Synergistic Treatment of Mixed 1,4-Dioxane and Chlorinated Solvent

Oct 12, 2017 - Best management practices are ... Abstract | Full Text HTML | PDF w/ Links | Hi-Res PDF · Microbial Photoelectrotrophic Denitrification...
3 downloads 13 Views 967KB Size
Subscriber access provided by LAURENTIAN UNIV

Article

Synergistic Treatment of Mixed 1,4-Dioxane and Chlorinated Solvent Contaminations by Coupling Electrochemical Oxidation with Aerobic Biodegradation Jeramy R. Jasmann, Phillip B. Gedalanga, Thomas Borch, Shaily Mahendra, and Jens Blotevogel Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.7b03134 • Publication Date (Web): 12 Oct 2017 Downloaded from http://pubs.acs.org on October 13, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 28

Environmental Science & Technology

Synergistic Treatment of Mixed 1,4-Dioxane and Chlorinated Solvent Contaminations by Coupling Electrochemical Oxidation with Aerobic Biodegradation Jeramy R. JasmannA,†, Phillip B. GedalangaB, Thomas BorchA,C,D, Shaily MahendraB, Jens BlotevogelC,*

A

Department of Chemistry, Colorado State University, Fort Collins, Colorado, CO 80523, USA

B

Department of Civil and Environmental Engineering, University of California, Los Angeles, CA 90095, USA

C

Department of Civil and Environmental Engineering, Colorado State University, Fort Collins, CO 80523, USA

D

Department of Soil and Crop Sciences, Colorado State University, Fort Collins, CO 80523, USA



Current address: U.S. Geological Survey, National Research Program, Boulder, CO 80303, USA

TOC Art

1 ACS Paragon Plus Environment

Environmental Science & Technology

1

ABSTRACT

2

Biodegradation of the persistent groundwater contaminant 1,4-dioxane is often hindered

3

by the absence of dissolved oxygen and the co-occurrence of inhibiting chlorinated solvents.

4

Using flow-through electrolytic reactors equipped with Ti/IrO2-Ta2O5 mesh electrodes, we show

5

that combining electrochemical oxidation with aerobic biodegradation produces an over-additive

6

treatment effect for degrading 1,4-dioxane. In reactors bioaugmented by Pseudonocardia

7

dioxanivorans CB1190 with 3.0 V applied, 1,4-dioxane was oxidized 2.5 times faster than in

8

bioaugmented control reactors without an applied potential, and 12 times faster than by abiotic

9

electrolysis only. Quantitative polymerase chain reaction analyses of CB1190 abundance,

10

oxidation-reduction potential, and dissolved oxygen measurements indicated that microbial

11

growth was promoted by anodic oxygen-generating reactions. At a higher potential of 8.0 V,

12

however, the cell abundance near the anode was diminished, likely due to unfavorable pH and/or

13

redox conditions. When coupled to electrolysis, biodegradation of 1,4-dioxane was sustained

14

even in the presence of the common co-contaminant trichloroethene in the influent. Our findings

15

demonstrate that combining electrolytic treatment with aerobic biodegradation may be a

16

promising synergistic approach for the treatment of mixed contaminants.

17 18 19

INTRODUCTION

20

1,4-Dioxane, a widely used solvent stabilizer, is a persistent organic pollutant frequently

21

observed in groundwater impacted by chlorinated volatile organic compounds.1-3 Recent reports

22

of contaminated site data from across the United States highlight the high probability of co-

23

occurrence of 1,4-dioxane with vapor degreasers such as trichloroethene (TCE) and 1,1,1-

24

trichloroethane (1,1,1-TCA).3-5 1,4-Dioxane’s miscibility in water and low sorption affinity to

25

soil make it highly mobile in groundwater, frequently leading to large plume development.

26

While often at sub-mg/L concentrations in dilute groundwater plumes, 1,4-dioxane

27

concentrations can occur at tens or hundreds of mg/L in source zones and industrial

28

wastewater.3,6-8 1,4-dioxane is highly recalcitrant, and commonly applied remediation

29

technologies for chlorinated solvent co-contaminants, like sorption and air stripping, have been

30

ineffective for its removal. Advanced oxidation processes (AOPs) involving UV light can

31

produce highly reactive hydroxyl radicals (•OH) to mineralize 1,4-dioxane, 9-12 but the high cost 2 ACS Paragon Plus Environment

Page 2 of 28

Page 3 of 28

Environmental Science & Technology

32

typically limits their use to treatment of relatively small water volumes and ex situ treatment.

33

Thus, the development of more cost-effective treatment options is critically needed.

34

Recent laboratory studies have documented successful aerobic biodegradation of 1,4-

35

dioxane either co-metabolically13-16 or metabolically,16-18 and one study demonstrated microbially

36

driven Fenton-based degradation19 of 1,4-dioxane in a system alternating between aerobic and

37

anaerobic conditions. These studies indicate that bioremediation of 1,4-dioxane is generally

38

possible under suitable conditions. However, three factors may limit the site-specific

39

biodegradation potential for 1,4-dioxane: (1) lack of dissolved oxygen for aerobic microbial

40

respiration, (2) low activity of indigenous bacterial populations, and (3) inhibition of microbial

41

metabolism by chlorinated solvents.20-22 Currently, all pure culture isolates capable of 1,4-

42

dioxane biodegradation require O2 as the terminal electron acceptor.13-18 This constraint has been

43

prohibitive to natural attenuation approaches since 1,4-dioxane contamination often occurs in

44

anoxic water conditions. Recent investigations by Mahendra and coworkers20,22 revealed that

45

TCE, 1,1,1-TCA, and the abiotic transformation products 1,1-dichloroethene (1,1-DCE) and cis-

46

1,2-dichloroethene (cis-DCE) caused metabolic inhibition of the 1,4-dioxane-metabolizing

47

bacteria Pseudonocardia dioxanivorans CB1190. The observed decrease in biodegradation rates

48

were attributed to delayed ATP production and down-regulation of the 1,4-dioxane

49

monooxygenase (dxmB) and aldehyde dehydrogenase (aldH) genes essential to the production of

50

enzymes known to be significant in the 1,4-dioxane degradation pathway.23 However, these

51

studies also indicated that the inhibition was non-competitive and reversible, opening up the

52

opportunity for full metabolic recovery once the chlorinated compounds were removed. Hand

53

and coworkers provided similar evidence for TCE-caused inhibition of 1,4-dioxane

54

biodegradation in two co-metabolizing bacteria, Mycobacterium vaccae JOB5 and Rhodococcus

55

jostii RHA1.21 Despite this inhibitory effect, groundwater concentration data and detection of in

56

situ biomarkers for 1,4-dioxane-metabolizing bacteria from 2000 to 2016 provide encouraging

57

evidence for natural 1,4-dioxane attenuation in some plumes co-contaminated with TCE.4,24,25

58

Still, observable biodegradation was limited to aerobic regions of the aquifers and negatively

59

correlated with concentrations of chlorinated volatile organics. Thus, in order for biodegradation

60

of 1,4-dioxane to become a widely used remediation strategy, some form of biostimulation or

61

augmentation is required, along with an economical treatment process to address inhibiting co-

62

contaminants such as TCE.13,26 3 ACS Paragon Plus Environment

Environmental Science & Technology

63

Electrochemical degradation has previously been shown to effectively mineralize

64

chlorinated solvents both by reductive dechlorination and •OH mediated oxidation.27-29 1,4-

65

dioxane is also degraded by electrochemical treatment via strongly oxidizing •OH radicals

66

generated by the oxidation of H2O at the anode.30-32 Our previous work using abiotic flow-

67

through, electrochemical reactors with Ti/IrO2-Ta2O5 electrodes confirmed that 1,4-dioxane

68

(influent concentrations 0.3 to 41.4 mg/L) was degraded into CO2 and small organic acid and

69

aldehyde intermediates32 known to be readily biodegradable.27,33-35 It has also been shown that

70

chloride, often present in natural waters, can potentially be transformed to highly oxidized

71

chlorine species by electrolysis, assisting in the mineralization of 1,4-dioxane and other

72

contaminants,36 although these species could also be destructive to microbial cells.37-40 By taking

73

advantage of the concurrent electrolysis of bulk water to evolve molecular oxygen from the

74

anode half reaction, 2 H2O(l) → O2(g) + 4 H+(aq) + 4e-,41-43 a dramatic shift in redox potential from

75

hypoxic to highly oxic conditions can be achieved. We thus hypothesized that electrochemical

76

treatment would degrade 1,4-dioxane and microbially inhibiting co-contaminants such as TCE

77

while simultaneously generating O2 essential to aerobic respiration, thus leading to enhanced

78

aerobic biodegradation rates of 1,4-dioxane.33,34

79

To test our hypothesis, we built flow-through electrolytic column reactors with

80

dimensionally stable, Ti/IrO2-Ta2O5 mesh electrodes, which are commercially available and have

81

several beneficial properties. Metal oxide electrodes, like Ti/IrO2-Ta2O5, have a higher oxidation

82

state available (i.e. Ir4+ → Ir5+) close to the thermodynamic potential for aqueous oxygen

83

evolution, making them excellent candidates for the electrocatalytic generation of O2 at low

84

power requirements.41,44,45 Published comparisons have shown the relatively low oxygen

85

evolution potential of Ti/IrO2-Ta2O5 (1.5 - 1.8 V vs. SHE, standard hydrogen electrode) also

86

coincides with less disinfection by-product (DBP) formation compared to other electrode

87

materials used for organic contaminant degradation such as PbO2, RuO2-IrO2, Pt-IrO2, and SnO2-

88

Sb.45,46 Detailed reaction schemes describing O2 production and organic pollutant oxidation can

89

be found in the Supporting Information (SI, Reactions 1 - 6). Furthermore, previous studies have

90

demonstrated this mixed metal oxide coating to have favorable surface chemistry interactions and

91

degradation efficiencies with chlorinated contaminants, like TCE.29,47,48 Finally, at a cost of ~400

92

$/m2, it is substantially cheaper than many other electrodes such as boron-doped diamond anodes

93

(~15,000 $/m2),37 and previous field demonstrations, including use as an in situ permeable 4 ACS Paragon Plus Environment

Page 4 of 28

Page 5 of 28

Environmental Science & Technology

94

electrolytic barrier for chlorinated solvent removal, have revealed a long service life (i.e., no loss

95

in electrolytic performance during greater than 2 years of continuous treatment).28,49

96

We used Pseudonocardia dioxanivorans CB1190 (hereafter “CB1190”) as the model

97

bacterium for 1,4-dioxane biodegradation due to its versatile capabilities to metabolize a wide

98

range of organic molecules (although not TCE), while also being able to rapidly metabolize 1,4-

99

dioxane at rates ranging from 1.1 to 19.8 mg·min-1 per mg of protein in the biomass.17,18,50 From

100

among the chlorinated solvents that have been characterized with respect to inhibiting 1,4-

101

dioxane degradation by CB1190,22 TCE was chosen because the dichloroethene isomers are

102

substantially more volatile and may easily be stripped by electrolytically produced gasses, and

103

1,1,1-TCA has shown very little inhibition to CB1190 metabolism.

