, respectively. The aim of Set VIII was to confirm the coexistence of NO and SO2 on Hg0 oxidation, which would help elucidate the interactions between SO2, NO and Hg0.

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Table 1 Experimental conditions for activity measurement of the catalysts. Experiments

Reaction conditions

Set I

CBTs, UV, N2 + 0, 4%, 8% O2.

Set II

(i) without catalyst, UV; (ii) without UV, CBTs; (iii) UV, CBTs. N2/O2/SO2.

Set III

(i) CBTs, UV, N2 + 400, 800, 1200 ppm SO2; (ii) CBTs with Hg0 preloaded, pure N2.

Set IV

(i) N2 + 50, 100, 200, 300 ppm NO; (ii) BFG + 300 ppm NO. CBTs, UV.

Set V

(i) without catalyst, UV; (ii) without UV, CBTs; (iii) UV, CBTs. N2/O2/HCl.

Set VI

(i) N2 + 30, 50 ppm HCl; (ii) BFG + 50 ppm HCl. CBTs, UV.

Set VII

CBTs, UV, N2 + 2%, 4% H2O.

Set VIII

(i) 1200 ppm SO2 + 50 ~ 300 ppm NO; (ii) 300 ppm NO + 400 ~1200 ppm SO2. CBTs, UV. °

Temperature was 120 C, BFG (Baseline Flue Gas): 4% O2/N2 mixture, inlet Hg0 concentration was about 50 µg·m-3, the dosage of catalyst in each experiment was 0.3 g.

2.3 Data Processing Before testing Hg0 removal over the nanofibers, blank experiments were conducted to eliminate any possible interference from the system. The results showed interference in Hg0 detection by the empty reactor was verified to be negligible. Furthermore, during each test, the gas stream firstly bypassed the fixed-bed reactor until a stable inlet concentration of Hg0 was obtained. The Hg0 removal efficiency (η) was quantified by the following formula:

η=

CHg0inlet - CHg0outlet CHg0inlet

*100%

(2)

Where CHg0inlet and CHg0outlet represent the concentrations of Hg0 measured at the inlet and outlet of the reactor, respectively.

ACS Paragon Plus Environment

Page 6 of 25

Page 7 of 25

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

Photon utilization efficiency is the primary factor which determines the effectiveness of photolytic and photocatalytic oxidation processes. Therefore, an appropriate analysis of the photocatalytic oxidation of Hg0 should be carried out in terms of quantum yield: Φ=

⋕     ⋕   

In the present study, A = B=



=

, 

(3) !"

$%

(4) (5)

&

Where Cin,Hg0 is the inlet concentration of Hg0 (µg/m3), Q the flue gas flow (L/min), t the running time per each experiment (in minutes), M the atomic mass of Hg (g/mol), and NA the Avogadro constant. For B, S is the irradiated area (cm2), ℎ the Planck constant, ( the frequency of light irradiation, and I the light intensity. I could be measured by the light radiometer.

3. Results and discussion 3.1 Interference of flue gas constituents on mercury analyzer To investigate the influence of flue gas constituents on Hg0 measurement under UV light irradiation, various kinds of gases were introduced to the reaction system successively. As shown in Figure 2, in the entire experimental duration, the instantaneous value of Hg0 fluctuated at 0±0.4 µg·m-3, which is well smaller than the detection limit of the automatic mercury analyzer. This indicates that the interference of flue gas on Hg0 analyzer under UV light was negligible. We could further infer that the variations of Hg0 observed in this study were due to the interaction between catalyst, Hg0 and flue gas atmosphere. It is noted that a catalyst and a sorbent are closely related species, and that a catalyst typically first adsorbs mercury before oxidizing it, resulting in initial transient removals of mercury observed by the analyzer24–26. The BET surface area of CBTs was 258.67 m2/g in the present study.

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 2. Interference of flue gas constituents on mercury measurement. 3.2 Effect of individual flue gas constituents on Hg0 photocatalytic oxidation The various flue gas components individually flowed into the reactor. Adding the acidic/oxidizing gas constituent one at a time into the carrier gas caused variation in Hg0 oxidation capacity. Effects of flue gas atmosphere on Hg0 oxidation and the reaction pathways over CBTs are summarized in Figure 3, in which BFG was defined as the O2/N2 mixture. The quantum yield (QY, the number of photons utilized for a desired chemical reaction divided by the number of photons absorbed by the catalyst) for TiO2 was 16.26%. In particular, the addition of 0.3% Ce into TiO2 achieved a higher quantum yield of Hg0 reduction (44.69%).

