Thermodynamic Properties of Mixtures Containing Ionic Liquids

Laura Sprunger, Michael Clark, William E. AcreeJr., and Michael H. Abraham. Journal of ... M. S. Beasley , M. Tylinski , Y. Z. Chua , C. Schick , M. D...
7 downloads 0 Views 115KB Size
142

J. Chem. Eng. Data 2005, 50, 142-148

Thermodynamic Properties of Mixtures Containing Ionic Liquids. Activity Coefficients of Ethers and Alcohols in 1-Methyl-3-Ethyl-Imidazolium Bis(Trifluoromethyl-sulfonyl) Imide Using the Transpiration Method Tatiana V. Vasiltsova, Sergey P. Verevkin, Eckard Bich, and Andreas Heintz* Department of Physical Chemistry, University of Rostock, Hermannstrasse 14, D-18051 Rostock, Germany

Rafal Bogel-Lukasik and Urszula Domanska Warsaw University of Technology, Faculty of Chemistry, Physical Chemistry Division, Warsaw, Poland

Vapor-liquid equilibria of binary mixtures containing high-boiling solutes methoxy-benzene, (hydroxymethyl)-benzene, 1,2-ethanediol, and 1,4-butanediol and ionic liquid [EMIM][NTf2] were studied by using the transpiration method. VLE measurements were carried out over the whole concentration range at different temperatures between 298 K and 363 K. Activity coefficients γi of these solvents in the ionic liquid have been determined from these data and are described formally by using the NRTL equation. In addition, vapor pressures of pure solutes methoxy-benzene, (hydroxymethyl)-benzene, 1,2-ethanediol, and 1,4-butanediol have been measured as a function of temperature, and their enthalpies of vaporization have been obtained.

Introduction The use of ionic liquids (ILs) as solvents for a broad range of chemical processes is potentially one of the most significant developments of the past decade. In contrast to molten salts, which have very high melting points and are highly corrosive, ionic liquids are organic salts that are liquids under ambient conditions. Ionic liquids are thermally stable and odorless, and many are unaffected by moisture. They have no detectable vapor pressure and are immiscible or partially miscible with saturated hydrocarbon solvents, dialkyl ethers, and water (which makes the extraction of organic products simple and efficient). Because of this combination of properties, ionic liquids are candidates for recyclable “green” solvents. Knowledge of specific properties will provide fundamental insight into the unique behavior of this novel class of solvents. A diverse range of ionic liquids is commercially available.7 However, little information is available on their physical properties. This work continues our study of the thermodynamic properties of mixtures of solutes in ILs.1-5 Activity coefficients covering the whole range of composition for mixtures containing high-boiling compounds (such as aldehydes and ketones) and ionic liquids were reported recently.6 With the present work, we continue to fill the gap of information on this class of ionic liquid mixtures. We have performed measurements of activity coefficient γi of four solutes in the ionic liquid 1-methyl-3-ethylimidazolium bis(trifluoromethyl-sulfonyl) imide [EMIM][NTf2]:

* Corresponding rostock.de.

author.

E-mail:

[email protected]

A series of mixtures of the solutes methoxy-benzene, (hydroxymethyl)-benzene, 1,2-ethanediol, and 1,4-butanediol with [EMIM][NTf2], have been studied over the temperature range of (298 to 363) K. Vapor pressures of the pure individual alcohols and ether, required for the calculation of the activity coefficients, as well as enthalpies of vaporization of these compounds have been obtained by using the transpiration method (Table 1). Experimental Section Materials. The samples of methoxybenzene (or anisol), (hydroxymethyl)-benzene (or benzyl alcohol), 1,2-ethanediol, and 1,4-butanediol were purchased from Aldrich and Merck and dried and purified by fractional distillation. The degree of purity was controlled using a Hewlett-Packard gas chromatograph 5890 series II equipped with a flameionization detector, autosampler, and Hewlett-Packard 3390A integrator. The carrier gas (nitrogen) flow was 0.726 dm3‚min-1. An HP-5 capillary column (stationary phase cross-linked 5% PH ME silicone) was used with a column length of 30 m, an inside diameter of 0.32 mm, and a film thickness of 0.25 m. The standard temperature program of the GC was T ) 333 K for 3 min followed by a heating rate of 10 K‚min-1 to T ) 523 K. No impurities (greater than mass fraction 0.0005) could be detected in the samples used for the investigation. The ionic liquid [EMIM][NTf2] was synthesized according to the literature procedure.8 Before use, the sample was dissolved in excess methanol and filtered. Then it was subjected to vacuum evaporation at 333 K over 24 h to remove possible traces of solvents and moisture. Samples of ionic liquid used in the experiment have been checked regularly concerning water content using Karl Fischer titration. In all cases, the content of water was less than 100 ppm. All samples have been stored in a dry atmosphere of N2 before use.

