Enhanced Electrochemical Performance of Fast ... - ACS Publications

Subscriber access provided by - Access paid by the | UCSB Libraries

Energy, Environmental, and Catalysis Applications

Enhanced Electrochemical Performance of Fast Ionic Conductor LiTi2(PO4)3 Coated LiNi1/3Co1/3Mn1/3O2 Cathode Material Lu-Lu Zhang, Ji-Qing Wang, Xue-Lin Yang, Gan Liang, Tao Li, Peng-Lin Yu, and Di Ma ACS Appl. Mater. Interfaces, Just Accepted Manuscript • DOI: 10.1021/acsami.7b19692 • Publication Date (Web): 16 Mar 2018 Downloaded from http://pubs.acs.org on March 17, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Enhanced Electrochemical Performance of Fast Ionic Conductor LiTi2(PO4)3 Coated LiNi1/3Co1/3Mn1/3O2 Cathode Material Lu-Lu Zhang1, Ji-Qing Wang1, Xue-Lin Yang1,* Gan Liang2, Tao Li1, Peng-Lin Yu1, Di Ma1 1

College of Materials and Chemical Engineering, Hubei Provincial Collaborative Innovation Center for New Energy Microgrid, China Three Gorges University, 8 Daxue Road, Yichang, Hubei 443002, China

2

Department of Physics, Sam Houston State University, Huntsville, Texas 77341, USA.

*Corresponding author: E-mail: [email protected]

1

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ABSTRACT: Layered LiNi1/3Co1/3Mn1/3O2 (NCM333) is successfully coated by fast ionic conductor LiTi2(PO4)3 (LTP) via wet chemical method. The effects of LTP on the physicochemical properties and electrochemical performance are studied. The results reveal that a highly layered structure of NCM333 can be well maintained with less cation mixing after LTP coating. LTP about 5 nm thickness is coated on the surface of NCM333. Such LTP coating layer can effectively suppress the side reactions between NCM333 and electrolyte but will not hinder the lithium ion transmission. As a result, LTP coated NCM333 owns an improved capability and cyclic performance, e.g., NCM333/LTP delivers an initial capacity as high as 121.0 mAh g-1 with a capacity retention ratio of 82.3 % after 200 cycles at 10 C, while NCM333 only has an initial capacity of 120.4 mAh g-1 with a very low capacity retention ratio of 66.4 %. This method of using fast ionic conductor like LTP as a coating material may provide a simple and effective strategy to modify those electrode materials with poor cyclic performance. KEYWORDS: Lithium ion battery, Cathode material, LiNi1/3Co1/3Mn1/3O2, LiTi2(PO4)3, Coating.

2


Page 2 of 31

Page 3 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


1. INTRODUCTION Due to the serious environmental pollution caused by the use of fossil fuels in automobiles, there is an urgent and expanding demand for people to develop clean and more efficient new power sources such as lithium ion batteries (LIBs).1 Particularly, owing to the high energy density, large power capability, long cycle life and no memory effect, LIBs are regarded as an ideal power source for a wide range of applications.2 So far, some cathode materials for LIBs, such as layered LiCoO2,3 olivine LiFePO44 and spinel LiMn2O4,5 have been widely used as cathode materials for commercial LIBs in electrical vehicles (EVs) or hybrid electric vehicles (HEVs). Among them, the further development of the earliest commercialized LiCoO2 is being restricted because of the relatively high cost and the toxicity of cobalt limit its future applications.6-8 Thus, in the last two decades, researchers have been working on finding alternative cathode materials to satisfy the required environmental, safety and cost standards for LIBs.9,11 In comparison with LiCoO2, layered LiNixCoyMnzO2 (x+y+z=1) has been considered more suitable for EVs or HEVs because of its low cost, high capacity and high safety. In 1999, Liu et al.12 first proposed different atomic composition ratios of Ni, Co, and Mn including ratios of x:y:z = 7:2:1, 5:2:3 and 6:2:2. In 2001, Ohzuku et al.13 successfully synthesized LiNi1/3Co1/3Mn1/3O2 (abbreviated as NCM333) as a cathode material. Compared to NCM721, NCM523 and NCM622, NCM333 appears easier to prepare and shows better cycle performance and structural stability. Thus, NCM333 draws much attention in the field of cathode materials for LIBs. Later, Li et al.14 also obtained porous nano-micro hierarchical NCM333 3



microspheres with a high discharge capacity of 133.2 mAh g-1 at 1 C via a facile nano-etching-template route. However, the poor electronic conductivity, transition metal dissolution and some side reactions between NCM333 and electrolyte lead to a poor rate capability and cyclic stability of NCM333,15-18 which seriously plagues its large-scale applications. Since then, researchers worldwide have proposed various ways to overcome these drawbacks. For example, coating could be an easy and effective way to increase the electronic conductivity of NCM333 and inhibit the side reactions between NCM333 and electrolyte.17 Various coating materials including carbon18 and metal oxides (Al2O3,19 Li2TiO3,20 ZrO2,21 TiO2,22 AlF3,23 AlPO4,24 etc) have been studied. Very recently, Yang et al.18 used a one-step method to prepare carbon coated NCM (NCM333/C) with active carbon as reaction matrix, and this NCM333/C cathode material delivered a discharge capacity of 191.2 mAh g-1 at 0.5 C (85 mA g-1). However, the oxidation of carbon in air during high-temperature sintering process leads to the uncontrollable formation of coating layer on the surface of NCM333. By comparison, metal oxides coating layer can be easily achieved and the cycling performance could also be enhanced by oxide coating due to the improved structural stability. But, the rate capability may be hindered simultaneously because of the low lithium ion diffusion rate of metal oxide.25 Interestingly, NASICON lithium titanium phosphate LiTi2(PO4)326,27 (abbreviated as LTP) has a three-dimensional open framework and fast ion diffusion rate, thus it could be used as an ideal coating material for NCM333.

