Subscriber access provided by Nottingham Trent University
Environmental and Carbon Dioxide Issues
Mineral carbonation for carbon utilization in microalgae culture Zi Ye, Juliana Abraham, Christos Christodoulatos, and Valentina Prigiobbe Energy Fuels, Just Accepted Manuscript • DOI: 10.1021/acs.energyfuels.9b01232 • Publication Date (Web): 21 Aug 2019 Downloaded from pubs.acs.org on August 29, 2019
Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.
is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.
Page 1 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Energy & Fuels
Mineral carbonation for carbon utilization in microalgae culture Zi Ye,†,‡ Juliana Abraham,†,‡ Christos Christodoulatos,† and 1
Valentina Prigiobbe∗,† †Department of Civil, Environmental, and Ocean Engineering, Stevens Institute of Technology, Hoboken (NJ) U.S.A.. ‡Contributed equally to this work E-mail:
[email protected] 2
Abstract
3
This paper presents a study on the combination of mineral carbonation with biomass
4
production. Laboratory experiments were performed to investigate the growth of fresh-
5
water green microalgae Scenedesmus obliquus in the presence of dissolving mineral
6
carbonates, such as nahcolite (NaHCO3 ) and nesquehonite (MgCO3 -3H2 O) at atmo-
7
spheric conditions and 25 ◦ C. The cell density of the algae biomass was determined
8
using fluorescence measurements. A bio-chemical model was implemented to describe
9
the evolution of the biomass and the consumption of carbon substrate. The parameter
10
estimates show that the algae growth kinetics in the presence of either NaHCO3 or
11
MgCO3 -3H2 O is similar and is comparable to the literature. Moreover, when MgCO3 -
12
3H2 O is supplied the algae appear to form clusters, which favor their separation from
13
the solution. Overall, this work analyzes the potential to combine two carbon dioxide
14
(CO2 ) utilization options, i.e., mineral carbonation and microalgae cultivation, and it
15
demonstrates the feasibility of the process. However, control of the pH and the carbon
16
dosage is required to attain optimal biomass productivity.
1
ACS Paragon Plus Environment
Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
17
Introduction
18
Carbon dioxide (CO2 ) concentration in the atmosphere has increased from approximately
19
277 ppm at the beginning of the industrial era to 407.80 ppm in 2018 1 . The major contri-
20
bution to such an increase is fossil-fuel combustion and industry 2 . Recent work by Le Qu´er´e
21
et al. 2 reports that the total global carbon emission from these anthropogenic activities has
22
reached 9.4 ± 0.5 Gt per year. Consequences of carbon accumulation in the atmosphere are
23
temperature increase and climate change 3,4 . The Paris Agreement 5 fixes the limit of CO2
24
concentration in the atmosphere to keep the global temperature rise within this century well
25
below 2 ◦ C above pre-industrial levels. To reach this goal, significant changes in the energy
26
production and CO2 management need to be implemented 6 . Carbon Capture Utilization and
27
Storage (CCUS) techniques aim at mitigating CO2 emissions towards the atmosphere and
28
include: geological storage, ocean storage, and carbon mineralization 6,7 . Among the most
29
promising options, there are geological storage, e.g., in deep saline aquifers, and CO2 utiliza-
30
tion in enhanced oil recovery (EOR) with assumed long-term storage. However, the relatively
31
high cost of the conventional CCUS systems remains a major barrier to their widespread
32
deployment at power plants and other industries. 8,9 Recently, the beneficial reuse or conver-
33
sion of CO2 into various products, such as, e.g., chemicals, fuels, and construction materials,
34
has been considered 10–15 Among the different options, microalgae cultivation and mineral
35
carbonation are able to capture CO2 and convert it into valuable products 16 .
36
Microalgae cultivation has the potential to become a major global renewable fuel source,
37
utilizing sunlight, CO2 , and nutrients to rapidly produce long chain oils 17–20 . Commer-
38
cial scale algal growth reactors, either open-pond systems or enclosed photo-bioreactors,
39
require supplemental inorganic carbon sources. Traditionally, this is achieved by supplying
40
high-purity gaseous CO2 21 . However, the use of pure gas may have significant impact on
41
the overall economics of the process as may require closed reactors and a controlled atmo-
42
sphere 22,23 . One of the major barriers to large-scale commercial deployment is indeed the
43
need for high-purity CO2 for the otherwise significant potential of algal biofuels 24 . Pure 2
ACS Paragon Plus Environment
Page 2 of 31
Page 3 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Energy & Fuels
44
CO2 sources are rare, and even dilute sources may not be available or not located nearby
45
algae production plants 25,26 . To overcome this issue, recent studies have investigated the
46
possibility to use directly industrial flue-gases 27,28 . However, raw flue-gases usually con-
47
tain other gaseous components such as NOx and SOx that have a negative effect on algae
48
growth 29 . Other studies show that inorganic carbon, in the form of bicarbonate ions (HCO− 3)
49
can be a good alternative source of carbon 29–32 . Photosynthetic microorganisms can uptake
50
inorganic carbon only as CO2 gas since the enzyme responsible for the assimilation of the
51
carbon (i.e., Ribulose-1,5-bisphosphate carboxylase/oxygenase also commonly known as RU-
52
BISCO) can only fix CO2 in gaseous form. However, bicarbonates constitute another form
53
of inorganic carbon that these microorganisms can store depending upon the species and
54
the conditions of the environment. Bicarbonate ions can accumulate near the RUBISCO
55
limiting CO2 diffusion through the cell. Then, another enzyme called carbonic anhydrase
56
(CA) converts bicarbonate to CO2 before fixation takes place. Specifically the freshwater
57
strain used in the current study, Scenedesmus obliquus, can transform bicarbonates into
58
CO2 and, therefore, use both inorganic carbon forms to grow 33 . Moreover, bicarbonate ions
59
are an effective lipid accumulation trigger for a variety of algae, potentially improving the
60
commercial use of algae as a biofuel resource 34–36 . Therefore, the dissolution of carbonate
61
minerals could be a good alternative option of carbon supply to microalgae, overcoming the
62
major impediment towards achieving an economically attractive biomass productivity. Here,
63
we propose a process which combines microalgae cultivation with mineral carbonation. CO2
64
is dissolved into alkaline wastewater or brine to precipitate carbonates, which are then dis-
65
solved for microalgae growth. Conventional mineral carbonation aims at permanently fixing
66
CO2 into stable carbonates, such as, e.g., magnesite and calcite, that can be disposed of
67
or reused 7,37 . During the precipitation of the carbonates, hydrated phases may form which
68
eventually transform into stable solid phases 38–41 . Mineral carbonation process has been used
69
to produce a large variety of carbonate minerals such as, e.g., calcite (CaCO3 ) 42,43 , nesque-
70
honite (MgCO3 -3H2 O) 44–46 , hydromagnesite Mg5 (CO3 )4 (OH)2 -4H2 O) 47 , magnesite 39,41 , and
3
ACS Paragon Plus Environment
Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
71
sodium bicarbonate (or nahcolite, NaHCO3 ) 48,49 . If carbonates are designed to be reused,
72
e.g., to supply carbon to microalgae, the formation of metastable phases is preferred as they
73
can precipitate quickly and dissolve promptly.
