DDT Vertical Migration and Formation of Accumulation Layer in

Jul 1, 2015 - Soil samples were collected at various depths (0.5–21.5 m) from ten boreholes that were drilled with a SH-30 Model Rig, four of which ...
1 downloads 5 Views 1MB Size
Subscriber access provided by Yale University Library

Article

DDT Vertical Migration and Formation of Accumulation Layer in Pesticide-Producing Sites Li Liu, Liping Bai, Changgeng Man, Wuhong Liang, Fasheng Li, and Xiaoguang Meng Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.5b02456 • Publication Date (Web): 01 Jul 2015 Downloaded from http://pubs.acs.org on July 10, 2015

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 27

Environmental Science & Technology

1

DDT Vertical Migration and Formation of Accumulation Layer in Pesticide-Producing Sites

2 3 4 5

Li Liu1,2*, Liping Bai1, Changgeng Man2, Wuhong Liang2, Fasheng Li1, Xiaoguang Meng1,2

6 7

1. State Key Laboratory of Environmental Criteria and Risk Assessment, Chinese Research Academy of Environmental Sciences, Beijing 100012, China 2. Center for Environmental Systems, Stevens Institute of Technology, Hoboken, NJ 07030, USA

Corresponding author phone: +1-201-216-8014; (+86-10)84915216; email: [email protected]

Abstract

8 9

Soil samples were collected at various depths (0.5-21.5m) from ten boreholes that were drilled with a

10

SH-30 Model Rig, four of which were at a dicofol production site while six were at a DDT

11

(dichlorodiphenyltrichloroethane) production site. In industrial sites, the shallow soils at depths of 0-2m

12

were mostly backfill soils, which cannot represent the contamination situation of the sites. The contaminated

13

levels in the deep original soil can represent the situation in contaminated sites. All the soil samples

14

investigated at the DDT and dicofol production sites were found to be seriously polluted. The contents of

15

both DDT (0.6-6071 mg/kg) and dicofol (0.5-1440 mg/kg) were much higher at the dicofol production site

16

than at the DDT production site (DDTs: 0.01-664.6 mg/kg, dicofol 1)4,5. Volatilization of DDTs from soil is a

43

continuing source of atmospheric contamination, which can be transported and transformed in vivo or in the

44

air6. They are normally considered persistent organic pollutants (POPs) that have more probability of 2

ACS Paragon Plus Environment

Page 2 of 27

Page 3 of 27

Environmental Science & Technology

45

impairing human health if the sites are reused in real estate development.

46

DDT production in China began in the early 1950s, with about 435,200 metric tons of DDTs were

47

produced between the 1950s and the 1980s7, accounting for 20% of total world production8,9. Although DDT

48

was banned from application and application in most countries in the 1980s, it is still in use for malaria

49

control and dicofol production in China10. From 1988 to 2002, nearly 54,000 tons of technical DDT were

50

used to produce about 40,000 tons of dicofol in China10. In partial fulfillment of the Stockholm Convention

51

on POPs, China endeavored to ban the open production of dicofol from DDT by 2009 and to accomplish

52

environmentally sound management and disposal of DDT wastes by 201511.

53

Most of the DDT contamination studies focused on agricultural areas12. It was reported that the ratio

54

o,p’-DDT/p,p’-DDT (Ro,p’/p,p’) in technical DDT was typically ~0.2, and contamination of dicofol type

55

was indicated when appeared with Ro,p’/p,p’ > 0.210,13. Widely differing Ro,p’/p,p’ values in dicofol

56

formulations can be found in the literature, with average values ranging from 0.2 to 7.010,14. Several studies

57

have investigated DDT in shallow soil at depths of 0 – 2 m in pesticide sites15,16. The soils within 2 m below

58

surface were mostly backfill. The shallow soil cannot represent the contamination situation of the sites. Few

59

studies referred to deep soil pollution of DDT production sites, especially that of dicofol production sites.

60

However, investigation of contamination in the deep soil at production sites could better illustrates the

61

vertical migration of contaminants and the sites situation.

62

In this study, DDT and dicofol production workshops of a pesticide factory in East China were selected as

63

typical contamination sites. This research presents the current status and the manner of migration and

64

transformation of OCP residues on contamination sites, and aims to reveal the distribution and sources of

65

OCP pollution in the pesticide production sites, which are different from agricultural soil, by examining

66

concentrations of DDTs and dicofol. The dataset generated will enrich and provide scientific information for 3

ACS Paragon Plus Environment

Environmental Science & Technology

67

remediation technology screening at contaminated sites such as pesticide factories.