4


Page 4 of 31

Page 5 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


In this work, we introduced the fast ionic conductor LTP to modify NCM333 through a facile synthetic route for the first time. The phase, morphology, microstructure, valence state of key elements and magnetic property of the as-obtained LTP coated NCM333 cathode material were carefully investigated, and the roles that the coated LTP layer plays in improving the electrochemical performance of NCM333/LTP will be also discussed. 2. EXPERIMENTAL SECTION Pristine NCM333 was synthesized by blending Ni1/3Co1/3Mn1/3(OH)2 precursor prepared by a co-precipitation method and lithium carbonate (Li2CO3) with a molar ratio of 1:1.06.28 The mixture was calcined at 450 oC for 5 h, and then at 900 oC for 12 h in air to obtain the pristine NCM333 sample. The LTP coated NCM333 sample was prepared by a wet-chemical method as follows. First, the as-prepared NCM333 was dispersed in a mixed solution of ethanol and acetone, and stirred constantly for 1 h to obtain a suspension. Then a certain amount of tetrabutyl titanate (C16H36O4Ti) was added to keep the LTP content of 2 wt. % and stirred for 0.5 h. Subsequently, stoichiometric lithium hydroxide (LiOH·H2O) and ammonium dihydrogen phosphate (NH4H2PO4) were dissolved in 20 mL deionized water under magnetic stirring for 0.5 h, and then added into the above NCM ethanol/acetone mixed solution drop by drop and stirred for 9 h. The resulted precipitate was collected by filtration and dried. Finally, the dried precipitate was heated at 500 oC for 5 h in air, and then cooled to room temperature to obtain the LTP coated NCM333 composite (denoted as

5



NCM/LTP). The schematic illustration of this synthesis route is displayed in Figure 1a. The materials characterization and electrochemical measurements sections are detailed in the Supporting Information. 3. RESULTS AND DISCUSSION XRD patterns and the corresponding Rietveld refinement results of the two as-prepared samples are displayed in Figures 1b-d. Figure 1b clearly shows that the two XRD patterns are similar and all the diffraction lines can be indexed with the hexagonal α-NaFeO2 crystal structure29 in Figure 1e. No impurity was observed in the two XRD patterns of NCM333 and NCM333/LTP, indicating that incorporating LTP does not affect the NCM333 crystal structure. Moreover, both samples have well-ordered layered structures, as can be indicated by the splitting of peaks (006)/(102) and (018)/(110).30,31 The intensity ratios of the (003) to (104) peaks of both NCM333 (~1.63) and NCM333/LTP (~1.68) are greater than 1.2, corresponding to a low degree of cation mixing.32,33 Furthermore, Rietveld refinements were carried out by using the GSAS software.34,35 As shown in Figures 1c, d and Table 1, the low error factors (Rp and Rwp) for both samples are indicative of the reliability of the refinement results. The c/a ratios of NCM333 (4.9756) and NCM333/LTP (4.9773) are both larger than 4.9, which further confirm the highly layered structure and lower cation mixing for both samples.28,36 Noting that, according to the measured Ti content (0.48 wt. %) by ICP, the actual coating amount of LTP can be calculated to be 1.94 wt. %, which is very close to the theoretical value of LTP (2.0 wt. %). Just owing to 6


Page 6 of 31

Page 7 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


the low concentration of LTP in NCM333/LTP, diffraction lines for LTP are not observed in the XRD pattern of NCM333/LTP. The morphology and size distribution of NCM333 and NCM333/LTP powders were investigated by SEM and a Nano Measurer particle size analysis software, respectively. From Figure 2, it is clearly seen that both samples exhibit an approximate square shape and have the same size distribution, and the average particle size is about 150 nm. To further study the microstructure of the two samples, TEM pictures were also presented in Figures 3a and b. Clearly, the average particle size for both samples is about 150 nm, which agrees well with the SEM results. As displayed in the HRTEM image of NCM333/LTP (Figure 3c), a coating layer with an average thickness of ~5 nm is obviously observed on the NCM333 surface. The magnified image in Figure 3d clearly shows a lattice spacing of 0.186 nm, representing the (015) planes of NCM333; meanwhile, on the edge of NCM333 particle, other clear lattice spacings of 0.348 and 0.269 nm are also observed, which are related to the (202) and (116) planes of LTP, respectively. This observation reveals that the coating material is LTP, and such LTP layer may effectively suppress side reactions between NCM333 and electrolyte; also, as a fast ionic conductor, the thin LTP coating layer will not hinder lithium ion transmission. In addition, the elemental distribution of NCM333/LTP sample is analyzed by EDS mapping (Figures 3e and f). Obviously, Ti shows a similar distribution as Ni, Co and Mn, which indicate that besides Ni, Co and Mn of NCM333, Ti is also uniformly dispersed in NCM333/LTP powders. 7



