Plastics, Rubber, and Paper Recycling - American Chemical Society

machine designed to get the maximum performance from recovered fiber. Paper products ranging from ..... A high speed rotating drum imparts a high cent...
0 downloads 0 Views 2MB Size
Chapter 26

Advances in Paper Fiber Recycling: Meeting the Challenge

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

Bruce W. Janda Neenah Technical Center, James River Corporation, P.O. Box 899, Neenah, WI 54957-0899

Cellulose fiber (paper) accounts for 34% of the weight of materials sent to landfill in the United States. The paper industry recently exceeded its goal of recovering and reusing 40% of the fiber produced and has set a new goal of 50%. This high recovery level presents both challenges and opportunities. It requires using a much wider variety of materials, while improving product performance and value. James River is meeting the challenge with several projects now on-line. A new process for using 100% waste paper to produce recycled paperboard for packaging provides capability to independently process multiple sources of recovered materials to remove contaminants without the costs of a deinking system. These highly cleaned feedstocks are delivered to a multilayer paper machine designed to get the maximum performance from recovered fiber. Paper products ranging from newspapers and packaging materials to towels and tissues are the most familiar disposables. Paper is the most common packaging material, utilized in 48% of all packaging (1) and is made from a renewable raw material that is in abundance in North America. However, concern has grown over the ability to site new landfills to sustain the rate of trash generation and disposal. Cellulose fiber, in the form of paper and paperboard, accounted for 34% by weight of municipal solid waste discards in an 1988 EPA study (2). In a time of increased concern over landfill disposal, it is not surprising that recycling of paper fiber should receive so much attention from consumers, the paper industry, producers of packaged goods, and municipalities. Consumers have begun to expect that their paper products and paper packaging be made, at least in part, from recycled fiber. The American Forest and Paper Association has responded by meeting its initial goal of recovering and reusing 40% of the fiber produced. Recovery rates for different paper products range from more than 50% of newspapers published and 60% of old corrugated containers to 33% of all paper and paperboard packaging (3). A new goal of 50% recovery by the year 2000 has been set. It is expected that achieving these high recycling rates will result in fiber strength degradation and increased levels of contaminants in the new waste paper 0097-6156/95/0609-0306$12.00/0 © 1995 American Chemical Society In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

26.

JANDA

Advances in Paper Fiber Recycling

307

sources. At the same time, consumer expectations for product and packaging performance continue to increase. Increased performance in packaging often means maintaining strength and function at lower basis weights to reduce the amount of packaging waste at its source. Packaging performance is important to prevent waste, damage or spoilage of the protected product. Increasing both the fiber recovery rate and the performance of recycled products presents a significant challenge. The purpose of this paper is to review the practical complexity of one area of paper fiber recycling and how James River Corporation is meeting this challenge by implementing projects with improved technology.

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

Challenges The Effect of Recycling on Fiber Properties. Paper fibers have a tubular structure that results in a higher strength to weight ratio than steel, aluminum, or glass. One challenge to increasing the recovery rate of paper fibers is the tendency of the fibers to be weakened with repeated recycling. Some processors avoid the recovery of corrugated cartons from electronics packaging originating in Asia as they have already been recycled four or five times and exhibit a noticeable strength loss. The recycling process rehydrates the fiber and then mechanically stresses it as it is cleaned, refined, formed, pressed, and redded. Each recycling process results in loss of some polysaccharides, and the breakdown of some cellulose into low molecular weight fragments and fine pieces of the fiber that cannot be formed into a web and are lost in the process water (4). In addition, many of the additives contained in paper, such as clay coatings and inks, must be removed in the recycling process. This tends to reduce fiber strength and increase the volume of rejected material destined for the landfill. A recent study of the effect of recycling on chemical properties of pulp concluded that repeated recycling results in only minor chemical changes in the fibers. This means that chemical analysis cannot be "used as a tool for differentiating between virgin and recycled fibers" (5). The loss of strength properties with repeated recycling is better associated with physical changes to the fibers. Howard and Bichard conducted a study of recycling effects on pulp physical properties showing that fiber length was little affected. Repeated recycling generated fines that when included in an arithmatic average of fiber length, tended to unfairly skew results found in the literature (1). The individual strength of fibers was unaffected by recycling, again indicating little structural change in the cellulose polymer. However, the bonding potential of the fibers was affected by recycling resulting in changes to the strength of paper produced. This bonding strength is controlled by the fiber-to-fiber contact area and is a result of hydrogen bonding. Figure 1 shows a comparison of 100% recycled fibers with typical virgin chemical pulp fibers. These are light microphotographs at 100 times magnification. Increased fiber damage and debris are seen in the recycled furnish. The fiber physical changes associated with paper recycling were found to depend on the class or source of the fiber. Chemical pulps in products such as white office papers or brown corrugated boxes tend to lose their natural high bonding potential as the swelling or rehydration of the fibers is reduced with recycling. The fibers experience "hornification," tending to close up and become less conformable with repeated recycling, interfering with fiber-to-fiber hydrogen bonding. Sheet bulk may increase when recycling chemical pulps. Mechanical pulps found in products such as newsprint tend to increase their otherwise low bonding potential with recycling as the fibers are flattened and become more flexible. Sheet bulk using these pulps tends to decrease with recycling. These opposite effects for chemical and mechanical pulps do not cancel each other out in the production of a recycled product containing both classes of

