DEFOAMERS - Industrial & Engineering Chemistry (ACS Publications)

Hunt for habitable exoplanets needs new telescopes, report says · U.S. noncourt patent challenge system benefits generic drug makers, study says...
0 downloads 0 Views 409KB Size
346

INDUSTRIAL AND ENGINEERING CHEMISTRY

tal size, an increased concentration of such impurities tending to decrease the size of crystals. A new theory is developed based on the polarization effect of alkali metal vapor film deposited on the cathode surface. This theory readily accounts for the many phenomena-sometimes very perplexing-observed in the behavior of the various fused electrolyte baths, 118 well as the phenomena relative to the size and size distribution of the various metal crystals deposited a t the cathode. As there are no contradictory results brought forth by quite a number of runs in many fused salt baths of widely distinct physical and chemical properties, this new theory may be extended to include all electrolytic metal powders obtained from fused alkali salt baths. Finally, the term “metal powder” and the term “metal crystal” may be used interchangeably since all the electrolytic metal powders are polycrystalline powders or crystals.

Vol. 44, No. 2

ACKNOWLEDGMENT

The author wishes to express his most sincere appreciation to his teacher, Colin G. Fink of Columbia University, who succeeded in awakening in him a deep and lasting interest in the fields of powder metallurgy and electrochemistry. He also wishes to thank Francis M. Taylor and Louis V. Caserta, both of Tulane University, for their valuable assistance. LITERATURE CITED (1) Balke, C. W., IND. ENG.CHEM.,27, 1166-9 (1935). (2) Driggs, F. H., and Lilliendahl, W. C., Ibid., 22, 1302-3 (1930). (3) Ibid., 23, 634-7 (1931). (4) Fink, C. G., and Ma, C. C., Trans. Electrochem. SOC.,84, 33--52 (1943). (5) Ibid., pp. 53-63. (6) Fink, C. G., and Ma, C. C., U. S. Patent 2,463,367 (March 1 , 1949), (7) Ibid., 2,554,527 (May 29. 1951). RECEIVED Deoember 18, 1950.

DEFOAMERS ROY E. MORSE’ AND HENRY V. MOSS Food Technology Laboratory, Monsanto Chemical CQ., Anniston, Ala.

T

HE problem of foam control during the production of bakers’ yeast has been serious since Marquardt, following the teachings of Pasteur, introduced aeration into the process in 1879. The problem waa intensified by the introduction of the Hayduck process using molasses and ammonia as nutrients in 1915. The shortage of grains a t that time accelerated the changeover to the Hayduck process. Frey (4), and Frey, Kirby, and Schultz (6) described these developments in detail. The growth of microorganisms, especially yeast, is inevitably tied to the use of aeration because of fhe larger yields received. The exact mechanism whereby yields are increased has not been fully elucidated, but de Becze and Liebmann ( 1 ) in their all-encompassing review on aeration have listed most of the current theories. Gee and Gerhardt (6) have also attempted to throw light on this mechanism. Two general solutions to the foaming problem have been advanced-the use of mechanica1,foam breakers, such as are employed in the Waldhof fermenter, and the use of additives which destroy or control the foam. Ross (10, I I ) , and Ross and McBain ( l a ) have classified and illustrated the substances in common usage as additive defoamers. Equipment has been designed so that defomer addition is automatic as required. Stefaniak, Gailey, Brown, and Johnson (14) and Bilford, Scalf, Stark, and Kolachov (a)have described such equipment. Generally, additive defoamers rely upon the alteration in surface relationships, and Ross (11)has explained some of the factors involved. In the use of chemical additives as defoamers other important characteristics deserve consideration, I n yeast growth, yields may be seriously impaired, and in antibiotics manufacture, unit yields may be lowered. Goldshmidt and Koffler (7) have made a study of the effect of defoamers upon penicillin yield and have found that with the use of lard oils the yield of penicillin is increased significantly. They explained the enhanced yield as a result of the effect upon surface relationships of the organism itself, and show that it is not due simply to the mechanical destruction of foam, EXPERIMENTAL

A well-known and accepted technique for testing defoamers for use during yeast manufacture is not available. Goldshmidt and 1 Present sddrese, Direator of Research, Kingan and Co., Indianapolis 6, Ind.

Komer ( 7 ) have described a method for testing defoamers for use in penicillin manufacture and Sinsheimer ( I S ) has described a method for testing foam stability. The technique described herein is advanced as one suitable for use in testing yeast defoamers. The apparatus consists essentially of a device for passing cleaned, measured air through a mixture of yeast, molasses, and test defoamer at a controlled temperature; meanwhile, the time for defoamer failure is observed. The apparatus is shown in Figure I. Construction details are shown in Figures 2 and 3.

