Biodegradation of Volatile Chemicals in Soil: Separating Volatilization

Dec 3, 2018 - During environmental risk assessments of chemicals, higher-tier biodegradation tests in soil, sediment, and surface-water systems are re...
2 downloads 0 Views 895KB Size
Subscriber access provided by University of Winnipeg Library

Policy Analysis

Biodegradation of volatile chemicals in soil – Separating volatilization and degradation in improved test setup (OECD 307) Prasit Shrestha, Boris Meisterjahn, Michael Klein, Philipp Mayer, Heidi Birch, Christopher Hughes, and Dieter Hennecke Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.8b05079 • Publication Date (Web): 03 Dec 2018 Downloaded from http://pubs.acs.org on December 7, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 31

Environmental Science & Technology

O2

Volatile chemicals Improved test setup (OECD 307)

Complete Mass balance + Degradation Kinetics

Tetralin 1 1

Decane

Soil ACS Paragon Plus Environment

%aR(Mineralization)

60 40 20 0 0

% aR(Volatilization)

Environmental Science & Technology

30

60

90

20 0

40

30

30

10 0 0

30

60

90

120

60

0

3

6

9

12

0

3

6

9

12

20 10 0

60

% aR(NER)

%aR(NER)

40

40

20

Page 2 of 31

Decane

60

120

% aR(Volatilization)

%aR(Mineralization)

Tetralin

40

20

40

01A 02A 03G 04A

20 0

0 0

30

60

Time (days)

0 90 ACS Paragon 120 Plus Environment

3

6

Time (days)

9

12

Page 3 of 31

Environmental Science & Technology

1

Biodegradation of volatile chemicals in soil – Separating

2

volatilization and degradation in improved test setup

3

(OECD 307)

4

Prasit Shrestha1,2, Boris Meisterjahn1*, Michael Klein1, Philipp Mayer2, Heidi Birch2,

5

Christopher B. Hughes.3, Dieter Hennecke.1

6

1Fraunhofer

7

2Department

8

Lyngby, Denmark

9

3Ricardo

IME-AE, Auf dem Aberg 1, 57392 Schmallenberg Germany. of Environmental Engineering, Technical University Denmark, 2800 Kgs.

Energy and Environment, Harwell, OX11 0QR, UK

ACS Paragon Plus Environment

Environmental Science & Technology

10

Abstract

11

During environmental risk assessments of chemicals, higher tier biodegradation tests in soil,

12

sediment and/or surface water systems are required using standard OECD 307, 308 and 309

13

guidelines, respectively. These guidelines are not suitable for testing highly volatile chemicals

14

and recommend a biometer closed-incubation setup for testing slightly volatile chemicals. In

15

this setup, degradation kinetics of highly volatile chemicals can largely be influenced by

16

volatilization. Additionally, guidelines lack sufficient information on test system geometry and

17

guidance on how to measure and maintain aerobic conditions during the test. Our objectives

18

were 1) to design a closed test setup for biodegradation tests in soil, where maintaining and

19

measuring of aerobic conditions was possible without the loss of volatile test chemicals and 2)

20

to suggest data treatment measures for evaluating degradation kinetics of volatile test

21

chemicals. With the new setup, full scale OECD 307 tests were performed using the volatile

22

14C

23

balances were observed, and the new setup ensured that the volatilization losses were kept

24

below the mineralized fraction. Based on the obtained data an extended model was developed

25

that enabled considering volatilization in the modelling of degradation kinetics.

labelled chemicals decane and tetralin. For both test chemicals, reproducible complete mass

ACS Paragon Plus Environment

Page 4 of 31

Page 5 of 31

Environmental Science & Technology

26

1. Introduction

27

During prospective environmental risk assessment of chemicals, biodegradation kinetics data

28

are a key parameter in different regulatory frameworks like REACH1, Pesticide regulation2,

29

Biocide regulation3 etc. These degradation kinetics data are generated using a set of tiered

30

laboratory biodegradation tests with increasing levels of complexity4,5, which are performed

31

using standard OECD guidelines6. The highest tiers are formed by the environmental simulation

32

biodegradation tests and were designed to simulate biodegradation in various environmental

33

matrices such as soil (OECD 307)7, water/sediment (OECD 308)8 or surface water (OECD

34

309)9. The OECD guidelines were originally developed for pesticide regulation where they

35

work well with most of the relevant chemicals. However, when those guidelines are applied to

36

other regulatory frameworks it should be considered whether the chemicals regulated under

37

those frameworks posess different physical-chemical properties that might make them more

38

challenging to test or render the existing test guidelines unsuitable. In particular, the previously

39

mentioned guidelines face serious drawbacks when it comes to the testing of volatile chemicals.