74
This paper presents experimental and modeling efforts to determine the kinetics of mi-
75
croalgae growth in the presence of dissolving carbonate minerals such as, e.g., sodium and
76
magnesium carbonates, and select the best operating conditions to achieve optimal algae
77
growth. Experiments were performed using S. obliquus, NaHCO3 , and MgCO3 -3H2 O to
78
obtain measurements for the development of a bio-chemical model of the process.
79
Material and methods
80
Precipitation and characterization of carbonate minerals
81
Sodium bicarbonate was purchased from Fisher Scientific (U.S.A.) and characterized in our
82
laboratory. Nesquehonite was produced following H¨anchen et al. 39 . A volume of 400 mL of
83
sodium hydroxide (NaOH, 98.9% purity, Sigma-Aldrich, U.S.A.) solution was prepared using
84
ultra-purified water (Milli-Q, U.S.A.). The final concentration was equal to 1.25 mol/kg. The
85
solution was purged with pure CO2 for 24 hours in a continuously-stirred batch reactor (Series
86
5100 Glass Reactors, Parr Instrument Company, U.S.A). Then, the system was stabilized
87
at a temperature of 25 ◦ C and total pressure of 1 bar of pure CO2 . Once equilibrium was
88
reached, a volume of 30 mL of magnesium chloride (MgCl2 -6H2 O, Sigma-Aldrich, U.S.A.)
89
solution was injected into the reactor at the rate of 10 mL/min using a piston pump (Cole-
90
Parmer, U.S.A.). The initial concentrations of sodium (Na+ ) and magnesium (Mg2+ ) ions
91
were 1.1 and 0.19 mol/kg, respectively, corresponding to an initial supersaturation with
92
respect to MgCO3 -3H2 O as large as 1.69 calculated using the open-source geochemical code
93
PHREEQC 50 . The suspension was mixed for 24 hours, then the solids were collected and
94
washed with ultra-purified water and, finally, dried at room temperature.
95
The solids, namely, the commercial NaHCO3 and the produced MgCO3 -3H2 O, were char4
ACS Paragon Plus Environment
Page 4 of 31
Page 5 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Energy & Fuels
96
acterized with a Scanning Electron Microscope (SEM, Auriga 40, Zeiss, U.S.A) and X-ray
97
diffraction analysis (XRD, Ultima IV, Rigaku, U.S.A.). The results of these characteriza-
98
tions are shown in Figure 1. As illustrated in the figure, both measured spectra compare
99
very well with the reference 51 and the SEM image in part b of the figure shows the typical
100
needle-like shape of MgCO3 -3H2 O.
Figure 1: Characterization results of the solids used for algae growth. X-ray diffraction analysis of the solid products and SEM images in the insets for: (a) commercial NaHCO3 and (b) produced MgCO3 -3H2 O. The reference for the XRD spectra is the Jade database 51 .
101
Microalgae growth medium
102
The growth medium selected to provide nutrients to microalgae was prepared following the
103
recipe of commercial BG-11 (BG-11 Freshwater Solution, Sigma-Aldrich, U.S.A.). Within
104
this medium, the sources of carbon, magnesium, and nitrogen were modified on the basis of
105
the type of experiment. Table 1 specifies these sources. Media BG-111 and BG-112 were used
5
ACS Paragon Plus Environment
Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 6 of 31
106
in the microcosm tests, as described in section Microcosm bottles, below. Whereas, media
107
BG-111 through BG-114 were employed in batch tests, as described in section Continuously-
108
stirred batch reactor, below. In particular, in media BG-113 and BG-114 the source of
109
+ nitrogen was changed from NO− 3 to NH4 to better control the pH during the experiments.
110
Oxidized nitrogen sources like nitrate must be reduced before algae uptake generating alka-
111
linity, whereas the nitrogen consumed as ammonium produces acidity 52 . Table 1: Sources of carbon, magnesium, and nitrogen used to modify the original BG-11 medium
BG-111 . BG-112 BG-113 BG-114
Carbon
Magnesium
Nitrogen
NaHCO3
MgSO4 -7H2 O
NaNO3
MgCO3 -3H2 O MgCO3 -3H2 O
NaNO3
NaHCO3
MgSO4 -7H2 O
NH4 Cl
MgCO3 -3H2 O MgCO3 -3H2 O
NH4 Cl
112
Toxicity assessment
113
R Toxicity assessments of the freshwater microalgae S. obliquus (ATCC 11477TM ) to Mg2+
114
were performed. Different concentrations of the cation were used to identify the maximum
115
concentration of MgCO3 -3H2 O that could be used in the algae cultures without any toxicity
116
effect on S. obliquus. Therefore, different concentrations of Mg2+ as MgCO3 -3H2 O were
117
tested in a simple and cost-effective 24-well microplate test, following the protocol described
118
by Abraham et al. 53 . The objective of this assessment was to evaluate the toxicity, if any,
119
of the high concentrations of Mg2+ in solution. Therefore, the rest of the nutrients were
120
provided in excess, including C, to avoid inhibition of growth due to lack of nutrients. The
121
pH of the prepared solutions was adjusted by adding sulfuric acid (H2 SO4 , 98 % purity,
122
Sigma-Aldrich, U.S.A.) up to complete dissolution of the solids.
6
ACS Paragon Plus Environment
Page 7 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Energy & Fuels
123
Growth of microalgae
124
Experiments of microalgae growth were carried out in closed systems using microcosm air-
125
tight bottles and a continuously-stirred batch reactor. Details of the set-ups are provided,
126
herein.
127
Microcosm bottles
128
Closed systems used to grow microalgae consisted of microcosm airtight 250 mL bottles with
129
200 mL working volume. Experimental conditions were selected to test a wide range of carbon
130
concentrations. Preliminary tests to identify the optimal concentration of carbon provided
131
as HCO− 3 were also carried out. Here, NaHCO3 was used and the total carbon concentration
132
was varied from 0 and 1,000 mg/L (Results not shown). Based on the outcomes of these
133
preliminary tests, a narrower range was chosen, namely 12-400 mg/L, for further tests where
134
carbon was supplied as either NaHCO3 or MgCO3 -3H2 O.
