Crossing the Border between Laboratory and Field: Bacterial Quorum

Jan 15, 2016 - Quorum quenching (QQ) has recently been acknowledged to be a sustainable antifouling strategy and has been investigated widely using la...
0 downloads 15 Views 973KB Size
Subscriber access provided by UNIV OF CALIFORNIA SAN DIEGO LIBRARIES

Article

Crossing the Border between Laboratory and Field: Bacterial Quorum Quenching for Anti-Biofouling Strategy in an MBR Seonki Lee, Seung-Kook Park, Hyeokpil Kwon, Sang Hyun Lee, Kibaek Lee, Chang Hyun Nam, Sung Jun Jo, Hyun-Suk Oh, Pyung-Kyu Park, Kwang-Ho Choo, Chung-Hak Lee, and Taewoo Yi Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.5b04795 • Publication Date (Web): 15 Jan 2016 Downloaded from http://pubs.acs.org on January 19, 2016

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 22

Environmental Science & Technology

1

Crossing the Border between Laboratory and Field:

2

Bacterial Quorum Quenching for Anti-Biofouling

3

Strategy in an MBR

4 5

Seonki Lee†, Seung-Kook Park‡, Hyeokpil Kwon†, Sang Hyun Lee†, Kibaek Lee†,

6

Chang Hyun Nahm†, Sung Jun Jo†, Hyun-Suk Oh†, Pyung-Kyu Park§, Kwang-Ho Choo∥,

7

Chung-Hak Lee*,†, and Taewoo Yi,**,‡

8 9



School of Chemical and Biological Engineering, Seoul National University, Seoul 151-744,

10

Republic of Korea

11



12

Republic of Korea

13

§

14

Korea

15

Hanwha Engineering and Construction, 76, Gajeong-Ro, Yuseong-Gu, Daejeon 305-804,

Department of Environmental Engineering, Yonsei University, Wonju, 220-710, Republic of



Department of Environmental Engineering, Kyungpook National University, Daegu, 702-

16

701, Republic of Korea

17 18 19

*Corresponding author: Phone: +82-2-880-7075. Fax: +82-2-874-0896. E-mail: [email protected] **Corresponding author: Phone: +82-41-950-5874. Fax: +82-41-950-5934. E-mail: [email protected]

20 21

ABSTRACT

22

Quorum quenching (QQ) has recently been acknowledged to be a sustainable antifouling

23

strategy and has been investigated widely using lab-scale membrane bioreactor (MBR)

24

systems. This study attempted to bring this QQ-MBR closer to potential practical application.

25

Two types of pilot-scale QQ-MBRs with QQ bacteria entrapping beads (QQ-beads) were

26

installed and run at a wastewater treatment plant, feeding real municipal wastewater to test

27

the systems’ effectiveness for membrane fouling control and thus the amount of energy

28

savings, even under harsh environmental conditions. The rate of transmembrane pressure

29

(TMP) build-up was significantly mitigated in QQ-MBR compared to that in a conventional-

30

MBR. Consequently, QQ-MBR can substantially reduce energy consumption by reducing

31

coarse bubble aeration without compromising the effluent water quality. The addition of QQ1

ACS Paragon Plus Environment

Environmental Science & Technology

32

beads to a conventional MBR substantially affected the EPS concentrations, as well as

33

microbial floc size in the mixed liquor. Furthermore, the QQ activity and mechanical stability

34

of QQ-beads were well maintained for at least four months, indicating QQ-MBR has good

35

potential for practical applications.

36 37

INTRODUCTION

38

One of the pressing needs of people throughout the world is adequate supply of clean water.

39

Increasing water reuse through advanced wastewater treatment has become more urgent than

40

ever because of the water shortage accelerated by global population growth and climate

41

change.1, 2 For over thirty years, the membrane bioreactor (MBR) has attracted considerable

42

attention in the field of wastewater treatment and reuse. However, a critical issue in MBR

43

that awaits a technological advancement to solve is membrane biofouling, which leads to

44

high energy consumption and thus high operating costs.

45

Many studies utilizing diverse approaches have been conducted and reported to mitigate

46

this chronic issue of biofouling in MBRs, such as by modification of the membrane surface3,

47

by changes in physical cleaning strategies (such as back flushing, ultra-sonication,

48

mechanical cleaning, and vibration)4,5,6,7 or by adding specific media.7,8 Note that Yeon et al.9

49

revealed that quorum sensing plays a key role in biofilm formation on the membrane surface

50

in an MBR. Furthermore, they proved that the biofilm formation (biofouling) could be

51

mitigated substantially by disrupting signal molecules such as N-acyl homoserine lactones

52

(AHLs)10 using a quorum quenching enzyme.11,12,13,14 To overcome the drawbacks of

53

enzymatic quorum quenching, such as high cost of enzyme, bacterial quorum quenching was

54

developed.15,16,17,18,19,20,21,22 In detail, bacteria which produce quorum quenching enzymes

55

were isolated from a real MBR plant. Subsequently, those quorum quenching bacteria were

56

encapsulated in a vessel15,16,17,20 or entrapped in beads.18,21,22 They proved bacterial quorum

57

quenching is very efficient in both physical and biological effects on biofouling control in

58

MBR for wastewater treatment.

59

To date, however, most studies examining quorum quenching (QQ) MBR have been

60

performed in lab-scale reactors using synthetic wastewater. Although substantial mitigation

61

of biofouling by quorum quenching has been demonstrated, such an approach has not been

62

fully investigated in a larger pilot scale MBR using real wastewater. More often than not, the

63

microbial environment in lab-scale reactors is notably different from that in real full-scale 2

ACS Paragon Plus Environment

Page 2 of 22

Page 3 of 22

Environmental Science & Technology

64

reactors due to the different scales of the technological equipment and the different raw

65

wastewater characteristics.