40

Some of these issues are listed below:

41



Although the scope of OECD 307, 308 and 309 guidelines clearly state that the tests are

42

not suitable for volatile chemicals6,7, with the exception of OECD 309 they do not define

43

a threshold. In OECD 309 a threshold for the Henry´s law constant of 100 Pa m3/mol is

44

stated9.

45



When testing volatile chemicals in a flow-through setup, incomplete mass balances is a

46

major problem and it is often impossible to meet the validity criteria of 90%-110%

47

recovery for radiolabelled chemicals and 70% - 110% for non-labelled chemicals7-9.

48

Prior work has suggested that incomplete mass balances mainly result due to inability

49

of the traps to capture the volatile chemicals and hence they escape from the test setup.

50

In addition, our own experience and other studies indicate that volatile test chemicals

ACS Paragon Plus Environment

Environmental Science & Technology

51

are also being sorbed to the plastic or silicone materials present in the fittings of the test

52

setup.10

53



As an alternative, OECD 307, 308 and 309 allow to apply static biometer-type

54

incubation setups7,8. However, these guidelines give only limited information on how

55

to handle the headspace in the biometer type test setup for testing volatile chemicals.

56

Several studies suggest that the headspace volume is quite important to keep the system

57

aerobic in a static test setup. On the other hand too much headspace might lead to higher

58

mass distribution into the headspace volume leading to a lowered fraction in the water,

59

sediment or soil available for degradation, and a corresponding effect on degradation

60

kinetics10,11.

61



The guideline does not stipulate any data requirements to prove whether the test system

62

remains aerobic. This is a general problem with static test setups, especially if a co-

63

solvent is used for the application of test chemicals. In a normal case the co-solvent

64

should be evaporated after test substance application but during the application of

65

volatile chemicals the evaporation step has to be avoided as loss of test chemicals may

66

occur. However, our own studies with closed biometer type test setups have shown rapid

67

oxygen depletion after solvent application. This can have a major impact on the

68

degradation kinetics, but to monitor the oxygen content in the system containing volatile

69

chemicals is a challenging task.

70



As suggested by Birch et al. 201711, reductions in bioavailability as a result of

71

partitioning to headspace can largely influence the degradation kinetics. Therefore, new

72

data treatment methods are needed for generating meaningful degradation kinetics in

73

tests where volatile chemicals are used.

74

ACS Paragon Plus Environment

Page 6 of 31

Page 7 of 31

Environmental Science & Technology

75

To address these drawbacks, our objectives were: (1) to develop an incubation test for testing

76

degradation of volatile chemicals in soil; (2) to demonstrate the usefulness of the developed test

77

setup in a full scale OECD 307; and, (3) to suggest methods on how to treat the data obtained

78

from such tests for evaluating degradation kinetics. The first objective was obtained during a

79

series of pre-tests with different test setups. Maintainance of aerobic conditions inside the flask

80

was also taken into consideration and was done by external oxygen measurements thereby

81

minimizing test chemical losses due to opening of the vessel. Secondly, with the new test setup,

82

a full scale OECD 307 test was performed using two chemicals with different volatilization and

83

degradation potential and four different soils, varying in terms of texture, organic carbon (OC)

84

content and microbial activity. The data obtained were used to demonstrate the reproducibility

85

and reliability of the test setup in terms of mass balance. Thirdly, the data from the tests were

86

used to improve our understanding of different processess such as volatilization and sorption

87

processes taking place during the test and its influence on the final biodegradation data

88

obtained. Furthermore, data treatment methods were demonstrated for generating meaningful

89

degradation kinetics for the volatile chemicals in the new test setup. The first hypothesis of the

90

study was that improved methodology was necessary to determine the biodegradation kinetics

91

of hydrophobic volatile chemicals in soils. The second hypothesis was that careful experimental

92

testing and data analysis can facilitate the separation of degradation and evaporative losses.