104

Our specific objectives were to (a) determine whether anodic generation of O2 improves

105

biodegradation rates of 1,4-dioxane and (b) investigate the impacts of voltage potentials and

106

presence of TCE as co-contaminant on degradation kinetics of 1,4-dioxane and spatial CB1190

107

abundance relative to the electrodes. Consequently, this is the first study to provide a

108

fundamental basis for combined electrochemical and biological treatment for 1,4-dioxane-

109

contaminated waters, both when occurring on its own and in the presence of potentially

110

inhibiting co-contaminants.

111 112 113

MATERIALS AND METHODS

114

Chemicals. All chemicals were used as received. 1,4-Dioxane (99.5%, Burdick &

115

Jackson), TCE (99.5%, Alfa Aesar), 1,1-DCE (99%, Alfa Aesar), and vinyl chloride (99%, Alfa

116

Aesar) were used to prepare calibration standards and/or influent contaminant mixtures while

117

dichloromethane (99.96%, OmniSolv Millipore EMD) was used as an extraction solvent prior to

118

quantitation of chemical analytes. Additionally, deuterated 1,4-dioxane-d8 (99% and 99 atom

119

%D, Sigma Aldrich) was used for isotopic dilution quantitation.

120

Sterilization and Disinfection Protocol. All glassware, metal laboratory equipment, and

121

sand used for abiotic control experiments were dry heat-sterilized in a furnace at 232°C for 12-18

122

hours or autoclaved at 121°C and 23 psig for 20 minutes (Tuttnauer 2870 EP Autoclave). Non-

123

autoclavable materials, i.e. work bench surface and the PVC sand column reactors, were

124

disinfected either with 70% ethanol or 10% bleach solutions. 5 ACS Paragon Plus Environment

Environmental Science & Technology

125

Bacterial Strain and Culture Conditions. The model 1,4-dioxane metabolizing

126

bacterium, Pseudonocardia dioxanivorans strain CB1190, was harvested by a 1% (v/v) transfer

127

from an actively growing pure culture into ammonium mineral salts (AMS) nutrient medium

128

similar to previously reported procedures (Appendix A in Supporting Information).17,22 The AMS

129

medium’s main constituents, 660 mg/L (NH4)2SO4 and 1000 mg/L MgSO4·7H2O, serve as

130

important nitrogen and sulfur sources for CB1190. In addition, the AMS medium serves as a

131

proxy for groundwater since it consists of a complex mixture of other inorganic ions commonly

132

found in groundwater environments such as Ca2+, Fe2+, Zn2+, Mn2+, SO42- and Cl-. Aqueous

133

CB1190 cultures were grown aerobically in AMS medium and sequentially harvested by 1 - 10

134

% (v/v) transfers into larger and larger volumes of fresh AMS solution, ending in 4.0-L

135

polycarbonate Nalgene containers, which were then used to inoculate silica sand (Figure S3).

136

Spikes of 1,4-dioxane were added every 2 to 5 days, maintaining levels at 80 - 100 mg/L, to

137

provide ongoing renewal of the sole carbon and energy source. Throughout the process, aqueous

138

and sand cultures were incubated at 30°C with continuous agitation at 100 rpm to

139

homogeneously mix the 1,4-dioxane carbon source and micronutrients, and infuse oxygen. Only

140

“active” CB1190 cultures were used to inoculate sand, and only “active” batches of this

141

homogeneously mixed inoculated sand were used to pack into bioaugmented column reactors.

142

Initial CB1190 population densities (planktonic and sessile) were measured by qPCR analysis

143

immediately following transfer into column reactors. Targeting “active” cultures was meant to

144

provide sand containing CB1190 communities at peak population density and metabolic activity

145

prior to initiating each flow-through column experiment. We characterized “active” CB1190

146

cultures as those with (a) consistent, rapid 1,4-dioxane biodegradation (biodegradation rates > 10

147

mg/L/day), (b) high CB1190 bacteria populations detected on aerobic count plates (1:1000

148

dilution having > 5 colonies/cm2 of petrifilm plate), and (c) evidence of the culture experiencing

149

mid- to late-exponential growth phase indicated by increased bacterial ATP production (Figure

150

S3). To track ATP concentrations over time, luminescence analysis (BioTek Synergy HT) was

151

completed within two hours of sampling using the Promega BacTiter-GloTM Microbial Cell

152

Viability Assay following Promega Technical Bulletin #TB337 and Protocol for Measuring ATP

153

from Bacteria Bulletin. Bacterial abundance was monitored by counting bacterial colonies on 3M

154

Petrifilm Aerobic Count Plates following manufacturer’s protocol.

6 ACS Paragon Plus Environment

Page 6 of 28

Page 7 of 28

Environmental Science & Technology

155

Flow-Through Column Reactors. Bench-scale flow-through experiments were

156

performed using 10-cm I.D. x 45-cm long clear PVC column reactors (Figure 1 and Figure S1),

157

packed with 8-12 mesh quartz silica sand and two permeable, disc-shaped Ti/IrO2-Ta2O5 mesh

158

electrodes installed perpendicular to flow (78.5 cm2 cross-sectional area, 1mm thick with 1.0 x

159

2.8 mm diamond-shaped openings, Corrpro Companies). All column reactors were operated in

160

the dark, under opaque plastic, to prevent potential photolysis of 1,4-dioxane. PVC column

161

reactors were chemically disinfected (70% ethanol) between experiments and repacked with

162

CB1190-inoculated silica sand for all bioaugmented experiments, and repacked with heat-

163

sterilized silica sand (232°C for 18 hours) for all non-bioaugmented control experiments. One

164

column reactor was used for all 3V experiments, a second column reactor for all 8V experiments,

165

and a third was used for all 0V experiments.

166

In addition to the influent (12.5 cm before anode) and effluent (32.5 cm downstream of

167

anode) liquid sample ports, three additional liquid ports (L1, L2, and L3) and solid ports (S1, S2,

168

and S3) were installed along the column flow path at distances of 2.5, 12.5, and 22.5 cm

169

downstream of the leading anode (Figure 1). Thus, L1 (S1) is located midway between the

170

leading anode (positive polarity) and trailing cathode (negative polarity) which have 5.0 cm of

171

separation between them.

172

7 ACS Paragon Plus Environment

Environmental Science & Technology

-12.5

0

2.5

12.5

22.5

RE2

RE1

Page 8 of 28

32.5cm

PVC PVC tube endcap

gas vents

Direction of Flow S1

S2

S3

Leffluent

Linfluent

+

L1

-

L2

L3

Contaminant Feedstock 1,4-Dioxane in AMS medium (TCE as co-contaminant)

Effluent Reservoir

+ - anode & cathode working electrodes S L RE

173

solid sample ports liquid sample ports Ag/AgCl reference electrode (redox) silica sand (8/12 mesh)

174 175 176 177 178

Figure 1. Schematic of flow-through electrolytic reactors used for non-bioaugmented electrolytic degradation, bioaugmented biodegradation and combined electro-biodegradation experiments. Solid sample ports have removable threaded PVC plugs (1” diameter) to allow access to sand within the reactor. Liquid sample ports have 3-way valves. Gas vents are exhausted into large tedlar bags.

