Subscriber access provided by UNIV OF CALIFORNIA SAN DIEGO LIBRARIES
Feature
Microplastic exposure assessment in aquatic environments: learning from similarities and differences to engineered nanoparticles Thorsten Hüffer, Antonia Praetorius, Stephan Wagner, Frank Von Der Kammer, and Thilo Hofmann Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.6b04054 • Publication Date (Web): 26 Jan 2017 Downloaded from http://pubs.acs.org on January 27, 2017
Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.
Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.
Page 1 of 29
Environmental Science & Technology
1
Microplastic exposure assessment in aquatic environments: learning from
2
similarities and differences to engineered nanoparticles
3 4
Thorsten Hüffer1,§, Antonia Praetorius1,2,§, Stephan Wagner3,§, Frank von der Kammer*1, Thilo
5
Hofmann* 1,2
6 7
1
8
Research Network, Althanstrasse 14, 1090 Vienna, Austria
9
2
University of Vienna, Department of Environmental Geosciences and Environmental Science
University of Vienna, Research Platform Nano-Norms-Nature, Althanstrasse 14, 1090 Vienna,
10
Austria
11
3
12
Permoserstrasse 15, 04318 Leipzig, Germany
13
§
14
manuscript.
Department of Analytical Chemistry, Helmholtz Centre for Environmental Research – UFZ,
Thorsten Hüffer, Antonia Praetorius and Stephan Wagner contributed equally to this
15 16
*Corresponding authors:
17 18
Thilo Hofmann: E-Mail:
[email protected], Phone: 0043 1 4277 53320 and Frank von der Kammer: E-Mail:
[email protected], Phone: 0043 1 4277 53380
19 20
Total word count: 1200 word equivalents + 3766 text = 4966 words
21
1 ACS Paragon Plus Environment
Environmental Science & Technology
22
TOC art
23 24
Synopsis/Abstract
25
Microplastics (MPs) have been identified as contaminants of emerging concern in aquatic environments
26
and research into their behavior and fate has been sharply increasing in recent years. Nevertheless,
27
significant gaps remain in our understanding of several crucial aspects of MP exposure and risk
28
assessment, including the quantification of emissions, dominant fate processes, types of analytical tools
29
required for characterization and monitoring, and adequate laboratory protocols for analysis and hazard
30
testing. This Feature aims at identifying transferrable knowledge and experience from engineered
31
nanoparticle (ENP) exposure assessment. This is achieved by comparing ENP and MPs based on their
32
similarities as particulate contaminants, while critically discussing specific differences. We also highlight
33
the most pressing research priorities to support an efficient development of tools and methods for MPs
34
environmental risk assessment.
35
2 ACS Paragon Plus Environment
Page 2 of 29
Page 3 of 29
Environmental Science & Technology
36
Introduction
37
The field of environmental exposure and risk assessment of emerging contaminants is often dominated
38
by certain “hot topics”,1 for example, pharmaceuticals, nanomaterials, or (most recently) microplastics.
39
The increased interest in a new, “hot” contaminant class is often based on, or justified by, a significant
40
lack of knowledge concerning its behavior in natural environments and/or the toxic potential of the
41
emerging contaminant, together with a need to assess the suitability of existing regulations or develop
42
new ones. Since an emerging contaminant class is rarely entirely novel and unique, but often shares
43
properties with “established” contaminants, a careful assessment of existing knowledge on related
44
substances help us to direct our research efforts and make more efficient use of limited research
45
resources.
46
Plastic in the aquatic environment is an issue of global concern that is particularly evident from the
47
growing amount of plastic litter found in the world's oceans.2,
48
increase in both public and political attention. As a result, the "Leaders' Declaration" from the 2015 G7
49
Summit in Germany acknowledged the global risks posed by marine litter, particularly plastics, to marine
50
and coastal life, to ecosystems, and also potentially to human health.4 Marine littering has been
51
controlled since the 1970s,5 whereas the debate on the occurrence and the consequences of plastic
52
particles with sizes between 1 µm and 5 mm, so-called microplastics (MPs), in the environment has
53
received increased attention only in the recent decade.6-8 MPs are not only a concern for marine
54
environments, but also for freshwater systems as indicated by preliminary reports on a quantitatively
55
similar degree of contamination in both.7, 9, 10
56
Despite the rapidly growing body of published research into the impacts of MPs on various
57
ecosystems,11 our mechanistic understanding of the behavior of MPs in the environment remains
58
limited. To improve our understanding of the occurrence, behavior and transport of MPs in aquatic
3
This concern has led to a marked
3 ACS Paragon Plus Environment
Environmental Science & Technology
59
systems and to ultimately improve our ability to assess the risks they may present a number of open
60
research questions and challenges remain,5, 7, 12, 13 falling predominantly into the domains of:
61
(1) Elucidating formation, sources and emission pathways,
62
(2) Understanding relevant environmental transformation and transport processes,
63
(3) Developing analytical methods for characterization and monitoring,
64
(4) Designing representative laboratory experiments.
65 66
Over the past decade, research on potential environmental implications of engineered nanoparticles
67
(ENPs), generally defined as particles with at least one dimension < 100 nm,14 has been addressing very
68
similar topics and facing related challenges. Given the particulate nature of both ENPs and MPs, this
69
comes as no surprise. Exposure assessment strategies developed for “conventional” contaminants,
70
present as individual substances in the form of dissolved molecules or ions, are often not adequate for
71
particles. Particulate contaminants are present as more or less stable dispersions (multi-phase systems).
72
As a result, their behavior cannot be described by thermodynamics; i.e. the use of equilibrium partition
73
coefficients, such as for example the octanol-water partition coefficient Kow, which play an important
74
role in exposure predictions of “conventional” organic contaminants are not valid for ENPs and MPs.15
75
Their fate needs to be described by kinetic principles of aggregation and transport and can be largely
76
based on theories developed in colloid/particle science. This is equally valid for ENPs and for MPs.
77
Furthermore, their properties cannot be described by their chemical composition alone, but are also
78
dependent on particle size and shape. Additionally, heterogeneities in particle populations, both in
79
terms of the chemical composition of the individual particles and the polydispersity in their size
80
distributions, often increase the level of difficulty in understanding and predicting fate. Particles on the
81
smaller end of the size spectrum are particularly prone to exhibiting specific effects due to their high
4 ACS Paragon Plus Environment
Page 4 of 29
Page 5 of 29
Environmental Science & Technology
82
surface to volume ratios. Even bulk materials consisting mainly of >> 100 nm sized particles, in terms of
83
mass, often contain a significant nano-fraction, in terms of particle number, at the lower end of their
84
size distribution. This unintentional nano-fraction has been discussed several times for ENPs16-18 and the
85
relevance of nano-plastics (i.e. plastic particles < 100 nm) in environmental exposure assessment of MPs
86
has received increasing attention as well, but so far lacking field data.19-22
87
It quickly becomes apparent that parallels can be drawn between these two groups of emerging
88
contaminants. In this Feature we relate current challenges and open questions regarding the fate and
89
exposure assessment of MPs to lessons learned over a decade of studying ENPs in the environment.23-25
90
First, the similarities between ENPs and MPs are used to identify the transferrable knowledge from ENP
91
exposure assessment (Table 1). This is then followed by a critical discussion of differences requiring
92
specific adjustments for MPs. We aim to support a more rapid development of the tools and methods
93
required to advance MP exposure and ultimately risk assessment so that prompt regulatory action can
94
be taken, where necessary.
