Coupling of a Copper Dye with a Copper ... - ACS Publications

Jan 16, 2018 - Research Center for Renewable Energy & Enviromental Istituto Donegani ... A simple new heteroleptic copper dye, bearing one 2,9-dimesit...
0 downloads 0 Views 1MB Size
Article Cite This: ACS Appl. Energy Mater. 2018, 1, 751−756

www.acsaem.org

Coupling of a Copper Dye with a Copper Electrolyte: A Fascinating Springboard for Sustainable Dye-Sensitized Solar Cells Claudia Dragonetti,†,‡ Mirko Magni,†,‡ Alessia Colombo,*,†,‡ Fabio Melchiorre,§ Paolo Biagini,§ and Dominique Roberto†,‡ †

Dipartimento di Chimica, Università degli Studi di Milano and UdR INSTM di Milano, via Golgi 19, 20133 Milano, Italy Istituto di Scienze e Tecnologie Molecolari del CNR (CNR-ISTM), SmartMatLab Centre, via Golgi 19, 20133 Milano, Italy § Research Center for Renewable Energy & Enviromental Istituto Donegani, ENI S.p.A., via Fauser 4, I-28100 Novara, Italy Downloaded via KAOHSIUNG MEDICAL UNIV on July 30, 2018 at 15:43:16 (UTC). See https://pubs.acs.org/sharingguidelines for options on how to legitimately share published articles.



S Supporting Information *

ABSTRACT: A simple new heteroleptic copper dye, bearing one 2,9dimesityl-1,10-phenanthroline and a 6,6′-dimethyl-2,2′-bipyridine-4,4′-dibenzoic acid anchoring ligand, was used as photosensitizer in dye-sensitized solar cells (DSSCs). High power conversion efficiencies are reached not only with conventional I−/I3− electrolyte (40% relative conversion efficiency respect to N719) but, remarkably, also with a well-designed copper-based electrolyte. These proof-of-principle “full-copper” DSSCs open a fascinating route for environmentally friendly DSSCs.

KEYWORDS: copper, redox mediators, photosensitizer, DSSCs, energy

S

phenomenal amount of work has been dedicated to their use as sensitizers in DSSCs5−8,34−36 with the conventional I−/I3− redox couple as electrolyte. The homoleptic Cu(I) complexes were the first copper coordination compounds to be used in DSSCs starting from less than 0.1% efficiency37 to reach a maximum of 3.0%, for a copper complex bearing two 6,6′-dimethyl-2,2′-bipyridine-4,4′dibenzoic acid ligands, corresponding to a 33% relative efficiency (ηrel) with respect to an N719-sensitized control cell set at 100%.38,39 A big challenge was the use of heteroleptic complexes with two different diimine ligands, one with anchoring groups and the other functionalized with πdelocalized groups aimed to increase light harvesting.5−8 The actual 4.66% record efficiency, corresponding to a remarkable 63% ηrel, was obtained with a copper(I) complex having as anchoring ligand a 4,4′-dicarboxylic acid-6,6′dimesityl-2,2′bipyridine and, as ancillary ligand, a 4,4′-bis(N,N-diethylaminestyryl)-6,6′-dimethyl-2,2′-bipyridine working with the coadsorbent chenodeoxycholic acid.40 Recently, the investigation of heteroleptic copper(I) complexes has been also extended to the application in iodine-free solar cells in which I−/I3− has been replaced with a Co2+/3+-based electrolyte. In fact, a long-term incompatibility of copper complexes with the common mediator has been

ince the discovery of Grätzel-type DSSCs as a solution for harnessing the energy of the sun and converting it into electricity,1 there has been an exponential growth of work to improve the photoconversion efficiency (PCE), trying to optimize the sensitizer,2−8 and, in the past few years, the redox mediators.8−13 Except for porphyrin-sensitized14,15 and collaborative organic-sensitized16 solar cells filled with Co2+/3+-based electrolytes that reach 13−14% efficiencies, the best PCEs (ca. 12%) have so far been achieved with bipyridyl complexes of ruthenium, such as benchmark cis-di(thiocyanato)bis(2,2′-bipyridine-4,4′dicarboxylate)Ru(II) (N3) and its doubly deprotonated analogue (N719),17 and related Ru(II) complexes,18−20 with the iodide/triiodide couple (I−/I3−) as electrolyte. The role of the carboxylate groups is to anchor the dye to the titania surface. The photoexcitation of the dye involves the transfer of an electron from the Ru center to the π* orbital of the carboxylated bipyridine, allowing electron injection into the TiO2 conduction band. A negative aspect of these Ru(II) complexes is the presence of the thiocyanate ligand which can be easily replaced, giving less efficient species.21 For this reason, a lot of efforts have been devoted to the preparation of thiocyanate-free ruthenium sensitizers.22−28 However, ruthenium is one of the rarest and most expensive metals, and this is a drawback in the design of low-cost DSSCs. Photophysical, economic, and environmental considerations make copper(I) coordination compounds interesting alternatives to ruthenium complexes.5,7,29−33 As a matter of fact, in the past few years, a © 2018 American Chemical Society