TESTPROCEDURE. With the foam column in place, the bath is brought to 30”C. Two grams of active dried yeast are added to 200 ml. of test molasses and the mixture is stirred mechanically a t medium speed for 5 minutes. Molasses is prepared by diluting dark table molasses to a s ecific gravity of 1.0390 (2Oo/2O0)after adjustment to pH 4.5. d r p l u s molasses may be preserved by processing in half-pint home canning jars a t 100’ C. for 25 minutes, followed by an air cool. This arrangement permits enough for one test per jar. Air flow is adjusted so that after adding the test mixture, the air rate is 0.125 cubic foot per minute. Air must be started before addition of test mixture. Foam forms immediately and starts to climb in the tower. When tower is half filled, 0.05 ml. of test defoamer is added. Defoamer should be near at hand when starting test, because foam rise in the tower is rapid. The time is observed and failure is considered t o be the point a t which foam fills the tower. The failure time is noted. At the conclusion of an 8-hour test run,. yeast is separated from the s ent molasses. The filtering device shown in Figure 4 was f o u n i t o facilitate this operation. After three washes with cold distilled water, odor and toxicity observations are made. PREPARATION OF FILTERIXG DEVICE.To a high-s eed wetted filter paper under suction on a Buchner funnel, a thicg slurry of highspeed filter aid is added. Sufficient filter aid is used to give a pad about 0.5 inch thick. Suction is continued and when the filter aid pad is formed, but before it is dry, another filter Paper is placed upon it. Water to a depth of about 1 inch is immediately added, which helps weld the “sandwich” into a unit. In his compilation of defoamers Ross (IO,1 1 ) has listed fatty acids as having value in controlling foam during yeast production. Tall oil seemed t o be an unexplored source of fatty acids for such an application. Dunlap, Hassel, and Maxwell ( 3 ) and

February 1952

INDUSTRIAL A N D ENGINEERING CHEMISTRY

341

.4 rough screening progrm whieli had mule merit was employed in the tall oil-ethylene oxide series. Four drop8 of test defoamer were added to 100 ml. of .cold distilled water, and thoroughly mixed. Those defoamers whictr went into solution immediately slwltys iailed, those which remained as a film upon the water were effective, and those showing very slight solution were most eiFeotive. These data are shown in Table I. DISCUSSION

The drioamer teating technique was iouad io be simple and reproducible. In the early phase of tho development of the defoamer test, yeast was addrlded to dilute molasses and poured directly into the foam tower. However, it was observed that in using this technique tho ntiture of the foam changed rather markedly a t about 20 minutes operating time. Mechanical premixing was found to climinate this f a a n chnrrge. As expected, some variation wxs encountered iu various lots of Yeast Defoamer Teat Apparatus

Figure I .

Ilcyi~olds(it) describe tall oil M being variable but having i t g a erul cooiposibion of: Ror,,, aeictx, %

40 45

Fatty acids. %

Sterolr % 1iydro;nrbonr

34-45 3--1

Keriiainder

Fatty irciii composition is as follows:

Because of the avxilability of reactive hydrogen groups, tu11 oil is capable oi reacting with ethylene oxide (EO) as described by McClellan (8). Uy reacting tnll oil with increasing various rnolar rat.ios of ethylene oxide it is possible io achieve products of increasing watar solubility due to change in hydrophil-Rydrophobe balance. Accordingly a nuniber of tall oil-ethylene oxidc condensation products were prepared arid testod as shown in Table I. hfotecular weight of refined t a l l oil used in these studies was assumed to he 300, crude tall oil 315, and ethylene oxide 41. For comparison, results with some other test deioamers are shown in Table II.

T A ~ LIE. TALLOIL-ETTIYLENE OXIDE(:ONDENBXIYON PRODUCTS r18 DEFOAMERS

Molar K a ~ i o Tali Ethylene Oil oxide

~~

1

0.00

W-stei Soi,*bi1ity Floating

fdiri

Foam Co"tn,i Time. Huiirr 2.5

Fi.'igure 2.

I

Suliible

12.00

Details of Yeast Defoamer Test Apparatus

Foam eniirneorl

* Msximum. 20 hours.

TABLE 11. DEFOAMERS FUR AERATEDYsm-hloLAsses brIXTURES E'onni Controi

Curupuund

Lordkyl aoid phoaljbato-I. 61 pnrta etiiylcsc oxide Hexyl acid plioil)iiat,o~~l. 4G pnrtsethylene oxide E t h I aoid phoaplinte-2.40 arts ethylene oxide 83dortirophosphorio acid-860 1)srts ethylene oxide Tetrsdooanol "-0ots;n"l D.C. Antifoani A

Ridceyl sleoim-3 0 partr elhyleur oxide Tridacyi alcohol-4.0 parts ethylene oxide Sz~orase-3 -its ethvlenc oxide Marimiim, 20 hours.