In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

308

PLASTICS, RUBBER, AND PAPER RECYCLING

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

pulps. Chemical pulps are much stronger than the mechanical, and therefore a net strength loss is expected with repeated recycling. The ability to handle the different fiber classes separately represents an advantage to minimizing fiber damage and strength loss expected with increased recycling. The paper forming systems must be optimized to get the most performance possible out of the weaker fiber furnish. As we move to meet the challenge of recovering 50% of the fiber produced, we will be increasingly recycling already recycled fibers.

Figure 1. 100X Microphotographs Fiber Contamination. Recycled paper mills have long had to deal with staples, paper clips, glue, tape, plastics, dirt, and many other unwanted contaminants. Increased recovery rates also can be expected to increase the amount of contaminants in the waste paper supply stream. Recycling processes work best on a steady supply of clean and homogeneous materials. In the past, recycled paper materials were obtained from industrial sources as overrun stock, misprinted materials, and box clippings. They are homogeneous, in that the contaminants are consistent and in small amounts. These relatively clean "pre-consumer" waste materials are already included in the national recovery rates achieved. Increasing the fiber recovery rate requires additional use of "post-consumer" or post-use waste that is contaminated with a wide variety of materials and requires more extensive treatment and cleaning. Competition for clean fiber sources will require the use of more contaminated materials. Meeting the 50% fiber recovery challenge will require improved systems for cleaning. Again, separate processing and treatment for the different fiber classes is needed to achieve the best cleanliness with the least fiber damage. Recycled Product Quality. Traditionally, products made from recycled materials carried the connotation of inferior quality and performance as opposed to products made from virgin or new materials. Recycled products were used where lower performance and cleanliness could be tolerated in return for lower costs. Now

In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

26. JANDA

Advances in Paper Fiber Recycling

309

consumer expectations of recycled products are changing dramatically toward equal performance to virgin materials. Experience in consumer paper goods shows consumers interested in recycled products demand both high recycled contents and high performance. This is a challenge as waste paper sources become increasingly contaminated and recycled fibers become weaker. Packaging design is also affected as concern over waste generation from packaging leads to "source reduction." This is an attempt to reduce the amount of packaging material required through increased material performance and corresponding reductions in basis weight. Again, this is a challenge for paper based packaging as recycled fibers lose their strength. As a result, recycled paperboard is often 20% heavier than virgin paperboard to maintain the same strength specification. A study by Arthur D. Little, Inc. stated this challenge clearly: "The challenge for the paper packaging industry is to use as much waste material as possible in packaging while still meeting the user's requirements for strength, protection, and other criteria. To be successful over the long term, products and packaging made from wastepaper must compete with virgin fiber products. Short-term 'fad sales to exploit the green marketing trend will not secure long-term markets." (7). 1

