Energy and Electron Transfer Cascade in Self-Assembled Bilayer Dye

Oct 4, 2016 - Presumably a decrease in dye regeneration rate is at least partially ... The curves were well fit by using the equivalent circuit previo...
0 downloads 0 Views 615KB Size
Subscriber access provided by CORNELL UNIVERSITY LIBRARY

Article

Energy and Electron Transfer Cascade in SelfAssembled Bilayer Dye-Sensitized Solar Cells Omotola Olukemi Ogunsolu, Ian A Murphy, Jamie C Wang, Anjan Das, and Kenneth Hanson ACS Appl. Mater. Interfaces, Just Accepted Manuscript • DOI: 10.1021/acsami.6b09955 • Publication Date (Web): 04 Oct 2016 Downloaded from http://pubs.acs.org on October 6, 2016

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

ACS Applied Materials & Interfaces is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 23

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Energy and Electron Transfer Cascade in SelfAssembled Bilayer Dye-Sensitized Solar Cells Omotola O. Ogunsolu,a† Ian A. Murphy,b† Jamie C. Wang,b Anjan Das,b and Kenneth Hansona,b* a

Materials Science and Engineering, Florida State University, Tallahassee, Florida 32306, United States b Department of Chemistry and Biochemistry, Florida State University, Tallahassee, Florida 32306, United States Keywords: self-assembly, energy transfer, electron transfer, bilayer, DSSC

ABSTRACT Current high efficiency dye-sensitized solar cells (DSSCs) rely on the incorporation of multiple chromophores, via either co-deposition or pre-formed assemblies, as a means of increasing broad band light absorption. These strategies have some inherent limitations including decreased total light absorption by each of the dyes, low surface loadings, and complex synthetic procedures. In this report, we introduce an alternative strategy, self-assembled bilayers, as a simple, step-wise method of incorporating two complementary chromophores into a DSSC. The bilayer devices exhibit a 10% increase in Jsc, Voc and η over the monolayer devices due to increased incident photon-to-electron conversion efficiency across the entire visible spectrum and slowed recombination losses at the interface. Directional energy and electron transfer towards the metal oxide surface are key steps in the bilayer photon-to-current generation process. These results are important as they open the door to a new architecture for harnessing broad band light in dyesensitized devices. ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 2 of 23

INTRODUCTION Dye-sensitized solar cells (DSSCs) are a promising alternative to traditional silicon solar cells due to their ease of fabrication and lower manufacturing costs.1, 2 In DSSCs, the crucial first step in efficient solar energy conversion is to maximize light absorption by the surface bound dye molecule.2,

3

Unfortunately, unlike inorganic crystalline materials which have broad band

absorption features,4 molecules typically exhibit relatively narrow absorption transitions resulting in transmission losses and decreased efficiencies.5 One strategy to fill these absorption gaps is to incorporate, either by co-deposition6,

7

or in pre-formed assemblies,8 two or more

molecules with complementary absorption spectra onto the metal oxide surfaces. The highest efficiency DSSCs yet reported (>13%) utilize co-deposition of two complementary dyes.9,

10

This strategy has the advantage of absorbing a larger portion of the

solar spectrum but, due to limited surface area at a given film thickness, it decreases the total absorbance of each chromophore. The decreased surface area can be mitigated by increasing the film thickness, but thicker films are detrimental because 1) they increase the likelihood of deleterious recombination events,11,

12

and 2) they slow diffusion of redox mediators into the

porous films.13, 14 Alternatively, molecular assemblies composed of two dyes and a surface binding group can be prepared prior to film loading.8,

15-18

This strategy has received less attention than co-

deposition and limited success presumably because these assemblies typically require a complex, multistep synthesis with cumulatively low yields and low surface loadings (