66

The purpose of this study was to bring the QQ-MBR closer to potential practical

67

application by demonstrating the QQ effects in pilot-scale MBRs installed at a municipal

68

wastewater treatment plant and fed with real wastewater. Two MBR systems, one using a

69

one-stage (only one aerobic tank) process, and the other using a three-stage

70

(anaerobic/aerobic/membrane tanks) process, were operated for an extended period of more

71

than four months. To examine the life-span of encapsulated beads containing quorum

72

quenching bacteria under real wastewater condition, their QQ activity was monitored

73

regularly for that period. Considering that QQ may affect microbial floc size and extracellular

74

polymeric substance (EPS), the changes of protein, polysaccharide concentrations and floc

75

size distribution were monitored during the operation of conventional and QQ-MBRs. The

76

energy savings through the QQ-MBR was also evaluated relative to the energy consumption

77

of a conventional MBR.

78 79

MATERIALS AND METHODS

80 81

Preparation of the QQ-beads

82

QQ-beads were prepared using dripping method. However, the material and solidification

83

methods were modified to reinforce their stability by mixing polyvinyl alcohol and sodium

84

alginate solutions because QQ-beads made of alginate matrix are easily decomposed in real

85

wastewater. The mixture of polyvinyl alcohol, alginate and Rhodococcus sp. BH4 was

86

dripped into CaCl2-boric acid solution to form beads. Then, the beads were immersed in

87

sodium sulfate solution and stored in water. Rhodococcus sp. BH4, which was isolated from

88

a real MBR plant was used as a QQ bacterium in this study because its biofouling control

89

effect in MBR has been confirmed in a number of previous studies using synthetic

90

wastewater15,16,19,22 as well as it was reported to be capable of degrading a wide range of AHL

91

molecules by AHL-lactonase.24 The concentration of QQ bacteria (Rhodococcus sp. BH4) in

92

beads was approximately 4~5 mg per g of beads. The average size and density of QQ-beads

93

were approximately 4.3 mm and 1.05 g/mL, respectively.

94 95

MBR configurations and operation conditions 3

ACS Paragon Plus Environment

Environmental Science & Technology

96

The two types of pilot-scale submerged MBRs, one- and three-stage MBRs, were installed at

97

a municipal wastewater treatment plant (Daejeon, Korea), as shown in Figure 1. The one-

98

stage MBR consisted of only an aerobic membrane tank which is a simple MBR system

99

mostly used in previous studies. In the one-stage MBR, two types of aeration devices were

100

equipped: one for oxygen supply to activated sludge, and the other for membrane scouring

101

(Figure 1a). The air supply for the microorganisms was constantly maintained at 10 L/min

102

during the entire operation period, whereas the air scrubbing volumes for membrane cleaning

103

were varied 0.3 ~ 0.9 SADm (specific aeration demand per membrane area, m3/m2/h). Two

104

one-stage MBRs with a working volume of 80 L of each were operated in parallel. In phase 1,

105

one reactor was used for a vacant-MBR (with vacant-beads) and the other was used for a QQ-

106

MBR (with QQ-beads). Same intensity of membrane aeration was maintained at 0.3 SADm

107

for both MBRs to confirm the QQ effect in real wastewater. In phase 2, one reactor was used

108

for a conventional-MBR (without bead) and the other was used for a QQ-MBR. Different

109

membrane aeration intensity was applied to investigate the potential of energy savings for

110

QQ-MBR, i.e., 0.9 SADm for the conventional-MBR whereas 0.3 SADm for QQ-MBR. For

111

each one-stage MBR, three C-PVC membranes with a pore size of 0.4 µm (Pure-envitech,

112

Korea) and an effective total surface area of 0.9 m2 were used. The flux was maintained at a

113

constant 20 L/m2/h (LMH) in a continuous cycle of filtration (10 minutes), followed by

114

relaxation (two minutes).

115

A real conventional MBR system is composed of biological nutrient removal processes,

116

such as anoxic-aerobic (A/O) or anaerobic–anoxic–aerobic (A2O) processes. To bring the

117

QQ-MBR closer to potential practical application, the one-stage MBR was expanded to a

118

three-stage MBR with an additional anoxic process for nutrient removal. The three-stage

119

MBR consisted of an anoxic, an aerobic and a membrane tank. An air diffuser was equipped

120

in each of the aerobic and membrane tanks (Figure 1b). Two three-stage MBRs were

121

operated in parallel: one was a conventional-MBR (without beads) and the other was a QQ-

122

MBR (with QQ-beads). Polyethersulfone membranes with a pore size of 0.04 µm (Microdyn-

123

Nadir, Germany) were applied, giving an effective total surface area of 3.5 m3 to each MBR.

124

Identical diffusers were equipped in each aerobic tank for oxygen supply and in each

125

membrane tank for membrane cleaning. The aeration rate for oxygen supply and membrane

126

cleaning were constantly maintained at 8 L/min in an aerobic tank and 0.34 SADm in a

127

membrane tank, respectively. The flux was maintained at 15 L/m2/h (LMH) in a continuous

128

cycle of filtration (10 minutes) followed by relaxation (2 minutes). Influent was fed into the 4

ACS Paragon Plus Environment

Page 4 of 22

Page 5 of 22

Environmental Science & Technology

129

anoxic tank, while activated sludge in the membrane tank was continuously recirculated into

130

anoxic tank with a recirculation rate of 2.5 Q.

131

In both types of MBRs, activated sludge was directly taken from the wastewater treatment

132

plant and real wastewater, which passed sedimentation tank and screen, was fed as the

133

influent. A mesh screen (size: about 2 mm) was placed in the membrane tank so that vacant-

134

or QQ-beads (size: about 4.3 mm) were constantly retained in the membrane tank in each

135

MBR. TMP is defined as the pressure difference between broth and permeate side of a

136

membrane in a submerged MBR. The extent of biofouling in each MBR was quantitatively

137

evaluated by monitoring the TMP which increases to compensate for the membrane-fouling

138

under constant flux operation. When the TMP reached above 25 kPa during the MBR

139

operation, used membrane was taken out and chemical washing with 1,000 ppm of NaOCl

140

solution was conducted, which resulted in more than 96% of permeability recovery. The

141

operating conditions of each MBR and other important specifications are provided in Table 1.