95
5 ACS Paragon Plus Environment
Environmental Science & Technology
96
Page 6 of 29
Table 1: Overview of ENPs and MP characteristics and identification of transferrable knowledge from ENPs to MP fate and exposure assessment.
ENP characteristics
MP characteristics
Transferrable knowledge from ENPs
Sources and emission pathways • intentional release: agriculture, remediation • unintentional release: surface run-off, WWTPs, direct release (e.g. sunscreen from bathing)
• unintentional release: dominated by secondary MPs (via fragmentation of macroplastic), primary MPs via WWTPs
• particle size < 100 nm 3 • density often > 1 g/cm • fate processes: dissolution, interaction with biofilm/NOM, heteroaggregation, surface transformations
• MPs: particle size 1 µm - 5 mm; nano-plastics: < 100 nm 3 • density typically 0.9-1.1 g/cm • fate processes: fragmentation, interaction with biofilm/NOM, heteroaggregation, surface transformation, additives leaching
• mass flow models for ENPs transferrable for primary MPs (e.g. microbeads from cosmetics). Fragmentation data needed to assess secondary MP emissions
Environmental transformation and transport • kinetic fate descriptors essential • particle characteristics & properties of the surrounding medium affect fate • adaptation of ENP models with MP-specific properties • particle ageing has to be accounted for
Analytical methods for characterization & monitoring strategies • size distribution • particle number concentration • surface area & chemistry (e.g. type of coating)
• size distribution • particle number/mass concentration • types and concentrations of additives
• importance of particle size and number concentration • sample preparation essential for particle analysis & characterization methods
Representative laboratory experiments • particulate nature requires special considerations • stable dispersion due to electrostatic or steric stabilization
• particulate nature requires special considerations • usually low density combined with large particle size
97
6 ACS Paragon Plus Environment
• use of reference materials and elucidation of fate under well-defined & realistic conditions • use of aged particles • importance of particle characterization • strategies for keeping particles in suspension
Page 7 of 29
Environmental Science & Technology
98
Elucidating formation, sources and emission pathways
99
ENPs are typically incorporated in consumer products or industrial applications to fulfill a specific
100
purpose,26,
27
101
nanofertilizers in agriculture,28, 29 and for contaminant remediation purposes.30 In contrast, MPs are only
102
rarely deliberately incorporated into a product to serve a specific function, but generally occur as so-
103
called secondary MPs,24 resulting from the unintentional release and fragmentation of larger pieces of
104
plastics.6 An exception here are primary MPs, which are specifically produced as micro-scale particles
105
and used predominantly in personal care products, e.g. in the form of microbeads in cosmetic peelings.
106
These primary MPs, which make up only about 0.1-3% of the MPs in the natural environment,31 may
107
dominate locally, e.g. in waste water effluents of urban environments,32 but are globally of minor
108
importance. The predominantly unintentional generation of secondary MPs makes it harder to quantify
109
their sources for mass flow models as total production volumes of plastics may be less relevant in this
110
context, compared to break-up/fragmentation/release processes during or after the use stage. For the
111
release quantification of secondary MP two steps are required: i) quantification of mismanaged plastic
112
waste which is released in the aquatic environment,33 and ii) determination of the rates of
113
fragmentation of the released plastic waste in the aquatic environment.
114
The ENPs produced in the largest volumes typically consist of metals or metal oxides.34, 35 Several mass-
115
flow modeling studies provided emission estimates into different environmental compartments during
116
their life-cycle (e.g. air, water, soil) at global and regional scales.34, 36-38 These emission estimates are
117
mainly based on data or estimates of production volumes or market penetration of ENP-containing
118
products and applications, release rates during use and transfer factors between various life-cycle stages
119
(e.g. retention in waste water treatment). In principle, similar mass flow modeling approaches can be
120
applied to MPs, however, different strategies may be needed to elucidate sources and production
121
volumes.
or are intentionally applied to the environment, for example as nanopesticides or
7 ACS Paragon Plus Environment
Environmental Science & Technology
122
Understanding relevant environmental transformation and transport processes
123
Understanding the transport and transformation processes that contaminants undergo in natural
124
environments is essential to assess their fate pathways and predict environmental concentrations.39 For
125
this purpose, laboratory40-43 and mesocosm43, 44 studies as well as environmental fate models45 for ENPs
126
have been developed in recent years, with varying levels of detail, realism and spatial resolution. Many
127
of these approaches could serve as a starting point to study MPs. A river model for ENPs has, for
128
example, already been adapted for modeling the fate of MPs.20 This was possible because the
129
particulate nature of both ENPs and MPs means that the transport processes for both can be in principle
130
described using established concepts from colloid science.15, 20, 46, 47 More specifically, processes affecting
131
the fate of particles in aquatic environments are heteroaggregation with suspended particulate matter
132
(SPM), sedimentation and deposition on surfaces, resuspension, bed load transport, and various
133
transformation and ageing processes (biotic and abiotic) (Figure 1).48, 49 These processes are influenced
134
by the properties of the surrounding aquatic medium (pH, ionic strength, composition, temperature,
135
sunlight, SPM, natural organic matter (NOM) content, flow and turbulence) as well as the particle
136
characteristics (size, shape, density, surface chemistry). 50, 51 The effect of specific differences in MP and
137
ENP properties on their fate need to be accounted for when extrapolating approaches developed for
138
ENP to MPs.
139
Colloidal aggregation and transport processes are strongly influenced by particle sizes and, for the larger
140
colloidal entities, also densities.52 MPs typically fall into size ranges similar to SPM (µm to mm) in
141
contrast to the much smaller ENPs. Most MPs have very low densities close to the density of water (e.g.
142
polyethylene (PE): 0.91-0.95 g/cm3; polypropylene (PP): 0.91-0.92 g/cm3; and polystyrene (PS): 1.01-
143
1.05 g/cm3),5,
144
Ag 10.5 g/cm3, CuO 6.31 g/cm3). The lower densities of MPs combined with their larger sizes compared
145
to ENPs will likely lead to the following differences in aggregation and transport:
53
while ENPs generally have densities greater than 1 g/cm3 (e.g. TiO2 4.26 g/cm3,
8 ACS Paragon Plus Environment
Page 8 of 29
Page 9 of 29
Environmental Science & Technology
146
•
MP-SPM heteroaggregates will be less stable than ENP-SPM heteroaggregates due to the
147
MPs’ larger sizes and heteroaggregates’ porosity.54 Therefore aggregate break-up needs
148
to be accounted for.
149
•
Stronger effect of MP properties on MP-SPM heteroaggregates. Slower sedimentation of
150
MP-SPM heteroaggregates compared to ENP-SPM heteroaggregates or pure SPM, due to
151
lower MP density and higher MP volume fraction in heteroaggregate. Higher potential for
152
MPs to be transported far from their emission source.
