Metal Nitrate Catalysis for Selective Oxidation of 5

This is an open access article published under an ACS AuthorChoice License, which permits copying and redistribution of the article or any adaptations for non-commercial purposes.

Article Cite This: ACS Omega 2019, 4, 7054−7060

http://pubs.acs.org/journal/acsodf

Metal Nitrate Catalysis for Selective Oxidation of 5‑Hydroxymethylfurfural into 2,5-Diformylfuran under Oxygen Atmosphere Mei Hong,*,†,‡ Jie Min,‡ Shuangyan Wu,‡ Huangui Cui,‡ Yuxin Zhao,‡ Jiatong Li,‡ and Shifa Wang†,‡ Jiangsu Co-Innovation Center of Efficient Processing and Utilization of Forest Resources and ‡College of Chemical Engineering, Nanjing Forestry University, Nanjing 210037, People’s Republic of China

ACS Omega 2019.4:7054-7060. Downloaded from pubs.acs.org by 146.185.201.242 on 04/18/19. For personal use only.

†

ABSTRACT: Selective synthesis of various versatile compounds from biomass is of great importance to displace traditional fossil fuel resources. Here, homogeneous metal nitrate (M(NO3)x)/ (2,2,6,6-tetramethylpiperidin-1-yl)oxyl (TEMPO) and M(NO3)x/ TEMPO/NaNO2 catalyst systems in glacial acetic acid and acetonitrile, respectively, have been found to be highly active and practically sustainable for selective oxidation of 5-hydroxymethylfurfural (HMF) into 2,5-diformylfuran (DFF) using pure O2 or even O2 in air as the oxidant. The catalytic methods enable full HMF conversion with a nearly 100% DFF selectivity at 50 °C under atmospheric pressure using a very simple reaction setup and workup. Mechanistic aspects are discussed. The influences of reaction conditions such as different metal catalysts, catalyst loading, solvents, and reaction temperature on the promotion effect were studied. Meanwhile, the catalyst systems had also good performance for aerobic oxidation of other alcohols.

■

INTRODUCTION Biomass was considered by experts as the only renewable source of energy, and it had the potential to replace petroleum in manufacturing chemicals and liquid transportation fuels.1−5 Conversion of bio-sourced saccharides to high value-added chemicals has attracted much attention in recent years.6−8 As an important bio-based platform chemical, 5-hydroxymethylfurfural (HMF) can be converted to various high value-added products through a variety of reactions including hydrogenation, oxidation, and hydration.9−13 2,5-Diformylfuran (DFF) is produced by selective oxidation of HMF14−17 that can be used, for example, as a starting material for the synthesis of diverse poly-Schiff bases, polymer resin sealants, macrocyclic ligands, pharmaceuticals, organic conductors, and the crosslinking agent of poly(vinyl alcohol) for battery separations.18 Recently, chemists had paid much attention on the synthesis of DFF from HMF oxidation using molecular oxygen as the terminal oxidant catalyzed by homogeneous or heterogeneous metal catalysts, such as Ru,19−22 Au,23,24 Cu,25 Mn,26,27 Mo/ V,28 and V.29−31 Most present protocols require the use of noble metals,19−24 expensive ancillary ligands,25 high oxygen pressure (up to 10 bar),30 and/or high reaction temperatures (up to 140 °C)26−29,31 to ensure desirable DFF selectivities at high HMF conversions. There is a need for cheaper, milder, and greener methodologies by designing inexpensive catalytic systems for selective aerobic oxidation of HMF to DFF. Accordingly, TEMPO and its analogues (N-oxyl radical catalysts) have been investigated for reaction components. However, because of the inertness of dioxygen, TEMPO alone is not able to directly catalyze the oxidation of alcohols using dioxygen as the terminal oxidant, so it is necessary to use a cocatalyst to activate dioxygen and transfer its oxidizability to © 2019 American Chemical Society

the next redox cycle of TEMPO. The catalysts such as HNO3immobilized TEMPO and TEMPO-imidazolium salts can efficiently and selectively catalyze the oxidation of alcohols to the corresponding aldehydes or ketones.32,33 However, there are only a few reported studies on applying N-oxyl radicals to catalyze the oxidation of HMF.34,35 Yang et al.36 reported that benzoic acid/TEMPO obtained 86.7% conversion of HMF and 77.8% yield of DFF at 0.4 MPa O2 in acetonitrile. Although interesting achievement was obtained by this method in the field of aerobic oxidation of HMF into DFF, it required relatively high operating pressures (0.4 MPa), high catalyst loading (50 mol %), special Teflon-lined autoclave reactors, high temperatures (up to 100 °C), and long reaction time (24 h). Motivated by a desire to develop better aerobic oxidation catalysts, especially stressing the function of air oxygen in these transformations, we now describe an efficient and selective oxidation of HMF to DFF by using two novel cost-beneficial catalytic systems based on M(NO3)x/TEMPO and M(NO3)x/ TEMPO/NaNO2 under mild, aerobic conditions (Scheme 1). The oxidations were carried out in glacial acetic acid and acetonitrile solution under the same conditions.

