Effect of Antioxidants on the Storage Stability of Soybean-Oil-Based

Dec 15, 2009 - (1) The promise of biodiesel is tremendous, but some significant obstacles remain .... free glycerin (mass %), D 6584, 0.020, 0.006, 0 ...
0 downloads 0 Views 3MB Size
Energy Fuels 2010, 24, 2028–2033 Published on Web 12/15/2009

: DOI:10.1021/ef9012032

Effect of Antioxidants on the Storage Stability of Soybean-Oil-Based Biodiesel Haiying Tang, Rhet C. De Guzman, K. Y. Simon Ng, and Steven O. Salley* National Biofuels Energy Laboratory, Department of Chemical Engineering and Materials Science, Wayne State University, 5050 Anthony Wayne Drive, Detroit, Michigan 48202 Received October 21, 2009. Revised Manuscript Received November 24, 2009

Biodiesel is composed of the monoalkyl esters produced from a variety of animal fats or vegetable oils, which can be used in blends with conventional petroleum diesel in existing diesel engines. While having many desirable properties, poor oxidative and storage stabilities are a source of considerable concern. This paper presents results of studies on the effectiveness of various individual and binary antioxidants [(R-tocopherol (R-T), butylated hydroxyanisole (BHA), butyl-4-methylphenol (BHT), t-butylhydroquinone (TBHQ), 2,5-ditert-butyl-hydroquinone (DTBHQ), ionol BF200 (IB), propylgallate (PG), and pyrogallol (PY)] to improve the storage stability of soybean oil (SBO)- and distilled SBO-based biodiesel. Results indicate that the induction period (IP) of untreated SBO-based biodiesel significantly decreased with the increasing storage time, while the IP values with adding TBHQ to SBO-based biodiesel remained constant for up to 30 months. Moreover, the binary antioxidant formulations of THBQ/BHA maintained the IP of distilled SBO-based biodiesel stable over a 6 month period. TBHQ is the most effective antioxidant to improve the storage stability of SBO-based biodiesel.

temperature or air exposure alone had little effect. Lin et al.7 found that higher storage temperature and a longer storage time significantly accelerated the oxidative reaction in palm oil biodiesel. While the oxidative stability of biodiesel may be improved by modification of the fatty acid methyl ester (FAME) composition;8-10 this generally adversely affects low-temperature operability.11 Instead, antioxidant additives (between 200 and 1000 ppm) are commonly employed to improve the oxidative stability of biodiesel. Many studies have demonstrated that antioxidants can improve the oxidative stability of biodiesel.12-15 The addition of 400 ppm of pyrogallol (PY) can significantly improve the oxidative stability of rapeseed-oil-, sunflower-oil-, and used-frying-oil-based biodiesel.16 Our previous study17,18 also showed that different antioxidants [butylated hydroxyanisole (BHA), butyl-4-methylphenol (BHT), t-butylhydroquinone (TBHQ), 2,5-ditert-butylhydroquinone (DTBHQ), ionol BF200 (IB), propylgallate (PG), and PY] can enhance the oxidative stability of soybean oil (SBO)-, cottonseed oil (CSO)-, poultry fat (PF)-, and yellow

1. Introduction Biodiesel is a domestic, renewable fuel that is gaining wide acceptance. When blended with conventional petroleum diesel, biodiesel reduces exhaust emissions, improves lubricity, and can raise the cetane number.1 The promise of biodiesel is tremendous, but some significant obstacles remain for its complete acceptance by diesel engine manufacturers. Biodiesel derived from many vegetable oils and animal fats possesses significant amounts of unsaturated fatty acid methyl ester (UFAME), and the polyunsaturated fatty acid esters in UFAME are very prone to oxidative degradation.2 Biodiesel stability is dependent upon oxidation stability (the influence of oxygen), thermal stability (the influence of temperature in the absence of oxygen), and storage stability (the influence of time).3 Biodiesel degradation is caused by an auto-oxidation chain mechanism.4 The location and number of double bonds in UFAME affect the susceptibility of the fatty acids chain to oxygen attack.5 The relative rates of oxidation of methyl oleate (C18:1), methyl linoleate (C18:2), and methyl linolenate (C18:3) are 1, 41, and 98, respectively.5 Moreover, environmental factors affect the stability of biodiesel. Leung et al.6 reported that high temperature together with air exposure greatly increased the biodiesel degradation rate but high

