Design, Construction, and Operation of a Transported Fluid Bed

Jan 8, 2008 - Development Unit for Biomass Fast Pyrolysis: Effect of Pyrolysis Temperature ... unit, implementing the transported fluid bed reactor te...
0 downloads 0 Views 139KB Size
742

Ind. Eng. Chem. Res. 2008, 47, 742-747

PROCESS DESIGN AND CONTROL Design, Construction, and Operation of a Transported Fluid Bed Process Development Unit for Biomass Fast Pyrolysis: Effect of Pyrolysis Temperature A. A. Lappas,* V. S. Dimitropoulos, E. V. Antonakou, S. S. Voutetakis, and I. A. Vasalos Chemical Process Engineering Research Institute (CPERI), P.O. Box 361, 570 01 Thermi, Thessaloniki, Greece

The objective of this paper is to investigate biomass fast pyrolysis process in a novel once-through transported fluid bed process development unit. The main emphasis was given to the design and operation of this unit, which is made of several vessel modules. The main part of the unit is a specially designed mixing zone, where the solid heat carrier mixes with the biomass feed. The unit can process up to 20 g/min biomass and can circulate up to 300 g/min solid. Experiments showed that the unit could run effectively, with satisfactory stability and mass balances (92-96 wt % on biomass), under a wide range of experimental conditions. The yield of the raw total liquid product was up to 78 wt % on biomass basis. The effect of pyrolysis temperature on product yields is also presented in this paper: the temperature of 500 °C was found to be an optimum temperature for the maximization of the liquid product yields using a wood-based biomass. 1. Introduction Biomass has been identified as an alternative sustainable source of renewable energy. Among various technologies for the conversion of biomass to energy or to other materials (fuels, chemicals), fast pyrolysis is the most promising for industrial implementation.1 Biomass fast pyrolysis (BFP) is the thermal decomposition of biomass in an inert atmosphere using high heating rates and short residence times, of both solids and volatiles, at temperatures between 450 and 550 °C.2 In the BFP process, biomass is converted to vapors, gases, and char. The vapors condense to a liquid product called bio-oil. The selectivity of the process on various pyrolysis products varies, depending on the operating conditions. However, the main objective in a fast pyrolysis process is the maximization of the bio-oil yield. Bio-oil can be used either as a fuel for the production of heat or electricity,3 or as a transportation fuel after upgrading, either through hydrogenation4 or through gasification, followed by Fischer-Tropsch synthesis.5 Bio-oil is also a very important source of renewable chemicals and thus, biomass fast pyrolysis is considered to be a key process in the biorefinery of the future.6 According to previous work, the bio-oil production and quality can be optimized by properly selecting technologies and operating variables.7-11 It can be concluded that the main process variables that could affect the product yields, selectivities, and quality are the temperature, the heating rate (or equivalently, the biomass particle size), and the fast quenching of the vapors in order to prevent secondary cracking of the biooil components to lighter gaseous products.12 Based on these principles, several reactor configurations have been proposed in the literature, aiming at the maximization of the liquid yields.7 The oldest reactor type for BFP is the bubbling fluidized bed, which ensures high heat transfer rates from a solid heat carrier to the biomass particles.13 Since 1990 many large-scale pilot * To whom correspondence should be addressed. Tel.: +30-2310498305. Fax: +30-2310-498180. E-mail: [email protected].

plants have been constructed worldwide based on fluid bed technology. An example of such a process is the Union Fenoza unit in Spain14 with a capacity of 250 kg/h. Circulating fluid bed reactors (CFBs) or transported bed reactors have also been widely studied.10,15 Large-scale installations of CFB technology have operated by Red Arrow Products Inc. in Wisconsin. A CFB unit was also developed at Battelle’s Columbus Laboratories focusing mainly on biomass gasification.16 The Rotating Cone Reactor (RCR) technology, developed by Biomass Technology Group (BTG) B.V.,17 is the only European technology for biomass flash pyrolysis with effective performance in a scaling-up reactor system (250 kg/h). The principles of RCR are based on the CFB reactor. Other reactor types with a variety of applications are the vortex and ablative type reactors,18,19 the cyclonic reactors,20 the vacuum pyrolyzers,21 and the entrained flow reactors. Generally, in the 1990s several fast pyrolysis technologies were studied on a pilot or demonstration scale and approached a state of commercial status. However, the majority of these plants are not currently in operation mainly due to economic reasons. Today only the Dynamotive in Canada and BTG in Europe have announced demonstration installations with high biomass capacity of 2-4 tons/day.12 In this work a detailed description of the construction, design, and operation of a biomass fast pyrolysis process development unit, implementing the transported fluid bed reactor technology, will be presented. This unit was originally designed as an oilshale retort,22,23 and it was modified to a biomass pyrolyzer under the European Energy project BIOCAT (ENK6-CT200100510). Previous work was conducted in CPERI on biomass pyrolysis utilizing a CFB reactor after the proper modification of an existing fluid catalytic cracking (FCC) unit.24 The main problem with this unit was that its unstable operation under the modified operating conditions resulted in poor mass balances. Based on the experience gained from this study, a new unit has been constructed, with a flexibility to operate under a wide range of different biomass feeds and solid carriers.

10.1021/ie060990i CCC: $40.75 © 2008 American Chemical Society Published on Web 01/08/2008

Ind. Eng. Chem. Res., Vol. 47, No. 3, 2008 743

Figure 1. Schematic diagram of a process development unit for biomass pyrolysis. D201, mixing zone; D202, riser reactor; D101, regenerator; D301, stripper; D-304, solid heat carrier collection vessel; D61, biomass hopper; D-402, bio-oil first collection vessel; D-407, bio-oil second collection vessel; D-102, water collection vessel; F-101, flue gas filter; F-101, pyrolysis gas filter; HE-1, heat exchanger at regenerator exit; HE-401, heat exchanger at stripper exit; HE-403, heat exchanger at stabilizer; WTM-401, wet test meter for pyrolysis gas measurement. Table 1. Process Development Specifications operating variable

effective range

biomass feed rate biomass particle size range reactor temperature reactor pressure stripper temperature regenerator bed temperature regenerator capacity solid circulation rate feed hopper capacity vapor residence time

30-60 mL/min 50-800 µm 400-600 °C 1.7-3.0 atm 500-600 °C