179

Influent feedstock (in 20-L glass carboys) was composed of degassed, hypoxic AMS

180

medium spiked with 100 mg/L 1,4-dioxane (and additional 5 mg/L TCE for co-contaminant

181

experiments). A high 1,4-dioxane concentration was chosen so that CB1190 biodegradation

182

rates would not be limited by electron donor availability and to assess degradation performance

183

under challenging conditions, such as in source zones and industrial wastewaters.3,5 The specific

184

conductivity of the medium was 3.4 - 3.6 mS/cm and initial dissolved oxygen concentration

185

(DO) after degassing was 2.9 - 3.1 mg/L. The pH was adjusted to 6.9 ± 0.1 using NaOH before

186

adding phosphate buffer (KH2PO4 / K2HPO4). Completely anoxic feedstock conditions could not

187

be maintained without the addition of unwanted oxygen scavenger compounds that may have

188

interfered with electrochemical reactions or biological functions. All flow-through sand column

189

experiments were operated at 22 ± 2°C (ambient temperature) and a flow rate of 1.07 mL/min. 8 ACS Paragon Plus Environment

Page 9 of 28

Environmental Science & Technology

190

Constant feedstock flow rates (Q) of 1.07 mL·min-1 were confirmed each day by volumetric

191

analysis. To account for the sand column reactor porosity (ϕ, average of 0.43) and the flux

192

through the reactor’s cross-sectional area (A, 78.5 cm2), flow rate is expressed as its seepage

193

velocity (vs) of 46 cm/d, since vs = Q / (A · ϕ) = (1.07cm3·min-1 x 1440min·day-1) / (78.5cm2 x

194

0.43). Ten different experimental regimes were tested for the treatment of 100 mg/L 1,4-dioxane

195

feedstock under the following conditions: 3V ± CB1190 ± TCE, 8V ± CB1190 ± TCE, and 0V +

196

CB1190 ± TCE (Figure S1). To minimize sorption effects, feedstock solution was flowed

197

through each column reactor prior to each new treatment regime until influent and effluent

198

contaminant concentrations were stable (± 3% coefficient of variation). The target voltage was

199

then initiated (0, 3.0 or 8.0 V), and effluent concentrations were monitored until achieving

200

steady-state conditions (i.e. stable effluent concentrations over time). Steady-state conditions

201

were achieved within 3 - 5 pore volumes (3 - 5 days), and replicate aqueous samples (n ≥ 3) of

202

the influent and effluent were taken at 1 - 2 day intervals. Aqueous samples were filtered with

203

Acrodisc 0.45-µm nylon membrane syringe filters (Pall Corporation) and extracted into

204

dichloromethane solvent prior to analysis for 1,4-dioxane and chlorinated ethenes using an

205

Agilent 6890N gas chromatograph (GC) coupled to an Agilent 5973N mass spectrometer (MS)

206

in full scan mode (m/z 40-250 Da) and selected ion monitoring (SIM) mode. 1-µL injections

207

were made using a 4:1 split flow ratio and an inlet temperature of 250°C. The GC was equipped

208

with a Restek Rxi-624Sil MS mid-polarity column (30 m x 0.25 mm ID x 1.4 µm df). The

209

Helium carrier gas was to set to constant flow at 2.0 mL/min. The initial oven temperature was

210

held at 40°C for 2 minutes, then ramped at 8°C/min to 100°C, followed by an additional ramp of

211

40°C/min to 160°C and held for 1 minute.

212

The MS was programmed to scan for m/z 62 and 64 (vinyl chloride) in segment 1 from

213

1.0 to 3.52 minutes after injection. Segment 2 was set to scan for m/z 61 and 96 (DCE isomers)

214

until 5.0 minutes when segment 3 began scanning for m/z 95 and 130 (TCE). Segment 4 started

215

at 6.25 minutes scanning for m/z 64 and 96 (1,4-dioxane-d8) as well as m/z 58 and 88 (1,4-

216

dioxane). Each ion was assigned a dwell time of 100 µs. Quantitation with GC/MS(SIM) for all

217

chlorinated compounds was performed using external calibration standards. External standard

218

calibration was also used for 1,4-dioxane in experiments with 1,4-dioxane as the only

219

contaminant in the feedstock. Isotopic dilution calibration was use to quantify 1,4-dioxane in all

220

co-contaminant experiments, using 1,4-dioxane-d8 as the internal standard to correct for analyte 9 ACS Paragon Plus Environment

Environmental Science & Technology

Page 10 of 28

221

losses due to sample preparation or variations in instrument response. Calibration was obtained

222

by plotting the ratio of the analyte signal to the 1,4-dioxane-d8 signal as a function of the analyte

223

standard concentration. Further analytical method descriptions are provided in the Supporting

224

Information.

225

Physicochemical Measurements. Daily measurements were made of voltage and current

226

between the anode and cathode (Fluke Multimeter). Solution oxidation-reduction potential (ORP)

227

was measured against Ag/AgCl reference micro-electrodes (RE-5, World Precision Instruments)

228

at two locations within the column, RE1 and RE2 in Figure 1. Solution pH was measured for all

229

experimental regimes in the influent, the effluent, and from aqueous ports L1, L2, and L3 along

230

the column flow path (Figure 1). The pH was measured using a pH electrode (±0.1 pH unit

231

precision) and confirmed by pH indicator strips at beginning and end of experiments. Specific

232

conductivity and dissolved oxygen levels were measured comprehensively only for the

233

bioaugmented/mixed contaminant experiments using Hach HQ40d meter with graphite

234

conductivity and luminescent DO probes. Calibration of the DO probe with auto salinity

235

corrections was performed according to the water-saturated air (100%) procedure in

236

manufacturer’s operation manual.

237

Quantitative Polymerase Chain Reaction (qPCR). Nucleic acid primers for the dxmB

238

gene, which codes for the dioxane monooxygenase β subunit, were used to quantify this target by

239

qPCR analysis as described in Gedalanga, et al.23 Additionally, the dxmB gene target was used as

240

a proxy for CB1190 population abundance due to its known requirement for 1,4-dioxane

241

biodegradation.23 At the start and completion of each ~2-week flow-through experiment, 0.5-mL

242

liquid samples and 0.5-g solid sand samples were collected into 2.0-mL microcentrifuge tubes,

243

sealed, and frozen at -20°C. Liquid aliquots were sampled via passive flow from valves at the

244

influent, inter-column locations L1, L2, L3, and effluent (duplicates collected from each

245

location). Removable, threaded PVC plugs at ports S1, S2, and S3 provided access to collect

246

duplicate sand samples from center and outer portions of each reactor with heat-sterilized, 1.0-cm

247

diameter metal tubes (detailed description in SI). Replicate qPCR analyses were performed for

248

each duplicate sample collected, and the average of the four values obtained was used to estimate

249

CB1190 abundance at each location along the column flow path.

250

In preparation for qPCR analysis, DNA was extracted from sand and liquid phase samples

251

using a bead beating method followed by phenol/chloroform purification.23 Briefly, liquid 10 ACS Paragon Plus Environment

Page 11 of 28

Environmental Science & Technology

252

samples were centrifuged to pellet the biomass for 3 minutes at 13,200 x g. The supernatant was

253

discarded and DNA was extracted from the pelleted biomass by addition of 0.25 mL extraction

254

buffer, 0.1 mL 10% sodium dodecyl sulfate, and 1 mL saturated phenol to all tubes. Samples

255

were heated at 65˚C for 2 minutes followed by bead beating for 2 minutes using a minibead

256

beater-16 (Biospec Products, Bartlesville, OK). Lysed samples were incubated at 65˚C for 8 min

257

followed by another round of bead beating for 2 min. Samples were centrifuged and the lysate

258

was transferred to a sterile 1.7-mL microcentrifuge tube for phenol/chloroform purification.

259

Nucleic acid extracts were resuspended in 100 µL of nuclease-free H2O and stored at -80˚C until

260

further analyses.

261

All qPCR reactions were performed in a total volume of 20 µL containing 1X Kapa Sybr

262

Fast qPCR Master Mix (Kapa Biosystems, Wilmington, MA), 0.25 µM of each primer

263

(IDTDNA, San Diego, CA), and 2 µL of template DNA. All reactions were performed on an

264

Applied Biosystems StepOnePlus real-time PCR system (Life Technologies, Carlsbad, CA) as

265

previously described23 and were accompanied with a melt curve analysis to confirm the

266

specificity of qPCR products.

267

(Minimum Information for Publication of Quantitative Real-Time PCR Experiments) can be

268

found in Table S3.

Additional details following MIQE reporting requirements

269 270 271

RESULTS AND DISCUSSION

272

1,4-Dioxane Degradation in the Absence of Co-contaminant. Investigations on

273

coupled electrochemical and biological treatment of 1,4-dioxane were performed at flow rates of

274

1.07 mL/min, or seepage velocity of 46 cm/d, in sand-packed flow-through column reactors

275

equipped with permeable Ti/IrO2-Ta2O5 mesh electrodes (Figure 1). In non-bioaugmented

276

(“abiotic”) reactors at 3.0 V and 8.0 V in the absence of TCE, only 14.6 and 11.7 mg 1,4-dioxane

277

were oxidized per hour per m2 of electrode surface area, respectively (uncertainty of ± 13.9 mg·h-

278

1

279

with electrochemical oxidation, additional electrode pairs would need to be added sequentially

280

down the flow path to increase hydraulic retention time and improve overall degradation

281

capacity. Although higher concentrations of reactive •OH radicals would be generated at 8.0 V

282

(2.34 mA/cm2) than at 3.0 V (0.20 mA/cm2), these two voltage applications for non-

·m-2, Figure 2). Thus, in a full-scale application treating high contaminant concentrations only

11 ACS Paragon Plus Environment

Environmental Science & Technology

Page 12 of 28

283

bioaugmented columns exhibited an insignificant difference in degradation rate (p = 1.0). The

284

reason for 8.0 V producing equal (or slightly lower than 3.0 V) removal rates can be justified by

285

the overall reaction rate being controlled by mass transfer setting the upper constraint on

286

degradation rate. The limitation on oxidation of 1,4-dioxane by •OH radicals on, or very near, the

287

electrode surface is compounded in the 8.0 V reactor by more pronounced visible coverage of the

288

mesh electrodes with gas bubbles, thereby reducing hydraulic conductivity and creating

289

preferential flow paths.32,51,52

290

291 292 293 294 295 296 297 298

Figure 2. 1,4-Dioxane degradation rates for non-bioaugmented and P. dioxanivorans CB1190 bioaugmented reactors in the absence (striped) and presence (solid) of TCE co-contaminant (n ≥ 3). The percentage of TCE removed during the mixed co-contaminant experiments is represented by the shaded region of the pie charts above the corresponding bar plot. Error bars of ±13.9 mg·h1 ·m-2 were generated by transforming a precision calculation of the mean absolute deviation for instrumental measurements of influent 1,4-dioxane concentrations (calculations shown in Table S1). 12 ACS Paragon Plus Environment

