Rapid Analysis of Bisphenol A and Its Analogues ... - ACS Publications

Subscriber access provided by Mount Allison University | Libraries and Archives

Article

Rapid Analysis of Bisphenol A and Its Analogs in Food Packaging Products by Paper Spray Ionization Mass Spectrometry Shuo Chen, Quanying Chang, Kai Yin, Qunying He, Yongxiu Deng, Bo Chen, Chengbin Liu, Ying Wang, and Liping Wang J. Agric. Food Chem., Just Accepted Manuscript • Publication Date (Web): 24 May 2017 Downloaded from http://pubs.acs.org on May 25, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Journal of Agricultural and Food Chemistry is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 31

Journal of Agricultural and Food Chemistry

1

Rapid Analysis of Bisphenol A and Its Analogs in Food Packaging Products by Paper

2

Spray Ionization Mass Spectrometry

3 4

Shuo Chen,†,‡ Quanying Chang, § Kai Yin,† Qunying He,† Yongxiu Deng,† Bo Chen,‡,*

5

Chengbin Liu,† Ying Wang, §,* and Liping Wang#

6 7

†

8

and Chemical Engineering, Hunan University, Changsha 410082, China

9

‡

State Key Laboratory of Chemo/Biosensing and Chemometrics, College of Chemistry

Key Laboratory of Phytochemical R&D of Hunan Province and Key Laboratory of

10

Chemical Biology & Traditional Chinese Medicine Research, Ministry of Education, Hu-

11

nan Normal University, Changsha 410081, China

12

§

College of Finance and Statistics, Hunan University, Changsha 410082, China

13

#

Hunan Analysis and Testing Center, Changsha 410004, China

∗

Corresponding authors. E-mail address: [email protected]. Tel & Fax: +86-731-

88872531

1 ACS Paragon Plus Environment


14 15

Page 2 of 31

ABSTRACT In this study, a paper spray ionization mass spectrometric (PS-MS) method was de-

16

veloped for the rapid in situ screening and simultaneous quantitative analysis of bi-

17

sphenol A and its analogs, i.e., bisphenol S, bisphenol F, and bisphenol AF, in food pack-

18

aging products. At the optimal PS-MS conditions, the calibration curves of bisphenols in

19

the range of 1-100 µg/mL were linear. The correlation coefficients were higher than

20

0.998, the LODs of the target compounds were 0.1-0.3 µg/mL. After a simple treatment

21

by dichloromethane on the surface, the samples were analyzed by PS-MS in situ for rapid

22

screening without a traditional sample pretreatment procedure, such as powdering, ex-

23

traction and enrichment steps. The analytical time of the PS-MS method was less than 1

24

min. In comparison with conventional HPLC-MS/MS, it was demonstrated that PS-MS

25

was a more effective high-throughput screening and quantitative analysis method.

26 27

Keywords: bisphenol A, bisphenol S, bisphenol F, bisphenol AF, paper spray ionization

28

mass spectrometry, food packaging products.


Page 3 of 31

29


INTRODUCTION

30

Bisphenol A (Figure 1) is widely employed to produce polycarbonate plastics and

31

epoxy resins, which are used in many plastic food packaging products, including baby

32

bottles, drinking containers, and snack packaging.1-6 However, there are a number of

33

studies that confirm the considerable damage of bisphenol A on human health, including

34

neural disorders and behavioral dysfunction and reproductive damage etc.7-13 In 2015, a

35

document on risk assessment was published in the Food Contact Materials, Enzymes,

36

Flavourings and Processing Aids (CEF) Panel's “Scientific opinion on the risks to public

37

health related to the presence of bisphenol A in foodstuff”. The CEF Panel established a

38

temporary Tolerable Daily Intake (t-TDI) of 4 µg/kg bw/d by aplying a total uncertainty

39

factor of 150.14

40

In addition, bisphenol A analogs, such as bisphenol S, bisphenol F, and bisphenol

41

AF (Figure 1), have similar physicochemical properties to 1. Therefore, the analogs are

42

rendered as candidates for replacement 1 in industrial applications.9 Unfortunately, this

43

similarity is also expected to result in harmful toxicological profiles. Kitamura et al.15

44

demonstrated that 1 and 2 were potent anti-androgen compounds. Castro et al.16 found

45

potential adverse effects of 3 and 2 in the developing brain of mammals. Kinch et al.17

46

demonstrated that 1 and 2 induce precocious hypothalamic neurogenesis at low-dose ex-

47

posures. Additional harmful effects have been proven, including genotoxicity, DNA

48

damage,18 oxidative stress etc.19 In 2016, Chen et al.20 reviewed the environmental occur-

49

rence, human exposure and toxicity of bisphenol analogs other than 1. They showed that

50

2, 3 and 4 may drive a new global contamination trend as 1 replacements.