153
•
154
SPM acts as a collector for ENPs, whereas MPs could act as collectors of SPM or as substrates for biofilm growth, a scenario that is most unlikely for ENPs.
155
•
ENP movement is dominated by Brownian motion/diffusion due to their small sizes,37
156
whereas MPs experience stronger shear forces during laminar and turbulent flow making
157
them much more susceptible to resuspension from sediments than ENPs.55
158
The heteroaggregation attachment efficiencies (i.e. the probability of heteroaggregate formation upon
159
collision with SPM) of ENPs and MPs will vary according to their different surface characteristics but are
160
expected to follow similar trends, depending on the conditions in the surrounding aquatic medium (e.g.
161
increased heteroaggregation with increasing ionic strength and stabilization in the presence of NOM).20
162
56 57
163
dependent on their composition. Some ENPs undergo fast surface transformation and/or dissolution
164
reactions (e.g. dissolution/sulphidation of silver and copper oxide NPs), 58,59.60,61,62 whereas other remain
165
largely inert (e.g. titanium dioxide and cerium oxide NPs).63 In contrast, MPs made of polymeric material
166
(e.g. PE, PP or PS) are not expected to dissolve in the environment. They can, however, be affected by
167
aging processes, for example when exposed to sunlight. Aging of ENPs results mainly in surface
168
transformations (e.g. oxidation64 or loss of particle coating), whereas aging of MPs typically leads to
169
more brittle particles that could break up into smaller, possibly nanoscale particles (nano-plastics),65
Just like the attachment efficiencies, the transformation behavior of both MPs and ENPs are largely
9 ACS Paragon Plus Environment
Environmental Science & Technology
Page 10 of 29
170
together with the leaching of various additives incorporated during production of the original plastic
171
materials.66
172
Homoaggregation of both ENPs and MPs in aquatic environments is likely to be negligible due to the low
173
particle concentrations expected in surface waters compared to the concentrations of naturally
174
occurring SPM. This can be illustrated by comparing the mean inter-particle distance between MPs and
175
SPM in a typical freshwater body. Assuming a particle number concentration of 316 particles/1000 m³
176
for MP particles with a size of 1 mm (as found in the Danube River by Lechner et al.67), the average
177
distance between MP particles would be 1.8 m. In contrast, the mean distance to SPM, present with a
178
typical mass concentration of 30 mg/L (corresponding to 2.6 × 10particles/1000 m³, assuming a
179
density of 2.0 g/cm³ and a particle size of 0.1 mm) is equal to 2.0 × 10 m, approximately four orders
180
of magnitude less than the mean distance between MP particles.
10 ACS Paragon Plus Environment
Page 11 of 29
Environmental Science & Technology
181 182 183 184
Figure 1: Overview of the most relevant transformation and transport processes affecting ENPs (black circles) and MPs (black
185
Developing analytical methods for characterization and monitoring
186
In case of particulate contaminants such as MPs and ENPs the characterization and quantification in
187
laboratory settings, technical products and natural environments has to go beyond total mass
188
quantification towards a more detailed analysis to reveal information on particle size (distribution),
189
possible coatings, shape and aggregation state.68,
190
improvements in terms of sensitivity and selectivity of microscopic, chromatographic and spectroscopic
191
instruments have led to the identification of promising approaches, which however often require a
pentagons) in aquatic systems. NOM: natural organic matter. The green clouds represent naturally-occurring suspended particulate matter (SPM).
69
For ENPs continuous developments and
11 ACS Paragon Plus Environment
Environmental Science & Technology
Page 12 of 29
192
combination of complementary analytical techniques to elucidate the ENP characteristics (Figure 2).70
193
For example, particle size and particle composition of inorganic ENPs can be determined with a
194
hyphenation of field flow fractionation and element selective detectors such as inductively coupled
195
mass spectrometry (ICP-MS). Further prominent methods to determine ENP size (distribution) include
196
electron microscopy (EM), light scattering and, most recently, single-particle inductively coupled mass
197
spectrometry (sp-ICP-MS) (Figure 2). A particular challenge is associated to the fact that the ENPs of
198
primary concern are those smaller than 10 nm, which are also the most difficult to analyze since most of
199
the analytical methods used are based on the detection of mass.71 The mass scales with the third order
200
to particle size, therefore a 50% reduction in particle size (for spheres) reduces the mass (and hence the
201
signal detected) by 87.5%. The broad size range of MPs ranging over three orders of magnitude or more
202
requires the use of a variety of techniques in order to cover the entire range of sizes (Figure 2). For MPs
203
the development of analytical strategies has so far been focusing on larger size particles (micrometer
204
range and above), where techniques such as sieving, optical microcopy and laser obscuration in
205
combination with Raman or Fourier transformed infrared spectroscopy or thermoanalytical techniques
206
to determine particle composition (polymer type) were applied. Besides particle size and composition,
207
additives in the polymer might be of interest in the discussion of MP analysis. However, analytical
208
methods to analyze polymer additives are not considered in this Feature.
209
The listed techniques which are known from material science are considered as most promising to meet
210
the challenges (particle size and composition i.e. polymer type) for analysis of MPs in the size range >
211
50 µm in aquatic environmental samples.72 For MP size fractions < 50 µm similar challenges (selectivity
212
and sensitivity) as for ENPs arise for the development of analytical methods, where knowledge from
213
ENPs could be integrated (Table 1). The possible existence of nano-plastic particles may lead to a further
214
increase in similarities as encountered for the detection of ENPs above (Figure 2). For particle size
215
determination, field flow fractionation (FFF)73 or liquid chromatography74 techniques might be adapted,
12 ACS Paragon Plus Environment
Page 13 of 29
Environmental Science & Technology
216
but will be challenged by particles > 1 µm. Detection techniques for analysis of organic ENPs
217
(determination of carbon-based ENPs, i.e. C60 fullerenes in environmental samples by atmospheric
218
photoionization with an Orbitrap high resolution MS) are not directly transferable to nano-plastic
219
analysis because of insufficient ionization of the polymer matrix. There is clearly a need to develop and
220
adapt polymer selective detectors (e.g. Raman spectroscopy hyphenated to particle size separation
221
techniques) in order to reveal the existence and fate of nano-sized MPs in environmental matrices.
222
Similar to ENPs, MP characterization in the presence of a particulate matrix (as often encountered in
223
natural systems and biota) requires sample preparation and/or highly specific and sensitive particle
224
analysis. For ENPs determination particle-by-particle analysis using high-resolution and element-specific
225
methods such as electron-microscopy or newly developed spectrometric techniques are under
226
discussion.75 Furthermore, suitable sample preparation strategies are critical to preserve ENP or MP
227
properties, and need to be developed on a case-by-case basis.70 For example, to extract particles from a
228
product or environmental matrix, harsh sample treatment strategies may result in a physical or chemical
229
alteration of particle properties or induce particle aggregation resulting in misleading size
230
measurements.76, 77
231
Although a huge effort is currently being directed to developing appropriate analytical protocols for
232
determining and characterizing levels of MP contamination in aquatic environments, there remain
233
significant discrepancies between different sets of published data due to a lack of standardization (of
234
analytical methods and definitions).78,
235
concentration units in which the occurrence of MPs in aqueous systems is reported. For marine surface
236
samples, these range from mass-based “grams per m3” to number-based “particles per m3” as well as to
237
surface area normalized concentrations “grams per m2” and “particles per m2”.80 The debate on
238
reporting particle number versus mass-based concentrations among the MP research community is
239
reminiscent of similar discussions with respect to ENPs.81 For ENPs, no final agreement on concentration
79
This is particularly evident from the broad variety of
13 ACS Paragon Plus Environment
Environmental Science & Technology
Page 14 of 29
240
metrics has been found, but the discussion has resulted in an increased awareness of the challenges
241
associated with reporting properties of particulate contaminants.