ACS Paragon Plus Environment

Page 8 of 25

Page 9 of 25

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

Figure 3. Effect of individual flue gas constituents on Hg0 photocatalytic oxidation at 120 °C. 3.2.1 Effect of O2 on Hg0 oxidation About 38.66% Hg0 removal efficiency was achieved under pure N2 gas flow. Surface oxygen played a significant role in this condition. As ceria-based oxides acquire their oxygen storage capability via a Ce4+Ce3+ process27, the loss of Hg0 under this condition was due to the reaction between Hg0 and stored oxygen, which was a combination of lattice oxygen and chemisorbed oxygen. Overall, the UV radiation and the abundant surface oxygen on the catalyst were responsible for the performance under N2 atmosphere. When 4% O2 was introduced to the N2 gas stream, ƞ increased to around 89.95%. Further increase in the concentration leads to higher η. It is not difficult to find that O2 played a significant role in Hg0 oxidation over CBTs. Gas-phase O2 regenerated the lattice oxygen and replenished the chemisorbed oxygen28, which had been consumed in the photochemical reaction, and thus enhanced Hg0 removal. 3.2.2 Effect of SO2 on Hg0 oxidation Apart from SO2, UV and catalyst could also affect Hg0 oxidation. Experiments were designed to reveal the possible interaction between them, as shown in Figure 4. In the atmosphere containing SO2, CBTs had adverse effects on Hg0 oxidation. It should be noted that UV also decreased ƞ, which is in contrast to the widely

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 10 of 25

accepted view that UV irradiation could activate sample and facilitate Hg0 removal. To explore the involved mechanism, semi-quantitative XPS analysis of the spent catalyst was conducted (inset of Figure 4). With the irradiation of UV light, the peak found at 168.7 eV was stronger than that without UV, which was assigned to sulfate (SO42-). In other words, more SO2 react with catalyst in the presence of UV, resulting in the deactivation of Hg0 oxdiation performance.

Figure 4. Photocatalytic properties in the presence of SO2 (Inset was the S 2p spectra of spent catalyst). It can be seen from Figure 3 that SO2 suppressed Hg0 oxidation. When 800 ppm SO2 was added to N2, η decreased from 30.34% to 25.55% and further decreased to 24.15% with SO2 content increasing up to 1200 ppm. It is reasonable to conclude that Hg0 oxidation over CBTs coincides with the Langmuir-Hinshelwood mechanism, where reactive sites on catalyst surface react with adjacently adsorbed Hg0 to form Hg2+. And this is in satisfactory agreement with the findings in literature29. Firstly, a desorption experiment was designed to illustrate the negative impact of SO2, the results of which are shown in Figure 5. CBTs were saturated by Hg0 at 120 °C with N2 as the carrier gas for several hours. During this process, the Hg0 concentration displaying on the mercury analyzer decreased at first and then rose up slowly, which was a result of adsorption. Therefore, when mercury concentration was the same as the original value, it indicated that the catalyst had reached its largest adsorption capacity. When this steady state lasted for some time, Hg0 was cut off and adding SO2 at the same time. A spike was observed, as depicted in Figure 5. Without the feeding of SO2, Hg0 concentration just

ACS Paragon Plus Environment

Page 11 of 25

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

decreased directly. It indicates that SO2 inhibited Hg0 adsorption. Therefore, it is not difficult to find that the competition adsorption between Hg0 and SO2 was responsible for the deactivation of CBTs. More encouragingly, after adding SO2, the Hg0 concentration increased gently, just from 50 µg·m-3 to 60.7 µg·m-3, which is quite smaller than other literature30 and makes our CBTs so unique. It can be deduced that our sample could reach its adsorption saturation quickly. This performance is well in line with some studies31.

Figure 5. Desorption of Hg0 from catalyst by SO2. Secondly, SO2 might also react with the CBTs to form thermally stable cerium sulfate, which is responsible for the deactivation of Hg0 removal capacity. XPS spectra of S 2p was then performed to provide more specific information, and results are described in Figure 6. Compared with the fresh catalyst, the S peaks for spent samples mainly centered at 168.7 eV, which can be assigned to sulfate (SO42-). As a consequence, SO42- species have been considered as strong-binding species that will inhibit Hg0 oxidation.

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 12 of 25

Figure 6. XPS spectra of S 2p for fresh and spent catalyst. 3.2.3 Effect of NO on Hg0 oxidation To probe into the influence of NO on mercury removal, Figure 3 also compares Hg0 removal efficiencies in pure N2 and NO/N2 mixture. Firstly, this test indicates that η was 53.10% for the gas flow containing 50 ppm NO. Further increase in the concentration to 300 ppm resulted in an even higher η of 78.10%. The presence of Ce4+ on CBTs was reported to accelerate the oxidation of NO to NO232. Secondly, in the presence of O2, a significant higher η was obtained. With the aid of O2, more adsorbed NO can be oxidized on the CBTs to form abundant active species like NO+ and NO2, which are active for Hg0 oxidation33. Moreover, the consumed surface oxygen could be replenished by the gas-phase O2. Interestingly, η increased up to almost 100% (99.27% actually) when just 4% O2 was introduced to gas flow. Furthermore, this number is also higher than that in the 4%O2/N2 mixture, indicating again that NO possessed a promoting effect on Hg0 oxidation. To identify the possible mechanisms, the species of flue gas components at the outlet of the reactor were detected by an online gas analyzer. About 39 ppm of NO2 was detected. Moreover, additional experiments were conducted. During the additional tests, NO2 concentrations at the outlet of the reactor were determined by gas analyzer with Hg0 feeding flowed over catalysts and free of Hg0, respectively. Results showed that the concentration of NO2 free of Hg0 was higher than that with Hg0 feeding. It is reasonable to conclude that NO2 could cause Hg0 oxidation. This is entirely consistent with Huang’s point of view, which evidenced that low concentration of NO2 could heterogeneously react with Hg034.