51

Because of their high sensitivity and selectivity, LC-MS and GC-MS are usually

52

used to identify 1 and its analogs.21-23 However, sample pretreatment methods, such as

53

liquid-liquid extraction,22 solid-phase extraction,23 or solid-phase micro extraction,24 for

54

complex samples, e.g., urine, require considerable time and labor, and the analytical

55

throughput of the methods is low. In addition, LC-MS is not easy to use for the rapid

56

screening of 1 and its analogs in food packaging products because the separation is time

57

consuming.

58

Page 4 of 31

Ambient mass spectrometry (AMS) is a new technology. It can directly analyze

59

sample or sample surface without or with less sample pretreatment. After Cooks’ group

60

presented desorption electrospray ionization (DESI),25 AMS has been developed rapidly

61

because of its rapid, high-throughput merits.26-28 It is a potential high-throughput screen-

62

ing method for hazardous ingredients. Now, more than 30 ambient ionization methods

63

have been developed.29 Among different AMS techniques, paper spray MS (PS-MS) has

64

unique advantages, e.g. in situ analysis and simple instrumental construction for ioniza-

65

tion. In addition, PS-MS has good quantitation ability (18 MΩ) used for the experiments was purified by a Milli-Q System.

89

The samples, including mineral water bottles, energy drink bottles, plastic cups, pa-

90

per cups and baby bottles,. were purchased from Wal-Mart (Changsha, China). One baby

91

bottle was an imported product produced by Philips Avent Corporation (UK).

92

Apparatus

93

A ZQ 2000 single-quad mass spectrometer with a scan speed range of 197 to 3980

94

Da/s (Manchester, UK) was used to record the signal for PS-MS analysis. The resolution

95

was as follows: the peaks at 1080.8 and 1081.8 from an infusion of β-cyclodextrin re-

96

solved with a valley between them of no more than 10% of the average height of the two



97

peaks. An XYZR (three-dimensional plus angle adjustment) moving platform was made

98

in-house and used to accurately control location of the spray tip.

Page 6 of 31

99

LC-MS/MS analysis was accomplished using an LCMS-8050 liquid chromatograph

100

mass spectrometer (Shimadzu, Kyoto, Japan) coupled with two LC-20AD HPLC pumps,

101

a SIL-20A autosampler, a DGU-20A3R degassing unit, and a CTO-20A column oven.

102

System control and data processing were performed with the Labsolutions chromatog-

103

raphy workstation, version 5.75 (Shimadzu).

104

Rapid Screening Analysis by Direct Sample Spray-MS

105

Samples were cut into triangle-like shapes with dimensions of 4 mm at the base and

106

10 mm in height for paper spray. Before direct sample spray-MS analysis, the plastic

107

piece was soaked in dichloromethane for 1 min. After being dried under nitrogen, the

108

sample was fixed on the XYZR moving platform by an alligator clamp; the triangular tip

109

was held 5 mm from the ion cone of the MS. Ten microliters of methanol was used as a

110

spray solvent and dropped on the sample surface, then -2.5 kV was applied to form the

111

sample spray ionization. The spray process lasted for 10-15 s. For paper product analysis,

112

the method was the same but without soaking in dichloromethane.

113

The MS parameters for the working negative ion mode of the ZQ 2000 for PS-MS

114

analysis were as follows: cone voltages: -40 V; extractor voltage: -1 V; ion energy: 0.5;

115

source temperature: 100 °C; RF lens voltage: -0.5 V; cone gas (N2): 5 L/h.

116

Rapid Quantitative Analysis by PS-MS

117

For rapid quantitative analysis by PS-MS, triangular filter paper (base: 6 mm;

118

height: 12 mm) was employed as PS substrates. The triangular paper was cut by a CUT-


Page 7 of 31


119

OK DC 330 craft cutting plotter (Hefei CNC Equipment Co., Hefei, China). The sample

120

volume for PS-MS analysis was 10 µL.

121

Bisphenol A-d16 was used as I. S. at 10 µg/mL in a series of standard solutions us-

122

ing methanol as solvent. The calibration curves of 1, 2, 3, and 4 were constructed with

123

ratios of abundance of target ions (m/z of 1, 2, 3, 4 was 227, 249, 199, 335, respectively)

124

to I.S. (m/z: 241) vs. the concentrations of 1, 2, 3, 4, respectively. The concentration

125

range was 1-100 µg/mL. The limits of detection (LOD) were determined by injecting di-

126

luted standards. The least concentrated standard yielding a signal/noise ratio >3 was con-

127

sidered as the LOD.