Recycling Benefits. Recycling of paper fibers offers many benefits in spite of the abundant supply of wood resources in North America. The Arthur D. Little, Inc. study also found that recycling a unit of paper can reduce air pollution by 74% and water pollution by 35% over producing virgin fibers. Recycling and deinking can save 15% of the water required for virgin production. A recycling process that does not require deinking can save 50% of the water. These are average results that can vary widely at individual sites. Not all forms of paper recycling are economically effective. The costs of processing some fibers into high performance products can be higher than producing virgin products. Some government recycled purchasing mandates allow a 10-15% price premium for recycled products in competitive bidding. The challenge is to improve the recycling process to reduce costs and to focus on paper grades that fit well with recycled fiber. Recycled paperboard is a special case. This product has been produced from old newspapers and corrugated boxes for a long time. Over half of the folding cartons or boxes on the supermarket shelf are made from 100% recycled fiber. The cost is lower than virgin as there is no deinking process step required, and the recovered materials are used efficiently. The white printing surface is generated by applying a pigmented coating. However, the challenges stated still apply. Maintaining cleanliness and strength performance while reaching deeper into the pool of waste material requires process upgrades. Meeting the increased demand for high performance 100% recycled packaging requires an improved paperboard for items that have traditionally relied on virgin fiber. K-l Recycler Project Project Description. James River approved funding of a project to rebuild the K-5 paperboard machine at Kalamazoo, Michigan, in August of 1990. The new paperboard machine components were built around the existing K-5 multiple cylinder machine, allowing its operations to continue for 75% of the construction time (8). The new process began operations in November of 1992 as the K - l Recycler. This $120 million rebuild added major capabilities to meet the challenge of providing a world class system for the production of high performance 100% recycled paperboard. A state-of-the-art facility for processing and cleaning recycled fiber was constructed that allows each class of recycled fiber to be treated separately. A triple fourdrinier forming section replaced the cylinder formers to

In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

310

PLASTICS, RUBBER, AND PAPER RECYCLING

provide improved control over formation and resultant physical properties of the paperboard. The pressing and drying systems were replaced to support the increased productivity of the new system. A networked computer system for process control and quality data was added to provide the operators with real-time data, graphical representations of the process, and the ability to implement advanced controls. A simplified flow diagram of the K - l paperboard production process is shown in Figure 2. This conceptual view of the process does not show the multiple fiber processing streams and the three layer forming systems. Screening Cleaning Refining Dilution

Forming

Pressing Drying

Coating

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

Paperboard Product

Figure 2. K - l Recycler Simplified Process Flow Diagram The new K - l Recycler is capable of producing up to 680 metric tons per day of PaceSetter® 100% recycled paperboard. Two main grades are produced: a grayback product with a light gray color from newspaper in the bottom liner, and a whiteback product with office paper in the bottom liner. Top coatings and surfaces are formulated for both gravure and lithographic printing applications. The product basis weights and thicknesses produced range from 254 g/m2 (52 lb/1000ft2)and 305^m (12 pt) to 469 g/m2 (96 lb/1000 ft2) and 610 ^m (24 pt). Fiber Sources. Fiber is received in a 9,000 square meter processing center located almost one half kilometer from the K - l former. An average production day requires the unloading of 26 semitrailers. Production of a quality product begins with prescreening of material by fiber brokers at their facilities. Communication between plant operators and the brokers as to runnability and contaminants results in continuous improvements in waste paper quality. A contract with a large food store chain to recover "OCC" or the old corrugated containers used for food shipment and storage provides a consistent source of quality fiber. Similar arrangements exist for the delivery of old newspapers. The K - l complex has four separate process systems to receive and process waste fiber. Each system is tailored to process and clean a specific fiber class. This increased versatility allows the process to be optimized to get the most effective cleaning while minimizing fiber damage and losses. Thefibersources and properties for each of the four processing systems are shown in Table I. The freeness (ml CSF units) is a measure of the tendency of the stock to drain or release water with a higher value indicating faster drainage. The Kajaani fiber length (mm) is an optical measurement of the fiber length in dilute solution. The Kajaani fines is the percentagefiberswith a length less than 0.2 mm. The topliner process system provides a smooth and white colored surface for coating application. The top liner fiber furnish is also used for the back side in whiteback production. Typical sources are envelopes, computer forms, catalogs, sales literature, and other office papers.

