Catalytic Pyrolysis of Waste Polyethylene into Aromatics by H3PO4

5 days ago - E; Energy & Fuels · Environmental Science & Technology .... The content of aromatics increased along with the residence time, and could b...
1 downloads 0 Views 7MB Size
Subscriber access provided by University of South Dakota

Catalysis and Kinetics

Catalytic Pyrolysis of Waste Polyethylene into Aromatics by H3PO4-activated Carbon Kai Sun, Qunxing Huang, Xiangdong Meng, Yong Chi, and Jianhua Yan Energy Fuels, Just Accepted Manuscript • DOI: 10.1021/acs.energyfuels.8b02091 • Publication Date (Web): 27 Aug 2018 Downloaded from http://pubs.acs.org on September 1, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

1 2

Catalytic Pyrolysis of Waste Polyethylene into Aromatics by H3PO4-activated Carbon

3

Kai Sun, Qunxing Huang*, Xiangdong Meng, Yong Chi, Jianhua Yan

4

State Key Laboratory of Clean Energy Utilization, Zhejiang University, Hangzhou310027,

5

People’s Republic of China

6

KEYWORDS: polyethylene; catalytic pyrolysis, oil, aromatics, H3PO4

7

ABSTRACT: H3PO4-activated carbon was used as the catalyst in the pyrolysis of waste

8

polyethylene (PE) to study its catalytic effect on the enrichment of the aromatics. The effect

9

of the mass fraction ratio of phosphorus to wood chips (defined as the P/WC ratio) during

10

impregnation and the residence time of the catalytic reaction on the product yield and the oil

11

components were investigated and the catalytic mechanism was discussed. The increase of

12

the P/WC ratio from 10 to 50% and the residence time from 1 to 5 s would increase the oil

13

yield from 23.2 to 41.8% and 40.8%, respectively. Alkanes, alkenes and aromatics were the

14

main components in the oils. The content of aromatics increased along with the residence

15

time, and could be up to 30.0% when the P/WC ratio was 40%. Monocyclic aromatics,

16

mainly alkyl and alkenyl benzenes with carbon atom numbers between 7 and 10 were the

17

main aromatic compositions, the highest content of which was up to 23.8% when the P/WC

18

ratio was 40% and the residence time was 3s. High P/WC ratio would accelerate the

19

conversion of isomerized products to aromatized ones. The hydrogen transfer reactions 1 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 2 of 48

20

catalyzed by Brønsted acid sites such as P-OH in C-O-PO3, C2-PO2, and C-PO3, and the

21

direct dehydrogenation catalyzed by dehydrogenation active sites like P=O were the main

22

aromatization processes.

23

1. Introduction

24

Nowadays, due to the characteristics of lightweight, easy-processing, and low-cost,

25

plastics have been widely used in numerous sectors, such as construction, automotive,

26

manufacturing, and medical.1, 2 It is reported that the production of plastics in the whole

27

world has reached 322 million tons in 2015.3 The expanding demand for plastics products has

28

provoked the production of large quantities of waste plastics, which has led to serious

29

environmental and social problems4 due to their short life span and non-biodegradability.5-7

30

Among all the polymers, polyethylene (PE) is the main components of waste plastics, which

31

accounted for around 40% of the waste plastics.8 To date, mechanical recycling, landfill, and

32

combustion are still the first options for waste plastics treatment,6 which are either costly and

33

complicated, or detrimental to environment, or energy-wasting.9-11 Compared with these

34

conventional disposal methods, pyrolysis, especially catalytic pyrolysis, has become a

35

promising energy-recovery method for the conversion of waste plastics like PE to high

36

value-added products, such as aromatics. 3, 10, 11

37

Commonly used catalysts in the pyrolysis of plastics are mainly (metal impregnated)

38

zeolite catalysts, transition metal catalysts, and conventional acid or alkaline solids,12,

13

39

which could reduce the energy consumption, change the products distribution, and improve

40

the oil quality.14-16 Marcilla et al.17 found that the content of aromatics in the oil could be up 2 ACS Paragon Plus Environment

Page 3 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

41

to 52.1% by HZSM-5 in the catalytic pyrolysis of LDPE at 500 °C. However, the oil yield

42

was only 18.3%. Elordi et al.18 found that using HY zeolites in the pyrolysis of HDPE in a

43

conical spouted bed reactor at 500 °C could increase the oil yield to around 72.6%, while the

44

content of aromatics in oil was just around 24.1%. Aguado et al.2 comparatively studied the

45

catalytic pyrolysis of LDPE by mesostructured zeolites Al-MCM-41, and found that the oil

46

yield could reach 42 % compared with 26% achieved by HZSM-5 while the aromatic yield

47

was only 4% in the gasoline fraction. Elordi et al.19 obtained an oil yield as high as 61.6%

48

when spent FCC was used as the catalyst in the pyrolysis of HDPE at 500 °C, while the

49

aromatics only accounted for 11.8% of the gasoline fraction. Mosio-Mosiewski et al.20

50

obtained an oil yield of 64.6% and an aromatic yield of 18.3% using amorphous acid

51

aluminosilicate catalyst in the high pressure (10Mpa) catalytic cracking of PE at 420 °C.

52

Renzini et al.21 found that the content of aromatics in the cracking oil of PE catalyzed by

53

Zn-ZSM-11 at 500 °C could be up to 53.0% and the oil yield could reach 55.1%. Uemichi et

54

al.22, 23 obtained a high content of aromatics which could be up to 46.2 and 30% when using

55

Pt-activated carbon in the catalytic pyrolysis of PE and PP, respectively. However,

56

serious-coking and high-cost limit the promotion of these transition metal catalysts.

57

Nowadays, cost-efficient carbon-based catalysts are gaining attention due to their

58

low-cost, controllable pore size, and adjustable surface properties.11 The chemical activated

59

carbon was one of the cheap and widely used carbonaceous materials which was endowed

60

with catalytic activities due to the surface modification of activating agents like H3PO4. The

61

H3PO4-activated carbon has been used as the catalyst for the oxygen reduction reaction in the

62

air-cathode microbial fuel cells,24 the selective dimerization of isobutene,25 and the catalytic

63

fast pyrolysis of cellulose and biomass,

64

H3PO4-activated carbon as the catalyst in the pyrolysis of plastics and production of

26

etc. But as far as we know, few researchers used

3 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

65

aromatics.