135
In all experiments, S. obliquus was initially grown in sterile medium BG-111 or BG-113
136
and used as . The pH of the media prior to inoculation was adjusted between 7 and 8 by
137
adding H2 SO4 . All tests were performed at least in duplicate and were incubated for 7 days
138
at 25 ◦ C in a growth chamber (Caron, U.S.A.), under continuous shaking at 120 rpm using
139
a 14:10 hours light:dark photoperiod and 68 µmol m−2 s−1 of light intensity. Samples were
140
taken at the beginning and at the end of each test and analyzed.
141
Continuously-stirred batch reactor
142
Open systems used to grow microalgae comprised a continuously-stirred batch reactor equipped
143
with temperature and pressure sensors. A solution of 520 mL containing the medium (i.e.,
144
BG-111 through BG-114 depending on the experiment performed) was prepared and placed
145
into the 600 mL double-jacked glass vessel at atmospheric conditions of CO2 and 25 ± 2 ◦ C.
146
In the experiments, where MgCO3 -3H2 O was used, the solids were completely dissolved and
147
the pH was adjusted between 7 and 8. Then, the solution was inoculated with an initial 7
ACS Paragon Plus Environment
Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
148
cell density of ∼ 2.5·105 cells/mL of S. obliquus. During the experiment, the suspension was
149
stirred at 120 rpm, illuminated with 14:10 hours light:dark photoperiod at 98 µmol/(m2 s)
150
of LED light intensity, achieved by 4 LED lights (40 W, 36 LED, 10 inches in length and
151
0.75 inches wide each) equally distributed around the reactor. The pH was adjusted with
152
hydrochloric acid (HCl, Fisher Scientific, U.S.A.). Samples were taken twice a day and
153
characterized offline.
154
Characterization of the solution
155
Samples, collected during the tests, were analyzed for pH using a digital sensor (Oakton PC
156
700 pH meter, U.S.A.) with measurement error of ± 0.01. Upon filtration using a 0.45 µm
157
pore size filter, the total carbon (TC) was determined by means of a UV-Persulfate TOC
158
Analyzer (Phoenix 8000 instrument, Teledyne Tekmar, U.S.A.) and Mg2+ concentration
159
was determined using inductively coupled plasma-optical emission spectrometry (ICP-OES,
160
Model 5100, Agilent Technologies, U.S.A).
161
Characterization of the microalgae suspension
162
Microalgal density was determined periodically on unfiltered samples by measuring their
163
R fluorescence on a microplate reader (Cytation 3, Biotek ) utilizing 445/685 nm excita-
164
tion/emission filters and the results were expressed as a mean of cell density (CD, cells/mL).
165
Moreover, a standard curve to obtain a relationship between cell density and dry weight
166
(DW, g/L) was generated. Glass microfiber filters (GE Bio-Sciences, part no. 1821-055)
167
were initially dried in an oven at 105 ◦ C for two hours. Separately, microalgae suspensions
168
were filtered and dried at the same temperature for two hours, as well. The dried filters
169
were weighted at room temperature before and after filtering. Microalgae cells were counted
170
using the hemocytometer protocol 54 . The relationship between fluorescence measurements-
171
cell counting and dry weight were found to be: DW = CD/(4·107 ) with R2 = 0.996 and
172
DW = CD/(3·107 ) with R2 = 0.996 for NaHCO3 and MgCO3 -3H2 O, respectively. Images of 8
ACS Paragon Plus Environment
Page 8 of 31
Page 9 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Energy & Fuels
173
the green color developed due to the microalgae growth were recorded and microscopy cell
174
R analysis was performed using an image reader (Cytation 3, Biotek ).
175
Modeling
176
Geochemical model
177
A geochemical model was developed to describe the chemical composition of the investigated
178
system and implemented in the open-source software PHREEQC 50 . The dominant chemical
179
reactions for the dissolution/precipitation of the carbonate minerals,
180
NaHCO3 + H+ ←→ Na+ + HCO− 3,
(1)
MgCO3 · 3H2 O + H+ ←→ Mg2+ + HCO− 3 + 3H2 O,
(2)
Mg2 (CO3 )(H2 O) − 3H2 O + H+ ←→ 2Mg2+ + HCO− 3 + 5H2 O,
(3)
and the aqueous speciation,
CO2,gas ←→ CO2,sol ,
(4)
CO2,sol + H2 O ←→ H2 CO3 ,
(5)
+ H2 CO3 ←→ HCO− 3 +H ,
(6)
+ 2− HCO− 3 ←→ CO3 + H .
(7)
181
reactions 1 through 7 were assumed at local equilibrium during the growth of the microalgae.
182
To design the experiments, the chemical composition of the liquid phase at the oper-
183
ating conditions for microalgae growth, i.e., atmospheric pressure of CO2 and 25 ◦ C, were
184
determined. To this aim, the supersaturation ratios with respect to NaHCO3 (Snah ), MgCO3 -
185
3H2 O (Snes ), and artinite (Mg2 (CO3 )(H2 O)-3H2 O, Sart ) were calculated as a function of ion
9
ACS Paragon Plus Environment
Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
186
Page 10 of 31
concentration. Namely, Snah , Sart and Snes , are expressed by 55 : Snah = Sart =
Snes =
aN a+ aHCO3−
1/2
Ksp,nah
,
a2M g2+ aHCO3− a5H2 O
(8)
!1/8
a3H + Ksp,art aM g2+ aHCO3− a3H2 O
,
(9)
,
(10)
!1/5
aH + Ksp,nes
187
where a and Ksp are the activity and the solubility product of the subscript species and solid
188
phase, respectively. At 25 ◦ C, log10 Ksp,nah , log10 Ksp,art , and log10 Ksp,nes are, correspondingly,
189
-0.11, 19.66, and 4.99.
190
Figure 2 reports the composition diagrams with the supersaturation ratio as contours
191
and on the axes either Na+ (parts a and b) or Mg2+ (parts c and d) concentrations and
192
pH. The corresponding total carbon concentration is also provided as a reference. The gray
193
shaded area indicates the region, where microalgae growth is feasible (i.e., within pH 6 and
194
9), and the system is undersaturated with respect to any solid phase (nahcolite, artinite,
195
and nesquehonite). Namely, in the case of the system where nesquehonite was added as a
196
carbon source the maximum allowable pH was set equal to 8.5 (parts c and d of Figure 2).
197
The initial conditions in each test were selected within this area, i.e., the pH was initially
198
always adjusted to 7 and the concentration of carbon lower than 400 mg/L.
10
ACS Paragon Plus Environment
Page 11 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Energy & Fuels
Figure 2: Contours of Snah (solid blue), Sart (dashed gray) and Snes (solid black), calculated as in eqs. 8, 9, and 10, respectively. Parts (a) and (b) were calculated considering media BG-111 and BG-113 . Parts (c) and (d) were calculated considering media BG-112 and BG114 .
