Summarization and Evaluation. 3. Ethers, Ketones, Aldehydes

saturation (Pref ) Psat), the liquid density of the substances over a temperature and pressure range. ... density, F(T,P)/F(T,Pref ) 0.1 MPa or Psat),...
4 downloads 0 Views 316KB Size
2

J. Chem. Eng. Data 1997, 42, 2-26

Reviews P-G-T Data of Liquids: Summarization and Evaluation. 3. Ethers, Ketones, Aldehydes, Carboxylic Acids, and Esters Ivan Cibulka,*,† Lubomı´r Hneˇ dkovsky´ ,† and Toshiharu Takagi‡ Department of Physical Chemistry, Institute of Chemical Technology, 166 28 Prague, Czech Republic, and Kyoto Institute of Technology, Kyoto 606, Japan

The published experimental P-F-T data for 21 ethers, 10 ketones, 9 aldehydes, 9 carboxylic acids, and 25 esters (74 substances) in the liquid phase are summarized and reviewed, and the parameters of the Tait equation are given for 73 substances considered. This equation allows the calculation of smoothed values of either the volume ratio, V(P)/V(Pref), and related properties (relative density, F(P)/F(Pref), compression, {1 - V(P)/V(Pref)}) or, using density data at atmospheric pressure (Pref ) 0.1 MPa) or at saturation (Pref ) Psat), the liquid density of the substances over a temperature and pressure range.

Introduction This work is a continuation of a compilation and critical evaluation of published P-F-T data of organic substances in a liquid state. The data for two groups of substances, 1-alkanols (part 1) and n-alkanes (part 2), have been already reviewed and evaluated ([94-cib/zik], [96-cib/hne]). With these classes of substances, the density data at atmospheric pressure, F(T,Pref ) 0.1 MPa), or at saturation, F(T,Pref ) Psat), had been critically evaluated [93-cib]. In this work the published experimental values of relative density, F(T,P)/F(T,Pref ) 0.1 MPa or Psat), were compiled from the literature and evaluated using the Tait equation. Sources of Data The original experimental data (5703 data points) processed were extracted from the database employed previously for 1-alkanols and n-alkanes to which some data obtained from the database installed at Kyoto Institute of Technology have been appended. A list of substances is presented in Table 1 along with Chemical Abstracts Registry Numbers (CASRN, supplied by the authors) and summary formulas. The characteristics of data that were available in the database for density and related quantities (molar and specific volumes, volume or density ratios, compression) of selected members of several classes of C,H,O compounds are summarized in Table 2. The temperature ranges and numbers of experimental values are restricted up to the critical temperature; i.e., only subcritical liquid density data were taken from the source database. A significantly lower number of direct experimental data sets, compared to 1-alkanols and n-alkanes, was found in the literature. Therefore also values (denoted by a letter F in the “data type” column of Table 2) calculated from smoothing functions presented in the papers (mostly the Tait equation), following as much as possible the information concerning the distribution of experimental points given by authors, were included for some substances if no direct experimental (D) or smoothed values (S) were available in the papers. * Fax: +42-2-2431-0273. E-mail: [email protected]. † Institute of Chemical Technology. ‡ Kyoto Institute of Technology.

S0021-9568(96)00199-9 CCC: $14.00

There are some data sets ([73-erm/bai], [75-gus/abd], [76gus/sad], [77-abd/gus], [77-gus/sad], [78-gus/asl], [78-gus/ asl-1], [79-bas/erm]) referenced in the journals of the former Soviet Union as being deposited in VINITI; due to difficulties in obtaining them these deposited data were not included in the evaluation. Treatment of Data and Method of Data Evaluation The procedures of treatment of data and the critical evaluation were essentially the same as those employed for 1-alkanols and n-alkanes, and the details may be found in our previous paper [94-cib/zik]. A brief summarization only is given below. Available data on the compressed-liquid density and related quantities were fitted by a Tait equation with temperature dependent parameters C(T) and B(T) written in the form

F(T,Pref(T))

[

F(T,P,c b,b B) )

1 - C(T,c b) ln

B(T,b B) + P

]

(1)

B(T,b B) + Pref(T)

where NC

C(T,c b) )

∑ c [(T - T )/100]

i

i

0

i)0

b c ) {ci} ) {c0, ..., cNC} (2) NB

B(T,b B) )

∑ b [(T - T )/100]

i

i

0

i)0

B b ) {bi} ) {b0, ..., bNB} (3) and T0 is a parameter with a preselected fixed value for which C(T0) ) c0 and B(T0) ) b0 hold. The reference values, F{T,Pref(T)} and Pref(T), were selected in the same way as previously; i.e., at temperatures below the normal boiling temperature the densities at atmospheric pressure (Pref ) 0.101 325 MPa) were used, while for higher temperatures the values along the saturation curve, i.e., saturated liquid densities and saturated vapor pressures, were employed. Experimental values of densities at atmospheric pressure or at saturation for the same sample reported along with © 1997 American Chemical Society

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997 3 Table 1. List of Substances: Names (Alternative Names), Chemical Abstracts Registry Numbers, CASRN (Supplied by the Authors), and Summary Formulas name (alternative name) Ethers 3-oxapentane (diethyl ether) 4-oxaheptane (di-n-propyl ether) 2,4-dimethyl-3-oxapentane (diisopropyl ether) 5-oxanonane (di-n-butyl ether) 6-oxaundecane (di-n-pentyl ether) 8-oxapentadecane (di-n-heptyl ether) 3,3-dimethyl-2-oxabutane (methyl tert-butyl ether) 4,4-dimethyl-3-oxapentane (ethyl tert-butyl ether) 3,3-dimethyl-2-oxapentane (methyl tert-pentyl ether) 2,5-dioxahexane (ethylene glycol dimethyl ether) 2,5,8-trioxanonane (diethylene glycol dimethyl ether) 4,7,10-trioxatridecane (diethylene glycol dipropyl ether) 2,5,8,11,14-pentaoxapentadecane (tetraethylene glycol dimethyl ether) 4-oxa-1,6-heptadiene (diallyl ether) methoxybenzene (methyl phenyl ether) tetrahydrofuran (oxolane) 1,3-dioxolane tetrahydropyran (oxane) 1,4-dioxane furan dibenzofuran

CASRN

formula

60-29-7 111-43-3 108-20-3 142-96-1 693-65-2 629-64-1 1634-04-4 637-92-3 994-05-8 110-71-4 111-96-6 72072-32-3 143-24-8 557-40-4 100-66-3 109-99-9 646-06-0 142-68-7 123-91-1 110-00-9 132-64-9

C4H10O C6H14O C6H14O C8H18O C10H22O C14H30O C5H12O C6H14O C6H14O C4H10O2 C6H14O3 C10H22O3 C10H22O5 C6H10O C7H8O C4H8O C3H6O2 C5H10O C4H8O2 C4H4O C12H8O

Ketones 2-propanone (dimethyl ketone) 2-butanone (methyl ethyl ketone) 2-pentanone (methyl n-propyl ketone) 3-pentanone (diethyl ketone) 2-hexanone (methyl n-butyl ketone) 4-methyl-2-pentanone (methyl isobutyl ketone) 4-heptanone (di-n-propyl ketone) 2-octanone (methyl n-hexyl ketone) cyclopentanone cyclohexanone

67-64-1 78-93-3 107-87-9 96-22-0 591-78-6 108-10-1 123-19-3 111-13-7 120-92-3 108-94-1

C3H6O C4H8O C5H10O C5H10O C6H12O C6H12O C7H14O C8H16O C5H8O C6H10O

75-07-0 123-38-6 123-72-8 78-84-2 110-62-3 590-86-3 111-71-7 124-13-0 100-52-7

C2H4O C3H6O C4H8O C4H8O C5H10O C5H10O C7H14O C8H16O C7H6O

64-18-6 64-19-7 79-09-4 79-31-2 124-07-2 334-48-5 143-07-7 544-63-8 57-10-3

CH2O2 C2H4O2 C3H6O2 C4H8O2 C8H16O2 C10H20O2 C12H24O2 C14H28O2 C16H32O2

79-20-9 141-78-6 108-21-4 102-76-1 106-36-5 105-68-0 106-70-7 101452-99-7 621-70-5 61597-96-4 6382-06-5 93-58-3 5444-75-7 119-36-8 2050-08-0 6259-76-3 80-62-6 2696-43-7 112-62-9 597-55-7

C3H6O2 C4H8O2 C5H10O2 C9H14O6 C6H12O2 C8H16O2 C7H14O2 C15H30O2 C21H38O6 C7H14O3 C8H16O3 C8H8O2 C15H22O2 C8H8O3 C12H16O3 C13H18O3 C5H8O2 C13H24O2 C19H36O2 C21H24O4

Aldehydes ethanal (acetaldehyde) propanal (propionaldehyde) butanal (butyraldehyde) 2-methylpropanal (isobutyraldehyde) pentanal (valeraldehyde) 3-methylbutanal (isovaleraldehyde) heptanal (enanthaldehyde) octanal (caprylic aldehyde) benzaldehyde Acids methanoic acid (formic acid) ethanoic acid (acetic acid) propanoic acid (propionic acid) 2-methylpropanoic acid (isobutyric acid) octanoic acid (caprylic acid) decanoic acid (capric acid) dodecanoic acid (lauric acid) tetradecanoic acid (myristic acid) hexadecanoic acid (palmitic acid) Esters methyl ethanoate (methyl acetate) ethyl ethanoate (ethyl acetate) 1-methylethyl ethanoate (isopropyl acetate) 1,2,3-propanetriyl triethanoate (glyceryl triacetate; triacetin) propyl propanoate (n-propyl propionate) 3-methylbutyl propanoate (isopentyl propionate) methyl hexanoate (methyl caproate) nonyl hexanoate (n-nonyl caproate) 1,2,3-propanetriyl trihexanoate (glyceryl trihexanoate, tricaproin) 2-methylpropyl 2-hydroxypropanoate (isobutyl lactate) pentyl 2-hydroxypropanoate (n-pentyl lactate) methyl benzenecarboxylate (methyl benzoate) 2-ethylhexyl benzenecarboxylate (2-ethylhexyl benzoate) methyl 2-hydroxybenzenecarboxylate (methyl salicylate) pentyl 2-hydroxybenzenecarboxylate (n-pentyl salicylate) hexyl 2-hydroxybenzenecarboxylate (n-hexyl salicylate) methyl 2-methyl-2-propenoate (methyl methacrylate) nonyl 2-methyl-2-propenoate (n-nonyl methacrylate) methyl (Z)-9-octadecenoate (methyl oleate) diethyl 2,2-bis(phenylmethyl)propane-1,3-dioate (diethyl dibenzylmalonate)

4

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997

Table 1 (Continued) name (alternative name)

CASRN

formula

diethyl butane-1,4-dioate (diethyl succinate) dipropyl butane-1,4-dioate (di-n-propyl succinate) dinonyl butane-1,4-dioate (di-n-nonyl succinate) dibutyl benzene-1,2-dicarboxylate (di-n-butyl phthalate) 4-methyl-1,3-dioxolan-2-one (propylene carbonate)

123-25-1 925-15-5 15805-77-3 84-74-2 108-32-7

C8H14O4 C10H18O4 C22H42O4 C16H22O4 C4H6O3

compressed-liquid density data were preferably used for the reference density, F(T,Pref), and thus the values of relative density, F(T,P)/F(T,Pref ) 0.1 MPa or Psat), reported by the authors were correlated by eq 1. If the reference values were not available in the original source, then densities obtained from the equations summarized in Appendix I were employed in the correlations. In those few cases where the correlations were performed in the temperature region above the normal boiling temperature (i.e., where either both the reference density values F(T,Pref ) Psat) and the compressed-liquid density data or relative quantities at temperatures above the normal boiling point were available), saturated vapor pressures were calculated from the smoothing functions taken from the literature (see Appendix I) and used in the correlations. Reference densities, F(T,Pref) reported in the papers are presented in the form of smoothing functions of temperature in Appendix II. Adjustable parameters b c and b b of function 1 were obtained by minimizing the objective function Np

φ(c b,b B) )

∑ w [F - F(T ,P ,cb,bB)] j

j

j

2

(4)

j

j)1

where Fj, Tj, Pj is the jth experimental data point, b,b b) is the value calculated from function 1 with F(Tj,Pj,c parameters b c and b b for the values Tj and Pj, and Np is the number of experimental values of density taken into the correlation. Adjustable parameters were calculated by the Marquardt algorithm in double precision to minimize the influence of rounding errors. Statistical weights, wj, in eq 4, defined as

wj ) µj/(δFj)2

(5)

where δFj is the experimental uncertainty taken from the source database and either given by the authors (preferably) or estimated by a compiler for the jth density value in a correlated data set, were adjusted by varying the parameter µj (µj ) 0 for rejected values). The calculations of the parameters b c and b b were repeated until the final fit was obtained where the deviations between retained experimental and smoothed values were roughly equal to the modified experimental uncertainties, δFj/µj1/2, i.e., where the weighted standard deviation of the fit was close to unity. Results Table 3 records the values of the parameters of eq 1 for each substance (except for 1,3-dioxolane where only one experimental compressed-liquid data point was available) along with some statistical information of the fits defined as follows: Np

∑ [F - F(T ,P ,cb,bB)] /N }

RMSD ) {

2

j

j

j

1/2

(6)

p

j)1

np

∑ [1 - F(T ,P ,cb,bB)/F ] /N } 2

RMSDr/% ) 100{

j

j)1

j

j

p

1/2

(7)

Np

bias )

∑ [F - F(T ,P ,cb,bB)]/N j

j

j

p

(8)

j)1

Np

∑ sign[F - F(T ,P ,cb,bB)]‚1

(9)

sw ) [φ/(Np - NC - BB - 2)]1/2

(10)

()

j

j

j

j)1

where Np is the overall number of experimental data points retained for the correlation. The characteristics are given in an absolute density scale (kg·m-3), which is more illustrative than in a relative density scale. Temperature and pressure ranges of validity of the fits given in the table allow one to avoid extrapolation using eq 1 with the parameters from Table 3 beyond P-T areas of retained data. The T-P areas that are not rectangular are shown in the figures (Figure 1) which provide crude information on the distribution of the retained data points. Nonrectangular T-P areas appeared mostly for measurements where the T-P range approached the vicinity of a solidliquid equilibrium line. Additional correlations were performed for several substances, mostly in those cases where two contradictory data sets were available. The results (parameters and characteristics) of those fits are given for each particular substance in the text below. Table 4 summarizes some statistical information derived from the fits. Only those subsets for which the temperature and pressure ranges are displayed in the table were retained in the correlations. The statistical characteristics of these subsets refer only to the points retained in the correlation. On the other hand, the characteristics of the rejected subsets, i.e. those for which no T and P ranges are given in the table, illustrate the deviations of the rejected points from eq 1, but only for those values within T-P areas of the retained data (see Table 3 and Figure 1). Values at high temperatures of some retained sets were rejected in those cases where large deviations from the Tait equation were observed and it was not possible to improve the fit by additional parameters bi and ci. Thus the P-T ranges of some fits do not cover the entire original range of retained data sets. Often the values at temperatures above the normal boiling temperature were rejected since no reference values, F(T,Psat), were available. The temperature and/or pressure ranges were sometimes enlarged by retaining less accurate and less reliable values in the ranges beyond those of more accurate data sets but only in those cases where the representation of accurate data was not affected by the enlargement (e.g., 2-butanone; see Table 4) and the enlargement did not result in a distortion of the B(T) function. As in our previous paper [96-cib/hne] the absence of extremes and inflection points on the function B(T) (eq 3) of all final fits was checked. For 8-oxapentadecane the inflection point was found at the temperature 529 K, which is close to the upper temperature limit of the fit (553 K). Unlike with 1-alkanols and n-alkanes, where a rather large number of sets was available for nearly all selected members of the two homologous series ([94-cib/zik], [96cib/hne]), the data for the C,H,O compounds considered are,

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997 5 with few exceptions, scarce (see Table 2). This makes both the critical evaluation and the selection of recommended values rather difficult. The final fits presented in Table 3 should be regarded as smoothed representations of data from one or two sources in many cases. A comparison of isothermal compressibilities, βT ) -(1/V)(∂V/∂P)T ) (1/F)(∂F/∂P)T, calculated from the fits with available independent values published in the literature can be a guide to estimate the reliability of the P-F-T data. The values at atmospheric pressure were selected for the comparison presented in Table 5 since the compressibility values published for elevated pressures are usually evaluated from P-F-T data and thus they are not independent of data used in the correlations. The literature values of isothermal compressibility used for the comparison in Table 5 are the values obtained mostly from speed of sound measurements and were either taken directly from the papers or calculated from the equation

βT )

[

]

2

TMRP 1 1 + 2 F u cP

(11)

where M, u, RP, and cP are molar mass, speed of sound, isobaric thermal expansivity (RP ) (1/V)(∂V/∂T)P ) -(1/F)(∂F/∂T)P), and molar isobaric heat capacity, respectively. Values of input quantities in eq 11 were taken from different sources cited in Table 5. A substantial part of the speed of sound data used was obtained from the TRC Source Database (Thermodynamics Research Center, College Station, TX). It is obvious from Table 5 that the scatter of isothermal compressibilities taken from the literature is rather large: the average deviation between literature values from different sources is 2.6%; the maximum one is 8%. Outstanding values of deviations, δβT, obtained from the comparison given in Table 5 may, however, indicate significant inconsistency. In the following a brief commentary is given for each class of substances. Ethers. Surprisingly, no sufficiently accurate data were found for 3-oxapentane (diethyl ether), the substance widely used in any branch of chemistry. The only two sets which are in relatively reasonable mutual agreement (within 2 kg·m-3) are those indicated as retained in Table 4 ([31-bri], [69-bra/fre]). The results of Brazier and Freeman [69-bra/fre] for n-alkanes were mostly rejected in previous evaluation (see 96-cib/hne). On the other hand, the isothermal compressibilities calculated from the fit in Table 3 differ from literature values by about 4% on average (see Table 5). The need for new precise P-F-T measurements for this common substance is, however, obvious. Data for 4-oxaheptane (di-n-propyl ether) reported by Safarov et al. [92-saf/mad-1] for larger temperature intervals seem to be slightly less precise than the values given by Skinner et al. [68-ski/cus] for one isotherm with a precision of 1 kg·m-3. However, the Safarov values for 3-oxapentane are, on average (see bias in Table 4), lower than those by Skinner et al. The situation for 4-oxaheptane is the opposite and thus it is difficult to attribute a systematic error to any of the sets. The fit in Table 3 corresponds to Safarov’s data covering a broader temperature range, the calculated isothermal compressibility at P ) 0.1 MPa differs, however, significantly from a value taken from the literature (Table 5). The fit of eq 1 to Skinner’s data alone resulted in c0 ) 0.084 590, b0 ) 57.6582 MPa, Tmin ) Tmax ) 303.15 K, Pmax ) 499.53 MPa, RMSD ) 0.680 kg·m-3, RMSDr ) 0.083%, bias ) 0.055 kg·m-3, Np ) 10, and ( ) 4. The isothermal compressibility calculated from this fit, βT(303.15 K, 0.1 MPa) )