93

94

2. Materials and methods

95

2.1. Test chemicals

96

Two 14C labelled chemicals were used for the degradation tests covered within this project: 1)

97

tetralin (1,2,3,4-tetrahydronaphthalene, C10H12, CAS no:119-64-2, Item no. 17445740, >98%

98

purity, Hartmann Analytics), and 2) decane (n-decane, C10H22, CAS no: 124-18-5, Item no.

ACS Paragon Plus Environment

Environmental Science & Technology

99

17539210, > 98% purity Hartmann Analytics). The test chemicals were selected based on their

100

differences in air-water partitioning and sorption properties with tetralin being slightly volatile

101

(KH 138 Pa m3 mol-1, VP 0.37 mmHg at 25°C and Koc 1068 L/kg)13 and decane being highly

102

volatile but theoretically more sorbing than tetralin (KH 522,000 Pa m3 mol-1, VP 1.43 mmHg

103

at 25°C and Koc 22,270 L/kg)12. For the optimisation of specific chemical analytics and also as

104

a quality control, cold standards from Sigma Aldrich with purity > 99% were used.

105

2.2. Soils

106

In total four soils were used to cover a broad range of soil texture, organic carbon (OC) content

107

and microbial biomass as required by the OECD guideline 307. Two soils with low OC content

108

01A (loamy sand, OC 0.80%) , 02A (silty loam, OC 0.98%) and two with higher OC content

109

03G (silty loam, OC 3.05%), 04A (loamy sand, OC 2.79%) were used. The detailed soil

110

properties are listed in Table S1. The soil texture was determined using the standard DIN ISO

111

1127713 and OC content was determined using DIN EN 1593614. As per the guideline

112

requirement, the soil was sampled from the upper 20 cm layer and was sieved using a 2 mm

113

sieve. The soils were maintained at 50% water holding capacity (WHC) for preincubation under

114

test conditions (at 20°C in the dark) for a period of 2-3 weeks before test start.

115

2.3. Test chemical application and sample incubation conditions

116

The 14C labelled test chemical application solution was prepared using the co-solvent acetone

117

for tetralin and methanol for decane. The application solution was then spiked directly on the

118

soil and the sample bottle was immediately closed using an insert cap. The starting test

119

substance concentration was 1 mg/kg (dw soil) for all tests conducted within this project. The

120

amount of applied radioactivity per soil sample of 50 g was 203 kBq in 219 µL acetone for

121

tetralin and 195 kBq in 139 µL methanol for decane. After application of the test chemical the

122

soil samples were incubated at 20 ± 2°C in the dark.

ACS Paragon Plus Environment

Page 8 of 31

Page 9 of 31

Environmental Science & Technology

123

2.4. Pre-tests

124

In order to develop a biodegradation test setup for volatile chemicals, a series of preliminary

125

tests were conducted using 14C labelled tetralin. The first tests comprised of a soil degradation

126

study using a flow-through setup as suggested by OECD 307 with slight modifications. The

127

primary objective of this experiment was to check for a complete mass balance of tetralin during

128

the incubation period. These tests were followed by other tests using closed flask test setups

129

where maintaining and measuring aerobic conditions in the test setup was considered along

130

with the complete mass balance of the test chemical.

131

2.4.1.

132

50 g dry weight (dw) of preincubated soil was weighed in a 100 mL sample flask and applied

133

with 14C labelled tetralin (see section 2.3). A flow-through setup consisted of a sample flask

134

connected with absorption traps containing 100 mL of 2N NaOH and ethylene glycol flasks to

135

trap mineralized 14CO2 and volatile parent/intermediate, respectively. A schematic diagram of

136

the flow-through setup used is given in the Figure S1. Behind the traps a tube furnace operating

137

at 850°C was connected, filled with a CuO catalyst in order to combust any substance in the

138

flow-through, which could not be captured in the prior traps. To trap the resulting 14CO2, one

139

further sample flask with 100 mL 2N NaOH was connected behind the oven. At specific

140

sampling points (0, 3, 7, 14 days after application) duplicate soil samples along with their traps

141

were sampled, processed and taken for chemical analysis (See section 2.6 and 2.7).