142 143

Bioassay for the detection of QS bacteria producing AHLs

144

LB agar covered with X-Gal (5-bromo-4-chloro-3-indolyl-β-d-galactopyranoside) was used

145

for the bioassay. These assays consisted of streaking the AHL reporter strain, A. tumefaciens

146

A13623, on the plate, and then placing each sample to be tested. If the sample produces or

147

contains AHLs, then they diffuse through the agar, developing a blue color in the reporter

148

strain as a result. Positive and negative controls consisted of standard C8-HSL and distilled

149

water, respectively.

150 151

Bioluminescence assay for measuring the AHLs

152

The AHL molecules were measured via a bioluminescence assay24. First, the reporter strains

153

of A. tumefaciens A136 and the AHL sample were mixed and loaded into 96-well-plate. The

154

plate was placed on an incubator to maintain the temperature at 30 °C for 90 min, and then

155

Beta-Glo® Assay System (Promega, USA) solution was added into each well. After 40 min,

156

the luminescence intensity was measured by using a luminometer (Synergy 2, Bio-Tek, USA).

157

The concentration of AHL samples were determined by plotting the calibration curve of

158

standard AHLs.

159 160

Measurement of the biological and mechanical stability of the QQ-beads 5

ACS Paragon Plus Environment

Environmental Science & Technology

161

The activity of QQ-beads was determined by the degradation rate of C8-HSL (N-octanoyl-DL-

162

homoserine lactone). C8-HSL was chosen as a representative AHL molecule because it is one

163

of the dominant AHL molecules in MBRs for wastewater treatment.9,15 Standard C8-HSL

164

(Sigma Aldrich, USA) was dissolved in Tris-HCl buffer (50 mM, pH 7) to a final

165

concentration of 200 nM. Next, 50 QQ-beads were added to 20 mL of the C8-HSL solution

166

and then reacted using orbital shaker at 50 rpm at 25 °C. The residual concentration of C8-

167

HSL was measured using a bioluminescence assay. To determine the biological stability of

168

QQ bead in a continuous MBR, 50 QQ-beads were withdrawn and strongly washed for

169

measurement of the residual QQ activity. The relative QQ activity at each time point was

170

calculated by the ratio of residual activity to initial activity. Furthermore, the viability of the

171

entrapped BH4 into QQ-beads was visually observed using a confocal laser scanning

172

microscope (CLSM, C1 plus, Nikon, Japan) after staining with live/dead kit (Molecular

173

Probes, USA).

174

To investigate the mechanical stability of QQ-beads during MBR operation, compression

175

tests were performed using a texture analyzer (CT3 4500, Brookfield, USA) at a mobile

176

probe (TA44) speed of 0.5 mm/s up to 50% deformation of beads. The hardness work, a

177

measure of energy required to compress the sample, was calculated as the area under the

178

curve of the compression plot.21

179 180

Analytical methods

181

EPS (extracellular polymeric substances) concentrations in the mixed liquor and the biofilm

182

were analyzed in both vacant- and QQ-MBRs. Soluble EPS were obtained by centrifuging the

183

mixed liquor (6000 rpm, 10 min) and then filtering the supernatant through a 0.45-µm syringe

184

filter. Bound EPS was extracted from the pellet (activated sludge floc). EPS in the biofilm

185

was obtained as follows. First, a used membrane was taken from a membrane tank and briefly

186

washed with tap water. Next, the biofilm was detached from the used membrane via

187

sonication (10 min) and then extracted using the modified thermal extraction method.25 The

188

proteins and polysaccharides in the EPS were quantitatively determined using the Bradford

189

assay and the phenol-sulfuric acid method, respectively.26

190

Mixed liquor suspended solid (MLSS), chemical oxygen demand (COD), total nitrogen

191

(TN) and ammonia-nitrogen (NH4-N) were measured according to standard methods. The

192

average floc size was measured using a particle size analyzer (Microtrac S3500).

193 6

ACS Paragon Plus Environment

Page 6 of 22

Page 7 of 22

194

Environmental Science & Technology

RESULTS AND DISCUSSION

195 196

QQ effects on the performance of the one-stage MBR fed with real wastewater

197

The pilot-scale MBR experiments were conducted to investigate the influence of real

198

wastewater on QQ effect instead of the synthetic wastewater because the characteristics of

199

influent wastewater should have a large impact on MBR performance.27 Prior to applying

200

QQ-beads into the MBRs, a bioassay test was conducted to confirm the presence of QS

201

bacteria producing AHLs in the real wastewater. As shown in Figure S1, it was revealed that

202

QS bacteria existed in the feed wastewater as well as the activated sludge used for inoculum

203

in this study. In phase 1, vacant-beads with no QQ-bacterium and QQ-beads entrapped with

204

QQ-bacteria were placed into the first one-stage MBR (Vacant-MBR) and the second one-

205

stage MBR (QQ-MBR), respectively. The loading rate of the beads in each one-stage MBR

206

was 1% in v/v (volume of beads/volume of reactor), while the same intensity of membrane

207

aeration was maintained at 0.3 m3/m2/h (SADm) for both MBRs.

208

As shown in Figure 2a, the rate of TMP build-up, which reflects the extent of membrane

209

biofouling, was delayed by approximately 500% in the QQ-MBR compared with that in the

210

vacant-MBR. Biofouling reduction in QQ-MBR could be attributed to both a biological effect

211

due to quorum quenching of the QQ-beads and a physical effect due to friction between the

212

beads and the membrane. Assuming that the physical cleaning effect by beads would be

213

identical in both vacant- and QQ-MBRs because of the equal bead loading, the delay of the

214

TMP build-up rate in QQ-MBR can be attributed solely to the QQ activity of the QQ-beads.

215

The characteristics of real wastewater are more variable and unsteady, unlike that of synthetic

216

wastewater, as shown in Figure S2. Note that biofouling control through bacterial QQ can

217

also be achieved in an MBR, which suggests the QQ-MBR is approaching closer and closer

218

to practical application.