(1.46 ( 0.03) GPa-1, which is, however, between the literature values for T ) 298.15 K (see Table 5), seems to be more reasonable than that calculated from Safarov’s data [92-saf/mad-1]. In the case of 2,4-dimethyl-3-oxapentane (diisopropyl ether) the deviations of the magnitude in the range from 1.6 to 2.0 kg·m-3 were observed for the data measured by Govender et al. [96-gov/let] at T ) 308.15 K when the original experimental value of reference density, Fref(T ) 308.15 K, P ) 0.1 MPa) ) 708.28 kg·m-3, was used. After this value was replaced by that obtained from the smoothing equation reported by the authors, Fref(T ) 308.15 K, P ) 0.1 MPa) ) 709.83 kg·m-3, the deviations along the isotherm T ) 308.15 K decreased to the average value 0.22 kg·m-3. The experimental density at T ) 308.15 K and P ) 0.1 MPa was also rejected when the data were fit for P ) 0.1 MPa (Appendix II) due to a large deviation (-1.3 kg·m-3) from a smooth curve. Therefore, the smoothed reference density value 709.83 kg·m-3 at T ) 308.15 K was used for the final fit (Table 3). The thermal expansivity, RP ) (1/V)(∂V/∂T)P, at T ) 298.15 K and P ) 0.1 MPa evaluated from the fit in Appendix II is, however, significantly lower (1.17 kK-1) than the value by Obama et al. [85-oba/ood] (1.45 kK-1); this disagreement is similar to that observed for data for other ethers reported by Govender et al. [96-gov/let] (see below). Compressed-liquid density data reported by Schornack and Eckert [70-sch/ eck] seem to be inconsistent with the original reference values (at P ) 0.1 MPa) and thus the values at lower pressures were rejected while those at the high pressure range were retained since the effect on the fit of data at the low pressure range ([96-gov/let]) was negligible. There was only one P-F-T data set available for 5-oxanonane (di-n-butyl ether). The agreement of isothermal compressibility calculated from the fit with the value taken from the literature is -1.1% (Table 5), indicating a reliability of data measured by Senger [94-sen], which is evident also in the case of 2,5,8-trioxanonane (deviation in isothermal compressibility below 1%). The two data sets available for 6-oxaundecane (di-npentyl ether) agree within the experimental error in the range of lower pressures but deviations above 10 kg·m-3 were observed for Bridgman’s [49-bri] values at high pressures. Since the experimental temperature of Bridgman’s measurements is uncertain (room temperature reported to be about 298 K) and data at high pressures were obtained using a lead capsule to separate the sample from a hydraulic fluid, his all high-pressure data were rejected. On the other hand, all values reported by Safarov et al. [92-saf/mad] for the isobar 19.62 MPa were also rejected due to large negative deviations (-4.8 kg·m-3 in an average) from a smooth fit, indicating an erroneous pressure value. Besides that, an obvious typographical error in Safarov’s data was corrected; the original value F(T ) 414.36 K, P ) 0.101 MPa) ) 579.2 kg·m-3 was replaced by 679.2 kg·m-3. The deviation between the calculated and literature value of isothermal compressibility at P ) 0.1 MPa is rather large (-14%; see Table 5). The only data set available for 8-oxapentadecane (di-nheptyl ether, [93-saf/oso]) seems to be internally inconsistent since large deviations (10 kg·m-3 in an average) were observed at pressures below 19.6 MPa, indicating an inconsistency of compressed liquid data with densities reported for atmospheric pressure. This may be the reason why the inflection point appeared on the B(T) curve, as mentioned above. Similarly, the values for 4-oxa-1,6heptadiene reported by Safarov et al. [92-saf/gus] for pressure P ) 9.81 MPa were rejected due to large deviations (about 4 kg·m-3 in an average).

6

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997 7

Figure 1. Temperature and pressure coordinates of data points retained in the correlations for the fits where T-P areas of retained data points are not rectangular.

The deviations between the two data sets available for 2,5-dioxahexane (ethylene glycol dimethyl ether) exceed experimental uncertainties declared by the authors (0.3 kg·m-3 [94-sen], 0.4 kg·m-3 [78-sha/bai]) in the common temperature range. The fit in Table 3 corresponds to values by Senger [94-sen] over a much larger pressure range than that reported by Sharipov and Bairamova [78sha/bai] which, being correlated alone, resulted in (the maximum temperature of original smoothed reference densities was 330 K, see Appendix I) c0 ) 0.272 862, b0 ) 299.2118 MPa, b1 ) -225.3534 MPa·K-1, T0 ) 298.15 K, Tmin ) 298.15 K, Tmax ) 323.15 K, Pmax ) 35.91 MPa, RMSD ) 0.386 kg·m-3, RMSDr ) 0.046%, bias ) -0.107 kg·m-3, Np ) 12, ( ) 0. The isothermal compressibility, βT(T ) 303.15 K, P ) 0.1 MPa), calculated from this fit differs from that calculated from the fit in Table 3 by -18%. The parameter c0 (and of bi as well) of this fit has a value unusually high for the Tait equation. Similarly high values were obtained for 4,7,10-trioxatridecane (diethylene glycol dipropyl ether; see Table 3) for the fit of data from the same laboratory [81-sha/abd]. Senger [94-sen] measured P-F-T data for several ethers using a bellows piezometer and presented all the experimental values along each isotherm on the increase of pressure up to the maximum one and then on the decrease to a low pressure range. A hysteresis was observed when correlating his data for 3,3-dimethyl-2-oxabutane (methyl tert-butyl ether) and 4,4-dimethyl-3-oxapentane (ethyl tertbutyl ether); the deviations from the eq 1 were negative for the pressure-on-increase data points and positive for decreasing pressure. The hysteresis resulted in rather higher values of RMSD for these two ethers compared to those measured by Senger for other ethers where the hysteresis was much less pronounced. The effect seems to be symmetrical since the values of bias for all ethers are comparable. The agreement of relative densities, F(T,P)/F(T,Pref ) 0.1 MPa) reported by Senger [94-sen] and Govender et al. [96-gov/let] for 3,3-dimethyl-2-oxabutane (methyl tert-butyl ether) and 3,3-dimethyl-2-oxapentane (methyl tert-pentyl ether) is satisfactory (see Table 4). Large discrepancies were, however, observed for reference values (densities at P ) 0.1 MPa) where maximum deviations between the two sets were as high as 10 kg·m-3; the data [96-gov/let] yield lower values of thermal expansivity, RP ) (1/V)(∂V/∂T)P, than other sources (see also discussion for cyclic ethers below). At T ) 298.15 K and P ) 0.1 MPa the values of RP for 3,3-dimethyl-2-oxabutane and 3,3dimethyl-2-oxapentane are RP ) 1.11 kK-1 [96-gov/let], 1.47 kK-1 [94-sen], 1.42 kK-1 [85-oba/ood], and RP ) 0.96 kK-1 [96-gov/let], 1.25 kK-1 [94-sen], respectively. Senger’s values of RP are in good agreement with the literature data

also for 4,4-dimethyl-3-oxapentane (ethyl tert-butyl ether); RP(T ) 298.15 K, P ) 0.1 MPa) ) 1.45 kK-1 [94-sen], 1.40 kK-1 [85-oba/ood]. Since Senger’s values are not currently available and are in better agreement with other literature data, the fits of data at P ) 0.1 MPa by Senger [94-sen] are presented in Appendix II; the values reported by Govender et al. [96-gov/let] are easily available from the original source. Similarly as for 4-oxaheptane, the negative deviations of values reported by Skinner et al. [68-ski/cus] for methoxybenzene from the data measured by Kuss and Taslimi [70-kus/tas] were observed. The final fit corresponds to the latter data set; the fit of Skinner’s data resulted in c0 ) 0.081 446, b0 ) 125.8382 MPa, Tmin ) Tmax ) 303.15 K, Pmax ) 497.51 MPa, RMSD ) 1.808 kg·m-3, RMSDr ) 0.166%, bias ) 0.022 kg·m-3, Np ) 10, ( ) 0. The isothermal compressibility, βT(T ) 303.15 K, P ) 0.1 MPa), calculated from this fit differs from that calculated from the fit in Table 3 by -4.2%. The P-F-T data for cyclic ethers are scarce. One experimental value was found for 1,3-dioxolane ([83-nak/ miy]; {F(P ) 101.3 MPa)/F(P ) 0.1 MPa) - 1} ) 0.055 39 at T ) 298.15 K), and therefore no correlation was performed. Data for tetrahydrofuran reported by Schornack and Eckert [70-sch/eck] are of low accuracy and show an internal inconsistency, particularly at lower pressures. The data at higher pressures were, however, retained in the final fit to enlarge the pressure range. Two values presented for 1,4-dioxane in reference 68-pea/str for T ) 298.15 K are reasonably consistent with the data measured by Govender et al. [96-gov/let] in the lower pressure range. The rejected value reported by Korpela and Koskikallio [66kor/kos] for T ) 298.15 K and P ) 67.3 MPa differs from the final fit (Table 3) by 5.4 kg·m-3. Deviations of isothermal compressibilities, βT(T,P ) 0.1 MPa), calculated from the fits presented for tetrahydrofuran and 1,4-dioxane in Table 3 from the values obtained from the literature data are below 6 and 8%, respectively, except for those cases where density and thermal expansivity used in eq 11 were evaluated from the F(T,P ) 0.1 MPa) data by Govender at al. [96-gov/let] (see Table 5). Similarly as in the case of 2,4-dimethyl-3-oxapentane, 3,3-dimethyl-2-oxabutane, and 3,3-dimethyl-2-oxapentane (see above), large deviations of the F(T,P ) 0.1 MPa) values [96-gov/let] from other available data were observed, resulting in significantly lower values of thermal expansivity, RP. Therefore the values of isothermal compressibility, βT, calculated from eq 11 using the F(T,P ) 0.1 MPa) data by Govender at al. [96-gov/let] are lower (compared to other literature values in Table 5) and not consistent even with relative densities, F(T,P)/F(T,Pref ) 0.1 MPa) reported in 96-gov/let; the values

8

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997

Table 2. Characteristics of Data Sets: Overall Number of Data Points, Np, Temperature and Pressure Ranges within the Liquid State, Tmin, Tmax, Pmin, and Pmax, Experimental Method Used, Types of Data, and Purities of Measured Samples ref

Np

Tmin/K

Tmax/K

13-bri 31-bri 57-wal/ric 68-ski/cus 69-bra/fre 92-saf/mad

119 26 2 11 8 88

293.15 303.15 294.15 303.15 303.15 296.71

353.15 348.15 305.15 303.15 303.15 462.18

total

254

293.15

462.18

Pmin/MPa

Pmax/MPa

3-Oxapentane (Diethyl Ether) 49.0 1176.8 49.1 1176.9 4180.0 9610.0 82.1 500.6 50.0 400.0 4.9 98.1 4.9

metha

data typeb

vs vb sw vl vb bu

D D D D D D

vl bu

D D

D Df

99.8me

99d

9610.0

68-ski/cus 92-saf/mad-1

11 110

303.15 294.30

4-Oxaheptane (Di-n-propyl Ether) 303.15 49.7 499.5 524.80 4.9 98.1

total

121

294.30

524.80

70-sch/eck 96-gov/let

12 45

303.15 288.15

2,4-Dimethyl-3-oxapentane (Diisopropyl Ether) 323.15 45.7 511.3 vb 328.15 0.5 8.0 mo

total

57

288.15

328.15

90

298.15

5-Oxanonane (Di-n-butyl Ether) 328.15 5.1 203.7

vb

D

49-bri 92-saf/mad

11 132

298.15 296.64

6-Oxaundecane (Di-n-pentyl Ether) 298.15 49.0 980.7 561.57 4.9 98.1

vs bu

D D

total

143

296.64

561.57

8-Oxapentadecane (Di-n-heptyl Ether) 553.00 4.9 98.1

bu

D

94-sen

93-saf/oso

154

293.00

94-sen 96-gov/let

90 45

298.15 288.15

135

288.15

total

4.9

0.5

4.9

499.5

511.3

980.7

3,3-Dimethyl-2-oxabutane (Methyl tert-Butyl Ether) 328.15 5.4 207.7 vb 328.15 0.5 8.0 mo 328.15

0.5

94-sen

90

298.15

94-sen 96-gov/let

90 45

298.15 288.15

3,3-Dimethyl-2-oxapentane (Methyl tert-Pentyl Ether) 328.15 5.6 203.8 vb 328.15 0.5 8.0 mo

135

288.15

78-sha/bai 94-sen total

48 90

298.15 298.15

138

298.15

328.15

0.5

1.8

94-sen

90

298.15

81-sha/abd

69

298.15

4,7,10-Trioxatridecane (Diethylene Glycol Dipropyl Ether) 523.15 2.2 35.9 pi

90-sve/sid

5

92-saf/gus

121

291.70

4-Oxa-1,6-heptadiene (Diallyl Ether) 552.30 4.9 99.1

bu

68-ski/cus 70-kus/tas

10 20

303.15 298.15

total

30

298.15

353.15

70-sch/eck 71-ham/smi 83-nak/miy 87-hol/goe 96-gov/let

12 1 1 5 45

303.15 303.15 298.15 293.15 288.15

323.15 303.15 298.15 293.15 328.15

total

64

288.15

328.15

1

298.15

298.15 328.15

45

>99d

D Df

98d >99.9me

D D

99.94we 99d

D

99d

D

2,5,8,11,14-Pentaoxapentadecane (Tetraethylene Glycol Dimethyl Ether) 293.15 293.15 2.0 10.0 mo Df

Methoxybenzene (Methyl Phenyl Ether) 303.15 59.3 497.5 vl 353.15 39.2 196.1 vl

96-gov/let

D

204.8

2,5,8-Trioxanonane (Diethylene Glycol Dimethyl Ether) 328.15 5.1 202.8 vb

83-nak/miy

99d >99.9me

203.8

2,5-Dioxahexane (Ethylene Glycol Dimethyl Ether) 473.15 1.8 36.6 pi 328.15 5.6 204.8 vb 473.15

D Df

207.7

4,4-Dimethyl-3-oxapentane (Ethyl tert-Butyl Ether) 328.15 5.6 207.2 vb

total

288.15

39.2

99.5e

D D D

497.5

Tetrahydrofuran (Oxolane) 46.7 517.0 101.3 101.3 101.3 101.3 2.0 10.0 0.5 8.0

vb va va mo mo

D D D Df Df

1,3-Dioxolane 101.3 101.3

va

D

Tetrahydropyran (Oxane) 0.5 8.0

mo

Df

0.5

sample purityc %

99d >99d >99.9me

517.0

>99.9me

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997 9 Table 2 (Continued) ref

metha

data typeb

sample purityc %

va va mo

D S Df

>99.9me

897.0

vb

D

>99e

Dibenzofuran 0.5 25.5

vs

D

99.99me

vs va va sw vb vb vb vs hp vs vb mo mo vb mo va

D D D D F F F D D D D Df D D D D

va hp hp vs vb

F D D D D

>99.9md

Np

Tmin/K

Tmax/K

Pmin/MPa

66-kor/kos 68-pea/str 96-gov/let

1 2 45

298.15 298.15 288.15

298.15 298.15 328.15

total

48

288.15

328.15

0.5

78-fig/szw

191

209.00

257.00

11.0

84-nas/siv

42

391.55

563.15

13-bri 51-new/wea 56-stu 57-wal/ric 66-win/pow 66-win/pow 66-win/pow 67-ada/lai 76-ato/mam 77-gup/han 80-rae/fin 87-hol/goe-1 87-nhu/bha 91-mal/woo 91-pap/zia 92-ego/gru

109 1 1 2 4 4 9 7 48 24 49 5 5 105 9 5

293.15 298.15 303.15 299.15 273.15 273.15 273.15 299.76 273.15 273.15 298.15 293.15 293.15 278.15 298.15 298.15

353.15 298.15 303.15 303.15 273.15 273.15 273.15 299.76 473.15 363.15 398.15 293.15 293.15 323.15 298.15 298.15

total

387

273.15

473.15

Pmax/MPa

1,4-Dioxane 67.3 25.0 0.5

67.3 50.0 8.0 67.3

Furan

2-Propanone (Dimethyl Ketone) 49.0 1176.8 101.3 101.3 101.3 101.3 4640.0 10580.0 34.5 206.8 34.5 206.8 34.5 586.1 40.0 100.0 20.3 162.1 2.8 22.1 1.0 411.9 2.0 10.0 2.0 10.0 2.5 392.3 2.0 33.8 5.0 60.0 1.0

>99.8me 99.99e 99.9md 99.5d

10580.0

2-Butanone (Methyl Ethyl Ketone) 167.9 305.1 9.8 127.5 40.5 162.1 35.0 172.0 2.3 282.5