(7) Lin, C. Y.; Chiu, C. C. Energy Fuels 2009, 23, 3285–3289. (8) Falk, O.; Meyer-Pittroff, R. Eur. J. Lipid Sci. Technol. 2004, 106 (12), 837–843. (9) Knothe, G. Energy Environ. Sci. 2009, 2 (7), 759–766. (10) Knothe, G. Energy Fuels 2008, 22 (2), 1358–1364. (11) Moser, B. R. In Vitro Cell. Dev. Biol.: Plant 2009, 45 (3), 229–266. (12) Liang, Y. C.; May, C. Y.; Foon, C. S.; Ngan, M. A.; Hock, C. C.; Basiron, Y. Fuel 2006, 85 (5-6), 867–870. (13) Liang, C.; Schwarzer, K. J. Am. Oil Chem. Soc. 1998, 75 (10), 1441–1443. (14) Sendzikiene, E.; Makareviciene, V.; Janulis, P. Pol. J. Environ. Stud. 2005, 14 (3), 335–339. (15) Domingos, A. K.; Saad, E. B.; Vechiatto, W. W. D.; Wilhelm, H. M.; Ramos, L. P. J. Braz. Chem. Soc. 2007, 18 (2), 416–423. (16) Pahgova, J.; Jorikova, L.; Cvengros, J. Energy Fuels 2008, 22 (3), 1991–1996. (17) Tang, H. Y.; Wang, A. F.; Salley, S. O.; Ng, K. Y. S. J. Am. Oil Chem. Soc. 2008, 85 (4), 373–382. (18) de Guzman, R.; Tang, H. Y.; Salley, S.; Ng, K. Y. S. J. Am. Oil Chem. Soc. 2009, 86 (5), 459–467.

*To whom correspondence should be addressed. Telephone and Fax: 001-313-832-2643. E-mail: [email protected]. (1) Krawczyk, T. Information 1996, 7, 801–829. (2) Hoshino, T.; Iwata, Y.; Koseki, H. J. Therm. Sci. 2007, 11 (2), 87– 100. (3) Mittelbach, M.; Remschmidt, C. Biodiesel;The Comprehensive Handbook; Martin Mittelbach: Graz, Austria, 2004. (4) Waynick, J. A. Characterization of biodiesel oxidation and oxidation products. National Renewable Energy Laboratory, Golden, CO, Nov 2005; NREL/TP-540-39096. (5) Neff, W. E.; Selke, E.; Mounts, T. L.; Rinsch, W.; Frankel, E. N.; Zeitoun, M. A. M. J. Am. Oil Chem. Soc. 1992, 69 (2), 111–118. (6) Leung, D. Y. C.; Koo, B. C. P.; Guo, Y. Bioresour. Technol. 2006, 97 (2), 250–256. r 2009 American Chemical Society

2028

pubs.acs.org/EF

Energy Fuels 2010, 24, 2028–2033

: DOI:10.1021/ef9012032

Tang et al.

Table 1. Detroit Average Temperature (°C) from February 2009 to September 2009 maximum (°C) minimum (°C) average (°C)

February 2009

March 2009

April 2009

May 2009

June 2009

July 2009

August 2009

September 2009

10 -12 -2

15 -10 3

23 0 9

23 11 16

27 13 19

27 17 21

27 14 22

23 16 19

grease (YG)-based biodiesel at the varying concentrations between 250 and 1000 ppm. The effect of each antioxidant on biodiesel differs depending upon the different feedstock. However, few studies investigated the effect of the antioxidant on long-term storage stability. One study of the addition of BHT to palm oil biodiesel demonstrated significant oxidation over a 3000 h period.7 The aim of this study is to evaluate different individual antioxidant additives on the induction period (IP), acid number, and viscosity of SBO-based biodiesel during long-term storage, as well as the efficacy of binary antioxidants on distilled SBO-based biodiesel under long-term storage. Moreover, the FAME content, FAME composition, and antioxidant content after long-term storage were investigated.