66

In our previous work, the catalytic effect of H3PO4-activated carbon to the pyrolysis oil

67

of mixed plastics (PE, PP and PS) was investigated and it showed high selectivity towards

68

aromatics (66.0%).11 However, the main factors affecting the catalytic process and the

69

reaction mechanisms haven’t been discussed detailedly. In this study, only the waste PE was

70

chosen as the feedstock to avoid the influence of the interaction among different plastic

71

components. The effect of the impregnation ratio in activation and the residence time in

72

catalytic reaction to the oil quality were analyzed, and the role of the catalytic active sites

73

were discussed, which could provide a better understanding of the catalytic behavior of

74

H3PO4-activated carbon in the pyrolysis of plastics.

75

2. Materials and Methods

76

2.1. Materials

77

Polyethylene (PE) powder was purchased from Guanbu Electromechanical Technology

78

Company (Shanghai, China). After being received, it was dried and sieved to a particle size of

79

smaller than 0.18 µm.

80

Catalysts used in this work were activated carbons prepared by chemical activation

81

methods. The H3PO4-activated carbon (P-AC) was prepared by impregnating wood chips by

82

H3PO4 solution for 24h. The mass fraction ratios of P to wood chips (abbreviated as P/WC

83

ratio) were 10, 20, 30, 40, and 50%, respectively. After impregnation, the mixtures were dried

84

and calcined from 50 to 600 °C under nitrogen flow at a heating rate of 10°C/min and with a 4 ACS Paragon Plus Environment

Page 4 of 48

Page 5 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

85

dwell time of 90 min. After being cooled, they were washed, dried and ground to 80-200

86

mesh. These catalysts were marked as P-AC-10% - 50% according to the different P

87

concentrations in the impregnating solution correspondingly.

88

In order to figure out the action mechanism of H3PO4, HNO3 and other typical

89

phosphorus compounds such as (NH4)2HPO4 were also used as the impregnating agents to

90

prepare activated carbon (abbreviated as HNO3-AC, (NH4)2HPO4-AC, respectively). The

91

HNO3 solution used to prepare HNO3-AC had the same pH with the H3PO4 solution used to

92

prepare P-AC-30%. While the (NH4)2HPO4 solution had the same P/WC ratio with

93

P-AC-30%.

94

2.2. Experimental Setup and Product Analysis

95

The catalytic pyrolysis of PE was carried out on a two staged fixed bed reactor equipped

96

with a temperature-programmed device. The quartz boat with 10 g of PE sample in it was

97

placed at the first stage, while a mixture of 4 g of catalysts and quartz sand was loaded at the

98

second stage and supported by the silica wool. The first stage was heated from 50 to 550 °C

99

at a heating rate of 20 °C/min and with a dwell time of 60 min, while the second stage was

100

kept at a constant temperature of 600 °C. The residence time was determined by the flow rate

101

of the nitrogen, which was defined as Eq. (1)

102

103

Residencetime =

Vc × Ta × 60 FN 2 × Tc

(1)

where  is the volume of the mixture of catalyst and quartz sand, dm3; is the gas 5 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 6 of 48

104

flow rate of nitrogen at ambient temperature, L/min;  is the ambient temperature, K;  is

105

the catalytic temperature, K.

106

By calculation, 0.518, 0.258, 0.173, 0.129, and 0.104 L/min at ambient temperature

107

corresponded to 1.0, 2.0, 3.0, 4.0, and 5.0 s, respectively. The addition of quartz sand was to

108

ensure the consistency of the mixture volume, thus when the gas flow rate was constant, the

109

residence times among different groups could maintain the same. The schematic diagram

110

illustrating the principle of the catalytic pyrolysis is shown in Fig. 1.

111

The pyrolytic vapors were cooled down and collected by three gas washing bottles filled

112

with dichloromethane. The circulating water was used to keep the gas washing bottles cold.

113

After reaction, the dichloromethane solution of oil in gas washing bottles was dried at 40 °C

114

and weighted, which was considered to be the mass of the oil product. The mass differences

115

of the quartz boat and the second stage were considered to be the mass of the solid residues

116

and the coke on the catalysts, respectively. The gas yield was calculated by mass balance. Gas

117

chromatography-mass spectrometry (GC-MS, Agilent 6890-5973, USA) with a DB-5 column

118

was used to analyze the main 40 - 50 compositions of the oil product. The oven was held at

119

80 °C for 2 min, then heated to 250 °C at a rate of 20 °C/min, and kept for 10 min for each

120

test. Semi-quantitative analysis was used to calculate the selectivities of the oil compositions

121

based on the peak areas in the chromatogram, and the content was expressed by area %.

122

A scanning electron microscopy coupled with energy-dispersive spectroscopy

123

(SEM-EDS, SIRON, FEI, Holland) was used to characterize the surface morphology and

124

actual P content on the surface of the catalysts. 6 ACS Paragon Plus Environment

Page 7 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

125

An automatic specific surface and micropore size analyzer (AUTOSORB-IQ2-MP,

126

Quantachrome, USA) was used to measure the specific surface area and the pore size

127

distribution of the catalysts. The specific surface area was calculated by multiple Brunauer–

128

Emmett–Teller (BET) method. The information of micropore and mesopore was obtained by

129

HK and BJH method, respectively.

130

The surface chemical structure of the catalysts was recorded by an X-ray photoelectron

131

spectrophotometer (XPS, VG ESCALAB MKII, VC, UK). High-resolution spectra of P 2p

132

was recorded using Non-monochromatic Mg Kα X radiations (hγ=1253.6 eV) and

133

curve-fitted by multiple Gaussian function.

134

3. Results and discussion

135

3.1. Characteristics of the Catalysts.

136

The SEM pictures of the catalysts P-AC-10% - 50% are shown in Fig. 2. It could be

137

seen that no apparent pores were formed on the surface of P-AC-10% and P-AC-20%. When

138

P concentration in impregnating solution was high than 30%, the activation effect of

139

phosphoric acid formed developed pore structures on the carbon surfaces. P-AC-40% had the

140

most developed cylindrical pores along the woody fibers. It could also be seen that the pores

141

of P-AC-50% were apparently blocked probably because of the phosphorus pentoxide formed

142

by the decomposition of excessive phosphoric acid and the collapsed pore walls.