242
243
244 245 246 247 248
Figure 2: Overview of relevant size ranges for ENPs, natural colloids, MPs and nano-plastics and available analytical techniques to characterize particles by size and/or composition. * only in combination with an energy dispersive x-ray detector (EDX) ** no direct measurement, calculated from mass measurements based on information on particle shape stoichiometry *** only in combination with element specific detection e.g. with ICP-MS
249 250
Designing representative laboratory experiments
251
Particulate contaminants require special considerations when it comes to designing adequate laboratory
252
experiments to investigate, for example, their behavior or toxicity. Since particles do not form solutions 14 ACS Paragon Plus Environment
Page 15 of 29
Environmental Science & Technology
253
but more or less stable dispersions, their dispersion stability needs to be controlled in the experimental
254
set-ups. The dispersion stability will depend on both the properties of the particles and of the medium40
255
as well as the particle concentration. At high ionic strength for example, ENPs are prone to aggregation
256
since the dissolved ions in solution effectively screen the repulsive charges on the ENP surfaces and
257
promote aggregation. In systems where their surface charge is important enough to provide
258
electrostatic stabilization against aggregation, the ENPs form stable dispersions, whose movement is
259
dominated by Brownian motion and sedimentation is prevented, even in non-stirred systems (Figure
260
3a). MPs on the other hand, which are often characterized by a lower density and larger sizes, may float
261
in the aquatic media, possibly leading to inhomogeneities in non-stirred systems (Figure 3b). Even in
262
cases where MPs have a density larger than water, stirring would be required to avoid sedimentation
263
due to increased gravitational settling of large and dense particles (Figure 3c).
264
265 266 267 268
Figure 3: Schematic representation of ENPs and MPs in laboratory experiments. The effect of particle size and density is depicted by comparing small particles (nanometer scale) of high density (a), large particles of low density (b) and large particles with high density. Experiments using realistic particle concentrations often fall below analytical detection thresholds (d), while suspensions with concentrations high enough to be detected are prone to fast particle aggregation (e).
269
15 ACS Paragon Plus Environment
Environmental Science & Technology
Page 16 of 29
270
The strong influence that the properties of the surrounding aquatic medium exert on the behavior of
271
particulate contaminants needs to be taken into consideration. Important aspects of ENP fate
272
assessment are i) the use of well-defined aquatic media that are complex enough to be representative
273
of environmental conditions but can be reproduced in standard laboratories,41,
274
knowledge of the ENP characteristics. This will be equally important in similar investigations for MPs. An
275
additional challenge, which may be relevant for both ENPs and MPs is the fact that laboratory
276
experiments typically require the use of particle concentrations that are orders of magnitude greater
277
than those likely to be found in natural environments,12 because the detection limits of currently
278
available analytical methods make it impossible to work at realistic concentrations (Figure 3d).70
279
However, using unrealistically high particle concentrations leads to an exaggerated importance of
280
homoaggregation in laboratory experiments (Figure 3e) relative to realistic scenarios, which needs to be
281
critically accounted for in the experiment interpretation. Techniques used to keep ENPs in a state of
282
dispersion (e.g. sonication, or the addition of NOM or other stabilizers) may be transferrable to MPs.
283
This is expected to be especially relevant for the smaller MPs and nano-plastics that are particularly
284
prone to aggregation, whereas larger particles (> 10 µm) are likely to form looser aggregates which are
285
more affected by shear forces than by surface effects.
286
Another important topic is the effect of particle ageing (i.e. a result of one or more physical or chemical
287
transformations during their life cycle) on ENP behavior.83,
288
synthesized for laboratory experiments, and which have been used in most studies to date, may often
289
not be a good representative of the ENP encountered in real environments. Consequently, including
290
aged ENPs in fate and toxicity testing protocols is being suggested increasingly.85,
291
considerations are highly relevant as well, since the well-defined MP particles typically used in
292
laboratory experiments to date are likely not representative of the MPs found in nature and having
293
undergone various fragmentation and ageing steps.12 Fragmentation is a less relevant process for the
84
82
and ii) a detailed
Pristine ENPs, as can be purchased or
16 ACS Paragon Plus Environment
86
For MPs these
Page 17 of 29
Environmental Science & Technology
294
fate of individual ENPs. However it may play a significant role for the release of ENPs from nano-enabled
295
products and materials. Concepts to quantify release of ENPs due to fragmentation of the product in
296
different life-cycle stages have been addressed in various guidelines.87 These concepts can potentially be
297
adapted for fragmentation of plastic material under environmental conditions.
298
The way forward with MPs
299
Given their particulate nature, which significantly distinguishes both ENPs and MPs from dissolved
300
contaminants and meanwhile represents their strongest commonality, it is clear that knowledge from
301
ENPs fate research can be transferred to MPs based on their similarities (Table 1). The advances made in
302
ENP exposure assessment, both with respect to the tools and methods developed as well as the
303
experience in handling particulate contaminants, can serve as a strong basis for developing exposure
304
assessment approaches for MPs. With this example, the importance of interdisciplinary research teams
305
becomes apparent. By omitting, or not actively seeking, a greater involvement of researchers from other
306
related disciplines such as polymer/material, colloid/nano sciences and hydrology the MP research
307
community would certainly be missing out on a significant contribution that could help to provide
308
improved, faster, and more efficient MP environmental fate, exposure and risk assessment. Most
309
recently, there have been first signs of explicit discussions on how knowledge of ENP research could be
310
integrated into MP ecology24, toxicity23 environmental fate modelling20, and food safety.88 Based on our
311
analysis above, the most pressing research priorities in MPs exposure assessment to be addressed by
312
interdisciplinary approaches can be summarized as:
313
•
Investigation of fragmentation processes of macroplastics and rates of secondary MP
314
formation under various natural conditions are important to account for relevant MP source
315
and emission pathways and asses their environmental fate,
17 ACS Paragon Plus Environment
Environmental Science & Technology
316
•
317 318
Investigation of MP heteroaggregation to obtain MP-specific attachment efficiencies and heteroaggregate break-up rates,
•
319 320
Page 18 of 29
Evaluation of the leaching of additives, and their effects on particle properties and ecosystems,
•
Definition of particle size distribution range(s) and related biological and chemical relevance
321
for the environment would facilitate the development of analytical methods and monitoring
322
strategies,
323
•
Establishment of an analytical framework, which sets analytical techniques for defined
324
particle size fractions and analytical parameters (e.g. the use of FT-infrared microscopy for
325
screening of larger MPs and, if positive, analysis of smaller sizes by Raman microscopy),
326
•
Definition of protocols for stable MP dispersions accounting for the large variety of MP
327
particle properties and sizes is required to design representative and comparable laboratory
328
experiments.