11
ACS Paragon Plus Environment
Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 12 of 31
199
Algae growth model
200
To describe the evolution of the algal growth in the batch reactor system, the Monod kinetics
201
model was implemented, XS dX = µmax − Kd X, dt Ks + X dS XS = −µmax , dt Y (Ks + X)
(11) (12)
202
where t is time (d), X is the concentration of microalgae (mg/L), S is the concentration of
203
substrate (i.e., carbon) (mg/L), and Ks , Kd , µmax , and Y are model parameters, namely,
204
Monod half-saturation constant (mg/L), endogenous decay coefficient (1/d), maximum spe-
205
cific growth rate of microalgae (1/d), and yield (-), respectively. The Monod model assumes
206
that the only limiting growth factor is the availability of carbon and that the macro- and
207
micro-nutrients are present in excess. Eqs. 11 and 12 were solved in MATLAB 56 and used
208
to fit the experimental data. The value of Kd was considered negligible since during the
209
experimental time period of 7 days no cell decay was observed.
210
For the tests carried out in the microcosm bottles, the growth rate was calculated us-
211
ing the initial and the final algae concentrations, i.e., X0 and Xf , respectively, assuming
212
exponential growth and using the following equation 57 ,
µ=
lnXf −lnX0 , tf −t0
(13)
213
where t0 and tf refer to the initial and final time (d). The carbon utilization efficiency (Ec ,
214
%) was also determined as Ec =
Ng C a , S0
(14)
215
where S0 is the initial concentration of the substrate, Ca is the carbon content within the
216
microalgal cell, determined using a CHNS elemental analyzer, and was found to be equal to
217
43.39 and 46.89 % of dry weight for NaHCO3 and MgCO3 -3H2 O, respectively,. Finally Ng 12
ACS Paragon Plus Environment
Page 13 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
218
Energy & Fuels
(cell/mL or mg/L) is the net algal growth,
Ng = X f − X 0 .
(15)
219
Results
220
Microalgal toxicity assessment
221
Magnesium is an essential nutrient for microalgal development since it is part of the chloro-
222
phyll structure, the main molecule responsible for photosynthesis in green microalgae and
223
plants. Earlier work conducted by 58 shows that the biomass and the lipid content of S.
224
obliquus increases with magnesium concentration up to 150 mg/L. However, alkaline-earth
225
elements could be toxic above certain concentrations.
Figure 3: Results of the toxicity assessment given as cell density (CD) of S. obliquus vs. time measured for different concentrations of Mg2+ supplied as MgCO3 -3H2 O. The control test was run using Mg2+ concentration present in the regular BG-11 medium, i.e., 7.5 mg/L.
13
ACS Paragon Plus Environment
Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
226
Therefore, toxicity assessment of magnesium was carried out changing its concentration
227
from 7.5 (control) to 800 mg/L provided as MgCO3 -3H2 O. The mineral carbonate was com-
228
pletely dissolved prior to toxicity assessment. The results are shown in Figure 3 as algae
229
cell density over time. Here, it is possible to see that the algae growth in the presence of
230
MgCO3 -3H2 O is initially slower than that of the control system. To gain an insight into this
231
behaviour, speciation diagrams were calculated at the conditions applied in these tests. The
232
graphs are reported in Figure 2 of the supporting information (SI) document. Here, we can
233
see that, in the range of 6–9 of the operating pH, the carbon in solution partitions within
234
various aqueous complexes, which may reduce the bio-availability of the carbon to the algae
235
for growth. However, after the third day, the growth profile is similar in all tested cases and,
236
2 eventually, the concentration is the same within the uncertainty of the measurements (σm,800
237
2 2 2 2 2 = 5.74·105 , σm,ctrl = 3.22·105 , σm,100 = 3.92·105 , σm,200 = 3.64·105 , σm,400 = 1.70·105 , σm,600
238
2 = 3.14·105 and σd2 = 2.13·106 , where σm and σd2 are the uncertainty of the measurements at
239
given Mg2+ concentrations and the variability of the data). This suggests that magnesium
240
is not toxic to S. obliquus within the investigated concentration range.
241
Growth of microalgae in microcosm bottles
242
Experiments in a closed system using microcosm bottles were performed to study the feasi-
243
bility of microalgae growth under controlled carbon sources, namely, NaHCO3 , and MgCO3 -
244
3H2 O. The conditions applied are listed in Table 2 together with the results, which are also
245
shown in Figure 4. In these tests, the concentration of carbon was varied between 0 and
246
400 mg/L. In the table, the symbol td (d) indicates the doubling time, td = ln2/µ, and Ng∗
247
is the net growth subtracted by the net growth measured in the test where no carbon was
248
supplied. This operation was performed in order to remove the effect of CO2 contained in
249
the headspace of the microcosm bottles.
250
As seen in this table and in parts a and d of Figure 4, the largest net growth is obtained for
251
200 mg/L of total carbon supplied, with the largest value when NaHCO3 was used as carbon 14
ACS Paragon Plus Environment
Page 14 of 31
Page 15 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Energy & Fuels
Table 2: Experimental conditions and growth parameters for the experiments run using microcosm bottles. Experiments 1 through 6 and 7 through 12 were run using NaHCO3 and MgCO3 -3H2 O, respectively. Exp C, # mg/L Ctrl 1 5 vol.% CO2 1 12 2 20 3 50 4 100 5 200 6 400 7 12 8 20 9 50 10 100 11 200 12 400
Ng∗ , µ, cells/mL 1/day 7.58·106 0.39 5 2.92·10 0.13 7.35·105 0.17 6 2.59·10 0.27 3.99·106 0.31 6 5.98·10 0.35 6 5.53·10 0.34 3.62·105 0.14 5 0.16 6.37·10 6 2.56·10 0.26 2.95·106 0.29 6 4.30·10 0.33 3.42·106 0.29
td , Ec , day % 1.77 5.14 26 4.00 40 2.58 56 2.25 43 2.01 32 2.03 15 5.05 47 4.31 50 2.68 80 2.36 62 2.12 34 2.36 13
252
source. Overall the growth rate increases with carbon concentration. However, the carbon
253
utilization efficiency (Ec ) increases until 50 mg/L of carbon concentration, indicating that
254
the supplied carbon is not all uptaken by the algae. In all tests pH increases, but the change
255
decreases with carbon concentration. This is because the cation concentration increases as
256
well with increasing carbon content and becomes the dominant species controlling the pH of
257
the system.
258
Figure 5 shows the color development in each microcosm bottle as well as microscopy
259
images of the microalgae at the end of the experiment. As illustrated by these images the
260
intensity of the green color of the suspension increases with carbon concentration. The bottles
261
of tests 1 through 6 express a more pronounced green color than those of tests 7 through 12.