Page 13 of 28

Environmental Science & Technology

299

For bioaugmented experiments, the sand was inoculated with “active” CB1190

300

transferred at, or near, peak population density and activity, as described in the Materials and

301

Methods section. In the CB1190 bioaugmented control column (no voltage) with degassed

302

feedstock (initial DO of 3.0 ± 0.1 mg/L, ORP of 0.98 V vs. SHE), a 1,4-dioxane degradation rate

303

of 68.7 mg·h-1·m-2 was observed, about 5 times faster than in either non-bioaugmented

304

electrolytic column, and demonstrating that the microaerophilic CB1190 has the capacity to

305

metabolize 1,4-dioxane even at hypoxic DO levels (~2-3 mg/L). However, previous

306

investigations have shown that the 1,4-dioxane biodegradation capacity of CB1190 would cease

307

in a purely anoxic environment. When electrolysis and biodegradation processes were combined,

308

degradation rates substantially increased in an over-additive manner to 169 mg·h-1·m-2 at 3.0 V

309

and 101 mg·h-1·m-2 at 8.0 V. This degradation rate of 169 mg·h-1·m-2 in the bioaugmented reactor,

310

the highest achieved in this study, was 12 times higher than non-bioaugmented 3.0 V electrolysis,

311

15 times higher than non-bioaugmented 8.0 V electrolysis, and 2.5 times higher than the

312

bioaugmented control reactors without applied potential. The improvement of electro-

313

biodegradation rates over biotic treatment alone would be expected to be even greater had we

314

been able to achieve maintain completely anoxic conditions in preparing the feedstock solutions.

315

The dramatic increase in 1,4-dioxane removal rate has to be attributed to anodic O2 generation

316

resulting in an advantageous environment for aerobic biodegradation processes42 since the

317

coupled treatment regime at 3.0 V performed significantly better than either treatment on its own.

318

The manifestation of a highly oxidative environment was evidenced by the considerable

319

generation of O2 gas bubbles at the anode and by elevated solution ORP measurements at the

320

anode of 1.8 V and 4.4 V vs. SHE for the electro-bioreactors at 3.0 and 8.0 V, respectively (Table

321

1). We were unable to perform DO measurements in these reactors; however, DO concentrations

322

measured in analogous bioaugmented reactors with TCE present exhibited extraordinarily high

323

concentrations of 11.0 and 15.7 mg/L at 3.0 and 8.0 V, respectively (Table S2). Since ORP

324

measurements in Table 1 show comparable mean values near 1.7 ± 0.3 V for all experiments with

325

3.0 V applied, it is reasonable to use ORP as a proxy for revealing dissolved oxygen shifts and

326

assume that all 3.0 V reactors generated DO concentrations in the range of 5 to 11 mg/L. Hence,

327

by providing O2 as a terminal electron acceptor for aerobic metabolism, concurrent electrolysis

328

and biodegradation processes outperformed the degradation efficiencies of all other regimes

329

tested. 13 ACS Paragon Plus Environment

Environmental Science & Technology

330 331 332

Page 14 of 28

Table 1. Physicochemical parameters measured along the column flow path. Data is divided into 1,4-dioxane degradation experiments conducted without TCE (a) and with 5 mg/L of TCE cocontaminant (b).

333 (a)

Non-bioaugmented, 1,4-dioxane (-) TCE Sample port

2

3V and 0.2 mA/cm *

Bioaugmented with CB1190, 1,4-dioxane (-) TCE

2

2

8V and 2.3 mA/cm

0V and 0 mA/cm

2

3V and 0.3 mA/cm

2

8V and 1.6 mA/cm

distance downgradient

pH

ORP (V)

pH

ORP (V)

pH

ORP (V)

pH

ORP (V)

pH

ORP (V)

influent

7.0

0.6

7.0

0.6

6.8

0.7

6.8

0.98 ± 0.5

6.8

0.98 ± 0.5 4.4

S1 = 2.5 cm

8.4 ± 3.1

1.6

9.1 ± 2.9

4.2

6.8

0.3

4.7

1.8

3.1 ± 0.8

S2 = 12.5 cm

6.9

-1.0

6.8

-1.1

6.8

0.1

6.5

0.1

5.8

0.0

S3 = 22.5 cm

7.0

0.1

6.9

-0.1

6.8

-0.2

6.7

0.1

6.3

-0.2

effluent =32.5 cm

6.9

0.3

6.8

0.1

-0.2

6.8

0.2

6.3

0.2

standard deviation**

± 0.3

± 0.05

± 0.3

± 0.05

6.8 ± 0.3

± 0.2

± 0.3

± 0.2

± 0.3

± 0.3

(b)

Non-bioaugmented, 1,4-dioxane (+) TCE Sample port

distance downgradient

2

3V and 0.2 mA/cm * pH

ORP (V)

Bioaugmented with CB1190, 1,4-dioxane (+) TCE 2

0V and 0 mA/cm2

8V and 1.2 mA/cm pH

ORP (V)

pH

ORP (V)

3V and 0.2 mA/cm2 pH

ORP (V)

8V and 1.1 mA/cm2 pH

ORP (V)

influent

7.0

0.6

7.0

0.6

7.0

0.5

7.0

0.5

7.0

0.5

S1 = 2.5 cm

6.5 ± 1.7

1.7

2.3 ± 0.5

3.7

7.0

0.2

7.3 ± 0.6

1.6

5.3

S2 = 12.5 cm

7.5 ± 1.7

0.0

9.0

-0.2

7.0

-0.1

7.0

0.1

12.0 11.3 ± 1.2

S3 = 22.5 cm

7.0

0.2

6.8 ± 0.5

0.3

7.0

-0.1

7.0

0.3

9.5 ± 0.9

0.4

effluent =32.5 cm standard deviation**

6.6

0.3

±0.3

± 0.03

5.5 ± 0.3

0.0

0.4

7.0

-0.1

7.0

0.7

4.2

0.8

± 0.2

±0.3

± 0.1

± 0.3

± 0.2

± 0.3

± 0.4

ORP, oxidation reduction potential vs. SHE (standard hydrogen electrode) *all current densities are averages of n =3, with uncertainties less than ± 0.01 mA/cm2 **the standard deviation (n=3) is explicitly written for measurements when exceeding the common one shown below each column

334

335

Although electrolysis provides O2 necessary for aerobic biodegradation, electrochemical

336

processes may also cause cellular death associated with the production of biologically destructive

337

hydroxyl radicals (SI, Reactions 1 to 6)53 or highly oxidized chlorine species (e.g., hypochlorous

338

acid) and other DBPs.37,54 In addition, considerable pH fluctuations near the electrodes may be

339

harmful to microbial populations as well. Electrolysis commonly produces an acidic boundary

340

layer at the anode surface due to the oxidation of water molecules to form H+ ions, and more

341

alkaline conditions surround the cathode due to H+ reduction to H2 gas and production of OH-

342

ions in solution.55 Hence, it was important that we investigated the impacts of these potentially

343

adverse conditions on the viability of CB1190 by analyzing both liquid (planktonic) and

344

solid/sand (biofilm) aliquots at various positions along the column reactor to locate zones of

345

microbial inhibition or proliferation adjacent to, or downstream of, the anode. Quantitative PCR 14 ACS Paragon Plus Environment

Page 15 of 28

Environmental Science & Technology

346

data on the dxmB gene biomarker was used as a proxy for CB1190 cell abundance to elucidate

347

preferential location(s) of microbial proliferation, either in biofilm or planktonic forms, leading

348

to a better understanding of optimum spacing between multiple electrode pairs or reactor

349

dimensions.

350

Upon CB1190 inoculation of the sand used in columns for the 0 V, 3.0 V and 8.0 V

351

treatments of 1,4-dioxane in the absence of TCE, initial measurements of mean abundance values

352

after packing the reactors were 4.1×108 cells/mL for planktonic form and 1.3×107 cells/g for

353

CB1190 present as biofilm on sand particles (Figure 3 a,b). These levels are thought to represent

354

maximum population density achievable on this sand media since the cultures were growing

355

under ideal conditions up until this point. Considering the total volume of water and total mass of

356

sand in the reactors, we note that similar to previous reports,56 the planktonic biomass was equal

357

to or slightly greater than biofilm-associated biomass.

358

After two weeks of flow-through operation in the biological control (0 V) reactor, the pH

359

remained stable at 6.8, the planktonic CB1190 abundances dropped from 3.7×108 cells/mL at

360

port L1 to 1.0×107 at the effluent site down gradient. The biofilm levels also dropped by two

361

orders of magnitude down to 1.5×105and 2.1×105 cells/g at solid sample ports S3 and S5,

362

respectively. Thus, CB1190 growth rates were at least sufficient enough to overcome the steady-

363

state biomass losses of 1.0×107 cells/mL measured in the effluent caused by hydraulic shear

364

forces.57 Although these losses in microbial populations were observed, the remaining CB1190

365

was in quantities high enough to produce the 1,4-dioxane biodegradation rate observed here of

366

68.7 mg·h-1·m-2.18,22 Table 1 shows that ORP values along the column were steadily decreasing

367

from 0.7 to -0.2 V vs. SHE, likely due to biochemical oxygen demand for CB1190’s cellular

368

respiration. This decrease in CB1190 communities correlated to more negative ORP levels would

369

add credence to the need for adding charged electrodes to generate beneficial oxygen

370

downgradient.