63-and 74-ato/mam 76-ato/bag 77-lam/hun 92-mal/woo

9 243 77 15 138

283.15 283.15 273.15 303.15 278.15

308.15 473.15 473.15 343.15 338.15

total

482

273.15

473.15

273.00

2-Pentanone (Methyl n-Propyl Ketone) 472.24 5.0 78.6 bu

D

99.86e

3-Pentanone (Diethyl Ketone) 9.8 156.8 2.5 389.8

hp vb

D D

>99.0md

77-apa/ker

36

2.3

305.1

82-ato/mam 93-mal/pri

90 128

293.00 278.15

473.00 338.15

total

218

278.15

473.00

90

293.15

2-Hexanone (Methyl n-Butyl Ketone) 473.15 9.8 156.9

hp

D D

4-Heptanone (Di-n-propyl Ketone) 10.0 160.0

hp

D

bu bu

D D

298.15

Cyclopentanone 50.0 400.0

vb

D

Cyclohexanone 158.7 266.1 10.0 220.0

va vs

F S

vs

D

79-ato

2.5

389.8

63-and

13

295.55

4-Methyl-2-pentanone (Methyl Isobutyl Ketone) 295.55 245.2 484.8 va

91-ato

108

273.00

473.00

88 44

273.15 273.15

2-Octanone (Methyl n-Hexyl Ketone) 473.15 20.3 162.1 566.08 5.0 78.6

132

273.15

566.08

75-ato/mam 78-apa/ker total 69-bra/fre

8

298.15

63-and 82-wis/wue

3 93

296.45 253.20

296.45 303.40

total

96

253.20

303.40

5.0

10.0

162.1

266.1

68-cha/sta

10

295.15

295.15

Ethanal (Acetaldehyde) 13.9 138.0

68-cha/sta

10

296.65

296.65

Propanal (Propionaldehyde) 13.9 138.0

vs

D

Butanal (Butyraldehyde) 13.9 138.0 34.9 276.6

vs vs

D D

vs

D

68-cha/sta 71-run/sta

10 32

302.04 303.15

302.04 333.15

total

42

302.04

333.15

301.37

2-Methylpropanal (Isobutyraldehyde) 301.37 13.9 138.0

68-cha/sta

10

13.9

276.6

99.9e

10

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997

Table 2 (Continued) metha

data typeb

bu

D

99.8md

vs bu

D D

>99.8md

295.21

Heptanal (Enanthaldehyde) 13.9 138.0

vs

D

293.87

Octanal (Caprylic Aldehyde) 13.9 138.0

vs

D

vs

D

va va

F F

va

F

ref

Np

Tmin/K

Tmax/K

75-mam/gus

48

248.15

545.15

68-cha/sta 75-mam/gus

10 52

300.37 284.95

3-Methylbutanal (Isovaleraldehyde) 300.37 13.9 138.0 580.36 5.0 50.1

total

62

284.95

580.36

68-cha/sta 68-cha/sta 68-cha/sta

10 10

295.21 293.87

Pmin/MPa

Pmax/MPa

Pentanal (Valeraldehyde) 5.0 50.1

5.0

sample purityc %

138.0

Benzaldehyde 13.9 138.0

10

295.21

295.21

63-and 71-kor

2 4

295.55 298.15

295.55 298.15

total

6

295.55

298.15

12

298.15

328.15

298.15

Propanoic Acid (Propionic Acid) 328.15 50.7 253.3

va

F F

99.8e

71-kor 71-kor

15

Methanoic Acid (Formic Acid) 76.5 107.5 50.7 202.7 50.7

98d

202.7

Ethanoic Acid (Acetic Acid) 50.7 253.3

71-kor

15

298.15

2-Methylpropanoic Acid (Isobutyric Acid) 328.15 50.7 253.3 va

92-ban/gar

30

343.15

373.15

Octanoic Acid (Caprylic Acid) 1.0 9.0

mo

Df

>99.5md

92-ban/gar

30

343.15

373.15

Decanoic Acid (Capric Acid) 1.0 9.0

mo

Df

>99md

92-ban/gar

30

343.15

373.15

Dodecanoic Acid (Lauric Acid) 1.0 9.0

mo

Df

>99.5md

92-ban/gar

25

353.15

Tetradecanoic Acid (Myristic Acid) 373.15 1.0 9.0

mo

Df

>99.5md

92-ban/gar

25

353.15

373.15

Hexadecanoic Acid (Palmitic Acid) 1.0 9.0

mo

Df

>99md

78-kum/iwa

32

253.15

Methyl Ethanoate (Methyl Acetate) 313.15 19.7 156.8

vl

D

97.0d

49-bri 63-and 70-sch/eck 75-gus/kad 79-kum/iwa

17 1 12 42 32

298.15 298.15 303.15 300.06 253.15

298.15 298.15 323.15 499.21 313.15

vs va vb bu vl

D S D D D

99.8e 99d

104

253.15

499.21

1-Methylethyl Ethanoate (Isopropyl Acetate) 531.22 5.0 49.1 bu

D

99.8e

total

Ethyl Ethanoate (Ethyl Acetate) 49.0 3922.7 466.1 466.1 51.5 512.7 5.0 49.1 19.7 156.8 5.0

3922.7

75-gus/kad

48

297.17

32-bri

32

1,2,3-Propanetriyl Triethanoate (Glyceryl Triacetate; Triacetin) 273.15 368.15 49.0 1176.8 vb

D

78-gus/kli

66

300.00

Propyl Propanoate (n-Propyl Propionate) 550.00 5.0 50.0 bu

76-gus/kli

78

298.15

3-Methylbutyl Propanoate (Isopentyl Propionate) 598.15 5.0 50.1 bu

92-mus/gus

90

294.99

Methyl Hexanoate (Methyl Caproate) 589.63 4.9 58.8

bu

D

99.88e

119

289.00

Nonyl Hexanoate (n-Nonyl Caproate) 604.82 4.9 58.8

bu

D

99.32e

92-mus/gus-1 32-bri

36

S

99.8we

S

99.7e

1,2,3-Propanetriyl Trihexanoate (Glyceryl Trihexanoate; Tricaproin) 273.15 368.15 49.0 1176.8 vb

D D

99.68e

91-gus/kul

121

2-Methylpropyl 2-Hydroxypropanoate (Isobutyl Lactate) 294.36 533.89 4.9 98.1 bu

91-gus/kul-1

121

296.71

Pentyl 2-Hydroxypropanoate (n-Pentyl Lactate) 535.03 4.9 98.1 bu

D

99.48e

94-mus/tag

105

300.48

Methyl Benzenecarboxylate (Methyl Benzoate) 604.58 5.0 58.9 bu

D

99.3e

88-wal/lam

60

253.15

2-Ethylhexyl Benzenecarboxylate (2-Ethylhexyl Benzoate) 373.15 50.0 450.0 nd

D

>99.8d

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997 11 Table 2 (Continued) Tmax/K

Pmin/MPa

Pmax/MPa

metha

data typeb

sample purityc %

ref

Np

Tmin/K

90-mus/gan-1g

72

298.15

Methyl 2-Hydroxybenzenecarboxylate (Methyl Salicylate) 573.15 10.0 60.0 bu

D

99.7e

90-mus/gan-1

72

298.15

Pentyl 2-Hydroxybenzenecarboxylate (n-Pentyl Salicylate) 573.15 10.0 60.0 bu

D

99.7e

90-mus/gan-1

72

298.15

Hexyl 2-Hydroxybenzenecarboxylate (n-Hexyl Salicylate) 573.15 10.0 60.0 bu

D

99.7e

D

99.92d 99.94e,h

87-gus/bai

142

289.34

Methyl 2-Methyl-2-propenoate (Methyl Methacrylate) 424.77 5.0 98.1 bu

89-gus/bai

78

292.37

Nonyl 2-Methyl-2-propenoate (n-Nonyl Methacrylate) 473.43 5.0 98.2 bu

D

273.15

Methyl (Z)-9-Octadecenoate (Methyl Oleate) 368.15 49.0 980.7 vb

D

32-bri

22

Diethyl 2,2-Bis(phenylmethyl)-propane-1,3-dioate (Diethyl Dibenzylmalonate) 273.15 368.15 49.0 490.3 vb D

32-bri

13

90-mus/gan-3

54

295.65

90-mus/gan-2

60

288.15

91-mus/gan

72

32-bri

37

92-uos/kit

4

Diethyl Butane-1,4-dioate (Diethyl Succinate) 498.15 5.0 49.1 bu

D

98.6e

Dipropyl Butane-1,4-dioate (Di-n-propyl Succinate) 502.75 5.0 49.1 bu

D

98.7e

298.15

Dinonyl Butane-1,4-dioate (Di-n-nonyl Succinate) 573.15 10.0 60.0 bu

D

99.37e

273.15

Dibutyl Benzene-1,2-dicarboxylate (Di-n-butyl Phthalate) 368.15 49.0 1176.8 vb

D

298.15

4-Methyl-1,3-dioxolan-2-one (Propylene Carbonate) 298.15 50.0 200.0 va

D

a Method used for measurements: bu, buoyancy method; mo, mechanical oscillator method; nd, not described or stated in the reference; pi, piezometer of unspecified type; sw, shock wave method; va, Aime method; vb, variable-volume cell with bellows; vl, variable-volume cell with liquid piston; vs, variable-volume cell with solid piston. For the classification and description of the methods, see [85-tek/cib]. b D, direct experimental data; S, smoothed data presented in the reference; F, values calculated from smoothing equation reported by the researchers. c No letter, unspecified percent; m, mole percent; w, mass percent. d Only purity of source material is given. e Final purity of the sample. f IPTS-68 declared by the researchers. g Same data are presented also in 90-mus/gan. h Purified sample was stabilized with 0.05 mass % of hydrochinone to prevent a polymerization.

of βT(T ) 298.15 K, P ) 0.1 MPa) evaluated by Govender et al. [96-gov/let] from their data are 0.960 GPa-1 (tetrahydrofuran) and 0.739 GPa-1 (1,4-dioxane). It might be concluded that while the compression data (relative densities) along the isotherms seem to be correct, the temperature dependencies of density itself need to be reexamined. There was one data set available for tetrahydropyran [96-gov/let]. The agreement of the value of βT(T ) 298.15 K, P ) 0.1 MPa) calculated from the fit with the value selected from the literature is very good (-0.4%, Table 5). Table A2 (Appendix II) presents the fit of data at P ) 0.1 MPa; it is likely that the value of the parameter v1 of the smoothing equation presented in the original source [96gov/let] is in error; the correct value should be probably 0.076 166 (not 0.761 66), as deduced from tentative calculations of densities at P ) 0.1 MPa. Besides that, it should be pointed out that, similarly as with other ethers measured by Govender et al. [96-gov/let], the values of thermal expansivity RP are significantly lower (e.g., RP(T ) 298.15 K, P ) 0.1 MPa) ) 0.776 kK-1) than those evaluated from other literature data (83-ing/gro: RP(T ) 298.15 K, P ) 0.1 MPa) ) 1.15 kK-1). Data of furan measured by Figuiere and Szwarc [78-fig/ szw] are of low accuracy (RMSD ) 2.4 kg·m-3); the authors primarily investigated solid-liquid equilibrium and the P-F-T measurements were of secondary importance. Experimental data of dibenzofuran [84-nas/siv] correlated by the authors using a modified Chueh equation with 20 parameters resulted in the relative RMSDr slightly lower (0.07%) than that of the fit by eq 1 with four adjustable parameters (Table 3). It was, however, impossible to improve the fit by additional parameters since the extreme appeared on the B(T) curve. Ketones (Alkanones and Cyclohexanone). There is a rather large number of data sets available for 2-pro-

panone. The evaluation revealed that only a few data sets measured recently in a close-to-ambient temperature range are in a mutual agreement. It was not possible to extend the temperature range by an inclusion of some less accurate data sets since inflection points appeared on the B(T) curve indicating the inconsistency of data. The extension was possible in the case of 2-butanone by retaining the high-temperature data points from the set of Atoyan et al. [76-ato/bag] but the expected uncertainty in this temperature range might be rather high (RMSD ) 2.5 kg·m-3; see Table 4). The agreement between values of βT(T,P ) 0.1 MPa) calculated from the fits for those two alkanones and data taken from the literature is satisfactory (see Table 5), even for 2-butanone at temperatures beyond Malhotra’s [92-mal/woo] experimental temperature range. There is only one data set available for 2-pentanone: a comparison of smoothed values with those from the generalized Tait equation (see below and Table 6) shows a satisfactory agreement (0.16%); however, the isothermal compressibilities (Table 5) calculated from the fit in Table 3 are lower than selected literature values. The data set by Atoyan and Mamedov [82-ato/mam] for 3-pentanone is inconsistent with data measured by Malhotra et al. [93mal/pri] and since the data from Malhotra’s laboratory proved to be of high quality in the case of 2-propanone and 2-butanone, the latter set only was retained. Data available for 2-hexanone seem to be of poor accuracy. The values of isothermal compressibility calculated from the fit for P ) 0.1 MPa differ from the values taken from the literature by nearly -20% at lower temperatures (see Table 5) and are even out of a monotonous decrease within the homologous series of 2-alkanones indicated by the literature data. Besides that, the deviations of relative density from the generalized Tait equation (see below and

12

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997

Table 3. Parameters ci, bi, and T0 of Eq 1, Temperature and Pressure Ranges,a Tmin, Tmax, Pmin, and Pmax, Absolute, RMSD, and Relative, RMSDr, Root Mean Square Deviations, Biases, bias, Number of Data Points, Np, (, and Weighted Standard Deviations, sw Ethers 3-oxapentane c0 b0/MPa b1/MPa‚K-1 b2/MPa‚K-2 b3/MPa‚K-3 T0/K Tmin/K Tmax/K Pmin/MPa Pmax/MPa RMSD/kg‚m-3 RMSDr/% bias/kg‚m-3 Np ( sw

4-oxaheptane

2,4-dimethyl-3oxapentane

5-oxanonane

0.095070 0.085992 46.6780 50.2436 -43.4590 -38.7232 15.5294

0.088836 45.5640 -55.9497 14.5106

0.090642 0.133853 74.8969 143.6450 -47.3687 -103.5338 27.0944

303.15 303.15 348.15 49.13 1176.90 1.220 0.138 -0.098 33 -1 0.957

303.15 288.15 328.15 0.50 511.29 1.172 0.135 0.062 52 4 1.031

298.15 298.15 328.15 5.08 203.68 0.233 0.029 0.020 90 -2 0.955

294.30 294.30 374.50 4.91 98.10 1.361 0.183 0.224 40 6 1.000

8-oxapentadecane

6-oxaundecane

298.15 296.64 456.82 4.91 98.10 1.429 0.189 0.043 80 6 1.069

0.156481 198.1315 -153.7136 55.2218 -7.8176 293.00 293.00 553.00 19.62 98.10 1.793 0.228 -0.095 113 -13 1.020

2,5,8,11,142,5,8-tri4,7,10-tripentaoxa4-oxa-1,6- methoxyoxanonane oxatridecane pentadecane heptadiene benzene c0 b0/MPa b1/MPa‚K-1 b2/MPa‚K-2 T0/K Tmin/K Tmax/K Pmin/MPa Pmax/MPa RMSD/kg‚m-3 RMSDr/% bias/kg‚m-3 Np ( sw

0.089658 109.6532 -82.7022 25.4503 298.15 298.15 328.15 5.08 202.81 0.173 0.018 0.013 90 8 1.040

0.363718 362.4873 -250.7135

0.086177 137.1726

348.15 298.15 348.15 2.18 35.94 0.392 0.045 -0.114 22 -6 1.094

293.15 293.15 293.15 2.00 10.00 0.007 0.001 -0.001 5 -1 0.973

0.185068 163.5259 -95.2772 50.3120 291.70 291.70 365.00 4.91 98.10 1.680 0.230 0.140 38 6 1.030

3,3-di4,4-di3,3-dimethyl-2- methyl-3methyl-2- 2,5-dioxaoxabutane oxapentane oxapentane hexane 0.091636 52.6240 -41.6220 25.9452

0.086511 48.4404 -35.0754

0.087240 64.0716 -49.9481 13.4133

0.092603 83.5587 -65.9447

298.15 288.15 328.15 0.50 207.72 0.765 0.095 0.054 134 -10 1.066

298.15 298.15 328.15 5.56 207.16 0.483 0.062 0.015 90 0 1.122

298.15 288.15 328.15 0.50 203.79 0.290 0.036 -0.011 135 7 1.170

298.15 298.15 328.15 5.58 204.75 0.225 0.025 0.028 90 10 0.920

tetrahydrofuran

0.095902 0.092962 142.0376 87.2488 -77.7516 -90.0809 75.8269 303.15 303.15 298.15 288.15 353.15 328.15 39.23 0.50 196.13 516.96 0.158 0.907 0.015 0.091 0.000 -0.027 20 58 2 16 1.086 1.280

tetrahydropyran

1,4dioxane

0.055469 56.1224 -59.8283 49.5308 298.15 288.15 328.15 0.50 8.00 0.094 0.011 -0.009 45 -5 0.991

0.042888 54.3581 -47.0832 33.6213 298.15 288.15 328.15 0.50 50.00 0.273 0.026 0.024 47 3 1.007

furan

dibenzofuran

0.094453 0.017847 123.0858 12.0064 -68.6050 -6.4553 1.2142 257.00 423.15 209.00 391.55 257.00 563.15 11.00 0.51 897.00 25.53 2.385 1.080 0.213 0.103 0.001 0.037 185 38 49 -2 0.955 1.324

Ketones and Aldehydes 222324-methyl4propanone butanone pentanone pentanone hexanone 2-pentanone heptanone c0 c1/K-1 b0/MPa b1/MPa‚K-1 b2/MPa‚K-2 b3/MPa‚K-3 b4/MPa‚K-4 T0/K Tmin/K Tmax/K Pmin/MPa Pmax/MPa RMSD/kg‚m-3 RMSDr/% bias/kg‚m-3 Np ( sw

0.099239

0.095009 -0.003291 80.3063 71.7822 -75.4324 -62.6158 37.3329 23.6819 -8.7208 1.6959 293.15 313.15 278.15 278.15 323.15 473.15 2.00 2.32 392.25 282.45 0.266 1.079 0.032 0.137 0.058 0.003 124 165 26 3 1.028 0.931 ethanal

c0 b0/MPa b1/MPa‚K-1 b2/MPa‚K-2 T0/K Tmin/K

propanal

0.087406

0.094603

107.5762 -87.2636

273.00 273.00 315.66 5.01 78.58 0.279 0.033 -0.054 18 -2 1.163

butanal

0.107840 0.120241 0.091785 72.5470 110.1100 102.7158 -38.5961 -97.6281 295.15 296.65 302.04 295.15 296.65 303.15

0.085246

0.099088

0.102388

90.6753 106.7265 -69.3353 -106.2848 19.0573 59.3556 -16.7670

99.9725

298.15 278.15 338.15 2.53 389.82 0.307 0.036 0.087 128 36 1.025

295.55 295.55 295.55 245.21 484.84 0.802 0.085 0.029 13 -3 0.999

293.15 293.15 393.15 9.81 156.91 0.990 0.125 -0.132 53 3 0.921

2-methylpropanal

pentanal

0.103047 79.8182

0.071630 74.4381 -20.4294 -12.2063 248.15 248.15

301.37 301.37

2octanone 0.113614

cyclocyclopentanone hexanone 0.098473

0.091558

150.4746 155.4195 -121.9168 -103.9260 35.0029 17.5846

95.7265

135.5573 -52.1027 130.4980

273.00 273.00 403.00 10.00 160.00 1.102 0.129 -0.012 71 17 1.133

298.15 298.15 298.15 50.00 400.00 5.847 0.565 -0.318 8 0 1.017

303.40 253.20 303.40 10.00 266.08 0.699 0.071 -0.033 96 8 1.003

273.15 273.15 374.31 5.01 78.58 0.550 0.067 -0.070 25 -7 1.006

3-methylbutanal heptanal 0.094111 82.1858 -45.1467 -19.1201 300.37 284.95

octanal

benzaldehyde

0.102239 0.102738 112.9950 121.6201

0.094041 154.0605

295.21 295.21

295.21 295.21

293.87 293.87

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997 13 Table 3 (Continued) Ketones and Aldehydes (Continued)

