Methane Adsorption Capacities of the Lower ... - ACS Publications

Jun 8, 2015 - ABSTRACT: The adsorption capacities of the Lower Silurian Longamxi and Lower Cambrian Niutitang marine shales in the. Yangtze Platform ...
0 downloads 0 Views 3MB Size
Article pubs.acs.org/EF

Methane Adsorption Capacities of the Lower Paleozoic Marine Shales in the Yangtze Platform, South China Yue Wu,*,† Tailiang Fan,† Shu Jiang,‡ Xiaoqun Yang,† Huaiyu Ding,§ Miaomiao Meng,† and Duan Wei† †

School of Energy Resources, China University of Geosciences, Beijing 100083, People’s Republic of China Energy and Geoscience Institute, University of Utah, Salt Lake City, Utah 84108, United States § Liaohe Oilfield Company, PetroChina, Panjin, Liaoning 124010, People’s Republic of China ‡

ABSTRACT: The adsorption capacities of the Lower Silurian Longamxi and Lower Cambrian Niutitang marine shales in the Yangtze Platform in China were investigated through methane adsorption experiments. The correlations between the adsorption capacities and major factors, e.g., total organic carbon (TOC) contents, thermal maturity, mineral composition, moisture content, pressure, and temperature, were discussed. The isosteric adsorption heat was calculated according to the temperature dependency of the methane adsorption isotherms. The results show that, under the temperature of 30 °C and pressure range of 0−12 MPa, the maximum adsorption capacity of the Longmaxi shales ranges between 0.47 and 3.08 m3/ton of rock and that of the Niutitang shales ranges between 1.59 and 7.43 m3/ton of rock. The Langmuir adsorption capacity varies from 0.54 to 3.84 m3/ton of rock for the Longmaxi shales and from 1.98 to 9.73 m3/ton of rock for the Niutitang shales. The TOC content shows a significantly positive correlation with the adsorption capacity, indicating that organic matter is responsible for adsorbing gas in the shales. For these high mature shales, the thermal maturity shows no effect on the adsorption capacity. The clay minerals show little contributions to the adsorption capacity in the shales because of the effect of the water content. For the studied shales, the moisture exhibits no distinct correlation with the adsorption capacity. The influence of the pressure on the adsorption capacity varies from sample to sample, while the temperature shows a generally negative effect on the adsorption capacity. The isosteric heat of adsorption ranges from 8.48 to 27.35 kJ/mol, with an average of 17.59 kJ/mol, indicating a dominant physical adsorption behavior of the methane molecule in the shales.

1. INTRODUCTION It is widely known that natural gas can be stored in shale reservoirs as free gas, adsorbed gas, and dissolved gas.1−6 It was reported that the adsorbed gas can account for 20−85% in total gas amount in some shale gas plays.3 The methane adsorption capacity of shales is a complex function of geochemistry, mineral composition, pore structure, and reservoir conditions.1,2,5−8 Organic matter is generally thought to be the principle contributor to the adsorption capacity of shales.5−9 Type III organic matter has higher gas adsorption capacity than that of type I and type II organic matter because of the higher content of aromatic compounds in type III organic matter.9 As maturity increases, more micropores (diameter, D < 2 nm) may be developed in the organic matter during the process of kerogen conversion and hydrocarbon generation and expulsion. Thus, the overmature and high total organic carbon (TOC) shale samples generally show larger adsorption capacity than the low mature and low TOC samples. Clay minerals with a porous structure also have a strong impact on gas adsorption capacities in shales.5−8 The adsorption capacities of montmorillonite and illite/semectite are obviously higher than that of kaolinite, chlorite, and illite in the dry state.10 However, the adsorption capacities of clay minerals for the methane molecule would be reduced greatly in the presence of moisture. The influences of the water content on the adsorption capacity in shales were investigated by comparing the adsorption capacities between moisture-equilibrated samples and dry samples. A 40% decrease of the adsorption capacity was found in the moistureequilibrated samples.7,8 Reservoir conditions, e.g., temperature © XXXX American Chemical Society