10.1021/je0497799 CCC: $30.25 © 2005 American Chemical Society Published on Web 12/24/2004

Journal of Chemical and Engineering Data, Vol. 50, No. 1, 2005 143 Table 1. Results for the Vapor Pressure p and ∆gl Hm of Pure Compounds Obtained by the Transpiration Method T K

278.3 281.3 284.3 287.3 290.3 293.3

282.2 285.2 288.2 291.2 294.1 297.2 300.2 303.2

308.2 313.2 328.1 303.2 323.2 326.2 306.2

329.2 332.3 335.2 338.2 341.2 343.2 346.3

m

VN2

mg

dm3

4.88 4.47 4.85 5.49 5.57 5.21

0.89 0.98 1.00 1.35 1.27 1.02 1.19 1.08

1.24 2.40 1.63 2.17 2.21 1.65 1.98

0.48 0.79 1.12 0.90 0.82 0.93 0.95

0.96 0.70 0.61 0.56 0.46 0.35

p

pexptl - pcalcd

∆gl Hm

Pa

kJ‚mol-1

Pa

T K

m

VN2

p

pexptl - pcalcd

∆gl Hm

mg

dm3

Pa

Pa

kJ‚mol-1

-10.9 8.9 0.8 -10.5 5.1 10.9

46.70 46.52 46.34 46.09 45.90 45.71

0.6 -0.5 -0.2 -1.1 0.5 -1.2 0.7

65.00 64.80 64.60 64.40 64.20 64.00 63.81

Methoxy-benzene, ∆gl Hm(298.15 K) ) (46.59 ( 0.22) kJ‚mol-1 eq 2: a ) 269.809 J‚mol-1K-1, b ) -65 160.559 J‚mol-1, ∆gl Cp ) 62.3 J‚mol-1K-1 122.0 0.1 47.83 296.3 4.90 0.28 410.9 152.4 0.6 47.64 299.3 5.75 0.26 518.8 189.3 1.1 47.45 302.2 6.24 0.24 610.6 231.7 -0.2 47.26 306.2 6.38 0.19 765.0 285.1 0.5 47.08 309.2 8.62 0.21 929.2 345.2 -2.0 46.89 312.3 6.21 0.13 1113.9

7.49 6.08 4.40 4.46 3.23 2.02 1.74 1.25

(Hydroxymethyl)-benzene, ∆gl Hm(298.15 K) ) (65.46 ( 0.38) kJ‚mol-1 eq 2: a ) 307.387 J‚mol-1K-1, b ) -85 350.413 J‚mol-1, ∆gl Cp ) 66.7 J‚mol-1K-1 2.72 -0.1 66.53 305.2 1.29 1.23 23.77 3.68 -0.1 66.33 308.1 0.95 0.75 28.95 5.16 0.1 66.13 311.2 0.88 0.53 37.79 6.88 0.2 65.93 314.1 1.16 0.57 46.68 8.90 0.1 65.74 317.1 1.25 0.46 60.77 11.48 -0.1 65.53 320.1 1.06 0.32 74.55 15.49 0.4 65.33 323.0 0.84 0.20 94.70 19.59 0.0 65.13

1.86 2.36 0.52 4.79 1.04 0.62 3.44

1,2-Ethanediol, ∆gl Hm(298.15 K) ) (65.40 ( 0.32) kJ‚mol-1 eq 2: a ) 289.087 J‚mol-1K-1, b ) -80 163.333 J‚mol-1, ∆gl Cp ) 49.5 J‚mol-1K-1 26.39 -0.3 64.91 310.2 1.97 2.51 31.07 40.27 0.3 64.66 316.2 1.81 1.45 49.50 124.4 1.7 63.92 318.2 1.88 1.24 59.97 17.99 0.4 65.16 320.2 1.96 1.14 67.97 84.64 -1.3 64.17 331.2 2.09 0.54 152.3 105.3 -1.7 64.02 333.2 3.75 0.83 179.2 22.75 0.1 65.01 336.2 1.98 0.36 216.4