specified standard method for oxidative stability for biodiesel in accordance with EN 14112.20 The absolute difference between two independent single test results did not exceed the repeatability limit of the EN 14112 method. The IP for 100% biodiesel (B100) specified in ASTM D6751-0821 is not less than 3 h. 2.2.4. Kinematic Viscosity and Acid Number. The kinematic viscosity of biodiesel at 40 °C was determined following ASTM D 44522 using a Rheotek AKV8000 automated kinematic viscometer (Poulten Selfe and Lee Ltd., Essex, U.K.). The acid number of biodiesel was determined according to ASTM D 66423 using a Brinkman/Metrohm 809 Titrando (Westbury, NY). The kinematic viscosity and acid number specified in ASTM D6751-08 is 1.0-6.0 mm2/s and not more than 0.50 mg of KOH/g, respectively. Tests results are reported as the mean of triplicate runs (the Rancimat results are repeatable within (5%) within the repeatability limits of their respective standard method. 2.3. Long-Term Storage Stability. 2.3.1. Individual Antioxidants. SBO-I-based biodiesel both with and without different antioxidants at a concentration of 1000 ppm was stored in 3 gallon carbon-steel containers. The containers were not purged with nitrogen and were not airtight to allow the sample contact with air. The containers were stored at room temperature (23 °C). Samples of 100 mL were periodically taken for determination of the acid number, kinematic viscosity, IP, and the concentration of antioxidant and biodiesel. 2.3.2. Binary Antioxidants. DSBO-II-based biodiesel with 500 ppm of TBHQ/BHA (2:1), TBHQ/PG (1:1), and TBHQ/ PY (1:1) antioxidant mixtures were stored in 3 gallon carbon-steel containers. The containers were not purged with nitrogen and were not airtight to allow the sample contact with air. One set of samples was stored indoors (at room temperature, 23 °C), and the others were stored outdoors (at Michigan ambient temperature from February 2009 to September 2009). The recorded ambient temperature value ranged between -12 and 27 °C (Table 1).

2. Experimental Section 2.1. Materials. Biodiesel was obtained directly from Biodiesel Industries (Denton, TX, herein called SBO-I-based biodiesel) and NextDiesel (Adrian, MI, herein called SBO-II-based biodiesel). Distilled SBO-II (DSBO-II)-based biodiesel was produced by vacuum distilling under reduced pressure (3 10-3 torr) and a temperature range of 130-150 °C using a Koehler (Bohemia, NY) K80200 vacuum distillation apparatus. The antioxidants, R-tocopherol (R-T, 1000 IU/g), BHA (98.5%), BHT, DTBHQ (99%), PG, TBHQ (97%), PY (99%), heptane (>99% capillary GC), and N-methyl-N-trimethylsilytrifluoroacetamide (MSTF) were purchased from Sigma-Aldrich, Inc. (St. Louis, MO). Ionol BF200 (IB) was obtained from Degussa Sant Celoni (Barcelona, Spain). 1,2,4-Butanetriol [1 mg/mL, internal standard 1 (ISTD1)] in pyridine was obtained from Supelco (Bellefonte, PA). Up to 1000 ppm of antioxidants could dissolve in the biodiesel samples. 2.2. Analysis. 2.2.1. FAME Composition. The FAME composition and content of biodiesel was determined using PerkinElmer Clarus 500 gas chromatography-mass spectrometry (GC-MS) with a split automatic injector and a Rtx-WAX (Restek, Bellefonte, PA) column (length, 60 m; inner diameter, 0.25 mm; coating, 0.25 μm). Details of the procedure have been described elsewhere.19 The column was held at 120 °C for 1 min, ramped to 240 °C at 20 °C/min, and then held at 240 °C for 13 min. The transfer line between GC and MS was kept at 240 °C. 2.2.2. Antioxidant Content by GC-Flame Ionization Detector (FID). The contents of TBHQ and PY were analyzed with a PerkinElmer Clarus 500 GC-FID. The sample (∼100 mg) was mixed with 100 μL of ISTD1 and 100 μL of MSTFA in a vial and allowed to sit for 30 min at room temperature. Finally, 2 mL of heptane was added to the vial. A PE-5HT column (15 m in length, a 0.32 mm internal diameter, and a 0.1 μm film thickness) obtained from PerkinElmer, Shelton, CT, was held at 50 °C for 1 min and then ramped to 180 °C at 15 °C/min, 230 °C at 7 °C/min, and 380 °C at 30 °C/min. Finally, it was held at 380 °C for 10 min. Hydrogen (99.9999%, Cryogenic Gases, Detroit, MI) was used as the carrier gas, with a flow rate of 3 mL/min. 2.2.3. Oxidative Stability. Oxidative stability of biodiesel with and without the addition of the antioxidant was determined according to the Rancimat method using a Metrohm 743 Rancimat instrument (Herisau, Switzerland). The Rancimat test is the