68 69

2. Materials and methods

70

2.1. Site characterization

71

The pesticide factory is located in Shandong Province, East China, where the average annual temperature

72

is 12.6-13.1°C and annual precipitation is 500-700 mm. It was one of the earliest companies producing DDT,

73

which then stopped production according to the State Council’s directive in March 1983, and has not been

74

cleaned up yet.

75

A dicofol plant was built to produce 3000 ton/year of dicofol emulsifiable concentrate in December 1979

76

and was upgraded in 1981. The plant was shut down in 2008. DDT was used in production as raw material

77

for dicofol synthesis, which was firstly eliminated to DDE or chlorinated to Cl-DDT, then Cl-DDT was

78

hydrolyzed to form dicofol10. The reactions are shown in Fig. S1. in Supporting Information. The dicofol

79

products contained some DDT and Cl-DDT impurities. In order to reduce DDTs content in the products, the

80

alkaline eliminating process was added in this factory in 2000.

81

2.2. Soil sampling

82

Site investigation showed that the groundwater flows from east to west. The groundwater is located at the

83

silt layer or silty clay layer containing loess-doll with the depth of 4.2-8.5 m and the silty clay layer

84

containing loess-doll layer with the depth of 10.5-13.2 m. The soil layers at the depths of 6.6 -10.5 m and

85

12.5 - 16.0 m below the ground are aquicludes. The burial depth of the groundwater level is different in the

86

study area.

87

According to the groundwater flow and workshop distribution in the plant, a total of ten boreholes were

88

drilled with a SH-30 Model Rig, four of which were at the dicofol production site while six were at the DDT 4

ACS Paragon Plus Environment

Page 4 of 27

Page 5 of 27

Environmental Science & Technology

89

production site (Fig. 1). Soil samples were collected at different depths of the boreholes for vertical

90

migration study.

91

The four borehole locations at the dicofol production site (named S1, S2, S3, S4) were originally covered

92

with concrete that were 30 cm (S1), 150 cm (S2), 200 cm (S3) and 60 cm (S4) in thickness respectively. 31

93

samples were collected from these four boreholes. Soil was sampled every 0.5 m deep after the concrete

94

layer was removed and the soils exposed. Rocks were present at about 5 m deep in most of the boreholes.

95

Location description of the sampling points is shown in Table S1 in Supporting Information.

96

From the six boreholes (labeled D1, D2, D3, D4, D5, D6) at the DDT production site, 48 soil samples were

97

collected at different depths (0-21.5 m), according to the soil texture, surface disturbance depth, and on-site

98

test results by photoionization detector.

D1

S4

N

Dico fol pro (2002-20 ducing 08)

S1

Sampling

5

10 m

Pool

S2 Of fice

N

D6

Di cofol pr odu cin g (before 20 02 )

Trichloro methane

Drain 0

D4 Tank

Co nta ine r

Dicofol producing Po ol workshop

DDT producin g

Laboratory

D5

DDT producin g

S3 D3

DDT producing workshop

Packaging

Sampling 0

5

10 m

D2

99 Fig.1. Map of sampling sites.

100 101

The 79 soil samples were placed into cylindrical aluminum boxes, sealed for transport, and stored in the

102

laboratory at the temperature of 4°C. Each sample was tested for the concentrations of OCPs, including

103

DDTs and dicofol.

104

2.3. Sample extraction and preparation

105

The soil samples were air-dried, sieved through a 2 mm mesh, and ground. The samples were spiked with

106

2,4,5,6-tetrachloro-m-xylene (TCmX) and decachlorobiphenyl (PCB 209) as surrogate standards. In order to 5

ACS Paragon Plus Environment

Environmental Science & Technology

107

improve extraction efficiency, anhydrous sodium sulfate (5 g) and activated copper (2 g) were mixed with

108

the soil samples to remove water and sulfur in the sample. 5.0 g soil was extracted by accelerated solvent

109

extraction (ASE 300, Dionex, USA), using 100 mL 1:1 methylene chloride/acetone as extracting solvent.