219 220

QQ effects on EPS relevant to biofouling

221

Quorum sensing is known to be the cell-to-cell communication between microorganisms,

222

which determines phenotypes, such as secretion of EPS, biofilm formation, and virulence.28,29

223

Many previous studies on QQ-MBR using synthetic wastewater reported that the

224

concentration of EPS was decreased in a QQ-MBR.12,18,19,20,22 To confirm the change in EPS

225

concentration in the QQ-MBR fed with real wastewater, EPS analysis of the mixed liquor and

226

the biocake were conducted for both vacant- and QQ-MBRs. 7

ACS Paragon Plus Environment

Environmental Science & Technology

227

After the same operating period of 14 days, the used membrane modules were taken out

228

from both vacant- and QQ-MBRs to measure the amount of total attached biomass (TAB)

229

and EPS in the biocake on the membrane surface. Mixed liquor in each MBR was also

230

sampled to measure the total (i.e., polysaccharides plus protein) soluble and bound EPS (EPS

231

in activated sludge floc). The total soluble and the total bound EPS in the mixed liquor in the

232

QQ-MBR were reduced by approximately 60% (Figure 3a) and 15% (Figure 3b), respectively,

233

compared to those in the vacant-MBR. It has been reported that the soluble EPS may have

234

great influence on the membrane-biofouling in MBR.30,31,32 Especially, Wisniewski et al.32

235

revealed the significant role of the soluble fraction of EPS on membrane permeability. Thus,

236

even though our results show that the amount of soluble EPS was much smaller than that of

237

bound EPS in the mixed liquor, the 60% reduction of soluble EPS through QQ-beads could

238

substantially mitigate the biofouling in QQ-MBR. The TAB per unit area of membrane in the

239

vacant-MBR (420 mg/m2) was much greater than that in the QQ-MBR (60 mg/m2), indicating

240

much lower biomass was accumulated on the membrane surface in QQ-MBR after the same

241

operation period. Moreover, the concentration of polysaccharide per unit membrane surface

242

was significantly reduced in the QQ-MBR (Figure 3c). It has been reported that EPS plays a

243

great role in biofilm formation and is also a key foulant of membrane-biofouling in an

244

MBR.30,33,34,35 Thus, one of the main reasons why QQ-beads mitigate biofouling in MBR fed

245

with real wastewater could be a reduction of soluble EPS in the mixed liquor as well as the

246

reduction of EPS in the biocake.

247

Although TMP rise-up rate was delayed, membrane-fouling still occurred in QQ-MBR. It

248

may be related to other membrane-fouling mechanisms such as pore blocking, sludge

249

accumulation, and other types of quorum sensing.

250 251

Comparison of the energy consumption between conventional- and QQ-MBRs

252

In submerged MBR systems, coarse bubble aeration for membrane scouring is a major energy

253

consumer, often exceeding 50% share of the total energy consumption (Figure S3).

254

Consequently, many efforts36,37 have been made and reported to reduce the energy consumed

255

for membrane scouring. As we confirmed that the rate of TMP rise-up was substantially

256

delayed in the QQ-MBR, we attempted to quantitatively evaluate how much energy savings

257

would be achieved by the addition of QQ-beads. For that purpose, the conventional- and QQ-

258

MBRs were run in parallel, applying the same aeration intensity for the oxygen supply, but 8

ACS Paragon Plus Environment

Page 8 of 22

Page 9 of 22

Environmental Science & Technology

259

with different coarse bubble aeration conditions for membrane cleaning. The specific aeration

260

demand per membrane surface area (SADm) was 0.9 m3/m2/h for the conventional-MBR,

261

whereas it was 0.3 m3/m2/h for the QQ-MBR. In other words, the membrane aeration

262

intensity in the QQ-MBR was reduced to one third of that in the conventional-MBR. As

263

shown in Figure 2b, even though the conventional-MBR was operated at threefold greater air

264

scrubbing intensity, the TMP rise-up rate in the conventional-MBR was faster than that in the

265

QQ-MBR.

266

Based on Figure 2b, the specific filtration energy required for permeate suction and specific

267

aeration energy for membrane cleaning in one-stage MBRs were estimated using equations (1)

268

& (2), which were derived with some assumptions described in the SI. Figure 4 shows a

269

comparison of the specific energy consumed for filtration (permeate suction) and air

270

scrubbing between the conventional- and QQ-MBRs. The difference in the filtration energy

271

consumption was not as high as that in air scrubbing for membrane cleaning. Note that the

272

specific energy consumption for membrane scouring in the conventional-MBR was

273

approximately three-times greater than that in the QQ-MBR. The specific energy

274

consumption for both items was approximately 0.46 kWh/m3 in the conventional-MBR,

275

whereas the amount was 0.20 kWh/m3 in the QQ-MBR. In short, QQ-MBR could reduce the

276

biofouling related energy consumption by approximately 60%. In addition, considering the

277

labor and chemical costs required for chemical cleaning of the used membranes, the operating

278

cost could further be reduced in the QQ-MBR.

279 280

QQ effect in the three-stage MBR fed with real wastewater

281

Figure 5 shows the profiles of TMP rise-up in the conventional- and QQ-MBRs operated at

282

the same aeration intensity (0.34 m3/m2/h). It took approximately 18 days in the

283

conventional-MBR, whereas it took 35 days in the QQ-MBR, to reach the TMP of 20 kPa. In

284

other words, the rate of TMP rise-up was delayed by approximately 100% in the QQ-MBR

285

through the addition of QQ-beads to the membrane tank. This result indicates that the QQ

286

effect on the membrane fouling is also valid in the three-stage MBR system with an anoxic

287

process. However, the extent of the delay of TMP rise-up decreased from 500% (Figure 2a)

288

for the one-stage MBR to 100% (Figure 5) in the three-stage MBR. This reduced

289

performance might be attributed to the activated sludge recycle throughout the three tanks

290

and/or the considerably smaller loading volume of the QQ-beads (v/v) in the three-stage

291

MBR [0.27% (v/v)], which was approximately one-third of that in the one-stage MBR [1% 9

ACS Paragon Plus Environment

Environmental Science & Technology

292

(v/v)]. Further research should be performed to determine the best operating conditions that

293

are able to optimize the use of the QQ-beads in the QQ-MBR. In addition, the difference of

294

MBR process between the one- and three-stage MBRs could give rise to the change of

295

microbial community, which might be another cause of reduced performance.