ACS Paragon Plus Environment

Page 13 of 25

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

Figure 7. FTIR spectra of the spent catalyst. Besides the above tests, wide survey FTIR spectra were adopted to identify the functional groups, as summarized in Figure 7. When oxygen was introduced, the peak at 1384 cm-1 sharply increased, which could be assigned to nitrite or nitrate species. The broad peak in the range of 1458-1577 cm-1 could be regarded as a series of successive peaks, and they could be assigned to NO2-containing species, like chemisorbed NO2, Obond NO2 and NO3 species, which would facilitate Hg0 oxidation on the surface of the catalyst35. Subsequently, the band at 1654 cm-1 might be assigned to nitrate species36. It can be clearly seen that the detection of NO2containing species, which generated from the reaction between NO and active surface oxygen, may be responsible for the Hg0 oxidation over CBTs. This is consistent with the experimental results. Meanwhile, the formation of nitrate happened in the reaction of these species. This might be connected with a series of reactions, such as those listed below: NO(g) + O 2 → NO 2 (g) + O

(6)

Hg 0 ( g ) + O → HgO

(7)

Hg

O

( g ) + 2 O + 2 NO

2

→ Hg ( NO 3 ) 2

(8)

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

(a)

(b)

Page 14 of 25

(c)

Figure 8. XPS of O 1s and Ce 3d for (a) fresh catalyst, (b) spent catalyst under NO, (c) spent catalyst under NO/O2. Analysis of XPS spectra was conducted to provide more specific information, and the results were depicted in Figure 8. The O 1s peak of fresh catalyst is resolved into three component peaks, which achieved an acceptable fit in the XPS spectra. The primary peak at ca. 529.85 eV, ca. 532.02 eV, and ca. 533.44 eV can be assigned to lattice oxygen in TiO2, surface hydroxyl groups and adsorbed oxygen, respectively. Compared with fresh catalyst, peak positions of the spent catalyst under NO are basically the same. After adding O2 to the atmosphere, the areas of the primary peaks changed apparently, indicating the change of relative concentration. As depicted in Figure 8 (c), the concentrations of surface hydroxyl groups and adsorbed oxygen increased, which may originate from the replenishment of gas-phase O2. The XPS spectra of Ce 3d can be divided into eight peaks, the bands labeled u1 and v1 represent the 3d104f1 initial electronic state corresponding to Ce3+, while the peaks labeled u, u2, u3, v, v2 and v3 represent the 3d104f0 state of Ce4+ ions37. There is no denying that the co-existence of Ce3+/Ce4+ can provide advantageous charge imbalance and give rise to oxygen vacancies38. On the other hand, ceria-based oxides acquire their oxygen storage capacity via this redox reaction27, thus the lattice oxygen defects over CBTs surface can also be improved. 3.2.4 Effect of HCl on Hg0 oxidation

ACS Paragon Plus Environment

Page 15 of 25

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

HCl is also found crucial to Hg0 removal39,40. Figure 9 depicts the interaction between UV, HCl and catalyst on Hg0 oxidation. Quite different from the properties under SO2, UV and CBTs both enhance Hg0 oxidation with the existence of HCl. HCl was reported to sharply promote Hg0 oxidation, even when the catalyst had been saturated with adsorbed mercury40,41. Xie et al.19 and Wang et al.42 provided a fundamental perspective into HCl and believed that Hg0 is not directly oxidized by HCl since it is already in a reduced state. Under pure N2 atmosphere, the Hg0 removal efficiency over the catalyst was even lower in the presence of HCl. Niksa et al.43 further demonstrated that Hg0 oxidation by HCl requires the existence of oxygen.