128

For polymer samples for analyses, the sample treatment method was similar to the

129

FDA method.41 The detailed procedures are as follows: 0.10 of cut sample was mixed

130

with 2 mL of methylene chloride in a flask. The flask was placed in an ultrasonic water

131

bath for 30 min to dissolve the sample. Eight milliliters of methanol was added in the

132

flask to precipitate the polymer completely. The polymer precipitate was allowed to settle

133

for 10 min. Five milliliters of the sample filter liquor was dried by N2 stream. The residue

134

was redissolved in 0.2 mL of methanol including 10 µg/mL of bisphenol A-d16.

135

For paper products, the sample, cut into small pieces, was extracted by shaking with

136

methanol. After filtering, 1 mL of the sample solution was dried by N2. The residual 1

137

and its analogs were redissolved in 1 mL of methanol including 10 µg/mL of bisphenol

138

A-d16.40

139

LC-MS/MS Analysis.



140

The samples were also analyzed by LC-MS/MS to investigate the accuracy of PS-

141

MS. The sample pretreatment methods were similar to those of the PS-MS analysis. LC-

142

MS/MS conditions were similar to those in the literature.22

143

Page 8 of 31

The column used was a 150 mm × 2.0 mm i.d., 5 µm, Shim-pack VP-ODS (Shimad-

144

zu). The mobile phase was methanol:water, with 0.1% ammonium hydroxide (v/v). A

145

gradient elution was adopted starting with 30% MeOH and reaching 90% MeOH in 3

146

min, maintaining this percentage for 2 min and finally to 30% MeOH and held for 4 min

147

prior to the next injection. The column temperature was kept at 50 °C. The mobile phase

148

flow-rate was set at 0.4 mL/min, and the injection volume was 10 µL. MS conditions

149

were as follows: MS scan range was m/z 100−500 using electrospray ionization (ESI)

150

working in negative ion mode. Interface, DL, and heat block temperatures were 300, 250,

151

and 400 °C, respectively. Nitrogen was used as a sheath gas, ion sweep gas and auxiliary

152

gas at flow rates of 40, 10 and 55 arbitrary units, respectively. Argon used as a collision-

153

induced dissociation (CID) gas was approximately 1.5 mTorr, the collision energy was

154

3.5 V. The deprotonated molecule [M-H]- was used as the precursor ion. Quantitation

155

was made in MRM mode. The following channels were utilized: 227>211 for 1; 249>108

156

for 2; 241>223 for bisphenol A-d16; 199>93 for 3 and 335>265 for 4. All collision ener-

157

gies (CE) were 25 V.

158

RESULTS AND DISCUSSION

159

Optimization of PS-MS Conditions

160

To study the effect of different solvents on the PS-MS response, different solvents,

161

i.e., water, methanol (MeOH), ethanol (EtOH), ethyl ether (EtOAc), benzene and their

162

mixtures, were investigated using 1 as a model target on a filter paper matrix. Ten micro-


Page 9 of 31


163

liters of 1 standard solution in methanol (10 µg/mL) was dropped on triangular filter pa-

164

per. After being dried by N2, spray solvent was dropped on the paper, and voltage was

165

then applied to finish PS-MS. The results showed that the MS signal of 1 was too low

166

when ethyl ether and water were used as solvents, and the result with benzene as the sol-

167

vent was lower than methanol and ethanol. Methanol was the best solvent for PS-MS

168

analysis of 1. The responses in all mixed solvents were lower than that in methanol.

169

The selection of spray volume plays an important part in PS-MS detection. The ef-

170

fect of different spray volumes of methanol, i.e., 5, 10, 15 and 20 µL, on the MS signal of

171

1 at the same concentration (10 µg/mL) was investigated at a -2.5 kV spray voltage using

172

filter paper as the matrix. The results showed that the response intensity of 1 was mini-

173

mized when the spray volume was 5 µL. When the spray volume was 10 µL, the response

174

intensity was good, but when it was 15 µL, the response started to drop off. At 20 µL, the

175

response was close to the minimum. When the volume was too small (5 µL), the for-

176

mation of stable Taylor cone jets are difficult. However, a larger volume will form multi-

177

ple Taylor cone jets, reducing the sensitivity.30 Ten milliliters of spray volume was se-

178

lected for subsequent experiments.

179

The spray voltage of PS-MS must be chosen carefully in the negative ion mode. Op-

180

timization of the spray voltage for the detection of bisphenols was completed. The effects

181

of different spray voltages on PS-MS responses showed that -2.5 kV was optimal for the

182

detection of bisphenols. When the voltage was low, ionization efficiency was limited. A

183

higher voltage will also affect the sensitivity because the onset voltage of electrical dis-

184

charge is always lower than that of electrospray ionization, seriously degrading ESI per-

185

formance.



Page 10 of 31

186

Because the temperature of the MS source of ZQ 2000 also affects the sensitivity

187

due to the formation of solvent adduct ion and its effect on ion transmission, different

188

source temperatures, i.e., 50 °C, 70 °C, 85 °C, 100 °C, 120 °C, 150 °C, were investigated.