142

2.4.2.

143

A biometer type closed test setup was designed consisting of a 500 mL bottle with 50 g soil

144

(dW), 0.5 g tenax (for absorbing the volatiles) and 4 g of soda lime (for absorbing 14CO2). The

145

flask was closed using a stainless steel, plastic-free lock system (Swagelok connections, Hamlet

146

valves and fitting) (see Figure S2). The test was conducted exemplarily with just one soil (02-

147

A) in duplicates. The test chemical application and sample incubation were done as described

Flow-through setup (OECD 307) with volatiles combustion

Closed flask test setup 1

ACS Paragon Plus Environment

Environmental Science & Technology

148

in section 2.3, incubation period was 14 days. At each sampling date, the air in the headspace

149

was stripped out of the sample bottles through the tenax and was passed through 2N NaOH and

150

ethylene glycol traps using a vacuum pump. The soil sample, traps and the tenax was taken for

151

further analysis (See section 2.6 and 2.7).

152

2.4.3.

153

Unlike test setup 1, this new test setup comprised of a smaller test vessel 100 mL flask, instead

154

of 500 mL to lower the headspace volume and the soda lime was replaced with 6 mL of 2N

155

NaOH. Instead of self-prepared tenax inserts a tenax-adsorption tube (CAT no. 226-35 SKC

156

Inc.) was permanently connected to the flask in order to passively trap the volatilized fraction.

157

The same stainless steel, plastic free lock systems used in setup 1 were used to completely close

158

the test setup. The test chemical application and sample incubation were done as described in

159

section 2.3 and samples were taken in duplicates at 0, 7 and 14 days.

Closed flask test setup 2

Figure 1. Closed flask incubation test setup 2 used for testing the biodegradation of 14C labelled tetralin and decane in soil using guideline OECD 307. The test design consisted of 100 mL glass flask with 50 g (dm) soil with an internal CO2 absorbing flask and a permanently hanging tenax tube for passively trapping the volatile fraction. The entire test design was closed using a plastic free stainless steel lock system.

ACS Paragon Plus Environment

Page 10 of 31

Page 11 of 31

Environmental Science & Technology

160

Additionally, two reference samples in duplicates (See section S5) were prepared according to

161

test setup 2, without the tenax and NaOH flask but instead including an oxygen sensor spot

162

(“Redflash technology”, Pyroscience) attached to the inner wall of the test vessel in the

163

headspace. One of these references samples were applied with the same amount of co-solvent

164

without test chemical as in the test samples applied with 14C tetralin, whereas the other reference

165

sample was incubated under test conditions without solvent application. Every 2-3 days the

166

oxygen saturation in the headspace of these reference samples was measured with a Fiber optic

167

oxygen meter (Firesting O2, Pyroscience) without the need to open the vessel (For details see

168

SI section S7). In case the oxygen concentration in the headspace was found 5% of the applied radioactivity (aR) were taken for specific

213

chemical analysis. The extracts were centrifuged at 12300G for 5 min in 2 mL vial (Eppendorf

214

Germany) using a mini centrifuge (Microstar 12, VWR). The supernatant was taken for specific

215

chemical analysis using radio-HPLC. The tenax extracts were analysed without any clean-up

216

using radio-HPLC.

217

2.7.1

Radio-HPLC

218

For radio-HPLC analysis a Dionex Ultimate 3000 was used coupled with a UV detector (PDA-

219

100 photodiode Array detector) and a

220

separation was achieved by a Luna C18 (2) 3 μm 150 x 2 mm (MZ) column (Phenomenex,

221

Germany), with the column temperature maintained at 30°C. (For details on radio-HPLC

222

method used see SI section S11)

223

14C

detector (Ramona Raytest). The chromatographic

2.8 Data treatment

224

The starting point for fitting the degradation data was the degradation kinetics recommended

225

by FOCUS (FOrum for the Coordination of pesticide fate models and their USe)15. FOCUS

226

has developed various guidance documents originally to be used in pesticide registration.

