Strain Hardening and Pore Size Harmonization by Uniaxial

Jun 30, 2017 - ... and affords free-standing hydrogels that can be converted to highly ... and nematic ordering bear great potential for other applica...
0 downloads 0 Views 3MB Size
Article

Strain hardening and pore size harmonization by uniaxial densification: A facile approach towards superinsulating aerogels from nematic nanofibrillated 2,3-dicarboxyl cellulose Sven F. Plappert, Jean-Marie Nedelec, Harald Rennhofer, Helga C. Lichtenegger, and Falk W. Liebner Chem. Mater., Just Accepted Manuscript • DOI: 10.1021/acs.chemmater.7b00787 • Publication Date (Web): 30 Jun 2017 Downloaded from http://pubs.acs.org on June 30, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Chemistry of Materials is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 22

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Chemistry of Materials

Strain hardening and pore size harmonization by uniaxial densification: A facile approach towards superinsulating aerogels from nematic nanofibrillated 2,3dicarboxyl cellulose Sven F. Plappert†, Jean-Marie Nedelec‡, Harald Rennhofer§, Helga C. Lichtenegger§, Falk W. Liebner†* †



Division of Chemistry of Renewable Resources, University of Natural Resources and Life Sciences Vienna, Konrad-Lorenz-Straße 24, 3430 Tulln, Austria

Université Clermont Auvergne, CNRS, SIGMA Clermont, ICCF, F-63000 Clermont-Ferrand, France §

Institute of Physics and Material Sciences, University of Natural Resources and Life Sciences Vienna, Peter-Jordan-Straße 82, 1190 Vienna, Austria *corresponding author: [email protected]

ABSTRACT Dissolving pulp has been subjected to consecutive periodate / chlorite treatments to afford 2,3-dicarboxyl cellulose (DCC, 1.02 mmol g-1 COOH). Subsequent nanofibrillation afforded stable nematic nf-DCC dispersions (average particle size 2.1 nm x 525 nm) at significantly lower energy input compared to TEMPO-oxidation. Acidinduced gelation triggered by extensive hydrogen bonding sets the ordered state and affords free-standing hydrogels that can be converted to highly transparent birefringent aerogels by scCO2 drying. Uniaxial compression of the obtained ultra-lightweight ductile nf-DCC aerogels down to 5 % of their original volume intriguingly preserves nematic orientation and transparence. Simultaneously, strain hardening translates into exceptionally good mechanical properties, such as toughness at nearly zero Poisson’s ratio. Uniaxial compression has been furthermore demonstrated to be a facile and efficient means for converting nf-DCC aerogels of broad, multi-scale pore size distribution into entirely micro/mesoporous scaffolds of narrow size distribution at farreaching preservation of porosity. Following this approach, thermally super-insulating nf-DCC aerogels (λ = 0.018 W m-1 K-1) have been prepared whose intriguing mechanical properties, transparence and nematic ordering bear great potential for other applications as well.