Received: November 29, 2017 Accepted: January 16, 2018 Published: January 16, 2018 751

DOI: 10.1021/acsaem.7b00196 ACS Appl. Energy Mater. 2018, 1, 751−756

Article

ACS Applied Energy Materials demonstrated, due to the low solubility of CuI.41,42 By using [Co(bpy)3]2+/3+ (bpy = 2,2′-bipyridine) as redox couple and a heteroleptic copper(I) complex, having ((6,6′-dimethyl-[2,2′bipyridine]-4,4′-diyl)bis(4,1-phenylene)bis(phosphonic acid) as anchoring ligand and a 2-(diphenylaminophenyl)-1Hphenanthro[9,10-d]imidazole derivative ancillary ligand, as dye, Constable and co-workers prepared a fully masked DSSC with a 1.73% efficiency (25% ηrel) comparable to that obtained with the reference I−/I3 − electrolyte.42 This combination of copper(I)-based dyes and [Co(bpy)3]2+/3+ electron shuttles was a critical step toward the development of stable iodide-free copper(I) solar cells.43 It just appeared that, in combination with both ruthenium(II) dyes and organic sensitizers, Cu+/2+ mediators outperform not only iodine-based electrolytes44−47 but also a common Cobased redox couple.48,49 Fast dye regeneration and tunability of both redox potential and electron transfer rate make Cu mediators prone to solve the thermodynamic and kinetic dichotomies of the device operation.50 These observations, and the fact that well-designed Cu complexes may act both as dyes and mediators, prompted us to couple a simple heteroleptic copper(I) dye with homoleptic copper-based redox couples as electron shuttles in order to open the way toward environmental friendly DSSCs. Thus, we prepared with the HETPHEN synthetic method51 the new copper(I) dye D (Chart 1) bearing one 2,9-dimesityl-

performance of D in DSSCs was studied in the presence of three different electrolytes, namely, the common I−/I3− electrolyte and two couples of copper redox shuttles (E1/E2 and E3/E4, Chart 1). The Cu complexes with the 2,9-dimethyl1,10-phenanthroline ligand (E1/E2) were prepared as reported45,47 whereas E3 and E4 with the 2-n-butyl-1,10phenanthroline were prepared from CuCl and CuSO4·5H2O, respectively (see Supporting Information).47,52 The visible region absorption spectrum (SI, Figure S1) of D in CH2Cl2 shows a broad band centered at 478 nm (Table 1), Table 1. Key Optical Absorption and Cyclovoltammetric Data for the Investigated Complexes λmax/nm (103 ε /M−1 cm−1) D E1 E2 E3 E4

478 455 741 452 756

c

(7.6) (8.0)d (0.23)d (6.2)d (0.096)d

E1/2,Ox./V vs Fc+|Fca e

0.39 0.30f 0.04f 0.11f 0.11f

HOMO/eVb −5.19 −5.10 −4.84 −4.91 −4.91

With [NBu4][PF6] 0.1 M, on GC electrode at 0.2 V s−1. bHOMO = −e[E1/2,Ox. + 4.8]. e = unitary charge; 4.8 = potential of Fc+|Fc couple versus vacuum.54 cIn CH2Cl2. dIn CH3CN. eIn CH3CN/CH2Cl2 25/1, E1/2 Fc+|Fc = 0.40 V vs SCE. fIn CH3CN, E1/2 Fc+|Fc = 0.39 V vs SCE. a

due to a metal-to-ligand charge transfer transition (MLCT), along with a shoulder at higher wavelengths in agreement with the fingerprint of other copper(I) complexes with 2,9disubstituted phenanthrolines.29,53 Excitation at 478 nm of D in air-equilibrated CH2Cl2 generates an emission band of low intensity at 559 nm (Figure S2). The two Cu(I) mediators (E1 and E3) are characterized by an MLCT around 450 nm, with molar extinction coefficients comparable to those of D, that could hamper light harvesting by D-sensitized TiO2 photoanode, negatively affecting the overall conversion efficiencies. The related oxidized forms E2 and E4 exhibit a very low broad band at 750 nm, attributable to d−d transitions and negligible with respect to the 100-fold more intense MLCT of D (Table 1). A cyclic voltammetry study (CV) on glassy carbon electrode (GC) was performed to clarify the electrochemical behavior of both the D dye and the E1/E2 and E3/E4 redox couples. Key energetic levels were also determined to establish the suitability of D as sensitizer for TiO2 photoanodes and to verify the level matching between dye and electron mediators, mandatory for DSSC to work. The electrochemical response of D was compared with that of the related free ligands, working in N,N-dimethylformamide, DMF (Figure 1). Both the dicarboxyl bipyridine anchoring ligand, bpy-L, and the sterically hindered phe-L showed CV characteristics in good agreement with similar compounds,27,50 with bpy-L being more easily reduced thanks to the presence of electron withdrawing COOH groups. D shows two subsequent chemically and electrochemically quasireversible cathodic peaks due to electron transfers centered on the ligands, probably on the electron poorer bpy-L. On the anodic side, the noncanonical signal with peak potential at 0.37 V versus Fc+|Fc can be attributed to the Cu(I)/Cu(II) electron transfer, whose chemical reversibility (backward peak at about −0.26 V vs Fc+| Fc) is hampered by interactions with coordinating solvent. In fact, when less donating solvents (CH3CN > CH2Cl2) were employed, the same Cu-centered process progressively assumes