In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

26. JANDA

Advances in Paper Fiber Recycling

311

TABLE I. K-l Recycler Fiber Sources Average Fiber Properties %

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

Fiber Class & Sources Top Liner Process Svstem Colored Envelope Cuttings Manifold White Ledger Groundwood Computer Output Unprinted Bleached Kraft

Furnish

Freeness ml CSF

Kajaani Fiber Length mm

Kajaani Fines %

25 25 25 25

398 327 248 503

2.1 2.0 2.1 1.6

1A

100

151

2.1

9.3

100

588

2.5

6.8

100

430

2.1

8.5

7.5 8.8

News Process System

Old Newspapers OCC Process Svstem Old Corrugated Containers BQXSHQP

- Process System

Baled Carton Plant Waste (Paperboard Cuttings)

The news system processes old newspapers. This is a one-component system optimized for this feed source. The news furnish is split and used for both the middle filler and back side (backliner) of the product. The ink is not removed providing a uniform light gray color. The mechanical pulps used in the production of newsprint provide a low freeness pulp with relatively high fines content. These fibers tend to be rigid, kinked, and curled providing some product bulk. The OCC process system is also optimized for one furnish. The old corrugated containers are made from chemical fibers that drain more quickly. The increased fiber length and good bonding characteristics of this fiber source make this fiber class important for strength generation in the product. OCC is used in the middle filler layer. The boxshop system processes returned product cuttings from the paperboard converting process. This paperboard recycle stream is used in the middle filler ply. Fiber Preparation and Cleaning. Mixed in with the fibers received are contaminants, such as sand, metal, tapes, waxes, plastics, glues, adhesives, and dirt. These contaminants could be from the original paper product, picked up in use, or from the collection process. They must be removed to produce a clean, high strength product and maintain productivity in the forming and coating process. The challenge of the fiber preparation process is high efficiency separation of the contaminants from the fiber while minimizing fiber losses. The intensity of the cleaning process must be controlled to prevent fiber damage and strength degradation. The K - l process meets this challenge by providing four different fiber preparation processes. The fiber entering each of the four systems is repulped at about 4-5% solids with water in large continuous pulpers. Mechanical action of the pulper rotor and

In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

312

PLASTICS, RUBBER, AND PAPER RECYCLING

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

associated hydraulic forces separate the waste paper into individual fibers in preparation for screening and cleaning. High density cleaners after the pulpers remove heavy contaminants. The fiber is then sent to the screening system to remove contaminants based on size and shape. The fiber and water slurry is pumped through a series of hole and slotted screens at 2-4% solids where debris larger than the screen size is concentrated into a reject stream for further processing. Hole screens tend to remove long debris, and the slotted screens remove cubical debris while allowing fiber to pass. The screens are arranged in a cascaded flow system to rescreen rejects and minimize fiber losses. Figure 3 shows the screen size and process flow for the topliner system. 3-stoye 1.6 mm hole Screens Feed • • , 1 1 - ^ 2 ^ 3 -Rejects to common system Reject screening Accepts 3-stage 0.25 mm slotted screens l

2

1

•* 3

-Rejects to common system

Screened Stock Figure 3. Topliner System Screening Process Fiber and debris would tend to block the holes or slots with time and blind the screen, restricting flows if counter measures were not available. To facilitate debris removal, the screens contain a rotating foil to create a temporary back pulse in the screen flow to remove debris blocking the screen and move them to the reject line (9). A conceptual diagram of the cleaning foil is shown in Figure 4. The OCC system has additional equipment to remove small lightweight contaminants that may pass the screens. These contaminants include polystyrene foams (e.g., Styrofoam™), wax, pressure sensitive adhesives, and fine plastics. Cleaning technology for separating the fiber from these materials relies on the density difference between cellulose fibers and the contaminants. The specific gravity of fiber is about 1.2 when the cellulose is swelled by water. The contaminants listed typically have a specific gravity less than 1.0. Two Gyrocleaners are used to separate contaminants from the OCC fiber. A conceptual diagram of a Gyrocleaner is shown in Figure 5. A high speed rotating drum imparts a high centrifugal force to the slurry, allowing separation of the lighter contaminants. The Gyroclean system generates separation forces up to 700X gc, resulting in much greater cleaning efficiency at much higher solids and lower fiber loses than traditional reverse cleaners (10). Rejected material from the screening processes is sent to a common reject processing system. A series of hole and slotted screens separate good fiber from the contaminants. The contaminants are removed from the process for disposal, and the recovered fiber is sent back to be reprocessed by the OCC screening system. This extra cleaning step insures that good fiber is not discarded while maintaining product cleanliness. In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