371

15 ACS Paragon Plus Environment

Environmental Science & Technology

Page 16 of 28

372 373 374 375 376 377 378 379 380

Figure 3. P. dioxanivorans CB1190 bioaugmented plots showing planktonic abundance (a,c) and biofilm abundance (b,d) of CB1190 cells along the horizontal flow path in the absence (a,b) and presence (c,d) of TCE co-contaminant, plotted as a function of distance from the anode. Sampling ports 1, 2, 3 and effluent correspond to 2.5, 12.5, 22.5 and 32.5 cm downstream from the anode. Any samples that were below the qPCR method limits of detection (LOD), 10 cells/mL for liquid samples and 40 cells/g for solid samples, were plotted just below LOD line. The error bars represent the average range of qPCR duplicates (2 analytical replicate analyses of each duplicate sample).

381 382

At the low stimulation voltage of 3.0 V, ORP levels reached 1.8 V vs SHE and pH levels

383

dropped to 4.7 between the electrodes, which is near the growth range previously reported for

384

CB1190 from pH 5.0 - 8.0.17 After the cathode, the pH rapidly returned to the starting influent

385

pH of 6.8 (Table 1).

386

experimental and modeling studies have demonstrated that their high reactivity limits their

387

existence to a narrow zone of less than 1 µm from the anode surface.55,58-60 Consequently, any

Although free radicals like •OH can be damaging to cellular life,53

16 ACS Paragon Plus Environment

Page 17 of 28

Environmental Science & Technology

388

adverse conditions caused by the presence of •OH are only expected in the immediate vicinity of

389

the anode. Despite these risks, high mean planktonic abundances near 1.5×108 cells/mL along the

390

reactor flow path revealed that the overall conditions remained conducive to cellular growth

391

(Figure 3 a,b) and reported greater overall 1,4-dioxane degradation rates than biological control

392

rates. Our measurements revealed that CB1190 populations were not homogenous at different

393

distances from the anode. At sample port 1, between the electrodes, biofilm counts were below

394

the qPCR detection limit (BDL, < 40 cells/g); and planktonic cell counts dropped slightly from

395

4.1×108 initially to 6.8×107 cells/mL after equilibrating to the 3.0 V system for two weeks. The

396

subsequent CB1190 population rebound to 3.0×108 planktonic cells/mL and 1.3×107 sessile

397

cells/g at the location 12.5 cm downstream of the anode reveals a possible “sweet spot” for

398

bacterial proliferation along the flow path where dissolved oxygen is still abundant (likely in the

399

4 - 7 mg/L range) and the distance away from the electrodes was sufficient to avoid deleterious

400

effects. Physicochemical measurements in Table 1 show both locations 12.5 and 22.5 cm

401

downstream of the anode support this hypothesis in that solution ORP was 0.1 V vs SHE and the

402

pH returned to circumneutral (6.5-6.7). Biofilms are dynamic microbial communities capable of

403

interchangeable transitions between sessile and planktonic modes of growth as a response to

404

different environmental cues, including carbon source, oxygen saturation and pH of the

405

media.61,62 The existence of localized maximum cell counts of both biofilm and planktonic forms

406

could indicate that environmentally-tolerant biofilms may be the foundation of a stable CB1190

407

microbial community, with dispersed planktonic cells primarily responsible for higher rates of

408

carbon (1,4-dioxane and transformation products) metabolism. This type of survival strategy has

409

been documented in other bacteria and could warrant further study into the predominance of the

410

role played by these planktonic CB1190 cells dispersed from densely packed and specialized

411

biofilm subpopulations.63,64

412

When a higher potential of 8.0 V was applied, an elevated solution ORP of 4.4 V vs.

413

SHE was measured after the anode, which can be explained by the expected increase in anodic

414

generation of O2 and other reactive oxygen species (ROS) due to the higher voltage and current

415

density.55 We hypothesized that this occurrence, in combination with a drastic drop in pH from

416

6.8 to 3.1, could create conditions less hospitable for microbial growth and/or survival. This was

417

confirmed with measurements between the electrodes showing biofilm levels dropped to below

418

the qPCR detection limit and a substantial 4 order of magnitude decrease in planktonic 17 ACS Paragon Plus Environment

Environmental Science & Technology

Page 18 of 28

419

abundance was observed as well (Figure 3 a,b). And although planktonic cells did rebound to

420

2.3×108 cells/mL 12.5 cm downstream from the anode, biofilm counts remained below LOD for

421

the remainder of the column. Thus, the decline in both life cycle modes of CB1190 communities

422

in the 8.0 V column is understood to be the principal reason for why lower overall 1,4-dioxane

423

degradation rates were obtained from the 8.0 V column compared with the 3.0 V column. In

424

addition, the lower degradation rates provide further support for the probable necessity of a

425

critical mass of biofilm being present, acting as a base for planktonic dispersal, in order for

426

optimal degradation rates to be achieved.

427

Finally, we note that ~104 counts (3.0 V) and ~102 counts (8.0 V) of dxmB genes were

428

detected in the non-bioaugmented reactor experiments (Figure S4). However, these data points

429

may be due to the fact that non-bioaugmented experiments were performed after augmented ones

430

for logistical reasons. Thus, we suspect that these detections are the result of extracellular DNA

431

released from lysed CB1190 cells during the column disinfection and sand heat-sterilization

432

process.

433

TCE Co-contaminant Impact on 1,4-Dioxane Degradation. Non-bioaugmented

434

electrolytic experiments performed in the presence of TCE co-contaminant (Figure 2) exhibited

435

1,4-dioxane degradation rates of 0.06 ± 13.9 mg·h-1·m-2 at 3.0 V (maximum ORP 1.7 V vs. SHE)

436

and 6.4 ± 13.9 mg·h-1·m-2 at 8.0 V (maximum ORP 3.7 V vs. SHE). These outcomes were not

437

significantly different from each other (p = 1.0), nor were they significantly different from

438

equivalent experiments spiked solely with 1,4-dioxane (p = 0.79 at 3.0 V, p = 0.92 at 8.0 V)

439

because rates of abiotic (electrolytic) 1,4-dioxane removal were controlled by mass transfer.58,65

440

In addition, 1.4 mg/L TCE (27% of the initial 5 mg/L) was removed at 3.0 V and 3.0 mg/L TCE

441

(60%) at 8.0 V (Figure 2 and Figure S5), showing higher electrolytic removal than for 1,4-

442

dioxane. This is expected because 1,4-dioxane degradation rates are limited to anode-generated

443



444

in addition to reductive dechlorination by direct electron transfer at the cathode. Additionally,

445

overall degradation kinetics for TCE can be enhanced by favorable surface chemistry interactions

446

with IrO2 electrode surfaces.47 GC/MS(SIM) analysis of effluent did not detect any DCE isomer

447

or vinyl chloride intermediates. Furthermore, no other organic transformation products appeared

448

as new chromatographic peaks in GC/MS full scan analysis, signifying that TCE was

449

mineralized, or volatilized/stripped by the effervescent oxygen and hydrogen gas bubbles.

OH radical oxidation pathways, whereas oxidation of TCE can occur via •OH radical pathways

18 ACS Paragon Plus Environment

Page 19 of 28

Environmental Science & Technology

450

Previous studies on the electrochemical treatment of TCE have reported carbon dioxide, carbon

451

monoxide, chloride, formate, acetate, and chloroxyanions as stable products, but failed to detect

452

organochlorine intermediates, indicating that these may be too short-lived to accumulate in the

453

bulk solution.27,35

454

In the 0 V biological control column at 46 cm/d flow velocity, the addition of 5 mg/L

455

TCE to the 100 mg/L 1,4-dioxane feedstock lowered 1,4-dioxane biodegradation rates from 68.7

456

mg·h-1·m-2 (in the absence of TCE) to 37.5 mg·h-1·m-2 (Figure 2). This outcome is supported by

457

previously mentioned studies that show inhibitory effects of TCE on the biodegradation rates of

458

CB1190.22 Steady-state analysis revealed that no TCE removal had occurred, confirming

459

previous reports that CB1190 is not capable of biodegrading TCE20 and serving as an

460

experimental control that sorption did not contribute to TCE removal from the aqueous phase

461

after steady-state flow-through conditions had been achieved. The pH of 6.8 remained constant

462

throughout the entire biological control column and the solution ORP decreased from 0.5 in the

463

influent down to -0.1 V vs. SHE, analogous to our earlier experiments performed in the absence

464

of TCE (Table 1).

465

In the mixed contaminant experiments, 1,4-dioxane oxidation rates were again highest

466

when both abiotic and biodegradation processes were combined, achieving rates of 98.4 mg·h-

467

1

468

was minor in non-bioaugmented experiments; thus, the vast majority of 1,4-dioxane oxidation

469

observed here can be attributed to electrolytic enhancement of aerobic biodegradation rates. The

470

improved treatment is understood to be the result of increased biodegradation kinetics stimulated

471

by anodic production of molecular oxygen and the simultaneous benefit from electrochemical

472

removal of the inhibitive TCE co-contaminant. This claim is supported by DO measurements. As

473

stated above, O2 concentrations between the electrodes at port L1 increased to 11.0 mg/L at 3.0 V

474

and 15.6 mg/L at 8.0 V compared to 2.4 mg/L in the hypoxic bioaugmented control column, and

475

remained above 6 mg/L throughout the entire column reactors, while the biological control

476

experiment showed steadily decreasing DO values down to 1.9 mg/L along the flow path (Table

477

S2). Although DO measurements were not made in the experimental treatments of 1,4-dioxane in

478

the absence of TCE, the similarly decreasing trend in ORP values correlated to distances farther

479

downstream of the electrodes (Table S2) would signify that DO concentrations would also

480

decrease downstream. However, it may be critically important to note that when TCE is present

·m-2 at 3.0 V and 94.5 mg·h-1·m-2 at 8.0 V. Abiotic electrochemical oxidation of 1,4-dioxane

19 ACS Paragon Plus Environment

Environmental Science & Technology

Page 20 of 28

481

as an inhibitor to CB1190 metabolism, it appears that the decreased DO levels along the flow

482

path could cause the precipitous drop in planktonic populations to below 2.0×108 cells/mL

483

measured at the effluent ports in 0V, 3V and 8.0 V reactors (Figure 3 c). Therefore, in situ

484

treatment of hypoxic waters (e.g. groundwater and wastewater), with much longer hydraulic

485

retention times would benefit from repeating intervals of electrodes to maintain high levels of

486

dissolved oxygen and high biodegradation rates.