Figure 9. Photocatalytic properties in the presence of HCl. But in the present study, the effect of HCl on Hg0 oxidation was investigated in the presence of O2 alone, HCl alone and both HCl and O2, as summarized in Figure 3. In the presence of HCl alone, 30 ppm HCl balanced in N2 resulted in η of 75.42%, which is obviously higher than that under pure N2. Lattice oxygen and/or chemisorbed oxygen were responsible for the transformation of HCl to Cl2 or other active chlorine species, which promoted Hg0 oxidation19,44. More interestingly, Ce-based oxides acquire their oxygen storage capability via the Ce4+Ce3+ process27, which is significant for Hg0 removal by HCl in the absence of O2. η increased rapidly when HCl concentration further increased to 50 ppm, which is almost the same as the result in the Hg/O2/N2 atmosphere. Increasing HCl content resulted in additional generations of [Cl], which denotes an active chlorine species for oxidizing Hg0. Under this condition, the possible reaction between CBTs and HCl possibly occurs through31:

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

2CeO2 + 2 HCl ↔ Ce2O3 + 2[Cl ] + H 2O

Page 16 of 25

(9)

With the aid of O2, the Hg0 removal efficiency reached 95.88%, indicating that CBTs are extremely efficient for Hg0 heterogeneous oxidation by 50 ppm HCl. By inference, the Deacon process may well explain Hg0 oxidation in the presence of HCl, which was also enlighted by Du et al.45. Hg0 reacted with active chlorine species to form Hg2+, which could be adsorbed onto catalyst surface46,47(e.g. Eqs. (10)-(12)).

4HCl + O2 → 4[Cl ] + 2H 2O

(10)

Hg 0 + [Cl ] → HgCl

(11)

HgCl + [Cl ] → HgCl2

(12)

3.2.5 Effect of H2O on Hg0 oxidation Water vapor is regarded as an inevitable component of coal combustion flue gas. It has been found to hinder Hg removal48,49, and the same inhibitive effect was observed over CBTs in this work. The introduction of 2% H2O into pure N2 resulted in a negligible reduction of removal efficiency. An addition of 4% H2O led to about 3% declination of η. The negative impact was to some extent due to the competition between water vapor and Hg0 for active sites, which restrained the Hg0 adsorption. This competitive adsorption for active sites may also prohibit the adsorption of reactive species such as NO and [Cl] in the actual flue gas system, which are more important components affecting Hg0 oxidation. Additionally, the adsorbed water vapor may react with SO3 and CeO2 to form sulfate, which could cover the surface of the catalysts and hinder the Hg0 removal by deactivating the catalysts to a certain extent50. Nevertheless, it should be noted that the reduction of η in the presence of H2O over CBTs was minor, indicating that our product has excellent resistance to H2O. Furthermore, this series of tests were to investigate the effects of individual flue gas components on Hg0 oxidation. Thus, only 0.30g of CBTs were used in each test. Accordingly, this disadvantage could be offset by using more catalysts. Fortunately, the electrospinning method we adopted to prepare samples is a highly versatile method that allows the fabrication of continuous fibers with diameters ranging from micrometer to nanometer51. In addition, the promotional effects of O2, NO

ACS Paragon Plus Environment

Page 17 of 25

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

and HCl in a simulated flue gas atmosphere, as previously demonstrated, may outweigh the negative impact of H2O. This is very favorable for application in the actual flue gas system, where water vapor is unavoidable. 3.3 Effects of the coexistence of SO2 and NO on Hg0 photocatalytic oxidation SO2 and NO are simultaneously presented in the actual flue gas. However, their concentrations will change with coal species and combustion conditions of the boiler52. Importantly, they have significant influences on the Hg0 removal43. Furthermore, understanding the interactions between them is an essential part of the simultaneous removal of SO2, NO and mercury through an integrated process. So a series of experiments with various concentrations of NO and SO2 were carried out. As depicted in Figure 10, when 1200 ppm SO2 and 50 ppm NO were introduced to the reaction system, η significantly increased to 41.76%. Further increase in NO concentration to 300 ppm resulted in an even higher efficiency of 81.44%. NO again was observed to significantly enhance the Hg0 oxidation capacity of CBTs, which is well in line with the trend in the presence of NO alone (Figure 3). Moreover, the results also show that the average removal efficiency of Hg0 in the coexistence of SO2 and NO is better than that in the presence of SO2 alone. A similar phenomenon was also found in previous studies53 and they reached that Hg0 secondary volatile was effectively prevented, since NO was eventually oxidized to NO3-, which would react with Hg0 to form more stable Hg(NO3)2 or Hg(NO3)2•H2O compared with Hg2+.

Figure 10. Hg0 oxidation with 1200 ppm SO2 and various NO concentrations.

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 18 of 25

A further experiment was also conducted with specific NO content and various SO2 concentrations (Figure 11). Baseline 1 and 2 represented pure N2 atmosphere, 300 ppm NO/N2 mixture, respectively. According to the results, the coexistence of NO and 400 ppm of SO2 led to a better performance (80.83%) than that from baseline 1 (24.54%), and comparable to that from baseline 2 (78.10%). This means that about 400 ppm of SO2 in flue gas is to the benefit of removing Hg0. Although SO2 alone showed a deteriorating effect on Hg0 oxidation, the removal efficiency of Hg0 was almost unaffected by the variation of SO2 concentration when NO coexisted with SO2, suggesting that the competition reaction between SO2/NO and Hg0 for the oxidants was not serious. NO was the most dominant gas component enhancing the Hg0 oxidation capacity for CBTs in the tested flue gases. Results again showed that the presence of NO and SO2 improved the Hg0 oxidation. Furthermore, the enhancements caused by the coexistence of these two acidic gases were more significant than those by individual component.