26. JANDA

Advances in Paper Fiber Recycling

313

Figure 4. Foil Action in a Pressure Screen (Reproduced with permission from ref. 9. Copyright 1993 TAPPI Press) FEED

MOTOR

ACCEPTS

-

LIGHTWEIGHT CONTAMINANTS

-

FIBERS

Figure 5. Gyrocleaner (Reproduced with permission from ref. 10. Copyright 1993 TAPPI Press)

In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

314

PLASTICS, RUBBER, AND PAPER RECYCLING

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

Stock Preparation. The cleaned fibers from the four processing systems are then sent to the stock preparation area of the paperboard machine and blended into three systems that supply the three layers of the forming process. The filler ply or middle layer process is shown in Figure 6. This process stream uses a blend of newspaper, boxshop, and OCC fibers to provide both product bulk and strength. Each of the fiber classes is refined separately. The refining process works the fibers in a high shear zone to increase swelling or rehydration. This improves the bonding potential of the fibers and resultant product strength and stiffness. The flexibility of the K - l Recycler process allows the refining processes to be optimized for each fiber source for improved strength while avoiding damage that weakens the fibers. After refining, the fibers are blended and diluted to about 0.75% solids and screened again in preparation for forming.

NEWS FROM PLANT6

i

DEFLAKING

BOX FROM PLANTS

OCC FROM PLANT6

DOUBLE DISC REFINING

DOUBLE DISC REFINING

BASIS WT. METERING

PRIMARY SCREENING

I

FILLER PLY

FILLER PLY

SECONDARY SCREENING

TERTIARY SCREENING

Figure 6. Filler Ply Stock System

The top liner and back liner stock systems are fed a single source offiber.The back liner is 100% news, and the top liner uses the light blend described in the fiber cleaning section. Process flow diagrams for both of these systems are shown in Figures 7 and 8. These systems also have refining capability and then dilute the fibers to about 0.2% solids in preparation for further cleaning. A series of centrifugal cleaners on both systems removes contaminants using a similar principle to the Gyrocleaners used at higher solids in the OCC fiber system. These cleaners use hydraulic flow to create the separation forces. The centrifugal force on a particle tending to move it outward is balanced by the drag and buoyant forces. A drawing of the principle of cleaner operation is shown in Figure 9.

In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

26. JANDA

Advances in Paper Fiber Recycling

315

TOP PLY

TOP BLEND FROM PLANT 6

DOUBLE DISC REFINING

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

BASIS WT METERING

PRIMARY CLEANING

PRIMARY SCREENING

SECONDARY CLEANING

SECONDARY SCREENING

TOP PLY

TERTIARY CLEANING

SEWER

Figure 7. Top Liner Process NEWS FROM PLANT 6

DOUBLE DISC REFINING

BASIS WT. METERING

BACK PLY

CURRENTLY IDLE

PRIMARY CLEANING

PRIMARY SCREENING REJ. ACC.

SECONDARY CLEANING

SECOr*DARY SCREEENING REJ.

TERTIARY CLEANING REJ.

SEWER

Figure 8. Back Liner Process

In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

BACK PLY

316

PLASTICS, RUBBER, AND PAPER RECYCLING

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

Centrifugal Force -4

Buoyancy Force M

Drag Force Figure 9. Cleaner Operation (Adapted from ref. 11.) A vortex flow pattern is created by the shape of the cleaner body, and the contaminants are separated from the fiber by differences in specific gravity (11). A table of typical contaminants and their specific gravity ranges is shown in Figure 10. The larger the difference in specific gravity from that of fiber and water, the easier it is to get a good separation.