143

The specific surface area and the pore properties of the P-ACs and the P content on the

144

catalyst surfaces are listed in Table 1. P content on the catalysts increased along with the 7 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

145

concentration of impregnating solution, which could reached 25 wt% when the P/WC ratio

146

was 50%. The maximum BET surface area and total pore volumn could be up to 742.9 m2/g

147

and 0.860 cm3/g, respectively, when the P/WC ratio reached 40%. The average pore size of

148

P-AC-40% was 5.00 nm, which indicated that it was a developed mesoporous activated

149

carbon. When the P/WC ratio continued to grow, the specific surface area and the total pore

150

volume decreased, which was caused by the blockage showed in Fig. 2(e). While the increase

151

of the average pore diameter from 5.00 to 5.79 nm indicated that there may be the collapse of

152

the pore walls and the merge of the small pores.

153

3.2. Properties of the Oil Product at different P/WC Ratios

154

The product yields of the groups with different P/WC ratios and the same residence time

155

(Group 0# -5#) were listed in Table 2. The mass of the solid residue derived from PE

156

pyrolyzed at 550 °C could be negligible. The quartz sand was considered to be a reference

157

material in the non-catalytic pyrolysis group. It could be observed that the gas was the main

158

products while the oil yield was only 23.2% in the non-catalytic pyrolysis group (0#). The

159

slight weight increment of quartz sand was probably due to the attachment of the heavy

160

long-chain hydrocarbons on its surface. When the catalysts were used, the oil and coke yield

161

increased with the P/WC ratio, which was probably due to the polycondensation of light

162

hydrocarbons into heavier molecules with higher solubility in dichloromethane,27 and the

163

further condensation of large molecules (such as polyaromatics) into coke catalyzed by acid

164

sites.

165

The components of oil products catalyzed by P-ACs with different P/WC ratios are 8 ACS Paragon Plus Environment

Page 8 of 48

Page 9 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

166

shown in Fig. 3(a). The main components in the oil products were alkanes, alkenes, and

167

aromatics. The non-catalytic pyrolysis yield 74.4% alkenes (including monoenes and dienes)

168

and 24.1% alkanes with a wide boiling point range.28 The addition of P-AC significantly

169

increased the content of aromatics and decreased the alkene yield. When the P/WC ratio was

170

below 20%, aromatization process was not obvious. The content of alkenes only decreased

171

slightly probably due to the dehydrogenation reaction catalyzed by the dehydrogenation sites

172

such as C=O and P=O,29 and a small amount of aromatics were thus formed. When the P/WC

173

ratio reached 30%, the content of alkanes and aromatics significantly increased at the cost of

174

a great quantity of alkenes. That was due to the hydrogen transfer reactions of alkenes which

175

yielded H-rich materials like alkanes and H-deficient materials like aromatics.30 The

176

increasing number of acid sites could enhance the transformation of alkenes to carbonium

177

ions, which provided large quantities of feedstocks for the secondary reactions such as

178

hydrogen transfer reaction. This was detailedly explained in Fig. 9. When the P/WC ratio

179

continued to grow, the content of alkenes was no longer significantly reduced. The content of

180

alkanes in group 4# catalyzed by P-AC-40% decreased to 24.6% and the content of aromatics

181

reached 30.0%. This was due to the promotion of dehydrogenation which converted alkenes

182

to aromatics and alkanes to both alkenes and aromatics. This process was catalyzed by the

183

increasing number of dehydrogenation active sites like P=O caused by the increasing

184

concentration of the impregnating solution, and the detailed catalytic mechanisms are shown

185

in Fig. 9. The components of the oil in group 5# were similar to group 4#. The aromatic yield

186

was slightly decreased owing to the decline of the catalytic efficiency. The decreased specific

187

surface area caused by the blockage and merge of the pores would reduce the number of the 9 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

188

Page 10 of 48

acid sites on the catalyst surface, which led to the decline of the catalytic efficiency.

189

The isomerization and aromatization degrees of the main oil components are shown in

190

Fig. 4(a). It could be concluded that the total content of isomerized and aromatized products

191

increased along with the P/WC ratio in general. When the P/WC ratio was lower than 20%,

192

the growth of isomerization products was much faster than that of aromatized products.

193

However, when the P/WC ratio was higher than 30%, the content of aromatized products

194

significantly increased, while the content of isomerized products gradually decreased. When

195

P/WC ratio was higher than 40%, the reduction of catalytic efficiency caused by the decrease

196

of the specific surface area started to inhibit the aromatization reaction. However, the further

197

decrease in the content of isomerized products was still remarkable, which was because the

198

surface acidity was still strong enough for the transformation of isomerized products to

199

aromatized ones.

200

It was believed that the catalytic pyrolysis of PE by solid acid catalysts followed the

201

carbocation mechanism.31, 32 The straight-chain hydrocarbons (such as normal alkanes and

202

1-alkenes) derived from the thermal pyrolysis of PE formed secondary carbenium ions on the

203

acid sites firstly, which could either form stable tertiary carbenium ions, and then formed the

204

isomerized products, or crack into smaller alkenes and formed new carbenium ions by

205

β-scission.33, 34 When the P/WC ratio was relatively low, the increase in the number of the

206

acid sites and the dehydrogenation active sites accelerated the formation of carbenium ions,

207

which led to the promotion of isomerization reaction and β-scission. While the impregnation

208

by higher concentration of H3PO4 increased the acidity and the number of the acid sites on 10 ACS Paragon Plus Environment

Page 11 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

209

P-AC, which promoted the aromatization activity, such as the hydrogen transfer reactions and

210

dehydrogenation of the already formed carbenium ions. Thus, a large quantity of aromatics

211

formed at the cost of tertiary carbenium ions, leading to the reduction in the content of the

212

isomerized products.