189

The results demonstrated that 100 °C gave the best PS-MS response at [M-H]- of 1. Be-

190

cause there was a small spray solvent volume, a higher source temperature was adverse

191

during ion transmission due to thermal degradation. In addition, ion transmission effi-

192

ciency will also be reduced when the temperature is low. Therefore, 100 °C was selected

193

for subsequent experiments.

194

Pretreatment of the Plastic Surface for in situ PS-MS Analysis for Rapid Screening

195

For in situ PS-MS analysis, different sample matrixes, such as plastic and paper

196

products, significantly affected the sensitivity. For paper products, such as paper cups,

197

bisphenols in the thin coating can be easily extracted by methanol and spray ionization.

198

However, plastic was difficult to analyze by PS-MS only using methanol as the spray

199

solvent. Its surface was smooth (Figure 2A) and methanol cannot effectively extract bi-

200

sphenols from the matrix. To effectively analyze plastic products in situ by PS-MS, we

201

used dichloromethane to destroy the smooth surface and extract bisphenols to the surface.

202

The SEM images of untreated and treated surfaces of a baby bottle containing 1 are pre-

203

sented in Figure 2, which shows that the surface rugosity is completely different. After

204

treatment, the specific surface area increased dramatically. In addition, bisphenols can

205

also be extracted to the surface, increasing the detection sensitivity. To further optimize

206

the experimental conditions, in situ PS-MS responses of 1 were compared over different

207

treatment times, such as 30 s, 1 min, 3 min, 5 min, 10 min. The results showed that the

208

response of 1 min treatment was the highest. With increased treatment time, the response


Page 11 of 31


209

decreased. With 5 min of treatment, the response reduced substantially, and at 10 min

210

there was no PS-MS response. When treated with dichloromethane, there are two proce-

211

dures: 1. The smooth surface is destroyed and more 1 is exposed on the surface; and 2. 1

212

on the surface diffuses into the solvent. Competition between the two procedures affects

213

the amount of 1 on the surface. When the treatment time was long, almost all the 1 on the

214

surface diffused into the solvent. Therefore, there was no PS-MS response.

215

Quantitative Analysis by PS-MS

216

A typical PS-MS mass spectra of mixed standards is shown in Figure 3. The calibra-

217

tion curves of bisphenols are shown in Figure 4. The chromatograms of standards at dif-

218

ferent concentrations and I.S. are shown in Figure 5.

219

In the range of 1-100 µg/mL for 1, 2, 3, and 4, the correlation coefficients are greater

220

than 0.998. The limits of detection (LODs) were 0.1, 0.1, 0.3, 0.1 µg/mL for 1, 2, 3, 4,

221

respectively. Using baby bottle extract without bisphenols as the matrix, the LODs were

222

almost same with that of the diluted standards, i.e., 0.1, 0.2 0.3 0.2 µg/mL for 1, 2, 3, 4,

223

respectively. The comparison of typical samples analyzed by PS-MS and HPLC-MS/MS

224

are given in Table 1.

225

The quantitative results of PS-MS are similar to those of HPLC-MS/MS, suggesting

226

that PS-MS quantitative analysis is useful for the rapid determination of bisphenols in

227

food packaging products. However, the repeatability by PS-MS (RSD: 8.4%), especially

228

for plastic products, is lower than that of HPLC-MS/MS (RSD: 3.5%). Nonvolatile plas-

229

tic matrix effects may be a major factor affecting effective ionization. Therefore, more

230

effective sample pretreatment is necessary for accurate quantitation by PS-MS.

231

Application of PS-MS for the Analysis of Bisphenols



232

Forty-two samples were analyzed after in situ rapid screening and then quantitated

233

by PS-MS. The results are listed in Table 2. A typical PS-MS spectrum of a sample is

234

shown in Figure 6.

235

Page 12 of 31

The results demonstrate that 1 are still major chemical contaminants in food packag-

236

ing products, including paper products and plastic products. 2 likewise appeared in prod-

237

ucts. 3 and 4 were not been detected.

238

The increasing awareness regarding safety to bisphenol A and its analogs requires

239

methods capable of handling numerous samples in a short time frame. From the results

240

obtained in this study, the PS-MS method presented is capable of rapidly screening for 1,

241

3, 2 and 4 at a rate of approximately 1 min/sample. Moreover, it has been demonstrated

242

that quantitation of bisphenols in food packaging products by PS-MS using deuterated

243

internal standards is feasible. The results of sample analyses showed that the food pack-

244

aging products still use 1 in raw material in China, and as a replacement for 1, 2 has en-

245

tered the market in China.