Sand Metal Clay Wax Polyethylene Styrofoam Polystyrene Latex/Rubber Hot Melt Glues Pressure Glue Asphalt Ink

Specific Gravity 2.0-2.2 6.0-9.0 1.8-2.6 0.9-1.0 0.91-0.97 0.3-0.5 1.04-1.1 0.9-1.1 0.95-1.1 0.9-1.1 1.1-1.5 1.2-1.6

Separation by Density Difference Forward Cleaner - Remove Specific Gravity > 1 Reverse Cleaner - Remove Specific Gravity < 1 Figure 10. Contaminants Specific Gravity (Adapted from ref. 11.)

In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

26. JANDA

Advances in Paper Fiber Recycling

317

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

Contaminant Analysis. Chemical analysis of the contaminants that make it through the system is used to manage and improve the fiber cleaning process. The Analytical Chemistry Research Lab at the Neenah Technical Center provides analysis of composition and structure of these materials. Analytical methods used for paperboard and machine deposit samples are FT-IR spectrometer with a microscope to examine small contaminants, Mass Spectrometer with fast atom bombardment, and C-13 NMR. This information is used by process engineers to continue to improve product and process cleanliness by adjusting the process systems for better removal. Contaminant information allows the operators to look for offending materials in incoming materials. Fiber suppliers also can use the information to screen their sources. Forming System. Papermaking on the K - l Recycler begins with three fourdrinier forming systems that each produce a separate paper web. Unlike the cylinder type formers traditionally used in the production of recycled paperboard, the multiple former concept provides increased flexibility in how each fiber component is treated and used. Figure 11 is a schematic drawing of how the three layers are formed and then combined to get one multilayer web.

Figure 11. Multiple Layer Fourdrinier This increased flexibility provides the potential to engineer the paperboard product to use each recycled fiber class in the furnish to get maximum product performance. This capability is key to meeting the challenge of providing maximum product performance while using recycled fibers. The photo in Figure 12 shows the scale of the triple former unit. Retention aids and sizing to control moisture pickup are added to the dilute slurries from the top liner, filler ply, and back liner stock systems before forming. The amount of filler ply is adjusted to control the thickness and final basis weight of the product. The dilute slurries are pumped to their respective headboxes where they are distributed across the width of the moving drainage surface with a precision orifice called a slice. The velocity of the slurry exiting the slice is adjusted to nearly match that of the moving drainage fabric or wire. The relative orientation of the fibers is controlled by adjusting this velocity difference (12). This in turn effects the directional orientation of the physical properties in the paperboard produced.

In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

318

PLASTICS, RUBBER, AND PAPER RECYCLING

Figure 12. K - l Recycler Multiple Ply Former A key measure of paperboard performance in folding cartons is the resistance to bending called Taber stiffness (13). Britt states: "In many instances the basis weight (of the paperboard) is determined by the stiffness required, and means to increase stiffness would permit lower basis weight and saving of material" (14). Preserving and enhancing the stiffness of the paperboard is important to the efficient use of recycled fibers that tend to be weaker as a result of repeated recycling. The use of potentially weaker recycled fibers sometimes conflicts with the goal of packaging source reduction (packaging weight reduction). The K - l Recycler is designed to meet the challenge of both recycling and source reduction. While fibers in a paper web tend to lie parallel to the paper plane, the tendency of all machine-made papers to orient the fibers in the direction of the moving wire can be minimized, and the stiffness of the product in the weakest or cross machine direction can be maximized (15). Process trials on the forming section have shown the capability to control the ratio of machine direction to cross direction Taber stiffness from 3.5 to 1.8. The capability to make this adjustment is used to improve the paperboard stiffness in the cross machine direction. Since many applications of paperboard depend on the minimum strength or stiffness, this capability is key to producing a high performance paperboard while using a furnish of 100% recycled fibers that tend to be weakened by repetitive recycling. Each fourdrinier table has drainage elements consisting of vacuum boxes and foils that speed water removal from the web of fibers. The drainage table for each layer is specially adjusted to improve the formation of the class of recycled fiber on that table. Formation is a descriptive property of paper which includes the "degree of fiber dispersion, the extent and type of fiber orientation, and the degree of packing or solid fraction (16)." Kershaw states that the formation of a paper web can influence other sheet properties, such as sheet strength, appearance, and the

In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

26. JANDA

Advances in Paper Fiber Recycling

319

anisotropy or directional distribution of paper properties (17). Good formation is key to effective and efficient use of fiber materials, especially for meeting the challenge when using recycled fibers. The middle filler layer drainage system has a top wire system that allows twosided drainage. This insures a uniform distribution of fiber lengths and fines to each drainage surface. The similarity of the top and bottom sides of the middle layer insures that it will bond to both the top liner and back liner in the same way, producing a superior multilayer product. A schematic drawing of a top wire unit is shown in Figure 13.