ACS Paragon Plus Environment

Chemistry of Materials

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

INTRODUCTION Self-assembly and liquid-crystalline ordering of nano-scale cellulose fibers promoted by charged surfaces moieties is an intriguing approach towards nano-structured bio-based materials. Surface charges are capable of increasing the effective volume of such anisometric nanoparticles promoting their self-assembly into liquid crystal phases as first described by Onsager 1. This phenomenon has so far been used in the preparation of liquid crystal templates 2, 3, photonic materials 4, 5, nanocomposites 6 and transparent aerogels 7. Cellulose aerogels of narrow pore size distribution in the mesopores range (< 50 nm diameter) are potential super-insulating materials as heat conduction via the gas phase as the main transport mechanisms of heat in organic aerogels is largely hindered due to the Knudsen effect 8. Predominantly silica-based aerogels have been hitherto explored as thermal super-insulating materials (λ ≥ 14 mW m-1 K-1) 9 since their porosity in terms of size and narrow distribution can be easily controlled in the required range by sol-gel chemistry. Recently, both synthetic and natural polymer based aerogels have increasingly moved into the focus of thermal insulation, such as polyurethanes (e.g., polyurethane aerogels from BASF; λ ≥ 19.8 mW m-1 K-1) 10 or pectin (e.g., Aeropectin; λ ≥ 20 mW m-1 K-1) 11. Different from silica, cellulose-based aerogels whose synthesis does not follow the principles of the classic Teichner sol-gel chemistry exhibit rather wide pore-size distributions and consist of voids whose diameters frequently distinctly exceed 100 nm rendering them less suited for insulation applications. Therefore a variety of recent studies have investigated templating approaches that combine morphological features of inorganic and entirely mesoporous nanostructured materials with the particular properties of cellulose 8, 12-15. Nanocellulose is particularly useful in this respect as it imparts the composite materials strength and flexibility, and can simultaneously compensate the brittleness inherent to most inorganic aerogels 13, 14. Kobayashi et al. 7 recently presented an approach towards thermal superinsulating cellulosic aerogels that circumvents the use of templating inorganic constituents. It is based on acidinduced gelation of low-concentrated aqueous dispersions of cellulose nanofibrils obtained by TEMPO-oxidation (2,2,6,6-tetramethylpiperidinyloxyl) of pulp and subsequent mechanical nanofibrillation (TOCN). Conversion of the obtained hydrogels into aerogels employing supercritical carbon dioxide drying (scCO2) afforded a novel type of lightweight aerogels which was reported to feature thermal super-insulation properties for a certain density window owing to the presence of highly ordered, narrow-mashed TOCN networks and the low heat conduction of the solid phase 7. Although respective aerogels contain a certain volume fraction of mesopores, the size of the voids accounting for most of the pore volume is not in the desired range (diameter 50-100 nm). Beyond that, the low bulk densities of these TOCN aerogels owing to the poor castability of dispersions having a TOCN content significantly greater than 20 mg cm-3 results in somewhat tough but rather poor mechanical properties. Therefore, this study investigates and proposes uniaxial compression as a means of poresize control and strain-hardening to obtain entirely mesoporous, fully biopolymer-based and mechanical strong nanocellulose aerogels aiming at super-insulating properties. Furthermore it investigated in how far key features, such as nematic ordering, specific surface area, birefringence and transparency – rather elusive for other cellulose-based aerogels or porous materials – can be preserved throughout uniaxial compression, as this would be of great benefit to a broad variety of applications no matter whether 3D materials (aerogels: thermal ACS Paragon Plus Environment

Page 2 of 22

Page 3 of 22

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Chemistry of Materials

superinsulation, sensing, matrices for optical devices, e.g.) or 2D materials (membranes: filtration, fractionation of nanoparticles, sensing, e.g.) are considered 16. While the above cited work on TOCN aerogels is based on heterogeneous TEMPO-mediated oxidation affording 6-carboxyl cellulose, we followed a different approach relying on sequential periodate and chlorite oxidation as chemical pulp pretreatments. Unlike TEMPOoxidation, periodate regio-selectively converts the vicinal secondary hydroxyl groups in C2 and C3 position of the anhydroglucose units (AGU) into aldehyde groups which are subsequently further oxidized by chlorite to carboxyl moieties, hence affording 2,3-dicarboxyl cellulose (DCC). As periodate oxidation occurs under cleavage of the pyran ring (between C2 and C3), conformational freedom is supposedly added to that introduced by creation of negative charges alongside the cellulose chains which is not the case for TEMPO-mediated oxidation. Thereby, it was expected that nanofibrillation of DCC could afford smaller particles compared to TOCN and would require less energy. The good recyclability of sodium periodate by simple ozone treatment 17 along with the fact that neither the preparation of 3D materials like aerogels nor self-alignment of nanofibrillated 2,3-dicarboxyl cellulose (nf-DCC) in aqueous dispersion have been hitherto reported were further motifs of this study. To the best of our knowledge, DCC nanofibrils have been hitherto only investigated for the preparation of 2D materials for packaging, oxygen barrier 18 and filtration 19 applications.