■

RESULTS AND DISCUSSION Our study commenced with screening the transformation of HMF to DFF in the presence of different metal nitrates using molecular oxygen as the oxidant. We initially tried this aerobic oxidation of HMF using 5 mol % Fe(NO3)3·9H2O and 5 mol % TEMPO as catalysts in glacial acetic acid as it is a good Received: February 13, 2019 Accepted: April 11, 2019 Published: April 18, 2019 7054

DOI: 10.1021/acsomega.9b00391 ACS Omega 2019, 4, 7054−7060

ACS Omega

Article

1, entry 9). The surprising result may be due to the identical amount of NO3− in Fe(NO3)3·9H2O and Al(NO3)3. To test the hypothesis, we increased the amount of the catalysts Cu(NO3)2·3H2O, Zn(NO3)2·6H2O, HNO3, KNO3, and NaNO3. It was easily found in Table 1 that conversions of the aerobic oxidation were in proportion to the amount of NO3−. The efficiency of HNO3 or other metals (Cu, Zn) containing nitrates as a viable alternative to Fe(NO3)3·9H2O was also quite surprising (Table 1, entries 8, 11, and 17). By employing 15 mol % NO3− in combination of TEMPO, 100% HMF conversion was obtained within 5 h with the highest DFF yield of 99%, which was complete oxidations. As far as we are aware, aluminum and zinc were applied here for the first time to mediate efficiently the TEMPO-catalyzed aerobic selective oxidation of HMF to DFF. The observation that Al(NO3)3·9H2O and Zn(NO3)3·6H2O, which contain redoxinactive Al and Zn, are competent catalysts demonstrates that a redox change at the metal is not necessary for HMF oxidation.39 Alkali-metal nitrates such as sodium nitrate and potassium nitrate presented less catalytic activity (Table 1, entries 12−15). The results indicated that the metal cation also has some influence on the reaction, and the active species in the M(NO3)x/TEMPO catalytic system, maybe, is not the free nitrosonium ion but the metal−TEMPO complex.39 The coordination of TEMPO to a Lewis acid makes TEMPO a better oxidant. We suggested that the transformation proceeds via a mechanism involving concerted proton-coupled electron transfer from the C−H bond of HMF to the nitrogen atom of the metal−TEMPO complex.40,41 Controlled experiments with or without TEMPO confirmed their necessity to obtain a desired outcome of the reaction. When Fe(NO3)3·9H2O was used without TEMPO, only little HMF was oxidized (Table 2, entry 1), indicating that TEMPO

Scheme 1. Oxidation of HMF into DFF

solvent for the homogeneous system of the oxidation of alcohols to aldehydes,37,38 and this reaction could work smoothly at room temperature under atmospheric pressure of molecular oxygen affording DFF in 93% yield after 8 h (Table 1, entry 1). Oxygen was simply flushed into a balloon Table 1. Effect of Different Catalysts on HMF Conversion and DFF Yield in AcOHa entry 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

catalyst, loading (mol %) Fe(NO3)3·9H2O, 5 Fe(NO3)3·9H2O, 5 Fe(NO3)3·9H2O, 2 Fe(acac)3, 5 FeCl3·6H2O, 5 Cu(NO3)2·3H2O, 5 Cu(NO3)2·3H2O, 7.5 Al(NO3)3·9H2O, 5 Zn(NO3)2·6H2O, 5 Zn(NO3)2·6H2O, 7.5 KNO3, 10 KNO3, 15 NaNO3, 10 NaNO3, 15 HNO3, 5 HNO3, 15

T (°C)

time (h)

conv. HMF (%)

yield DFF (%)

select.b (%)

RT 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50

8 5 5 5 24 24 5 5 5 5 5 5 5 5 5 5 5

100 100 84 2 2 2 81 100 95 78 100 49 64 51 64 72 100

93 95 78 1 1 1 80 99 93 72 97 57 61 49 62 71 98

93 95 93 50 50 50 99 99 98 92 97 96 95 96 97 99 98

Table 2. Effect of Cocatalysts and Oxidants on HMF Conversion and DFF Yield in AcOHa entry 1 2 3 4 5 6 7 8

a

Reaction conditions: HMF (1 mmol, 126 mg), TEMPO (0.05 mmol, 7.8 mg), 50 °C, AcOH (2 mL), and oxygen balloon; the conversion and yield were determined by HPLC. Conv. = conversion. Select. = selectivity. bS (DFF) = yield (DFF)/conversion (HMF).

and attached to a flask containing a solution of HMF. To shorten the reaction time, the reaction temperature was raised to 50 °C (Table 1, entry 2). Under lower Fe(NO3)3·9H2O loading at 2 mol %, 78% yield of DFF was achieved (Table 1, entry 3). Only a trace amount of the product was detected in a control experiment without the Fe(NO3)3·9H2O catalyst (Table 1, entry 4). To examine the role of iron in the reaction, we selected two trivalent iron salts. In sharp contrast, HMF was almost not oxidized when Fe(acac)3 and FeCl3· 6H2O were used instead of Fe(NO3)3·9H2O (Table 1, entries 5 and 6), indicating NO3− played a critical role for the aerobic oxidation of HMF. Subsequently, a series of inorganic nitrates were investigated to test whether the metal cation also had a certain effect for the reaction. We observed that all nitrates and nitric acid successfully catalyzed the conversion, and Al(NO3)3·9H2O worked only as well as Fe(NO3)3·9H2O (Table

cocatalyst, loading (mol %) TEMPO, TEMPO, TEMPO, TEMPO, NHPI, 5

0 2 5 5

oxidant (mmol)

time (h)

conv. HMF (%)

yield DFF (%)

select.b (%)

O2 O2 O2 air O2 DDQ (2) TBHP (2) H2O2 (2)

5 5 5 5 24 24 24 24

17 85 100 82 37 18 46 30

0 69 95 81 3 4 1 0

0 81 95 99 8 22 2 0

a Reaction conditions: HMF (1 mmol, 126 mg), Fe(NO3)3·9H2O (0.05 mmol), 50 °C, AcOH (2 mL), and oxygen balloon; the conversion and yield were determined by HPLC. Conv. = conversion. Select. = selectivity. bS (DFF) = yield (DFF)/conversion (HMF).