329
MPs and ENPs clearly have strong similarities based on their particulate nature. Many of the strategies
330
developed for ENPs can serve as a solid starting point for addressing research questions related to MP
331
occurrence and fate in the environments, for the design of appropriate laboratory and analytical
332
methods and can help direct research efforts for MP exposure assessment in (aquatic) environments. At
333
the same time several details need to be uncovered specifically for MPs and have been highlighted in
334
the distinct research priorities listed above.
335
18 ACS Paragon Plus Environment
Page 19 of 29
Environmental Science & Technology
336
Author Information
337
Corresponding author:
338
*Email:
[email protected] (T.H.);
[email protected] (F.v.d.K)
339 340
Notes:
341
The authors declare no competing financial interest.
342 343
Acknowledgements
344
We thank Gabriel Sigmund for his helpful comments and discussions.
345
19 ACS Paragon Plus Environment
Environmental Science & Technology
Page 20 of 29
346
Biography
347
Thorsten Hüffer works as a postdoctoral researcher in the Department of Environmental Geosciences at
348
the University of Vienna, focusing on investigations into the phase transfer processes of organic
349
compounds in natural environments and on analytical preconcentration techniques. He is also head of
350
the expert committee on “Plastics in the aquatic environment” within the German Water Chemistry
351
Society.
352
Antonia Praetorius is a postdoctoral researcher in the Department of Environmental Geosciences and
353
the Nano-Norms-Nature Research Platform at the University of Vienna. Her research focuses on
354
assessing and modeling the fate of engineered nanoparticles in natural environments and on
355
interdisciplinary approaches to a sustainable development of nanotechnology.
356
Stephan Wagner is a researcher at the Department of Analytical Chemistry, Helmholtz-Centre for
357
Environmental Research – UFZ, in Leipzig. His research focuses on the development of analytical
358
methods for nanomaterials in consumer products and various environments within the context of risk
359
assessment and the regulatory framework.
360
Frank von der Kammer is currently Vice-Head of the Department for Environmental Geosciences, Senior
361
Scientist and Research Faculty at the University of Vienna. His research interests include environmental
362
colloids, their dynamic behavior and interaction with trace elements, natural nano-scale processes, and
363
nanoparticle characterization in complex samples.
364
Thilo Hofmann is Professor for Environmental Geosciences (Chair) at the University of Vienna. His main
365
research interests are the behavior of organic contaminants in sediments and soils, interactions with
366
nanomaterials, colloid-bound contaminant transport, and the environmental relevance of engineered
367
nanomaterials.
20 ACS Paragon Plus Environment
Page 21 of 29
Environmental Science & Technology
368
References
369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414
1. Wei, T.; Li, M. H.; Wu, C. S.; Yan, X. Y.; Fan, Y.; Di, Z. R.; Wu, J. S., Do scientists trace hot topics? Sci Rep 2013, 3, 5. 2. Galgani, F.; Fleet, D.; Franeker, J. V.; Katsanevakis, S.; Maes, T.; Mouat, J.; Oosterbaan, L.; Poitou, I.; Hanke, G.; Thompson, R.; Amato, E.; Birkun, A.; Janssen, C. Task group 10 report: marine litter; JRC, IFREMER & ICES; 2010. 3. Van Cauwenberghe, L.; Vanreusel, A.; Mees, J.; Janssen, C. R., Microplastic pollution in deep-sea sediments. Environ. Pollut. 2013, 182, 495-499. 4. G7 Presidency 2015 Final Report by the Federal Government on the G7 Presidency 2015. In Press and Information Office of the Federal Government, 11044 Berlin, Germany: 2015. 5. GESAMP Sources, fate and effects of microplastics in the marine environment: a global assessment; 2015. 6. Thompson, R. C.; Olsen, Y.; Mitchell, R. P.; Davis, A.; Rowland, S. J.; John, A. W. G.; McGonigle, D.; Russell, A. E., Lost at Sea: Where Is All the Plastic? Science 2004, 304, (5672), 838. 7. Eerkes-Medrano, D.; Thompson, R. C.; Aldridge, D. C., Microplastics in freshwater systems: A review of the emerging threats, identification of knowledge gaps and prioritisation of research needs. Water Research 2015, 75, 63-82. 8. Cole, M.; Lindeque, P.; Halsband, C.; Galloway, T. S., Microplastics as contaminants in the marine environment: A review. Marine Pollution Bulletin 2011, 62, (12), 2588-2597. 9. Klein, S.; Worch, E.; Knepper, T. P., Occurrence and Spatial Distribution of Microplastics in River Shore Sediments of the Rhine-Main Area in Germany. Environ. Sci. Technol. 2015, 49, (10), 6070-6076. 10. Imhof, H. K.; Ivleva, N. P.; Schmid, J.; Niessner, R.; Laforsch, C., Contamination of beach sediments of a subalpine lake with microplastic particles. Curr. Biol. 2013, 23, (19), R867-R868. 11. Barboza, L. G. A.; Gimenez, B. C. G., Microplastics in the marine environment: Current trends and future perspectives. Marine Pollution Bulletin 2015, 97, (1–2), 5-12. 12. Phuong, N. N.; Zalouk-Vergnoux, A.; Poirier, L.; Kamari, A.; Châtel, A.; Mouneyrac, C.; Lagarde, F., Is there any consistency between the microplastics found in the field and those used in laboratory experiments? Environ. Pollut. 2016, 211, 111-123. 13. Wagner, M.; Scherer, C.; Alvarez-Muñoz, D.; Brennholt, N.; Bourrain, X.; Buchinger, S.; Fries, E.; Grosbois, C.; Klasmeier, J.; Marti, T., Microplastics in freshwater ecosystems: what we know and what we need to know. Environ Sci Eur 2014. 14. EuropeanCommission, Commission Recommendation of 18 October 2011 on the definition of nanomaterial, 2011/696/EU, OJ L 275, 20.10.2011, p. 38–40 In 2011. 15. Praetorius, A.; Tufenkji, N.; Goss, K.-U.; Scheringer, M.; von der Kammer, F.; Elimelech, M., The road to nowhere: equilibrium partition coefficients for nanoparticles. Environ. Sci.: Nano 2014, 1, (4), 317-323. 16. Mitrano, D. M.; Rimmele, E.; Wichser, A.; Erni, R.; Height, M.; Nowack, B., Presence of Nanoparticles in Wash Water from Conventional Silver and Nano-silver Textiles. ACS Nano 2014, 8, (7), 7208-7219. 17. Nowack, B.; Krug, H. F.; Height, M., 120 years of nanosilver history: implications for policy makers. Environ. Sci. Technol. 2011, in press. 18. Weir, A.; Westerhoff, P.; Fabricius, L.; Hristovski, K.; von Goetz, N., Titanium Dioxide Nanoparticles in Food and Personal Care Products. Environ. Sci. Technol. 2012, 46, (4), 2242--2250. 19. Mattsson, K.; Hansson, L. A.; Cedervall, T., Nano-plastics in the aquatic environment. Environmental Science: Processes & Impacts 2015, 17, (10), 1712-1721. 20. Besseling, E.; Quik, J. T. K.; Sun, M.; Koelmans, A. A., Fate of nano- and microplastic in freshwater systems: A modeling study. Environ. Pollut. 2017, 220, (Part A), 540–548. 21 ACS Paragon Plus Environment