Chart 1. Chemical Structures of the Investigated Dye (D) and of the Two Couples of Copper-Based Redox Mediators (E1/E2 and E3/E4)

1,10-phenanthroline (phe-L), where the mesityl groups provide the necessary steric hindrance to avoid the formation of homoleptic complexes and prevent geometric changes, and a 6,6′-dimethyl-2,2′-bipyridine-4,4′-dibenzoic acid (bpy-L), chosen as anchoring ligand because the related homoleptic copper complex had a high efficiency as photosensitizer.39 The 752

DOI: 10.1021/acsaem.7b00196 ACS Appl. Energy Mater. 2018, 1, 751−756

Article

ACS Applied Energy Materials

two species. The level energy matching between D and Cubased redox mediators is promising, being the driving force for dye regeneration 0.09 and 0.28 eV for E1/E2 and E3/E4, respectively (Table 1). Interestingly, the E3/E4 couple offers a well-balanced oxidation half-wave potential, E1/2,Ox., that could thermodynamically ensure an efficient dye recovery without overwhelming the output photovoltage of the device. Dye-sensitized solar cells were fabricated using FTO glass coated TiO2 sensitized with D as photoanode, a platinized FTO counter electrode, and an electrolyte solution containing the conventional I−/I3− redox couple, the known E1/E2 and the novel E3/E4 couple (Supporting Information). Results of the investigated thin film DSSCs are presented in Table 2 together with those obtained with the Ru(II) benchmark N719 and the previously reported related homoleptic copper(I) dye bearing two 6,6′-dimethyl-2,2′-bipyridine-4,4′-dibenzoic acid ligands, Cu(bpy-L)2+.39 In addition to the absolute photoconversion efficiency (η), Table 2 reports the efficiency relative to a cell based on N719 dye and the standard I−/I3− electrolyte set at 100% (ηrel). It appeared that the novel heteroleptic copper complex D bearing one 2,9-dimesityl-1,10-phenanthroline and a 6,6′dimethyl-2,2′-bipyridine-4,4′-dibenzoic acid anchoring ligand (bpy-L) acts as a more efficient dye than the related homoleptic complex Cu(bpy-L)2+, due to a higher photocurrent density (jsc; Table 2) as expected for a better directionality for electron injection in the TiO2 conduction band.5−8 It is worth pointing out that D is much better performing that the related heteroleptic complex bearing the same 2,9-dimesityl-1,10phenanthroline but 2,2′-biquinoline-4,4′-dicarboxylic acid as anchoring ligand (η = 0.49%; ηrel = 7.5%) and characterized by lower molar extinction coefficients,58 confirming the particular goodness of 6,6′-dimethyl-2,2′-bipyridine-4,4′-dibenzoic acid to anchor the dye on the titania surface.39 With the simple heteroleptic dye D, we wanted to check the possibility to fabricate a “full-copper” DSSC as a sustainable route for environmentally friendly DSSCs. Remarkably, substitution of the common I−/I3− redox couple by the wellknown E1/E2 couple leads to a fair efficiency (Table 2) that is increased by a factor of 1.5 by using the novel E3/E4 couple (η= 2.0 %; ηrel = 22%) due to a much better jSC and FF. The lower short-circuit photocurrent observed with the E1/E2 couple can be attributed to a more competitive light harvesting with D, as indicated by a higher molar extinction coefficient of the absorption band around 450 nm (Table 1), in agreement with a lower IPCE curve at 475 nm (Figure 2).

Figure 1. CV patterns of D and related free ligands. Sample concentration 5.5 × 10−4 M in DMF with [NBu4][PF6] 0.1 M, GC electrode, 0.2 V s−1 scan rate potential.

a higher degree of chemical and electrochemical reversibility (Figure S3) and shifts at more positive potentials.50 Estimation of the energy level of the highest occupied molecular orbital (HOMO) and of the excited state (U(D*| D+)) of the dye is important to judge its applicability in DSSCs. The HOMO of D was evaluated in the same solvent used in the photoelectrochemical devices (CH3CN, Table 1) while its excited state energy level was estimated according to eq 155 in CH2Cl2, due to the smaller propensity of the solvent to quench emission signals, using E1/2,Ox. = 0.47 V versus Fc+|Fc (in CH2Cl2 with 0.1 M [NBu4][PF6]) and U0−0 = 2.38 eV [the 0− 0 transition energy estimated as U0−0 = hc/λcross by the wavelength at the cross point, λcross (Figure S2), between normalized absorption and emission spectrum in CH2Cl2].56 ⎤ ⎡ ⎛U ⎞ U (D*|D+) = −e⎢ −⎜ 0 − 0 − E1/2,Ox.⎟ + 4.8⎥ ⎠ ⎦ ⎣ ⎝ e