262
This is because in the latter set of experiments, the microalgae settle towards the bottom of
263
the containers as the shaking was interrupted. As a matter of fact, in this case, the microalgae
264
acquire a cluster structure (images in part b of Figure 5) making them heavier and, therefore,
265
favoring settling. This type of behavior could be due to the presence of Mg2+ cations, which
266
interact with the negative charges of the microalgae membrane, compress the double layer 15
ACS Paragon Plus Environment
Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Figure 4: Microalgae tests in microcosm bottles. (a) through (c) carbon supplied by NaHCO3 ; (d) through (f) carbon supplied by MgCO3 -3H2 O.
16
ACS Paragon Plus Environment
Page 16 of 31
Page 17 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Energy & Fuels
267
favoring coagulation, as previously reported by Vandamme et al. 59 , Das et al. 60 , Xia et al. 61 .
268
Such as phenomenon is important to the practicality of the implementation of the overall
269
process, as fast settling can reduce significantly the cost of separation of the algae from the
270
solution.
Figure 5: Pictures of the microcosm bottles taken at the end of the tests and corresponding microscopy images of the microalgae. Microscopy pictures are a merge between the brightfield and the fluorescence image.
271
Growth of microalgae in a continuously-stirred batch reactor
272
Experiments in an open continuously-stirred batch reactor were conducted using different
273
sources of carbon, namely, atmospheric CO2 , NaHCO3 , and MgCO3 -3H2 O. The carbon
274
concentrations provided through the carbonate minerals were varied between 50 and 200
275
mg/L, which were selected on the basis of the best Ng∗ calculated from the experiments run 17
ACS Paragon Plus Environment
Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
276
in the closed microcosm bottles.
277
The applied experimental conditions are listed in Table 3 in conjunction with the es-
278
timates of the model parameters, namely, µmax , Ks , and Y , and the carbon utilization
279
efficiency (i.e., Ec ). The measurements of cell density, total dissolved carbon, and pH as
280
a function of culturing time are shown in Figure 6 and 7. The error bars for cell density
281
measurements shown in the corresponding panels were determined over four replicates. In
282
these figures, the optimized model is also shown. It is evident that the model catches very
283
well the evolution of the microalgae and the consumption of the substrate. The bottom
284
images were taken at end of the experimental time period. Table 3: Experimental conditions applied in experiments run in the continuously-stirred batch reactor and model parameter estimates. Experiments 13 through 17 and 18 through 24 were run using NaHCO3 and MgCO3 -3H2 O, respectively. Exp C, # mg/L 13 50 14 50 15 100 16 100 17 200 18 50 19 50 20 100 21 100 22 100 23 200 24 200
N source N-NH+ 4 N-NH+ 4 N-NH+ 4 N-NO− 3 N-NO− 3 N-NH+ 4 N-NH+ 4 N-NH+ 4 N-NH+ 4 N-NH+ 4 N-NO− 3 N-NO− 3
µmax , Ks , Y, Ec , 1/day mg/L (-) % 0.95 1.93 1.61 100 0.79 0.90 1.36 86 1.20 0.13 0.98 66 1.20 0.13 0.98 56 0.94 2.88 1.42 65 0.90 0.04 2.01 88 0.88 0.07 1.83 82 0.77 0.97 0.89 45 1.49 0.09 1.63 77 1.84 1.18 1.06 43 0.59 0.48 0.55 26 0.91 1.00 0.94 31
285
+ In these tests, two different sources of nitrogen were provided, either NO− 3 or NH4 . This
286
is because when NO− 3 was used, the pH increased up to 12, which is higher than the physi-
287
ological pH for algae, thus inhibiting their growth. Moreover, such an alkaline pH triggered
288
the precipitation of solid phases, such as, e.g., artinite, nesquehonite, and struvite 57,62 , which
289
limited nutrient availability to the algae. Algae uptake N as NH3 , transforming it either from
290
+ NO− 3 while consuming acidity or from NH4 while producing protons. In the former case, the
291
reaction favors the increase of the pH of the solution whereas in the latter case, the reaction 18
ACS Paragon Plus Environment
Page 18 of 31
Page 19 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Energy & Fuels
292
helps the system to balance the solution pH. As evident from the results reported in Table
293
3 and Figures 6 and 7, the concentration profiles in experiments 15 and 16, which were run
294
with the same initial amount of carbon but different source of nitrogen, are reproducible. As
295
expected, in exp. 15, a smaller variation of pH was recorded and lower pH adjustments were
296
required by using HCl, whereas in exp. 16, much larger pH oscillations occurred and more
297
frequent pH adjustments were necessary. This is because in the latter case more alkalinity
298
was present in the system and, therefore, the addition of an acidic solution was required to
299
control pH. Similar observations can be made for exp. 17, 23, and 24, where N was sup-
300
52 plied in the form of NO− showed that when growing S. obliquus on 3 . A previous study
301
ammonium using both atmospheric conditions and 5 vol.% CO2 as C sources, a significant
302
decrease in pH is observed resulting in the inhibition of growth unless the pH is adjusted.
303
Figures 2 and 3 in the SI document show the carbonate species in solution as a function of
304
pH during these experiments.
305
In all investigated conditions, the microalgae were able to grow at similar rates and the
306
maximum cell density reached at the end of the experimental time increases with the initial
307
carbon supplied. This is also qualitatively evident from the microscopy images reported at
308
the bottom of these figures, where it is possible to notice a more concentrated suspension
309
as the carbon increases. The model captures well the observed trend of both the growth of
310
the cells and the consumption of the substrate (parts a through j of Figures 6 and 7) and
311
the estimated values of the parameters are within those reported in the literature, 63 with
312
the values of µmax , Ks , and Y changing within 0.6–1.8 1/day, 0.13–3 mg/L, and 0.55–2.01,
313
respectively. The average value for µmax , Ks , and Y for NaHCO3 and MgCO3 -3H2 O are 1.02
314
1/day, 1.19 mg/L, 1.27 and 1.05 1/day, 0.55 mg/L, 1.27, respectively. Moreover, the carbon
315
efficiency reaches values up to 80–100 %. Such a high values of Ec was calculated in the tests
316
(namely, exp. 13, 14, 18, and 19) where the lowest carbon concentration was supplied, i.e.,
317
50 mg/L, indicating a deficiency of carbon provided to the system, in contrast to the other
318
experiments, where larger carbon concentration was supplied. Here, the value of Ec varies
19
ACS Paragon Plus Environment
Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Figure 6: Cell density, total dissolved carbon, and pH during the culturing time of microalgae using NaHCO3 as carbon source. Dots are the measurements and the lines refer to the bestfit with the model. The microscopy images were taken at the end of the tests, i.e., after 7 days.
20
ACS Paragon Plus Environment
Page 20 of 31
Page 21 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Energy & Fuels
Figure 7: Cell density, total dissolved carbon, and pH during the culturing time of microalgae using MgCO3 -3H2 O as carbon source. Dots are the measurements and the lines refer to the best-fit with the model. The microscopy images were taken at the end of the tests, i.e., after 7 days.