Figure 11. Hg0 oxidation with 300 ppm NO and various SO2 concentrations. Based on the analysis above, influences of the coexistence of NO and SO2 on Hg0 oxidation were revealed. 300 ppm NO and 400 ppm SO2 were sufficient for the removal of Hg0, so the optimal parameters were also established. It should be emphasized that the tests were conducted without HCl. In other words, Hg0 can be efficiently oxidized over CBTs in the absence of HCl. This distinguishing feature is of tremendous value for Hg0 oxidation under low-rank coal combustion flue gas, which usually comes with low concentration of HCl. Knowledge learned from this part would help elucidate the synergistic effects of acidic gases on Hg0

ACS Paragon Plus Environment

Page 19 of 25

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

photocatalytic oxidation. Such studies are of fundamental importance in developing effective pollution control technologies and devices in which the simultaneous removal of SO2, NO and Hg0 through an integrated process is possible.

4. Conclusions This work has elucidated the influences of flue gas components on Hg0 removal by photocatalysis technology, and clarified the mechanisms involved. Results reported herein demonstrate that in the atmosphere containing SO2, both CBTs and UV had negative effect on Hg0 oxidation. The competition between SO2 and Hg0 for active sites as well as the formation of cerium sulfate are both responsible for the deactivation of Hg0 removal in the presence of SO2. In contrast, the detection of NO2-containing species generated from the reaction promoted Hg0 conversion. Quite different from the properties under SO2, UV and CBTs enhanced Hg0 oxidation with the existence of HCl. Moreover, effects of coexistence of NO and SO2 on Hg0 removal were further investigated. The results indicate that NO significantly enhanced the Hg0 oxidation capacity of CBTs. In the absence of HCl, the competition reaction between SO2/NO and Hg0 for the oxidants was not serious. This distinguishing feature is of tremendous value for Hg0 removal under low-rank coal combustion flue gas. Consequently, it is a promising method to enhance Hg0 conversion over CBTs under UV irradiation. Coalderived flue gas is a complex mixture containing fly ash particles, oxygen, moisture, carbon monoxide and many acid gases. A typical untreated flue gas derived from the combustion of a US Low Sulfur Eastern bituminous coal can contain: 5-7% H2O, 3-4% O2, 15-16% CO2, 1 ppb total Hg, 20 ppm CO, 10 ppm hydrocarbons, 100 ppm HCl, 800 ppm SO2, 10 ppm SO3, 500 ppm NOx, and balance N25,54–56. There can be potential impacts of other acid gases such as SO3, as well as carbon monoxide and particulates, upon the Hg oxidation, and this could be a fruitful area for future study and research. Also, the potential deactivation of the catalyst over time by flue gas species such as SO2, SO3, and Hg also merits further examination.

Supporting Information

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 20 of 25

The Supporting Information is available free of charge on the ACS Publications website at http: //pubs.acs.org. Details on XRD and TEM analysis of samples.

Notes The authors declare no competing financial interest.

Acknowledgments This project was supported by the National Key Basic Research and Development Program (No. 2014CB238904). The authors would like to express their thanks to the China Scholarship Council (CSC) and the Department of Analytical and Testing Center at Huazhong University of Science and Technology for providing financial support and the sample analysis, respectively.

References

(1) Zhang, A.; Zhang, Z.; Lu, H.; Liu, Z.; Xiang, J.; Zhou, C.; Xing, W.; Sun, L. Effect of Promotion with Ru Addition on the Activity and SO2 Resistance of MnOx–TiO2 Adsorbent for Hg0 Removal. Ind. Eng. Chem. Res. 2015, 54, 2930. (2) Wang, Y.; Duan, Y.; Yang, L.; Zhao, C.; Shen, X.; Zhang, M.; Zhuo, Y.; Chen, C. Experimental Study on Mercury Transformation and Removal in Coal-Fired Boiler Flue Gases. Fuel Process. Technol. 2009, 90, 643. (3) UNEP. Global Mercury Assessment 2013: Sources, Emissions, Releases and Environmental Transport. UNEP Chemicals Branch, Geneva, Switzerland 2013. (4) Granite, E. J.; Pennline, H. W.; Hargis, R. A. Novel Sorbents for Mercury Removal from Flue Gas. Ind. Eng. Chem. Res. 2000, 39, 1020. (5) Granite, E. J.; Pennline, H. W. Photochemical Removal of Mercury from Flue Gas. Ind. Eng. Chem. Res. 2002, 41, 5470. (6) Han, L.; Meng, H.; Wang, J.; Hu, Y.; Bao, W.; Chang, L.; Wang, H. Application of Spent H2S Scavenger of Iron Oxide in Mercury Capture from Flue Gas. Ind. Eng. Chem. Res. 2016, 55, 5100. (7) Zhang, A.; Xiang, J.; Sun, L.; Hu, S.; Li, P.; Shi, J.; Fu, P.; Su, S. Preparation, Characterization, and Application of Modified Chitosan Sorbents for Elemental Mercury Removal. Ind. Eng. Chem. Res. 2009, 48, 4980.