participated in the aerobic oxidation. Subsequently, increasing the amount of TEMPO to 2 mol % resulted in a significant increase in terms of the product yield (Table 2, entry 2). Five mole percent TEMPO was enough for complete transformation of HMF to DFF. Air has the obvious advantage of safety and low cost. We next examined the ability of the Fe(NO3)3·9H2O catalyst to catalyze the HMF oxidation using air instead of pure oxygen as the terminal oxidant. To our delight, DFF was still obtained in a high yield of 81% after 5 h, and the selectively of DFF was even higher (Table 2, entry 4). The lower DFF yield with air balloon was due to a lower 7055


ACS Omega

Article

nevertheless, when HMF was set at a lower concentration of 0.5 mol/L under the same conditions, full conversion was achieved (Table 3, entry 4), indicating that lowering the HMF concentration, the yields of product DFF can be increased. However, a further reduction in the concentration of HMF to 0.2 mol/L resulted in a lower yield of DFF. To make the workup procedure more simple and apply to substrates containing acid-sensitive functional groups, the catalytic system of Fe(NO3)3/TEMPO was further studied in CH3CN; however, the reaction was much slower (96% of conversion after 24 h) than that in AcOH. Thus, we started to test the effect of additives: The addition of NaNO2 helps much increase in reaction rates (Table 4, entry 2). The result demonstrated that NaNO2 is an activating agent for the iron− TEMPO catalytic system. The cheap and readily available inorganic halide sodium chloride was screened for such a purpose. In our hands, the addition of NaCl (5 mol %) as an additive, as reported by Ma et al.,42 suggests that the reaction was completed within 15 h (Table 4, entry 3). Isobutyl nitrite (C4H9NO2) worked much slower (Table 4, entry 4). In addition, no reaction occurred in the absence of Fe(NO3)3· 9H2O (Table 4, entry 5) or TEMPO under oxygen (Table 4, entry 6), suggesting that both Fe(NO3)3·9H2O and TEMPO are required for the reaction. Then, Fe(acac)3 and FeCl3 were used as catalysts in the catalytic system, and Fe(acac)3 was almost inert for the selective oxidation of HMF (Table 4, entry 7). As for FeCl3, much better conversion (36%) with 100% selectivity was obtained (Table 4, entry 8). For Cu(NO3)2· 3H2O, we found that HMF conversion significantly increased from 62 to 100% with increasing catalyst loading (Table 4, entries 9 and 10). Further experiments with Al(NO3)3·9H2O presented a poorer catalytic activity as compared with the case of AcOH as a solvent (Table 4, entry 11). Increasing the amount of Zn(NO3)2·6H2O led to slight conversion of HMF (Table 4, entries 12 and 13). KNO3 and NaNO3 were not effective at all for the oxidation of HMF (Table 4, entries 14 and 15). These results clearly showed that employing redoxactive metals such as Fe and Cu had a better effect on the reaction outcome in CH3CN. On the basis of the results of this experiment and the previous reports,43 a plausible reaction pathway is illustrated in Scheme 2. In this proposed

concentration of oxygen. The catalytic efficiency of other stable N-oxyl radical such as N-hydroxyphthalimide (NHPI) replaced TEMPO with 5 mol % Fe(NO3)3·9H2O in AcOH under an oxygen atmosphere at 50 °C, however, exhibited a very small amount of HMF conversion (Table 2, entry 5). Importantly, if other common oxidants such as 2,3-dichloro-5,6-dicyano-1,4benzoquinone (DDQ), t-BuOOH (TBHP), and H2O2 were used instead of TEMPO and oxygen, HPLC analysis of the products after 24 h of reaction revealed the further oxidation into 2,5-furandicarboxylic acid (FDCA) (14% yield at 18% HMF conversion, 45% yield at 46% HMF conversion, and 30% yield at 30% HMF conversion). It is known that the solvent is a key factor affecting the reaction efficiency. Thus, the aerobic oxidation of HMF to DFF was carried out in a variety of common solvents such as ethyl acetate (EtOAc) and 1,2-dichloroethane (DCE), which have been used in related alcohol oxidation methods. As shown in Table 3, the solvent showed a remarkable effect on DFF Table 3. Effect of the Solvent and HMF Concentration on HMF Conversion and DFF Yield with Fe(NO3)3/TEMPO Catalyst Systema entry

solvent

solvent amount (mL)

conv. HMF (%)

yield DFF (%)

select.b (%)

1 2 3 4 5

EtOAc DCE AcOH AcOH AcOH

2 2 1 2 5

100 100 62 100 58

57 64 61 95 52

57 64 98 95 90

a Reaction conditions: HMF (1 mmol, 126 mg), Fe(NO3)3·9H2O (0.05 mmol), TEMPO (0.05 mmol, 7.8 mg), 50 °C, 5 h, and oxygen balloon; the conversion and yield were determined by HPLC. Conv. = conversion. Select. = selectivity. bS (DFF) = yield (DFF)/conversion (HMF).

selectivity. Low DFF selectivity was obtained when the reaction was carried out in EtOAc and DCE (Table 3, entries 1 and 2). The concentration of HMF can also have some effects on the conversion of HMF during the oxidation process. When the concentration of HMF was 1 mol/L, after reaction for 5 h, the yield of product DFF was 61% (Table 3, entry 3);

Table 4. Effect of Different Catalysts on HMF Conversion and DFF Yield in CH3CNa entry 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

catalyst, loading (mol %) Fe(NO3)3·9H2O, Fe(NO3)3·9H2O, Fe(NO3)3·9H2O, Fe(NO3)3·9H2O,