Tmax/K Pmin/MPa Pmax/MPa RMSD/kg‚m-3 RMSDr/% bias/kg‚m-3 Np ( sw

ethanal

propanal

butanal

2-methylpropanal

pentanal

3-methylbutanal

heptanal

octanal

benzaldehyde

295.15 13.89 138.00 0.158 0.019 0.001 10 -2 0.989

296.65 13.89 138.00 0.130 0.016 -0.002 10 0 1.021

333.15 35.61 276.58 0.592 0.069 -0.075 25 -5 1.140

301.37 13.89 138.00 0.258 0.031 -0.033 10 0 1.028

374.15 5.00 50.08 0.586 0.075 0.005 24 -6 1.092

362.35 5.00 50.08 0.343 0.044 -0.015 16 -4 0.963

295.21 13.89 138.00 0.073 0.009 -0.007 10 -2 0.924

293.87 13.89 138.00 0.098 0.012 0.005 10 0 1.016

295.21 13.89 138.00 0.180 0.017 0.032 10 -2 1.035

Acids

c0 b0/MPa b1/MPa‚K-1 b2/MPa‚K-2 T0/K Tmin/K Tmax/K Pmin/MPa Pmax/MPa RMSD/kg‚m-3 RMSDr/% bias/kg‚m-3 Np ( sw

methanoic acid

ethanoic acid

propanoic acid

2-methylpropanoic acid

octanoic acid

decanoic acid

dodecanoic acid

tetradecanoic

hexadecanoic acid

0.096327 148.7378 -443.7460

0.092418 90.6714 -62.2302 19.4216 313.15 298.15 328.15 50.66 253.31 0.098 0.009 0.000 12 2 0.086

0.091314 98.6259 -69.5680 20.6000 298.15 298.15 328.15 50.66 253.31 0.091 0.009 0.003 15 3 0.088

0.087375 86.9541 -55.0296

0.066987 66.0320 -56.5565 73.2502 343.15 343.15 373.15 1.00 9.00 0.068 0.008 0.006 30 4 0.956

0.093916 101.8285 -59.7045

0.067638 75.0552 -39.1829

0.173801 198.6292 -105.5458

0.115340 136.1333 -85.2892

343.15 343.15 373.15 1.00 9.00 0.059 0.007 -0.001 30 0 1.017

343.15 343.15 373.15 1.00 9.00 0.054 0.006 0.000 30 -2 0.939

353.15 353.15 373.15 1.00 9.00 0.054 0.006 0.001 25 1 0.929

353.15 353.15 373.15 1.00 9.00 0.043 0.005 0.000 25 1 0.855

298.15 295.55 298.15 50.66 202.65 0.047 0.004 0.002 6 2 0.036

298.15 298.15 328.15 50.66 253.31 0.272 0.027 0.004 15 -1 0.266 Esters

methyl ethyl 1-methylethyl ethanoate ethanoate ethanoate c0 b0/MPa b1/MPa‚K-1 b2/MPa‚K-2 b3/MPa‚K-3 T0/K Tmin/K Tmax/K Pmin/MPa Pmax/MPa RMSD/kg‚m-3 RMSDr/% bias/kg‚m-3 Np ( sw

c0 b0/MPa b1/MPa‚K-1 b2/MPa‚K-2 b3/MPa‚K-3 T0/K Tmin/K Tmax/K Pmin/MPa Pmax/MPa RMSD/kg‚m-3 RMSDr/% bias/kg‚m-3 Np ( sw

0.087851 0.089409 94.1389 91.8722 -74.2636 -81.9526 49.0679 -18.2587 273.15 273.15 253.15 253.15 313.15 343.15 19.66 5.00 156.75 156.75 0.356 0.952 0.035 0.106 -0.003 -0.206 30 49 0 -1 1.020 1.018

1,2,3-propane1,2,3-propanetriyl tripropyl 3-methylbutyl methyl nonyl triyl triethanoate propanoate propanoate hexanoate hexanoate hexanoate

0.106954 94.1343 -103.4575 53.7186

0.098843 145.0897 -53.7953 31.4770

0.103066 95.8443 -71.1831 22.9642

0.085373 89.9136 -67.6642 16.2675

0.091386 70.7425 -44.7245 9.1129

297.17 297.17 367.20 5.00 49.10 0.625 0.071 -0.088 18 0 0.999

368.15 273.15 368.15 49.03 1176.80 1.314 0.102 0.084 32 0 1.016

300.00 300.00 400.00 5.00 50.00 1.884 0.215 0.118 30 -6 0.960

298.15 298.15 423.15 5.00 50.08 0.794 0.102 -0.031 32 -2 0.908

294.99 294.99 408.85 4.90 58.80 0.660 0.078 0.020 33 -1 1.044

methyl 2-hydroxybenzenecarboxylate

pentyl 2-hydroxybenzenecarboxylate

hexyl 2-hydroxybenzenecarboxylate

methyl 2-methyl-2propenoate

0.134172 240.8968 -153.0592 53.3590 -8.3332 298.15 298.15 498.15 10.00 60.00 0.372 0.034 0.035 54 8 0.957

0.165532 204.0698 -92.0613 23.1511 -2.6619 298.15 298.15 573.15 10.00 60.00 0.484 0.049 -0.019 71 -1 1.099

0.228551 150.5257 -34.7764 3.1064

0.094277 98.2396 -73.7312 8.3110

298.15 298.15 573.15 10.00 60.00 0.213 0.028 -0.023 72 -6 0.934

300.06 289.34 349.29 5.00 98.10 0.430 0.045 -0.008 61 -9 0.978

2-methylpropyl 2-hydroxypropanoate

pentyl 2-hydroxypropanoate

methyl benzenecarboxylate

2-ethylhexyl benzenecarboxylate

0.060907 110.5039 -3.5979

0.034262 42.2839 -12.9463

0.110587 193.5738 -105.9694 17.6617

0.097846 157.7459 -82.1159 14.0075

294.36 294.36 343.41 4.91 98.10 0.554 0.055 0.079 29 5 1.193

296.71 296.71 371.82 4.90 98.10 0.920 0.095 0.089 37 -3 0.949

300.48 300.48 440.59 5.00 58.90 0.466 0.044 -0.020 49 1 0.999

273.15 253.15 373.15 50.00 450.00 0.543 0.050 0.005 59 5 0.897

0.093890 85.5588 -48.2382 12.2476 -1.6815 289.00 289.00 530.72 4.90 58.80 0.758 0.094 0.058 86 -2 0.939

0.095581 130.3507 -59.5821 26.2163 323.15 273.15 368.15 49.03 1176.80 0.769 0.070 0.057 36 0 0.990

14

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997

Table 3 (Continued) Esters (Continued) diethyl nonyl methyl 2,2-bis(phenyldiethyl dipropyl dinonyl dibutyl 2-methyl-2- (Z)-9-octa- methyl)propane- butane-1,4- butane-1,4- butane-1,4- 1,2-dibenzene4-methylpropenoate decenoate 1,3-dioate dioate dioate dioate dicarboxylate 1,3-dioxolan-2-one c0 b0/MPa b1/MPa‚K-1 b2/MPa‚K-2 T0/K Tmin/K Tmax/K Pmin/MPa Pmax/MPa RMSD/kg‚m-3 RMSDr/% bias/kg‚m-3 Np ( sw

0.093482 124.1357 -73.4228 13.7277 292.37 292.37 473.43 5.00 98.20 0.461 0.055 -0.019 77 1 1.102

0.096785 107.1134 -79.1092 -27.3425 368.15 273.15 368.15 49.03 980.67 0.388 0.041 -0.009 21 -5 0.949

0.103806 180.8024 -31.3735

0.057476 81.6161 -62.4077

0.073591 115.1185 -72.1588

368.15 273.15 368.15 49.03 490.33 1.225 0.106 0.066 12 2 1.060

295.65 295.65 347.15 5.00 49.10 0.429 0.042 -0.025 18 -4 1.037

288.15 288.15 347.95 5.00 49.10 0.858 0.085 0.083 22 8 0.981

0.495408 376.2686 -82.6642 8.5461 298.15 298.15 573.15 10.00 60.00 0.275 0.031 -0.029 72 -6 1.183

0.091695 140.4724 -75.1749 -14.5783 323.15 273.15 368.15 49.03 1176.80 0.929 0.080 0.036 34 2 1.058

0.092963 181.5743 298.15 298.15 298.15 50.00 200.00 0.095 0.008 0.001 4 -2 0.861

a The low limit of pressure ranges is 0.1 MPa or a saturation pressure (whichever is higher) for all fits; P min is the lowest pressure in a particular set of compressed-liquid density data retained for the correlation.

Table 6) are also significantly higher (0.5%) compared to other alkanones. In the case of 2-octanone two available data sets are mutually inconsistent. A more precise data set by Apaev et al. [78-apa/ker] (lower RMSD and the experimental uncertainty about 0.1% in density declared by the authors) was, however, retained, taking into account that the values from Atoyan’s laboratory were rejected for most of the other alkanones. The values of isothermal compressibility calculated from the fit are also reasonable, yielding an average deviation from literature values (see Table 5) of -5.7%, while those calculated from a tentative fit of data by Atoyan and Mamedov [75-ato/mam] showed an average deviation -8.5% with a maximum at 273.15 K (-14.1%). The data sets available for cyclohexanone are in good mutual agreement. It is, however, worth mentioning that the values retained in the evaluation were not direct experimental ones (Table 2). The isothermal compressibility calculated from the fit differs from the value obtained from literature data (Table 5) by -6.6%. Recently, Malhotra and Woolf [92-mal/woo] proposed generalized formulas for the parameters C and B of the Tait equation to calculate the volume ratio of liquid alkanones derived on the basis of their data for 2-propanone and 2-butanone [91-mal/woo, 92-mal/woo] in the reduced temperature range 0.54 e T/Tc e 0.62. The formulas proved to be successful also for 3-pentanone [93mal/pri]. In Table 6 the values of relative density, Frel ) F(T,P)/F(T,Pref) calculated from the fits in Table 3 are compared with those calculated from the generalized relations of Malhotra and Woolf. The deviations {Frel(Table 3) - Frel[92-mal/woo]}/Frel[92-mal/woo] observed for 2-propanone and 2-butanone are either within or close to the experimental error. Larger deviations for 2-butanone are found in the temperature range that exceeds the experimental range of Malhotra’s data [92-mal/woo]. Since the generalized formulas were derived from data measured for the first two members only of the homologous series (2propanone, 2-butanone) in a limited temperature range, the comparison presented in Table 6 for other alkanones is the comparison with the values obtained by an extensive extrapolation (in the sense of extrapolation beyond both the temperature range and particularly the range within the homologous series). Therefore, the significance of this comparison is, taking also into account the fact that one experimental data set only was available for some alkanones (see Table 2), rather low. However, the predic-

tions using the Malhotra and Woolf generalized equations agree with the existing experimental data within about 0.5% (on average) and similar uncertainty might be expected for other members of the alkanone homologous series. Aldehydes (Alkanals and Benzaldehyde). Data for members of the homologous series of aldehydes are very scarce. The analysis of literature data shows that values reported by Chaudhuri et al. [68-cha/sta] are likely to be systematically higher (by 10 kg·m-3 in density) since they show large positive deviations from both the repeated measurements performed in the extended temperature range in the same laboratory for butanal [71-run/sta] and the values for 3-methylbutanal reported by Mamedov et al. [75-mam/gus]. Therefore the data from [68-cha/sta] were not retained in the fits for these two alkanals. However, to provide an internally consistent set of the parameters of eq 1 for all data reported in the paper [68cha/sta] the additional correlations, where only values from this source were retained, were performed yielding the following results. Butanal: c0 ) 0.099 158, b0 ) 81.6468 MPa, Tmin ) Tmax ) 302.04 K, Pmax ) 138.00 MPa, RMSD ) 0.226 kg·m-3, RMSDr ) 0.027%, bias ) 0.023 kg·m-3, Np ) 10, ( ) 2. 3-Methylbutanal: c0 ) 0.077 919, b0 ) 51.0029 MPa, Tmin ) Tmax ) 300.37 K, Pmax ) 138.00 MPa, RMSD ) 1.081 kg·m-3, RMSDr ) 0.131%, bias ) 0.148 kg·m-3, Np ) 10, ( ) 2. Carboxylic Acids. The situation is similar to that for aldehydes. Except for methanoic acid, one data set only was found for each carboxylic acid. Two sets for methanoic acid, generated using the reported parameters of the Tait equation ([63-and], [71-kor]), were correlated together. Low deviations of the fit (Table 3) and apparent agreement of the two sets (Table 4) are rather artificial, since values for two isotherms, close each other, were correlated. The large absolute value of the parameter b1, which is, however, qualitatively correct being negative, indicates that the temperature dependence of density at elevated pressures might be incorrect and thus any extrapolation in temperature using the final fit is not advisable. The fits of data reported by Korpela [71-kor] for other acids (ethanoic, propanoic, 2-methylpropanoic) are recorrelations of the values generated using Tait parameters reported in the original paper for each temperature separately. The characteristic deviations of these fits (RMSD, RMSDr, bias) should not be, therefore, regarded as criteria of the quality

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997 15 Table 4. Statistical Characteristics of Individual Data Sets for the Fits in Table 3: Temperature and Pressure Ranges Taken into the Correlations, Tmin, Tmax, Pmin, and Pmax, Absolute, RMSD, and Relative, RMSDr, Root Mean Square Deviations, Biases, bias, Number of Data Points, Np, (, and Origin of the Reference Density Values Used in the Correlations, RDa ref 13-bri 31-bri 57-wal/ric 68-ski/cus 69-bra/fre 92-saf/mad

Tmin/K

Tmax/K

Np

(

RDa

-3.223 -1.144 -9.168

85 26 0 11 7 22

-75 4 0 -7 -5 -12

o e o o o (o)

1.072 0.183

-8.309 0.224

2 40

-2 6

o o

2,4-Dimethyl-3-oxapentane (Diisopropyl Ether) 106.8 511.3 3.161 0.363 0.5 8.0 0.179 0.025

0.134 0.051

7 45

1 3

o o

Pmin/MPa

303.15

348.15

49.1

303.15

303.15

100.0

68-ski/cus 92-saf/mad-1

294.30

374.50

70-sch/eck 96-gov/let

303.15 288.15

323.15 328.15

94-sen

298.15

328.15

4.9

5.1

Pmax/MPa

RMSD/kg‚m-3

3-Oxapentane (Diethyl Ether) 4.884 1176.9 1.118 400.0

4.213 1.541 13.994

4-Oxaheptane (Di-n-propyl Ether) 8.482 98.1 1.361

5-Oxanonane (Di-n-butyl Ether) 203.7 0.233

RMSDr/%

bias/kg‚m-3

0.560 0.123

-4.411 0.183

0.477 0.184 1.910

0.029

0.020

90

-2

o

-0.284 0.051

2 78

0 6

o o

-0.095

113

-13

o

49-bri 92-saf/mad

298.15 296.64

298.15 456.82

49.0 4.9

6-Oxaundecane (Di-n-pentyl Ether) 98.1 1.070 0.129 98.1 1.437 0.190

93-saf/oso

293.00

553.00

19.6

8-Oxapentadecane (Di-n-heptyl Ether) 98.1 1.793 0.228

94-sen 96-gov/let

298.15 288.15

328.15 328.15

3,3-Dimethyl-2-oxabutane (Methyl tert-Butyl Ether) 5.4 207.7 0.915 0.113 0.5 8.0 0.297 0.040

0.077 0.008

89 45

-11 1

o o

94-sen

298.15

328.15

4,4-Dimethyl-3-oxapentane (Ethyl tert-Butyl Ether) 5.6 207.2 0.483 0.062

0.015

90

0

o

328.15 328.15

3,3-Dimethyl-2-oxapentane (Methyl tert-Pentyl Ether) 5.6 203.8 0.341 0.042 0.5 8.0 0.140 0.018

-0.040 0.046

90 45

-16 23

o o

-1.841 0.028

12 90

-12 10

e o

0.013

90

8

o

94-sen 96-gov/let

298.15 288.15

78-sha/bai 94-sen

298.15

328.15

2,5-Dioxahexane (Ethylene Glycol Dimethyl Ether) 1.859 0.216 5.6 204.8 0.225 0.025

94-sen

298.15

328.15

2,5,8-Trioxanonane (Diethylene Glycol Dimethyl Ether) 5.1 202.8 0.173 0.018

298.15

348.15

4,7,10-Trioxatridecane (Diethylene Glycol Dipropyl Ether) 2.2 35.9 0.392 0.045

-0.114

22

-6

e

293.15

2,5,8,11,14-Pentaoxapentadecane (Tetraethylene Glycol Dimethyl Ether) 293.15 2.0 10.0 0.007 0.001 -0.001

5

-1

o

81-sha/abd 90-sve/sid 92-saf/gus 68-ski/cus 70-kus/tas

291.70

365.00

298.15

353.15

4-Oxa-1,6-heptadiene (Diallyl Ether) 98.1 1.680 0.230

0.140

38

6

o

Methoxybenzene (Methyl Phenyl Ether) 4.194 0.403 39.2 196.1 0.158 0.015

-3.711 0.000

3 20

-3 2

o o

Tetrahydrofuran (Oxolane) 517.0 2.554 6.825 101.3 1.248 10.0 0.011 8.0 0.108

0.254 0.727 0.132 0.001 0.012

-0.202 -6.825 -1.248 -0.002 0.025

7 1 1 5 45

-1 -1 -1 -1 19

o o o o o

Tetrahydropyran (Oxane) 8.0 0.094

0.011

-0.009

45

-5

o

1.241 0.097

0.118 0.009

0.338 0.010

0 2 45

0 0 3

o o o

2.385

0.213

0.001

185

49

o

Dibenzofuran 25.5 1.080

0.103

0.037

38

-2

o

0.880 0.183 0.738

-7.528 -1.569 -6.248

0.305

-2.471

28 1 1 0 0 7

-28 -1 -1 0 0 -7

o o o o o o

4.9

70-sch/eck 71-ham/smi 83-nak/miy 87-hol/goe 96-gov/let

303.15

323.15

212.3

298.15 293.15 288.15

298.15 293.15 328.15

101.3 2.0 0.5

96-gov/let

288.15

328.15

0.5

1,4-Dioxane 66-kor/kos 68-pea/str 96-gov/let

298.15 288.15

298.15 328.15

25.0 0.5

50.0 8.0

78-fig/szw

209.00

257.00

11.0

897.0

Furan

84-nas/siv 13-bri 51-new/wea 56-stu 57-wal/ric 66-win/powb 67-ada/lai

391.55

563.15

0.5

2-Propanone (Dimethyl Ketone) 7.784 1.569 6.248 2.558

16

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997

Table 4 (Continued) ref 76-ato/mam 77-gup/han 80-rae/fin 87-hol/goe-1 87-nhu/bha 91-mal/woo 91-pap/zia 92-ego/gru

Tmin/K

293.15 293.15 278.15 298.15

RMSDr/%

bias/kg‚m-3

Np

(

RDa

2-Propanone (Dimethyl Ketone) 7.201 2.203 15.986 10.0 0.160 10.0 0.115 392.3 0.267 33.8 0.349 1.295