21
ACS Paragon Plus Environment
Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
319
within a large range of 26–77 %. In future work, we will study how to optimize the carbon
320
supply to obtain the best growth while meeting the requirement of carbon fixation.
Figure 8: Comparison of the net growth as a function of time measured in our work and in the literature where 5 vol.% of CO2 64 and direct flue-gas with 0.5 vol.% 64 and 20 vol.% 65 were supplied 64,65 .
321
Finally, Figure 8 shows a comparison between the results from this work, where the
322
highest growth was recorded, and literature data where carbon was provided to Scenedesmus
323
sp. as gaseous CO2 64,65 . Details about the tests from the literature are reported in Table 1
324
of the SI document. As evident from this diagram, our data compare well with the literature
325
in an early stage of algae growth reaching a plateau after 5 days of culture. This could be
326
due to the complete consumption of the supplied carbon to the system. Supply of mineral in
327
a series of steps coupled with the removal of cation might be therefore required to increase
328
the net growth.
22
ACS Paragon Plus Environment
Page 22 of 31
Page 23 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Energy & Fuels
329
Conclusions
330
In this paper, a process combining mineral carbonation and microalgae (i.e., Scenedesmus
331
obliquus) growth for biomass production was presented. The process consists of a carbon
332
capture step and subsequent carbon reuse for algae growth through its release by dissolution
333
of the carbonate minerals, e.g., nahcolite (NaHCO3 ) and nesquehonite (MgCO3 -3H2 O) at
334
atmospheric conditions. The cell density within the algae biomass was determined using
335
fluorescence measurements. Batch tests show that microalgae grow well under the applied
336
conditions, with a better yield when NaHCO3 was supplied to the system. The measure-
337
ments were described adequately by a bio-chemical model, implemented in this work and
338
the estimated growth kinetics compares well with those in the the literature.
339
Overall, this paper demonstrates that carbonate species can be provided for algae growth
340
as an alternative option to the conventional one of direct gaseous CO2 injection. This method
341
can be particularly useful for algae production sites where gaseous carbon dioxide is not
342
available from nearby sources. To the best of the authors knowledge, this is the first study
343
where carbon utilization for biomass production, mediated through mineral carbonation, has
344
been investigated.
345
Acknowledgement
346
This work was supported by the Consortium for Energy, Environment and Demilitarization
347
(CEED) contract number SINIT-15-0013. The authors would like to thank the undergrad-
348
uate student Sarah Chan for helping in part of the laboratory work reported here. The
349
authors would like to thank also two anonymous reviewers that with their comments helped
350
improving the manuscript.
23
ACS Paragon Plus Environment
Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
351
Supporting Information Available
352
A supporting information document is included and contains additional information regard-
353
ing this work.
354
References
355
(1) Dlugokencky, E.; Tans, P. Trends in atmospheric carbon dioxide, National Oceanic At-
356
mospheric Administration, Earth System Research Laboratory (NOAA/ESRL). 2018,
357
(2) Le Qu´er´e, C. et al. Global Carbon Budget 2017. Earth Syst. Sci. Data 2018, 10, 405–
358
448.
359
(3) Crowley, T. J.; Berner, R. A. CO2 and Climate Change. Science 2001, 292, 870–872.
360
(4) Arthur, M. A.; Dean, W. E.; Schlanger, S. O. The Carbon Cycle and Atmospheric
361
CO2 : Natural Variations Archean to Present; American Geophysical Union, 2013; pp
362
504–529.
363
(5) The Paris Agreement. United Nations, version of 22 October 2018.
364
(6) Clarke, L.; Jiang, K. Assessing transformation pathways Climate Change 2014: Miti-
365
gation of Climate Change. Contribution of Working Group III to the Fifth Assessment
366
Report of the Intergovernmental Panel on Climate Change. 2014.
367
(7) Metz, B.; Davidson, O.; de Coninck, H.; Loos, M.; Meyer, E., L. IPCC Special Report
368
on Carbon Dioxide Capture and Storage; Intergovernmental Panel on Climate Change.
369
2005.
370
(8) Leung, D. Y.; Caramanna, G.; Maroto-Valer, M. M. An overview of current status of
371
carbon dioxide capture and storage technologies. Renewable Sustainable Energy Rev.
372
2014, 39, 426–443. 24
ACS Paragon Plus Environment
Page 24 of 31
Page 25 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
373
374
375
376
Energy & Fuels
(9) Rubin, E. S.; Davison, J. E.; Herzog, H. J. The cost of CO2 capture and storage. Int J Greenh Gas Con 2015, 40, 378–400. (10) Clarke, L.; et al., Update on Utilization or Storage of CO2 Through Chemical, Biological, or Mineral Conversion. 2013.
377
(11) Cu´ellar-Franca, R. M.; Azapagic, A. Carbon capture, storage and utilisation technolo-
378
gies: A critical analysis and comparison of their life cycle environmental impacts. J.
379
CO2 Util. 2015, 9, 82–102.
380
(12) Pi, S.; Zhang, Z.; He, D.; Qin, C.; Ran, J. Novel Binders-Promoted Extrusion-
381
Spheronized CaO-Based Pellets for High-Temperature CO2 Capture. Energy Fuels
382
2019, 33, 2381–2389.
383
(13) Pan, S.; Chiang, A.; Chang, E.; Lin, Y.; Kim, H.; Chiang, P. An innovative approach
384
to integrated carbon mineralization and waste utilization: A review. Aerosol Air Qual
385
Res 2015, 15, 1072–1091.
386
(14) Pan, S.-Y.; Ling, T.-C.; Park, A.-H. A.; Chiang, P.-C. An Overview: Reaction Mech-
387
anisms and Modelling of CO2 Utilization via Mineralization. Aerosol and Air Quality
388
Research 2018, 18, 829–848.
389
390
391
392
393
394
395
(15) Gadikota, G.; hyung Alissa Park, A. In Carbon Dioxide Utilisation; Styring, P., Quadrelli, E. A., Armstrong, K., Eds.; Elsevier: Amsterdam, 2015; pp 115–137. (16) Dur´an, I.; Rubiera, F.; Pevida, C. Microalgae: Potential precursors of CO2 adsorbents. J. CO2 Util. 2018, 26, 454–464. (17) Sayre, R. Microalgae: The Potential for Carbon Capture. BioScience 2010, 60, 722– 727. (18) Razzak, S. A.; Hossain, M. M.; Lucky, R. A.; Bassi, A. S.; de Lasa, H. Integrated
25
ACS Paragon Plus Environment
Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
396
CO2 capture, wastewater treatment and biofuel production by microalgae culturing–A
397
review. Renewable Sustainable Energy Rev. 2013, 27, 622–653.