-0.4 -1.1 0.9 -0.7 -0.5 3.6 0.9

64.81 64.51 64.41 64.32 63.77 63.67 63.52

0.94 1.13 1.25 0.76 0.57 0.54 0.43

1,4-Butanediol, ∆gl Hm(298.15 K) ) (78.95 ( 0.92) kJ‚mol-1 eq 2: a ) 325.131 J‚mol-1K-1, b ) -97 614.424 J‚mol-1, ∆gl Cp ) 62.6 J‚mol-1K-1 13.85 -0.9 77.01 348.2 1.21 0.48 69.52 18.99 -0.2 76.82 351.2 0.97 0.31 84.55 24.37 0.0 76.63 353.2 1.07 0.28 103.1 32.20 1.1 76.45 356.2 0.99 0.22 120.6 39.40 -0.1 76.26 358.3 0.93 0.18 142.1 47.54 1.4 76.13 361.2 0.91 0.15 167.1 59.71 1.1 75.94 363.2 1.03 0.15 189.0

1.8 -0.1 5.1 -1.1 0.8 -5.8 -9.3

75.82 75.63 75.51 75.32 75.19 75.01 74.88

Table 2. VLE in the System (Methoxy-benzene + [EMIM][NTf2]) T/K

x1

pexptl /Pa 1

pNRTL /Pa 1

γNRTL 1

ln γNRTL 1

T/K

x1

pexptl /Pa 1

pNRTL /Pa 1

γNRTL 1

ln γNRTL 1

298.6

0.000 0.200 0.377 0.569

0.00 155.51 261.75 345.76

0.00 152.46 267.95 363.70

1.591 1.521 1.420 1.278

0.464 0.419 0.351 0.245

298.6

0.679 0.796 0.920 1.000

431.62 430.15 496.64 500.11

403.51 436.23 469.12 500.11

1.188 1.096 1.020 1.000

0.172 0.091 0.019 0.000

303.6

0.000 0.174 0.232 0.493

0.00 192.98 285.00 529.33

0.00 204.81 268.59 509.11

1.812 1.748 1.719 1.535

0.594 0.558 0.542 0.429

303.6

0.661 0.783 0.917 1.000

580.89 640.17 670.31 673.07

606.63 641.01 650.40 673.07

1.364 1.216 1.053 1.000

0.311 0.195 0.052 0.000

308.6

0.000 0.146 0.185 0.642

0.00 247.23 341.20 753.94

0.00 259.38 320.78 805.51

2.140 1.986 1.945 1.406

0.761 0.686 0.665 0.341

308.6

0.764 0.914 1.000

875.72 913.59 892.11

847.19 860.04 892.11

1.243 1.054 1.000

0.217 0.053 0.000

313.6

0.000 0.118 0.143 0.370

0.00 312.06 414.76 892.65

0.00 335.48 395.21 826.05

2.724 2.409 2.351 1.895

1.002 0.879 0.855 0.639

313.6

0.621 0.740 0.911 1.000

1035.40 1159.89 1156.25 1178.31

1088.07 1138.35 1143.64 1178.31

1.486 1.306 1.065 1.000

0.396 0.267 0.063 0.000

318.6

0.000 0.088 0.108 0.303

0.00 395.31 465.41 1095.63

0.00 400.39 474.49 1015.30

3.455 2.952 2.859 2.174

1.240 1.083 1.050 0.776

318.6

0.598 0.713 0.907 1.000

1402.91 1607.42 1546.61 1543.31

1449.89 1526.47 1523.16 1543.31

1.572 1.387 1.088 1.000

0.452 0.327 0.084 0.000

323.6

0.000 0.059 0.076 0.239

0.00 492.44 558.03 1180.83

0.00 464.67 573.82 1269.14

4.648 3.960 3.792 2.644

1.536 1.376 1.333 0.972

323.6

0.572 0.686 0.904 1.000

1738.92 1925.27 1950.05 2004.25

1783.24 1839.40 1898.54 2004.25

1.555 1.338 1.048 1.000

0.441 0.291 0.047 0.000