EXPERIMENTAL SECTION Materials. Never-dried, sulfite dissolving pulp (fagus spp., TCF bleached, CCOA 24.3 µmol g-1 C=O, FDAM 13.9 µmol g-1 COOH, Mw 303.7 kg mol-1, 50 %w) was used as cellulosic starting material. Sodium periodate, acetic acid, sodium chlorite was purchased at the highest grade available and used without further purification. Preparation of 2,3-dialdehyde cellulose (DAC). 24 g dissolving pulp (50 %w) was disintegrated in 1 L of deionized water using a conventional kitchen blender for one minute. Then 200 mL of 0.23 M NaIO4 was added and the reaction mixture was stirred at 600 rpm and 50°C for three hours. Oxidation was stopped by filtering-off the formed 2,3-dialdehyde cellulose from the aqueous oxidant solution followed by immediate thorough washing of DAC with deionized water. Storage of the never-dried DAC until further processing (within 3 days) was accomplished at 4 °C and a solid content of 5.5 %w. Determination of aldehyde content. The degree of oxidation of DAC was determined according to the method by Sirviö at al. 20 relying on quantitative oximation of the carbonyl moieties and subsequent determination of the nitrogen content by elemental analysis (Carlo Erba EA 1108 CHNS-O instrument). Preparation of nanofibrillated 2,3-dicarboxyl cellulose (nf-DCC). 2 g of DAC was dispersed in 200 mL 1 M acetic acid. After addition of 2.013 g NaClO2 the reaction mixture was stirred (600 rpm) at 20°C for 16.5 hours. Oxidation was stopped by filtering-off the formed 2,3-dicarboxyl cellulose (DCC) from the aqueous oxidant solution followed by immediate and exhaustive washing of DCC with deionized water. Nanofibrillation of DCC was accomplished by repeated homogenization (2 times at 50 MPa then 2 times at 80 MPa) of aqueous 0.25 %w dispersions of DCC which had been adjusted to pH 7.5 by addition of 0.1 M NaOH. After fibrillation the dispersion was centrifuged at 5000 rpm (∼ 4830 g) for one hour to remove possible non-fibrillated residues. The obtained nf-DCC dispersion was subsequently concentrated to ≥1 %w using a vacuum rotavapor. ACS Paragon Plus Environment

Chemistry of Materials

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Determination of carboxyl content. The amount of carboxyl groups on nf-DCC was determined by conductometric titration. In brief 100 mg of freeze dried DCC nanofibrils were disintegrated in 50 mL of distilled water. After adding 2.75 mL of 0.1 M hydrochloric acid and continued stirring (30 min), the equilibrium H+ concentration was measured (pH 2.75). Conductometric titration of the dispersion was then started and maintained under continued stirring until a total of 5 mL aqueous 0.1 M NaOH at an increment of 25 µL every 30 seconds had been added. An automated titration apparatus consisting of a 800 Dosino dosing device connected to an 856 conductivity module (Metrohm, Switzerland) was used. Atomic force microscopy (AFM) of nf-DCC. AFM scans were made from diluted nf-DCC dispersions dried on mica discs using a Dimension Icon Scanning Probe Microscope (Bruker AXS, France; formerly Veeco) equipped with OTESPA cantilever operated in tapping mode and a NanoScope V control station. Gwyddion 2.40 software was employed for image processing. Preparation of nf-DCC aerogels. Aqueous dispersions of nf-DCC (≥1 %w/v) were poured into molds of various size and geometry. Acid-induced gelation was accomplished by immersing the molds in aqueous 1 M HCl for 1 hour per 1 cm mold depth. The gels were then transferred into aqueous 50% ethanol and finally to absolute ethanol with four solvent exchanges every 24 hours. The resulting anhydrous alcogels were subjected to an ethanol extraction using supercritical CO2 (“scCO2 drying”; 9.5 MPa, 40 °C, flow rate of 40 g min-1, 23 hours). Drying was stopped by isothermal depressurization at a rate of 50 nm) and preservation of a minimum density (low λsolid) is hence an effective approach to reduce heat conductivity. This has been confirmed for the densified nf-DCC aerogels as exemplarily demonstrated for an nf-DCC ACS Paragon Plus Environment

Page 17 of 22

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Chemistry of Materials

aerogel of ultra-low density (23 mg cm-3). Uniaxial compression to 20% of its original height (ρB = 87 mg cm-3) affords a mechanically robust material that has a lower thermal conductivity than air (17.7 vs. 26 mW m-1 K-1 51 at 25 °C and ambient pressure). Nondensified nematically ordered aerogels prepared from nanofibrillated TEMPO-oxidized cellulose have been reported to feature similarly low thermal conductivities 7. However the latter exhibit these properties at very low density (17 mg cm-3) only, coinciding with rather weak mechanical properties. Also, compared with other biopolymer-based superinsulating aerogels, such as aeropectin 11 or even mesoporous silica aerogels 52, 53, uniaxially compressed nf-DCC aerogels are regarded superior due to their exceptionally good mechanical properties, ductility, transparence and nematically ordered particulate network morphology which invite to be exploited in traditional and novel applications.