Time, Hour8

i,'ooain enhanord

0 1

Foam onlmnoed €?oam enhanced M*Xlm"I,i" 2 0

It was i w u d ndvisalh to stilrt tlw :airflow in the foarn tower beiore adding the test material, otherwise seepage through the fritted disk occurred, which gave a variable test volume and variable air flow. The maximum time employed was 20 hours; this is in excess of the time cycle normally employed during yeast pmduetion. Mod failures occurred within the first hour. The filtering technique was found to be fast. It is convenient, and the separated yeast a n be readily lifted from the "wndwieh" for toricity observations. If the test w m terminated during the growth phase of the yeast, filtration time ww always prolonged, . . .L

. L I ~ 1~~~ ~

I~

9~

.

I_

..

*...

.

.,

INDUSTRIAL AND ENGINEERING CHEMISTRY

348

Vol. 44, No. 2

daughter cells, and new issue. Toxic defoamers produced protracted filtration time, because of filter blocking by cellular debris and cell contents. Yeast growth data and microscopic observation are suggested for confirmation of toxicity tests. In all tests employing tall oil-thylene oxide condensation products no toxic effects were observed, either microscopically or by filtration performance. Further, no off-odor could be detected after washing.

FRITTED DISC

Figure 4.

Filter “Sandwich”

Yeast High speed filter aid C. High speed filter paper

A. B.

application. A substantiation of the experimental results has thus been achieved. Figure 3.

Details of Foam Tower

Ross ( 1 1 ) has stated that ‘‘the most complete defoamers are usually, but not always, insoluble. In some cases excess of an insoluble antifoam nullifies its effect; hence, in these cases there is an optimum amount where solubility is slightly exceeded.” With the approach presented in these studies a handy mechanism is a t hand for altering solubility of the defoaming agent. I t would appear from tlie data presented in Table I that complete insolubility is not as desirable in a defoamer as a partial orientation toward the aqueous phase. Thus, untreated tall oil is not as effective as that reacted with 0.7 mole of ethylene oxide, and 1 to 5 moles of ethylene oxide per mole of tall oil are even more effective. Further, with increasing solubility due to enlargement of the hydrophilic portion of the molecule, a lessening in defoamer efficiency is eacountered until a t a level of 12 moles of ethylene oxide foam enhancement is encountered. Summarizing, a correfation is apparent, starting with fair effectiveness in the low tall oil-ethylene oxide molar ratios, showing a peak in the range 1 to I to 1to 5 and falling off as the hydrophil portion of the molecule lengthens. Apparently a hydrophil-hydrophobe balance within the defoamer is necessary. Reference to Table I1 shows that compounds consisting of two hydrophilic portions such as sucroseethylene oxide and orthophosphoric acid-ethylene oxide are conipletely ineffective as defoamers and actually enhance foaming. As a result of these studies the tall 9il-ethylene oxide condensation product of a 1-to-1 mole ratio was selected as the most likely for plant test. Tests in yeast manufacturing plants have shown this compound to be extremely effective in its intended

ACKNOWLEDGMENT

The authors wish to express their gratitude to William B. Satkowski of the Anniston Laboratories, Phosphate Division, and Milton Kosmin of the Dayton Laboratories, Central Research Division of Monsanto Chemical Co., for the preparation of test materials used in this study and for their helpful criticism and suggestions during this study. LITERATURE CITED

(1) Becze, G. de, and Liebmann, A. J., IND. ENG.CHEM.,36, 882-90 (1944). (2) Bilford, H. R., Scalf, R. E., Stark, W. H., and Kolachov, P. J., Ibid., 34, 1406-10 (1942). (3) Dunlap, L. H., Hassel, L. V., and Maxwell, J. L., J. A m . 0 1 1 Chemists’ SOC.,27, 361-6 (1950). (4) Frey, C. N., IND. ENG.CHEY.,22, 1154-62 (1930). (5) Frey, C. N., Kirby, G. IT., and Sohultz, A.. Ibid., 28, 879-84 (1936). (6) Gee, C., and Gerhardt, P., J . Bact., 52, 271-82 (1946). (7) Goldshmidt, M. C., and Koffler, H., IND.ENG. CHEM.,42, 1819-23 (1950). (8) McClellan, P. P., Ibid., 42, 2402-7 (1950). (9) Reynolds, R. B., Southern Chemist, No. 1, 12 (1949). (10) Ross, S., Chem. Inds., 64, 757-9 (1949). (11) Ross, S., Rensselaer Polytechnic Institute, Bull. 63.40 pp., Troy, N. Y. (1950). (12) Ross, S., and McBain, J. W., IND.ENG. CHEY., 36, 570-3 (1944). (13) Sinsheimer, J. G., Soap S a d . Chemicals, 26, No. 8. 38-41 (1950). (14) Stefaniak, J. J., Gailey, F. B., Brown, C. S., and Johnson, M. J., IND.ENG.CHEM.,38, 666-71 (1946). RECEIVED April 16, 1951. Presented before t h e Division of Agricultural and Food Chemistry at the 119th Meeting of the AMERICAN CHEMICAL SOCIETY,Boston. Mass.