(1)

According to this equation, the estimated U(D*|D ) is −2.89 eV, a value that should guarantee sufficient driving force to efficiently inject electrons into the underlying TiO2 conduction band, placed at ca. −3.5 eV (calculated using E1/2 Fc+|Fc = 0.63 V vs NHE).57 As mentioned for D, and reported for related complexes,46,47,49,50 the chemically reversible and electrochemically quasireversible electron transfer for E3 and E4 can be attributed to a metal-centered process which brings a quite limited rearrangement of the coordination sphere around the Cu atom (Figure S4). The quite perfectly superimposable CV patterns of E3 and E4 suggest a mutual interconversion of the +

Table 2. Photoelectrochemical Performance of DSSCs dye d

N719 Cu(bpyL)2+d D D D D

electrolyte [oxidizer, M]a −

I /I3−e,f [0.04] I−/I3−e,f [0.04] I−/I3−e,f [0.04] I−/I3−e,g [0.017] h E1/E2 [0.017] E3/E4h [0.017]

jSC, mA cm−2

VOC, V

FF

η%b

ηrel%c

15.4 7.3 9.0 8.2 4.7 6.3

0.80 0.59 0.61 0.67 0.75 0.61

71 69 63 65 36 53

8.9 3.0 3.5 3.6 1.3 2.0

100% 33% 39% 40% 15% 22%

a

Concentration of the oxidizer in M. bThere is a decrease of the efficiencies in the range 25−30% by working in the presence of a 16 mm2 black mask. cRelative efficiency respect to a N719-sensitized control cell set at 100%. dRef 39. e0.28 M tert-butylpyridine in 15/85 (v/v) mixture of valeronitrile/acetonitrile. f0.65 M N-methyl-N-butylimidazolium iodide, 0.025 M LiI, 0.04 M iodine; in the case of N719, 0.05 M guanidinium thiocyanate is present. g0.26 M N-methyl-N-butylimidazolium iodide, 0.01 M LiI, 0.017 M iodine. h0.17 M Cu(I): 0.017 M Cu(II) + 0.1 M LiTFSI in CH3CN. 753

DOI: 10.1021/acsaem.7b00196 ACS Appl. Energy Mater. 2018, 1, 751−756

Article

ACS Applied Energy Materials



Synthesis and characterization of dye and electrolytes, electrochemical measurements, and fabrication of dyesensitized solar cells (PDF)

AUTHOR INFORMATION

Corresponding Author

*E-mail: [email protected]. ORCID

Mirko Magni: 0000-0001-9776-2973 Alessia Colombo: 0000-0001-8004-3200 Dominique Roberto: 0000-0001-9659-4760

Figure 2. IPCE for DSSCs sensitized with D and I−/I3− 0.04 M oxidizer (a), I−/I3− 0.017 M oxidixer (b), E1/E2 (c), and E3/E4 (d) as electrolyte.

Notes

The authors declare no competing financial interest.



In addition to their absorption in the visible region, a limitation of these Cu complex mediators could be their low solubility which hampers the use of an electrolyte solution as concentrated as the conventional I−/I3− solution. In fact, in the case of E1/E2 and E3/E4 redox couples, we succeeded in preparing acetonitrile solutions to 0.017 M for the corresponding Cu2+ complex, while in the standard I−/I3− couple the oxidized form is 0.04 M. Therefore, in order to better compare the performances of Cu+/Cu2+ and I−/I3− electrolytes, we fabricated cells with a 2.4-fold more diluted I−/I3− concentration with respect to the traditional one. Surprisingly, a similar efficiency (η = 3.6%; ηrel = 40%) was obtained upon dilution, but it was reached with a significant decrease of the jsc which compensates for a considerable increase of the Voc (Table 2). This unexpected observation suggests that in Cu-based electrolytes an optimization of the concentration of the components should be performed to understand the entire potentiality of the related DSSCs. Further work is in progress in our laboratory on this fascinating topic. Taking into account that the conventional redox couple I−/ − I3 has many problems, such as complicated two-electron redox chemistry and corrosiveness, and that Co2+/3+ complexes are outer-sphere one-electron redox systems with tunable redox potentials, bringing some issues associated with their slow mass transport and large internal reorganization energy between the high-spin d7 and low-spin d6 states which costs driving force for dye regeneration, clearly well-designed Cu+/2+ complexes are promising alternative electron shuttles.48,49 Wonderfully, the present work shows for the first time that they can be combined to copper dyes to give performing solar cells. In conclusion, not only does this work confirm the good performance of 6,6′-dimethyl-2,2′-bipyridine-4,4′-dibenzoic acid to anchor Cu dyes on the titania surface, but also, most importantly, it shows that it is possible to fabricate environmentally friendly “full-copper” DSSCs. With the efficiency of DSSCs based on Cu dyes or Cu mediators increased by a factor of ca. 50 and 100 from their first use, the already good efficiencies of the newborn f ull-copper DSSCs are expected to rapidly increase. We are currently working to improve the solar light harvesting of the Cu dyes, with well-designed functional groups, and to increase the Voc, by looking for an optimal concentration of the Cu-based electrolytes in the presence of additives such as tert-butylpyridine, as commonly employed with a conventional I−/I3− electrolyte.