0.837 0.283 1.799 0.020 0.014 0.031 0.043 0.157

-3.856 2.188 -13.019 0.142 0.100 0.083 -0.309 -1.054

16 8 17 5 5 105 9 5

-14 8 -17 5 5 25 -9 -5

(o) e e o o o o o

2-Butanone (Methyl Ethyl Ketone) 2.848 12.678 162.1 2.533 3.288 282.5 0.300

0.313 1.649 0.324 0.391 0.034

-2.820 8.745 -0.177 -2.028 0.040

6 243 28 15 137

-6 67 -4 -5 7

o (o) (o) o o

2-Pentanone (Methyl n-Propyl Ketone) 78.6 0.279 0.033

-0.054

18

-2

o

0.781 0.036

-5.871 0.087

27 128

-27 36

o o

2-Hexanone (Methyl n-Butyl Ketone) 156.9 0.990 0.125

-0.132

53

3

o

295.55

4-Methyl-2-pentanone (Methyl Isobutyl Ketone) 245.2 484.8 0.802 0.085

0.029

13

-3

o

403.00

10.0

4-Heptanone (Di-n-propyl Ketone) 160.0 1.102 0.129

-0.012

71

17

o

2-Octanone (Methyl n-Hexyl Ketone) 2.207 0.263 78.6 0.550 0.067

-1.004 -0.070

18 25

-14 -7

Tmax/K

293.15 293.15 323.15 298.15

Pmin/MPa

2.0 2.0 2.5 2.0

63-and 74-ato/mam 76-ato/bag 77-lam/hun 92-mal/woo

373.15

473.15

60.8

278.15

338.15

2.3

77-apa/ker

273.00

315.66

5.0

82-ato/mam 93-mal/pri

278.15

338.15

2.5

79-ato

293.15

393.15

9.8

63-and 91-ato

295.55 273.00

Pmax/MPa

RMSD/kg‚m-3

3-Pentanone (Diethyl Ketone) 6.740 389.8 0.307

75-ato/mam 78-apa/ker

273.15

374.31

5.0

69-bra/fre

298.15

298.15

50.0

Cyclopentanone 400.0 5.847

0.565

-0.318

8

0

o

Cyclohexanone 266.1 0.261 220.0 0.709

0.025 0.072

-0.231 -0.027

3 93

-3 11

o o

Ethanal (Acetaldehyde) 138.0 0.158

0.019

0.001

10

-2

o

0.016

-0.002

10

0

o

0.069

-0.075

0 25

0 -5

o o

2-Methylpropanal (Isobutyraldehyde) 138.0 0.258 0.031

-0.033

10

0

o

0.075

0.005

24

-6

o

3-Methylbutanal (Isovaleraldehyde) 6.168 0.754 50.1 0.343 0.044

6.162 -0.015

3 16

3 -4

o o

63-and 82-wis/wue

296.45 253.20

296.45 303.40

158.7 10.0

68-cha/sta

295.15

295.15

13.9

68-cha/sta

296.65

296.65

13.9

Propanal (Propionaldehyde) 138.0 0.130

(o) (o)

Butanal (Butyraldehyde) 68-cha/sta 71-run/sta

303.15

333.15

35.6

68-cha/sta

301.37

301.37

13.9

75-mam/gus

248.15

374.15

5.0

276.6

0.592

Pentanal (Valeraldehyde) 50.1 0.586

68-cha/sta 75-mam/gus

284.95

362.35

5.0

68-cha/sta

295.21

295.21

13.9

Heptanal (Enanthaldehyde) 138.0 0.073

0.009

-0.007

10

-2

o

Octanal (Caprylic Aldehyde) 138.0 0.098

0.012

0.005

10

0

o

68-cha/sta

293.87

293.87

13.9

68-cha/sta

295.21

295.21

13.9

138.0

Benzaldehyde 0.180

0.017

0.032

10

-2

o

0.006 0.002

0.008 -0.001

2 4

0 2

o o

63-and 71-kor

295.55 298.15

295.55 298.15

76.5 50.7

Methanoic Acid (Formic Acid) 107.5 0.070 202.7 0.028

71-kor

298.15

328.15

50.7

Ethanoic Acid (Acetic Acid) 253.3 0.098

0.009

0.000

12

2

o

71-kor

298.15

328.15

50.7

Propanoic Acid (Propionic Acid) 253.3 0.091

0.009

0.003

15

3

o

2-Methylpropanoic Acid (Isobutyric Acid) 50.7 253.3 0.272 0.027

0.004

15

-1

o

1.0

Octanoic Acid (Caprylic Acid) 9.0 0.068

0.008

0.006

30

4

o

1.0

Decanoic Acid (Capric Acid) 9.0 0.059

0.007

-0.001

30

0

o

71-kor

298.15

328.15

92-ban/gar

343.15

373.15

92-ban/gar

343.15

373.15

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997 17 Table 4 (Continued) ref

Tmin/K

Tmax/K

Pmin/MPa

Pmax/MPa

RMSD/kg‚m-3

RMSDr/%

92-ban/gar

343.15

373.15

1.0

Dodecanoic Acid (Lauric Acid) 9.0 0.054

0.006

92-ban/gar

353.15

373.15

1.0

Tetradecanoic Acid (Myristic Acid) 9.0 0.054

bias/kg‚m-3

RDa

Np

(

0.000

30

-2

o

0.006

0.001

25

1

o

0.005

0.000

25

1

o

30

0

o

-3 0 -4 -5 4

o o o o o

92-ban/gar

353.15

373.15

1.0

Hexadecanoic Acid (Palmitic Acid) 9.0 0.043

78-kum/iwa

253.15

313.15

19.7

Methyl Ethanoate (Methyl Acetate) 156.8 0.356

0.035

-0.003

Ethyl Ethanoate (Ethyl Acetate) 1.540

0.157

-1.402

0.832 0.167 0.050

-7.150 -0.781 0.100

3 0 4 17 32

1-Methylethyl Ethanoate (Isopropyl Acetate) 5.0 49.1 0.625 0.071

-0.088

18

0

o

0.084

32

0

oc

Propyl Propanoate (n-Propyl Propionate) 50.0 1.884 0.215

0.118

30

-6

o

3-Methylbutyl Propanoate (Isopentyl Propionate) 5.0 50.1 0.794 0.102

-0.031

32

-2

o

49-bri 63-and 70-sch/eck 75-gus/kad 79-kum/iwa

300.06 253.15

343.15 313.15

75-gus/kad

297.17

367.20

32-bri

273.15

1,2,3-Propanetriyl Triethanoate (Glyceryl Triacetate; Triacetin) 368.15 49.0 1176.8 1.314 0.102

78-gus/kli

300.00

400.00

76-gus/kli 92-mus/gus 92-mus/gus-1 32-bri 91-gus/kul 91-gus/kul-1 94-mus/tag 88-wal/lam 90-mus/gan-1

298.15

423.15

5.0 19.7

5.0

49.1 156.8

7.710 1.480 0.473

408.85

Methyl Hexanoate (Methyl Caproate) 4.9 58.8 0.660

0.078

0.020

33

-1

o

289.00

530.72

Nonyl Hexanoate (n-Nonyl Caproate) 4.9 58.8 0.758

0.094

0.058

86

-2

o

273.15

1,2,3-Propanetriyl Trihexanoate (Glyceryl Trihexanoate; Tricaproin) 368.15 49.0 1176.8 0.769 0.070

0.057

36

0

oc

294.99

294.36 296.71 300.48 253.15 298.15

343.41

2-Methylpropyl 2-Hydroxypropanoate (Isobutyl Lactate) 4.9 98.1 0.554 0.055

0.079

29

5

o

371.82

Pentyl 2-Hydroxypropanoate (n-Pentyl Lactate) 4.9 98.1 0.920 0.095

0.089

37

-3

o

440.59

Methyl Benzenecarboxylate (Methyl Benzoate) 5.0 58.9 0.466 0.044

-0.020

49

1

o

373.15

2-Ethylhexyl Benzenecarboxylate (2-Ethylhexyl Benzoate) 50.0 450.0 0.543 0.050

0.005

59

5

o

498.15

Methyl 2-Hydroxybenzenecarboxylate (Methyl Salicylate) 10.0 60.0 0.372 0.034

0.035

54

8

o

-0.019

71

-1

o

90-mus/gan-1

298.15

573.15

Pentyl 2-Hydroxybenzenecarboxylate (n-Pentyl Salicylate) 10.0 60.0 0.484 0.049

90-mus/gan-1

298.15

573.15

Hexyl 2-Hydroxybenzenecarboxylate (n-Hexyl Salicylate) 10.0 60.0 0.213 0.028

-0.023

72

-6

o

-0.008

61

-9

o o

87-gus/bai

289.34

349.29

Methyl 2-Methyl-2-propenoate (Methyl Methacrylate) 5.0 98.1 0.430 0.045

89-gus/bai

292.37

473.43

Nonyl 2-Methyl-2-propenoate (n-Nonyl Methacrylate) 5.0 98.2 0.461 0.055

-0.019

77

1

Methyl (Z)-9-Octadecenoate (Methyl Oleate) 49.0 980.7 0.388 0.041

32-bri

273.15

368.15

-0.009

21

-5

oc

32-bri

273.15

Diethyl 2,2-Bis(phenylmethyl)propane-1,3-dioate (Diethyl Dibenzylmalonate) 368.15 49.0 490.3 1.225 0.106 0.066

12

2

oc

90-mus/gan-3

295.65

347.15

Diethyl Butane-1,4-dioate (Diethyl Succinate) 5.0 49.1 0.429 0.042

-0.025

18

-4

o

90-mus/gan-2

288.15

347.95

Dipropyl Butane-1,4-dioate (Di-n-propyl Succinate) 5.0 49.1 0.858 0.085

0.083

22

8

o

Dinonyl Butane-1,4-dioate (Di-n-nonyl Succinate) 10.0 60.0 0.275 0.031

-0.029

72

-6

o

91-mus/gan

298.15

573.15

32-bri

273.15

368.15

Dibutyl Benzene-1,2-dicarboxylate (Di-n-butyl Phthalate) 49.0 1176.8 0.929 0.080

0.036

34

2

92-uos/kit

298.15

298.15

4-Methyl-1,3-dioxolan-2-one (Propylene Carbonate) 50.0 200.0 0.095 0.008

0.001

4

-2

oc o

a o, (o), from the same source as the compressed-liquid density data, available for a part of the temperature range only, respectively; e, from the smoothing equation (see Appendix I). b All three sets (see Table 2). c Relative volumes V(T,P)/V(T ) 273.15 K, P ) 0.1 MPa) presented in 32-bri were recalculated to V(T,P)/V(T,P ) 0.1 MPa), T > 273.15 K, using both F(T ) 273.15 K, P ) 0.1 MPa) given in the paper and V(T ) 368.15 K, P ) 0.1 MPa)/V(T ) 273.15 K, P ) 0.1 MPa) obtained by extrapolation of values for the isotherm T ) 368.15 K using the Tait equation.

18

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997

Table 5. Comparison of Values of Isothermal Compressibility, βT ) (1/G)(DG/DP)T, at P ) 0.1 MPa Calculated from the Fits in Table 3 (Eq 1) with Literature Data βT/GPa-1 T/K

eq 1a

lit.

δβT/%b

ref

2.110 2.082 2.269

3-Oxapentane -3.8 -2.5 -6.1

[72-dri/wil],c [83-hal/gun]d [82-bro/lop]e [72-dri/wil],c [83-hal/gun]d

1.76 ( 0.07

1.484 1.442

4-Oxaheptane 18.6 22.1

[72-dri/wil],c [85-oba/ood]d [83-kim/tre],f [92-saf/mad-1],g [96-zab/ruz]h

298.15

1.209 ( 0.004

1.223

5-Oxanonane -1.1

[72-dri/wil],c [85-oba/ood]d

298.15

0.93 ( 0.02

1.080

6-Oxaundecane -13.9

[72-dri/wil],c [85-oba/ood]d

298.15 313.15

1.782 (0.012 2.083 ( 0.015

4,4-Dimethyl-3-oxapentane 1.771 0.9 1.990 4.7

298.15

0.817 ( 0.002

303.15 308.15 313.15

0.848 ( 0.002 0.881 ( 0.002 0.916 ( 0.002

293.15 298.15

0.957 ( 0.002 1.010 ( 0.006

303.15 308.15

303.15

2.03 ( 0.03

308.15

2.13 ( 0.03

298.15

[95-mie/osw]e [95-mie/osw]e

0.823 0.814 0.853 0.877 0.911

2,5,8-Trioxanonane -0.7 0.3 -0.6 0.4 0.5

1.06 ( 0.01 1.12 ( 0.02

0.933 0.992 0.859 0.979 0.846 1.016 1.057

Tetrahydrofuran 2.6 1.8 17.6 3.2 19.4 4.3 6.0

[71-des/bha],f i, [96-zab/ruz]h [89-ram/kud],f i, [96-zab/ruz]h [89-ram/kud],f [96-gov/let],g,j [96-zab/ruz]h [79-kiy/dar],f i, [96-zab/ruz]h [79-kiy/dar],f [96-gov/let],g,j [96-zab/ruz]h [49-wei],f i, [96-zab/ruz]h [71-des/bha],f, i, [96-zab/ruz]h

298.15

0.99 ( 0.02

0.994

Tetrahydropyran -0.4

[91-spa/lep]e

293.15

0.75 ( 0.02

298.15

0.79 ( 0.02

303.15

0.82 ( 0.02

308.15

0.86 ( 0.03

0.701 0.601 0.738 0.744 0.627 0.637 0.768 0.650 0.797 0.669

1,4-Dioxane 7.0 24.8 7.0 6.2 26.0 24.0 6.8 26.2 7.9 28.6

[44-sch],f [92-sak],g [96-zab/ruz]h [44-sch],f [96-gov/let],g,k [96-zab/ruz]h [71-des/bha]e [90-aic/cos],f [92-sak],g [96-zab/ruz]h [90-aic/cos],f [96-gov/let],g,j [96-zab/ruz]h [90-aic/cos],f [96-gov/let],g,k [96-zab/ruz]h [49-wei],f [92-sak],g [96-zab/ruz]h [49-wei],f [96-gov/let],g,k [96-zab/ruz]h [71-des/bha],f [92-sak],g [96-zab/ruz]h [71-des/bha],f [96-gov/let],g,k [96-zab/ruz]h

293.15

1.234 ( 0.004

298.15

1.293 ( 0.004

308.15 313.15

1.419 ( 0.004 1.485 ( 0.004

318.15 323.15

1.553 ( 0.004 1.623 ( 0.005

1.269 1.271 1.324 1.286 1.398 1.561 1.536 1.523 1.657

2-Propanone -2.8 -2.9 -2.3 0.5 1.5 -4.9 -3.3 2.0 -2.0

[78-ric]e [71-ric/rog]e [78-ric]e [71-des/bha]e [71-des/bha]e [29-fre/hub]e [71-ric/rog]e [71-des/bha]e [29-fre/hub],f [91-trc],g [96-zab/ruz]h

283.15 293.15

1.032 ( 0.002 1.120 ( 0.002

298.15 303.15 313.15 333.15 353.15

1.167 ( 0.002 1.216 ( 0.003 1.322 ( 0.003 1.566 ( 0.005 1.87 ( 0.01

1.022 1.116 1.117 1.188 1.214 1.328 1.593 1.940

2-Butanone 1.0 0.4 0.3 -1.8 0.2 -0.5 -1.6 -3.6

[49-lag/mcm],f [91-trc],g [96-zab/ruz]h [78-ric]e [76-ato/bag],f [91-trc],g [96-zab/ruz]h [78-ric]e [78-red/nai],f [91-trc],g [96-zab/ruz]h [76-ato/bag],f [91-trc],g [96-zab/ruz]h [76-ato/bag],f [91-trc],g [96-zab/ruz]h [76-ato/bag],f [91-trc],g [96-zab/ruz]h

293.15 298.15 303.15 313.15

0.97 ( 0.02 1.02 ( 0.02 1.07 ( 0.02 1.20 ( 0.02

1.051 1.092 1.141 1.234

2-Pentanone -7.7 -6.6 -6.2 -2.7

[78-ric]e [78-ric]e [78-sre/nai],f [91-trc],g [96-zab/ruz]h [78-sre/nai],f [91-trc],g [96-zab/ruz]h

293.00 303.15 313.00 313.15 333.00

1.002 ( 0.003 1.083 ( 0.004 1.169 ( 0.004 1.171 ( 0.004 1.373 ( 0.006

1.018 1.114 1.190 1.209 1.405

3-Pentanone -1.6 -2.7 -1.8 -3.1 -2.3

[82-ato/mam],f [93-mal/pri],g [96-zab/ruz]h [76-red/nai],f [93-mal/pri],g [96-zab/ruz]h [82-ato/mam],f [93-mal/pri],g [96-zab/ruz]h [76-red/nai],f [93-mal/pri],g [96-zab/ruz]h [82-ato/mam],f [93-mal/pri],g [96-zab/ruz]h

[82-tre/hal],f [94-sen],g [96-zab/ruz]h [93-ami/pha],f [94-sen],g [96-zab/ruz]h [93-ami/pha],f [94-sen],g [96-zab/ruz]h [93-ami/pha],f [94-sen],g [96-zab/ruz]h [93-ami/pha],f [94-sen],g [96-zab/ruz]h

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997 19 Table 5 (Continued) βT/GPa-1 T/K

eq

1a

lit.