Environmental Science & Technology
415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462
Page 22 of 29
21. Gigault, J.; Pedrono, B.; Maxit, B.; Ter Halle, A., Marine plastic litter: the unanalyzed nanofraction. Environ. Sci.: Nano 2016. 22. Koelmans, A. A.; Besseling, E.; Shim, W. J., Nanoplastics in the Aquatic Environment. Critical Review. In Marine Anthropogenic Litter, Bergmann, M.; Gutow, L.; Klages, M., Eds. Springer International Publishing: Cham, 2015; pp 325-340. 23. Bouwmeester, H.; Hollman, P. C. H.; Peters, R. J. B., Potential Health Impact of Environmentally Released Micro- and Nanoplastics in the Human Food Production Chain: Experiences from Nanotoxicology. Environ. Sci. Technol. 2015, 49, (15), 8932-8947. 24. Syberg, K.; Khan, F. R.; Selck, H.; Palmqvist, A.; Banta, G. T.; Daley, J.; Sano, L.; Duhaime, M. B., Microplastics: Addressing Ecological Risk Through Lessons Learned. Environ. Toxicol. Chem. 2015, 34, (5), 945-953. 25. Peijnenburg, W.; Baalousha, M.; Chen, J. W.; Chaudry, Q.; Von der kammer, F.; Kuhlbusch, T. A. J.; Lead, J.; Nickel, C.; Quik, J. T. K.; Renker, M.; Wang, Z.; Koelmans, A. A., A Review of the Properties and Processes Determining the Fate of Engineered Nanomaterials in the Aquatic Environment. Crit. Rev. Environ. Sci. Technol. 2015, 45, (19), 2084-2134. 26. Stark, W. J.; Stoessel, P. R.; Wohlleben, W.; Hafner, A., Industrial applications of nanoparticles. Chemical Society Reviews 2015. 27. Nowack, B.; Boldrin, A.; Caballero, A.; Hansen, S. F.; Gottschalk, F.; Heggelund, L.; Hennig, M.; Mackevica, A.; Maes, H.; Navratilova, J.; Neubauer, N.; Peters, R.; Rose, J.; Schaffer, A.; Scifo, L.; van Leeuwen, S.; von der Kammer, F.; Wohlleben, W.; Wyrwoll, A.; Hristozov, D., Meeting the Needs for Released Nanomaterials Required for Further Testing-The SUN Approach. Environ. Sci. Technol. 2016, 50, (6), 2747-2753. 28. Gogos, A.; Knauer, K.; Bucheli, T. D., Nanomaterials in Plant Protection and Fertilization: Current State, Foreseen Applications, and Research Priorities. J. Agric. Food Chem. 2012, 60, (39), 9781-9792. 29. Kah, M.; Beulke, S.; Tiede, K.; Hofmann, T., Nanopesticides: State of Knowledge, Environmental Fate, and Exposure Modeling. Crit. Rev. Environ. Sci. Technol. 2013, 43, (16), 1823-1867. 30. O'Carroll, D.; Sleep, B.; Krol, M.; Boparai, H.; Kocur, C., Nanoscale zero valent iron and bimetallic particles for contaminated site remediation. Adv. Water Resour. 2013, 51, 104-122. 31. Lassen, C.; Foss Hansen, S.; Magnusson, K.; Norén, F.; Bloch Hartmann, N. I.; Rehne Jensen, P.; Gissel Nielsen, T.; Brinch, A. Microplastics - Occurrence, effects and sources of releases to the environment in Denmark; The Danish Environmental Protection Agency: 2015. 32. Mani, T.; Hauk, A.; Walter, U.; Burkhardt-Holm, P., Microplastics profile along the Rhine River. Sci Rep 2015, 5, 7. 33. Jambeck, J. R.; Geyer, R.; Wilcox, C.; Siegler, T. R.; Perryman, M.; Andrady, A.; Narayan, R.; Law, K. L., Plastic waste inputs from land into the ocean. Science 2015, 347, (6223), 768-771. 34. Keller, A. A.; Lazareva, A., Predicted Releases of Engineered Nanomaterials: From Global to Regional to Local. Environ. Sci. Technol. Lett. 2014, 1, (1), 65-70. 35. Piccinno, F.; Gottschalk, F.; Seeger, S.; Nowack, B., Industrial production quantities and uses of ten engineered nanomaterials in Europe and the world. J. Nanopart. Res. 2012, 14, (9), 1-11. 36. Gottschalk, F.; Sun, T.; Nowack, B., Environmental concentrations of engineered nanomaterials: Review of modeling and analytical studies. Environ. Pollut. 2013, 181, (0), 287-300. 37. Sun, T. Y.; Gottschalk, F.; Hungerbühler, K.; Nowack, B., Comprehensive probabilistic modelling of environmental emissions of engineered nanomaterials. Environ. Pollut. 2014, 185, (0), 69-76. 38. Lazareva, A.; Keller, A. A., Estimating Potential Life Cycle Releases of Engineered Nanomaterials from Wastewater Treatment Plants. ACS Sustainable Chemistry & Engineering 2014, 2, (7), 1656--1665. 39. Lowry, G. V.; Hotze, E. M.; Bernhardt, E. S.; Dionysiou, D. D.; Pedersen, J. A.; Wiesner, M. R.; Xing, B. S., Environmental Occurrences, Behavior, Fate, and Ecological Effects of Nanomaterials: An Introduction to the Special Series. J. Environ. Qual. 2010, 39, (6), 1867-1874. 22 ACS Paragon Plus Environment
Page 23 of 29
463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510
Environmental Science & Technology
40. Baalousha, M., Effect of nanomaterial and media physicochemical properties on nanomaterial aggregation kinetics. NanoImpact 2016, in press. 41. Hammes, J.; Gallego-Urrea, J. A.; Hassellöv, M., Geographically distributed classification of surface water chemical parameters influencing fate and behavior of nanoparticles and colloid facilitated contaminant transport. Water Research 2013, 47, (14), 5350--5361. 42. Kammer, F. v. d.; Ottofuelling, S.; Hofmann, T., Assessment of the physico-chemical behavior of titanium dioxide nanoparticles in aquatic environments using multi-dimensional parameter testing. Environ. Pollut. 2010, 158, (12), 3472-3481. 43. Lowry, G. V.; Espinasse, B. P.; Badireddy, A. R.; Richardson, C. J.; Reinsch, B. C.; Bryant, L. D.; Bone, A. J.; Deonarine, A.; Chae, S.; Therezien, M.; Colman, B. P.; Hsu-Kim, H.; Bernhardt, E. S.; Matson, C. W.; Wiesner, M. R., Long-Term Transformation and Fate of Manufactured Ag Nanoparticles in a Simulated Large Scale Freshwater Emergent Wetland. Environ. Sci. Technol. 2012, 46, (13), 7027--7036. 44. Tella, M.; Auffan, M.; Brousset, L.; Issartel, J.; Kieffer, I.; Pailles, C.; Morel, E.; Santaella, C.; Angeletti, B.; Artells, E.; Rose, J.; Thiéry, A.; Bottero, J.-Y., Transfer, Transformation, and Impacts of Ceria Nanomaterials in Aquatic Mesocosms Simulating a Pond Ecosystem. Environ. Sci. Technol. 2014, 48, (16), 9004-9013. 45. Dale, A. L.; Casman, E. A.; Lowry, G. V.; Lead, J. R.; Viparelli, E.; Baalousha, M., Modeling Nanomaterial Environmental Fate in Aquatic Systems. Environ. Sci. Technol. 