The XPS measurements were performed to study the composition and valence state of key elements in NCM333 and NCM333/LTP. The full XPS spectra in Figure 4a clearly show the presence of Ni, Co and Mn in these two samples, but the Ti and P peaks can only be observed in the spectrum of NCM333/LTP. In Figures 4b-d, the peaks of Ni3p1/2, Co2p3/2 and Mn2p1/2 are observed for NCM333 at 67.30, 780.10 and 654.10 eV, respectively, indicating the corresponding transition metal ions are Ni2+, Co3+ and Mn4+, respectively. This result is well matched with previous reports.30,31 In addition, to further verify the existing position of LTP, Ar-ion sputtering was done to strip different depths of NCM333/LTP in the XPS measurements (Figures 4e-h). Because all the XPS peaks in the interior deviate slightly to lower binding energy in comparison with those on the surface caused by the chemical reduction of Ar-ion, we use the peaks before sputtering (the black lines in Figures 4e-h) to confirm the valence states of key elements in NCM333/LTP. The banding energies of Ni3p1/2, Co2p3/2 and Mn2p1/2 peaks for NCM333/LTP at 67.50, 780.10, and 654.30 eV confirm that the valence of Ni, Co and Mn is still +2, +3 and +4, respectively, which demonstrates that LTP coating does not change the valence of Ni, Co and Mn in NCM333/LTP. As seen in Figure 4h, the binding energy of the Ti2p3/2 peak at 458.10 eV before sputtering confirms the Ti ions in NCM333/LTP are Ti4+.37,38 Moreover, from Figures 4e-h, it can be clearly observed that the peak intensity of Ni3p1/2, Co2p3/2 and Mn2p1/2 on the surface is weaker than those in the interior, but the Ti2p3/2 peak on the surface has stronger intensity than those at different depths from the NCM333/LTP surface; and with the increase of sputtering times, the XPS intensity of Ti peaks decreases 8


Page 8 of 31

Page 9 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


gradually. The two observations support the results from HRTEM images that the LTP layer has been successfully coated on the surface of NCM333 particles. Such LTP coating layer plays a vital role in inhibiting the side reactions between NCM333 and electrolyte.24,25 This could in turn improve the cyclic performance of NCM333/LTP. Meanwhile, as a fast ionic conductor, the thin LTP coating layer can increase the lithium ion diffusion rate, thus improve the capacity performance for NCM333/LTP. Figure 5 shows the temperature dependent magnetic susceptibility χ(T) and reciprocal magnetic susceptibility χ-1(T) for NCM333 and NCM333/LTP. χ(T) was measured in both field cooling (FC) and zero-field-cooling (ZFC) modes at a magnetic field of H = 1 kOe and in a temperature range of 5 K ≤ T ≤ 300 K. The χ-1(T) curve displayed in Figure 5a for NCM333 exhibits a paramagnetic linear behavior above 150 K and can be fitted to the Curie-Weiss law χ(T) = C/(T−θp) in the whole temperature range of 150 K ≤ T ≤ 300 K with Curie constant C = 1.063 emu·K·Oe-1·mole-1 and the paramagnetic Curie-Weiss temperature θp = -110 K. The value of the effective moment µeff is estimated to be 2.92 µB per formula unit (f. u.) for NCM333 from the formula µeff = (8C)1/2, which is almost the same as the value 2.90 µB reported previously by Hashem et al.39 and quite close to the theoretical value of 2.75 µB calculated by using the theoretical values of effective moment for Ni2+, Mn4+, and Co3+.40 This magnetic result is consistent with our XPS results that the valence values of Ni, Mn and Co in the NCM333 sample are +2, +4 and +3, respectively. The χ-1 data shown in Figure 5b for NCM333/LTP can also be fit to the 9



Curie-Weiss law in the same temperature range 150 K ≤ T ≤ 300 K and the fitting result gives C = 1.133 emu·K·Oe-1·mole-1 and θp = -108 K. The effective moment µeff estimated by µeff = (8C)1/2 is 3.01 µB, which is very close to the µeff value (2.92µB) for NCM333. This result is also in good agreement with our XPS results that Ti in the very low-level coating LTP layer is in the Ti4+ configuration (for which µeff is zero) and thus the Ti ions basically do not contribute to the magnetic moment of NCM333/LTP. Compared with the value θp = -110 K for NCM333, the slightly less negative value of θp (= -108 K) for NCM333/LTP indicates that the thin LTP coating layer might have a very small surface disturbance to the antiferromagnetic type interaction (or Weiss molecular field) between the transition metal ions in the NCM333 particles. In order to investigate the electrochemical reversibility and kinetic behavior, CV tests of the NCM333 and NCM333/LTP fresh electrodes were conducted in the voltage range of 2.8-4.5 V with a scan rate of 0.05 mV s-1 for the first three cycles. As shown in Figures 6a and b, the two CV curves exhibit a distinct pair of redox peaks around 3.70/3.80 V during Li+ ions insertion/deinsertion process, corresponding to the reduction and oxidation reactions between the Ni2+/Ni4+ redox couple.17,18 The absence of a characteristic reduction peak of Mn4+ around 3.2 V indicates that the Mn4+ in NCM333 and NCM333/LTP is electrochemically inactive and only improves the structural stability of NCM333.41 As we known, the redox peak of Co3+/Co4+ appears at a higher voltage than 4.6 V (the upper limit of voltage in the present study is 4.5 V). So, in the CV curves of NCM333 and NCM333/LTP, no Mn2+/Mn4+ and 10