3. Results and Discussion 3.1. Analysis of Biodiesel Samples. Physical property data on the SBO-I- and DSBO-II-based biodiesel are given in Table 2. On the whole, most of the values were within the limits given by ASTM D 6751-08.21 SBO-I-based biodiesel met the limit of a 3 h IP; however, DSBO-II-based biodiesel did not meet the oxidative stability specification, which was caused by significantly removing the natural antioxidant during the distillation process.24 (20) European Committee for Standardization (CEN). EN 14112. Determination of oxidation stability (accelerated oxidation test). European Committee for Standardization; CEN Press: Brussels, Belgium, 2003. (21) American Society for Testing and Materials (ASTM). ASTM D 6751-08 Annex A.1. Standard specification for biodiesel fuel blend stock (B100) for middle distillate fuels. Annual Book of ASTM Standards; ASTM Press: West Conshohocken, PA, 2008. (22) American Society for Testing and Materials (ASTM). ASTM D445-06. Standard test method for kinematic viscosity of transparent and opaque liquids (and calculation of dynamic viscosity).Annual Book of ASTM Standards; ASTM Press: West Conshohocken, PA, 2006. (23) American Society for Testing and Materials (ASTM). ASTM D 664-06. Standard test method for acid number of petroleum products by potentiometric titration. Annual Book of ASTM Standards; ASTM Press: West Conshohocken, PA, 2006. (24) Tang, H.; Rhet, D. G.; Simon Ng, K. Y.; Steve, O. S. J. Am. Oil Chem. Soc. 2009, manuscript in process.

(19) Tang, H. Y.; Salley, S. O.; Ng, K. Y. S. Fuel 2008, 87 (13-14), 3006–3017.

2029

Energy Fuels 2010, 24, 2028–2033

: DOI:10.1021/ef9012032

Tang et al.

Table 2. Physical Properties of SBO-I- and DSBO-II-Based Biodiesel viscosity at 40 °C (mm /s) acid number (mg of KOH/g) free glycerin (mass %) total glycerin (mass %) cloud point (°C) pour point (°C) cold filter plugging point (°C) oxidative stability IP (h) 2

a

ASTM method

ASTM specificationa

SBO-I

DSBO-II

D 445 D 664 D 6584 D 6584 D 2500 D 97 D 6371 EN 14112

1.9-6.0 0.5 maximum 0.020 0.24 report

4.34 0.22 0.006 0.177 3 -3 -3 3.52

3.99 0.31 0 0 -1 0 -2 0.17

3 minimum

The specification is given in ref 1.

Figure 1. Effects of 1000 ppm of R-T, IB, BHT, BHA, DTBHQ, TBHQ, PG, and PY on the IP of SBO-I-based biodiesel as a function of the indoor stored time.