213

The GC-MS chromatograms of the oil products catalyzed by the P-AC under different

214

P/WC ratios were exhibited in Fig. 5(a). It could be seen that C7 – C23 components were the

215

main components in the catalytic pyrolysis oils for all groups. With the increase of the P/WC

216

ratio, the retention time of the peak with high intensity gradually decreased, which indicated

217

that the oil products were getting lighter. This was probably due to the scission of long-chain

218

hydrocarbons into shorter ones enhanced by the increase in the number of the acid sites. The

219

number and intensities of the peaks representing aromatics increased along with the

220

impregnation concentration of P. The presence of aromatic 10, 13, 15, and 22 showed the

221

trend of dehydrocyclization during aromatization process, which appeared in all groups.

222

While aromatic 11, 20, 21 were probably derived from the aromatization of the isomerized

223

products, which did not appear until the P/WC ratio was higher than 30%. This also proved

224

that the strong surface acidity and high P concentration promoted the transfer of isomerized

225

products to aromatized ones.

226

The effect of different P/WC ratios on the aromatic compositions classified by the

227

number of aromatic rings are shown in Fig. 6(a). The content of main aromatic compositions

228

is listed in Table S1. Monocyclic aromatic hydrocarbons (MAHs) were the dominant

229

components in aromatics for all groups, followed by bicyclic aromatic hydrocarbons (BAHs) 11 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 12 of 48

230

and a small amount of tricyclic aromatic hydrocarbons (TAHs). MAHs were mainly alkyl and

231

alkenyl benzenes with carbon atom numbers between 7 and 10. BAHs were mainly

232

naphthalenes and a small amount of biphenyl. The fused-ring aromatics such as anthracene

233

and penanthrene were the main compositions of TAHs. The branches on MAHs and BAHs

234

may be formed by both the cyclization of the long-chain carbonium ions and the alkylation of

235

the already formed aromatics catalyzed by the acid sites.35, 36 Acid sites were effective in

236

transforming alkanes or alkenes into long-chain carbonium ions and aromatics into

237

arylcarbenium ions, which were the feedstocks in the cyclization and alkylation reaction,

238

respectively. For the MAHs, the content increased along with the P/WC ratio and reached the

239

peak (23.78%) when the P/WC ratio was around 40%. After that the content of MAHs

240

decreased to 17.97%, which was due to the promoted condensation reaction of the MAHs

241

into polycyclic aromatics catalyzed by the strong acid sites. Aromatics like MAHs could form

242

arylcarbenium ions on Brønsted acid sites, which could yield polyaromatics by continuous

243

dehydrogenation and condensation reaction. For the BAHs and TAHs, the content also

244

increased as the P/WC ratio increased but with a much lower growth rate compared with

245

MAHs. What’s more, when the P/WC ratio was lower than 30%, there were no TAHs

246

detected. Considering the selectivities toward different aromatic compositions, a P/WC ratio

247

of 40% was appropriate for the production of aromatics, especially MAHs.

248

3.3. Properties of the Oil Product under Different Residence Times

249

Group 3# and 6# - 9# in Table 1 exhibited the effect of different residence times on the

250

product yields. As the residence time increased, the oil yield and coke yield increased, which

12 ACS Paragon Plus Environment

Page 13 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

251

was due to the polymerization of the light products into heavier ones. When PE was catalyzed

252

by P-AC-30% with the residence time of 5 s (group 9#), the oil yield could be up to 40.8%,

253

which was similar to 41.8% obtained by group 5# catalyzed by P-AC-50% with the residence

254

time of 3 s. However, the coke yield in group 9# was only 59.4% of that in group 5#. This

255

indicated that prolonging residence time was more suitable and efficient in improving the

256

product quality.

257

The components of the oil products catalyzed by P-ACs under different residence times

258

are shown in Fig. 3(b). When the residence time was less than 2 s, the aromatization reaction

259

was slow and the main components in the oils were alkenes just like the oils catalyzed by

260

P-AC with low P/WC ratios. Hydrogen transfer reactions between alkenes firstly formed

261

H-deficient intermediates like dienes and cycloalkenes. Due to the limit of the number of the

262

acid sites, few intermediates could be converted into aromatics by further intermolecular

263

hydrogen transfer.37 During this stage, aromatics may be mainly formed by direct

264

dehydrogenation of alkanes and alkenes, which was catalyzed by the dehydrogenation active

265

sites. When the residence time was prolonged to 3 s, the content of alkanes and aromatics

266

increased at the cost of alkenes. The already formed H-deficient intermediates started to be

267

transformed to aromatics, and lots of alkanes were produced as the H-rich products. As the

268

residence time was prolonged from 3 s to 5 s, the consumption of H-deficient intermediates

269

weakened the aromatic produced from hydrogen transfer reactions. Direct dehydrogenation

270

of alkanes and alkenes led to the decrease of alkane content and the slight increase of

271

aromatic content. These parts of catalytic reaction mechanisms were summarized in Fig. 9.

272

Compared with using P-AC with high impregnation ratio, prolonging residence time was less 13 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

273

Page 14 of 48

efficient in increasing the yield of aromatics.

274

Fig. 4(b) showed the changes in the isomerization and aromatization degrees of the oil

275

products under different residence times. P-AC-30% provided a moderate acidity and an

276

appropriate number of acid sites, leading to the simultaneous increase in the content of both

277

isomerized and aromatized products (see Fig. 9). However, the conversion of isomerized

278

products to aromatized ones still existed, which could be proved by the slightly decreased in

279

the content of isomerized products at a residence time of 5 s.

280

The GC-MS chromatograms of the oil products obtained under different residence times

281

are exhibited in Fig. 5(b). As the residence time increased, the heavy long-chain

282

hydrocarbons were converted into lighter ones. The intensity of the peaks representing

283

aromatics was growing and the main aromatic species were similar to those in the oils

284

catalyzed by different P-ACs. From Fig. 6(b) and Table S2 it could be seen that the content of

285

MAHs was rapidly increased from 3.14% to 21.07% when the residence time was prolonged

286

from 1 s to 5 s. While for the BAHs, the content reached its peak (4.66%) when the residence

287

time was 3 s. After that, the content of BAHs gradually decreased with the increase of the

288

residence time. This was due to the condensation reaction of BAHs into heavier fused-ring

289

aromatics catalyzed by the strong acid sites, which was difficult to be collected and detected

290

by the GC-MS.