227

However, many documents were later adopted by other regulations e.g., for biocides or

228

veterinary compounds. FOCUS recommended a single first order (SFO = Single First Order)

229

together with three different biphasic kinetic models (DFOP = Double First Order in Parallel,

230

HS: Hockey Stick and FOMC = First Order Multi Compartment). The fitting of the ACS Paragon Plus Environment

Environmental Science & Technology

231

experimental residues was done with using the software CAKE version 3.2 running on R

232

version 3.0.0. CAKE is a freely available software tool, which completely follows the

233

recommendations of FOCUS (2006/2014).

234

The recommendation for this type of data treatment is given for studies where volatilization is

235

not a significant process. Thus, in order to address the processes in these studies adequately,

236

the volatilization losses were considered as an additional product that neitherdecline nor

237

repartition into the soil. The volatilization is thus treated as a separate sink for the parent

238

compound, rather than as a partitioning process that can bring the parent compound back into

239

the soil11. The volatilization loss was considered to occur in parallel to the biodegradation.

240

Therefore, in this extended model the degradation and the volatilization of the compound were

241

considered as two processes and separated so that individual rate constants could be calculated

242

for the volatilization process as well as the degradation process. The calculation of DegT50 and

243

DegT90 values was based on the fraction of radioactivity in extracts, which could be identified

244

as parent substance. In general, the model assumes first order kinetics with k as an overall

245

dissipation rate and c the concentration of test chemical according to following equation: dc = - kc dt

246

(1)

247

However, for the extended model it is assumed that k consists of two rate constants kV

248

(volatilization rate) and kTt (transformation rate).

249

(2)

k = kT + kV

250

To describe the ratio of the two parallel processes the model internally uses “fractions”

251

FV(volatilization fraction) and FT (transformation fraction) which can be calculated based on

252

the individual rates for volatilization and transformation together with the overall decline rate

253

as follows:

254

FT =

kT k

( 3a)

FV =

kV k

(3b)

ACS Paragon Plus Environment

Page 14 of 31

Page 15 of 31

Environmental Science & Technology

255

For the structure of the standard and the extended model see Figure S12-13.

256

3. Results and Discussion

257

3.1. Pre-tests

258

The results from the biodegradation tests carried out with 14C tetralin using different test setups

259

after a 14 day incubation period in 02-A soil is shown in Figure S3. An incomplete mass balance

260

was obtained for the soil degradation test carried out in a flow-through setup despite using a

261

combustion oven to trap the volatile fraction in the form of completely oxidised 14CO2. This

262

suggested that the volatilized fraction was either escaping or being adsorbed to the fittings used

263

to connect the flow-through setup.

264

modification could not be utilised to attain a complete mass balance, which is a validation

265

criteria for the test. In contrast, a complete mass balance was obtained using test setup 1.

266

Nevertheless, the test setup was still considered inappropriate as 98% of the applied

267

radioactivity was volatilized and trapped in the tenax and thus unavailable for microorganism

268

in the soil. This made biodegradation measurements impossible, which is the primary goal of

269

the test. Additionally, the soda lime used as internal

270

considered impractical for direct analysis of mineralization as it had to be ground and taken for

271

combustion for radioactive analysis. The high amount of radioactivity in the tenax was

272

attributed to a higher headspace volume of the sample bottle, a higher amount of tenax filled in

273

the inserts, its dimensions and position within the sample bottle. A higher headspace volume

274

will result in a greater mass fraction of the test substance partitioning into the headspace10,11,

275

which could subsequently be trapped in the tenax thus making it unavailable for degradation.