487

At the higher stimulation voltage (8.0 V), 3.1 mg/L (62%) of TCE was removed (Figure

488

2 and Figure S5), minimizing adverse effects on biodegradation by CB1190 such that 1,4-

489

dioxane removal rates were nearly equivalent to rates when TCE was not present (94.5 compared

490

to 101 mg·h-1·m-2, p = 0.90). The recovery in metabolic biodegradation rates observed here is

491

consistent with conclusions by Zhang and co-workers (2016) that inhibition was dose-dependent

492

and reversible once chlorinated compounds were removed.22 Despite the removal of 2.05 mg/L

493

TCE (41%) with 3.0 V applied, the remaining 2.9 mg/L TCE appeared to decrease 1,4-dioxane

494

biodegradation efficiency by 40% under these conditions. Overall, our data demonstrate that

495

aerobic biodegradation rates can be enhanced by upstream electrolysis, and that complete

496

removal of TCE is not required to obtain effective electro-biodegradation of 1,4-dioxane;

497

although more investigation is needed to better understand whether a certain low threshold

498

concentration for TCE relative to CB1190 abundance may be needed to eliminate any noticeable

499

inhibition effects.

500

Adverse microbial impacts are observed with the presence of TCE since qPCR analyses

501

for the bioaugmented experiments revealed that mean planktonic cell counts under all voltage

502

conditions were generally orders of magnitude lower than comparable experiments in the absence

503

of TCE (Figure 3 a-d, Table S4).20-22 In contrast, the mean biofilm counts in the presence of TCE

504

tended to be higher than mean values when TCE was not present, possibly indicating a stress

505

response to toxicity posed by the presence of chlorinated solvents.66 Physicochemical

506

measurements also reinforced our expectation for less-viable conditions near the 8.0 V electrode.

507

For mixed contaminant experiments, the 8.0 V bioaugmented reactor recorded a highly oxidative

508

ORP of 5.3 V vs. SHE, along with highly alkaline pH levels of 12.0, 11.3 and 9.5 being

509

measured at 2.5, 12.5, and 22.5 cm downstream of the anode; whereas, in the 0 and 3.0 V

510

bioaugmented reactors the ORP values did not exceed 1.6 V vs. SHE and the pH remained

511

between 7.0 - 7.3 (Table 1). Much lower CB1190 planktonic abundance (5.2 x 103 cells/mL) was 20 ACS Paragon Plus Environment

Page 21 of 28

Environmental Science & Technology

512

observed between the electrodes when 8.0 V was applied, when compared to the 0 V (1.7 x 105

513

cells/mL) and 3.0 V (1.6 x 105 cells/mL) treatments (Figure 3 c,d). Thus, it is plausible that

514

sparse CB1190 populations in the 8.0 V experiment are caused by TCE inhibition of

515

growth/metabolism compounded by the rapid increase in pH and ORP levels, and potential for

516

greater abundance of reactive oxygen species.18 The high pH level does not appear to be caused

517

by reaction pathways isolated to having TCE present, since both of the non-bioaugmented

518

experiments without TCE had alkaline pH values of 8.4 and 11.0 for 3.0 and 8.0 V, respectively.

519

Our experimental results were not able to produce a definitive trend or explanation for why some

520

experiments were acidic at the 2.5 cm sampling location while others were basic. Since the pH

521

continuum from the acidic anode to the alkaline cathode just 5.0 cm away is very steep

522

(especially with higher voltages), it is conceivable that variability in flow and/or mixing in the

523

inter-electrode space could contribute to the range of pH values observed. It is also feasible that

524

a high inter-electrode pH may arise when CO2 gas, present in the influent or generated from

525

organic carbon mineralization, is effervescently released through the gas vents at the acidic

526

anodes, and thus no longer has the buffering capacity provided by carbonic acid.

527

The sessile CB1190 counts for bioaugmented columns at 0 V and 3.0 V were able to

528

maintain dense biofilms between the electrodes, measuring 3.4 x 107 and 2.1 x 106 cells/g,

529

respectively. The higher biofilm counts relative to the planktonic counts in this region between

530

the electrodes can be explained by biofilms generally having a greater ability to withstand pH

531

changes and short-lived reactive oxygen species.67 The aqueous conditions within the 8.0 V

532

experiment appear to have been too harsh to establish stable biofilm communities, such that

533

sessile counts were below LOD between the electrodes (and at 22.5 cm downstream) with

534

biofilm counts only being observed at the 12.5 cm “sweet spot” reaching 2.3 x 106 cells/g (Figure

535

3 d). This becomes a disadvantage if biodegradation activity is dependent on newly dispersed

536

planktonic cells from biofilms as the primary source of active cells. Interestingly, there was a

537

substantial spike in sessile cell abundance at 12.5 cm downstream experienced in both the 3.0

538

and 8.0 V electro-bioreactors, reaching 107-108 cells/g. This would lend further support to our

539

“sweet spot” hypothesis for optimum bacterial growth. Based upon the consistency of the

540

location of peak sessile cell counts just downstream of the electrodes, it appears that biofilm

541

formation is being used as a strategy of colonization in a nutrient-dense (1,4-dioxane carbon

542

source), oxygen-enriched, and circumneutral pH region (usually pH 6.4 ± 0.6), where dispersion 21 ACS Paragon Plus Environment

Environmental Science & Technology

Page 22 of 28

543

of actively metabolizing planktonic cells can then occur, providing the majority of observable

544

biodegradation.67

545

Technological

Implications.

Our

results

demonstrate

that

the

coupling

of

546

electrochemical oxidation with aerobic biodegradation is an effective, synergistic approach for

547

the treatment of waters contaminated with 1,4-dioxane, and may provide an effective solution to

548

the problems associated with co-occurring inhibitors. We did not experience clogging in any of

549

the experiments, indicating that bioaugmentation of aquifers with CB1190 is a viable strategy.

550

Successful establishment of CB1190 biofilm is expected to be possible in a range of flow

551

regimes. Although tests at different flow rates were outside the scope of this study, other research

552

results have shown that bacterial biofilm thickness and survivability did not change significantly

553

with altered flow rates.57,68 In the absence of a co-contaminant, where the enhancement is mainly

554

based on oxygen generation, low voltages (i.e., 3.0 V) slightly above the oxygen evolution

555

potential of the electrode are preferable to avoid extreme pH and redox conditions unfavorable

556

for microbial growth, and may be a viable strategy to limit DBP formation. Furthermore, lower

557

voltages are preferable due to longer electrode service life, reduced power cost, and more

558

uniform flow with less gas bubbles.37,54,55

559

When microbially-inhibiting co-contaminants such as TCE are present, more electrodes

560

may be required in order to mineralize or transform the additional contaminants into less toxic or

561

more readily biodegradable intermediates.33,69 If the chlorinated co-contaminants are not fully

562

removed during electrolytic treatment, a subsequent reductive treatment step may be effective,

563

which could also aid in the removal of any generated DBPs.70

564

This study provides convincing evidence that 1,4-dioxane metabolism by CB1190 can be

565

electrochemically enhanced despite the production of strong oxidants at the anode. Our data

566

suggest that microbial abundance is lowest between the electrodes, likely due to destructive

567

effects of short-lived chemical oxidants, and highest just downstream of the trailing cathode (near

568

12.5 cm downstream of the anode) where dissolved oxygen concentrations stimulate microbial

569

metabolism. Thus, microbial populations are able to thrive downstream of the electrodes, and the

570

generation of strong oxidants (e.g., •OH) can provide significant concomitant benefits of

571

oxidizing recalcitrant and/or toxic co-pollutants in addition to 1,4-dioxane.

572

For technology implementation, specific aquifer conditions (e.g., contaminant

573

concentrations, water quality parameters, soil composition, and indigenous microbial 22 ACS Paragon Plus Environment

Page 23 of 28

Environmental Science & Technology

574

communities) or wastewater composition need to be taken into consideration and tested to

575

validate contaminant degradation efficiencies. These preliminary test results and specific

576

treatment targets would guide decisions regarding the number of sequential electrodes required

577

(more electrode surface area for more contaminant mass removal), but our results suggest that

578

sufficient spacing between electrode pairs should be arranged to promote maximum microbial

579

activity in the favorable downstream conditions. It is conceivable that additional synergistic

580

mechanisms could also be promoted, such as stimulation of other intrinsic microbes capable of

581

metabolizing transformation products and co-contaminant parent compounds71 or electrolytic

582

transformation

of

a

27,33,72-74

persistent

parent

compound

into

more

readily

biodegradable

583

intermediates.

Although other mixed contaminants waters were not explored in this

584

study, the capability of this technology being effective in a flow-through system could lend itself

585

to feasible treatment applications for landfill leachate, domestic wastewater, and industrial

586

effluent as well.69,75 The joint benefits of having tunable electrolysis to degrade recalcitrant

587

pollutants while simultaneously supporting intrinsic or augmented contaminant-degraders may be

588

one innovative approach needed to overcome the technological and cost limitations faced when

589

treating waters with mixed, persistent contaminants.

590 591 592 593

AUTHOR INFORMATION

594

Corresponding Author* E-mail: [email protected]. Phone: +1-970-491-8880. Fax:

595

+1-970-491-8224.

596

Notes: The authors declare no competing financial interest.