ACKNOWLEDGMENTS A.C. thanks Università degli Studi di Milano (Piano Sostegno alla Ricerca 2015−17-LINEA 2 Azione AGiovani Ricercatori) for financial support. We thank Dr. Daniele Marinotto (CNR) and Dr. Stefano Chiaberge (ENI), for emission and mass spectra, and both Regione Lombardia and Fondazione Cariplo for the use of instrumentation purchased through the SmartMatLab Centre project (2014). The “Ministero degli Affari Esteri e della Cooperazione Internazionale” is also acknowledged (bilateral project Italy-India, Prot. nr. MAE0104617) for financial support.



REFERENCES

(1) O’Regan, B.; Grätzel, M. A Low-cost, High-efficiency Solar Cell Based on Dye-sensitized Colloidal TiO2 Films. Nature 1991, 353, 737−740. (2) Grätzel, M. Recent Advances in Sensitized Mesoscopic Solar Cells. Acc. Chem. Res. 2009, 42, 1788−1798. (3) Vougioukalakis, G. C.; Philippopoulos, A. I.; Stergiopoulos, T.; Falaras, P. Contributions to the Development of Ruthenium-based Sensitizers for Dye-Sensitized Solar Cells. Coord. Chem. Rev. 2011, 255, 2602−2621. (4) Li, L.-L.; Diau, E. W.-G. Porphyrin-Sensitized Solar Cells. Chem. Soc. Rev. 2013, 42, 291−304. (5) Housecroft, C. E.; Constable, E. C. The Emergence of Copper(I)-based Dye Sensitized Solar Cells. Chem. Soc. Rev. 2015, 44, 8386−8398. (6) Zhou, N.; Prabakaran, K.; Lee, B.; Chang, S. H.; Harutyunyan, B.; Guo, P.; Butler, M. R.; Timalsina, A.; Bedzyk, M. J.; Ratner, M. A.; Vegiraju, S.; Yau, S.; Wu, C.-G.; Chang, R. P. H.; Facchetti, A.; Chen, M.-C.; Marks, T. J. Metal-Free Tetrathienoacene Sensitizers for HighPerformance Dye-Sensitized Solar Cells. J. Am. Chem. Soc. 2015, 137, 4414−4423. (7) Sandroni, M.; Pellegrin, Y.; Odobel, F. Heteroleptic Bis-diimine Copper(I) Complexes for Applications in Solar Energy Conversion. C. R. Chim. 2016, 19, 79−93. (8) Magni, M.; Biagini, P.; Colombo, A.; Dragonetti, C.; Roberto, D.; Valore, A. Versatile Copper Complexes as a Convenient Springboard for both Dyes and Redox Mediators in Dye Sensitized Solar Cells. Coord. Chem. Rev. 2016, 322, 69−93. (9) Hamann, T. W.; Jensen, R. A.; Martinson, A. B. F.; Van Ryswyk, H.; Hupp, J. T. Advancing Beyond Current Generation Dye-Sensitized Solar Cells. Energy Environ. Sci. 2008, 1, 66−78. (10) Hamann, T. W. The End of Iodide? Cobalt Complex Redox Shuttles in DSSCs. Dalton Trans. 2012, 41, 3111−3115. (11) Wang, M.; Graetzel, C.; Zakeeruddin, S. M.; Grätzel, M. Recent Developments in Redox Electrolytes for Dye-Sensitized Solar Cells. Energy Environ. Sci. 2012, 5, 9394−9405. (12) Wu, J.; Lan, Z.; Lin, J.; Huang, M.; Huang, Y.; Fan, L.; Luo, G. Electrolytes in Dye-Sensitized Solar Cells. Chem. Rev. 2015, 115, 2136−2173.

ASSOCIATED CONTENT

S Supporting Information *

The Supporting Information is available free of charge on the ACS Publications website at DOI: 10.1021/acsaem.7b00196. 754