5 5 5 5

Fe(NO3)3·9H2O, 5 Fe(acac)3, 5 FeCl3·6H2O, 5 Cu(NO3)2·3H2O, 5 Cu(NO3)2·3H2O, 7.5 Al(NO3)3·9H2O, 5 Zn(NO3)2·6H2O, 5 Zn(NO3)2·6H2O, 7.5 NaNO3, 5 KNO3, 5

cocatalyst TEMPO TEMPO TEMPO TEMPO TEMPO TEMPO TEMPO TEMPO TEMPO TEMPO TEMPO TEMPO TEMPO TEMPO

additive

time (h)

conv. HMF (%)

yield DFF (%)

select.b (%)

NaNO2 NaCl C4H9NO2 NaNO2 NaNO2 NaNO2 NaNO2 NaNO2 NaNO2 NaNO2 NaNO2 NaNO2 NaNO2 NaNO2

24 10 15 24 24 24 24 24 10 10 10 10 10 10 10

96 100 99 58 NR NR 2 36 62 100 77 61 68 5 2

91 94 98 58

95 94 98 100

0 36 61 99 77 60 65 1 1

0 100 98 99 100 98 96 20 50

Reaction conditions: HMF (1 mmol, 126 mg), additive (0.05 mmol), CH3CN (5 mL), 50 °C, and oxygen balloon. NR = no reaction. The conversion and yield were determined by HPLC. Conv. = conversion. Select. = selectivity. bS (DFF) = yield (DFF)/conversion (HMF).

a

7056


ACS Omega

Article

Scheme 2. Proposed Catalytic Cycle for Aerobic Oxidation of HMF with M(NO3)x/TEMPO/NaNO2

Table 6. Effect of Reaction Temperature on HMF Conversion and DFF Yield in CH3CNa entry

temperature (°C)

conv. HMF (%)

yield DFF (%)

select.b (%)

1 2 3 4 5 6

RT 30 40 50 60 70

16 57 72 100 54 28

15 55 69 94 52 27

94 96 95 94 96 96

Reaction conditions: HMF (1 mmol, 126 mg); Fe(NO3)3·9H2O (0.05 mmol), TEMPO (0.05 mmol, 7.8 mg), NaNO2 (0.05 mmol, 3.4 mg), CH3CN (5 mL), and oxygen balloon; the conversion and yield were determined by HPLC. Conv. = conversion. Select. = selectivity. b S (DFF) = yield (DFF)/conversion (HMF). a

mechanism, by the oxidation action of FeIII or CuII, TEMPO is transformed into a nitrogen carbonyl cation by a singleelectron oxidation, and this cation extracts a hydrogen atom from HMF to transform it to DFF. Furthermore, TEMPO is restored to its original state, whereas the FeIII or CuII ion is reduced to the FeII or CuI ion. At the same time, the NO3− ion oxidizes the FeII or CuI ion to the FeIII or CuII ion, whereas the NO3− ion is reduced to the NO2− ion. In the meantime, molecular oxygen again oxidizes the NO2− ion, and the NO3− ion is thus restored. Switching from pure oxygen to air and using the same atmospheric pressure also gave the oxidized product DFF in 88% yield after 10 h (Table 5, entry 1). NHPI provided a low

sharp decline in HMF conversion (Table 6, entries 5 and 6). It could be concluded that the higher temperature (above 50 °C) could result in a negative effect, and 50 °C was the preferred temperature for the Fe(NO3)3/NaNO2/TEMPO catalytic system. Importantly, the selectivity to DFF remained at a relatively constant and high level (>94%) while the reaction temperatures were varied. The decline in the yield of DFF over 50 °C may possibly be attributed to the mass transfer resistance of oxygen from oxygen gas on the liquid surface down to the liquid solution. Larger mass transfer resistance of oxygen makes the concentration of oxygen lower, and as a consequence, fewer HMF molecules will be successfully transformed into DFF. The solvent effect of the aerobic oxidation reaction at 50 °C was examined to select an industrial friendly solvent. The results of the oxidation of HMF in the presence of 5 mol % Fe(NO3)3·9H2O, 5 mol % TEMPO, and 5 mol % NaNO2 under the atmospheric pressure of oxygen in different solvents are summarized in Table 7. We were delighted to find that

Table 5. Effect of Cocatalysts and Oxidants on HMF Conversion and DFF Yield in CH3CNa entry 1 2 3 4 5

cocatalyst, loading (mol %) TEMPO, 5 NHPI, 5

oxidant

time (h)

conv. HMF (%)

yield DFF (%)

select.b (%)

air O2 DDQ H2O2 TBHP

10 24 10 24 24

89 57 32 11 64

88 54 19 6 58

99 95 59 55 91

Table 7. Effect of the Solvent and HMF Concentration on HMF Conversion and DFF Yield with Fe(NO3)3/NaNO2/ TEMPO Catalyst System Conditionsa