and pressure, have also been recognized as important factors to influence adsorption capacities of shales. The Lower Silurian Longmaxi and Lower Cambrian Niutitang shales with large thickness, high TOC content, and high brittle mineral content are regarded as the most potential shale gas plays in the Yangtze Platform, south China.11−18 An improved understanding of the adsorption characteristics of these two shale intervals is important and meaningful. The aims of this study are to access the adsorption capacities of the Lower Silurian Longmaxi and Lower Cambrian Niutitang shales in the Yangtze Platform and discuss the key factors influencing the adsorption capacities. Here, some representative shale samples in the Longmaxi and Niutitang Formations from wells or outcrops in the Yangtze Platform were collected for this study. Shale properties, e.g., TOC, vitrinite reflectance (Ro), mineral composition, porosity, and methane adsorption capacities, were measured on the basis of a series of experimental procedures.

2. MATERIALS AND METHODS 2.1. Samples. A total of 14 shale samples with different TOC contents and mineral compositions were collected. Specifically, three Longmaxi shale samples coded CUGB1−CUGB3 are from Doucan1 well in Anhui Province in the Lower Yangtze Platform (note that the Longmaxi Formation is called Gaojiabian Formation in the Lower Received: February 5, 2015 Revised: June 3, 2015

A

DOI: 10.1021/acs.energyfuels.5b00286 Energy Fuels XXXX, XXX, XXX−XXX

Article

Energy & Fuels Yangtze Platform); another five Longmaxi shale samples coded CUGB4−CUGB8 are from Xiye1 well in Guizhou Province in the Upper Yangtze Platform; and six Niutitang shale samples coded CUGB9−CUGB14 are from Fenghuang and Yongshun outcrops in Hunan Province in the Upper Yangtze Platform (Figure 1 and Table 1).

R o = 0.3195 + 0.6790R b

2.2.2. X-ray Diffraction (XRD). Bulk mineralogical composition of shales was derived from the XRD patterns. Eight Longmaxi samples (CUGB1−CUGB8) were first ground into powder, and then XRD analysis was performed on the randomly oriented powder through a Rigaku D/max-2600 diffractometer with Cu Kα radiation, automatic divergent and anti-scatter silts, and a secondary graphite monochromator with a scintillation counter. The generator settings were 40 kV and 40 mA. The diffraction data were recorded from 2° to 76° 2θ with a step width of 0.02° and a counting time of 4 s per step. The mineral content was semi-quantitatively determined on the basis of the intensity of specific reflections, the density, and the mass adsorption coefficient (Cu Kα) of the identified mineral phases. 2.2.3. Porosity. The porosity for eight Longmaxi samples (CUGB1−CUGB8) was measured by mercury injection porosimetry. Samples were dried in an oven for 24 h at 50 °C. The measurements were performed using a AutoPore IV 9520 series mercury porosimeter. The mercury pressure was increased continuously from 0.013 to 200 MPa. 2.2.4. Methane Adsorption Experiments. Methane adsorption measurements were performed on shale powders with a high-pressure gas adsorption and desorption instrument of PCT Pro E&E Siverts model. Two sets of methane adsorption experiments were designed for different objectives in this study. The first set is that the methane adsorption experiments were conducted on three dry powered samples (CUGB1−CUGB3) under high pressures of up to 30 MPa and different temperatures of 50 and 70 °C. The second set is that the adsorption experiments were measured on 11 moisture-equilibrated samples (CUGB4−CUGB14) at a consistent temperature of 30 °C and up to a pressure of 12 MPa. Moisture equilibration of samples followed the ASTM procedure (ASTM D1412-04). Ground samples were placed in a sub-atmospheric desiccator over a saturated salt solution of KCl with controlled relative humidity of 80% at 30 °C for more than 72 h. Equilibrium moisture occurs at the point when the sample weight remains constant. Moisture content was measured by oven-drying, weight-loss calculations. In the adsorption experiment, the amount of adsorbed gas is calculated on the basis of the following mass balance:20

Figure 1. Locations of the sampled wells and outcrops in the Yangtze Platform, south China (modified with permission from ref 18): (1) Doucan1 well in Anhui Province, (2) Xiye1 well in Guizhou Province, (3) Fenghuang outcrop in Hunan Province, and (4) Yongshun outcrop in Hunan Province.