Page 10 of 31

Page 11 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Co3+/Co4+ redox peaks can be observed. Furthermore, the potential difference value (0.101 V) of the redox peaks of NCM333/LTP is smaller than that of NCM333 (0.130 V), which confirms the lower polarization effect during the electrochemical reaction process for the NCM333/LTP electrode. Therefore, we can conclude that LTP coating may have an admirable impact on the electrochemical performance of NCM333/LTP. Electrochemical impedance spectra (EIS) were measured over a frequency range from 0.01 Hz to 100 kHz to get further insight into the kinetic behavior of both NCM333 and NCM333/LTP. As seen in Figures 6c and d, the two Nyquist plots include a semicircle at high frequency region ascribed to the charge transfer resistance (Rct) between the electrode and electrolyte interface and a straight line at low frequency region corresponding to lithium ion diffusion through the solid electrode.42 Both EIS curves were fitted by using the Zview software (the corresponding equivalent circuit is shown in the insert in Figure 6d). As listed in Table 2, the Rct value of NCM333/LTP (79.12 Ω) is smaller than that of NCM333 (222.40 Ω), indicative of a faster charge transfer for NCM333/LTP. The measured electronic conductivity values for NCM333 and NCM333/LTP are 0.20×10−6 and 4.99×10−6 S cm-1, respectively. The low charge transfer resistance and the high electronic conductivity are positive in enhancing the rate performance of electrode materials. Furthermore, the lithium diffusion coefficient DLi+ can be evaluated from the relationship between Z′ (Z′ is the real part of impedance) and ω-1/2 (ω is the angular frequency) at low frequency according to previous reports.43,44 The Z′ vs. ω−1/2 plots are presented in Figure 6d. The calculated DLi+ values for NCM333 and NCM333/LTP are also listed Table 2. It 11



shows that NCM333/LTP has a higher DLi+ value (1.56×10-13 cm2 s−1) than NCM333 (0.93×10-13 cm2 s−1). Obviously, the LTP coating layer is highly effective for improving the electrochemical reaction environment and thus enhancing the electrochemical performance of NCM333. To study the effect of LTP on the electrochemical performance of NCM333, galvanostatic charge/discharge measurements were carried out between 2.8 and 4.5 V at room temperature and the results are displayed in Figure 7. Figures 7a and b present the initial charge/discharge curves and cycle performance, respectively, for the two samples at 0.5 C. As can be seen in Figure 7a, both samples display similar charge/discharge profiles and only have characteristic charge/discharge platforms for NCM333 between 3.60 and 3.90 V, indicating that LTP is electrochemically inactive during this measured voltage rang (2.8-4.5 V).30,45 It can be also found that NCM333/LTP owns a higher initial discharge capacity of 191.5 mAh g-1 with a columbic efficiency of 91.1% than NCM333 (187.9 mAh g-1, 89.3%) at 0.5 C. The corresponding cycle performance of both samples is presented in Figure 7b and Table 3. It is observed that NCM333/LTP exhibits significantly higher capacity and better cycle performance than NCM333. For example, NCM333/LTP delivers a high capacity of 161.8 mAh g-1 after 100 cycles at 0.5 C, corresponding to a desirable capacity retention ratio of 84.5 %. In sharp contrast, NCM333 shows a gradual capacity fading along with cycling, and the discharge capacity decreases to 135.6 mAh g-1 after 100 cycles with a low capacity retention ratio of 72.1 %. In addition, NCM333 and NCM333/LTP electrodes were also cycled from 0.1 to 4 C and then 12


Page 12 of 31

Page 13 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


back to 0.1 C with 10 cycles per C-rate (shown in Figure 7c). Clearly, as compared with NCM333, NCM333/LTP possesses much higher capacity at any C-rate. For instance, NCM333/LTP delivers a higher average specific capacity (204.9 mAh g-1) than NCM333 (192.5 mAh g-1) at 0.1 C. As the rate increases from 0.5 to 4 C, the specific capacity decreases from 179.5 to 133.4 mAh g-1 for NCM333/LTP, but each value is much larger than that for NCM333 (from 163.1 to 115.9 mAh g-1). To further evaluate the influence of LTP coating on the capability and cyclic performance of NCM333 at a high current rate, charge/discharge measurements at 10 C were performed. As shown in Figure 7d, NCM333/LTP still holds a high initial capacity of 121.0 mAh g-1 with the capacity retention of 82.3 % after 200 cycles at 10 C, while NCM333 only has a slightly lower initial capacity of 120.4 mAh g-1 but a very low capacity retention ratio of 66.4 %. Obviously, the incorporation of LTP can effectively improve the rate capability and cycle performance of NCM333. To help understand the function of LTP in NCM333/LTP, we specially synthesized LTP under the same synthesis condition as NCM333/LTP (described in the Supporting Information section) and test its XRD pattern and CV curve. As clearly seen in the XRD pattern of this as-obtained LTP composite (Figure S1), except for three impurity peaks, the main diffraction peaks can be indexed with the standard LiTi2(PO4)3 (JCPDS, No. 35-0754), which demonstrates that LTP can be successfully obtained under the same synthesis condition as NCM333/LTP. And as shown in the CV curves of LTP (Figure S2), there is no redox peak detected, which reveals that LTP is electrochemical inactive, in other words, LTP will not contribute to the 13