Reaction conditions: HMF (1 mmol, 126 mg); Fe(NO3)3·9H2O (0.05 mmol), NaNO2 (0.05 mmol, 3.4 mg), CH3CN (5 mL), and 50 °C; the conversion and yield were determined by HPLC. Conv. = conversion. Select. = selectivity. bS (DFF) = yield (DFF)/conversion (HMF). a

conversion under our reaction conditions compared with the reported literature (Table 5, entry 2).44 These results demonstrated that the catalytic activity of NHPI was not so effective to selectively oxidize HMF to DFF under the present reaction conditions. Both HMF conversion and the selectivity of DFF were low using H2O2 as an oxidant (Table 5, entry 4). Moderate HMF conversion and the DFF yield were obtained using t-BuOOH as an oxidant (Table 5, entry 5), which was different from the reaction in AcOH. To further investigate the catalytic performance of Fe(NO3)3/TEMPO/NaNO2, aerobic oxidations with different temperatures were carried out in acetonitrile. As shown in Table 6, it was observed that temperature played an important role in the oxidation of HMF in acetonitrile. As expected, HMF conversion and the DFF yield increased with the increase of reaction temperature from room temperature to 50 °C (Table 6, entries 1−4), but a rise over 50 °C resulted in a

entry

solvent

solvent amount (mL)

conv. HMF (%)

yield DFF (%)

select.b (%)

1 2 3 4 5 6 7

H2O EtOAc DCE MeCN MeCN MeCN

5 5 5 5 2 1

55 3 100 100 100 100 80

51 3 98 93 94 96 77

93 100 98 93 94 96 96

a Reaction conditions: HMF (1 mmol, 126 mg), Fe(NO3)3·9H2O (0.05 mmol, 20 mg), TEMPO (0.05 mmol, 7.8 mg), NaNO2 (0.05 mmol, 3.4 mg), 50 °C, 10 h, and oxygen balloon; the conversion and yield were determined by HPLC. Conv. = conversion. Select. = selectivity. bS (DFF) = yield (DFF)/conversion (HMF).

when using ethyl acetate as the solvent, HMF could be converted into DFF within 10 h in an almost quantitative yield of 98%. Therefore, ethyl acetate is also a desired solvent. Under the same conditions, the conversion of HMF to DFF was achieved in a high yield in 1,2-dichloroethane. However, such an environmentally unfriendly chlorinated solvent is disfavored for large-scale industrial application. The effect of the substrate concentration on the conversion of HMF and the yield/selectivity of DFF is shown in Table 7. As the substrate 7057


ACS Omega

Article

Table 8. Aerobic Fe(NO3)3/TEMPO-Catalyzed Oxidation of Various Alcohols

Conditions A: substrate (1 mmol), Fe(NO3)3·9H2O (0.05 mmol), TEMPO (0.05 mmol), 50 °C, AcOH (2 mL), and oxygen balloon. Conditions B: substrate (1 mmol), Fe(NO3)3·9H2O (0.05 mmol, 20 mg), TEMPO (0.05 mmol), NaNO2 (0.05 mmol, 3.4 mg), CH3CN (5 mL), 50 °C, 10 h, and oxygen balloon. bConversions and yields are based on gas chromatography (GC) with area normalization. NR = no reaction. Conv. = conversion. a

thus serving as a potentially greener alternative to the classical transformations.

concentration increased from 0.2 mol/L to 0.5 mol/L, almost no change was observed in the DFF yield (Table 7, entries 5 and 6). As the concentration of HMF was further increased to 1 mol/L, the conversion of HMF decreased to 80%, which is most likely due to the evaporation of CH3CN and the mass transfer of the entire system being restricted by the increase in the substrate concentration. The two catalyst systems were applied to the aerobic oxidation of a variety of alcohols. As shown in Table 8, all benzylic alcohols were quantitatively converted into the corresponding aldehydes with >99% selectivity with both of the catalyst systems. Secondary alcohols including cyclohexanol and diphenylmethanol can be completely converted into corresponding ketones with >99% selectivity with the Fe(NO3)3/TEMPO/NaNO2 catalytic system in CH3CN, whereas the secondary aliphatic alcohol cyclohexanol was failed to afford the desired product with the Fe(NO3)3/ TEMPO catalytic system in AcOH. 1,2-Diols seldom interfered with the catalytic aerobic oxidation were selectivity oxidized into ketone and aldehyde. 1,2-Diol was cleanly oxidized to α-dicarbonyl without cleavage of the 1,2-diol bond with the Fe(NO3)3/TEMPO/NaNO2 catalytic system in CH3CN. Fe(NO3)3/TEMPO was catalyzed aerobic cleavage of 1-phenyl-1,2-ethanediol into benzoic acid in the quantitative yield in AcOH. The stoichiometric oxidants that are still predominantly used for such oxidative cleavage, such as H5IO6, Pb(OAc)4, and KMnO4,45 generate stoichiometric hazardous waste. Herein, we describe an applicable oxidative cleavage of 1,2-diols that consumes atmospheric oxygen as the oxidant,

■

CONCLUSIONS We have developed two novel catalytic systems, including TEMPO and metal nitrates, for the aerobic oxidation of HMF to DFF at 50 °C in the presence of 1 atm O2. Various aliphatic and aromatic alcohols could be oxidized quantitatively to the corresponding carbonyl compounds in the catalytic systems, and pure products are generally isolable by simple extraction with an organic solvent and water. We anticipated that this protocol will be of broad interest and use to the chemical industries.