Figure 2. Acid number of SBO-I-based biodiesel with or without antioxidants as a function of the indoor storage time.

3.2. Effect of Individual Antioxidants. Figure 1 shows the IP of SBO-I-based biodiesel with or without different antioxidants over a period of 30 months. The IP of untreated SBO-I-based biodiesel gradually decreased from 3.5 to 0.3 h over 30 months, while the biodiesel with TBHQ was found to be very stable. The IP of biodiesel with R-T decreased from 3.84 to less than 3 h after 2 months of storage, while biodiesel with PY failed the oxidative stability specification after 4 months. The values of IP of SBO-I-based biodiesel with PY, PG, DTBHQ, BHA, BHT, and IB are significantly increased to 11.5, 10.3, 6.5, 6.6, 6.4, and 5.9 h at the initial time, respectively, but significantly decreased over the 30 month period. The addition of BHA and BHT could retain the IP above 3 h for 12 months, while IB and DTBHQ reached 18 months, followed by PG for 24 months. The rank of antioxidants upon improving storage stability during the 30 month period is TBHQ . PG > IB ∼ DTBHQ > BHA ∼ BHT > PY >R-T. TBHQ can maintain storage stability of biodiesel for the long term. The antioxidant R-T was less effective on the oxidative and storage stabilities than the synthetic antioxidants. This result agrees with a similar study, which showed that TBHQ in SBO-based biodiesel was more effective than R-T for 3 months.25 Figure 2 shows the acid number of SBO-I-based biodiesel with different antioxidants as a function of the storage time. The acid number for untreated SBO-I-based biodiesel increased with time and reached 0.52 mg of KOH/g after 18 months. Samples with antioxidants R-T, BHT, BHA, and DTBHQ had a slight increase in the acid number during the first 9 month period and then significantly increased, exceeding the ASTM D 6751-08 specification after 24 months. IB and TBHQ had a very slow increase in the acid number

Figure 3. Kinematic viscosity of SBO-I-based biodiesel with or without antioxidants at 40 °C as a function of the indoor storage time.

during the first 18 month period and exceeded the ASTM D 6751-08 specification after 30 months. The viscosity of SBO-I-based biodiesel with different antioxidants as function of the storage time was also measured (Figure 3). The viscosity for untreated SBO-I-based biodiesel increased from 4.3 to 5 mm2/s over the 30 month period. On the other hand, adding TBHQ resulted in a stable viscosity (4.3 mm2/s) over the entire 30 month period. For biodiesel with added R-T, BHA, DTBHQ, and PY, a slow increase in the viscosity during the first 12 month period was observed and then a rapid increase after that. The viscosity of biodiesel with IB, BHT, and PG only had a slight increase during the 30 month period. It should be noted that the ASTM D 6751-08 specification (1.9-6.0 mm2/s) at 40 °C was not exceeded in any of the cases. This result is in agreement with a previous study that recommended that

(25) Moser, B. R. Eur. J. Lipid Sci. Technol. 2008, 110 (12), 1167–1174.

2030

Energy Fuels 2010, 24, 2028–2033

: DOI:10.1021/ef9012032

Tang et al.

Table 3. Effect of Antioxidants on the FAME Content of SBO-I-Based Biodiesel after 18, 24, and 30 Months of Indoor Storage FAME content by GC-MS time (months)

control (%)

TBHQ (%)

PG (%)

PY (%)

IB (%)

BHA (%)

R-T (%)

BHT (%)

DTBHQ (%)

0 18 24 30

100 93.1 90.9 87.5

100 97.2 98.2 98.9

100 96.4 96.4 96.4

100 93.7 91.9 88.2

100 96.9 95.2 97.1

100 94.1 92.1 90.0

100 92.3 90.6 86.8

100 96.5 96.0 96.0

100 97.0 94.2 95.1

Table 4. Effect of the Antioxidant Concentration as a Function of the Indoor Storage Time antioxidant concentration (ppm) time

TBHQ

PY

control 18 months 24 months 30 months

1000 764 677 575

1000