291

3.4. Discussion of the Catalytic Mechanism

292

P-AC-30% was used to study the effect of H3PO4 on PE conversion. Meanwhile 14 ACS Paragon Plus Environment

Page 15 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

293

(NH4)2PO4 and HNO3 were also used as the activating agents for comparative studies. The oil

294

components catalyzed by P-AC, (NH4)2PO4-AC, and HNO3-AC are shown in Fig. 7.

295

The oil obtained by the catalysis of (NH4)2PO4-AC had a higher content of alkenes and a

296

lower content of aromatics and alkanes, which were probably due to the weakened hydrogen

297

transfer reactions catalyzed by acid sites. The formation of acid sites was strongly related to

298

the properties of the impregnating solution. Compared with the strong acid impregnating

299

solution (pH=1.45) of P-AC-30%, the solution used for the impregnation of (NH4)2PO4-AC

300

was weakly alkaline (pH=8.4) which was detrimental to the formation of acid sites on the

301

activated carbon. Thus, aromatics may be mainly formed by the direct dehydrogenation

302

catalyzed by some dehydrogenation active sites. It could be confirmed that the hydrogen

303

transfer reactions catalyzed by acid sites was one of the important sources of aromatics, and

304

enough acidity of the impregnating solution was necessary.

305

The selectivity of HNO3-AC to aromatics was 16.8%, which was slight higher than that

306

of P-AC-30%. However, the content of other compositions, mainly nitrogenous and

307

oxygenated compounds was as high as 63.9 %, which would greatly reduce the quality of the

308

oil. These compounds were probably derived from the reactions between the feedstocks and

309

the unstable nitrogen- and oxygen-containing functional groups, which was formed during

310

the HNO3 impregnation. In comparison, phosphorus complexes formed during H3PO4

311

activation were insoluble and thermally stable at even 700 °C on the carbon surface,38, 39

312

which had little negative effect on the oil quality. Thus, H3PO4 was more suitable for the

313

production of acid catalyst compared with other common volatile acid. 15 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

314

Fig. 8 illustrates the high resolution P 2p spectra and the curve-fitting results.38, 40 It

315

could be seen that C3-PO was the main phosphorus-containing group, the content of which

316

was up to 51.5%, followed by C-O-PO3 (28.5%) and P2O5 (11.5%). P2O5 was produced from

317

the thermal decomposition of H3PO4 during the activation, the content of which has been

318

greatly reduced due to its vaporization above 580 °C.41

319

P-OH in C-O-PO3, C2-PO2, and C-PO3 may be the main Brønsted acid sites formed by

320

H3PO4 treatment.42 These acid active sites were responsible for the hydrogen transfer

321

reactions, cyclization and alkylation of the aromatics. Hydrogen transfer reaction was a main

322

source of aromatics. However, the production of aromatics through hydrogen transfer

323

reactions would inevitably yield a large quantity of alkanes, which inhibited the improvement

324

of the aromatic selectivity.43 It was reported that P=O played an important role in the catalytic

325

dehydrogenation reaction not only because it could enhance the dehydrogenation activity of

326

other active sites such as C=O, but also due to its ability to be independent active sites for

327

dehydrogenation.29 Thus, the direct dehydrogenation catalyzed by P=O in C-O-PO3, C2-PO2,

328

C-PO3 and C3-PO was another important way of aromatic formation which consumed both

329

alkanes and alkenes. The reaction mechanisms of catalytic aromatization are illustrated in Fig.

330

9.

331

4. Conclusion

332

H3PO4-activated carbon (P-AC) was used as the catalyst in the pyrolysis of PE carried

333

out in a two staged fixed bed reactor in order to study its effect on the aromatic enrichment in

334

pyrolysis oil. The effect of the P/WC ratio and residence time was investigated and the 16 ACS Paragon Plus Environment

Page 16 of 48

Page 17 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

335

catalytic mechanism was discussed. The main conclusions can be drawn as follows:

336

(1) The increase of the P/WC ratio (10 to 50%) and residence time (1 to 5 s) led to the

337

increase in the oil yield from 23.2% to 41.8% and 40.8%, respectively. However,

338

compared with prolonging residence time, increasing the P/WC ratio would lead to more

339

serious coking.

340

(2) The total content of the isomerized and aromatized products increased along with the

341

residence time and the P/WC ratio in general, while increasing the P/WC ratio would

342

accelerate the conversion of isomerized products to aromatized ones.

343

(3) The content of aromatics reached the peak (30.0%) when the P/WC ratio was 40%, while

344

the aromatic yield increased along with the residence time when it was between 1 s and 5

345

s. MAHs, such as alkyl and alkenyl benzenes with carbon atom numbers between 7 and

346

10, were the main components in aromatics, which could be up to 23.8% in the oil when

347

the P/WC ratio was 40% and the residence time was 3 s.

348

(4) H3PO4 treatment formed phosphorus-containing functional groups on the carbon surface,

349

which played a major catalytic role in the aromatic enrichment. The hydrogen transfer

350

reactions catalyzed by Brønsted acid sites such as P-OH in C-O-PO3, C2-PO2, and C-PO3,

351

and the direct dehydrogenation catalyzed by dehydrogenation active sites like P=O were

352

the main processes of aromatization.

353

17 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 18 of 48

354

Associated content

355

Supporting Information

356

The main aromatic compositions of the oils catalyzed by P-ACs with different P/WC ratios

357

(based on peak area). (Table S1)

358

The main aromatic compositions of the oils catalyzed by P-ACs with different residence

359

times (based on peak area). (Table S2)

360

Author information

361

Corresponding Author

362

*Telephone: +86-571-87952834. Fax: +86-571-87952438. E-mail: [email protected]

363

Notes

364

The authors declare no competing financial interest.

365

Acknowledgments

366

This work was supported by National Natural Science Foundation of China (Grant No.

367

51621005),

the

National

Key

Research

and

Development

Program

of

China

368

(2016YFE0202000), the Environmental Protection Special Funds for Public Welfare

369

(201509013) and the Fundamental Research Funds for the Central Universities.