δβT/%b

ref

2-Hexanone -19.8 -17.8 -17.3 -14.2 -11.8 -10.8 -11.8

[78-ric]e [79-ato],f [91-trc],g [96-zab/ruz]h [78-ric]e [79-ato],f [91-trc],g [96-zab/ruz]h [79-ato],f [91-trc],g [96-zab/ruz]h [79-ato],f [91-trc],g [96-zab/ruz]h [79-ato],f [91-trc],g [96-zab/ruz]h [91-ato],f,g [96-zab/ruz]h [91-ato],f,g [96-zab/ruz]h [91-ato],f,g [96-zab/ruz]h

293.15

0.80 ( 0.02

298.15 313.15 333.15 353.15 373.15

0.84 ( 0.02 0.97 ( 0.02 1.17 ( 0.03 1.40 ( 0.03 1.66 ( 0.04

0.995 0.973 1.014 1.131 1.326 1.570 1.882

303.00 323.00 343.00

0.87 ( 0.02 1.04 ( 0.02 1.24 ( 0.03

1.020 1.177 1.366

4-Heptanone -14.7 -11.6 -9.2

273.15 293.15

0.73 ( 0.02 0.84 ( 0.02

298.15 313.15 333.15 353.15 373.15

0.87 ( 0.02 0.97 ( 0.02 1.14 ( 0.03 1.36 ( 0.04 1.64 ( 0.06

0.797 0.885 0.914 0.899 1.053 1.219 1.421 1.673

2-Octanone -8.4 -5.2 -8.1 -3.2 -7.9 -6.5 -4.3 -2.0

303.15

0.67 ( 0.01

0.717

Cyclohexanone -6.6

[76-rao/nai],f [82-wis/wue],g [96-zab/ruz]h

295.21

0.61 ( 0.01

0.573

Benzaldehyde 6.5

l

0.617 0.613 0.627 0.620

Methanoic Acid -2.6 -2.0 3.2 4.4

0.954 0.918 1.045 1.003 1.112 1.118 1.069 1.158 1.072

Ethanoic Acid -3.7 0.1 -2.6 1.5 -1.9 -2.4 2.1 -2.5 5.3

[64-lut/sol]e [65-for/moo],f [83-hal/gun],g [96-zab/ruz]h [64-lut/sol]e [83-goo/whi],f [83-hal/gun],g [96-zab/ruz]h [71-ric/rog]e [64-lut/sol]e [83-goo/whi],f [83-hal/gun],g [96-zab/ruz]h [64-lut/sol]e [83-goo/whi],f [83-hal/gun],g [96-zab/ruz]h

0.939 0.930 1.043 1.022 1.164 1.124

Propanoic Acid -1.5 -0.5 -1.3 0.7 -1.5 2.0

[64-lut/sol]e [83-goo/whi],f [83-hal/gun],g [96-zab/ruz]h [64-lut/sol]e [83-goo/whi],f [83-hal/gun],g [96-zab/ruz]h [64-lut/sol]e [83-goo/whi],f [83-hal/gun],g [96-zab/ruz]h

[75-ato/mam],f [91-trc],g [96-zab/ruz]h [78-ric]e [75-ato/mam],f [91-trc],g [96-zab/ruz]h [78-ric]e [75-ato/mam],f [91-trc],g [96-zab/ruz]h [75-ato/mam],f [91-trc],g [96-zab/ruz]h [75-ato/mam],f [91-trc],g [96-zab/ruz]h [75-ato/mam],f [91-trc],g [96-zab/ruz]h

[64-lut/sol]e [83-goo/whi],f [84-trc],g [96-zab/ruz]h [64-lut/sol]e [83-goo/whi],f [84-trc],g [96-zab/ruz]h

295.55

0.601 ( 0.001

298.15

0.647 ( 0.002

298.15

0.919 ( 0.003

313.15

1.018 ( 0.003

323.15

1.091 ( 0.004

328.15

1.129 ( 0.004

298.15

0.925 ( 0.002

313.15

1.029 ( 0.003

328.15

1.146 ( 0.004

298.15 299.15 303.15 308.15 313.15

1.16 ( 0.01 1.17 ( 0.01 1.22 ( 0.01 1.29 ( 0.02 1.36 ( 0.02

1.158 1.174 1.212 1.273 1.337

Methyl Ethanoate 0.2 -0.4 0.6 1.3 1.7

273.15 293.15 298.15 323.15

0.97 ( 0.01 1.16 ( 0.02 1.20 ( 0.02 1.47 ( 0.02

0.980 1.133 1.206 1.480

Ethyl Ethanoate -1.0 2.4 -0.5 -0.7

298.15

0.56 ( 0.01m

Methyl Benzenecarboxylate 0.618 -9.4

[93-ami/rai],f [91-gar/mir],g [96-zab/ruz]h

298.15

0.512 ( 0.003

4-Methyl-1,3-dioxolan-2-one 0.518 -1.2 0.480 6.6

[86-bot/bre]e,n [86-bot/bre]e,o

[93-ami/pha],f [78-kum/iwa],g [96-zab/ruz]h [53-par/bak],f [78-kum/iwa],g [96-zab/ruz]h [93-ami/pha],f [78-kum/iwa],g [96-zab/ruz]h [93-ami/pha],f [78-kum/iwa],g [96-zab/ruz]h [93-ami/pha],f [78-kum/iwa],g [96-zab/ruz]h [71-ric/rog]e [71-ric/rog]e [93-ami/rai],f [69-trc],g [96-zab/ruz]h [71-ric/rog]e

a Uncertainty is estimated as (2s, where s is a standard deviation derived from a covariance matrix of each fit. b [β (eq 1) - β (lit.)]100/ T T βT(lit.). c Thermal pressure coefficient, γV ) (∂P/∂T)V. d Thermal expansivity, RP ) (1/V)(∂V/∂T)P. e Isothermal compressibility, βT ) -(1/ f g h i V)(∂V/∂P)T. Speed of sound. Density and thermal expansivity. Isobaric heat capacity. Density and thermal expansivity were obtained from smoothed density data from 83-ing/gro, 87-hol/goe, and 89-ram/kud. j RP taken from the text in 96-gov/let. k RP calculated from the smoothing equation presented in Appendix II. l Literature value was obtained by linear interpolation between βT(T ) 293.15 K) ) 0.566 GPa-1 and βT(T ) 299.75 K) ) 0.587 GPa-1 evaluated from speeds of sound from 44-sch and 53-par/bak, smoothed densities from 75amb/con, and heat capacities from 96-zab/ruz. m Extrapolated. n Evaluated from piezometric measurements. o Evaluated from densitometric measurements.

20

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997

Table 6. Comparison of Relative Densities, Grel ) G(T,P)/G(T,Pref), (See Eq 1), of Alkanones Calculated from the Fits in Table 3 with the Generalized Tait Equation of Malhotra and Woolf [92-mal/woo] alkanone

T rangea/K

Tr rangeb

Pmaxa/MPa

RMSDr/%

biasrc/%

max. devc/%

2-propanone 2-butanone 2-pentanone 3-pentanone 2-hexanone 4-methyl-2-pentanone 4-heptanone 2-octanone

278-323 278-353 273-313 278-338 293-393 296 273-403 273-373

0.55-0.64 0.52-0.66 0.49-0.56 0.50-0.60 0.50-0.67 0.51 0.45-0.67 0.43-0.59

309 280 78 390 160 480 160 80

0.070 0.074 0.156 0.165 0.531 0.308 0.384 0.615

-0.012 0.019 -0.108 -0.124 -0.444 0.297 0.163 0.490

-0.177 -0.225 -0.362 -0.305 -1.195 0.388 0.840 1.715

a The temperature and pressure ranges are up to T max (Table 3) or normal boiling temperature, whichever is lower, and Pmax (Table 3), respectively. The relative density values used in a comparison were generated in 5 K and Pmax/10 increments. b Critical temperatures were taken from 95-pul/gud; that of 4-methyl-2-pentanone (575.5 ( 0.5 K) was from 93-cda. c {Frel(Table 3) - Frel[92-mal/woo]}100/Frel[92mal/woo].

Table A1. Parameters, ai, of Functions A1 and A2 Used for the Fits in Table 3, Critical Densities, Gc, Critical Temperatures, Tc, Temperature Ranges of Validity, Tmin and Tmax, Absolute, RMSD, and Relative, RMSDr, Root Mean Square Deviations, Biases, bias, Number of Data Points, Np, (, References to the Density Data, ref(G), and References to Saturated Vapor Pressure Data, ref(Pref) 3-oxapentane eq a0 a1 a2 a3 Fc/kg·m-3 a Tc/K Tmin/K Tmax/K RMSD/kg·m-3 RMSDr/% bias/kg·m-3 Np ( ref(F) ref(Pref)

2,5-dioxahexane

4,7,10-trioxatridecane

2-propanone

2-butanone

2-octanone

A1 1.877396 0.220896 0.621815

A1 -1.951904 9.590776 -5.635101

A2 1123.8823 -69.3648 -3.15008

264.724 466.74 293.15 370.00 0.035 0.005 0.000 8 0 83-hal/gun 83-mcg

332.554 536.00 288.00 333.00 0.605 0.070 0.000 9 -1 78-sha/bai

298.15 348.15 0.112 0.013 0.000 7 -1 81-sha/abd

A1 1.838053 0.582830 -0.100291 0.570410 277.895 508.10 178.50 508.10 0.107 0.025 0.000 35 1 91-trc

A1 2.132989 0.934622 -1.953535 1.940789 270.064 536.78 193.15 536.78 0.135 0.026 -0.005 36 2 91-trc 83-mcg

A1 5.598593 -12.662290 15.459716 -5.297409 258.000 632.70 273.15 433.15 0.024 0.003 0.001 18 -4 91-trc

a Given with three decimal points since critical densities were calculated from rounded values of critical molar volumes recorded in the database.

of data. Low scatter of the generated P-F-T values used in correlations results also in low values of standard deviations of values of isothermal compressibility calculated from the fits. The agreement with the values from the literature is quite satisfactory (the deviations below 6% for ethanoic acid and below 2% for propanoic acid; see Table 5). Esters. One experimental data set only was available for all but one ester. In the case of ethyl ethanoate two data sets ([79-kum/iwa], [75-gus/kad]) are in acceptable agreement at lower temperatures; the values reported by Guseinov and Kadzarov [75-gus/kad] for higher temperatures (where no original reference densities were available) are not, however, consistent with smoothed saturatedliquid densities from 69-trc, and thus the temperature range of the fit was limited up to 343 K to avoid an inflection point on the B(T) curve. The agreement of calculated values of isothermal compressibility at atmospheric pressure with data from the literature is satisfactory (see Table 5). An obvious typographical error was found in the data table presented for propyl propanoate by Guseinov and Klimova [78-gus/kli]; the value of F(T ) 300 K, P ) 0.1 MPa) should be 873.8 kg·m-3. With this value of the reference density all values along the isotherm 300 K become consistent with other reported data. Similarly, the reference density F(T ) 311.48 K, P ) 0.1 MPa) ) 932.4 kg·m-3 reported for methyl 2-methyl-2-propenoate by Guseinov et al. [87-gus/bai] is erroneous; the correct value 923.4 kg·m-3, deduced from a comparison with the smoothed value at atmospheric pressure (see Table A2 in Appendix II), was used in the correlations. Values at lower pressures (up to 10 MPa) for 3-methylbutyl propanoate [76-

gus/kli], 2-methylpropyl 2-hydroxypropanoate [91-gus/kul], and pentyl 2-hydroxypropanoate [91-gus/kul-1] were mostly rejected due to large deviations compared to other isobars. Unusually high uncertainty ((5%) is declared by the authors [88-wal/lam] for measurements of density of 2-ethylhexyl benzenecarboxylate; fitting their data showed, however, low scatter and good consistency, contrary to the declared accuracy of measurements. The value reported by Mustafaev et al. [90-mus/gan-1] for pentyl 2-hydroxybenzenecarboxylate at T ) 298.15 K and P ) 60 MPa was rejected, being obviously erroneous (typographical error, correct value should be probably 1086.1 kg·m-3). With the original value it was impossible to find reasonable values of adjustable parameters b c and b b for the entire data set. Data measured for 4-methyl-1,3-dioxolan-2-one (propylene carbonate) were correlated by 92-uos/kit using the Tait equation; our parameters c0 and b0 differ slightly from their values since the weighted least squares fit using experimental uncertainties declared by Uosaki and Kitaura was performed. Acknowledgment A substantial part of this work was done during the stay of I. C. in the laboratory of Prof. I. Nagata and Prof. T. Yamada, Department of Chemical Engineering, Kanazawa University, Japan. Computer and other facilities provided by the Japanese Ministry of Education (Monbusho) are acknowledged. Thanks are also expressed to Prof. K. N. Marsh and Dr. R. C. Wilhoit (TRC) for extracting speed of sound data from the TRC Source Database.

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997 21 Table A2. Parameters ai of Smoothing Functions A1 or A2 Fitted to Original Reference Density Values (G(T,Pref)), Critical Densities,a Gc, Critical Temperatures,a Tc, Temperature Ranges of Validity, Tmin and Tmax, and RMSD of the Fits eq A1

a0 5.58970

a1 -9.79084

a2

a3

Fc/kg‚m-3

Tc/K

4-Oxaheptane 261.991 530.60

7.29440

Tmin/K

Tmax/K

RMSD/kg‚m-3

ref

294.30

374.50

0.173

92-saf/mad-1

288.15

328.15

0.035

96-gov/let

293.15

328.15

0.039

94-sen

296.64

456.82

1.085

92-saf/mad

293.00

553.00

0.252

93-saf/oso

293.15

328.15

0.111

94-sen

293.15

328.15

0.165

94-sen

2,4-Dimethyl-3-oxapentane A2 A1

1072.556 3.86694

-153.742

-5.02658

11.667 5-Oxanonane 260.461 580.00

4.11614

6-Oxaundecane A2

1057.381

-96.713

1.388 8-Oxapentadecane

A2 A1

1045.472 5.11100

-83.989

-9.01518

-0.061 6.95032

3,3-Dimethyl-2-oxabutane 277.200 497.10 4,4-Dimethyl-3-oxapentane

A2

1099.724

-137.703

5.184

A2

1025.918

-78.203

-2.932

3,3-Dimethyl-2-oxapentane

A1

2.38730

-2.12662

2.26726

2,5-Dioxahexane 332.554 536.00

A1

3.12088

-3.47744

3.22672

2,5,8-Trioxanonane 318.706 625.30

293.15

328.15

0.035

94-sen

293.15

328.15

0.049

94-sen

293.15

328.15

0.031

94-sen

293.15

293.15

2,5,8,11,14-Pentaoxapentadecane A2

1011.110

90-sve/sid

4-Oxa-1,6-heptadiene A2 A1 A1 A1 A1

1008.412 0.28525 2.83393 10.04322 9.28035

-104.677 3.87691 -2.57687

-20.40679

-17.86459

2.626

291.70

365.00

0.842

92-saf/gus

-1.58385

Methoxybenzene 335.839 645.60

298.15

353.15

0.071

70-kus/tas

2.41398

Tetrahydrofuran 321.906 540.10

278.15

318.15

0.185

b, i

13.18624

Tetrahydropyran 327.505 572.20

288.15

328.15

0.327

96-gov/let

11.34313

1,4-Dioxane 370.195 587.00

288.15

328.15

0.300

96-gov/let

209.00

257.00

1.414

78-fig/szwc

Furan A2

1464.660

-294.417

42.262

A2

1720.181

-259.830

32.168

Dibenzofuran -1.953

391.55

563.15

0.009

84-nas/siv

233.15

373.15

0.059

91-trcd,i

A1

2.69374

-2.45770

2.54994

2-Pentanone 286.159 561.08

A1

4.17653

-4.95315

4.06914

3-Pentanone 256.000 560.60

278.15

338.15

0.003

93-mal/pri

4.59059

2-Hexanone 267.095 587.00

293.15

393.15

0.019

79-ato

273.00

403.00

0.648

91-ato

298.15

298.15

253.20

303.40

0.135

82-wis/wue

303.15

333.15

0.290

71-run/sta

248.15

374.15

1.714

75-mam/gus

284.95

362.35

0.000e

75-mam/gus

298.15

298.15

A1

4.13574

-5.57604

4-Heptanone A2

1080.148

A2

943.000

-88.701

-0.353 Cyclopentanone

A1

0.87043

2.31845

A1

2.58929

0.22314

Cyclohexanone 314.567 653.00

-0.47564

Butanal 259.378

524.00

69-bra/fre

Pentanal A2

560.204

A2

913.687

224.899

-48.533 3-Methylbutanal

11.1330

-17.428 Methanoic Acid

A2

1213.6

71-kor

A1

0.50162

7.48628

-11.10569

6.09003

Ethanoic Acid 351.185 592.71

293.15

490.00

0.063

83-hal/gunf,i

A1

-1.08282

13.12210

-18.34957

9.33221

Propanoic Acid 333.691 612.00

288.15

490.00

0.040

83-hal/gung,i

298.15

328.15

0.047

71-kor

2-Methylpropanoic Acid A2

1245.170

-101.337

22

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997

Table A2 (Continued) eq

a0

a1

a2

a3

Fc/kg‚m-3

Tc/K

Tmin/K

Tmax/K

RMSD/kg‚m-3

ref

343.15

373.15

0.060

92-ban/gar

343.15

373.15

0.081

92-ban/gar

343.15

373.15

0.054

92-ban/gar

353.15

373.15

0.078

92-ban/gar

Octanoic Acid A2

1120.486

-67.062

-1.762

A2

1028.591

-23.715

-7.286

Decanoic Acid Dodecanoic Acid A2

1016.266

-21.787

-7.285 Tetradecanoic Acid

A2

1114.020

-76.200 Hexadecanoic Acid

A2 A1 A1

1109.558 1.47530 1.69043

353.15

373.15

0.081

92-ban/gar

1.35621

Methyl Ethanoate 324.910 506.80

253.15

313.15

0.408

78-kum/iwa

2.64150

Ethyl Ethanoate 3.52368 308.064 523.20

273.15

473.15

0.106

69-trci

297.17

367.20

0.000e

75-gus/kad

300.00

400.00

1.677

78-gus/kli

298.15

423.15

0.157

76-gus/kli

294.99

408.85

0.536

92-mus/gus

289.00

549.37

0.235

92-mus/gus-1

2-Methylpropyl 2-Hydroxypropanoate 294.36

371.42

0.078

91-gus/kul

296.71

371.82

1.279

91-gus/kul-1

300.48

440.59

0.292

94-mus/tag

253.15

373.15

0.000h

88-wal/lam

Methyl 2-Hydroxybenzenecarboxylate 336.615 763.00 298.15

498.15

0.178

90-mus/gan-1

573.15

0.195

90-mus/gan-1

573.15

0.050

90-mus/gan-1

289.34

349.29

0.162

87-gus/bai

292.37

473.43

1.192

89-gus/bai

295.65

347.15

0.000e

90-mus/gan-3

288.15

347.95

0.147

90-mus/gan-2

298.15

573.15

0.109

91-mus/gan

-75.740

-4.70476

1-Methylethyl Ethanoate A2 A1

1298.373 4.99964

-162.582

-8.04117

6.2022 Propyl Propanoate 294.076 571.00

6.23552

3-Methylbutyl Propanoate A2

1100.050

-66.234

-4.333 Methyl Hexanoate

A2

1170.294

-101.267

0.376 Nonyl Hexanoate

A2

1248.402

-211.291

36.084

A2

959.494

38.991

-10.133

-3.277

Pentyl 2-Hydroxypropanoate A2

1178.221

-67.054

A2

1265.729

-38.365

Methyl Benzenecarboxylate -7.623 2-Ethylhexyl Benzenecarboxylate A2 A1

1192.191 3.91754

-77.500

-4.77123

4.28255

A2

1288.069

-83.477

-0.009

Pentyl 2-Hydroxybenzenecarboxylate 298.15

A2

983.795

-60.237

-0.229

Hexyl 2-Hydroxybenzenecarboxylate 298.15 Methyl 2-Methyl-2-propenoate

A2

1101.229

0.316

-18.439 Nonyl 2-Methyl-2-propenoate

A2

1182.666

-117.059

4.949 Diethyl Butane-1,4-dioate

A2

1382.302

-126.452

3.541 Dipropyl Butane-1,4-dioate

A2

806.562

196.733

-43.665 Dinonyl Butane-1,4-dioate

A2

1075.179

-55.159

-0.080

a Taken from 93-cda. b [83-ing/gro], [87-hol/goe], and [89-ram/kud]. c The data from 78-fig/szw differ significantly from recommended values published in 85-trc. d Reference 77-apa/ker presents two values of density at atmospheric pressure only, but compressed-liquid density data are inconsistent with the reference line from 91-trc and thus only original reference values were used for the fit in Table 3. e Polynomial interpolation. f Data from 71-kor are lower by 0.5 kg‚m-3 in average. g Data from 71-kor are lower by 0.2 kg‚m-3 in average. h The fit of all seven data points reported yielded a straight line. i Densities from the source other than that of compressed-liquid data.