296 297

QQ effect on the floc size of the activated sludge

298

Microbial floc size is one of the important factors of the floc characteristics and is related to

299

membrane-biofouling.38,39 However, some reports on the QS/QQ effects on floc size are

300

contradictory to each other. It was reported that the granule formation and size is closely

301

related to AHL-based QS.40, 41 Jiang et al.14 found that the size of the activated sludge floc

302

was decreased by quorum quenching. However, Weerasekara et al.19 reported the change of

303

microbial floc size could be attributed to microbial adaptation when seeded into a new reactor,

304

instead of the effect of QQ.

305

In this work, in the one-stage MBR, the average floc size in the conventional-MBR was

306

106 µm, but that in the QQ-MBR was 88 µm (approximately 20% reduction), as shown in

307

Figure S4 and Figure 6. In the three-stage MBR, however, the floc size in all three tanks

308

became much smaller than that in one-stage MBRs. Moreover, no significant difference of

309

the average floc size was observed, not only between three tanks but also between the

310

conventional- and QQ-MBRs in each tank. Kim et al.33 and McMillan et al.42 mentioned that

311

activated sludge can be mechanically broken by the pumping device. In the three-stage MBR,

312

microbial flocs are continuously recirculated via the high flow rate of the recirculation pump

313

(2.5Q, 1.7 L/min), so that they could be broken mechanically by pumping shear, which may

314

be more powerful than the QQ effect. Consequently, the microbial floc size would be

315

equalized, regardless of the tank types.

316 317

QQ effect on the effluent quality

318

QQ-MBR inhibited biofouling and thus could substantially reduce the energy consumption of

319

the MBR. However, we cannot go further without verifying the effluent water quality in the

320

QQ-MBR because it must be one of the main factors in the evaluation of MBR performance.

321

It has been reported that certain nitrifying, denitrifying and nitrogen fixation bacteria were

322

involved in quorum sensing.43,44,45,46 In addition, QQ could affect the metabolism of QS 10

ACS Paragon Plus Environment

Page 10 of 22

Page 11 of 22

323

Environmental Science & Technology

bacteria in the activated sludge.

324

We monitored the removal efficiencies of some pollutants, such as COD, T-N, NH4-N and

325

NO3-N for one-stage and three-stage MBRs. However, there was no significant difference

326

between conventional- and QQ-MBRs in both one-stage and three-stage MBRs (Figure 7 and

327

Table S2). This result indicates that quorum quenching has no adverse effect on the effluent

328

water quality in QQ-MBR fed with real wastewater.

329 330

Stability of the QQ-beads in the long-term operation of the QQ-MBR

331

On the path toward the practical application of a QQ-MBR, long-term stability of the QQ-

332

beads is required because a short life span of QQ-beads would require their frequent

333

replacement, which would increase the operational cost of the QQ-MBR. Thus, the stability

334

of QQ-beads in terms of the QQ activity, viability and mechanical strength were tested during

335

the long-term (100 ~ 140 days) operation of both QQ-MBRs.

336

The used QQ-beads were intermittently removed from the aerobic tank (one-stage MBR)

337

or the membrane tank (three-stage MBR). Next, the relative QQ-activity, defined by the

338

degradation ratio of standard C8-HSL for 120 min in the presence of used QQ-beads, was

339

monitored and plotted against the operating time (Figure 8). In the one-stage QQ-MBR, the

340

relative activity of QQ-beads decreased by 40% of their initial activity during 25 days, but

341

increased slowly up to the initial QQ activity level after approximately 60 days. In the three-

342

stage MBR, the relative activity of QQ-beads decreased by approximately 10% to 20% of the

343

initial activity during 100 days of operation. A possible explanation for the initial decrease of

344

the QQ activities might be that the QQ bacteria were adapting themselves to the new

345

environment when they were exposed to the real wastewater.

346

In parallel with the relative QQ activity of the QQ-beads, live/dead cells in the QQ-beads

347

were also observed intermittently in the three-stage QQ-MBR to monitor the survival of the

348

QQ bacteria. Because it is nearly impossible for bacteria outside the beads to migrate into the

349

beads as shown in Figure S6, it had been concluded that cells shown in Figure S5 were

350

Rhodococucs Sp. BH4 which were initially entrapped into the QQ-beads. The population of

351

live cells (Figure S5a) appeared to be much higher than that of the dead cells (Figure S5b),

352

i.e., the viability of QQ bacteria were well maintained at least for 100 days. Consequently, it

353

is believed that QQ bacteria could live on the substrates and nutrients in real wastewater. In

354

addition, the relative mechanical strength of the QQ-beads, defined by the ratio of residual

355

mechanical strength to its initial value, was measured intermittently during 100 days 11

ACS Paragon Plus Environment

Environmental Science & Technology

356

operation. As shown in Figure S7, the change of the mechanical strength appeared to be

357

negligible.

358

All these results showed that the biological and mechanical stabilities of the QQ-beads were

359

well maintained, even in the harsh environment of real wastewater during the relatively long-

360

term operation of the QQ-MBR.

361

In summary, we demonstrated the effectiveness of quorum quenching for biofouling

362

control in two types of pilot-scale MBRs fed with real municipal wastewater. A QQ-MBR

363

with QQ bacteria entrapping beads could alleviate membrane fouling and thus could

364

significantly reduce energy consumption by reducing the aeration intensity required for

365

membrane cleaning compared with that in a conventional-MBR. Moreover, bacterial QQ was

366

determined to have no influence on the effluent water quality of the MBR systems. The QQ

367

activity, as well as mechanical stability of QQ-beads, was found to be well-maintained, even

368

under harsh real wastewater conditions, during the four months of operation. This study is

369

expected to bring QQ-MBR closer to possible practical applications.