ACS Paragon Plus Environment

Page 21 of 25

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

(8) Wang, S. X.; Zhang, L.; Li, G. H.; Wu, Y.; Hao, J. M.; Pirrone, N.; Sprovieri, F.; Ancora, M. P. Mercury Emission and Speciation of Coal-Fired Power Plants in China. Atmos. Chem. Phys. 2010, 10, 1183. (9) Granite, E. J.; King, W. P.; Stanko, D. C.; Pennline, H. W. The Implications of Mercury Interactions with Band-Gap Semiconductor Oxides. Main Group Chem. 2008, 7, 227. (10) Lee, T. G.; Biswas, P.; Hedrick, E. Overall Kinetics of Heterogeneous Elemental Mercury Reactions on TiO2 Sorbent Particles with UV Irradiation. Ind. Eng. Chem. Res. 2004, 43, 1411. (11) Lee, T. G.; Hyun, J. E. Structural Effect of the in Situ Generated Titania on Its Ability to Oxidize and Capture the Gas-Phase Elemental Mercury. Chemosphere 2006, 62, 26. (12) Lee, Y. G.; Park, J.-W.; Kim, J.-H.; Min, B. R.; Jurng, J.; Kim, J.; Lee, T. G. Comparison of Mercury Removal Efficiency from a Simulated Exhaust Gas by Several Types of TiO2 under Various Light Sources. Chem. Lett. 2004, 33, 36. (13) Lee, T. G.; Biswas, P.; Hedrick, E. Comparison of Hg0 Capture Efficiencies of Three in Situ Generated Sorbents. AIChE J. 2001, 47, 954. (14) Chan, C. C.; Chang, C. C.; Hsu, W. C.; Wang, S. K.; Lin, J. Photocatalytic Activities of Pd-Loaded Mesoporous TiO2 Thin Films. Chem. Eng. J. 2009, 152, 492. (15) Xu, Y.; Lei, B.; Guo, L.; Zhou, W.; Liu, Y. Preparation, Characterization and Photocatalytic Activity of Manganese Doped TiO2 Immobilized on Silica Gel. J. Hazard. Mater. 2008, 160, 78. (16) Iliev, V.; Tomova, D.; Rakovsky, S. Nanosized N-Doped TiO2 and Gold Modified Semiconductors-Photocatalysts for Combined UV–Visible Light Destruction of Oxalic Acid in Aqueous Solution. Desalination 2010, 260, 101. (17) U. Kaluza, H.P. Boehm. Titanium Dioxide Catalyzed Photooxidation of Mercury. J. Catal. 1971, 22, 347. (18) Luo, M.; Chen, J.; Chen, L.; Lu, J.; Feng, Z.; Li, C. Structure and Redox Properties of CexTi1-xO2 Solid Solution. Chem. Mater. 2001, 13, 197. (19) Xie, Y.; Li, C.; Zhao, L.; Zhang, J.; Zeng, G.; Zhang, X.; Zhang, W.; Tao, S. Experimental Study on Hg0 Removal from Flue Gas over Columnar MnOx-CeO2/Activated Coke. Appl. Surf. Sci. 2015, 333, 59. (20) Chen, S. S.; Hsi, H. C.; Nian, S. H.; Chiu, C. H. Synthesis of N-Doped TiO2 Photocatalyst for LowConcentration Elemental Mercury Removal under Various Gas Conditions. Appl. Catal., B 2014, 160-161, 558. (21) Cho, J. H.; Eom, Y.; Jeon, S. H.; Lee, T. G. A Pilot-Scale TiO2 Photocatalytic System for Removing Gas-Phase Elemental Mercury at Hg-Emitting Facilities. J. Ind. Eng. Chem. 2013, 19, 144. (22) Yuan, Y.; Zhao, Y.; Li, H.; Li, Y.; Gao, X.; Zheng, C.; Zhang, J. Electrospun Metal Oxide-TiO2 Nanofibers for Elemental Mercury Removal from Flue Gas. J. Hazard. Mater. 2012, 227-228, 427. (23) Granite, E. J.; Pennline, H. W.; Hargis, R. A. Novel Sorbents for Mercury Removal from Flue Gas. Ind. Eng. Chem. Res. 2000, 39, 1020. (24) Presto, A. A.; Granite, E. J. Survey of Catalysts for Oxidation of Mercury in Flue Gas. Environ. Sci. Technol. 2006, 40, 5601. (25) Presto, A. A.; Granite, E. J.; Karash, A.; Hargis, R. A.; O'Dow, W. J.; Pennline, H. W. A Kinetic Approach to the Catalytic Oxidation of Mercury in Flue Gas. Energy Fuels 2006, 20, 1941. (26) Presto, A. A.; Granite, E. J. Noble Metal Catalysts for Mercury Oxidation in Utility Flue Gas. Platinum Metals Rev. 2008, 52, 144. (27) Li, M.; Liu, Z.; Hu, Y.; Wang, M.; Li, H. Effect of Doping Elements on Catalytic Performance of CeO2-ZrO2 Solid Solutions. J. Rare Earths 2008, 26, 357. (28) Bueno-Lopez, A.; Krishna, K.; Makkee, M.; Moulijin, J. Enhanced Soot Oxidation by Lattice Oxygen Via La3+-Doped CeO2. J. Catal. 2005, 230, 237. (29) Eom, Y.; Jeon, S. H.; Ngo, T. A.; Kim, J.; Lee, T. G. Heterogeneous Mercury Reaction on a Selective Catalytic Reduction (SCR) Catalyst. Catal. Lett. 2008, 121, 219.