Appendix I Equations Used for F(T,Pref(T)) ) F(T) in Fits by Eq 1 and References to Saturated Vapor Pressure Data. In those cases where the reference density values F(T,Pref(T)) (see eq 1) either were not available in original papers or the values at atmospheric pressure were reported for different temperatures than compressed-liquid density data, the two following functions were used for the data sets denoted by letter “e” or “(o)” in the last column of Table 4 to calculate reference density values

F(T/K)/kg·m-3 ) Fc{1 + a0(1 - Tr)1/3 + a1(1 - Tr)2/3 + a2(1 - Tr) + a3(1 - Tr)4/3}

Tr ) T/Tc (A1)

F(T/K)/kg·m-3 ) a0 + a1(T/100) + a2(T/100)2 + a3(T/100)3 (A2) The values of adjustable parameters ai obtained by fitting to available data using a weighted least squares method are recorded in Table A1 along with some characteristics of the fits. Equation A1 was preferably used in those cases

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997 23 where respective critical parameters (Fc, Tc) were available. The references to the saturated vapor pressure data, Pref(T), used in eq 1 are also given in Table A1 in those cases when the upper temperature limit, Tmax, of the corresponding fit in Table 3 is above the normal boiling temperature. It should be pointed out that the fits in Table A1 do not represent a critical evaluation of density data at atmospheric pressure or at saturation (except for the fits of recommended density values taken from the TRC Thermodynamic Tables) which is beyond the scope of the present review. On the other hand, reliable and highquality experimental data were selected where possible (see, e.g., 3-oxapentane). The values of reference density, F(T,Pref), Pref ) 0.101 325 MPa in most cases, reported for the same samples in original literature sources of compressed-liquid density data, were exclusively employed for the fits in Table 3 for the substances which are not listed in Table A1 except for 2,5-dioxaheptane [78-sha/bai] and 4,7,10-trioxatridecane [81-sha/abd] where original reference density values, F(T,Pref ) 0.101 325 MPa), were smoothed (Table A1) before the use for fits by eq 1 for respective compressed-liquid density data sets since in those two cases the experimental densities at atmospheric pressure and those for the compressed liquid were reported for different temperatures. Appendix II Parameters of Smoothing Functions for Original Reference Density Data. Table A2 summarizes values of adjustable parameters ai of functions A1 and A2 (see Appendix I) fitted mostly to the values of experimental densities at atmospheric pressure reported for the same samples as compressed-liquid density data retained in correlations by the Tait equation (Tables 3 and 4). The functions were not, unlike the equations summarized in Table A1, employed in smoothing the compressed-liquid density data and are presented as auxiliary information here, which may be useful particularly for less common substances. The functions enable us to calculate smoothed reference density values to be used in evaluation of compressed-liquid densities from eq 1. The fits in Table A2 are not the fits of critically selected experimental data. Only in several cases are the parameters ai obtained using either recommended density values taken from the TRC Thermodynamic Tables or data from other reliable sources presented. Original reference density values for substances not listed in Tables A1 and A2 were not reported in original sources; i.e., relative quantities as relative density, F(T,P)/ F(T,Pref), volume ratio, V(T,P)/V(T,Pref), or compression, {1 - V(T,P)/V(T,Pref)}, only were presented by researchers. Literature Cited 13-bri

Bridgman, P. W. Thermodynamic Properties of Twelve Liquids between 20 degrees and 80 degrees and up to 12000 kg/cm2. Proc. Am. Acad. Arts Sci. 1913, 49, 3-114.

29-fre/hub

Freyer, E. B.; Hubbard, J. C.; Andrews, D. H. Sonic Studies of the Physical Properties of Liquids. I. The Sonic Interferometer. The Velocity of Sound in Some Organic Liquids and Their Compressibilities. J. Am. Chem. Soc. 1929, 51, 759-770.

31-bri

Bridgman, P. W. The Volume of Eighteen Liquids as a Function of Pressure and Temperature. Proc. Am. Acad. Arts Sci. 1931, 66, 185-233.

32-bri

Bridgman, P. W. Volume-Temperature-Pressure Relations for Several Non-Volatile Liquids. Proc. Am. Acad. Arts Sci. 1932, 67, 1-27.

44-sch

Schaaffs, W. Investigations on the Velocity of Sound and Constitution. I. The Velocity of Sound in Organic Liquids. Z. Phys. Chem. (Leipzig) 1944, 194, 28.

49-bri

Bridgman, P. W. Further Rough Compressions to 40,000 kg/cm2, Especially Certain Liquids. Proc. Am. Acad. Arts Sci. 1949, 77, 129-146.

49-lag/mcm

Lagemann, R. T.; McMillan, D. R.; Woolf, W. E. Temperature Variation of Ultrasonic Velocity in Liquids. J. Chem. Phys. 1949, 17, 369-373.

49-wei

Weissler, A. Ultrasonic Investigation of Molecular Properties of Liquids. IV. Cyclic Compounds. J. Am. Chem. Soc. 1949, 71, 419-421.

51-new/wea

Newitt, D. M.; Weale, K. E. Pressure-VolumeTemperature Relations in Liquids and Liquid Mixtures. Part II. The Compression Isotherms of Some Organic Liquids up to 1000 Atmospheres, and the Compressions of Some Aqueous and Non-aqueous Binary Liquid Mixtures. J. Chem. Soc. 1951, 30923098.

53-par/bak

Parthasarathy, S.; Bakhshi, N. N. Sound Velocity Measurements in Organic Liquids. Indian J. Phys. 1953, 27, 73.

56-stu

Stutchbury, J. E. Compressions of Organic Liquids and their Mixtures with Water. Aust. J. Chem. 1956, 9, 536-540.

57-wal/ric

Walsh, J. M.; Rice, H. M. Dynamic Compression of Liquids from Measurements on Strong Shock Waves. J. Chem. Phys. 1957, 26, 815-823.

63-and

Andersson, G. R. A Study of the Pressure Dependence of the Partial Specific Volume of Macromolecules in Solution by Compression Measurements in the Range 1-8000 atm. Ark. Kemi 1963, 20, 513571.

64-lut/sol

Lutskii, A. E.; Solonko, V. N. Hydrogen Bond and Compressibility of Liquids. II. Monocarboxylic Acids of the Fatty Acid Series. Zh. Fiz. Khim. 1964, 38, 1421-1428 (in Russian).

65-for/moo

Fort, R. J.; Moore, W. R. Adiabatic Compressibilities of Binary Liquid Mixtures. Trans. Faraday Soc. 1965, 61, 2102-2111.

66-kor/kos

Korpela, J.; Koskikallio, J. Compressibilities of Dioxan - Water Mixtures at 25 °C. Suom. Kemistil. B 1966, 39, 165-168.

66-win/pow

Winnick, J.; Powers, J. E. The P-V-X Behavior of the Liquid System Acetone-Carbon Disulfide at Elevated Pressures. AIChE J. 1966, 12, 460-465.

67-ada/lai

Adams, W. A.; Laidler K. J. Effects of Pressure and Temperature on the Structure of Liquid Acetone. Can. J. Chem. 1967, 45, 123-139.

68-cha/sta

Chaudhuri, P. M.; Stager, R. A.; Mathur, G. P. Properties of Aliphatic and Aromatic Aldehydes under High Pressure. Compressibility and Viscosity Determination. J. Chem. Eng. Data 1968, 13, 9-11.

68-pea/str

Pearce, P. J.; Strauss, W. Effect of Pressure on the Density of Dioxan and Dioxan-Water Mixtures at 25 °C. Aust. J. Chem. 1968, 21, 1213-1219.

68-ski/cus

Skinner, J. F.; Cussler, E. L.; Fuoss, R. M. Pressure Dependence of Dielectric Constant and Density of Liquids. J. Phys. Chem. 1968, 72, 1057-1064.

69-bra/fre

Brazier, D. W.; Freeman, G. R. The Effect of Pressure on the Density, Dielectric Constant, and Viscosity of Several Hydrocarbons and Other Organic Liquids. Can. J. Chem. 1969, 47, 893-899.

69-trc

TRC Table 23-2-1-(1.1320)-d, C-H-O. n-Alkyl Ethanoates (Acetates), C3 to C22. TRC Thermodynamic Tables - Non-Hydrocarbons, Thermodynamics Research Center, College Station, TX, 1969, 55505551.

70-kus/tas

Kuss, E.; Taslimi, M. p,V,T-Messungen an zwanzig organischen Flussigkeiten (p,V,T Measurement of Twenty Organic Liquids). Chem.-Ing.-Tech. 1970, 42, 1073-1081.

70-sch/eck

Schornack, L. G.; Eckert, C. A. The Effect of Pressure on the Density and Dielectric Constant of Polar Solvents. J. Phys. Chem. 1970, 74, 30143020.

71-des/bha

Deshpande, D. D.; Bhatgadde, L. G. Heat Capacities at Constant Volume, Free Volumes, and Rotational Freedom in Some Liquids. Aust. J. Chem. 1971, 24, 1817-1822.

71-ham/smi

Hamann, S. D.; Smith, F. The Effect of Pressure on the Volumes and Excess Volumes of Aqueous Solutions of Organic Liquids. Aust. J. Chem. 1971, 24, 2431-2438.

24

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997

71-kor

Korpela, J. The Densities and Compression Isotherms of Formic Acid-, Acetic Acid-, Propionic Acid-, and Isobutyric Acid-Water Mixtures. Acta Chem. Scand. 1971, 25, 2852-2864.

71-ric/rog

Richard, A. J.; Rogers, K. S. The Isothermal Compressibility of Organic Liquids by Ultracentrifugation. Correlation with Surface Tension. Can. J. Chem. 1971, 49, 3956-3959.

71-run/sta

Rungta, K. K.; Stager, R. A.; Mathur, G. P. Properties of n-Butyraldehyde under High Pressure. Viscosity and Compressibility Determination. Can. J. Chem. Eng. 1971, 49, 886-888.

72-dri/wil

Driver, G. R.; Williamson, A. G. Thermal Pressure Coefficients of Di-n-alkyl Ethers. J. Chem. Eng. Data 1972, 17, 65-66.

73-erm/bai

74-ato/mam

Ermakov, G. V.; Baidakov, V. G.; Skripov, V. P. Density of Overheated Diethyl Ether and the Boundary of Stability of Liquid State. Zh. Fiz. Khim. 1973, 47, 1026-1027 (in Russian). Deposited in VINITI No. 5144-72 since November 29, 1972. Atoyan, V. A.; Mamedov, I. A. Apparatus for Determination of Density of Liquids and Gases at High Temperatures and Pressures Using a Weighing Method. Izv. Akad. Nauk Azerb. SSR, Ser. Fiz. Tekn. Mat. Nauk 1974, 17 (10), 119-123 (in Russian).

Propyl Ketone in a Wide Range of Temperatures and Pressures. Ukr. Fiz. Zh. (Ukr. Ed.) 1977, 22, 408-412 (in Russian). 77-gup/han

Gupta, A. C.; Hanks, R. W. Liquid Phase PVT Data for Binary Mixtures of Toluene with Nitroethane and Acetone, and Benzene with Acetonitrile, Nitromethane, and Ethanol. Thermochim. Acta 1977, 21, 143-152.

77-gus/sad

Guseinov, K. D.; Sadykhova, A. A. Observation of p-V-T Dependence of Ethyl Ester of Caproic Acid. Zh. Fiz. Khim. 1977, 51, 2406-2406 (in Russian). Deposited in VINITI No. 951-77 since March 14, 1977.

77-lam/hun

Lamb, J. A.; Hunt, A. F. Volumes of Mixing of Metyl Ethyl Ketone with Water at Elevated Pressures. Chem. Eng. J. (Lausanne) 1977, 14, 73-76.

78-apa/ker

Apaev, T. A.; Kerimov, A. M.; Dzhanakhmedov, N. Kh. Observation of P-V-T Dependence of Methyl Hexyl Ketone in a Wide Interval of Temperatures and Pressures. Inzh.-Fiz. Zh. 1978, 35 (1), 166-167 (in Russian).

78-fig/szw

Figuiere, P.; Szwarc, H. P-V-T Relations for Liquid and Crystalline Furan from 210 to 260 K, up to 1000 MPa. High Temp.- High Pressures 1978, 10, 473-476.

75-amb/con

Ambrose, D.; Connett, J. E.; Green, J. H. S.; Hales, J. L.; Head, A. J.; Martin, J. F. Thermodynamic Properties of Organic Oxygen Compounds. 42. Physical and Thermodynamic Properties of Benzaldehyde. J. Chem. Thermodyn. 1975, 7, 1143-1157.

78-gus/asl

Guseinov, K. D.; Aslanov, G. A. Observation of p-V-T Dependence and Dynamic Viscosity of Hexyl Formiate. Zh. Fiz. Khim. 1978, 52, 483-483 (in Russian). Deposited in VINITI No. 2487-77 since July 23, 1977.

75-ato/mam

Atoyan, V. A.; Mamedov, I. A. Observation of Dependence of Velocity and Absorption of Sound, Viscosity, and Density of Methyl Hexyl Ketone on Temperature and Pressure. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1975, 18 (5), 74-78 (in Russian).

78-gus/asl-1

Guseinov, K. D.; Aslanov, G. A. Observation of p-V-T Dependence of Octyl Formiate. Zh. Fiz. Khim. 1978, 52, 807-807 (in Russian). Deposited in VINITI No. 3856-77 since October 5, 1977.

78-gus/kli

75-gus/abd

Guseinov, K. D.; Abdullaeva, R. I. Observation of Thermal Conductivity and Density of Isoamyl Valerate at High Parameters of State. Zh. Fiz. Khim. 1975, 49, 3002-3002 (in Russian). Deposited in VINITI No. 2378-75 since August 4, 1975.

Guseinov, K. D.; Klimova, T. F. Experimental Observation of P-v-T Dependence of Propyl Propionate at High State Parameters. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1978, 21 (2), 67-70 (in Russian).

78-kum/iwa

Kumagai, A.; Iwasaki, H. Pressure-Volume-Temperature Relationships of Several Polar Liquids. J. Chem. Eng. Data 1978, 23, 193-195.

78-red/nai

Reddy, K. S.; Naidu, P. R. Isentropic Compressibilities of Mixtures of an Alcohol + Methylethylketone. J. Chem. Thermodyn. 1978, 10, 201-202.

78-ric

Richard, A. J. Isothermal Compressibility of Methyl Ketones and the Density Coefficient of Polarizability for Several Compounds by Ultracentrifugation. J. Phys. Chem. 1978, 82, 1265-1268.

78-sha/bai

Sharipov, K.; Bairamova, N. N. Experimental Observation of P-v-T and Ps-Ts Dependencies of Ethylene Glycol Dimethyl Ether. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1978, 21 (8), 62-64 (in Russian).

78-sre/nai

Guseinov, K. D.; Klimova, T. F. Experimental Observation of Density of Isoamyl Propionate in a Wide Interval of Temperatures and Pressures. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1976, 19 (8), 5858 (in Russian).

Sreenivasulu, M.; Naidu, P. R. Isentropic Compressibilities of n-Butylamine + Methyl Ethyl Ketone, + Methyl n-Propyl Ketone, and + Diethyl Ketone at 303.15 and 313.15 K. J. Chem. Thermodyn. 1978, 10, 1019-1022.

79-ato

Guseinov, K. D.; Sadykhova, A. A. Observation of p-V-T Dependence of Amyl Ester of Caproic Acid. Zh. Fiz. Khim. 1976, 50, 3000-3001 (in Russian). Deposited in VINITI No. 2766-76 since July 20, 1976.

Atoyan, V. A. Observation of Velocity and Coeffcient of Absorption of Sound in Methyl Butyl Ketone, its Density and Viscosity in Dependence on Temperature and Pressure. Zh. Fiz. Khim. 1979, 53, 27842789 (in Russian).

79-bas/erm

Bashkatov, N. V.; Ermakov, G. V. Experimental Device and Results of Measurements of P-V-T Properties of Overheated Liquid Acetone. Teplofiz. Vys. Temp. 1979, 17, 1115-1115 (in Russian). Deposited in VINITI No. 2134-79 since June 12, 1979.

79-kiy/dar

Kiyohara, O.; D’Arcy, P. J.; Benson, G. C. Ultrasonic Velocities, Compressibilities, and Heat Capacities of Water + Tetrahydrofuran Mixtures at 298.15 K. Can. J. Chem. 1979, 57, 1006-1010.

79-kum/iwa

Kumagai, A.; Iwasaki, H. Pressure-Volume-Temperature Relationships of CH3COOC2H5 and Generalized Tait Equation for Liquids at High Pressures. J. Chem. Eng. Data 1979, 24, 261-263.

80-rae/fin

Raetzsch, M.; Findeisen, R. PVT-Messungen an Flussigkeiten und Gasen mit einem Faltenbalgpiezometer (PVT-Measurements of Liquids and Gases

75-gus/kad

75-mam/gus

76-ato/bag

76-ato/mam

76-gus/kli

76-gus/sad

Guseinov, K. D.; Kadzarov, V. T. Experimental Observation of P-V-T Dependence of Isopropyl Acetate and Ethyl Acetate. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1975, 18 (1), 56-56 (in Russian). Mamedov, M. N.; Guseinov, K. D.; Kerimov, A. M. Experimental Observation of P-V-T Dependence of Liquid Aldehydes. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1975, 18 (6), 70-80 (in Russian). Atoyan, V. A.; Bagdasaryan, S. S.; Mamedov, I. A. Observation of Acoustic and Viscous Properties of Methyl Ethyl Ketone in a Wide Interval of Temperatures and Pressures. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1976, 19 (6), 65-68 (in Russian). Atoyan, V. A.; Mamedov, I. A. Observation of Acoustic and Viscous Properties of Dimethyl Ketone in a Wide Interval of Temperatures and Pressures. Zh. Fiz. Khim. 1976, 50, 2976-2978 (in Russian).