370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396

Supporting Information Additional figures and table. This material is available free of charge via the Internet at http://pubs.acs.org. ACKNOWLEDGEMENTS This research was supported by the Commercializations Promotion Agency for R&D Outcomes (COMPA) (2014K000240) funded by the Ministry of Science, ICT and Future Planning (MISP) and Convergence Technology Program (2015001640001) funded by Korea Ministry of Environment (MOE). REFERENCES (1) Green, T. R.; Taniguchi, M.; Kooi, H.; Gurdak, J. J.; Allen, D. M.; Hiscock, K. M.; Treidel, H.; Aureli, A., Beneath the surface of global change: Impacts of climate change on groundwater. Journal of Hydrology 2011, 405, (3–4), 532-560. (2) Oki, T.; Kanae, S., Global hydrological cycles and world water resources. Science 2006, 313, (5790), 1068-72. (3) Liu, C. X.; Zhang, D. R.; He, Y.; Zhao, X. S.; Bai, R., Modification of membrane surface for anti-biofouling performance: Effect of anti-adhesion and anti-bacteria approaches. Journal of Membrane Science 2010, 346, (1), 121-130. (4) Judd, S., The MBR Book: Principles and Applications of Membrane Bioreactors for water and Wastewater Treatment, 2nd ed.; Elsevier: Amsterdam; Boston, 2011. (5) Kobayashi, T.; Kobayashi, T.; Hosaka, Y.; Fujii, N., Ultrasound-enhanced membranecleaning processes applied water treatments: influence of sonic frequency on filtration treatments. Ultrasonics 2003, 41, (3), 185-190. (6) van den Brink, P.; Vergeldt, F.; Van As, H.; Zwijnenburg, A.; Temmink, H.; van Loosdrecht, M. C. M., Potential of mechanical cleaning of membranes from a membrane bioreactor. Journal of 12

ACS Paragon Plus Environment

Page 12 of 22

Page 13 of 22

397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449

Environmental Science & Technology

Membrane Science 2013, 429, 259-267. (7) Yang, X.; Wang, R.; Fane, A. G.; Tang, C. Y.; Wenten, I. G., Membrane module design and dynamic shear-induced techniques to enhance liquid separation by hollow fiber modules: a review. Desalination and Water Treatment 2013, 51, (16-18), 3604-3627. (8) Lee, W.-N.; Kang, I.-J.; Lee, C.-H., Factors affecting filtration characteristics in membranecoupled moving bed biofilm reactor. Water Research 2006, 40, (9), 1827-1835. (9) Yeon, K. M.; Cheong, W. S.; Oh, H. S.; Lee, W. N.; Hwang, B. K.; Lee, C. H.; Beyenal, H.; Lewandowski, Z., Quorum sensing: a new biofouling control paradigm in a membrane bioreactor for advanced wastewater treatment. Environ Sci Technol 2009, 43, (2), 380-5. (10) Fuqua, C.; Parsek, M. R.; Greenberg, E. P., Regulation of gene expression by cell-to-cell communication: acyl-homoserine lactone quorum sensing. Annu Rev Genet 2001, 35, 439-68. (11) Yeon, K. M.; Lee, C. H.; Kim, J., Magnetic enzyme carrier for effective biofouling control in the membrane bioreactor based on enzymatic quorum quenching. Environ Sci Technol 2009, 43, (19), 7403-9. (12) Kim, J. H.; Choi, D. C.; Yeon, K. M.; Kim, S. R.; Lee, C. H., Enzyme-immobilized nanofiltration membrane to mitigate biofouling based on quorum quenching. Environ Sci Technol 2011, 45, (4), 1601-7. (13) Kim, H.-W.; Oh, H.-S.; Kim, S.-R.; Lee, K.-B.; Yeon, K.-M.; Lee, C.-H.; Kim, S.; Lee, J.-K., Microbial population dynamics and proteomics in membrane bioreactors with enzymatic quorum quenching. Appl Microbiol Biotechnol 2013, 97, (10), 4665-4675. (14) Jiang, W.; Xia, S.; Liang, J.; Zhang, Z.; Hermanowicz, S. W., Effect of quorum quenching on the reactor performance, biofouling and biomass characteristics in membrane bioreactors. Water Res 2013, 47, (1), 187-96. (15) Oh, H. S.; Yeon, K. M.; Yang, C. S.; Kim, S. R.; Lee, C. H.; Park, S. Y.; Han, J. Y.; Lee, J. K., Control of membrane biofouling in MBR for wastewater treatment by quorum quenching bacteria encapsulated in microporous membrane. Environ Sci Technol 2012, 46, (9), 4877-84. (16) Jahangir, D.; Oh, H.-S.; Kim, S.-R.; Park, P.-K.; Lee, C.-H.; Lee, J.-K., Specific location of encapsulated quorum quenching bacteria for biofouling control in an external submerged membrane bioreactor. Journal of Membrane Science 2012, 411–412, 130-136. (17) Cheong, W.-S.; Lee, C.-H.; Moon, Y.-H.; Oh, H.-S.; Kim, S.-R.; Lee, S. H.; Lee, C.-H.; Lee, J.-K., Isolation and Identification of Indigenous Quorum Quenching Bacteria, Pseudomonas sp. 1A1, for Biofouling Control in MBR. Industrial & Engineering Chemistry Research 2013, 52, (31), 1055410560. (18) Kim, S. R.; Oh, H. S.; Jo, S. J.; Yeon, K. M.; Lee, C. H.; Lim, D. J.; Lee, C. H.; Lee, J. K., Biofouling control with bead-entrapped quorum quenching bacteria in membrane bioreactors: physical and biological effects. Environ Sci Technol 2013, 47, (2), 836-42. (19) Weerasekara, N. A.; Choo, K.-H.; Lee, C.-H., Hybridization of physical cleaning and quorum quenching to minimize membrane biofouling and energy consumption in a membrane bioreactor. Water Research 2014, 67, 1-10. (20) Cheong, W. S.; Kim, S. R.; Oh, H. S.; Lee, S. H.; Yeon, K. M.; Lee, C. H.; Lee, J. K., Design of quorum quenching microbial vessel to enhance cell viability for biofouling control in membrane bioreactor. J Microbiol Biotechnol 2014, 24, (1), 97-105. (21) Kim, S.-R.; Lee, K.-B.; Kim, J.-E.; Won, Y.-J.; Yeon, K.-M.; Lee, C.-H.; Lim, D.-J., Macroencapsulation of quorum quenching bacteria by polymeric membrane layer and its application to MBR for biofouling control. Journal of Membrane Science 2015, 473, 109-117. (22) Maqbool, T.; Khan, S. J.; Waheed, H.; Lee, C.-H.; Hashmi, I.; Iqbal, H., Membrane biofouling retardation and improved sludge characteristics using quorum quenching bacteria in submerged membrane bioreactor. Journal of Membrane Science 2015, 483, 75-83. (23) Fuqua, C.; Winans, S. C., Conserved cis-acting promoter elements are required for densitydependent transcription of Agrobacterium tumefaciens conjugal transfer genes. Journal of Bacteriology 1996, 178, (2), 435-40. (24) Oh, H. S.; Kim, S. R.; Cheong, W. S.; Lee, C. H.; Lee, J. K., Biofouling inhibition in MBR by Rhodococcus sp. BH4 isolated from real MBR plant. Appl Microbiol Biotechnol 2013, 97, (23), 13