Table 1. Provenance of the Studied Shale Samples and Their Lithostratigraphic Origina sample ID

well/outcrop

formation

depth (m)

CUGB1 CUGB2 CUGB3 CUGB4 CUGB5 CUGB6 CUGB7 CUGB8 CUGB9 CUGB10 CUGB11 CUGB12 CUGB13 CUGB14

Doucan1 Doucan1 Doucan1 Xiye1 Xiye1 Xiye1 Xiye1 Xiye1 Fenghuang Fenghuang Fenghuang Yongshun Yongshun Yongshun

LMX LMX LMX LMX LMX LMX LMX LMX NTT NTT NTT NTT NTT NTT

123 105 95 647.6 636.5 627 569.3 566.4 3 56.9 132.1 12 100 106

(1)

madsorbed = mtotal − ρgas Vvoid

(2)

where madsorbed is the adsorbed gas content, mtotal is the total amount of gas introduced into the system, the void volume (Vvoid) is determined by helium expansion at the measured temperature prior to the adsorption measurement, and the gas density (ρgas) in the corresponding pressure and temperature conditions is calculated from the equation of state by Setzman and Wagner.21 The measured results are presented in volume unit normalized to the rock mass (CH4 m3/ton of rock) or the TOC mass (CH4 m3/ton of TOC) under standard temperature (273.15 K) and standard pressure (105 Pa). 2.2.5. Parameterization of Adsorption Data. The measured adsorption data can be parametrized using the Langmuir model, which is commonly applied to describe the relations between the adsorbed gas on a solid surface and measured pressure at a fixed temperature22

a

LMX = Longmaxi Formation, Lower Silurian. NTT = Niutitang Formation, Lower Cambrian. The locations of wells and outcrops are shown in Figure 1. The depth in outcrop is the distance to the ground.

V = VL 2.2. Methods. 2.2.1. TOC and Ro. The TOC contents of 14 samples were measured through a LECO CS230 carbon/sulfur analyzer. Samples were first crushed to powder with a particle less than 100 mesh, and then 1−2 g samples were pyrolyzed up to 540 °C. The thermal maturity of samples was determined on the basis of the reflectance measurements on pyrobitumen particles. The pyrobitumen reflectance (Rb) was measured through a MVP-3 microscope in nonpolarized light at a wavelength of 546 nm in oil immersion. On each sample, 20 measurements were taken whenever possible. Because of the lack of vitrinite in these early Paleozoic marine shales, Ro was calculated from the measured Rb on the basis of the following arithmetic formula:19

P PL + P

or

V = VL

KP 1 + KP

(3)

where V is the volume of adsorbed gas, VL is the Langmuir volume (on the basis of the monolayer adsorption), which is the maximum adsorption capacity of the absorbent, P is the gas pressure, PL is the Langmuir pressure, at which the adsorbed gas content (V) is equal to half of the Langmuir volume (VL), and K is the Langmuir constant, which is the reciprocal of the Langmuir pressure (PL).

3. RESULTS 3.1. Source Rock Characterization. The results of TOC content and thermal maturity (on the basis of calculated Ro) for 14 samples are listed in Table 2. On the basis of the measured B

DOI: 10.1021/acs.energyfuels.5b00286 Energy Fuels XXXX, XXX, XXX−XXX

Article

Energy & Fuels Table 2. Results of TOC, Calculated Ro, Porosity, and XRD Analysis major minerals (wt %)

a

sample ID

TOC (%)