246 247

ABBREVIATIONS

248

PS-MS, paper spray ionization mass spectrometric; BPA, bisphenol A; BPS, bisphenol S;

249

BPF, bisphenol F; BPAF, bisphenol AF; EFSA, European Food Safety Authority; CEF,

250

Food Contact Materials, Enzymes, Flavourings and Processing Aids; t-TDI, temporary

251

Tolerable Daily Intake; AMS, ambient mass spectrometry; DESI, desorption electrospray

252

ionization; DCBI, desorption corona beam ionization.

253 254

SUPPORTING INFORMATION*


Page 13 of 31


255

Figure SI-1. Picture of the XYZR moving platfor

256

Figure SI-2. PS-MS response of 1 with different spray solvent

257

Figure SI-3. PS-MS response in different spray volume

258

Figure SI-4. PS-MS response at different spray voltage

259

Figure SI-5. PS-MS response of 1 at different source temperatures

260

Figure SI-6. In-situ PS-MS response of 1 with different treating times

261 262 263

*This material is available free of charge via the internet at http://pubs.acs.org.

264

AUTHOR INFORMATION

265 266

Alternate corresponding author:

267

*: Ying Wang. Address: College of Finance and Statistics, Hunan University, Changsha

268

410082, China. Tel & Fax: +86-731-88822286. E-mail: [email protected]

269 270

ACKNOWLEDGMENTS The authors would like to thank local health inspection institute for samples collec-

271 272

tion.

273 274 275

CONFLICT OF INTEREST The authors declare no competing financial interest.

276 277

FUNDING



278

Page 14 of 31

The authors thank the National Natural Science Foundation of China (21575040,

279

71673078, 21275049) and the construction program of the key discipline of Hunan Prov-

280

ince for financial support. The project was also supported by the foundation for innova-

281

tive research groups of the Hunan Natural Science Foundation of China (2015JC1001).


Page 15 of 31


282

REFERENCES

283

1.

Vandenberg, L. N.; Chahoud, I.; Heindel, J. J.; Padmanabhan, V.; Paumgartten, F. J.;

284

Schoenfelder, G. Urinary, circulating, and tissue biomonitoring studies indicate

285

widespread exposure to bisphenol A. Ciência & Saúde Coletiva 2012, 17, 407–434.

286

2.

2006, 226, 79–89.

287 288

Kang, J. H.; Kondo, F.; Katayama, Y. Human exposure to bisphenol A. Toxicology

3.

Rocha, B. A.; Azevedo, L. F.; Gallimberti, M.; Campiglia, A. D.; Barbosa, F. High

289

levels of bisphenol A and bisphenol S in Brazilian thermal paper receipts and estima-

290

tion of daily exposure. J. Toxicol. Environ. Health, Part A 2015, 78, 1181–1188.

291

4.

Yang, Y.; Guan, J.; Yin, J.; Shao, B.; Li, H. Urinary levels of bisphenol analogues in

292

residents living near a manufacturing plant in South China. Chemosphere 2014, 112,

293

481–486.

294

5.

Staples, C. A.; Dome, P. B.; Klecka, G. M.; Oblock, S. T.; Harris, L. R. A review of

295

the environmental fate, effects, and exposures of bisphenol A. Chemosphere 1998,

296

36, 2149–2173.

297

6.

ruary 2017).

298 299

7.

Chen, M. Y.; Ike, M.; Fujita, M. Acute toxicity, mutagenicity, and estrogenicity of bisphenol-A and other bisphenols. Environ. Toxicol. 2002, 17, 80–86.

300 301

About bisphenol A. http://www.bisphenol-a.org/about/index.html (accessed: 11 Feb-

8.

Richter, C. A.; Birnbaum, L. S.; Farabollini, F.; Newbold, R. R.; Rubin, B. S.;

302

Talsness, C. E.; Vandenbergh, J. G.; Walser-Kuntz, D. R.; vom Saal, F. S. In vivo ef-

303

fects of bisphenol A in laboratory rodent studies. Reprod. Toxicol. 2007, 24, 199–

304

224.



305

9.

Zhang, X.; Chang, H.; Wiseman, S.; He, Y.; Higley, E.; Jones, P.; Wong, C. K.; Al-

306

Khedhairy, A.; Giesy, J. P.; Hecker, M. Bisphenol A disrupts steroidogenesis in hu-

307

man H295R cells. Toxicol. Sci. 2011, 121, 320–327.

308

10. Ulutas, O. K.; Yildiz, N.; Durmaz, E.; Ahbab, M. A.; Barlas, N.; Cok, I. An in vivo

309

assessment of the genotoxic potential of bisphenol A and 4-tert-octylphenol in rats.

310

Arch. Toxicol. 2011, 85, 995–1001.