110

The extracted solution samples were concentrated to approximately 1 mL with a K-D concentrator, and then

111

loaded onto a column (1 cm Φ) with a Florisil solid phase extraction cartridge (1 g, 6 mL, Supelco, USA)

112

filled with anhydrous sodium sulfate (2 g) for further clean-up. The column was eluted with acetone/hexane

113

(5/95, v/v, for about 5 min). Florisil and the anhydrous sodium sulfate were activated by heating at 400°C for

114

4 h before use. The eluate was solvent-exchanged to n-hexane (50 ml) and concentrated to a final volume of

115

1.0 mL under a gentle stream of nitrogen gas.

116

2.4. Chemical analysis

117

Dicofol and isomers and metabolites of DDT (p,p′-DDE, p,p′-DDD, p,p′-DDT and o,p′-DDT) were

118

quantified by a GC-ECD with dual columns. Analyses were done by an Agilent 6890 GC-ECD with

119

split/splitless injector, columns DB-608 (30 m×0.25 mm×0.25 µm) and DB-1701 (30 m×0.25 mm×0.25 µm).

120

The instrument oven program was as follows: initial temperature 100 °C held for 2 min, increased to 180 °C

121

at 30 °C/min and held for 1.5 min, ramp to 230 °C at 2 °C/min and held for 1 min, ramp to 240 °C at 1 °C/min

122

and held for 1 min, and then to 280 °C at 30 °C/min, maintained for 10 min. The sample injection volume

123

was 2 µL.

124

Physicochemical properties of the samples were rigorously examined including moisture content, pH,

125

CEC, and organic carbon. Soil moisture content was measured according to the national standard (GB

126

7172-1987, China). Soil pH was measured in water with the soil to water ratio of 1:2.5 (w/v). Soil organic

127

carbon (SOC) contents were measured using a Shimadzu 5000A TOC analyzer (Japan). Soil cation exchange

128

capacity (CEC) was the sum of Ca+Mg+K+Na extracted with 1 M NH4-acetate. CEC was measured by the 6

ACS Paragon Plus Environment

Page 6 of 27

Page 7 of 27

Environmental Science & Technology

129

method described by Yu et al3.

130

2.5. Quality control

131

Glassware was soaked in 5% K2Cr2O4 sulfuric acid solution overnight and then cleaned with distilled

132

water, then further rinsed with acetone and hexane. Calibration was carried out every time the GC was

133

restarted. For each OCP analysis, the correlation coefficients (r) of calibration curves were all higher than

134

0.9995. For each compound, the relative standard deviation (RSD) of the response factor was less than 10%.

135

All data were subject to strict quality control procedures, including the analysis of method blanks and

136

laboratory control samples. The compounds in blanks were undetected. The average recovery ratios of the

137

compounds obtained from the analysis of laboratory control sample were 70%-78%. Samples (n=10) were

138

extracted and measured in duplicate to evaluate the reproducibility of the overall method. TCmX and PCB

139

209 as recovery surrogates were added prior to extraction17. The average recovery ratios of surrogates were

140

91.5±8% and 93.6±10% for TCmX and PCB209, respectively. The method detection limit (MDL) was 0.1

141

mg/kg for the organochlorine pesticides.

142

3. Results and discussion

143

3.1. Vertical distributions of the contaminants at dicofol production site

144

Figure 2 illustrates the vertical distributions of DDT and dicofol in the soil profiles. DDTs and dicofol

145

were present in all samples, and the concentrations ranged from 0.6-6071 and 0.5-1440 mg/kg respectively.

146

Although the production was banned about 15 years ago, these OCPs were still present at high levels in most

147

of the soil layers. OCP residues remained in not only the top layer but also the deep layers, despite a long

148

period of degradation and transport. The concentration of OCP was much lower in the deep layers than those

149

in the top layer, which illustrated that OCP was difficult to migrate downward in soils.

150

The total OCP concentrations of S2 and S3, which were located in the center of the workshop, were much 7

ACS Paragon Plus Environment

Environmental Science & Technology

151

higher than those of S1 and S4 in the same soil layer. They were much higher than those not only in urban or

152

agricultural soils from various countries18-22, but also around a pesticide factory in Zibo city of China23,

153

while close to those in a heavily contaminated site24. In particular, S3 showed very high concentration levels,

154

among which the highest DDT concentration (6071 ppm) was in the soil layer at the depth of 2.0-2.5 m. The

155

concentrations of DDTs and dicofol were hundreds to thousands of ppm at 2.5 m below the soil surface. For

156

example, DDTs were 1217 ppm (3.0-3.5 m) while dicofol was 1440 ppm (2.5-3.0 m). Their concentrations

157

also reached 349 ppm and 230 ppm even at 5.0 m deep, respectively. Soils in S3 were seriously contaminated,

158

with much higher DDT and dicofol contents compared with the other three boreholes.