398
(19) Kan, T.; Grierson, S.; de Nys, R.; Strezov, V. Comparative Assessment of the Thermo-
399
chemical Conversion of Freshwater and Marine Micro- and Macroalgae. Energy Fuels
400
2014, 28, 104–114.
401
(20) Muratori, M.; Calvin, K.; Wise, M.; Kyle, P.; Edmonds, J. Global economic conse-
402
quences of deploying bioenergy with carbon capture and storage (BECCS). Environ.
403
Res. Lett. 2016, 11, 095004.
404
405
(21) Pires, J. C. M. Recent advances in renewable energy; Betham Science Publisher Ltd., 2017.
406
(22) Tang, D.; Han, W.; Li, P.; Miao, X.; Zhong, J. CO2 biofixation and fatty acid compo-
407
sition of Scenedesmus obliquus and Chlorella pyrenoidosa in response to different CO2
408
levels. Bioresour. Technol. 2011, 102, 3071–3076.
409
(23) Liao, Q.; Chang, H.-X.; Fu, Q.; Huang, Y.; Xia, A.; Zhu, X.; Zhong, N. Physiological-
410
phased kinetic characteristics of microalgae Chlorella vulgaris growth and lipid synthesis
411
considering synergistic effects of light, carbon and nutrients. Bioresour. Technol. 2018,
412
250, 583–590.
413
(24) Beal, C. M.; Gerber, L. N.; Sills, D. L.; Huntley, M. E.; Machesky, S. C.; Walsh, M. J.;
414
Tester, J. W.; Archibald, I.; Granados, J.; Greene, C. H. Algal biofuel production for
415
fuels and feed in a 100-ha facility: A comprehensive techno-economic analysis and life
416
cycle assessment. Algal Res 2015, 10, 266–279.
417
(25) Hernndez-Calder´on, O. M.; Ponce-Ortega, J. M.; Ortiz-del Castillo, J. R.; Cervantes-
418
Gaxiola, M. E.; Mil´an-Carrillo, J.; Serna-Gonz´alez, M.; Rubio-Castro, E. Optimal
419
Design of Distributed Algae-Based Biorefineries Using CO2 Emissions from Multiple
420
Industrial Plants. Ind. Eng. Chem. Res. 2016, 55, 2345–2358. 26
ACS Paragon Plus Environment
Page 26 of 31
Page 27 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Energy & Fuels
421
(26) Hu, P.; Chakraborty, S.; Kumar, A.; Woolston, B.; Liu, H.; Emerson, D.; Stephanopou-
422
los, G. Integrated bioprocess for conversion of gaseous substrates to liquids. Proc. Natl.
423
Acad. Sci. U. S. A. 2016, 113, 3773–3778.
424
(27) Salama, E.-S.; Hwang, J.-H.; El-Dalatony, M. M.; Kurade, M. B.; Kabra, A. N.; Abou-
425
Shanab, R. A. I.; Kim, K.-H.; Yang, I.-S.; Govindwar, S. P.; Kim, S.; Jeon, B.-H.
426
Enhancement of microalgal growth and biocomponent-based transformations for im-
427
proved biofuel recovery: A review. Bioresour. Technol. 2018, 258, 365–375.
428
(28) De Bhowmick, G.; Sarmah, A. K.; Sen, R. Zero-waste algal biorefinery for bioenergy
429
and biochar: A green leap towards achieving energy and environmental sustainability.
430
Sci. Total Environ. 2019, 650, 2467–2482.
431
(29) Zheng, Q.; Xu, X.; Martin, G. J.; Kentish, S. E. Critical review of strategies for CO2
432
delivery to large-scale microalgae cultures. Chinese Jour. Chem. Eng. 2018, 26, 2219–
433
2228.
434
(30) J. Theo M. Elzenga, J. S., Hidde B. A. Prins The role of extracellular carbonic anhydrase
435
activity in inorganic carbon utilization of Phaeocystis globosa (Prymnesiophyceae): A
436
comparison with other marine algae using the isotopic disequilibrium technique. Limnol.
437
Oceanogr 2000, 45, 372–380.
438
(31) Najafabadi, H. A.; Malekzadeh, M.; Jalilian, F.; Vossoughi, M.; Pazuki, G. Effect of
439
various carbon sources on biomass and lipid production of Chlorella vulgaris during
440
nutrient sufficient and nitrogen starvation conditions. Bioresour. Technol. 2015, 180,
441
311–317.
442
(32) Pancha, I.; Chokshi, K.; Ghosh, T.; Paliwal, C.; Maurya, R.; Mishra, S. Bicarbonate
443
supplementation enhanced biofuel production potential as well as nutritional stress
444
mitigation in the microalgae Scenedesmus sp CCNM 1077. Bioresour. Technol. 2015,
445
193, 315–323. 27
ACS Paragon Plus Environment
Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
446
(33) Findenegg, G. R. Correlations between Accessibility of Carbonic Anhydrase for Exter-
447
nal Substrate and Regulation of Photosynthetic Use of CO2 and HCO3- by Scenedesmus
448
obliquus. Z. Pflanzenphysiol. 1976, 79, 428–437.
449
(34) Gardner, R. D.; Cooksey, K. E.; Mus, F.; Macur, R.; Moll, K.; Eustance, E.; Carl-
450
son, R. P.; Gerlach, R.; Fields, M. W.; Peyton, B. M. Use of sodium bicarbonate
451
to stimulate triacylglycerol accumulation in the chlorophyte Scenedesmus sp. and the
452
diatom Phaeodactylum tricornutum. J. Appl. Phycol. 2012, 24, 1311–1320.
453
(35) Gardner, R. D.; Lohman, E.; Gerlach, R.; Cooksey, K. E.; Peyton, B. M. Compari-
454
son of CO2 and bicarbonate as inorganic carbon sources for triacylglycerol and starch
455
accumulation in Chlamydomonas reinhardtii. Biotechnol. Bioeng. 2013, 110, 87–96.
456
(36) White, D. A.; Pagarette, A.; Rooks, P.; Ali, S. T. The effect of sodium bicarbonate
457
supplementation on growth and biochemical composition of marine microalgae cultures.
458
J. Appl. Phycol. 2013, 25, 153–165.
459
(37) Oliver, T. K.; Farhang, F.; Hodgins, T. W.; Rayson, M. S.; Brent, G. F.; Molloy, T. S.;
460
Stockenhuber, M.; Kennedy, E. M. CO2 Capture Modeling Using Heat-Activated Ser-
461
pentinite Slurries. Energy Fuels 2019, 33, 1753–1766.
462
(38) Teir, S.; Kuusik, R.; Fogelholm, C.-J.; Zevenhoven, R. Production of magnesium car-
463
bonates from serpentinite for long-term storage of CO2 . Int. J. Miner. Process. 2007,
464
85, 1–15.