Page 14 of 31

capacity of NCM333/LTP. But as a coating layer with the property of fast ionic conductor,

LTP

may have

influence

on

the

performance

of

NCM333.

The electrochemical performance of pristine and modified NCM333 with different LTP contents is shown in Figure S3. Obviously, when the quantity is insufficient (NCM333/LTP-0.5), the improvement effect is not obvious. When overdose (NCM333/LTP-3), on the one hand, the excess electrochemical inactive LTP will reduce the utilization of active material NCM333; on the other hand, the LTP coating layer will become thicker and hinder ion transmission. When incorporating appropriate amount of LTP (NCM333/LTP-2), the LTP coating layer with suitable thickness can inhibit the side reactions between NCM333 and electrolyte and also is favorable for ion transmission, thus improves the performance of NCM333. So, the roles that the LTP plays in improving the electrochemical performance of NCM333/LTP should be ascribed to its property of fast ionic conductor and the protecting effect of LTP coating layer. 4. CONCLUSIONS LiTi2(PO4)3 coated NCM333 (NCM333/LTP) composite has been successfully prepared via wet chemical method. The effects of LTP coating on the physicochemical properties and electrochemical performance are investigated. The XRD results reveal that both NCM333 and NCM333/LTP have highly layered property and lower cation mixing, and LTP incorporation does not affect on the NCM333 crystal structure. By a combined XPS and TEM analysis, it is found that a LTP layer about 5 nm in thickness is coated on the surface of NCM333. Both the XPS 14


Page 15 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


and magnetic susceptibility results confirm that the valence states of the transition metal elements Ni, Co, Mn, and Ti in NCM333/LTP are +2, +3, +4, and +4, respectively. The electrochemical measurements clearly show that, compared with NCM333, the NCM333/LTP sample presents higher capability and better cycling stability. Such NCM333/LTP electrode exhibits a high initial discharge capacity of 191.5 mAh g-1 with a desirable capacity retention ratio of 84.5 % after 100 cycles at 0.5 C, while NCM333 only has an initial capacity of 187.9 mAh g-1 with a much lower capacity retention ratio of 72.1 %. Even at a high current rate of 10 C, NCM333/LTP still delivers an initial capacity as high as 121.0 mAh g-1 and a desirable capacity retention of 82.3 % after 200 cycles at 10 C, while NCM333 has a lower initial capacity of 120.4 mAh g-1 with a very low capacity retention ratio of 66.4 %. The superior capability and cycling stability of NCM333/LTP may be attributed to the reduced charge transfer resistance, increased electronic conductivity, increased lithium ion diffusion coefficient, and the protecting effect of LTP coating. ASSOCIATED CONTENT Supporting Information The Supporting Information is available free of charge on the ACS Publications website at DOI: Synthesis of LTP, Materials characterization, Electrochemical measurements, XRD pattern of LTP (Figure S1), CV curve of LTP (Figure S2), charge/discharge curves and cycle performance of pristine and modified NCM333 with different LTP contents at 0.5 C (Figure S3) (PDF) 15



AUTHOR INFORMATION Corresponding Author Email: [email protected]. Notes The authors declare no competing financial interest. ACKNOWLEDGMENTS This work was supported by the National Natural Science Foundation of China (51572151, 51772169 and 51672158), the Outstanding Youth Science and Technology Innovation Team Project of Hubei Educational Committee (T201603), and in part by a FRC research grant of Sam Houston State University. References (1) Thackeray, M.M.; Wolverton, C.; Isaacs, E.D. Electrical Energy Storage for Transportation-Approaching the Limits of, and Going Beyond, Lithium-Ion Batteries. Energy & Environ. Sci. 2012, 5, 7854-7863. (2) Sun, Y.K.; Myung, S.T.; Park, B.C.; Prakash, J.; Belharouak, I.; Amine, K. High Energy Cathode Material for Long-Life and Safe Lithium Batteries. Nat. Mater. 2009, 8, 320-324. (3) Zhao, Y.; Li, J.; Dahn, J.R. Inter-Diffusion of Cations from Metal Oxide Surface Coatings into LiCoO2 during Sintering. Chem. Mater. 2017, 29, 5239-5248. (4) Zhang, L.; Peng, G.; Yang, X.; Zhang, P. High Performance LiFePO4/C Cathode for Lithium Ion Battery Prepared under Vacuum Conditions. Vacuum 2010, 84, 1319-1322. 16