2015, 49, (5), 2587-2593. 46. Elimelech, M.; Gregory, J.; Jia, X.; Williams, R. A., Particle Deposition & Aggregation ButterworthHeinemann: Woburn, 1995. 47. Arvidsson, R.; Molander, S.; Sandén, B. A.; Hassellöv, M., Challenges in Exposure Modeling of Nanoparticles in Aquatic Environments. Human and Ecological Risk Assessment: An International Journal 2011, 17, (1), 245--262. 48. Praetorius, A.; Scheringer, M.; Hungerbuhler, K., Development of Environmental Fate Models for Engineered Nanoparticles-A Case Study of TiO2 Nanoparticles in the Rhine River. Environ. Sci. Technol. 2012, 46, (12), 6705-6713. 49. Quik, J. T. K.; de Klein, J. J. M.; Koelmans, A. A., Spatially explicit fate modelling of nanomaterials in natural waters. Water Research 2015, 80, (0), 200-208. 50. Keller, A. A.; Wang, H. T.; Zhou, D. X.; Lenihan, H. S.; Cherr, G.; Cardinale, B. J.; Miller, R.; Ji, Z. X., Stability and Aggregation of Metal Oxide Nanoparticles in Natural Aqueous Matrices. Environ. Sci. Technol. 2010, 44, (6), 1962-1967. 51. von der Kammer, F.; Ottofuelling, S.; Hofmann, T., Assessment of the physico-chemical behavior of titanium dioxide nanoparticles in aquatic environments using multi-dimensional parameter testing. Environ. Pollut. 2010, 158, (12), 3472-3481. 52. Therezien, M.; Thill, A.; Wiesner, M. R., Importance of heterogeneous aggregation for NP fate in natural and engineered systems. Sci. Total Environ. 2014, 485--486, (0), 309--318. 53. PlasticEurope, Plastics – the Facts 2015. 2016. 54. Oles, V., Shear-induced aggregation and breakup of polystyrene latex particles. Journal of Colloid and Interface Science 1992, 154, (2), 351-358. 55. Nizzetto, L.; Bussi, G.; Futter, M. N.; Butterfield, D.; Whitehead, P. G., A theoretical assessment of microplastic transport in river catchments and their retention by soils and river sediments. Environ. Sci.-Process Impacts 2016, 18, (8), 1050-1059. 56. Praetorius, A.; Labille, J.; Scheringer, M.; Thill, A.; Hungerbühler, K.; Bottero, J.-Y., Heteroaggregation of titanium dioxide nanoparticles with model natural colloids under environmentally relevant conditions. Environ. Sci. Technol. 2014, 48, (18), 10690–10698. 57. Smith, B. M.; Pike, D. J.; Kelly, M. O.; Nason, J. A., Quantification of Heteroaggregation between Citrate-Stabilized Gold Nanoparticles and Hematite Colloids. Environ. Sci. Technol. 2015, 49, (21), 1278912797. 23 ACS Paragon Plus Environment
Environmental Science & Technology
511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557
58. Vencalek, B. E.; Laughton, S. N.; Spielman-Sun, E. R.; Rodrigues, S. M.; Unrine, J. M.; Lowry, G. V.; Gregory, K. B., In situ measurement of CuO and Cu(OH)2 nanoparticle dissolution rates in quiescent freshwater mesocosms. Environ. Sci. Technol. Lett. 2016, 3, (10), 375–380. 59. Conway, J. R.; Adeleye, A. S.; Gardea-Torresdey, J.; Keller, A. A., Aggregation, Dissolution, and Transformation of Copper Nanoparticles in Natural Waters. Environ. Sci. Technol. 2015, 49, (5), 27492756. 60. Misra, S. K.; Dybowska, A.; Berhanu, D.; Luoma, S. N.; Valsami-Jones, E., The complexity of nanoparticle dissolution and its importance in nanotoxicological studies. Sci. Total Environ. 2012, 438, 225-232. 61. Unrine, J. M.; Colman, B. P.; Bone, A. J.; Gondikas, A. P.; Matson, C. W., Biotic and Abiotic Interactions in Aquatic Microcosms Determine Fate and Toxicity of Ag Nanoparticles. Part 1. Aggregation and Dissolution. Environ. Sci. Technol. 2012, 46, (13), 6915--6924. 62. Kaegi, R.; Voegelin, A.; Ort, C.; Sinnet, B.; Thalmann, B.; Krismer, J.; Hagendorfer, H.; Elumelu, M.; Mueller, E., Fate and transformation of silver nanoparticles in urban wastewater systems. Nanotechnology for Water and Wastewater Treatment 2013, 47, (12), 3866--3877. 63. OECD Nanomaterials in Waste Streams: Current Knowledge on Risks and Impacts Paris, 2016. 64. Hüffer, T.; Kah, M.; Hofmann, T.; Schmidt, T. C., How Redox Conditions and Irradiation Affect Sorption of PAHs by Dispersed Fullerenes (nC60). Environ. Sci. Technol. 2013, 47, (13), 6935-6942. 65. Lambert, S.; Wagner, M., Characterisation of nanoplastics during the degradation of polystyrene. Chemosphere 2016, 145, 265-268. 66. Andrady, A. L., Microplastics in the marine environment. Mar. Pollut. Bull. 2011, 62, (8), 15961605. 67. Lechner, A.; Keckeis, H.; Lumesberger-Loisl, F.; Zens, B.; Krusch, R.; Tritthart, M.; Glas, M.; Schludermann, E., The Danube so colourful: A potpourri of plastic litter outnumbers fish larvae in Europe's second largest river. Environ. Pollut. 2014, 188, 177-181. 68. Hassellov, M.; Readman, J. W.; Ranville, J. F.; Tiede, K., Nanoparticle analysis and characterization methodologies in environmental risk assessment of engineered nanoparticles. Ecotoxicology 2008, 17, (5), 344-361. 69. Hassellov, M.; Kaegi, R., Analysis and Characterization of Manufactured Nanoparticles in Aquatic Environments. In Environmental and Human Health Impacts of Nanotechnology, Lead, J.; Smith, E., Eds. Wiley-Blackwell: 2009. 70. von der Kammer, F.; Ferguson, P. L.; Holden, P. A.; Masion, A.; Rogers, K. R.; Klaine, S. J.; Koelmans, A. A.; Horne, N.; Unrine, J. M., Analysis of engineered nanomaterials in complex matrices (environment and biota): General considerations and conceptual case studies. Environ. Toxicol. Chem. 2012, 31, (1), 32-49. 71. Babick, F.; Mielke, J.; Wohlleben, W.; Weigel, S.; Hodoroaba, V. D., How reliably can a material be classified as a nanomaterial? Available particle-sizing techniques at work. J. Nanopart. Res. 2016, 18, (6), 40. 72. Ivleva, N. P.; Wiesheu, A. C.; Niessner, R., Microplastic in Aquatic Ecosystems. Angewandte Chemie International Edition 2016, in press. 73. Herrero, P.; Bauerlein, P. S.; Emke, E.; Marce, R. M.; de Voogt, P., Size and concentration determination of (functionalised) fullerenes in surface and sewage water matrices using field flow fractionation coupled to an online accurate mass spectrometer: Method development and validation. Anal. Chim. Acta 2015, 871, 77-84. 74. Kolkman, A.; Emke, E.; Bauerlein, P. S.; Carboni, A.; Tran, D. T.; ter Laak, T. L.; van Wezel, A. P.; de Voogt, P., Analysis of (Functionalized) Fullerenes in Water Samples by Liquid Chromatography Coupled to High-Resolution Mass Spectrometry. Anal. Chem. 2013, 85, (12), 5867-5874.