Ro (%)

porosity (%)

quartz

clay

carbonate

CUGB1 CUGB2 CUGB3 CUGB4 CUGB5 CUGB6 CUGB7 CUGB8 CUGB9 CUGB10 CUGB11 CUGB12 CUGB13 CUGB14

3.5 3.17 1.95 6.05 4.08 0.95 0.64 0.52 8.93 2.21 1.68 7.1 2.91 1.45

2.16 1.52 1.43 3.12 3.22 3.23 2.96 2.94 3.32 3.28 3.41 3.47 3.43 3.41

4.19 1.47 1.39 4.40 1.80 0.60 1.20 0.90 NAa NA NA NA NA NA

78.1 53.3 50.2 63.5 45 38.7 33.2 38.9 NA NA NA NA NA NA

17.5 41 46.9 18.8 30.8 32.4 37.4 29.9 NA NA NA NA NA NA

3.8 1.9 1.9 11.8 12.9 17.3 19.2 18.5 NA NA NA NA NA NA

NA = not available.

Table 3. Maxima in the Adsorption Isotherms (30 °C) and Langmuir-Fitting Parameters for Samples of CUGB4−CUGB14a Vmax

VL

sample ID

TOC (%)

moisture (%)

(m3/ton of rock)

(m3/ton of TOC)

Pmax (MPa)

(m3/ton of rock)

(m3/ton of TOC)

PL (MPa)

CUGB4 CUGB5 CUGB6 CUGB7 CUGB8 CUGB9 CUGB10 CUGB11 CUGB12 CUGB13 CUGB14

6.05 4.08 0.95 0.64 0.52 8.93 2.21 1.68 7.1 2.91 1.45

1.18 1.65 1.68 1.66 1.36 1.75 2.14 1.93 1.67 1.98 1.97

3.08 2.45 1.01 0.47 0.5 7.43 2.36 1.67 6.37 2.88 1.59

50.91 60.05 106.32 73.44 96.15 83.20 106.79 99.40 89.72 98.97 109.66

10.86 10.67 10.65 8.67 8.67 11 11.01 11.17 11.63 11.21 11.13

3.84 3.02 1.01 0.54 0.6 9.73 2.93 1.98 8.19 3.61 1.98

63.47 74.02 106.32 84.38 115.38 108.96 132.58 117.86 115.35 124.05 136.55

2.55 2.49 1.27 1.36 2.3 3.23 2.67 2.15 3.02 2.59 2.29

a

Vmax means the maximum adsorption capacity within the measured pressure range, and Pmax is the corresponding pressure. VL is the Langmuir volume, and PL is the Langmuir pressure.

Most of the samples present a low porosity ranging between 1 and 2%. Two organic-rich samples of CUGB1 and CUGB4 exhibit a large porosity of more than 4%. 3.3. Methane Adsorption Isotherms. The experimentally measured and Langmuir-fitting methane adsorption capacities for samples of CUGB4−CUGB14 are presented in Table 3 and Figure 2. Within the measured pressure range, the maximum methane adsorption capacity ranges between 0.47 and 3.08 m3/ ton of rock for the Longmaxi shales and between 1.59 and 7.43 m3/ton of rock for the Niutitang shales. The Langmuir volumes range from 0.54 to 3.84 m3/ton of rock for the Longmaxi shales and from 1.98 to 9.73 m3/ton of rock for the Niutitang shales. The Langmuir pressures are between 1.27 and 2.55 MPa for the Longmaxi shales and between 2.15 and 3.23 MPa for the Niutitang shales. The Niutitang shales show a generally larger Langmuir volume and Langmuir pressure than the Longmaxi shales. A comparison of the adsorption capacity between the Lower Paleozoic shales in the Yangtze Platform in China and some hot shales in North America was made (Table 4). Because the experimental conditions and measurement methods for the adsorption capacities are different for all of those samples, the comparison in this paper is simple and preliminary. In comparison to those gas-producing shales in North America, the Lower Paleozoic marine shales in the Yangtze Platform