ACS Paragon Plus Environment

Environmental Science & Technology

450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502

10223-31. (25) Zhang, H.; Xia, J.; Yang, Y.; Wang, Z.; Yang, F., Mechanism of calcium mitigating membrane fouling in submerged membrane bioreactors. J Environ Sci (China) 2009, 21, (8), 1066-73. (26) DuBois, M.; Gilles, K. A.; Hamilton, J. K.; Rebers, P. A.; Smith, F., Colorimetric Method for Determination of Sugars and Related Substances. Analytical Chemistry 1956, 28, (3), 350-356. (27) Miura, Y.; Hiraiwa, M. N.; Ito, T.; Itonaga, T.; Watanabe, Y.; Okabe, S., Bacterial community structures in MBRs treating municipal wastewater: Relationship between community stability and reactor performance. Water Research 2007, 41, (3), 627-637. (28) Fuqua, C.; Winans, S. C.; Greenberg, E. P., Census and consensus in bacterial ecosystems: the LuxR-LuxI family of quorum-sensing transcriptional regulators. Annu Rev Microbiol 1996, 50, 727-51. (29) Dobretsov, S.; Teplitski, M.; Paul, V., Mini-review: quorum sensing in the marine environment and its relationship to biofouling. Biofouling 2009, 25, (5), 413-27. (30) Jarusutthirak, C.; Amy, G., Role of Soluble Microbial Products (SMP) in Membrane Fouling and Flux Decline. Environmental Science & Technology 2006, 40, (3), 969-974. (31) Rosenberger, S.; Laabs, C.; Lesjean, B.; Gnirss, R.; Amy, G.; Jekel, M.; Schrotter, J. C., Impact of colloidal and soluble organic material on membrane performance in membrane bioreactors for municipal wastewater treatment. Water Research 2006, 40, (4), 710-720. (32) Wisniewski, C.; Grasmick, A., Floc size distribution in a membrane bioreactor and consequences for membrane fouling. Colloids and Surfaces A: Physicochemical and Engineering Aspects 1998, 138, (2–3), 403-411. (33) Kim, J. S.; Lee, C. H.; Chang, I. S., Effect of pump shear on the performance of a crossflow membrane bioreactor. Water Res 2001, 35, (9), 2137-44. (34) Nagaoka, H.; Ueda, S.; Miya, A., Influence of bacterial extracellular polymers on the membrane separation activated sludge process. Water Science and Technology 1996, 34, (9), 165-172. (35) Wang, Z.; Wu, Z.; Tang, S., Extracellular polymeric substances (EPS) properties and their effects on membrane fouling in a submerged membrane bioreactor. Water Research 2009, 43, (9), 2504-2512. (36) Wu, J.; He, C., Effect of cyclic aeration on fouling in submerged membrane bioreactor for wastewater treatment. Water Research 2012, 46, (11), 3507-3515. (37) Siembida, B.; Cornel, P.; Krause, S.; Zimmermann, B., Effect of mechanical cleaning with granular material on the permeability of submerged membranes in the MBR process. Water Research 2010, 44, (14), 4037-4046. (38) Le-Clech, P.; Chen, V.; Fane, T. A. G., Fouling in membrane bioreactors used in wastewater treatment. Journal of Membrane Science 2006, 284, (1–2), 17-53. (39) Kang, I.-J.; Lee, C.-H.; Kim, K.-J., Characteristics of microfiltration membranes in a membrane coupled sequencing batch reactor system. Water Research 2003, 37, (5), 1192-1197. (40) Tan, C. H.; Koh, K. S.; Xie, C.; Tay, M.; Zhou, Y.; Williams, R.; Ng, W. J.; Rice, S. A.; Kjelleberg, S., The role of quorum sensing signalling in EPS production and the assembly of a sludge community into aerobic granules. ISME J 2014, 8, (6), 1186-1197. (41) Li, Y.; Lv, J.; Zhong, C.; Hao, W.; Wang, Y.; Zhu, J., Performance and role of N-acylhomoserine lactone (AHL)-based quorum sensing (QS) in aerobic granules. Journal of Environmental Sciences 2014, 26, (8), 1615-1621. (42) McMillan, J. D.; Wheaton, F. W.; Hochheimer, J. N.; Soares, J., Pumping effect on particle sizes in a recirculating aquaculture system. Aquacultural Engineering 2003, 27, (1), 53-59. (43) De Clippeleir, H.; Defoirdt, T.; Vanhaecke, L.; Vlaeminck, S.; Carballa, M.; Verstraete, W.; Boon, N., Long-chain acylhomoserine lactones increase the anoxic ammonium oxidation rate in an OLAND biofilm. Appl Microbiol Biotechnol 2011, 90, (4), 1511-1519. (44) Toyofuku, M.; Nomura, N.; Fujii, T.; Takaya, N.; Maseda, H.; Sawada, I.; Nakajima, T.; Uchiyama, H., Quorum Sensing Regulates Denitrification in Pseudomonas aeruginosa PAO1. Journal of Bacteriology 2007, 189, (13), 4969-4972. (45) Burton, E. O.; Read, H. W.; Pellitteri, M. C.; Hickey, W. J., Identification of AcylHomoserine Lactone Signal Molecules Produced by Nitrosomonas europaea Strain Schmidt. Applied 14