311

Page 16 of 31

11. Yeo, M.; Patisaul, H.; Liedtke, W. Decoding the language of epigenetics during neu-

312

ral development is key for understanding development as well as developmental neu-

313

rotoxicity. Epigenetics 2013, 8, 1128–1132.

314

12. Li, D.; Zhou, Z.; Qing, D.; He, Y.; Wu, T.; Miao, M.; Wang, J.; Weng, X.; Ferber, J.

315

R.; Herrinton, L. J.; Zhu, Q.; Gao, E.; Checkoway, H.; Yuan, W. Occupational expo-

316

sure to bisphenol-A (BPA) and the risk of self-reported male sexual dysfunction.

317

Hum. Reprod. 2010, 25, 519–527.

318

13. Khalil, N.; Ebert, J. R.; Wang, L.; Belcher, S.; Lee, M.; Czerwinski, S. A.; Kannan,

319

K. Bisphenol A and cardiometabolic risk factors in obese children. Sci. Total

320

Environ. 2014, 470–471, 726–732.

321

14. Scientific Opinion on the risks to public health related to the presence of bisphenol A

322

(BPA) in foodstuffs. http://www.efsa.europa.eu/en/efsajournal/pub/3978 (accessed:

323

18 March 2017).

324

15. Kitamura, S.; Suzuki, T.; Sanoh, S.; Kohta, R.; Jinno, N.; Sugihara, K.; Yoshihara, S.;

325

Fujimoto, N.; Watanabe, H.; Ohta, S. Comparative study of the endocrine-disrupting

326

activity of bisphenol A and 19 related compounds. Toxicol. Sci. 2005, 84, 249–259.

327

16. Castro, B.; Sánchez, P.; Torres, J. M.; Ortega, E. Bisphenol A, bisphenol F and bi-


Page 17 of 31


328

sphenol S affect differently 5α-reductase expression and dopamine–serotonin sys-

329

tems in the prefrontal cortex of juvenile female rats. Environ. Res. 2015, 142, 281–

330

287.

331

17. Kinch, C. D.; Ibhazehiebo, K.; Jeong, J. H.; Habibi, H. R.; Kurrasch, D. M. Low-

332

dose exposure to bisphenol A and replacement bisphenol S induces precocious hypo-

333

thalamic neurogenesis in embryonic zebrafish. Proc. Natl. Acad. Sci. U. S. A. 2015,

334

112, 1475–1480.

335

18. Rosenmai, A. K.; Dybdahl, M.; Pedersen, M.; Alice van Vugt-Lussenburg, B. M.;

336

Wedebye, E. B.; Taxvig, C.; Vinggaard, A. M. Are structural analogues to bisphenol

337

A safe alternatives? Toxicol. Sci. 2014, 139, 35–47.

338

19. Michalowicz, J.; Mokra, K.; Bak, A. Bisphenol A and its analogs induce morpholog-

339

ical and biochemical alterations in human peripheral blood mononuclear cells (in

340

vitro study). Toxicol. In Vitro 2015, 29, 1464–1472.

341

20. Chen, D.; Kannan, K.; Tan, H.; Zheng, Z.; Feng, Y. L.; Wu, Y.; Widelka, M. Bi-

342

sphenol analogues other than BPA: environmental occurrence, human exposure, and

343

toxicity—a review. Environ. Sci. Technol. 2016, 50, 5438–5453.

344

21. Wilczewska, K.; Namiesnik, J.; Wasik, A. Troubleshooting of the determination of

345

bisphenol A at ultra-trace levels by liquid chromatography and tandem mass spec-

346

trometry. Anal. Bioanal. Chem. 2016, 408, 1009–1013.

347

22. Rocha, B. A.; da Costa, B. R.; de Albuquerque, N. C.; de Oliveira, A. R.; Souza, J.

348

M.; Al-Tameemi, M.; Campiglia, A. D.; Barbosa, F., Jr. A fast method for bisphenol

349

A and six analogues (S, F, Z, P, AF, AP) determination in urine samples based on dis-

350

persive liquid-liquid microextraction and liquid chromatography-tandem mass spec-



351 352

Page 18 of 31

trometry. Talanta 2016, 154, 511–519. 23. Schmidt, L.; Muller, J.; Goen, T. Simultaneous monitoring of seven phenolic me-

353

tabolites of endocrine disrupting compounds (EDC) in human urine using gas chro-

354

matography with tandem mass spectrometry. Anal. Bioanal. Chem. 2013, 405, 2019–

355

2029.

356

24. Tan, F.; Zhao, H.; Li, X.; Quan, X.; Chen, J.; Xiang, X.; Zhang, X. Preparation and

357

evaluation of molecularly imprinted solid-phase microextraction fibers for selective

358

extraction of bisphenol A in complex samples. J. Chromatogr. A 2009, 1216, 5647–

359

5654.