159

S2 was located between the two production workshops (Fig.1). In borehole S2, DDT and dicofol

160

concentrations were as high as 1196 ppm and 589 ppm at the depth of 1.5-2.0 m respectively, while they

161

were less than tens of ppm and kept falling below 2 m depth. DDT and dicofol contents in the soil from S4

162

were no higher than 20 ppm, 1.1-17 ppm and 0.5-14 ppm respectively, much lower than those of S2 and S3.

163

This reveals that it is difficult for DDTs and dicofol in soil to disseminate or migrate horizontally.

164

DDT and dicofol concentrations were high in each soil layer of S2, S3, and S4, illustrating serious leaks of

165

both production materials (DDTs) and completed products (dicofol) during the dicofol production process.

166

DDT and dicofol concentrations decreased with depth in S2, and S3. The contents of the contaminants in the

167

top layers were very high, and both their contents were higher at 2.5-3.0 m in S4. These boreholes shared

168

similar distribution patterns, revealing that the DDT and dicofol pollution here had the same pollution

169

sources, and that all resulted from leaks during dicofol production, not only before the year of 2000, but also

170

from recent production between 2000 (making dicofol) and 2008 (plant shutdown).

171

Borehole S1 was located in the area surrounding the original dicofol production workshop, and near the

172

wastewater pond. DDT and dicofol concentrations were less than tens of ppm, 0.6-61 ppm and 1.3-17 ppm 8

ACS Paragon Plus Environment

Page 8 of 27

Page 9 of 27

Environmental Science & Technology

173

respectively, significantly lower than those in the same layer of S2 and S3. As the result of a leak of the

174

wastewater pond, the vertical distributions pattern of DDT and dicofol contents in S1 were different from

175

those in the other three boreholes. The distribution patterns of DDTs and dicofol also had significant

176

differences in S1. The DDT concentration exhibited its highest value (61.2ppm) in the 0.3-0.6 m soil layer

177

and decreased with depth. In contrast, the dicofol content was comparatively low at this layer and increased

178

with depth, showing an opposite trend to that of DDTs. This suggested that they might have arisen from two

179

different pollution sources. S1 was located next to the wastewater pond, and its soil samples were deep grey,

180

soaked in liquid, and smelled pungent. Therefore, it can be deduced that there was penetration of wastewater

181

from the pond. Since these two pollutants exhibited different distributions, there was also leakage of DDTs

182

during the dicofol production process. In addition, the significantly high concentration of DDE proved that

183

degradation of OCPs was faster in wet soils when compared with dry soils25.

184 185 186 187 188 189 190 191

Fig. 2. Vertical distribution of dicofol and DDTs at dicofol production site

192 193

3.2. DDT isomers and metabolites at dicofol production site

194

In the dicofol production site, the DDE contents in soils made up the majority of total DDT concentrations, 9

ACS Paragon Plus Environment

Environmental Science & Technology

195

compared to the DDD contents (Fig. 2). In particular, the p,p'-DDE content in S1 soil constituted 87%. It was

196

not only higher than p,p'-DDD, but also higher than p,p'-DDT and o,p'-DDT. DDT present in the

197

environment could degrade to DDD and DDE through chemical and biological processes. Under anaerobic

198

conditions, the main metabolite is DDD, whereas under aerobic conditions, DDE is the most representative

199

metabolite26. So the DDD:DDE ratio can be selected as an index to indicate whether DDT is degraded under

200

aerobic or anaerobic conditions. Although the p,p'-DDE content was much higher than that of p,p'-DDD in

201

all samples in this study, ratios of DDE/DDD cannot indicate the DDT degradation condition in a dicofol

202

production site, which is different from agriculture soil, because DDE is an intermediate product in the

203

dicofol production process using DDT as starting material. The high content DDTs in the soil of the dicofol

204

production site suggested the source was leakage of the materials and products in the dicofol production

205

process.