276

Considering these factors, a test using setup 2 with smaller headspace, a different type and

277

positioning of the tenax absorber, NaOH as CO2 absorber and with regular oxygen monitoring

278

was performed. The results observed using test setup 2 displayed a complete mass balance with

279

only 20% of the applied radioactivity trapped on the tenax. Setup 2 was therefore considered

Therefore, the flow-through setup even with this

14CO

2

ACS Paragon Plus Environment

trap in the test setup 1 was also

Environmental Science & Technology

280

operationally superior to setup 1, as it would permit measurement of biodegradation with less

281

volatile losses. These results reveal the relevance of headspace and amount, dimensions and

282

position of tenax in a closed test setup for the distribution and the fate of a volatile chemical in

283

the test system.

284

3.2. Main test

285

3.2.1.

286

Figure 2 shows the oxygen saturation in the headspace of the reference samples of test setup 2

287

during the initial 28 days of the tetralin main study. The results showed almost no oxygen

288

depletion in the samples applied without co-solvent during the incubation period. In contrast,

289

for soil samples applied with co-solvent, different oxygen depletion trends were observed, with

290

the organic carbon rich silty loam (03-G) showing the most rapid oxygen depletion relative to

291

the other soils. In general, rapid depletion of oxygen saturation took place between day 0 and

292

14 in all soil samples applied with co-solvent. If the oxygen saturation measured was below

293

15% the samples were re-oxygenated with oxygen rich air to 18-20% saturation. Despite of

294

oxygenation every 2-3 days, continuous depletion of oxygen saturation was observed between

295

day 0 and 14 for all soils. This oxygen depletion could be attributed to the oxygen consumption

296

due to the degradation of the co-solvent.

297

These results suggest that the conditions in a closed biometer test setup can rapidly turn

298

anaerobic without regular oxygen supply, if a co-solvent is not evaporated after the application

299

of the test chemical. In all cases where the co-solvent can be evaporated without extensive

300

losses of test chemical this is therefore preferable. In cases where test chemical losses are too

301

high, and co-solvents cannot be avoided, such as when testing highly volatile chemicals,

302

changes from aerobic to anaerobic test conditions may influence the degradation kinetics due

303

to effects on the microbial communities. Therefore, we strongly recommend monitoring the O2

Oxygen monitoring in reference samples

ACS Paragon Plus Environment

Page 16 of 31

Page 17 of 31

Environmental Science & Technology

304

saturation during tests conducted in a closed biometer test setup if no evaporation of co-solvent

305

is performed. If the O2 saturation drops, supplement of additional oxygen is needed.

Figure 2 Oxygen saturation in the headspace of the reference samples for all four soils during the tetralin main study using test setup 2. Two reference samples were used, one being applied with and the other without solvent. The samples applied with solvent were oxygenated when oxygen saturation was < 15%, continuous depletion in the oxygen saturation was observed between 0-14 days. The oxygen measurements were done without the need to open the test vessel using an optical oxygen meter (Firesting, Pyroscience). 306

Mass balance

307

3.2.2.

308

In line with the results observed in the preliminary tests, the average overall observed recovery

309

was 99.9% ± SD of 10.6 (N=90) for decane and 104.8% ± SD of 5.5 (N=90) for tetralin in these

310

studies. A mass balance of 100 ± 15% was observed in 88.9% (N=90), and 100% (N=90) of the

311

test samples for decane and tetralin, respectively. Thus results from the main study confirm ACS Paragon Plus Environment

Environmental Science & Technology

312

that the test setup and approach that was developed to test volatile chemicals was highly

313

effective and reproducible in terms of obtaining a complete mass balance. The complete

314

degradation time series for all soil types for both test chemicals from the main study are shown

315

in Figure S8-11.

316

3.2.3.

317

Figure 3 shows the mineralization of tetralin and decane, measured in the CO2 traps, the

318

volatilization, measured in the tenax tubes, and the NER formation, measured as residues in the

319

soil after extraction. The 03-G and 02-A soils showed faster mineralization of tetralin than the

320

other two soils. In particular, very rapid mineralization of tetralin was observed for the 03-G

321

soil, in spite of the higher OC content in this soil compared to soil 01-A and 02-A. Slightly

322

faster mineralization of decane was also observed in the 03-G soil. The higher mineralization

323

rates in the 03-G soil can be explained by a combination of two factors. Firstly, the 03-G soil

324

had a higher amount of microbial biomass (See Table S6 and S7), and a higher microbial

325

activity as revealed by the higher oxygen depletion in the reference samples of this soil (Figure

326

2). Secondly, the volatilization was reduced due to the higher OC content, relative to the other

327

soils, leading to a higher fraction of test substance remaining in the soil available for

328

degradation.