values, the TOC content of the Longmaxi shales ranges between 0.52 and 6.05% and that of the Niutitang shales ranges between 1.45 and 8.93%. Most of the samples are organic-rich (TOC > 2%), except for CUGB6, CUGB7, and CUGB8 with TOC contents of lower than 1%. The Niutitang samples generally contain more organic matter than the Longmaxi samples. Both of the Longmaxi shales and Niutitang shales are overmature, with the calculated Ro values higher than 2% on average. Additionally, many previous publications reported a sapropelic (type I) and humic−sapropelic (type II1) kerogen for the Lower Paleozoic marine shales in the Upper Yangtze Platform.23−25 3.2. Mineralogical Composition and Porosity. The XRD and porosity results for eight Longmaxi samples (CUGB1−CUGB8) are listed in Table 2. On the basis of the XRD data, quartz and clays are the major mineralogical composition for the Longmaxi shales and little carbonate is present. The quartz contents of the samples from Doucan1 well are more than 50% on average, and clay mineral contents are more than 40% on average. Both of the quartz and clay mineral contents of the samples from Xiye1 well are above 30% on average. The samples from Xiye1 well contain more carbonate minerals than the samples from Doucan1 well, which may be caused by their different depositional settings. C

DOI: 10.1021/acs.energyfuels.5b00286 Energy Fuels XXXX, XXX, XXX−XXX

Article

Energy & Fuels

America.23 Tan et al. and Wang et al. reported a linear correlation between the adsorption capacity and TOC content in the Lower Paleozoic shales in the Upper Yangtze Platform in China.17,18 The correlations between the TOC contents and adsorption capacities for the studied samples are illustrated in Figure 3. The Langmuir volumes correlate positively with the TOC contents for both the Longmaxi and Niutitang shales, indicating that organic matter made a significant contribution to the adsorption capacity in these samples. Organic matter is usually porous in high-mature shales, with enough surface area onto which natural gas can adsorb.7,8 Organic matter provides most of the porosity in the Longmaxi samples indicated by the linear correlation between the TOC content and porosity (Figure 4A). Intrapores were largely developed within the organic matter revealed by scanning electron microscopy (SEM) (Figure 4B). 4.2. Effect of Thermal Maturity. Thermal maturity has been reported to affect the adsorption capacity because of texture changes in organic matter.5−9 Many micropores are created during thermal decomposition of organic matter, which can enhance the gas adsorption capacity of shales. Ross and Bustin demonstrated that the adsorption capacity increased with thermal maturity in shale samples from the Western Canadian Sedimentary Basin.7,8 Gasparik et al. reported that adsorption capacity of overmature shales was generally higher than that of low mature or immature shales.1,2 Tan et al. found that the Langmuir adsorption capacity generally increased from immature to overmature samples.18 The relationship between the thermal maturity and adsorption capacity for the studied samples is shown in Figure 5. There is no correlation between the TOC-normalized Langmuir volume and thermal maturity. The Niutitang shales with Ro values of 3.2−3.5% show a generally larger adsorption capacity than the Longamxi shales with Ro values of 2.9−3.2%. For these samples within the overmature range, there is limited potential for porous structure creation during the thermal maturation of organic matter. 4.3. Effect of Mineral Composition. In the present study, the correlations between the adsorption capacity and mineral composition were discussed on the Longmaxi samples, and the Niutitang samples may exhibit a similar relationship. The mineral composition of the Longmaxi shales in the Yangtze Platform is dominated by quartz and clay minerals. Quartz may be irrelevant to the adsorption capacity because of its nonadsorptive nature. Clay minerals with high internal surface area and adsorption energy are regarded as a significant factor to affect the adsorption capacity of shales.5−8 The clay mineral

Figure 2. Methane adsorption isotherms measured at 30 °C for samples of CUGB4−CUGB14. Plot A is for the Longmaxi shales, and plot B is for the Niutitang shales. Points are experimentally measured data, and lines are Langmuir-fitting results.

show a larger adsorption capacity, indicating a great shale gas potential.