Page 16 of 31

Page 17 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


(5) Guo, Z.; Chen, L.; Wang, Y.; Wang, C.; Xia, Y. Aqueous Lithium-Ion Batteries Using Polyimide-Activated Carbon Composites Anode and Spinel LiMn2O4 Cathode. ACS Sustainable Chem. Eng. 2017, 5, 1503-1508. (6) Cho, J.; Kim, Y.J.; Park, B. Novel LiCoO2 Cathode Material with Al2O3 Coating for a Li Ion Cell. Chem. Mater. 2000, 12, 3788-3791. (7) Tukamoto, H.; West, A.R. Electronic Conductivity of LiCoO2 and Its Enhancement by Magnesium Doping. J. Electrochem. Soc. 1997, 144, 3164-3168. (8) Amatucci, G.G.; Tarascona, J.M.; Klein, L.C. Cobalt Dissolution in LiCoO2-Based Non-Aqueous Rechargeable Batteries. Solid State Ionics 1996, 83, 167-173. (9) Ohzuku, T.; Makimura, Y. Layered Lithium Insertion Material of LiNi1/2Mn1/2O2: A Possible Alternative to LiCoO2 for Advanced Lithium-Ion Batteries. Chem. Lett. 2001, 30, 744-745. (10) Makkus, R.C.; Hemmes, K.; de Wit, J.H.W. A Comparative Study of NiO ( Li ), LiFeO2, and LiCoO2 Porous Cathodes for Molten Carbonate Fuel Cells. J. Electrochem. Soc. 1994, 141, 3429-3438. (11) Kim, J.M.; Chung, H.T. The First Cycle Characteristics of Li[Ni1/3Co1/3Mn1/3]O2 Charged Up to 4.7 V. Electrochim. Acta 2004, 49, 937-944. (12) Liu, Z.; Yu, A.; Lee, J.Y. Synthesis and Characterization of LiNi1-x-yCoxMnyO2 as the Cathode Materials of Secondary Bateries. J. Power Sources 1999, 81-82, 416-419. 17



Page 18 of 31

(13) Ohzuku, T.; Makimura, Y. Layered Lithium Insertion Material of LiNi1/3Co1/3Mn1/3O2 for Lithium-Ion Batteries. Chem. Lett. 2001, 7, 642-643. (14) Li, L.; Wang, L.; Zhang, X.; Xie, M.; Wu, F.; Chen, R. Structural and Electrochemical Study of Hierarchical LiNi1/3Co1/3Mn1/3O2 Cathode Material for Lithium-Ion Batteries. ACS Appl. Mater. Interfaces 2015, 7, 21939-21947. (15) Sinha, N.N.; Munichandraiah, N. Synthesis and Characterization of Carbon-Coated

LiNi1/3Co1/3Mn1/3O2

in

a

Single

Step

by

an

Inverse

Microemulsion Route. ACS Appl. Mater. Interfaces 2009, 1, 1241-1249. (16) Zheng, X.; Huang, T.; Pan, Y.; Wang, W.; Fang, G.; Wu, M. High-Voltage Performance of LiNi1/3Co1/3Mn1/3O2/Graphite Batteries with Di(Methylsulfonyl) Methane as a New Sulfone-Based Electrolyte Additive. J. Power Sources 2015, 293, 196-202. (17) Zhao, E.; Chen, M.; Chen, D.; Xiao, X.; Hu, Z. A Versatile Coating Strategy to Highly Improve the Electrochemical Properties of Layered Oxide LiMO2 (M = Ni0.5Mn0.5

and

Ni1/3Mn1/3Co1/3).

ACS

Appl.

Mater.

Interfaces

2015,

7, 27096-27105. (18) Yang, C.; Zhang, X.; Huang, M.; Huang, J.; Fang, Z. Preparation and Rate Capability of Carbon Coated LiNi1/3Co1/3Mn1/3O2 as Cathode Material in Lithium Ion Batteries. ACS Appl. Mater. Interfaces 2017, 9, 12408-12415. (19) Li, X.; He, W.; Chen, L.; Guo, W.; Chen, J.; Xiao, Z. Hydrothermal Synthesis and Electrochemical Performance Studies of Al2O3-Coated LiNi1/3Co1/3Mn1/3O2 for Lithium-Ion Batteries. Ionics 2014, 20, 833-840. 18


Page 19 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


(20) Lu, J.; Peng, Q.; Wang, W.; Nan, C.; Li, L.; Li, Y. Nanoscale Coating of LiMO2 (M = Ni, Co, Mn) Nanobelts with Li+-Conductive Li2TiO3: Toward Better Rate Capabilities for Li-Ion Batteries. J. Am. Chem. Soc. 2013, 135, 1649-1652. (21) Li, J.; Zhang, Q.; Liu, C.; He, X. ZrO2 Coating of LiNi1/3Co1/3Mn1/3O2 Cathode Materials for Li-Ion Batteries. Ionics 2009, 15, 493-496. (22) Li, J.; Fan, M.; He, X.; Zhao, R.; Jiange, C.; Wan, C. TiO2 Coating of LiNi1/3Co1/3Mn1/3O2 Cathode Materials for Li-Ion Batteries. Ionics 2006, 12, 215-218. (23) Myung, S.T.; Lee, K.S.; Yoon, C.S.; Sun, Y.K.; Amine, K.; Yashiro, H. Effect of AlF3