360

25. Takáts, Z.; Wiseman, J. M.; Gologan, B.; Cooks, R. G. Mass spectrometry sampling

361

under ambient conditions with desorption electrospray ionization. Science 2004, 306,

362

471–473.

363 364 365 366 367 368

26. Cooks, R. G.; Ouyang, Z.; Takats, Z.; Wiseman, J. M. Ambient mass spectrometry. Science 2006, 311, 1566–1570. 27. Venter, A.; Nefliu, M.; Cooks, R. G. Ambient desorption ionization mass spectrometry. TrAC, Trends Anal. Chem. 2008, 27, 284–290. 28. Harris, G. A.; Galhena, A. S.; Fernández, F. M. Ambient sampling/ionization mass spectrometry: applications and current trends. Anal. Chem. 2011, 83, 4508–4538.

369

29. Monge, M. E.; Harris, G. A.; Dwivedi, P.; Fernández, F. M. Mass spectrometry: re-

370

cent advances in direct open air surface sampling/ionization. Chem. Rev. 2013, 113,

371

2269–2308.

372 373

30. Lin, C. H.; Liao, W. C.; Chen, H. K.; Kuo, T. Y. Paper spray-MS for bioanalysis. Bioanalysis 2014, 6, 199–208.


Page 19 of 31


374

31. Wang, H.; Liu, J.; Cooks, R. G.; Ouyang, Z. Paper spray for direct analysis of com-

375

plex mixtures using mass spectrometry. Angew. Chem., Int. Ed. 2010, 49, 877–880.

376

32. Hajslova, J.; Cajka, T.; Vaclavik, L. Challenging applications offered by direct analy-

377

sis in real time (DART) in food-quality and safety analysis. TrAC, Trends Anal.

378

Chem. 2011, 30, 204–218.

379

33. Bentayeb, K.; Ackerman, L. K.; Begley, T. H. Ambient ionization–accurate mass

380

spectrometry (AMI-AMS) for the identification of nonvisible set-off in food-contact

381

materials. J. Agric. Food Chem. 2012, 60, 1914–1920.

382

34. Wang, Y. J.; Li, X.; Sun, W. J.; Mu, H.; Zhang, X. Q.; Ma, H. Y.; Xu, T. T.; Gao, C.

383

Rapid analysis of bisphenol A in food packaging materials by desorption corona

384

beam ionization tandem mass spectrometry. Chinese J. Anal. Chem. 2014, 42, 88–92.

385

35. Shen, Y.; van Beek, T. A.; Claassen, F. W.; Zuilhof, H.; Chen, B.; Nielen, M. W. Rap-

386

id control of Chinese star anise fruits and teas for neurotoxic anisatin by Direct

387

Analysis in Real Time high resolution mass spectrometry. J. Chromatogr. A 2012,

388

1259, 179–186.

389 390 391

36. Pomilio, A. B.; Bernatene, E. A.; Vitale, A. Desorption electrospray ionization ambient mass spectrometry. Acta Bioquim. Clin. Latinoam. 2011, 45, 47–79. 37. García-Reyes, J. F.; Jackson, A. U.; Molina-Díaz, A.; Cooks, R. G. Desorption elec-

392

trospray ionization mass spectrometry for trace analysis of agrochemicals in food.

393

Anal. Chem. 2009, 81, 820–829.

394

38. Ballesteros-Gomez, A.; Jonkers, T.; Covaci, A.; de Boer, J. Screening of additives in

395

plastics with high resolution time-of-flight mass spectrometry and different ioniza-

396

tion sources: direct probe injection (DIP)-APCI, LC-APCI, and LC-ion booster ESI.



397 398

Page 20 of 31

Anal. Bioanal. Chem. 2016, 408, 2945–2953. 39. Ma, Q.; Bai, H.; Li, W.; Wang, C.; Li, X.; Cooks, R. G.; Ouyang, Z. Direct identifi-

399

cation of prohibited substances in cosmetics and foodstuffs using ambient ionization

400

on a miniature mass spectrometry system. Anal. Chim. Acta 2016, 912, 65–73.

401

40. Liao, C.; Liu, F.; Kannan, K. Bisphenol S, a new bisphenol analogue, in paper prod-

402

ucts and currency bills and its association with bisphenol A residues. Environ. Sci.

403

Technol. 2012, 46, 6515–6522.

404

41. Biles, J. E.; McNeal, T. P.; Begley, T. H.; Hollifield, H. C. Determination of bi-

405

sphenol-A in reusable polycarbonate food-contact plastics and migration to food-

406

simulating liquids. J. Agric. Food Chem. 1997, 45, 3541–3544.


Page 21 of 31


407

FIGURE CAPTIONS

408

Figure 1. Chemical structures of bisphenol A and analogues.