Figure 8: Thermal conductivity (λ, 25°C) of nf-DCC aerogels of different initial densities after uniaxial compression to 20 % of their initial heights

CONCLUSION The presented approach comprising A) periodate oxidation of dissolving pulp to obtain DAC, B) conversion of DAC to DCC by chlorite oxidation, C) nanofibrillation of DCC in aqueous dispersion to afford self-aligning nf-DCC and D) acid-induced gelation of highly diluted nf-DCC dispersions gives access to transparent, nematic hydrogels. Replacement of water by ethanol followed by scCO2 drying of the anhydrous alcogels affords ultra-lightweigth, transparent and birefringent nf-DCC aerogels at otherwise preserved nematic orientation and solid network features. Compared to TEMPO oxidation and subsequent nanofibrillation which is hitherto the only alternative to afford carboxyl cellulose aerogels of comparable transparence, the two-step nf-DCC approach is superior for various reasons, including the lower size of the nanofibrils accessible already at lower energy input or the good recyclability of the oxidizing agent. Uniaxial densification has been tested to be a facile technique to impart nf-DCC aerogels mechanical properties inviting for real-world cellulose aerogel applications as in addition to strain-hardening the porosity and specific surface of the aerogels can be largely preserved even at 90% compression. Since uniaxial densification simultaneously harmonizes the multi-scale pore-size distributions typical of cellulosic aerogels in favor of mesopores and at the expense of macropores, the presented approach affords materials of ultralow thermal conductivity due to the largely suppressed heat conductivity through the gas phase (Knudsen effect). The preservation of nematic ordering

ACS Paragon Plus Environment

Chemistry of Materials

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

perpendicular to the compression axis, the alignment of mesopores as evident from the distinct capillary condensation of nitrogen at a specific relative pressure, and the compression-dependent transparency amplify the application potential of DCC aerogels and encourage for further studies.

ACKNOWLEDGEMENTS The financial support by the Austrian Science Fund (FWF: I848-N17) and the French Agence Nationale de la Recherche (ANR-11-IS08-0002; Austrian-French Project CAP-Bone) as well as the Austrian Federal Ministry for Agriculture, Forestry, Environment and Water Management (BMLFUW) through the WoodWisdom Net+ project AeroWood is gratefully acknowledged. Johannes Konnerth is gratefully acknowledged for his support on mechanical testing of the materials, as is Tiina Nypelö for performing AFM analysis of nf-DCC (Institute of Wood Technology and Renewable Materials, Department of Material Sciences and Process Engineering, University of Natural Resources and Life Sciences Vienna, Austria).

SUPPORTING INFORMATION The supporting information contains the detailed procedure applied to prepare TEMPOoxidized cellulose nanofibrils (TOCN) and a comparison between TOCN and nf-DCC with regard to fibril dimensions (AFM) and degree of oxidation (conductometric titration). Furthermore a visualization of the mechanical data concerning strain hardening of nf-DCC aerogels upon uniaxial densification is given.