4. DISCUSSION 4.1. Effect of Organic Matter Abundance. It is widely acknowledged that organic matter plays an important role in the adsorption capacity of shales. The relationship between TOC contents and adsorption capacities in shales has been studied by many scholars.1,2,5−9,26 For example, Ross and Bustin reported that there were positive correlations between the TOC contents and adsorption capacities in shale samples from the Western Canadian Sedimentary Basin.7,8 The adsorption capacities increased linearly with TOC contents in the Devonian shale samples from basins in northeastern

Table 4. Experimental Conditions and Adsorption Capacities for the Compared Shale Samplesa experimental condition

a

sample

temperature (°C)

pressure (MPa)

moisture (%)

adsorption capacity (m3/ton)

Lower Silurian (UYP) Lower Cambrian (UYP) Lower Silurian (UYP) Lower Cambrian (UYP) Lower Silurian (UYP) Lower Cambrian (UYP) D−M (western Canada) Jurassic (western Canada) Lower Cretaceous (western Canada) Barnett (U.S.)

30

0−12

46

0−25

60

0−11

1.18−1.68 1.67−2.14 0.43−0.62 0.58−2.28 0

30

0−6

30 65

0−6 0−25

0.47−3.08 1.59−7.43 1.02−1.45 0.82−4.77 0.94−2.82 1.19−1.46 0.1−1.6 0.1−2.0 0.04−1.89 0.16−3.47

1.6−5.2 0.6−8.5 1.5−11 0

reference this paper Tan et al.18 Wang et al.17 Ross and Bustin8 Chalmers and Bustin6 Gasparik et al.2

UYP = Upper Yangtze Platform. D−M = Devonian−Mississippian. Unit conversion factor: 1 mmol/g = 22.71 m3/ton. D

DOI: 10.1021/acs.energyfuels.5b00286 Energy Fuels XXXX, XXX, XXX−XXX

Article

Energy & Fuels

Figure 4. (A) Linear correlation between the TOC content and porosity in the Longmaxi shales and (B) SEM image showing pores largely developed within the organic matter.

Figure 3. Correlation plots between the Langmuir adsorption capacity and TOC content. Plot A contains all measured samples; plot B is for the Longmaxi shales; and plot C is for the Niutitang shales.

content correlates negatively with the rock-normalized Langmuir volume in this study (Figure 6A), which may be ascribed to the strong effect of the TOC content; e.g., there are substantially low TOC contents in the clay-rich samples. This phenomenon indicates that organic matter has a more significant impact on the adsorption capacity than clay minerals in the studied samples. To more clearly present the contribution of clay minerals to the adsorption capacity, the adsorption data were normalized to the TOC content. The clay mineral content shows a weakly positive correlation with the TOC-normalized Langmuir volume (Figure 6B), indicating that the clay minerals have little impact on the adsorption capacity in the Longmaxi shales. This phenomenon may be caused by the effect of the water content. The surface of clay minerals has a high affinity of water, which would block the access of methane molecules to the adsorption sites. The contribution of clay minerals to the adsorption capacity in shales may be reduced greatly in the presence of water.

Figure 5. Effect of thermal maturity on the adsorption capacity. The adsorption capacity is represented by the TOC-normalized Langmuir volume. The Niutitang shales show a generally larger adsorption capacity than the Longmaxi shales.

4.4. Effect of Moisture Content. The effect of the moisture content on the adsorption capacity was investigated in many shale samples from around the world.1,2,5−8,27,28 For example, the adsorption capacity was negatively correlated with the moisture content in shale samples from the Western Canadian Sedimentary Basin.7,8 The presence of water may swell the clay minerals, block the pore system, and occupy E

DOI: 10.1021/acs.energyfuels.5b00286 Energy Fuels XXXX, XXX, XXX−XXX

Article

Energy & Fuels

Figure 7. Correlation plots between the moisture content and the (A) rock-normalized Langmuir adsorption capacity and (B) TOCnormalized Langmuir adsorption capacity for the Longmaxi shales. No obvious relationship can be observed.

temperatures of 50 and 70 °C and under a wide range of pressures of up to 30 MPa. The experimental results are shown in Table 5 and Figure 8. The effects of the pressure on the adsorption capacity are quite complex. Figure 8A shows that the adsorbed gas content increases consistently with the increase of the pressure. The adsorption isotherms in Figure 2 also show a monotonous increase of the adsorption capacity with a pressure increase, but the pressures applied in those measurements are relatively low (