370

18 ACS Paragon Plus Environment

Page 19 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

371

References

372

(1) Al-Salem, S. M.; Antelava, A.; Constantinou, A.; Manos, G.; Dutta, A., A review on

373

thermal and catalytic pyrolysis of plastic solid waste (PSW). Journal of environmental

374

management 2017, 197, 177-198.

375

(2) Aguado, J.; Serrano, D. P.; Miguel, G. S.; Castro, M. C.; Madrid, S., Feedstock recycling

376

of polyethylene in a two-step thermo-catalytic reaction system. Journal of Analytical &

377

Applied Pyrolysis 2007, 79, (1), 415-423.

378

(3) Man, V. S.; Kumar, S.; Sarker, M., Waste HD-PE Plastic Deformation into Liquid

379

Hydrocarbons as Fuel by a Pyrolysis-Catalytic Cracking Using the CuCO3 Catalyst.

380

Sustainable Energy & Fuels 2018.

381

(4) Lee, K. H., Composition of aromatic products in the catalytic degradation of the mixture

382

of waste polystyrene and high-density polyethylene using spent FCC catalyst. Polymer

383

Degradation & Stability 2008, 93, (7), 1284-1289.

384

(5) Sharuddin, S. D. A.; Abnisa, F.; Wan, M. A. W. D.; Aroua, M. K., A review on pyrolysis

385

of plastic wastes. Energy Conversion & Management 2016, 115, 308-326.

386

(6) Lopez, G.; Artetxe, M.; Amutio, M.; Bilbao, J.; Olazar, M., Thermochemical routes for

387

the valorization of waste polyolefinic plastics to produce fuels and chemicals. A review.

388

Renewable & Sustainable Energy Reviews 2017, 73, 346-368.

389

(7) Miandad, R.; Anjum, M.; Waqas, M.; Ahmad, I.; Alafif, Z. O. A.; Aburiazaiza, A. S.;

390

Barakat, E. F.; Akhtar, T., Solid waste management in Saudi Arabia: A review. Journal of the

391

Science of Food & Agriculture 2016, 1, (1), 13-26.

392

(8) Williams, P. T.; Williams, E. A., Fluidised bed pyrolysis of low density polyethylene to

393

produce petrochemical feedstock. Journal of Analytical & Applied Pyrolysis 1999, 51, (1–2),

394

107–126.

395

(9) Demirbas, A.; Al-Sasi, B. O.; Nizami, A. S., Conversion of waste tires to liquid products

396

via sodium carbonate catalytic pyrolysis. Energy Sources 2016, 38, (16), 2487-2493.

397

(10) P. N. S.; Lin†, Y. H.; A. A. G.; Dwyer, J., Investigation of the Catalytic Pyrolysis of

398

High-Density Polyethylene over a HZSM-5 Catalyst in a Laboratory Fluidized-Bed Reactor. 19 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 20 of 48

399

Industrial & Engineering Chemistry Research 1997, 36, (12), 5118-5124.

400

(11) Sun, K.; Huang, Q.; Ali, M.; Chi, Y.; Yan, J., Producing aromatic enriched oil from

401

mixed plastics using activated biochar as catalyst. Energy & Fuels 2018.

402

(12) Ratnasari, D. K.; Nahil, M. A.; Williams, P. T., Catalytic Pyrolysis of Waste Plastics

403

using Staged Catalysis for Production of Gasoline Range Hydrocarbon Oils. Journal of

404

Analytical & Applied Pyrolysis 2017, 124.

405

(13) Miandad, R.; Barakat, M. A.; Aburiazaiza, A. S.; Rehan, M.; Nizami, A. S., Catalytic

406

pyrolysis of plastic waste: A review. Process Safety and Environmental Protection 2016, 102,

407

822-838.

408

(14) Yu, W.; Que, H.; Zhou, Z.; Yang, J.; Fei, Q.; Yang, P., Online Study on the Pyrolysis of

409

Polypropylene over the HZSM-5 Zeolite with Photoionization Time-of-Flight Mass

410

Spectrometry. Energy & Fuels 2015, 29, (2), 150108210943001.

411

(15) Marcilla, A.; Beltran, M.; Conesa, J. A., Catalyst addition in polyethylene pyrolysis :

412

Thermogravimetric study. Journal of Analytical & Applied Pyrolysis 2001, s 58–59, (2),

413

117-126.

414

(16) Bagri, R.; Williams, P. T., Catalytic pyrolysis of polyethylene. Journal of Analytical &

415

Applied Pyrolysis 2002, 63, (1), 29-41.

416

(17) Marcilla, A.; Beltrán, M. I.; Navarro, R., Thermal and catalytic pyrolysis of polyethylene

417

over HZSM5 and HUSY zeolites in a batch reactor under dynamic conditions. Applied

418

Catalysis B Environmental 2009, 86, (1–2), 78-86.

419

(18) Elordi, G.; Olazar, M.; Aguado, R.; Lopez, G.; Arabiourrutia, M.; Bilbao, J., Catalytic

420

pyrolysis of high density polyethylene in a conical spouted bed reactor. Journal of Analytical

421

& Applied Pyrolysis 2007, 79, (1–2), 450-455.

422

(19) Elordi, G.; Olazar, M.; Castaño, P.; Artetxe, M.; Bilbao, J., Polyethylene Cracking on a

423

Spent FCC Catalyst in a Conical Spouted Bed. Ind.eng.chem.res 2012, 51, (43),

424

14008-14017.

425

(20) Mosio-Mosiewski, J.; Warzala, M.; Morawski, I.; Dobrzanski, T., High-pressure catalytic

426

and thermal cracking of polyethylene. Fuel Processing Technology 2007, 88, (4), 359-364.

427

(21) Renzini, M. S.; Sedran, U.; Pierella, L. B., H-ZSM-11 and Zn-ZSM-11 zeolites and their 20 ACS Paragon Plus Environment

Page 21 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

428

applications in the catalytic transformation of LDPE. Journal of Analytical & Applied

429

Pyrolysis 2009, 86, (1), 215-220.

430

(22) Uemichi, Y.; Makino, Y.; Kanazuka, T., Degradation of polyethylene to aromatic

431

hydrocarbons over metal-supported activated carbon catalysts. Journal of Analytical &

432

Applied Pyrolysis 1989, 14, (4), 331-344.