76-rao/nai

Rao, M. V. P.; Naidu, P. R. Excess Volumes and Isentropic Compressibilities of Binary Mixtures of Alcohol + Cyclohexanone. Part II. J. Chem. Thermodyn. 1976, 8, 96-98.

76-red/nai

Reddy, K. S.; Naidu, P. R. Isentropic Compressibilities of Mixtures of an Alcohol + Diethylketone. J. Chem. Thermodyn. 1976, 8, 1208-1210.

77-abd/gus

Abdullaeva, R. I.; Guseinov, K. D. Experimental Observation of Density of Butyl Valerate in a Wide Interval of Temperatures and Pressures. Zh. Fiz. Khim. 1977, 51, 1012-1012 (in Russian). Deposited in VINITI No. 4295-76 since December 14, 1976.

77-apa/ker

Apaev, T. A.; Kerimov, A. M.; Dzhanakhmedov, N. K. Observation of P-v-T Dependence of Methyl

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997 25 with a Bellows Piezometer). Z. Phys. Chem. (Leipzig) 1980, 261, 935-945 (in German). 81-sha/abd

Sharipov, K.; Abdullaev, F. G.; Akhundov, T. S. Density of Diethylene Glycol Dipropyl Ether in a Wide Interval of Pressures and Temperatures. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1981, 24 (1), 4446 (in Russian).

82-ato/mam

Atoyan, V. A.; Mamedov, I. A. A Study of Acoustic and Viscous Properties of Diethyl Ketone in the Interval of Temperature 293-473 K and Pressures up to 156.8 MPa. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1982, 25 (6), 45-48 (in Russian).

82-bro/lop

Brostow, W.; Lopez, D. M. M.; Maynadier, P. Isothermal Compressibility of Liquids: New Results on Temperature Dependence. Proc. 8th Symp. Thermophys. Prop., Vol 1: Thermophysical Properties of Liquids 1982, (1), 122-127.

82-tre/hal

Treszczanowicz, A. J.; Halpin, C. J.; Benson, G. C. Excess Volumes and Isentropic Compressibilities of 2,5,8-Trioxanonane-n-Heptane Mixtures. J. Chem. Eng. Data 1982, 27, 321-324.

82-wis/wue

Wisotzki, K. D.; Wuerflinger, A. PVT Data for Liquid and Solid Cyclohexane, Cyclohexanone and Cyclopentanol up to 3000 bar. J. Phys. Chem. Solids 1982, 43, 13-20.

Normal Alkanes (C5 - C16). Int. Data Ser., Sel. Data Mixtures, Ser. A 1987, No. 4, 263-268. 87-hol/goe-1

Holzapfel, K.; Goetze, G.; Demiriz, A. M.; Kohler, F. Volume and Isothermal Compressibility of Some Normal Alkanes (C5-C16) + 2,3-Dimethylbutane, + Methylcyclopentane, + Butylcyclohexane, + Benzene, + 2-Propanone, or + Tetrachloromethane. Int. Data Ser., Sel. Data Mixtures, Ser. A 1987, No. 1, 30-56.

87-nhu/bha

Nhu, N. V.; Bhat, S. N.; Kohler, F. Calculation of Isothermal Compressibilities of Mixtures. The Example Acetone + Chloroform. Ber. Bunsen-Ges. Phys. Chem. 1987, 91, 525-528.

88-wal/lam

Walker, N. A.; Lamb, D. M.; Adamy, S. T.; Jonas, J.; Dare-Edwards, M. P. Self-diffusion in the Compressed, Highly Viscous Liquid 2-Ethylhexyl Benzoate. J. Phys. Chem. 1988, 92, 3675-3679.

89-gus/bai

Guseinov, K. D.; Bairamov, N. M.; Aliev, A. E. P-V-T Dependence and Heat Capacity at Constant Pressure of Nonyl Ester of Methacrylic Acid. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1989, 32 (1), 50-52 (in Russian).

89-ram/kud

Ramkumar D. H. S.; Kudchadker, A. P. Mixture Properties of the Water + γ-Butyrolactone + Tetrahydrofuran System. 1. Densities of γ-Butyrolactone + Water at 303.15 - 343.15 K and of Tetrahydrofuran + γ-Butyrolactone at 278.15 - 298.15 K; Ultrasonic Velocities at 298.15 K for the Three Binary Systems Inclusive of Tetrahydrofuran + Water and the Ternary System Tetrahydrofuran + Water + γ-Butyrolactone. J. Chem. Eng. Data 1989, 34, 459-463.

90-aic/cos

Aicart, E.; Costas, M.; Junquera, E.; Tardajos, G. Ultrasonic Speeds and Isentropic Compressibilities of (1,4-Dioxane + n-Heptane or n-Decane or nTetradecane). J. Chem. Thermodyn. 1990, 22, 11531158.

90-mus/gan

Mustafaev, R. A.; Ganiev, D. K.; Raginov, R. S.; Bairamov, N. M.; Mamedov, M. B.; Gasanov, G. T. P-F-T Dependence of Methyl Ester of Salicylic Acid in a Wide Interval of State Parameters. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1990, 33 (10), 27-28 (in Russian).

90-mus/gan-1

Mustafaev, R. A.; Ganiev, D. K.; Ragimov, R. S. P-F-T Dependence of Esters of Salicylic Acid. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1990, 33 (6), 9596 (in Russian).

90-mus/gan-2

Mustafaev, R. A.; Ganiev, D. K.; Ragimov, R. S. P-F-T Dependence of Dipropyl Ester of Succinic Acid. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1990, 33 (2), 28-58 (in Russian).

90-mus/gan-3

Mustafaev, R. A.; Ganiev, D. K.; Ragimov, R. S. P-F-T Dependence of Diethyl Ester of Succinic Acid. Inzh.-Fiz. Zh. 1990, 59 (2), 259-261 (in Russian).

90-sve/sid

Svejda, P.; Siddiqi, M. A.; Hahn, G.; Christoph, N. Excess Volume, Isothermal Compressibility, and Excess Entalpy of Binary Liquid System 2,2,2Trifluoroethanol + 2,5,8,11,14-Pentaoxapentadecane. J. Chem. Eng. Data 1990, 35, 47-49.

83-goo/whi

Goodman, M. A.; Whittenburg, S. L. Sound Velocity in Simple Carboxylic Acids. J. Chem. Eng. Data 1983, 28, 350-351.

83-hal/gun

Hales, J. L.; Gundry, H. A.; Ellender, J. H. Liquid Densities from 288 to 490 K of Four Organic Oxygen Compounds. J. Chem. Thermodyn. 1983, 15, 211215.

83-ing/gro

Inglese, A.; Grolier, J.-P. E.; Wilhelm, E. Excess Volumes of Mixtures of Oxolane, Oxane, 1,3-Dioxolane, and 1,4-Dioxane with n-Alkanes at 298.15, 308.15, and 318.15 K. J. Chem. Eng. Data 1983, 28, 124-127.

83-kim/tre

Kimura, F.; Treszczanowicz, A. J.; Halpin, C. J.; Benson, G. C. Excess Volumes and Ultrasonic Speeds for (Di-n-propylether + n-Heptane). J. Chem. Thermodyn. 1983, 15, 503-510.

83-mcg

McGarry, J. Correlation and Prediction of the Vapor Pressures of Pure Liquids over Large Pressure Ranges. Ind. Eng. Chem., Process Des. Dev. 1983, 22, 313-332.

83-nak/miy

Nakagawa, M.; Miyamoto, Y.; Moriyoshi T. Compression of Aqueous Binary Mixtures Containing Alcohols and Cyclic Ethers at 298.15 K and 101.3 MPa. J. Chem. Thermodyn. 1983, 15, 15-21.

84-nas/siv

Nasir, P.; Sivaraman, A.; Kobayashi, R. The Molar Volume and Fugacity of Liquid Dibenzofuran at High Temperatures and High Pressures. J. Chem. Thermodyn. 1984, 16, 199-205.

84-trc

TRC Table 23-2-1-(1.1210)-d, C-H-O. Alkanoic Acids, C1 to C5. TRC Thermodynamic Tables - NonHydrocarbons, Thermodynamics Research Center, College Station, TX, 1984, 5450-5451.

85-oba/ood

Obama, M.; Oodera, Y.; Kohama, N.; Yanase, T.; Saito, Y.; Kusano, K. Densities, Molar Volumes, and Cubic Expansion Coefficients of 78 Aliphatic Ethers. J. Chem. Eng. Data 1985, 30, 1-5.

91-ato

Atoyan, V. A. Acoustic and Viscous Properties of Dipropyl Ketone in the Ranges 273-473 K and 0.1 - 156.8 MPa. Russ. J. Phys. Chem. (Engl. Transl. of Zh. Fiz. Khim.) 1991, 65, 100-104.

85-tek/cib

Teka´cˇ, V.; Cibulka, I.; Holub, R. PVT Properties of Liquids and Liquid Mixtures: A Review of the Experimental Methods and the Literature Data. Fluid Phase Equilib. 1985, 19, 33-149.

91-gar/mir

85-trc

TRC Table 23-2-1-(9.2152)-d, C-H-O. Alkyl Furans, C4 to C6. TRC Thermodynamic Tables - NonHydrocarbons, Thermodynamics Research Center, College Station, TX, 1985, 6360.

Garcia, B.; Miranda, M. J.; Leal, J. M.; Ortega, J.; Matos, J. S. Densities and Viscosities of Mixing for the Binary Systems of Methyl Benzoate with nNonane at Different Temperatures. Thermochim. Acta 1991, 186, 285-292.

91-gus/kul

Guseinov, K. D.; Kuliev E. M. Thermal Properties of Iso-Butyl Ester of Lactic Acid. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1991, 34 (5), 68-72 (in Russian).

91-gus/kul-1

Guseinov, K. D.; Kuliev, E. M. P-v-T Dependence of Amyl Ester of Lactic Acid. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1991, 34 (3), 38-68 (in Russian).

91-mal/woo

Malhotra, R.; Woolf, L. A. Thermodynamic Properties of Propanone (Acetone) at Temperatures from 278 K to 323 K and Pressures up to 400 MPa. J. Chem. Thermodyn. 1991, 23, 867-876.

91-mus/gan

Mustafaev, R. A.; Ganiev, D. K.; Bairamov, N. M.; Ragimov, R. S. Experimental Observation of P-F-T Dependence of Dinonyl Ester of Succinic Acid. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1991, 34 (5), 6667 (in Russian).

86-bot/bre

87-gus/bai

87-hol/goe

Bottomley, G. A.; Bremers, M. T. Electrolyte Molar Volumes at 273-373 K in Propylene Carbonate, N-Methylformamide, Formamide, and Methanol: Their Relation to Solvent Compressibility. Ion Association Constants in Acetonitrile at 298 K. Aust. J. Chem. 1986, 39, 1959-1981. Guseinov, K. D.; Bairamov, N. M.; Aliev, A. E. P-V-T Dependence of Methyl Ester of Methacrylate Acid. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1987, 30 (5), 85-87 (in Russian). Holzapfel, K.; Goetze, G.; Kohler F. Volume and Isothermal Compressibility of Oxolane + Some

26

Journal of Chemical and Engineering Data, Vol. 42, No. 1, 1997

91-pap/zia

Papaioannou, D.; Ziakas, D.; Panayiotou, C. Volumetric Properties of Binary Mixtures. 1. 2-Propanone + 2,2,4-Trimethylpentane and n-Heptane + Ethanol Mixtures. J. Chem. Eng. Data 1991, 36, 35-39.

91-spa/lep

Spaneda, A.; Lepori, L.; Matteoli, E. Volumes of Mixing of Ethers with Tetrachloromethane at 298.15 K. Fluid Phase Equilib. 1991, 69, 209-222.

91-trc

TRC Table 23-2-1-(1.2000)-d, C-H-O. 2-Alkanones. TRC Thermodynamic Tables - Non-Hydrocarbons, Thermodynamics Research Center, College Station, TX, 1991, 5870-5872.

92-ban/gar

Banipal, T. S.; Garg, S. K.; Ahluwalia, J. C. Densities of Some Higher Alkan-1-oic Acids at Temperatures from 343.15 K to 373.15 K and at Pressures up to 9 MPa. J. Chem. Thermodyn. 1992, 24, 729735.

92-ego/gru

Egorov, G. I.; Gruznov, E. L.; Kolker, A. M. p-V-x Properties of Mixture Water-Acetone at 298.15 K in the Interval from 1 to 600 bars. Zh. Fiz. Khim. 1992, 66, 1458-1465 (in Russian).

92-mal/woo

Malhotra, R.; Woolf, L. A. Thermodynamic Properties of Butan-2-one at Temperatures from 278 K to 338 K and Pressures from 0.1 MPa to 280 MPa; Prediction for Higher Ketones. J. Chem. Thermodyn. 1992, 24, 1207-1217.

92-mus/gus

Mustafaev, R. A.; Guseinov, M. A.; Abbasov, R. M. Experimental Observation of Density of Methyl Caproate at High Temperatures and Pressures. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1992, 35 (7), 7296 (in Russian).

92-mus/gus-1

Mustafaev, R. A.; Guseinov, M. A. Experimental Observation of Density of Nonyl Caproate in Dependence on Temperature and Pressure. Izv. Vyssh. Ucheb. Zaved., Neft Gaz 1992, 35 (8), 33-34 (in Russian).

92-saf/gus

Safarov, M. M.; Guseinov, K. D.; Madzhidov, K.; Asoev, R. Sh. Density of Liquid Diallyl Ether in a Wide Range of Pressures and Temperatures. Zh. Fiz. Khim. 1992, 66, 1697-1701 (in Russian).

93-cda

CDATA, Database of Physical and Transport Properties of Pure Fluids. Department of Physical Chemistry, Institute of Chemical Technology: Prague; FIZ CHEMIE GmbH: Berlin, 1993.

93-cib

Cibulka, I. Saturated Liquid densities of 1-Alkanols from C1 to C10 and n-Alkanes from C5 to C16: A Critical Evaluation of Experimental Data. Fluid Phase Equilib. 1993, 89, 1-18.

93-mal/pri

Malhotra, R.; Price, W. E.; Woolf, L. A. Thermodynamic Properties of Pentan-3-one at Temperatures from 278 K to 338 K and Pressures from 0.1 MPa to 380 MPa. J. Chem. Thermodyn. 1993, 25, 361366.

93-saf/oso

Safarov, M. M.; Osoev, R. Sh. Density of Diheptyl Ether in Liquid Phase. Inzh.-Fiz. Zh. 1993, 64 (4), 440 (in Russian).

94-cib/zik

Cibulka. I.; Zikova´, M. Liquid Densities at Elevated Pressure of 1-Alkanols from C1 to C10: A Critical Evaluation of Experimental Data. J. Chem. Eng. Data 1994, 39, 876-886.

94-mus/tag

Mustafaev, R. A.; Tagiev, S. I.; Bairamov, N. M.; Gabulov, D. M. Experimental Observation of Density of Methyl Benzoate in a Wide Interval of Temperatures and Pressures. Teplofiz. Vys. Temp. 1994, 32, 135-138 (in Russian).

94-sen

Senger, M. Bestimmung der P,V,T-Reinstoffdaten verschiedener aliphatischer Ether bei unterschiedlichen Temperaturen und Drucken bis 2000 bar (Determination of PVT Data of Various Pure Aliphatic Ethers at Different Temperatures and Pressures up to 2000 bar). Thesis, Heidelberg University, Germany, 1994, 97 pp (in German).

95-mie/osw

Mier, W.; Oswald, G.; Tusel-Langer, E.; Lichtenthaler, R. N. Excess Enthalpy HE of Binary Mixtures Containing Alkanes, Ethanol, and Ethyl-Tert. Butyl Ether (ETBE). Ber. Bunsen-Ges. Phys. Chem. 1995, 99, 1123-1130.

95-pul/gud

Pulliam, M. K.; Gude, M. T.; Teja, A. S. Critical Temperatures and Densities of n-Alkanones. J. Chem. Eng. Data 1995, 40, 455-458.

92-saf/mad

Safarov, M. M.; Madzhidov, Kh.; Asoev, R. Sh. Generalized Equation of State of Liquid Simple Ethers. Zh. Fiz. Khim. 1992, 66, 2595-2603 (in Russian).

96-cib/hne

Cibulka, I.; Hneˇdkovsky´, L. Liquid Densities at Elevated Pressure of n- Alkanes from C5 to C16: A Critical Evaluation of Experimental Data. J. Chem. Eng. Data 1996, 41, 657-668.

92-saf/mad-1

Safarov, M. M.; Madzhidov, Kh.; Asoev, R. Sh. P-F Dependencies of Dipropyl Ether in Wide Interval of Temperatures and Pressures. Teplofiz. Vys. Temp. 1992, 30, 190-192 (in Russian).

96-gov/let

92-sak

Sakurai, M. Partial Molar Volumes for 1,4-Dioxane + Water. J. Chem. Eng. Data 1992, 37, 492-496.

Govender, U. P.; Letcher, T. M.; Garg, S. K.; Ahluwalia, J. C. Effect of Temperature and Pressure on the Volumetric Properties of Branched and Cyclic Ethers. J. Chem. Eng. Data 1996, 41, 147150.

96-zab/ruz

92-uos/kit

Uosaki, Y.; Kitaura, S.; Moryioshi, T. Compressions of 4-methyl-1,3-dioxolan-2-one and some alkanols at presures up to 200 MPa and at the temperature 298.15 K. J. Chem. Thermodyn. 1992, 24, 559-560.

Za´bransky´, M.; Ru˚zˇicˇka, V.; Majer, V.; Domalski, E. S. Heat Capacities of Liquids. Review and Recommended Values. J. Phys. Chem. Ref. Data; Monograph No. 6, American Chemical Society: Washington, DC, 1996.

93-ami/pha

Aminabhavi, T. M.; Phayde, H. T. S.; Aralaguppi, M. I.; Khinnavar, R. S. Densities, Viscosities, and Speeds of Sound for Diethylene Glycol Dimethyl Ether + Methyl Acetate. J. Chem. Eng. Data 1993, 38, 540-541.

93-ami/rai

Aminabhavi, T. M.; Raikar, S. K.; Balundgi, R. H. Densities, Viscosities, Refractive Indices, and Speeds of Sound in Methyl Acetoacetate + Methyl Acetate, + Ethyl Acetate, + n-Butyl Acetate, + Methyl Benzoate, and + Ethyl Benzoate at 298.15, 303.15, and 308.15 K. J. Chem. Eng. Data 1993, 38, 441445.

Received for review June 10, 1996. Accepted October 9, 1996.X Provision of the 1-year assistant professor position at Kanazawa University by the Japanese Ministry of Education (Monbusho) is acknowledged as well as support from the Grant Agency of the Czech Republic within the Grant No. 203/94/0312.

JE960199O

X

Abstract published in Advance ACS Abstracts, November 15, 1996.