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

Tamfornw Top ••watering Unit

Figure 13. Top Wire Former Each web is drained to about 9% solids. The separate top liner, middle filler layer, and back liner webs are then pressed or "couched" together to form one strong multilayer paperboard web. Paperboard Process. The multilayer web is then transported to the press section where multiple nips mechanically remove water from the web until it is about 50% solids. The damp web then passes through the dryer section where water is thermally removed resulting in a raw paperboard sheet at 96% solids. The raw web is calendered and treated to smooth the surface and prepare for the coating process. The top side is double coated to provide a smooth and white uniform surface for coating. The coating is a blend of clay and titanium dioxide in a synthetic binder. The coating make-up system is completely automated and controlled by the same distributed control system that controls the fiber preparation and papermaking systems. The two-step coating application consists of a base bar applied coat followed by an air knife application. The coating is then dried and the paperboard recalendered to achieve a glossy surface. It is then wound in large reels and slit and rewound to the customer's request. Product Applications. K - l PaceSetter® 100% recycled paperboard is used in a wide range of packaging and printing applications. These applications range from cereal boxes and other folding cartons to the backing for blister packaging and labels and tags.

In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

320

PLASTICS, RUBBER, AND PAPER RECYCLING

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

A cross-section microphotograph of the product at 125X magnification is shown in Figure 14. The two coating layers show up as light and dark layers. Unfortunately, this technique does not show the difference among the different fiber classes, fiber orientation, or multilayer construction.

Figure 14. 125 X microphotograph of Paperboard Cross Section Continued Advances. Improvements to the K - l Recycler process are being planned to continue meeting the challenge. Studies are under way to identify projects to improve the fiber preparation area to increase contaminant removal and improve fiber strength. Similar programs are also under way for the forming and coating section to insure K - l maintains its technology advantage. Comparison to Deinking Process James River Corporation is also meeting the recycling challenge with processes for recovering and deinking fiber for the production of high quality white office papers and towel and tissue products. James River's newest deinking recycling plant is the Halsey, Oregon, facility. The Halsey plant was started up in March of 1992 at a cost of $70 million. It processes about 400 metric tons of waste paper daily to produce about 275 metric tons of recycled pulp. A comparison of the K - l recycled paperboard process to the Halsey deinked pulp process provides insight into the specific challenges faced in each process. Fiber Sources. The Halsey Mill processes office paper waste including white and colored ledger grades and coated book papers. This material is collected and sorted from large sources and tends to be more homogeneous in fiber properties than the materials used in coated recycled paperboard. Fiber Cleaning and Bleaching. The Halsey waste paper is contaminated with materials associated with office or desk use, such as ink, fillers, paper clips, staples, glue, and dirt. The fiber cleaning process begins with similar repulping and screening systems to the K - l system. However, there is only one process stream, and the waste paper is blended together. A two-stage bleaching process using

In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

26.

JANDA

Advances in Paper Fiber Recycling

321

hydrogen peroxide and sodium hydrosulfite is used to remove color. This achieves high pulp whiteness and brightness without using chlorine.