REFERENCES 1. Onsager, L., The Effects of Shape on the Interaction of Colloidal Particles. Annals of the New York Academy of Sciences 1949, 51, 627-659. 2. Giese, M.; Blusch, L. K.; Khan, M. K.; MacLachlan, M. J., Functional Materials from CelluloseDerived Liquid-Crystal Templates. Angewandte Chemie 2014, 126, 9026 –9030. 3. Shopsowitz, K. E.; Kelly, J. A.; Hamad, W. Y.; MacLachlan, M. J., Biopolymer Templated Glass with a Twist: Controlling the Chirality, Porosity, and Photonic Properties of Silica with Cellulose Nanocrystals. Advanced Functional Materials 2014, 24, 327-338. 4. Kelly, J. A.; Shukaliak, A. M.; Cheung, C. C.; Shopsowitz, K. E.; Hamad, W. Y.; MacLachlan, M. J., Responsive photonic hydrogels based on nanocrystalline cellulose. Angewandte Chemie 2013, 52, 8912-6. 5. Giese, M.; Blusch, L. K.; Khan, M. K.; Hamad, W. Y.; MacLachlan, M. J., Responsive mesoporous photonic cellulose films by supramolecular cotemplating. Angewandte Chemie 2014, 53, 8880-4. 6. Habibi, Y.; Lucia, L. A.; Rojas, O. J., Cellulose nanocrystals: chemistry, self-assembly, and applications. Chemical reviews 2010, 110, 3479-500. 7. Kobayashi, Y.; Saito, T.; Isogai, A., Aerogels with 3D Ordered Nanofiber Skeletons of LiquidCrystalline Nanocellulose Derivatives as Tough and Transparent Insulators. Angewandte Chemie 2014, 53, 10394-7. 8. Baillis, D.; Coquard, R.; Moura, L. M., Heat transfer in cellulose-based aerogels: Analytical modelling and measurements. Energy 2015, 84, 732-744.

ACS Paragon Plus Environment

Page 18 of 22

Page 19 of 22

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Chemistry of Materials

9. Ko, E. I., AEROGELS. In Kirk-Othmer Encyclopedia of Chemical Technology, 5. ed.; Seidel, A., Ed. John Wiley & Sons, Inc.: Hoboken, New Jersey, 2004-2007; Vol. 1, pp 748-769. 10. Fricke, M.; Elbing, M. Process for producing aerogels or xerogels. 2012. 11. Rudaz, C.; Courson, R.; Bonnet, L.; Calas-Etienne, S.; Sallee, H.; Budtova, T., Aeropectin: fully biomass-based mechanically strong and thermal superinsulating aerogel. Biomacromolecules 2014, 15, 2188-95. 12. Bendahou, D.; Bendahou, A.; Seantier, B.; Grohens, Y.; Kaddami, H., Nano-fibrillated cellulose-zeolites based new hybrid composites aerogels with super thermal insulating properties. Industrial Crops and Products 2015, 65, 374-382. 13. Zhao, S. Y.; Zhang, Z.; Sebe, G.; Wu, R.; Virtudazo, R. V. R.; Tingaut, P.; Koebel, M. M., Multiscale Assembly of Superinsulating Silica Aerogels Within Silylated Nanocellulosic Scaffolds: Improved Mechanical Properties Promoted by Nanoscale Chemical Compatibilization. Advanced Functional Materials 2015, 25, 2326-2334. 14. Cai, J.; Liu, S.; Feng, J.; Kimura, S.; Wada, M.; Kuga, S.; Zhang, L., Cellulose-silica nanocomposite aerogels by in situ formation of silica in cellulose gel. Angewandte Chemie 2012, 51, 2076-9. 