Competing processes (sorption, volatilization and degradation)

ACS Paragon Plus Environment

Page 18 of 31

Page 19 of 31

Environmental Science & Technology

Figure 3 Volatilization, Mineralization and NER formation of tetralin (left) and decane (right) in four different soils (See Section 2.2). Volatilization, Mineralization, and NER were calculated as a percentage of the initial applied radioactivity (%aR). The figure shows that volatilization is higher for low OC content soils (01-A, 02-A) in comparison to the high OC soils (03-G, 04-A). In contrast, fastest mineralization and NER formation was observed in 03G soil with the highest OC content. 329

The radioactivity trapped in the tenax in both sterile and non-sterile samples was identified as

330

100% parent compound from the specific chemicals analysis data. As it can be observed in

331

Figure 3, a higher amount of test chemical was observed in the tenax for the soils with lower

332

OC relative to the soils with a higher OC suggesting greater volatilization from soils with lower

333

OC content. In the sterile samples containing tetralin and decane, the amount of test chemical

334

trapped in the tenax was also higher in the soils with lower OC carbon content (See Table S4).

335

These results illustrate how sorption of the test chemical to organic matter in the soil reduces

ACS Paragon Plus Environment

Environmental Science & Technology

336

its volatilization19-23 and, with the extended residence time, extent of biodegradation improves

337

in a closed flask test setup.

338

The results show that the volatilized fraction of the test chemical gradually or rapidly increased

339

and reached a plateau (see Figure 3). No considerable drop in the volatilized fraction was

340

observed along the incubation period. Slight drops observed at some sampling points might

341

have been due to the effect of overall lowered radioactivity recovery. This confirmed that in

342

our closed incubation test setup, the volatilized fraction was not re-mobilized and the tenax

343

traps acted as intended, as a contaminant sink24,10 rather than a partitioning reservoir25,11.

344

Although the KH value of decane is much higher than that of tetralin, the final fraction of

345

volatilized decane at the test end was slightly lower than for tetralin. However, for the sterile

346

samples the distribution into the tenax was in line with the KH values (Table S4). These

347

differences in mass distribution can be explained by the faster degradation rate of decane in the

348

non-sterile samples relative to its volatilization rate. Furthermore, decane has a higher Koc value

349

which improves its sorption to the organic fraction of the soil.

350

A considerable portion of the applied radioactivity was recovered as NER in both the tetralin

351

and decane studies. The rate of NER formation was faster and higher for decane compared to

352

tetralin. Similar to the mineralization, highest and rapid NER formation was observed in the

353

03-G soil for tetralin, whereas in the decane study the NER formation and mineralization at the

354

end of study was more or less the same in all the soils. Studies on NER26-28 suggest that the

355

formation of bio-NER is linked to mineralization. This is also apparent in our study. Recently

356

a microbial to biomass turnover (MTB) method was developed for predicting the fraction of

357

bio-NER29-30. This MTB method was applied using required inputs from our test and literature

358

data to predict the bio-NER fraction (see Table S8). The short term bio-NER prediction was

359

done exemplarily until 28 days for tetralin and until end of the test (12d for soil 01A, 02A and

360

04A and 7d for soil 03G) for decane. The results showed that the predicted bio-NER was higher ACS Paragon Plus Environment

Page 20 of 31

Page 21 of 31

Environmental Science & Technology

361

than the total NER observed in the test by a factor of 1.19-1.77 for decane whereas for tetralin

362

it was slightly lower by a factor 0.65-0.77 (for details see Table S9). Thus, MTB method also

363

indicates high bio-NER formation for these test chemicals. This argument was also supported

364

by the results observed in the sterile sample where almost no NER formation was observed (