ACS Paragon Plus Environment

Page 14 of 22

Page 15 of 22

503 504 505 506 507 508 509

Environmental Science & Technology

and Environmental Microbiology 2005, 71, (8), 4906-4909. (46) Batchelor, S. E.; Cooper, M.; Chhabra, S. R.; Glover, L. A.; Stewart, G. S.; Williams, P.; Prosser, J. I., Cell density-regulated recovery of starved biofilm populations of ammonia-oxidizing bacteria. Appl Environ Microbiol 1997, 63, (6), 2281-6.

Table 1. MBR operating conditions One-stage MBR

Reactor type

510

Three-stage MBR

(Aerobic tank)

(Anoxic/aerobic/membrane tanks)

Total working volume (L)

80

450 (150 / 150 / 150)

Total HRT (h)

5.2

10.7

SRT (day)

25 days

Nearly infinite

Membrane type

C-PVC, Flat sheet

PES, Flat sheet

Membrane area (m2) / pore size (µm)

0.9 / 0.4

3.5 / 0.04

pH

6.5 ~ 7

6.5 ~ 7

MLSS (mg/L)

10,000 ~ 13,000

5,800 ~ 8,000

Flux (LMH)

20

15

Filtration mode (filtration/relaxation, min/min)

10 / 2

8/2

Aeration for oxygen supply (L/min)

10

8

Aeration for membrane scouring (SADm, m3/m2/h)

0.3 - 0.9

0.34

Concentration of beads (%, v(beads) / v(membrane tank))

1

0.8

SADm: specific aeration demand per membrane surface (m3/m2/h)

511

15

ACS Paragon Plus Environment

Environmental Science & Technology

512 513 514 515 516 517 518 519 520

Figure 1. MBR configurations. (a) Two one-stage MBRs in parallel, each of which consists of only a membrane tank where two types of aerations are equipped: one for oxygen supply to activated sludge, and the other for membrane scouring. (b) Two three-stage MBRs in parallel, each of which consists of an anoxic, an aerobic and a membrane tank.

16

ACS Paragon Plus Environment

Page 16 of 22

Page 17 of 22

521 522 523 524 525 526 527 528 529 530

Environmental Science & Technology

Figure 2. TMP profiles during the operation of two one-stage MBRs in two phases. (a) phase 1; TMP rise-up in the vacant- and QQ-MBRs at the same aeration intensity (SADm= 0.3 m3/m2/h). (b) phase 2; TMP rise-up in the conventional-MBR (SADm= 0.9 m3/m2/h) and QQMBR (SADm= 0.3 m3/m2/h) at the different aeration intensity.

531 532

(a)

17

ACS Paragon Plus Environment

Environmental Science & Technology

533 534

535 536 537 538 539 540 541 542

(b)

(c)

Figure 3. EPS analysis in one-stage vacant- and QQ-MBRs. (a) Soluble EPS. (b) Bound EPS (EPS in activated sludge floc). (c) EPS in biocake. *Concentration of polysaccharides in biocakes in QQ-MBR was below the detection limit. Each bar represents the average value of duplicate measurements. Error bar: standard deviation (n=2).

18

ACS Paragon Plus Environment

Page 18 of 22

Page 19 of 22

543 544 545 546 547 548 549

Environmental Science & Technology

Figure 4. Comparison of energy consumption related to biofouling between one-stage conventional- and QQ-MBRs. It was assumed that only two parameters, membrane aeration and filtration energy were affected by biofouling control of QQ.

19

ACS Paragon Plus Environment

Environmental Science & Technology

550 551 552 553

Figure 5. TMP profile of three-stage conventional- and QQ-MBRs at the same membrane aeration intensity (SADm= 0.34 m3/m2/h). 160

Average microbial floc size (um)

One-stage MBR (n=1) 140

Three-stage MBR (n=4)

Vacant-MBR QQ-MBR

Conventional-MBR QQ-MBR

120 100 80 60 40 20 0 Aerobic Aerobic tank

554

Anoxic tank

Aerobic tank Membrane tank

555

Figure 6. Average microbial floc size in one-stage and three-stage MBRs. Error bar: standard

556

deviation (n=4). 20

ACS Paragon Plus Environment

Page 20 of 22

Page 21 of 22

Environmental Science & Technology

120 One-stage MBR (n=4)

Removal efficiency (%)

100

Three-stage MBR (n=3)

Conventional-MBR QQ-MBR

80

60

40

20

0

COD 35 557

T-N 36

NH 374-N

COD 38

T-N 39

NH 404-N

558

Figure 7. Effluent water quality of one-stage and three-stage MBRs. (COD: chemical oxygen

559

demand, T-N: total nitrogen, NH4-N: ammonia-nitrogen). Error bar: standard deviation. (n=4

560

for one-stage MBR, n=3 for three-stage MBR).

561

21

ACS Paragon Plus Environment

Environmental Science & Technology

Page 22 of 22

1.2 One-stage MBR Three-stage MBR

Relative QQ activity

1.0

0.8

0.6

0.4

0.2

0.0 0

562 563 564 565 566 567

20

40

60

80

100

120

140

Time (day)

Figure 8. Variation of the relative QQ activity of the QQ-beads during the operation of onestage and three-stage MBRs. QQ activity: degradation ratio of standard C8-HSL for 120 min in the presence of QQ-beads. TOC/Abstract Art

568

22

ACS Paragon Plus Environment