465
(39) H¨anchen, M.; Prigiobbe, V.; Baciocchi, R.; Mazzotti, M. Precipitation in the Mg-
466
carbonate system effects of temperature and CO2 pressure. Chem. Eng. Sci. 2008, 63,
467
1012–1028.
468
469
(40) Prigiobbe, V.; Mazzotti, M. Precipitation of Mg-carbonates at elevated temperature and partial pressure of CO2 . Chem. Eng. J. 2013, 223, 755–763.
28
ACS Paragon Plus Environment
Page 28 of 31
Page 29 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
470
471
472
473
Energy & Fuels
(41) Prigiobbe, V. Estimation of nucleation and growth parameters from in situ Raman spectroscopy in carbonate systems. J. Environ. Chem. Eng. 2018, 6, 930–936. (42) Rahmani, O. CO2 sequestration by indirect mineral carbonation of industrial waste red gypsum. J. CO2 Util. 2018, 27, 374–380.
474
(43) Liu, M.; Gadikota, G. Integrated CO2 Capture, Conversion, and Storage To Produce
475
Calcium Carbonate Using an Amine Looping Strategy. Energy Fuels 2019, 33, 1722–
476
1733.
477
(44) Oliver, T. K.; Dlugogorski, B. Z.; Kennedy, E. M. Biologically enhanced degassing and
478
precipitation of magnesium carbonates derived from bicarbonate solutions. Miner. Eng.
479
2014, 61, 113–120.
480
(45) Glasser, F. P.; Jauffret, G.; Morrison, J.; Galvez-Martos, J.-L.; Patterson, N.; Im-
481
babi, M. S.-E. Sequestering CO2 by Mineralization into Useful Nesquehonite-Based
482
Products. Front. Energy Res. 2016, 4, 3.
483
484
485
486
(46) Power, I. M.; Harrison, A. L.; Dipple, G. M. Accelerating Mineral Carbonation Using Carbonic Anhydrase. Environ. Sci. Technol. 2016, 50, 2610–2618. (47) Hariharan, S.; Mazzotti, M. Growth Kinetics of Synthetic Hydromagnesite at 90◦ C. Cryst. Growth Des. 2017, 17, 317–327.
487
(48) Mun, S.; Han, S.; Wee, J. Carbon Dioxide Fixation by Precipitating NaHCO3 via
488
Carbonation of NaOH-Dissolved Ethanol Aqueous Solution. Energy Fuels 2018, 32,
489
8614–8622.
490
(49) Shim, J.-G.; Lee, D. W.; Lee, J. H.; Kwak, N.-S. Experimental study on capture of
491
carbon dioxide and production of sodium bicarbonate from sodium hydroxide. Environ.
492
Eng. Res. 2016, 21, 297–303.
29
ACS Paragon Plus Environment
Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
493
(50) Parkhurst, D. L.; Appelo, C. A. J. Description of input and examples for PHREEQC
494
version 3–A computer program for speciation, batch-reaction, one-dimensional trans-
495
port, and inverse geochemical calculations. 2013.
496
(51) Database Administration Guide. version JADE 7.1.08, 2016.
497
(52) Eustance, E.; Gardner, R. D.; Moll, K. M.; Menicucci, J.; Robin Gerlach, B. M. P.
498
Growth, nitrogen utilization and biodiesel potential for two chlorophytes grown on
499
ammonium, nitrate or urea. J.Appl.Phycol. 2013, 25, 1663–1677.
500
(53) Abraham, J.; Lin, Y.; RoyChowdhury, A.; Christodoulatos, C.; Conway, M.; Smolin-
501
ski, B.; Braida, W. Algae toxicological assessment and valorization of energetic-laden
502
wastewater streams using Scenedesmus obliquus. J. Cleaner Prod. 2018, 202, 838–845.
503
(54) Absher, M. In Tissue Culture; Kruse, P. F., Patterson, M., Eds.; Academic Press, 1973;
504
505
506
Chapter 1, pp 395–397. (55) Mersmann, A. Crystallization Technology Handbook, 2nd ed.; Marcel Dekker Inc.: New York, 2001.
507
(56) MathWorks, MATLAB R2014b. http://www.mathworks.com/, 2014.
508
(57) Tansel, B.; Lunn, G.; Monje, O. Struvite formation and decomposition characteristics
509
for ammonia and phosphorus recovery: A review of magnesium-ammonia-phosphate
510
interactions. Chemosphere 2018, 194, 504–514.
511
(58) Gorain, P. C.; Bagchi, S. K.; Mallick, N. Effects of calcium, magnesium and sodium
512
chloride in enhancing lipid accumulation in two green microalgae. Environ. Technol.
513
2013, 34, 1887–1894, PMID: 24350442.
514
(59) Vandamme, D.; Foubert, I.; Muylaert, K. Flocculation as a low-cost method for harvest-
515
ing microalgae for bulk biomass production. Trends in Biotechnol. 2013, 31, 233–239.
30
ACS Paragon Plus Environment
Page 30 of 31
Page 31 of 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Energy & Fuels
516
(60) Das, P.; Thaher, M. I.; Hakim, M. A. Q. M. A.; Al-Jabri, H. M. S.; Alghasal, G.
517
S. H. Microalgae harvesting by pH adjusted coagulation-flocculation, recycling of the
518
coagulant and the growth media. Bioresour. Technol. 2016, 216, 824–829.
519
520
(61) Xia, L.; Li, Y.; Huang, R.; Song, S. Effective harvesting of microalgae by coagulationflotation. R. Soc. open sci. 2017, 4, 170867.
521
(62) Stolzenburg, P.; Capdevielle, A.; Teychene, S.; Biscans, B. Struvite precipitation with
522
MgO as a precursor: Application to wastewater treatment. Chem. Eng. Sci. 2015, 133,
523
9–15.
524
525
(63) Lee, E.; Jalalizadeh, M.; Zhang, Q. Growth kinetic models for microalgae cultivation: A review. Algal Res 2015, 12, 497–512.
526
(64) Chandra, T. S.; Deepak, R.; Kumar, M. M.; Mukherji, S.; Chauhan, V.; Sarada, R.;
527
Mudliar, S. Evaluation of indigenous fresh water microalga Scenedesmus obtusus for
528
feed and fuel applications: Effect of carbon dioxide, light and nutrient sources on growth
529
and biochemical characteristics. Bioresour. Technol. 2016, 207, 430–439.
530
(65) Li, F.-F.; Yang, Z.-H.; Zeng, R.; Yang, G.; Chang, X.; Yan, J.-B.; Hou, Y.-L. Microalgae
531
Capture of CO2 from Actual Flue Gas Discharged from a Combustion Chamber. Ind.
532
Eng. Chem. Res. 2011, 50, 6496–6502.
31
ACS Paragon Plus Environment