15. Demilecamps, A.; Beauger, C.; Hildenbrand, C.; Rigacci, A.; Budtova, T., Cellulose–silica aerogels. Carbohydrate Polymers 2015, 122, 293-300. 16. Toivonen, M. S.; Kaskela, A.; Rojas, O. J.; Kauppinen, E. I.; Ikkala, O., Ambient-Dried Cellulose Nanofibril Aerogel Membranes with High Tensile Strength and Their Use for Aerosol Collection and Templates for Transparent, Flexible Devices. Advanced Functional Materials 2015, 25, 6618-6626. 17. Koprivica, S.; Siller, M.; Hosoya, T.; Roggenstein, W.; Rosenau, T.; Potthast, A., Regeneration of Aqueous Periodate Solutions by Ozone Treatment: A Sustainable Approach for Dialdehyde Cellulose Production. ChemSusChem 2016, 9, 825-33. 18. Sirvio, J. A.; Kolehmainen, A.; Visanko, M.; Liimatainen, H.; Niinimaki, J.; Hormi, O. E., Strong, self-standing oxygen barrier films from nanocelluloses modified with regioselective oxidative treatments. ACS applied materials & interfaces 2014, 6, 14384-90. 19. Visanko, M.; Liimatainen, H.; Sirvio, J. A.; Haapala, A.; Sliz, R.; Niinimaki, J.; Hormi, O., Porous thin film barrier layers from 2,3-dicarboxylic acid cellulose nanofibrils for membrane structures. Carbohydr Polym 2014, 102, 584-9. 20. Sirvio, J.; Hyvakko, U.; Liimatainen, H.; Niinimaki, J.; Hormi, O., Periodate oxidation of cellulose at elevated temperatures using metal salts as cellulose activators. Carbohydrate Polymers 2011, 83, 1293-1297. 21. Sørensen, B. E., A revised Michel-Lévy interference colour chart based on first-principles calculations. European Journal of Mineralogy 2013, 25, 5-10. 22. Jeong, Y.; Friggeri, A.; Akiba, I.; Masunaga, H.; Sakurai, K.; Sakurai, S.; Okamoto, S.; Inoue, K.; Shinkai, S., Small-angle X-ray scattering from a dual-component organogel to exhibit a charge transfer interaction. Journal of colloid and interface science 2005, 283, 113-22. 23. Pfeifer, P.; Ehrburger-Dolle, F.; Rieker, T. P.; Gonzalez, M. T.; Hoffman, W. P.; Molina-Sabio, M.; Rodriguez-Reinoso, F.; Schmidt, P. W.; Voss, D. J., Nearly space-filling fractal networks of carbon nanopores. Phys Rev Lett 2002, 88, 115502. 24. Glatter, O.; Kratky, H. C., Small Angle X-Ray Scattering. Academic Press: London, 1982. 25. Mehling, H.; Hautzinger, G.; Nilsson, O.; Fricke, J.; Hofmann, R.; Hahn, O., Thermal Diffusivity of Semitransparent Materials Determined by the Laser-Flash Method Applying a New Analytical Model. International Journal of Thermophysics 1998, 19, 941-949. 26. Kim, U.-J.; Kuga, S., Thermal decomposition of dialdehyde cellulose and its nitrogencontaining derivatives. Thermochimica Acta 2001, 369, 79-85. 27. Isogai, A.; Saito, T.; Fukuzumi, H., TEMPO-oxidized cellulose nanofibers. Nanoscale 2011, 3, 71-85. 28. Liimatainen, H.; Visanko, M.; Sirvio, J. A.; Hormi, O. E.; Niinimaki, J., Enhancement of the nanofibrillation of wood cellulose through sequential periodate-chlorite oxidation. Biomacromolecules 2012, 13, 1592-7.