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

(30) Li, H.; Wu, C. Y.; Li, Y.; Zhang, J. CeO2-TiO2 Catalysts for Catalytic Oxidation of Elemental Mercury in Low-Rank Coal Combustion Flue Gas. Environ. Sci. Technol. 2011, 45, 7394. (31) Li, Y.; Murphy, P. D.; Wu, C. Y.; Powers, K. W.; Bonzongo, J.-C. J. Development of Silica/Vanadia/Titania Catalysts for Removal of Elemental Mercury from Coal-Combustion Flue Gas. Environ. Sci. Technol. 2008, 42, 5304. (32) Gao, X.; Jiang, Y.; Zhong, Y.; Luo, Z.; Cen, K. The Activity and Characterization of CeO2-TiO2 Catalysts Prepared by the Sol-Gel Method for Selective Catalytic Reduction of NO With NH3. J. Hazard. Mater. 2010, 174, 734. (33) Liu, R.; Xu, W.; Tong, L.; Zhu, T. Role of NO in Hg0 Oxidation over a Commercial Selective Catalytic Reduction Catalyst V2O5-WO3/TiO2. J. Environ. Sci. 2015, 38, 126. (34) Huang, Y.; Gao, D.; Tong, Z.; Zhang, J.; Luo, H. Oxidation of NO over Cobalt Oxide Supported on Mesoporous Silica. J. Nat. Gas Chem. 2009, 18, 421. (35) Jin, R.; Liu, Y.; Wu, Z.; Wang, H.; Gu, T. Low-Temperature Selective Catalytic Reduction of NO With NH3 over Mn-Ce Oxides Supported on TiO2 and Al2O3: A Comparative Study. Chemosphere 2010, 78, 1160. (36) He, J.; Reddy, G. K.; Thiel, S. W.; Smirniotis, P. G.; Pinto, N. G. Simultaneous Removal of Elemental Mercury and NO from Flue Gas Using CeO2 Modified MnOx/TiO2 Materials. Energy Fuels 2013, 27, 4832. (37) Reddy, B. M.; Khan, A.; Yamada, Y.; Kobayashi, T.; Loridant, S.; Volta, J. C. Structural Characterization of CeO2−TiO2 and V2O5/CeO2−TiO2 Catalysts by Raman and XPS Techniques. J. Phys. Chem. B 2003, 107, 5162. (38) Liu, X.; Zhou, K.; Wang, L.; Wang, B.; Li, Y. Oxygen Vacancy Clusters Promoting Reducibility and Activity of Ceria Nanorods. J. Am. Chem. Soc. 2009, 131, 3140. (39) Yang, S.; Guo, Y.; Yan, N.; Wu, D.; He, H.; Qu, Z.; Jia, J. Elemental Mercury Capture from Flue Gas by Magnetic Mn–Fe Spinel: Effect of Chemical Heterogeneity. Ind. Eng. Chem. Res. 2011, 50, 9650. (40) Qiao, S.; Chen, J.; Li, J.; Qu, Z.; Liu, P.; Yan, N.; Jia, J. Adsorption and Catalytic Oxidation of Gaseous Elemental Mercury in Flue Gas over MnOx/Alumina. Ind. Eng. Chem. Res. 2009, 48, 3317. (41) Li, J.; Yan, N.; Qu, Z.; Qiao, S.; Yang, S.; Guo, Y.; Liu, P.; Jia, J. Catalytic Oxidation of Elemental Mercury over the Modified Catalyst Mn/Alpha-Al2O3 at Lower Temperatures. Environ. Sci. Technol. 2010, 44, 426. (42) Wang, P.; Su, S.; Xiang, J.; Cao, F.; Sun, L.; Hu, S.; Lei, S. Catalytic Oxidation of Hg0 by CuO– MnO2–Fe2O3/γ-Al2O3 Catalyst. Chem. Eng. J. 2013, 225, 68. (43) Niksa, S.; Helble, J. J.; Fujiwara, N. Kinetic Modeling of Homogeneous Mercury Oxidation: The Importance of NO and H2O in Predicting Oxidation in Coal-Derived Systems. Environ. Sci. Technol. 2001, 35, 3701. (44) Cao, Y.; Chen, B.; Wu, J.; Cui, H.; Smith, J.; Chen, C. K.; Chu, P.; Pan, W. P. Study of Mercury Oxidation by a Selective Catalytic Reduction Catalyst in a Pilot-Scale Slipstream Reactor at a Utility Boiler Burning Bituminous Coal. Energy Fuels 2007, 21, 145. (45) Du, W.; Yin, L.; Zhuo, Y.; Xu, Q.; Zhang, L.; Chen, C. Catalytic Oxidation and Adsorption of Elemental Mercury over CuCl2-Impregnated Sorbents. Ind. Eng. Chem. Res. 2014, 53, 582. (46) Kim, J. H.; Pudasainee, D.; Yoon, Y. S.; Son, S. U.; Seo, Y. C. Studies on Speciation Changes and Mass Distribution of Mercury in a Bituminous Coal-Fired Power Plant by Combining Field Data and Chemical Equilibrium Calculation. Ind. Eng. Chem. Res. 2010, 49, 5197. (47) Spörl, R.; Belo, L.; Shah, K.; Stanger, R.; Giniyatullin, R.; Maier, J.; Wall, T.; Scheffknecht, G. Mercury Emissions and Removal by Ash in Coal-Fired Oxy-Fuel Combustion. Energy Fuels 2014, 28, 123. (48) Wan, Q.; Duan, L.; He, K.; Li, J. Removal of Gaseous Elemental Mercury over a CeO2–WO3/TiO2 Nanocomposite in Simulated Coal-Fired Flue Gas. Chem. Eng. J. 2011, 170, 512. (49) Fan, X.; Li, C.; Zeng, G.; Zhang, X.; Tao, S.; Lu, P.; Tan, Y.; Luo, D. Hg0 Removal from