24 ACS Paragon Plus Environment
Page 24 of 29
Page 25 of 29
558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599
Environmental Science & Technology
75. Borovinskaya, O.; Gschwind, S.; Hattendorf, B.; Tanner, M.; Gunther, D., Simultaneous Mass Quantification of Nanoparticles of Different Composition in a Mixture by Microdroplet GeneratorICPTOFMS. Anal. Chem. 2014, 86, (16), 8142-8148. 76. Wagner, S.; Legros, S.; Loeschner, K.; Liu, J.; Navratilova, J.; Grombe, R.; Linsinger, T. P. J.; Larsen, E. H.; von der Kammer, F.; Hofmann, T., First steps towards a generic sample preparation scheme for inorganic engineered nanoparticles in a complex matrix for detection, characterization, and quantification by asymmetric flow-field flow fractionation coupled to multi-angle light scattering and ICP-MS. J. Anal. At. Spectrom. 2015, 30, (6), 1286-1296. 77. Loeschner, K.; Navratilova, J.; Kobler, C.; Molhave, K.; Wagner, S.; von der Kammer, F.; Larsen, E. H., Detection and characterization of silver nanoparticles in chicken meat by asymmetric flow field flow fractionation with detection by conventional or single particle ICP-MS. Anal. Bioanal. Chem. 2013, 405, (25), 8185-8195. 78. Dehaut, A.; Cassone, A. L.; Frere, L.; Hermabessiere, L.; Himber, C.; Rinnert, E.; Riviere, G.; Lambert, C.; Soudant, P.; Huvet, A.; Duflos, G.; Paul-Pont, I., Microplastics in seafood: Benchmark protocol for their extraction and characterization. Environ. Pollut. 2016, 215, 223-233. 79. OSPAR OSPAR Request on Development of a Common Monitoring Protocol for Plastic Particles in Fish Stomachs and Selected Shellfish on the Basis of Existing Fish Disease Survey.; 2015. 80. Hidalgo-Ruz, V.; Gutow, L.; Thompson, R. C.; Thiel, M., Microplastics in the Marine Environment: A Review of the Methods Used for Identification and Quantification. Environ. Sci. Technol. 2012, 46, (6), 3060-3075. 81. Handy, R. D.; von der Kammer, F.; Lead, J. R.; Hassellov, M.; Owen, R.; Crane, M., The ecotoxicology and chemistry of manufactured nanoparticles. Ecotoxicology 2008, 17, (4), 287-314. 82. Ottofuelling, S.; Von Der Kammer, F.; Hofmann, T., Commercial Titanium Dioxide Nanoparticles in Both Natural and Synthetic Water: Comprehensive Multidimensional Testing and Prediction of Aggregation Behavior. Environ. Sci. Technol. 2011, 45, (23), 10045-10052. 83. Mudunkotuwa, I. A.; Pettibone, J. M.; Grassian, V. H., Environmental Implications of Nanoparticle Aging in the Processing and Fate of Copper-Based Nanomaterials. Environ. Sci. Technol. 2012, 46, (13), 7001--7010. 84. Auffan, M.; Masion, A.; Labille, J.; Diot, M.-A.; Liu, W.; Olivi, L.; Proux, O.; Ziarelli, F.; Chaurand, P.; Geantet, C.; Bottero, J.-Y.; Rose, J., Long-term aging of a CeO2 based nanocomposite used for wood protection. Environ. Pollut. 2014, 188, 1-7. 85. Hendren, C. O.; Lowry, G. V.; Unrine, J. M.; Wiesner, M. R., A functional assay-based strategy for nanomaterial risk forecasting. Sci. Total Environ. 2015, 536, 1029-1037. 86. Al-Abed, S. R.; Virkutyte, J.; Ortenzio, J. N. R.; McCarrick, R. M.; Degn, L. L.; Zucker, R.; Coates, N. H.; Childs, K.; Ma, H.; Diamond, S.; Dreher, K.; Boyes, W. K., Environmental aging alters Al(OH)3 coating of TiO2 nanoparticles enhancing their photocatalytic and phototoxic activities. Environ. Sci.: Nano 2016. 87. Wohlleben, W.; Meyer, J.; Muller, J.; Muller, P.; Vilsmeier, K.; Stahlmecke, B.; Kuhlbusch, T. A. J., Release from nanomaterials during their use phase: combined mechanical and chemical stresses applied to simple and multi-filler nanocomposites mimicking wear of nano-reinforced tires. Environ.-Sci. Nano 2016, 3, (5), 1036-1051. 88. Statement on the presence of microplastics and nanoplastics in food, with particular focus on seafood; EFSA CONTAM Panel (EFSA Panel on Contaminants in the Food Chain): 2016; p 30.
600
25 ACS Paragon Plus Environment
Environmental Science & Technology
ACS Paragon Plus Environment
Page 26 of 29
Page 27 of 29
Environmental Science & Technology
Figure 1: Overview of the most relevant transformation and transport processes affecting ENPs (black circles) and MPs (black pentagons) in aquatic systems. NOM: natural organic matter. The green clouds represent naturally-occurring suspended particulate matter (SPM). 157x142mm (300 x 300 DPI)
ACS Paragon Plus Environment
Environmental Science & Technology
ACS Paragon Plus Environment
Page 28 of 29
Page 29 of 29
Environmental Science & Technology
Figure 3: Schematic representation of ENPs and MPs in laboratory experiments. The effect of particle size and density is depicted by comparing small particles (nanometer scale) of high density (a), large particles of low density (b) and large particles with high density. Experiments using realistic particle concentrations often fall below analytical detection thresholds (d), while suspensions with concentrations high enough to be detected are prone to fast particle aggregation (e). 80x30mm (300 x 300 DPI)
ACS Paragon Plus Environment