433

(23) Uemichi, Y.; Makino, Y.; Kanazuka, T., Degradation of polypropylene to aromatic

434

hydrocarbons over Pt- and Fe-containing activated carbon catalysts. Journal of Analytical &

435

Applied Pyrolysis 1989, 16, (3), 229-238.

436

(24) Liu, Y.; Li, K.; Liu, Y.; Pu, L.; Chen, Z.; Deng, S., The high-performance and mechanism

437

of P-doped activated carbon as a catalyst for air-cathode microbial fuel cells. Journal of

438

Materials Chemistry A 2016, 3, (42), 21149-21158.

439

(25) Malaika, A.; Rechnia-Gorący, P.; Kot, M.; Kozłowski, M., Selective and efficient

440

dimerization of isobutene over H3PO4 /activated carbon catalysts. Catalysis Today 2017.

441

(26) Ye, X.; Lu, Q.; Wang, X.; Guo, H.; Cui, M. S.; Dong, C.; Yang, Y., Catalytic fast

442

pyrolysis of cellulose and biomass to selectively produce levoglucosenone using activated

443

carbon catalyst. Acs Sustainable Chemistry & Engineering 2017, 5, (11).

444

(27) Lin, B.; Wang, J.; Huang, Q.; Ali, M.; Chi, Y.; Lin, B.; Wang, J.; Huang, Q.; Ali, M.; Chi,

445

Y., Aromatic recovery from distillate oil of oily sludge through catalytic pyrolysis over Zn

446

modified HZSM-5 zeolites. Journal of Analytical & Applied Pyrolysis 2017, 128.

447

(28) Yan, G.; Jing, X.; Wen, H.; Xiang, S., Thermal Cracking of Virgin and Waste Plastics of

448

PP and LDPE in a Semibatch Reactor under Atmospheric Pressure. Energy & Fuels 2015, 29,

449

(4), 2289-2298.

450

(29) Li, L.; Zhu, W.; Liu, Y.; Shi, L.; Liu, H.; Ni, Y.; Liu, S.; Zhou, H.; Liu, Z.,

451

Phosphorous-modified ordered mesoporous carbon for catalytic dehydrogenation of propane

452

to propylene. Rsc Advances 2015, 5, (69), 56304-56310.

453

(30) Asaftei, I. V.; Sandu, I.; Manea, L. R.; Birsa, L. M.; Earar, K., Conversion of Industrial

454

Feedstock mainly with Butanes and Butenes over HZSM-5 and Zn/HZSM-5 (nitrate)

455

Catalysts. Revista de Chimie -Bucharest- Original Edition- 2015, 66, (5), 673-680.

456

(31) Sakata, Y.; Uddin, M. A.; Muto, A., Degradation of polyethylene and polypropylene into 21 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 22 of 48

457

fuel oil by using solid acid and non-acid catalysts. Journal of Analytical & Applied Pyrolysis

458

1999, 51, (1-2), 135-155.

459

(32) Lin, Y. H.; Yang, M. H., Tertiary recycling of commingled polymer waste over

460

commercial FCC equilibrium catalysts for producing hydrocarbons. Polymer Degradation &

461

Stability 2009, 94, (1), 25-33.

462

(33) Buekens, A. G.; Huang, H., Catalytic plastics cracking for recovery of gasoline-range

463

hydrocarbons from municipal plastic wastes. Resources Conservation & Recycling 1998, 23,

464

(3), 163-181.

465

(34) Chaudhari, K.; Das, T. K.; Chandwadkar, A. J.; Sivasanker, S., Mesoporous

466

Aluminosilicate of the MCM-41 Type: Its Catalytic Activity in n -Hexane Isomerization.

467

Journal of Catalysis 1999, 186, (1), 81-90.

468

(35) Decastro, C.; Sauvage, E.; Valkenberg, M. H.; Hölderich, W. F., Immobilised Ionic

469

Liquids as Lewis Acid Catalysts for the Alkylation of Aromatic Compounds with Dodecene.

470

Journal of Catalysis 2000, 196, (1), 86-94.

471

(36) Crafa, S.; Varacca, D.; Yoshida, N., Characterization of clay-based K catalysts and their

472

application in Friedel-Crafts alkylation of aromatics. Applied Catalysis A General 1995, 132,

473

(1), 141-155.

474

(37) Song, Y.; Zhu, X.; Xu, L., Study on the process of transformation of olefin into aromatics

475

over HZSM-5. Catalysis Communications 2006, 7, (4), 218-223.

476

(38) Rosas, J. M.; Ruiz-Rosas, R.; Rodríguez-Mirasol, J.; Cordero, T., Kinetic study of the

477

oxidation resistance of phosphorus-containing activated carbons. Carbon 2012, 50, (4),

478

1523-1537.

479

(39) Bedia, J.; Rosas, J. M.; Márquez, J.; Rodríguez-Mirasol, J.; Cordero, T., Preparation and

480

characterization of carbon based acid catalysts for the dehydration of 2-propanol. Carbon

481

2009, 47, (1), 286-294.

482

(40) Rosas, J. M.; Bedia, J.; Rodríguez-Mirasol, J.; Cordero, T., HEMP-derived activated

483

carbon fibers by chemical activation with phosphoric acid. Fuel 2009, 88, (1), 19-26.

484

(41) Cordero, T.; Rodríguez-Maroto, J. M.; Rodríguez-Mirasol, J.; Rodríguez, J. J., On the

485

kinetics of thermal decomposition of wood and wood components. Thermochimica Acta 1990, 22 ACS Paragon Plus Environment

Page 23 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

486

164, (14), 135-144.

487

(42) Hita, I.; Cordero-Lanzac, T.; Gallardo, A.; Arandes, J. M.; Rodríguez-Mirasol, J.; Bilbao,

488

J.; Cordero, T.; Castaño, P., Phosphorus-containing activated carbon as acid support in a

489

bifunctional Pt–Pd catalyst for tire oil hydrocracking. Catalysis Communications 2016, 78,

490

48-51.

491

(43) Lukyanov, D. B., Application of a kinetic model for investigation of aromatization

492

reactions of light paraffins and olefins over HZSM-5. Studies in Surface Science & Catalysis

493

1997, 105, 1301-1308.