ACS Paragon Plus Environment

Page 22 of 25

Page 23 of 25

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

Simulated Flue Gas over CeO2/HZSM-5. Energy Fuels 2012, 26, 2082. (50) Tao, S.; Li, C.; Fan, X.; Zeng, G.; Lu, P.; Zhang, X.; Wen, Q.; Zhao, W.; Luo, D.; Fan, C. Activated Coke Impregnated with Cerium Chloride Used for Elemental Mercury Removal from Simulated Flue Gas. Chem. Eng. J. 2012, 210, 547. (51) Greiner, A.; Wendorff, J. H. Electrospinning: A Fascinating Method for the Preparation of Ultrathin Fibers. Angew. Chem., Int. Ed. 2007, 46, 5670. (52) Zhao, Y.; Han, Y.; Chen, C. Simultaneous Removal of SO2 and NO from Flue Gas Using Multicomposite Active Absorbent. Ind. Eng. Chem. Res. 2012, 51, 480. (53) Fang, P.; Cen, C. P.; Tang, Z. J. Experimental Study on the Oxidative Absorption of Hg0 by KMnO4 Solution. Chem. Eng. J. 2012, 198-199, 95. (54) Presto, A. A.; Granite, E. J.; Karash, A. Further Investigation of the Impact of Sulfur Oxides on Mercury Capture by Activated Carbon. Ind. Eng. Chem. Res. 2007, 46, 8273. (55) Presto, A. A.; Granite, E. J. Impact of Sulfur Oxides on Mercury Capture by Activated Carbon. Environ. Sci. Technol. 2007, 41, 6579. (56) Granite, E. J.; Pennline, H. W.; Hoffman, J. S. Effects of Photochemical Formation of Mercuric Oxide. Ind. Eng. Chem. Res. 1999, 38, 5034.

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure Captions

Figure 1. Schematic diagram of mercury oxidation fixed bed system. Figure 2. Interference of flue gas constituents on mercury measurement. Figure 3. Effect of individual flue gas constituents on Hg0 photocatalytic oxidation at 120 °C. Figure 4. Photocatalytic properties in the presence of SO2 (Inset was the S 2p spectra of spent catalyst). Figure 5. Desorption of Hg0 from catalyst by SO2. Figure 6. XPS spectra of S 2p for fresh and spent catalyst. Figure 7. FTIR spectra of the spent catalyst. Figure 8. XPS of O 1s and Ce 3d for (a) fresh catalyst, (b) spent catalyst under NO, (c) spent catalyst under NO/O2. Figure 9. Photocatalytic properties in the presence of HCl. Figure 10. Hg0 oxidation with 1200 ppm SO2 and various NO concentrations. Figure 11. Hg0 oxidation with 300 ppm NO and various SO2 concentrations.

ACS Paragon Plus Environment

Page 24 of 25

Page 25 of 25

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

For Table of Contents Only

ACS Paragon Plus Environment