206

In the dicofol production site, the DDE content generally decreases with depth from 2.0 m to 4.0 m in the

207

soil, probably because oxygen entered the soil largely by diffusion and gradually declined with the depth27.

208

This is in accordance with the conclusions of Zhao et al and Huang et al23,26. DDD is the anaerobic

209

degradation product of DDT, so the degradation of DDT to DDD is expected to increase with depth 26, which

210

is clearly because the oxygen content decreases with depth27.

211

A parameter to assess the application time of DDT is theRp,p’/p,p’ with the reference value of 1.019,

212

which is often used to indicate whether fresh technical DDT input is present28. A larger value means a longer

213

time application of DDTs. Rp,p’/p,p’ in the dicofol production site ranged from 0.6 to 23.5 in this study, with

214

an average value of 4.4. Most of the Rp,p’/p,p’ values were above 1.0, but not necessarily caused by old

215

inputs, because DDE constituted a major percentage. Especially in S1, DDE exhibited significantly high

216

values, even in the superficial layer (0.3-0.6 m). Technical DDT generally contains 75% p,p-DDT, 15% 10

ACS Paragon Plus Environment

Page 10 of 27

Page 11 of 27

Environmental Science & Technology

217

o,p-DDT, 5% p,p-DDE, and < 5% others29. The implementation of the Prohibition Directive 79/117/EEC by

218

European Commissions strictly limited DDT contents in dicofol to less than 0.1% (Council Directive

219

79/117/EEC, 1978). Two chemical industry sector standards of the People’s Republic of China

220

(HG3699-2002 and HG3700-2002) require DDT impurity to be no more than 0.5% of technical dicofol or no

221

more than 0.1% of formulated dicofol containing 20% dicofol. These standards had been implemented on

222

July 1, 2003. Considering the degradation in soils is usually slow, the high DDE contents cannot result from

223

degradation, but are probably due to the leak of some DDE intermediate products during the dicofol

224

production process. In the reaction of DDT as raw material for dicofol production, DDT was firstly

225

transformed to the intermediate DDE and Cl-DDT, then Cl-DDT was hydrolyzed to form dicofol as shown

226

in the reactions Fig. S1. in Supporting Information. As seen from the vertical distributions (Fig. 2), each soil

227

layer contained some dicofol, with the amount the same as the DDTs. This indicated that the contamination

228

inputs occurred in the recent dicofol production period, which was in accordance with the practical reality.

229

Therefore, the exact time of DDT inputs cannot be judged merely based on the value of Rp,p’/p,p’. The

230

conversion of p,p’-Cl-DDT to p,p’-DDE could lead to high p,p’-DDE/p,p’-DDT ratios and could mislead the

231

evaluation of p,p’-DDT residence time in the environment10.

232

During the synthesis reactions, on average 93% p,p’-DDT was converted to p,p’-dicofol, while only 37%

233

o,p’-DDT was converted to o,p’-dicofol. The o,p’-dicofol/p,p’-dicofol ratios were about 0.1, which was

234

much lower than 0.2-0.3 for o,p’-DDT/p,p’-DDT in technical DDT10,30. The ratio Ro,p’/p,p’ =

235

[o,p’-DDT]/[p,p’-DDT] can be used to distinguish technical DDT from “dicofol-type DDT”31, and can be

236

considered as an indicator to discriminate between dicofol or technical DDT usage. The values of Ro,p’/p,p

237

at the dicofol production site were generally between 0.4-5.8 in this study, further indicating the occurrence

238

of leaks of dicofol and DDTs that contained a large amount of DDE during the dicofol production process. 11

ACS Paragon Plus Environment

Environmental Science & Technology

239 240

3.3. Vertical distributions of the contaminants at DDT production site

241

Figure 3 illustrates the vertical distributions of DDTs and dicofol in the soil profiles at the former DDT

242

production site, and it clearly shows that the concentrations of DDTs (0.01-664.6ppm) were much higher

243

than those of dicofol, but much lower than in the soil of the former dicofol production site, especially in deep

244

layer soil. They were also much lower than the average concentrations of DDTs (3800–7300 mg/kg) found

245

in some reported heavily contaminated sites24, but much higher than in urban renewal soil in Beijing18. DDT

246

concentrations at this site were much higher than that in soils from Hong Kong (0.007-0.31 µg/kg)19, the

247

USA (