■

EXPERIMENTAL SECTION

Materials. All chemicals used in this study were of analytical reagent grade, commercially available, and used without further purification unless otherwise noted. Reactions were carried out in 5 or 10 mL glass flasks. HMF and balloons (500 mL) were purchased from Sigma-Aldrich and used as an air reservoir. Reactions were monitored using thin-layer chromatography on TLC silica gel 60 F254 aluminum sheets (20 × 20 cm). Selective Aerobic Oxidation of Alcohols into Aldehydes or Ketones with the M(NO3)x/TEMPO Catalytic System. For a typical procedure, a 5 mL glass flask equipped with a magnetic stirring bar was charged with HMF (126 mg, 1 mmol) and glacial acetic acid (2 mL). Fe(NO3)3·9H2O (20.2 7058


ACS Omega

■

mg, 0.05 mmol) and TEMPO (7.8 mg, 0.05 mmol) were consecutively added to the solution, and a balloon filled with oxygen (500 mL) was then attached to the flask. The reaction mixture was magnetically stirred at 50 °C, and the consumption of the starting material was monitored using TLC. After completion of the reaction, the reaction was quenched by adding EtOAc. The catalyst was removed by washing with water. Aqueous phases were combined and then extracted with EtOAc. The aqueous phase extracts were combined and dried with MgSO4. The solvent was evaporated in vacuo to yield pure products. Selective Aerobic Oxidation of Alcohols into Aldehydes or Ketones with the M(NO3)x/TEMPO/NaNO2 Catalytic System. For a typical procedure, HMF (126 mg, 1 mmol), Fe(NO3)3·9H2O (20.2 mg, 0.05 mmol), TEMPO (7.8 mg, 0.05 mmol), NaNO2 (3.4 mg, 0.05 mmol), and CH3CN (5 mL) were added to a 10 mL glass flask. The resulting mixture was stirred under the atmosphere of oxygen from a balloon at 50 °C until HMF disappeared (as monitored by TLC). Upon completion, the reaction was quenched by adding EtOAc. The catalyst was removed by washing with water. The aqueous phases were combined and extracted with EtOAc. The aqueous phase extracts were then combined and dried with MgSO4. The solvent was evaporated in vacuo to yield pure products. Product Analysis. HMF and DFF were analyzed by HPLC using a reversed-phase C18 column (250 × 4.6 mm) at 25 °C with a detection wavelength of 280 nm. The mobile phase was acetonitrile and 0.1 wt % acetic acid aqueous solution (65:35 v/v) at 0.5 mL/min. The HMF conversion and DFF yield were expressed as mol % in terms of the total HMF amount. The amounts of HMF and DFF in the samples were calculated by interpolation from calibration curves. Calibration curves for the observed products were constructed by injecting known concentrations of reference commercial products. Other alcohols were analyzed using GC (Agilent, GC-7890A) equipped with a flame ionization detector and an Rtx-5 (30 m × 0.32 mm × 0.25 μm) capillary column and further confirmed by GC−MS. GC−MS spectra were performed using an Agilent Technologies 7890A GC system with an Agilent 5975 inert mass selective detector (EI) and an HP-5 MS column (0.25 mm × 30 m, film: 0.25 μm).

■

Article

REFERENCES

(1) Berenguer, A.; Sankaranarayanan, T. M.; Gómez, G.; Moreno, I.; Coronado, J. M.; Pizarro, P.; Serrano, D. P. Evaluation of transition metal phosphides supported on ordered mesoporous materials as catalysts for phenol hydrodeoxygenation. Green Chem. 2016, 18, 1938−1951. (2) Fermoso, J.; Hernando, H.; Jana, P.; Moreno, I.; Přech, J.; Ochoa-Hernández, C.; Pizarro, P.; Coronado, J. M.; Č ejka, J.; Serrano, D. P. Lamellar and pillared ZSM-5 zeolites modified with MgO and ZnO for catalytic fast-pyrolysis of eucalyptus woodchips. Catal. Today 2016, 277, 171−181. (3) Shylesh, S.; Gokhale, A. A.; Scown, C. D.; Kim, D.; Ho, C. R.; Bell, A. T. From sugars to wheels: The conversion of ethanol to 1,3butadiene over metal-promoted magnesia-silicate catalysts. ChemSusChem 2016, 9, 1462−1472. (4) Wang, A.; Balsara, N. P.; Bell, A. T. Pervaporation-assisted catalytic conversion of xylose to furfural. Green Chem. 2016, 18, 4073−4085. (5) Xiao, C.; Goh, T.-W.; Qi, Z.; Goes, S.; Brashler, K.; Perez, C.; Huang, W. Conversion of levulinic acid to γ-Valerolactone over fewlayer graphene-supported ruthenium catalysts. ACS Catal. 2016, 6, 593−599. (6) Hu, L.; Lin, L.; Wu, Z.; Zhou, S.; Liu, S. Recent advances in catalytic transformation of biomass-derived 5-hydroxymethylfurfural into the innovative fuels and chemicals. Renewable Sustainable Energy Rev. 2017, 74, 230−257. (7) Yang, Z.; Qi, W.; Huang, R.; Fang, J.; Su, R.; He, Z. Functionalized silica nanoparticles for conversion of fructose to 5hydroxymethylfurfural. Chem. Eng. J. 2016, 296, 209−216. (8) Yu, I. K. M.; Tsang, D. C. W. Conversion of biomass to hydroxymethylfurfural: A review of catalytic systems and underlying mechanisms. Bioresour. Technol. 2017, 238, 716−732. (9) Gawade, A. B.; Nakhate, A. V.; Yadav, G. D. Selective synthesis of 2, 5-furandicarboxylic acid by oxidation of 5-hydroxymethylfurfural over MnFe2O4 catalyst. Catal. Today 2018, 309, 119−125. (10) Sun, G.; An, J.; Hu, H.; Li, C.; Zuo, S.; Xia, H. Green catalytic synthesis of 5-methylfurfural by selective hydrogenolysis of 5hydroxymethylfurfural over size-controlled Pd nanoparticle catalysts. Catal. Sci. Technol. 2019, 9, 1238−1244. (11) Xia, H.; Xu, S.; Hu, H.; An, J.; Li, C. Efficient conversion of 5hydroxymethylfurfural to high-value chemicals by chemo- and biocatalysis. RSC Adv. 2018, 8, 30875−30886. (12) Román-Leshkov, Y.; Chheda, J. N.; Dumesic, J. A. Phase modifiers promote efficient production of hydroxymethylfurfural from fructose. Science 2006, 312, 1933−1937. (13) Rosatella, A. A.; Simeonov, S. P.; Frade, R. F. M.; Afonso, C. A. M. 5-Hydroxymethylfurfural (HMF) as a building block platform: Biological properties, synthesis and synthetic applications. Green Chem. 2011, 13, 754−793. (14) Artz, J.; Mallmann, S.; Palkovits, R. Selective aerobic oxidation of HMF to 2,5-diformylfuran on covalent triazine frameworkssupported Ru catalysts. ChemSusChem 2015, 8, 672−679. (15) Ma, J.; Du, Z.; Xu, J.; Chu, Q.; Pang, Y. Efficient aerobic oxidation of 5-hydroxymethylfurfural to 2,5-diformylfuran, and synthesis of a fluorescent material. ChemSusChem 2011, 4, 51−54. (16) Neaţu, F.; Petrea, N.; Petre, R.; Somoghi, V.; Florea, M.; Parvulescu, V. I. Oxidation of 5-hydroxymethyl furfural to 2,5diformylfuran in aqueous media over heterogeneous manganese based catalysts. Catal. Today 2016, 278, 66−73. (17) Le, N.-T.; Lakshmanan, P.; Cho, K.; Han, Y.; Kim, H. Selective oxidation of 5-hydroxymethyl-2-furfural into 2,5-diformylfuran over VO2+ and Cu2+ ions immobilized on sulfonated carbon catalysts. Appl. Catal., A 2013, 464-465, 305−312. (18) Amarasekara, A. S.; Green, D.; Williams, L. D. Renewable resources based polymers: Synthesis and characterization of 2,5diformylfuran-urea resin. Eur. Polym. J. 2009, 45, 595−598. (19) Antonyraj, C. A.; Jeong, J.; Kim, B.; Shin, S.; Kim, S.; Lee, K.Y.; Cho, J. K. Selective oxidation of HMF to DFF using Ru/γ-alumina