DOI: 10.1021/acsaem.7b00196 ACS Appl. Energy Mater. 2018, 1, 751−756

Article

ACS Applied Energy Materials (13) Pashaei, B.; Shahroosvand, H.; Abbasi, P. Transition Metal Complex Redox Shuttles for Dye-Sensitized Solar Cells. RSC Adv. 2015, 5, 94814−94848. (14) Yella, A.; Lee, H.-W.; Tsao, H. N.; Yi, C.; Chandiran, A. K.; Nazeeruddin, Md. K.; Diau, E. W.-G.; Yeh, C.-Y.; Zakeeruddin, S. M.; Graetzel, M. Porphyrin-Sensitized Solar Cells with Cobalt (II/III)− Based Redox Electrolyte Exceed 12% Efficiency. Science 2011, 334, 629−634. (15) Mathew, S.; Yella, A.; Gao, P.; Humphry-Baker, R.; Curchod, B. F. E.; Ashari-Astani, N.; Tavernelli, I.; Rothlisberger, U.; Nazeeruddin, M. K.; Grätzel, M. Dye-Sensitized Solar Cells with 13% Efficiency Achieved Through the Molecular Engineering of Porphyrin Sensitizers. Nat. Chem. 2014, 6, 242−247. (16) Kakiage, K.; Aoyama, Y.; Yano, T.; Oya, K.; Fujisawa, J.; Hanaya, M. Highly-Efficient Dye-Sensitized Solar Cells with Collaborative Sensitization by Silyl-anchor and Carboxy-anchor Dyes. Chem. Commun. 2015, 51, 15894−15897. (17) Nazeeruddin, M. K.; Zakeeruddin, S. M.; Humphry-Baker, R.; Jirousek, M.; Liska, P.; Vlachopoulos, N.; Shklover, V.; Fischer, C.-H.; Graetzel, M. Acid−Base Equilibria of (2,2′-Bipyridyl-4,4′-dicarboxylic acid)ruthenium(II) Complexes and the Effect of Protonation on Charge-Transfer Sensitization of Nanocrystalline Titania. Inorg. Chem. 1999, 38, 6298−6305. (18) Chen, C.-Y.; Wang, M.; Li, J.-Y.; Pootrakulchote, N.; Alibabaei, L.; Ngoc-le, C.; Decoppet, J.-D.; Tsai, H.-H.; Graetzel, C.; Wu, C.-G.; Zakeeruddin, S. M.; Gratzel, M. Highly Efficient Light-Harvesting Ruthenium Sensitizer for Thin-Film Dye-Sensitized Solar Cells. ACS Nano 2009, 3, 3103−3109. (19) Yu, Q.; Wang, Y.; Yi, Z.; Zu, N.; Zhang, J.; Zhang, M.; Wang, P. High-Efficiency Dye-Sensitized Solar Cells: The Influence of Lithium Ions on Exciton Dissociation, Charge Recombination, and Surface States. ACS Nano 2010, 4, 6032−6038. (20) Ozawa, H.; Okuyama, Y.; Arakawa, H. Dependence of the Efficiency Improvement of Black-Dye-Based Dye-Sensitized Solar Cells on Alkyl Chain Length of Quaternary Ammonium Cations in Electrolyte Solutions. ChemPhysChem 2014, 15, 1201−1206. (21) Colombo, A.; Dragonetti, C.; Valore, A.; Coluccini, C.; Manfredi, N.; Abbotto, A. Thiocyanate-free Ruthenium(II) 2,2′Bipyridyl Complexes for Dye-Sensitized Solar Cells. Polyhedron 2014, 82, 50−56 and references therein.. (22) Bomben, P. G.; Koivisto, B. D.; Berlinguette, C. P. Cyclometalated Ru Complexes of Type [RuII(N∧N)2(C∧N)]z: Physicochemical Response to Substituents Installed on the Anionic Ligand. Inorg. Chem. 2010, 49, 4960−4971. (23) Abbotto, A.; Coluccini, C.; Dell’Orto, E.; Manfredi, N.; Trifiletti, V.; Salamone, M. M.; Ruffo, R.; Acciarri, M.; Colombo, A.; Dragonetti, C.; Ordanini, S.; Roberto, D.; Valore, A. Thiocyanate-free Cyclometalated Ruthenium Sensitizers for Solar Cells Based on Heteroaromatic-substituted 2-arylpyridines. Dalton Trans. 2012, 41, 11731− 11738. (24) Dragonetti, C.; Valore, A.; Colombo, A.; Roberto, D.; Trifiletti, V.; Manfredi, N.; Salamone, M. M.; Ruffo, R.; Abbotto, A. A New Thiocyanate-free Cyclometallated Ruthenium Complex for DyeSensitized Solar Cells: Beneficial Effects of Substitution on the Cyclometallated Ligand. J. Organomet. Chem. 2012, 714, 88−93. (25) Robson, K. C. D.; Koivisto, B. D.; Berlinguette, C. P. Derivatization of Bichromic Cyclometalated Ru(II) Complexes with Hydrophobic Substituents. Inorg. Chem. 2012, 51, 1501−1507. (26) Dragonetti, C.; Valore, A.; Colombo, A.; Magni, M.; Mussini, P.; Roberto, D.; Ugo, R.; Valsecchi, A.; Trifiletti, V.; Manfredi, N.; Abbotto, A. Ruthenium Oxyquinolate Complexes for Dye-Sensitized Solar Cell. Inorg. Chim. Acta 2013, 405, 98−104. (27) Dragonetti, C.; Colombo, A.; Magni, M.; Mussini, P.; Nisic, F.; Roberto, D.; Ugo, R.; Valore, A.; Valsecchi, A.; Salvatori, P.; Lobello, M. G.; De Angelis, F. Thiocyanate-free Ruthenium(II) Sensitizer with a Pyrid-2-yltetrazolate Ligand for Dye-Sensitized Solar Cells. Inorg. Chem. 2013, 52, 10723−10725. (28) Colombo, A.; Dragonetti, C.; Magni, M.; Meroni, D.; Ugo, R.; Marotta, G.; Grazia Lobello, M.; Salvatori, P.; De Angelis, F. New