494

23 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

495

Tables

496

Table 1. Physicochemical properties of the different P-ACs.

Page 24 of 48

P content

BET surface area

Total pore volume

Average pore

(wt%)

(m2/g)

(cm3/g)

diameter (nm)

P-AC-10%

9.1

18.7

0.022

17.26

P-AC-20%

11.9

21.0

0.053

13.77

P-AC-30%

18.0

62.2

0.083

5.94

P-AC-40%

22.2

742.9

0.860

5.00

P-AC-50%

25.0

630.1

0.851

5.79

Sample

497 498

24 ACS Paragon Plus Environment

Page 25 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

499

Energy & Fuels

Table 2. Product yields under different P/WC ratios and residence times Group P/WC ratio

Residence

time Oil yield (%)

(s)

Coke

yield Gas yield (%)

(%)

0#

Quartz sand 3s

23.2±0.2%

0.2±0.1%

76.8

1#

10%

3s

27.0±0.8%

1.2±0.5%

71.8

2#

20%

3s

31.2±1.1%

2.3±0.2%

66.5

3#

30%

3s

35.1±0.6%

3.7±0.3%

61.2

4#

40%

3s

37.5±1.7%

6.1±0.4%

56.4

5#

50%

3s

41.8±1.4%

7.7±0.3%

50.5

6#

30%

1s

28.4±0.9%

1.6±0.4%

70.0

7#

30%

2s

31.3±0.8%

2.5±0.2%

66.2

8#

30%

4s

40.6±1.6%

4.1±0.8%

55.3

9#

30%

5s

40.8±1.4%

4.6±1.2%

54.6

500 501

25 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

502

Figures

503

Figure 1. The schematic layout of the experimental device.

Page 26 of 48

504 505

26 ACS Paragon Plus Environment

Page 27 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

506 507

Energy & Fuels

Figure 2. SEM pictures of (a) P-AC-10%, (b) P-AC-20%, (c) P-AC-30%, (d) P-AC-40%, and (e) P-AC-50%.

508 509

27 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

510 511

Page 28 of 48

Figure 3. The components of oil products catalyzed by P-ACs under (a) different P/WC ratios and (b) different residence times.

512 513

(a)

514 515 516

(b)

28 ACS Paragon Plus Environment

Page 29 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

517 518

519 520

Energy & Fuels

Figure 4. The isomerization and aromatization degrees of the oil products catalyzed by P-ACs under (a) different P/WC ratios and (b) different residence times.

(a)

521 522 523

(b)

29 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

524 525

Page 30 of 48

Figure 5. GC-MS chromatograms of oil products catalyzed by P-ACs at (a) different P/WC ratios and (b) different residence times.

526 527

(a)

30 ACS Paragon Plus Environment

Page 31 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

528 529 530

Energy & Fuels

(b)

31 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 32 of 48

532

Figure 6. The main aromatic compositions classified by the number of aromatic rings in the oil products catalyzed by P-ACs under (a) different P/WC ratios and (b) different

533

residence times.

531

534 535

(a)

536 537 538

(b)

32 ACS Paragon Plus Environment

Page 33 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

539 540

Energy & Fuels

Figure 7. The components of the oil products catalyzed by activated carbon modified by H3PO4, (NH4)2PO4, and HNO3.

541 542

33 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

543

Page 34 of 48

Figure 8. High resolution P 2p XPS spectra of P-AC-30%.

544 545

34 ACS Paragon Plus Environment

Page 35 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

546

Energy & Fuels

Figure 9. The main catalytic mechanism of PE pyrolysis catalyzed by P-AC.

547 548

35 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 1. The schematic layout of the experimental device. 44x12mm (300 x 300 DPI)

ACS Paragon Plus Environment

Page 36 of 48

Page 37 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

Figure 2. SEM pictures of (a) P-AC-10%, (b) P-AC-20%, (c) P-AC-30%, (d) P-AC-40%, and (e) P-AC-50%. 172x198mm (300 x 300 DPI)

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 3. The components of oil products catalyzed by P-ACs under (a) different P/WC ratios and (b) different residence times. 72x61mm (300 x 300 DPI)

ACS Paragon Plus Environment

Page 38 of 48

Page 39 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

Figure 3. The components of oil products catalyzed by P-ACs under (a) different P/WC ratios and (b) different residence times. 72x61mm (300 x 300 DPI)

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 4. The isomerization and aromatization degrees of the oil products catalyzed by P-ACs under (a) different P/WC ratios and (b) different residence times. 72x61mm (300 x 300 DPI)

ACS Paragon Plus Environment

Page 40 of 48

Page 41 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

Figure 4. The isomerization and aromatization degrees of the oil products catalyzed by P-ACs under (a) different P/WC ratios and (b) different residence times. 72x61mm (300 x 300 DPI)

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 5. GC-MS chromatograms of oil products catalyzed by P-ACs at (a) different P/WC ratios and (b) different residence times. 149x196mm (300 x 300 DPI)

ACS Paragon Plus Environment

Page 42 of 48

Page 43 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

Figure 5. GC-MS chromatograms of oil products catalyzed by P-ACs at (a) different P/WC ratios and (b) different residence times. 148x195mm (300 x 300 DPI)

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 6. The main aromatic compositions classified by the number of aromatic rings in the oil products catalyzed by P-ACs under (a) different P/WC ratios and (b) different residence times. 72x61mm (300 x 300 DPI)

ACS Paragon Plus Environment

Page 44 of 48

Page 45 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

Figure 6. The main aromatic compositions classified by the number of aromatic rings in the oil products catalyzed by P-ACs under (a) different P/WC ratios and (b) different residence times. 72x61mm (300 x 300 DPI)

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 7. The components of the oil products catalyzed by activated carbon modified by H3PO4, (NH4)2PO4, and HNO3. 72x61mm (300 x 300 DPI)

ACS Paragon Plus Environment

Page 46 of 48

Page 47 of 48 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

Figure 8. High resolution P 2p XPS spectra of P-AC-30%. 76x48mm (300 x 300 DPI)

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 9. The main catalytic mechanism of PE pyrolysis catalyzed by P-AC. 150x170mm (300 x 300 DPI)

ACS Paragon Plus Environment

Page 48 of 48