597 598 599

ACKNOWLEDGMENTS

600

Funding for this work was provided by The Chemours Company (to J.B.), E. I. du Pont de

601

Nemours and Company (to J.B. and contract no. MA-03653-13 to S.M.) and The Dow Chemical

602

Company (contract no. 244633 to S.M.). We thank Maria Irianni-Renno for assistance with ATP

603

analysis, and Michelle Myers and Shu Zhang for assisting with DNA extractions.

604 23 ACS Paragon Plus Environment

Environmental Science & Technology

Page 24 of 28

605

ASSOCIATED CONTENT

606

Supporting Information. The Supporting Information is available free of charge on the ACS

607

Publications website at DOI: …

608

It includes schematics and photos of the experimental design, details on analytical procedures

609

and CB1190 inoculation procedures, and calculations used to determine flow-through

610

degradation rates and instrumental uncertainty. Additional plots and tables show TCE removal,

611

DO measurements, and pH values along the column reactor path.

612 613 614

REFERENCES

615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647

(1) Mohr, T. K.; Stickney, J. A.; DiGuiseppi, W. H. Environmental investigation and remediation: 1,4dioxane and other solvent stabilizers. CRC Press: Boca Raton, FL, 2010. (2) USEPA. United States Environmental Protection Agency. Technical fact sheet--1,4-dioxane. Office of solid waste and emergency response. 2014, EPA-505-F-14-011. (3) Adamson, D. T.; Mahendra, S.; Walker, K. L.; Rauch, S. R.; Sengupta, S.; Newell, C. J. A multisite survey to identify the scale of the 1,4-dioxane problem at contaminated groundwater sites. Environmental Science & Technology Letters 2014, 1, 254-258. (4) Chiang, S. Y. D.; Mora, R.; Diguiseppi, W. H.; Davis, G.; Sublette, K.; Gedalanga, P.; Mahendra, S. Characterizing the intrinsic bioremediation potential of 1,4-dioxane and trichloroethene using innovative environmental diagnostic tools. Journal of Environmental Monitoring 2012, 14, 2317-2326. (5) Anderson, R. H.; Anderson, J. K.; Bower, P. A. Co-occurrence of 1,4-dioxane with trichloroethylene in chlorinated solvent groundwater plumes at us air force installations: Fact or fiction. Integrated Environmental Assessment and Management 2012, 8, 731-737. (6) Zenker, M. J.; Borden, R. C.; Barlaz, M. A. Occurrence and treatment of 1,4-dioxane in aqueous environments. Environmental Engineering Science 2003, 20, 423-432. (7) Isaka, K.; Udagawa, M.; Sei, K.; Ike, M. Pilot test of biological removal of 1,4-dioxane from a chemical factory wastewater by gel carrier entrapping Afipia sp. Strain d1. Journal of Hazardous Materials 2016, 304, 251-258. (8) Han, T. H.; Han, J. S.; So, M. H.; Seo, J. W.; Ahn, C. M.; Min, D. H.; Yoo, Y. S.; Cha, D. K.; Kim, C. G. The removal of 1,4-dioxane from polyester manufacturing process wastewater using an up-flow biological aerated filter (UBAF) packed with tire chips. Journal of Environmental Science and Health Part a-Toxic/Hazardous Substances & Environmental Engineering 2012, 47, 117-129. (9) Stefan, M. I.; Bolton, J. R. Mechanism of the degradation of 1,4-dioxane in dilute aqueous solution using the UV hydrogen peroxide process. Environmental Science & Technology 1998, 32, 1588-1595. (10) Coleman, H. M.; Vimonses, V.; Leslie, G.; Amal, R. Degradation of 1,4-dioxane in water using TiO2 based photocatalytic and H2O2/UV processes. Journal of Hazardous Materials 2007, 146, 496-501. (11) Maurino, V.; Calza, P.; Minero, C.; Pelizzetti, E.; Vincenti, M. Light-assisted 1,4-dioxane degradation. Chemosphere 1997, 35, 2675-2688. (12) Canizares, P.; Paz, R.; Saez, C.; Rodrigo, M. A. Costs of the electrochemical oxidation of wastewaters: A comparison with ozonation and fenton oxidation processes. Journal of Environmental Management 2009, 90, 410-420. (13) Mahendra, S.; Alvarez-Cohen, L. Kinetics of 1,4-dioxane biodegradation by monooxygenaseexpressing bacteria. Environmental Science & Technology 2006, 40, 5435-5442.

24 ACS Paragon Plus Environment

Page 25 of 28

648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697

Environmental Science & Technology

(14) Vainberg, S.; McClay, K.; Masuda, H.; Root, D.; Condee, C.; Zylstra, G. J.; Steffan, R. J. Biodegradation of ether pollutants by Pseudonocardia sp. strain ENV478. Applied and Environmental Microbiology 2006, 72, 5218-5224. (15) Lan, R. S.; Smith, C. A.; Hyman, M. R. Oxidation of cyclic ethers by alkane-grown Mycobacterium vaccae JOB5. Remediation Journal 2013, 23, 23-42. (16) Nakamiya, K.; Hashimoto, S.; Ito, H.; Edmonds, J. S.; Morita, M. Degradation of 1,4-dioxane and cyclic ethers by an isolated fungus. Applied and Environmental Microbiology 2005, 71, 1254-1258. (17) Parales, R. E.; Adamus, J. E.; White, N.; May, H. D. Degradation of 1,4-dioxane by an actinomycete in pure culture. Applied and Environmental Microbiology 1994, 60, 4527-4530. (18) Mahendra, S.; Alvarez-Cohen, L. Pseudonocardia dioxanivorans sp nov., a novel actinomycete that grows on 1,4-dioxane. International Journal of Systematic and Evolutionary Microbiology 2005, 55, 593598. (19) Sekar, R.; DiChristina, T. J. Microbially driven fenton reaction for degradation of the widespread environmental contaminant 1,4-dioxane. Environmental Science & Technology 2014, 48, 12858-12867. (20) Mahendra, S.; Grostern, A.; Alvarez-Cohen, L. The impact of chlorinated solvent co-contaminants on the biodegradation kinetics of 1,4-dioxane. Chemosphere 2013, 91, 88-92. (21) Hand, S.; Wang, B. X.; Chu, K. H. Biodegradation of 1,4-dioxane: Effects of enzyme inducers and trichloroethylene. Science of the Total Environment 2015, 520, 154-159. (22) Zhang, S.; Gedalanga, P. B.; Mahendra, S. Biodegradation kinetics of 1,4-dioxane in chlorinated solvent mixtures. Environmental Science & Technology 2016, 50, 9599–9607. (23) Gedalanga, P. B.; Pornwongthong, P.; Mora, R.; Chiang, S.-Y. D.; Baldwin, B.; Ogles, D.; Mahendra, S. Identification of biomarker genes to predict biodegradation of 1,4-dioxane. Applied and Environmental Microbiology 2014, 80, 3209-3218. (24) Adamson, D. T.; Anderson, R. H.; Mahendra, S.; Newell, C. J. Evidence of 1,4-dioxane attenuation at groundwater sites contaminated with chlorinated solvents and 1,4-dioxane. Environmental Science & Technology 2015, 49, 6510-6518. (25) Gedalanga, P.; Madison, A.; Miao, Y. R.; Richards, T.; Hatton, J.; DiGuiseppi, W. H.; Wilson, J.; Mahendra, S. A multiple lines of evidence framework to evaluate intrinsic biodegradation of 1,4-dioxane. Remediation Journal 2016, 27, 93-114. (26) Li, M.; van Orden, E. T.; DeVries, D. J.; Xiong, Z.; Hinchee, R.; Alvarez, P. J. Bench-scale biodegradation tests to assess natural attenuation potential of 1,4-dioxane at three sites in california. Biodegradation 2015, 26, 39-50. (27) Chen, G.; Betterton, E. A.; Arnold, R. G. Electrolytic oxidation of trichloroethylene using a ceramic anode. Journal of Applied Electrochemistry 1999, 29, 961-970. (28) Sale, T.; Petersen, M.; Gilbert, D. Electrically induced redox barriers for treatment of groundwater; ESTCP Final Report CU-0112. U.S. Department of Defense: 2005. (29) Petersen, M. A.; Sale, T. C.; Reardon, K. F. Electrolytic trichloroethene degradation using mixed metal oxide coated titanium mesh electrodes. Chemosphere 2007, 67, 1573-1581. (30) Choi, J. Y.; Lee, Y. J.; Shin, J.; Yang, J. W. Anodic oxidation of 1,4-dioxane on boron-doped diamond electrodes for wastewater treatment. Journal of Hazardous Materials 2010, 179 (1-3), 762-768. (31) De Clercq, J.; Van de Steene, E.; Verbeken, K.; Verhaege, M. Electrochemical oxidation of 1,4dioxane at boron-doped diamond electrode. Journal of Chemical Technology and Biotechnology 2010, 85, 1162-1167. (32) Jasmann, J. R.; Borch, T.; Sale, T. C.; Blotevogel, J. Advanced electrochemical oxidation of 1,4dioxane via dark catalysis by novel titanium dioxide (TiO2) pellets. Environmental Science & Technology 2016, 50, 8817-8826. (33) Adams, C. D.; Scanlan, P. A.; Secrist, N. D. Oxidation and biodegradability enhancement of 1,4dioxane using hydrogen-peroxide and ozone. Environmental Science & Technology 1994, 28, 1812-1818. (34) Suh, J. H.; Mohseni, M. A study on the relationship between biodegradability enhancement and oxidation of 1,4-dioxane using ozone and hydrogen peroxide. Water Research 2004, 38, 2596-2604. 25 ACS Paragon Plus Environment