AUTHOR INFORMATION

Corresponding Author

*E-mail: [email protected]. Tel: +86-25-85427635. Fax: +86-25-85428873. ORCID

Mei Hong: 0000-0002-6098-0368 Notes

The authors declare no competing financial interest.

■

ACKNOWLEDGMENTS This work was financially supported by the Open Foundation of Jiangsu Key Laboratory of Biomass Energy and Materials (JSBEM201915). This work was also financially supported by the Natural Science Foundation of Jiangsu province (grant no. BK20140969) and the Priority Academic Program Development of Jiangsu Higher Education Institutions (PAPD). 7059


ACS Omega

Article

catalyst in moderate boiling solvents toward industrial production. J. Ind. Eng. Chem. 2013, 19, 1056−1059. (20) Nie, J.; Xie, J.; Liu, H. Efficient aerobic oxidation of 5hydroxymethylfurfural to 2,5-diformylfuran on supported Ru catalysts. J. Catal. 2013, 301, 83−91. (21) Takagaki, A.; Takahashi, M.; Nishimura, S.; Ebitani, K. One-pot synthesis of 2,5-diformylfuran from carbohydrate derivatives by sulfonated resin and hydrotalcite-supported ruthenium catalysts. ACS Catal. 2011, 1, 1562−1565. (22) Wang, Y.; Liu, B.; Huang, K.; Zhang, Z. Aerobic oxidation of biomass-derived 5-(hydroxymethyl)furfural into 2,5-diformylfuran catalyzed by the trimetallic mixed oxide (Co-Ce-Ru). Ind. Eng. Chem. Res. 2014, 53, 1313−1319. (23) Zhu, Y.; Shen, M.; Xia, Y.; Lu, M. Au/MnO2 nanostructured catalysts and their catalytic performance for the oxidation of 5(hydroxymethyl)furfural. Catal. Commun. 2015, 64, 37−43. (24) Yang, Z.; Qi, W.; Su, R.; He, Z. Selective synthesis of 2,5Diformylfuran and 2,5-furandicarboxylic acid from 5-hydroxymethylfurfural and fructose catalyzed by magnetically separable catalysts. Energy Fuels 2017, 31, 533−541. (25) Hansen, T. S.; Sádaba, I.; García-Suárez, E. J.; Riisager, A. Cu catalyzed oxidation of 5-hydroxymethylfurfural to 2,5-diformylfuran and 2,5-furandicarboxylic acid under benign reaction conditions. Appl. Catal., A 2013, 456, 44−50. (26) Liu, B.; Zhang, Z.; Lv, K.; Deng, K.; Duan, H. Efficient aerobic oxidation of biomass-derived 5-hydroxymethylfurfural to 2,5-diformylfuran catalyzed by magnetic nanoparticle supported manganese oxide. Appl. Catal., A 2014, 472, 64−71. (27) Yang, Z.-Z.; Deng, J.; Pan, T.; Guo, Q.-X.; Fu, Y. A one-pot approach for conversion of fructose to 2,5-diformylfuran by combination of Fe3O4-SBA-SO3H and K-OMS-2. Green Chem. 2012, 14, 2986−2989. (28) Liu, R.; Chen, J.; Chen, L.; Guo, Y.; Zhong, J. One-step approach to 2,5-diformylfuran from fructose by using a bifunctional and recyclable acidic polyoxometalate catalyst. ChemPlusChem 2014, 79, 1448−1454. (29) Antonyraj, C. A.; Kim, B.; Kim, Y.; Shin, S.; Lee, K.-Y.; Kim, I.; Cho, J. K. Heterogeneous selective oxidation of 5-hydroxymethyl-2furfural (HMF) into 2,5-diformylfuran catalyzed by vanadium supported activated carbon in MIBK, extracting solvent for HMF. Catal. Commun. 2014, 57, 64−68. (30) Sádaba, I.; Gorbanev, Y. Y.; Kegnaes, S.; Putluru, S. S. R.; Berg, R. W.; Riisager, A. Catalytic performance of zeolite-supported vanadia in the aerobic oxidation of 5-hydroxymethylfurfural to 2,5diformylfuran. ChemCatChem 2013, 5, 284−293. (31) Cui, M.; Huang, R.; Qi, W.; Su, R.; He, Z. Cascade catalysis via dehydration and oxidation: one-pot synthesis of 2,5-diformylfuran from fructose using acid and V2O5/ceramic catalysts. RSC Adv. 2017, 7, 7560−7566. (32) Aellig, C.; Scholz, D.; Conrad, S.; Hermans, I. Intensification of TEMPO-mediated aerobic alcohol oxidations under three-phase flow conditions. Green Chem. 2013, 15, 1975−1980. (33) Miao, C.-X.; He, L.-N.; Wang, J.-Q.; Wang, J.-L. TEMPO and carboxylic acid functionalized imidazolium salts/sodium nitrite: An efficient, reusable, transition metal-free catalytic system for aerobic oxidation of alcohols. Adv. Synth. Catal. 2009, 351, 2209−2216. (34) Karimi, B.; Mirzaei, H. M.; Farhangi, E. Fe3O4@ SiO2-TEMPO as a magnetically recyclable catalyst for highly selective aerobic oxidation of 5-hydroxymethylfurfural into 2,5-diformylfuran under Metal- and halogen-free conditions. ChemCatChem 2014, 6, 758−762. (35) Rapeyko, A.; Arias, K. S.; Climent, M. J.; Corma, A.; Iborra, S. Polymers from biomass: one pot two-step synthesis of furilydenepropanenitrile derivatives with MIL-100(Fe) catalyst. Catal. Sci. Technol. 2017, 7, 3008−3016. (36) Li, J.; Lv, G.; Lu, B.; Wang, Y.; Deng, T.; Hou, X.; Yang, Y. Benzoic acid/TEMPO as a highly efficient metal-free catalyst system for selective oxidation of 5-hydroxymethylfurfural into 2, 5diformylfuran. Energy Technol. 2017, 5, 1429−1434.