Coating

on

Thermal

Behavior

of

Chemically

Delithiated

Li0.35[Ni1/3Co1/3Mn1/3]O2. J. Phys. Chem. C 2010, 114, 4710-4718. (24) Wang, J.H.; Wang, Y.; Guo, Y.Z.; Ren, Z.Y.; Liu, C.W. Effect of Heat-Treatment on the Surface Structure and Electrochemical Behavior of AlPO4-Coated LiNi1/3Co1/3Mn1/3O2 Cathode Materials. J. Mater. Chem. A 2013, 1, 4879-4884. (25) Kim, H.S.; Kim, K.T.; Kim, Y.S.; Martin, S.W. Effect of a Surface Treatment for LiNi1/3Co1/3Mn1/3O2 Cathode Material in Lithium Secondary Batteries. Met. Mater. Int. 2008, 14, 105-109. (26) Weng, G.M.; Tam, L.Y.S.; Lu, Y.C. High-Performance LiTi2(PO4)3 Anode for High-Areal-Capacity Flexible Aqueous Lithium-Ion Batteries. J. Mater. Chem. A 2017, 5, 11764-11771.

19



Page 20 of 31

(27) Liu, L.; Zhou, M.; Wang, G.; Guo, H.; Tian, F.; Wang, X. Synthesis and Characterization of LiTi2(PO4)3/C Nanocomposite as Lithium Intercalation Electrode Materials. Electrochim. Acta 2012, 70, 136-141. (28) Luo, X.; Wang, X.; Liao, L.; Wang, X.; Gamboa, S.; Sebastian, P. J. Effects of Synthesis Conditions on the Structural and Electrochemical Properties of Layered Li[Ni1/3Co1/3Mn1/3]O2 Cathode Material via the Hydroxide Co-Precipitation Method LIB Scitech. J. Power Sources 2006, 161, 601-605. (29) Riley, L.A.; Atta, S.V.; Cavanagh, A.S.; Yan, Y.; George, S.M.; Liu, P.; Dillon, A.C.; Lee, S.H. Electrochemical Effects of ALD Surface Modification on Combustion Synthesized LiNi1/3Mn1/3Co1/3O2 as a Layered-Cathode Material. J. Power Sources 2011, 196, 3317-3324. (30) Lv, D.; Wang, L.; Hu, P.; Sun, Z.; Chen, Z.; Zhang, Q.; Cheng, W.; Ren, W.; Bian, L.; Xu, J.; Chang, A. Li2O-B2O3-Li2SO4 Modified LiNi1/3Co1/3Mn1/3O2 Cathode Material for Enhanced Electrochemical Performance. Electrochim. Acta 2017, 247, 803-811. (31) Chen, Z.; Wang, J.; Chao, D.; Baikie, T.; Bai, L.; Chen, S.; Zhao, Y.; Sum, T.C.; Lin, J.; Shen, Z. Hierarchical Porous LiNi1/3Co1/3Mn1/3O2 Nano-/Micro Spherical Cathode Material: Minimized Cation Mixing and Improved Li+ Mobility for Enhanced Electrochemical Performance. Sci. Rep. 2016, 6, 25771. (32) Manikandan, P.; Periasamy, P.; Jagannathan, R. Faceted Shape-Drive Cathode Particles

Using

Mixed

Hydroxy-Carbonate

Precursor

20


for

Mesocarbon

Page 21 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Microbeads Versus LiNi1/3Co1/3Mn1/3O2 Li-Ion Pouch Cell. J. Power Sources 2014, 245, 501−509. (33) Zheng, H.; Chen, X.; Yang, Y.; Li, L.; Li, G.; Guo, Z.; Feng, C. Self-Assembled LiNi1/3Co1/3Mn1/3O2 Nanosheet Cathode with High Electrochemical Performance. ACS Appl. Mater. Interfaces 2017, 9, 39560-39568. (34) Liu, G.; Kong, L.; Yan, J.; Liu, Z.; Zhang, H.; Lei, P.; Xu, T.; Mao, H. K.; Chen, B. Nanocrystals in Compression: Unexpected Structural Phase Transition and Amorphization Due to Surface Impurities. Nanoscale 2016, 8, 11803-11809. (35)

Hwang,

B.J.;

Tsai,

Y.W.;

Carlier,

D.;

Ceder,

G.

A

Combined

Computational/Experimental Study on LiNi1/3Co1/3Mn1/3O2. Chem. Mater. 2003, 15, 3676-3682. (36) Oh, S.W.; Park, S.H.; Park, C.W.; Sun, Y.K. Structural and Electrochemical Properties of Layered Li[Ni0.5Mn0.5]1-xCoxO2 Positive Materials Synthesized by Ultrasonic Spray Pyrolysis Method. Solid State Ionics 2004, 171, 167-172. (37) Sun, J.; Sun, Y.; Gai, L.; Jiang, H.; Tian, Y. Carbon-Coated Mesoporous LiTi2(PO4)3 Nanocrystals with Superior Performance for Lithium-Ion Batteries. Electrochim. Acta 2016, 200, 66-74. (38) Kong, J.Z.; Ren, C.; Jiang, Y.X.; Zhou, F.; Yu, C.; Tang, W.P.; Li, H.; Ye, S.Y.; Li, J.X. Li-Ion-Conductive Li2TiO3-Coated Li[Li0.2Mn0.51Ni0.19Co0.1]O2 for High-Performance Cathode Material in Lithium-Ion Battery. J. Solid State Electrochem. 2016, 20, 1435-1443.