Thiocyanate-Free Ruthenium(II) Sensitizers with Different Pyrid-2-yl Tetrazolate Ligands for Dye-Sensitized Solar Cells. Dalton Trans. 2015, 44, 11788−11796. (29) Armaroli, N. Photoactive Mono- and Polynuclear Cu(I)− phenanthrolines. A Viable Alternative to Ru(II)−polypyridines? Chem. Soc. Rev. 2001, 30, 113−124. (30) Armaroli, N.; Accorsi, G.; Cardinali, F.; Listorti, A. Photochemistry and Photophysics of Coordination Compounds: Copper. Top. Curr. Chem. 2007, 280, 69−115. (31) Robertson, N. CuI versus RuII: Dye-Sensitized Solar Cells and Beyond. ChemSusChem 2008, 1, 977−979. (32) Bozic-Weber, B.; Constable, E. C.; Housecroft, C. E. Light Harvesting with Earth Abundant d-block Metals: Development of Sensitizers in Dye-Sensitized Solar Cells (DSCs). Coord. Chem. Rev. 2013, 257, 3089−3106. (33) Mara, M. W.; Fransted, K. A.; Chen, L. X. Interplays of Excited State Structures and Dynamics in Copper(I) Diimine Complexes: Implications and Perspectives. Coord. Chem. Rev. 2015, 282, 2−18. (34) Buttner, A.; Brauchli, S. Y.; Vogt, R.; Constable, E. C.; Housecroft, C. E. Combining Phosphonic Acid-functionalized Anchoring Ligands with Asymmetric Ancillary Ligands in Bis(diimine)copper(I) Dyes for Dye-Sensitized Solar Cells. RSC Adv. 2016, 6, 5205−5213. (35) Willgert, M.; Boujemaoui, A.; Malmstrom, E.; Constable, E. C.; Housecroft, C. E. Copper-based Dye-Sensitized Solar Cells with Quasi-Solid Nano Cellulose Composite Electrolytes. RSC Adv. 2016, 6, 56571−56579. (36) Furer, S. O.; Luu, L. Y. N.; Bozic-Weber, B.; Constable, E. C.; Housecroft, C. E. Improving Performance of Copper(I)-based Dye Sensitized Solar Cells Through I3−/I− Electrolyte Manipulation. Dyes Pigm. 2016, 132, 72−78. (37) Alonso-Vante, N.; Nierengarten, J.-F.; Sauvage, J.-P. Spectral Sensitization of Large-band-gap Semiconductors (thin films and ceramics) by a Carboxylated bis(1,10-phenanthroline)copper(I) Complex. J. Chem. Soc., Dalton Trans. 1994, 11, 1649−1654. (38) To compare the photoconversion efficiencies of DSSCs obtained in various laboratories, it may be convenient to report not only the absolute efficiency but also that relative to a cell based on N719 dye and I−/I3− electrolyte set at 100% measured in the same laboratory. (39) Colombo, A.; Dragonetti, C.; Roberto, D.; Valore, A.; Biagini, P.; Melchiorre, F. A simple Copper(I) Complex and its Application in Efficient Dye Sensitized Solar Cells. Inorg. Chim. Acta 2013, 407, 204− 209. (40) Sandroni, M.; Favereau, L.; Planchat, A.; Akdas-Kilig, H.; Szuwarski, N.; Pellegrin, Y.; Blart, E.; Le Bozec, H.; Boujtita, M.; Odobel, F. Heteroleptic Copper(I)−polypyridine Complexes as Efficient Sensitizers for Dye Sensitized Solar Cells. J. Mater. Chem. A 2014, 2, 9944−9947. (41) Ashbrook, L. N.; Elliott, C. M. Dye-Sensitized Solar Cell Studies of a Donor-Appended Bis(2,9-dimethyl-1,10-phenanthroline) Cu(I) Dye Paired with a Cobalt-Based Mediator. J. Phys. Chem. C 2013, 117, 3853−3864. (42) Bozic-Weber, B.; Constable, E. C.; Fuerer, S. O.; Housecroft, C. E.; Troxler, L. J.; Zampese, J. A. Copper(I) Dye-Sensitized Solar Cells with [Co(bpy)3]2+/3+ Electrolyte. Chem. Commun. 2013, 49, 7222− 7224. (43) Furer, S. O.; Bozic-Weber, B.; Schefer, T.; Wobill, C.; Constable, E. C.; Housecroft, C. E.; Willgert, M. Understanding why Replacing I3−/I− by Cobalt(II)/(III) Electrolytes in Bis(diimine)copper(I)-based Dye-Sensitized Solar Cells Improves Performance. J. Mater. Chem. A 2016, 4, 12995−13004. (44) Hattori, S.; Wada, Y.; Yanagida, S.; Fukuzumi, S. Blue Copper Model Complexes with Distorted Tetragonal Geometry Acting as Effective Electron-transfer Mediators in Dye-Sensitized Solar Cells. J. Am. Chem. Soc. 2005, 127, 9648−9654. (45) Bai, Y.; Yu, Q.; Cai, N.; Wang, Y.; Zhang, M.; Wang, P. HighEfficiency Organic Dye-Sensitized Mesoscopic Solar Cells with a Copper Redox Shuttle. Chem. Commun. 2011, 47, 4376−4378. 755