(37) Lagerblom, K.; Keskiväli, J.; Parviainen, A.; Mannisto, J.; Repo, T. Selective aerobic oxidation of alcohols with NO3− activated nitroxyl radical/manganese catalyst system. ChemCatChem 2018, 10, 2908−2914. (38) Lagerblom, K.; Lagerspets, E.; Keskiväli, J.; Cook, C.; Ekholm, F.; Parviainen, A.; Repo, T. Practical aerobic oxidation of alcohols: A ligand-enhanced 2,2,6,6-tetramethylpiperidine-1-oxy/manganese nitrate catalyst system. ChemCatChem 2017, 9, 3880−3887. (39) Scepaniak, J. J.; Wright, A. M.; Lewis, R. A.; Wu, G.; Hayton, T. W. Tuning the reactivity of TEMPO by coordination to a lewis acid: Isolation and reactivity of MCl3(η1-TEMPO) (M = Fe, Al). J. Am. Chem. Soc. 2012, 134, 19350−19353. (40) Cardenas, A. J. P.; Culotta, B. J.; Warren, T. H.; Grimme, S.; Stute, A.; Fröhlich, R.; Kehr, G.; Erker, G. Capture of NO by a frustrated Lewis pair: A new type of persistent N-Oxyl radical. Angew. Chem., Int. Ed. 2011, 50, 7567−7571. (41) Sajid, M.; Stute, A.; Cardenas, A. J. P.; Culotta, B. J.; Hepperle, J.A. M.; Warren, T. H.; Schirmer, B.; Grimme, S.; Studer, A.; Daniliuc, C. G.; Fröhlich, R.; Petersen, J. L.; Kehr, G.; Erker, G. N,N-Addition of frustrated Lewis pairs to nitric oxide: An easy entry to a unique family of aminoxyl radicals. J. Am. Chem. Soc. 2012, 134, 10156− 10168. (42) Ma, S.; Liu, J.; Li, S.; Chen, B.; Cheng, J.; Kuang, J.; Liu, Y.; Wan, B.; Wang, Y.; Ye, J.; Yu, Q.; Yuan, W.; Yu, S. Development of a general and practical iron nitrate/TEMPO-catalyzed aerobic oxidation of alcohols to aldehydes/ketones: Catalysis with table salt. Adv. Synth. Catal. 2011, 353, 1005−1017. (43) Gao, B.; Zhang, D.; Li, Y. Catalytic activity and mechanism of Co-catalysts used in combinational catalysts for aerobic oxidation. Eur. J. Inorg. Chem. 2017, 124−132. (44) Zhao, H.; Sun, W.; Miao, C.; Zhao, Q. Aerobic oxidation of secondary alcohols using NHPI and iron salt as catalysts at room temperature. J. Mol. Catal. A: Chem. 2014, 393, 62−67. (45) Zhou, Z.-Z.; Liu, M.; Lv, L.; Li, C.-J. Silver(I)-catalyzed widely applicable aerobic 1,2-diol oxidative cleavage. Angew. Chem., Int. Ed. 2018, 57, 2616−2620.

7060


Metal Nitrate Catalysis for Selective Oxidation of 5

Recommend Documents