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

Deinking. Ink is removed from the fibers using a foam flotation process. Air is injected into a diluted solution of thefibers,dispersed ink particles, and surfactant. The hydrophobic ink particles are adsorbed or trapped by the rising air bubbles and skimmed off the top. This process is effective in eliminating dark spots from pulp at a cost of increased waste water volume and increased fiber losses. The Halsey plant has an advanced water treatment system to handle this load. Products. The deinked pulp is then thickened and pressed to about 50% solids for use at the Halsey Tissue Mill and transported to the James River Camas, Washington, and Wauna, Oregon, mills. Final products are Eureka!™ copy paper, Renaissance™ commercial tissue and towel products, Quilted Northern® bath tissue, and Brawny® paper towels. Key Process Differences. The K - l and Halsey processes show the range of challenges in recycling paper fiber. The K - l fiber source is heterogeneous, representing several different fiber classes. These fiber classes are processed separately to achieve the highest performance. The contaminants found in the K - l system represent the different end uses and collection systems associated with these different fiber classes. The Halsey furnish is relatively homogeneous with predictable contaminants from offices and office collection systems. Fiber losses and treatment costs are much higher in a deinking and bleaching process. A deinking plant like Halsey tends to supply several paper machines and paper mills while the K - l fiber system is integrated with the single paperboard machine. The capital cost of the deinking process per ton of pulp produced is much greater than that of a recycled paperboard fiber system. Conclusion James River Corporation is meeting the challenge of increasing paper fiber recycling rates while maintaining and improving recycled product performance. Both the K - l process for producing PaceSetter® 100% recycled paperboard and the Halsey fiber deinking plant process represent the application of state-of-the-art technology in the processing and use of recycled fiber to meet a wide range of product needs. Acknowledgments I would like to thank my coworkers at James River's Neenah Technical Center and the Kalamazoo Paperboard Mill for their assistance in preparing this paper. Specific assistance was provided by: Dr. Kim Robinson - Recycledfibermechanics Dr. John Litvay - Microphotographs Mr. Mike Schmitt - K - l fiber cleaning Mr. Rex Robertson - K - l stock preparation and forming Mr. Robert De Jong - Halsey Fiber Plant Mrs. Pamala Tackman - Document preparation and editing Mr. Mike Henderson - Macintosh computer network support

In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.

322

PLASTICS, RUBBER, AND PAPER RECYCLING

Downloaded by UNIV OF SYDNEY on September 24, 2015 | http://pubs.acs.org Publication Date: May 5, 1995 | doi: 10.1021/bk-1995-0609.ch026

Literature Cited 1 Stilwell, E. J.; Canty, R. C.; Kopf, P. W.; and Montrone, A. M., Packaging For The Environment, (Author D. Little: 1991), p. 47. 2 Alexander, J. H., In Defense of Garbage. (Praeger Publishers: 1993) p. 24. 3 Paper Recovery Programs Continue to Grow, The Official Board Markets "The Yellow Sheet". March 19, 1994; (Advanstar Communications, Vol. 70, No. 12, Cleveland, OH), p. 1. 4 Alexander, J. H., p. 119 5 Bouchard, J., and Douek, M.; The Effects of Recycling on the Chemical Properties of Pulps. Journal of Pulp and Paper Science, Vol. 20, No. 5, May 1994, p. J136 6 Howard, R. C. ,and Bichard, W., The Basic Effects of Recycling on Pulp Properties. PAPRICAN Report PPR 864, May 1991, p. 4 7 Stilwell, E. J.;Canty, R. C.; Kopf, P. W.; and Montrone, A. M., p. 55 8 Zirngibl, P., RPTA Production-Technical Seminar, Proceedings May 1993, p. 11-2. 9 Bliss, T., Secondary Fiber Recycling: Spangenberg, R. J. ed., (TAPPI Press, 1993), p. 127 10 Ibid., p. 120 11 Ibid.; p. 103 12 Kershaw, T. N., Pulp and Paper. Chemistry and Chemical Technology, Casey, J. P. ed., 3rd Edition Vol. 2, (John Wiley & Sons, Inc.: 1980) p. 1027. 13 Brandon, C. E., Pulp and Paper. Chemistry and Chemical Technology, Casey, J. P. ed., 3rd Edition Vol. 3, (John Wiley & Sons, Inc.: 1980) p. 1810. 14 Britt, K. W., Handbook of Pulp and Paper Technology. Britt, K. W., ed., 2nd Edition, (Van Nostrand Reinhold Co., 1970) p. 677. 15 Kershaw, p. 1027 16 Kershaw, p. 965. 17 Ibid. RECEIVED June 20,

1995

In Plastics, Rubber, and Paper Recycling; Rader, C., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1995.