ACS Paragon Plus Environment

Chemistry of Materials

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

29. Siller, M.; Amer, H.; Bacher, M.; Roggenstein, W.; Rosenau, T.; Potthast, A., Effects of periodate oxidation on cellulose polymorphs. Cellulose 2015, 22, 2245-2261. 30. Kim, U.-J.; Kuga, S.; Wada, M.; Okano, T.; Kondo, T., Periodate Oxidation of Crystalline Cellulose. Biomacromolecules 2000, 1, 488-492. 31. Kristiansen, K. A.; Potthast, A.; Christensen, B. E., Periodate oxidation of polysaccharides for modification of chemical and physical properties. Carbohydrate research 2010, 345, 1264-71. 32. van de Ven, T. G.; Sheikhi, A., Hairy cellulose nanocrystalloids: a novel class of nanocellulose. Nanoscale 2016, 8, 15101-14. 33. Paakko, M.; Ankerfors, M.; Kosonen, H.; Nykanen, A.; Ahola, S.; Osterberg, M.; Ruokolainen, J.; Laine, J.; Larsson, P. T.; Ikkala, O.; Lindstrom, T., Enzymatic hydrolysis combined with mechanical shearing and high-pressure homogenization for nanoscale cellulose fibrils and strong gels. Biomacromolecules 2007, 8, 1934-41. 34. Henriksson, M.; Henriksson, G.; Berglund, L. A.; Lindström, T., An environmentally friendly method for enzyme-assisted preparation of microfibrillated cellulose (MFC) nanofibers. European Polymer Journal 2007, 43, 3434-3441. 35. Fukuzumi, H.; Saito, T.; Isogai, A., Influence of TEMPO-oxidized cellulose nanofibril length on film properties. Carbohydrate Polymers 2013, 93, 172-7. 36. Scheirs, J.; Camino, G.; Tumiatti, W., Overview of water evolution during the thermal degradation of cellulose. European Polymer Journal 2001, 37, 933-942. 37. Tang, M. M.; Bacon, R., Carbonization of cellulose fibers—I. Low temperature pyrolysis. Carbon 1964, 2, 211-220. 38. Robbie, K.; Broer, D. J.; Brett, M. J., Chiral nematic order in liquid crystals imposed by an engineered inorganic nanostructure. Nature 1999, 399, 764-766. 39. Shopsowitz, K. E.; Qi, H.; Hamad, W. Y.; Maclachlan, M. J., Free-standing mesoporous silica films with tunable chiral nematic structures. Nature 2010, 468, 422-5. 40. Sescousse, R.; Gavillon, R.; Budtova, T., Aerocellulose from cellulose–ionic liquid solutions: Preparation, properties and comparison with cellulose–NaOH and cellulose–NMMO routes. Carbohydrate Polymers 2011, 83, 1766-1774. 41. Pircher, N.; Carbajal, L.; Schimper, C.; Bacher, M.; Rennhofer, H.; Nedelec, J.-M.; Lichtenegger, H. C.; Rosenau, T.; Liebner, F., Impact of selected solvent systems on the pore and solid structure of cellulose aerogels. Cellulose 2016, 23, 1949-1966. 42. Rivas Murillo, J. S.; Bachlechner, M. E.; Campo, F. A.; Barbero, E. J., Structure and mechanical properties of silica aerogels and xerogels modeled by molecular dynamics simulation. Journal of NonCrystalline Solids 2010, 356, 1325-1331. 43. Woignier, T.; Reynes, J.; Hafidi Alaoui, A.; Beurroies, I.; Phalippou, J., Different kinds of structure in aerogels: relationships with the mechanical properties. Journal of Non-Crystalline Solids 1998, 241, 45-52. 44. Woignier, T.; Pelous, J.; Phalippou, J.; Vacher, R.; Courtens, E., Elastic properties of silica aerogels. Journal of Non-Crystalline Solids 1987, 95-96, 1197-1202. 45. Rege, A.; Schestakow, M.; Karadagli, I.; Ratke, L.; Itskov, M., Micro-mechanical modelling of cellulose aerogels from molten salt hydrates. Soft Matter 2016, 12, 7079-88. 46. Jiang, F.; Hsieh, Y. L., Cellulose Nanofibril Aerogels: Synergistic Improvement of Hydrophobicity, Strength, and Thermal Stability via Cross-Linking with Diisocyanate. ACS applied materials & interfaces 2017, 9, 2825-2834. 47. Thommes, M.; Kaneko, K.; Neimark, A. V.; Olivier, J. P.; Rodriguez-Reinoso, F.; Rouquerol, J.; Sing, K. S. W., Physisorption of gases, with special reference to the evaluation of surface area and pore size distribution (IUPAC Technical Report). Pure and Applied Chemistry 2015, 87, 1051–1069. 48. Reichenauer, G.; Scherer, G. W., Effects upon Nitrogen Sorption Analysis in Aerogels. Journal of colloid and interface science 2001, 236, 385-386. 49. Scherer, G. W.; Smith, D. M.; Stein, D., Deformation of aerogels during characterization. Journal of Non-Crystalline Solids 1995, 186, 309-315. 50. Pitchumani, R.; Li, W.; Coppens, M.-O., Tuning of nanostructured SBA-15 silica using phosphoric acid. Catalysis Today 2005, 105, 618-622. ACS Paragon Plus Environment

Page 20 of 22

Page 21 of 22

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Chemistry of Materials

51. Weast, R. C., Handbook of Chemistry and Physics. The Chemical Rubber Co.: Cleveland (USA), 1967. 52. Pierre, A. C.; Pajonk, G. M., Chemistry of Aerogels and Their Applications. Chemical reviews 2002, 102, 4243-4266. 53. Hüsing, N.; Schubert, U., Aerogels—Airy Materials: Chemistry, Structure, and Properties. Angewandte Chemie International Edition 1998, 37, 22-45.

ACS Paragon Plus Environment

Chemistry of Materials

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Table of Contents / Abstract Graphic

ACS Paragon Plus Environment

Page 22 of 22