Environmental Science & Technology

698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748

(35) Carter, K. E.; Farrell, J. Electrochemical oxidation of trichloroethylene using boron-doped diamond film electrodes. Environmental Science & Technology 2009, 43, (21), 8350-8354. (36) Klecka, G. M.; Gonsior, S. J. Removal of 1,4-dioxane from waste-water. Journal of Hazardous Materials 1986, 13, 161-168. (37) Radjenovic, J.; Sedlak, D. L. Challenges and opportunities for electrochemical processes as nextgeneration technologies for the treatment of contaminated water. Environmental Science & Technology 2015, 49, 11292-11302. (38) Park, H.; Vecitis, C. D.; Hoffmann, M. R. Electrochemical water splitting coupled with organic compound oxidation: The role of active chlorine species. The Journal of Physical Chemistry C 2009, 113, 7935-7945. (39) Deborde, M.; Von Gunten, U. Reactions of chlorine with inorganic and organic compounds during water treatment - kinetics and mechanisms: A critical review. Water Research 2008, 42, 13-51. (40) Cho, K.; Hoffmann, M. R. Urea degradation by electrochemically generated reactive chlorine species: Products and reaction pathways. Environmental Science & Technology 2014, 48, 11504-11511. (41) Martinez-Huitle, C. A.; Andrade, L. S. Electrocatalysis in wastewater treatment: Recent mechanism advances. Quimica Nova 2011, 34, 850-858. (42) Sun, M.; Reible, D. D.; Lowry, G. V.; Gregory, K. B. Effect of applied voltage, initial concentration, and natural organic matter on sequential reduction/oxidation of nitrobenzene by graphite electrodes. Environmental Science & Technology 2012, 46, 6174-6181. (43) Sun, M.; Yan, F.; Zhang, R. L.; Reible, D. D.; Lowry, G. V.; Gregory, K. B. Redox control and hydrogen production in sediment caps using carbon cloth electrodes. Environmental Science & Technology 2010, 44, 8209-8215. (44) Fierro, S.; Nagel, T.; Baltruschat, H.; Comninellis, C. Investigation of the oxygen evolution reaction on Ti/IrO2 electrodes using isotope labelling and on-line mass spectrometry. Electrochemistry Communications 2007, 9, (8), 1969-1974. (45) Comninellis, C.; Kapalka, A.; Malato, S.; Parsons, S. A.; Poulios, L.; Mantzavinos, D. Advanced oxidation processes for water treatment: Advances and trends for R&D. Journal of Chemical Technology and Biotechnology 2008, 83, 769-776. (46) Bagastyo, A. Y.; Radjenovic, J.; Mu, Y.; Rozendal, R. A.; Batstone, D. J.; Rabaey, K. Electrochemical oxidation of reverse osmosis concentrate on mixed metal oxide (MMO) titanium coated electrodes. Water Research 2011, 45, 4951-4959. (47) Rodgers, J. D.; Jedral, W.; Bunce, N. I. Electrochemical oxidation of chlorinated phenols. Environmental Science & Technology 1999, 33, 1453-1457. (48) Xie, W.; Yuan, S.; Mao, X.; Hu, W.; Liao, P.; Tong, M.; Alshawabkeh, A. N. Electrocatalytic activity of Pd-loaded Ti/ TiO2 nanotubes cathode for TCE reduction in groundwater. Water Research 2013, 47, 3573-3582. (49) Sale, T.; Olson, M.; Gilbert, D.; Petersen, M. Field demonstration/validation of electrolytic barriers for energetic compounds at Pueblo Chemical Depot. ESTCP ER-0519. U.S. Department of Defense: 2010. (50) Mahendra, S.; Petzold, C. J.; Baidoo, E. E.; Keasling, J. D.; Alvarez-Cohen, L. Identification of the intermediates of in vivo oxidation of 1,4-dioxane by monooxygenase-containing bacteria. Environmental Science & Technology 2007, 41, 7330-7336. (51) Shah, A.; Jorne, J. Mass-transfer under combined gas evolution and forced-convection. Journal of the Electrochemical Society 1989, 136, 153-158. (52) Petersen, M. A.; Reardon, K. F. Effect of gas evolution on mixing and conversion in a flow-through electrochemical reactor. AICHE Journal 2009, 55, 2468-2476. (53) Cabiscol, E.; Tamarit, J.; Ros, J. Oxidative stress in bacteria and protein damage by reactive oxygen species. International Microbiology 2010, 3, 3-8. (54) Schaefer, C. E.; Andaya, C.; Urtiaga, A. Assessment of disinfection and by-product formation during electrochemical treatment of surface water using a Ti/IrO2 anode. Chemical Engineering Journal 2015, 264, 411-416. 26 ACS Paragon Plus Environment

Page 26 of 28

Page 27 of 28

749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798

Environmental Science & Technology

(55) Chaplin, B. P. Critical review of electrochemical advanced oxidation processes for water treatment applications. Environmental Science-Processes & Impacts 2014, 16, 1182-1203. (56) Sercu, B.; Jones, A. D. G.; Wu, C. H.; Escobar, M. H.; Serlin, C. L.; Knapp, T. A.; Andersen, G. L.; Holden, P. A. The Influence of In Situ Chemical Oxidation on Microbial Community Composition in Groundwater Contaminated with Chlorinated Solvents. Microbial Ecolology 2013, 65, 39-49. (57) Stewart, P. S. Mini-review: Convection around biofilms. Biofouling 2012, 28, 187-198. (58) Donaghue, A.; Chaplin, B. P. Effect of select organic compounds on perchlorate formation at boron-doped diamond film anodes. Environmental Science & Technology 2013, 47, 12391-12399. (59) Mascia, M.; Vacca, A.; Palmas, S.; Polcaro, A. M. Kinetics of the electrochemical oxidation of organic compounds at BDD anodes: Modelling of surface reactions. Journal of Applied Electrochemistry 2007, 37, 71-76. (60) Kapalka, A.; Fóti, G.; Comninellis, C. The importance of electrode material in environmental electrochemistry: Formation and reactivity of free hydroxyl radicals on boron-doped diamond electrodes. Electrochimica Acta 2009, 54, 2018-2023. (61) Gibbs, P. A.; Seviour, R. J. Does the agitation rate and/or oxygen saturation influence exopolysaccharide production by Aureobasidium pullulans in batch culture? Applied Microbiology and Biotechnology 1996, 46 (5-6), 503-510. (62) Uppuluri, P.; Chaturvedi, A. K.; Srinivasan, A.; Banerjee, M.; Ramasubramaniam, A. K.; Köhler, J. R.; Kadosh, D.; Lopez-Ribot, J. L. Dispersion as an important step in the Candida albicans biofilm developmental cycle. PLoS Pathog. 2010, 6, e1000828. (63) LaFleur, M. D.; Kumamoto, C. A.; Lewis, K. Candida albicans biofilms produce antifungaltolerant persister cells. Antimicrobial Agents and Chemotherapy 2006, 50, 3839-3846. (64) Pareilleux, A.; Sicard, N. Lethal effects of electric current on Escherichia coli. Applied Microbiology 1970, 19, 421. (65) Zaky, A. M.; Chaplin, B. P. Porous substoichiometric TiO2 anodes as reactive electrochemical membranes for water treatment. Environmental Science & Technology 2013, 47, 6554-6563. (66) Manefield, M.; Lee, M.; Koenig, J. The Nature and Relevance of Solvent Stress in Microbes and Mechanisms of Tolerance. In: Chénard C., Lauro F. (Eds.) Microbial Ecology of Extreme Environments. Springer, Cham, 2017. ISBN 978-3-319-51686-8. (67) Jefferson, K. K. What drives bacteria to produce a biofilm? Fems Microbiology Letters 2004, 236, 163-173. (68) Bishop, P.; Gibbs, J.; Cunningham, B. Relationship between concentration and hydrodynamic boundary layers over biofilms. Environmental Technology 1997, 18, 375-385. (69) Chu, Y. Y.; Zhu, M. H.; Liu, C. Electrochemical treatment of biotreated landfill leachate using a porous carbon nanotube-containing cathode: Performance, toxicity reduction, and biodegradability enhancement. Environmental Engineering Science 2015, 32, 445-450. (70) Schaefer, C. E.; Andaya, C.; Burant, A.; Condee, C. W.; Urtiaga, A.; Strathmann, T. J.; Higgins, C. P. Electrochemical treatment of perfluorooctanoic acid and perfluorooctane sulfonate: Insights into mechanisms and application to groundwater treatment. Chemical Engineering Journal 2017, 317, 424432. (71) Arp, D. J.; Yeager, C. M.; Hyman, M. R. Molecular and cellular fundamentals of aerobic cometabolism of trichloroethylene. Biodegradation 2001, 12, 81-103. (72) Tseng, N.; Wang, N.; Szostek, B.; Mahendra, S. Biotransformation of 6:2 fluorotelomer alcohol (6:2 FTOH) by a wood-rotting fungus. Environmental Science & Technology 2014, 48, 4012-4020. (73) Barndok, H.; Hermosilla, D.; Cortijo, L.; Torres, E.; Blanco, A. Electrooxidation of industrial wastewater containing 1,4-dioxane in the presence of different salts. Environmental Science and Pollution Research 2014, 21, 5701-5712. (74) Grostern, A.; Sales, C. M.; Zhuang, W. Q.; Erbilgin, O.; Alvarez-Cohen, L. Glyoxylate metabolism is a key feature of the metabolic degradation of 1,4-dioxane by Pseudonocardia dioxanivorans strain CB1190. Applied and Environmental Microbiology 2012, 78, 3298-3308. 27 ACS Paragon Plus Environment

Environmental Science & Technology

799 800

(75) Lenker, C.; Harclerode, M.; Aragona, K.; Fisher, A.; Jasmann, J.; Hadley, P. W. Integrating groundwater conservation and reuse into remediation projects. Remediation Journal 2014, 24, 11-27.

28 ACS Paragon Plus Environment

Page 28 of 28