DOI: 10.1021/acsaem.7b00196 ACS Appl. Energy Mater. 2018, 1, 751−756

Article

ACS Applied Energy Materials (46) Colombo, A.; Dragonetti, C.; Magni, M.; Roberto, D.; Demartin, F.; Caramori, S.; Bignozzi, C. A. Efficient Copper Mediators Based on Bulky Asymmetric Phenanthrolines for DSSCs. ACS Appl. Mater. Interfaces 2014, 6, 13945−13955. (47) Magni, M.; Giannuzzi, R.; Colombo, A.; Cipolla, M. P.; Dragonetti, C.; Caramori, S.; Carli, S.; Grisorio, R.; Suranna, G. P.; Bignozzi, C. A.; Roberto, D.; Manca, M. Tetracoordinated Bisphenanthroline Copper-Complex Couple as Efficient Redox Mediators for Dye Solar Cells. Inorg. Chem. 2016, 55, 5245−5253. (48) Freitag, M.; Giordano, F.; Yang, W.; Pazoki, M.; Hao, Y.; Zietz, B.; Grätzel, M.; Hagfeldt, A.; Boschloo, G. Copper Phenanthroline as a Fast and High-Performance Redox Mediator for Dye-Sensitized Solar Cells. J. Phys. Chem. C 2016, 120, 9595−9603. (49) Colombo, A.; Di Carlo, G.; Dragonetti, C.; Magni, M.; Orbelli Biroli, A.; Pizzotti, M.; Roberto, D.; Tessore, F.; Benazzi, E.; Bignozzi, C. A.; Casarin, L.; Caramori, S. Coupling of Zinc Porphyrin Dyes and Copper Electrolytes: A Springboard for Novel Sustainable DyeSensitized Solar Cells. Inorg. Chem. 2017, 56, 14189−14197. (50) Magni, M.; Colombo, A.; Dragonetti, C.; Mussini, P. Steric vs Electronic Effects and Solvent Coordination in the Electrochemistry of Phenanthroline-based Copper Complexes. Electrochim. Acta 2014, 141, 324−330. (51) Schmittel, M.; Ganz, A. Stable Mixed Phenanthroline Copper(I) Complexes. Key Buildingblocks for Supramolecular Coordination Chemistry. Chem. Commun. 1997, 999−1000. (52) Latham, K.; White, K. F.; Szpakolski, K. B.; Rix, C. J.; White, J. M. Synthesis, Crystal Structure and Luminescent Behaviour of Coordination Complexes of Copper with bi- and tridentate Amines and Phosphonic Acids. Inorg. Chim. Acta 2009, 362, 1872−1886. (53) Scaltrito, D. V.; Thompson, D. W.; O’Callaghan, J. A.; Meyer, G. J. MLCT Excited States of Cuprous Bis-phenanthroline Coordination Compounds. Coord. Chem. Rev. 2000, 208, 243−266. (54) Trasatti, S. The Absolute Electrode Potential: an Explanatory Note. Pure Appl. Chem. 1986, 58, 955−966. (55) Parson, W. W. Modern Optical Spectroscopy, 2nd ed.; Springer, 2015. (56) Juris, A.; Balzani, V.; Barigelletti, F.; Campagna, S.; Belser, P.; von Zelewsky, A. Ru(II) Polypyridine Complexes: Photophysics, Photochemistry, Eletrochemistry, and Chemiluminescence. Coord. Chem. Rev. 1988, 84, 85−277. (57) Listorti, A.; O’Regan, B.; Durrant, J. R. Electron Transfer Dynamics in Dye-Sensitized Solar Cells. Chem. Mater. 2011, 23, 3381−3399. (58) Sandroni, M.; Kayanuma, M.; Planchat, A.; Szuwarski, N.; Blart, E.; Pellegrin, Y.; Daniel, C.; Boujtita, M.; Odobel, F. First Application of the HETPHEN Concept to New Heteroleptic Bis(diimine) Copper(I) Complexes as Sensitizers in Dye Sensitized Solar Cells. Dalton Trans. 2013, 42, 10818−10827.

756

DOI: 10.1021/acsaem.7b00196 ACS Appl. Energy Mater. 2018, 1, 751−756