409

(M1=228.29, M2=250.27, M3=200.24, M4=336.23)

410

Figure 2. SEM images of sample surface. (A) Sample without treatment, (B) Sample

411

treated for 1 min

412

Figure 3. PS-MS spectra of 1 and its analogues (10 µg/mL)

413

m/z: 3, 199; 1, 227; bisphenol A-d16, 241; 2, 249; 4, 335

414

Figure 4. Calibration curves of 1, 2, 3, 4 in the range of 1-100 µg/mL using bisphenol A-

415

d16 as I.S.

416

Figure 5. Chromatogram of 1, 2, 3, 4 and bisphenol A-d16 by PS-MS

417

Figure 6. PS-MS spectra of baby bottle with bisphenol A-d16



Page 22 of 31

Table 1. Comparison Results Between PS-MS and HPLC-MS/MS PS-MS (mg/kg) (n=5)

HPLC-MS/MS (mg/kg) (n=5)

sample 1

2

1

2

Paper cup

12.2±0.7

ND

11.8±0.3

ND*

Baby bottle 1

ND

7.9±0.3

ND

8.5±0.2

Baby bottle 2

34.6±2.5

ND

36.2±1.3

ND

food packaging paper

67.2±5.7

ND

69.9±2.4

ND

food packaging film

32.3±1.7

ND

33.7±0.9

ND

*ND: Not detected.


Page 23 of 31


Table 2. Sample Analysis Results by PS-MS PS-MS quantitative results (n=5) (µg/g) sample 1

2

1

2

1

PC 1

positive

negative

12.2±0.7

ND

2

PC 2

positive

negative

22.7±1.2

ND

3

PC 3

positive

negative

14.5±0.9

ND

4

PC 4

positive

negative

18.7±1.2

ND

5

PC 5

positive

negative

25.6±1.4

ND

6

PlC 1

positive

negative

20.6±1.3

ND

7

PlC 2

positive

negative

42.7±3.0

ND

8

PlC 3

positive

negative

27.8±1.3

ND

9

PlC 4

positive

negative

32.2±0.9

ND

10

BB 1

negative

positive

ND

7.9±0.3

11

BB 2

positive

negative

34.6±2.5

ND

12

BB 3

negative

negative

ND

ND

13

BB 4

positive

negative

30.1±3.0

ND

14

MWB 1

positive

negative

67.2±5.7

ND

15

MWB 2

positive

negative

43.4±3.9

ND

16

MWB 3

positive

negative

35.1±1.9

ND

17

MWB 4

positive

negative

10.3±0.7

ND

18

EDB 1

positive

negative

22.2±1.3

ND

19

EDB 2

positive

negative

10.7±1.0

ND

20

EDB 3

positive

negative

34.1±1.6

ND

21

EDB 4

positive

negative

9.2±0.8

ND

22

FPF 1

positive

negative

32.3±1.7

ND

23

FPF 2

positive

negative

34.7±2.9

ND



Page 24 of 31

24

FPF 3

positive

negative

18.9±1.1

ND

25

FPF 4

positive

negative

24.3±1.1

ND

26

FPF 5

positive

negative

13.2±0.9

ND

27

IPC 1

positive

negative

42.7±2.7

ND

28

IPC 2

positive

negative

40.3±2.9

ND

29

IPC 3

positive

negative

35.1±1.4

ND

30

IPC 4

positive

negative

37.9±2.1

ND

31

IPC 5

positive

negative

46.8±2.7

ND

32

IPC 6

positive

negative

27.3±2.0

ND

33

FPP 1

positive

negative

67.2±5.7

ND

34

FPP 2

positive

negative

43.4±3.9

ND

35

FPP 3

positive

negative

46.1±2.7

ND

36

FPP 4

positive

negative

27.5±1.8

ND

37

FPP 5

positive

negative

38.1±2.7

ND

38

FPP 6

positive

negative

21.4±1.5

ND

39

FPP 7

positive

negative

17.8±1.5

ND

40

DS 1

positive

negative

51.9±3.7

ND

41

DS 2

positive

negative

45.2±2.6

ND

42

DS 3

positive

negative

47.8±3.2

ND


Page 25 of 31


O S O HO

OH

HO

OH 2. Bisphenol S

1. Bisphenol A

F

HO

OH

F

FFF

HO

3. Bisphenol F

F

OH

4. Bisphenol AF Figure 1.



Page 26 of 31

Figure 2.


Page 27 of 31


Figure 3.



1

Page 28 of 31

3

2

4

Figure 4.


Page 29 of 31


Figure 5



Page 30 of 31

Figure 6


Page 31 of 31


ToC 254x190mm (96 x 96 DPI)

ACS Paragon Plus Environment

Rapid Analysis of Bisphenol A and Its Analogues ... - ACS Publications

Recommend Documents