21



Page 22 of 31

(39) Hashem, A.M.; Abdel-Ghany, A.E.; Abuzeid, H.M.; Ehrenberg, H.; Mauger, A.; Groult, H.; Julien, C.M. LiNi1/3Mn1/3Co1/3O2 Synthesized by Sol-Gel Method: Structure and Electrochemical Properties. ECS Trans. 2013, 50, 91-96. (40)

Mauger,

A.;

Gendron,

F.;

Julien,

C.M.;

Magnetic

Properties

of

LixNiyMnyCo1−2yO2 (0.2 ≤ 1-2y ≤ 0.5, 0 ≤ x ≤ 1). J. Alloys and Compd. 2012, 520, 42-51. (41) Cabelguen, P.E.; Peralta, D.; Cugnet, M.; Maillet, P. Impact of Morphological Changes of LiNi1/3Mn1/3Co1/3O2 on Lithium-Ion Cathode Performances. J. Power Sources 2017, 346, 13-23. (42) Zhang, L.L.; Li, Z.; Yang, X.L.; Ding, X.K.; Zhou, Y.X.; Sun, H.B.; Tao, H.C.; Xiong, L.Y.; Huang, Y.H. Binder-Free Li3V2(PO4)3/C Membrane Electrode Supported on 3D Nitrogen-Doped Carbon Fibers for High-Performance Lithium-Ion Batteries. Nano Energy 2017, 34, 111-119. (43)

Rao,

C.V.;

Reddy,

LiNi1/3Co1/3Mn1/3O2/Graphene

A.L.M.; Composite

Ishikawa, as

a

Y.;

Ajayan,

Promising

P.M.

Cathode

for

Lithium-Ion Batteries. ACS Appl. Mater. Interfaces 2011, 3, 2966-2972. (44) Liu, X.; Li, H.; Li, D.; Ishida, M.; Zhou, H. PEDOT Modified LiNi1/3Co1/3Mn1/3O2 with Enhanced Electrochemical Performance for Lithium Ion Batteries. J. Power Sources 2013, 243, 374-380. (45) Dang, R.; Chen, M.; Lee, Y.; Cheng, Y.; Xue, L.; Hu, Z.; Xiao, X.; Huang, X. Lithium Ion Conductor and Electronic Conductor Co-Coating Modified Layered Cathode Material LiNi1/3Mn1/3Co1/3O2. Electrochim. Acta 2017, 247, 443-450. 22


Page 23 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Table 1 Lattice parameters of NCM333 and NCM333/LTP samples Sample

a (Å)

c (Å)

c/a

Rp (%)

Rwp (%)

NCM333

2.866

14.26

4.9756

3.12

3.97

NCM333/LTP

2.863

14.25

4.9773

3.21

4.24

Table 2 The EIS fitting results and electronic conductivity of samples Samples

Rct (Ω)

DLi+ (cm2 s−1)

Electronic conductivity (S cm-1)

NCM333

222.40

0.93×10-13

0.20×10−6

NCM333/LTP

79.12

1.56×10-13

4.99×10−6

Table 3 Discharge capacity and capacity retention ratio at 0.5 C of samples.

Discharge capacity (mAh g-1)

Capacity retention ratio

Sample 1st

100th

(%)

NCM333

187.9

135.6

72.1

NCM333/LTP

191.5

161.8

84.5

23



Figure 1 (a) Schematic illustration of the synthesis route for NCM333/LTP, (b-d) XRD patterns and the corresponding Rietveld refinement results of NCM333 and NCM333/LTP, and (e) schematic microstructure of NCM333.

24


Page 24 of 31

Page 25 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Figure 2 SEM images of samples: (a,b) NCM333, (c,d) NCM333/LTP; and (e) particle size distribution of samples.

25



Figure 3 TEM images of samples: (a) NCM333, (b-d) NCM333/LTP; and (e,f) EDS mapping of NCM333/LTP.

26


Page 26 of 31

Page 27 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Figure 4 (a) The full XPS spectra of NCM333 and NCM333/LTP; the high-resolution XPS spectra of samples: (b-d) NCM333, and (e-h) NCM333/LTP.

27



Figure 5 Temperature dependence of magnetic susceptibility χ(T) and reciprocal magnetic susceptibility χ-1(T) for samples: (a) NCM333, and (b) NCM333/LTP.

28


Page 28 of 31

Page 29 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Figure 6 (a,b) CV curves of NCM333 and NCM333/LTP, respectively; and (c,d) EIS spectra and the corresponding relationships between Z′ and ω−1/2 at low frequency region of NCM333 and NCM333/LTP electrodes.

29



Figure 7 Electrochemical performance of samples: (a,b) the initial charge/discharge profiles and cycle performance at 0.5 C, (c) the rate performance profiles of NCM333 and NCM333/LTP at different rates, and (d) the cycle performance of NCM333 and NCM333/LTP at 10 C.

30


Page 30 of 31

Page 31 of 31


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 31


Enhanced Electrochemical Performance of Fast ... - ACS Publications

Recommend Documents