Vapor Pressure Measurements of Pure-Component Systems. The vapor pressure and enthalpies of vaporization of alcohols and ether were determined using the method of transpiration in a saturated N2 stream and by applying the Clausius-Clapeyron equation. About 0.5 g of the sample was mixed with glass beads and placed in a thermostated U-shaped tube having a length of 20 cm and a diameter of 0.5 cm. Glass beads with a diameter of 1 mm provide a surface large enough for rapid vapor-liquid equilibration. At constant temperature ((0.1 K), a nitrogen stream was passed through the U tube, and the transported

amount of gaseous material was collected in a cooling trap. The flow rate of the nitrogen stream was measured using a soap bubble flowmeter and optimized to reach the saturation equilibrium of the transporting gas at each temperature under study. The flow rate of the nitrogen stream in the saturation tube should not be too slow in order to avoid the transport of material from the U tube by diffusion. However, the flow rate should be not too fast in order to reach the saturation of the nitrogen stream with a compound. We tested our apparatus at different carrier gas flow rates to check the lower boundary of the flow rate

144

Journal of Chemical and Engineering Data, Vol. 50, No. 1, 2005

Table 3. VLE in the System ((Hydroxymethyl)-benzene + [EMIM][NTf2]) T/K

x1

pexptl /Pa 1

pNRTL /Pa 1

γNRTL 1

ln γNRTL 1

T/K

x1

pexptl /Pa 1

pNRTL /Pa 1

γNRTL 1

ln γNRTL 1

298.6

0.000 0.049 0.154 0.270 0.395 0.482

0.00 1.14 2.87 3.89 5.83 7.16

0.00 1.14 2.76 4.21 5.80 6.99

1.937 1.586 1.217 1.060 0.998 0.984

0.661 0.461 0.196 0.058 -0.002 -0.016

298.6

0.549 0.670 0.851 0.963 1.000

8.19 10.42 11.66 13.90 13.02

7.93 9.72 12.48 14.17 14.72

0.982 0.986 0.996 1.000 1.000

-0.018 -0.014 -0.004 0.000 0.000

303.6

0.000 0.048 0.151 0.265 0.391 0.478

0.00 1.88 3.99 5.95 7.94 10.53

0.00 1.87 4.03 5.97 8.36 10.19

2.378 1.734 1.190 1.007 0.954 0.951

0.866 0.550 0.174 0.007 -0.047 -0.051

303.6

0.539 0.668 0.850 0.963 1.000

12.35 15.53 17.64 20.92 19.90

11.56 14.58 18.95 21.58 22.42

0.956 0.973 0.994 1.000 1.000

-0.045 -0.028 -0.006 0.000 0.000

308.6

0.000 0.046 0.144 0.183 0.259 0.473

0.00 2.57 5.94 6.62 8.70 17.38

0.00 2.53 5.85 6.97 9.11 15.94

1.974 1.547 1.148 1.074 0.993 0.949

0.680 0.436 0.138 0.071 -0.007 -0.052

308.6

0.527 0.550 0.666 0.849 0.963 1.000

18.62 20.43 21.93 29.06 31.65 30.25

17.85 18.65 22.99 29.94 34.14 35.47

0.954 0.957 0.973 0.994 1.000 1.000

-0.047 -0.044 -0.027 -0.006 0.000 0.000

313.6

0.000 0.045 0.134 0.252 0.382 0.467

0.00 4.07 8.67 13.06 18.55 21.99

0.00 4.05 8.70 13.35 18.69 22.55

2.392 1.820 1.299 1.059 0.981 0.968

0.872 0.599 0.261 0.057 -0.020 -0.032

313.6

0.514 0.663 0.848 0.963 1.000

27.38 32.80 42.30 45.19 45.36

24.85 32.40 42.11 48.05 49.93

0.967 0.978 0.995 1.000 1.000

-0.033 -0.022 -0.005 0.000 0.000

318.6

0.000 0.042 0.123 0.245 0.376 0.459

0.00 5.82 13.13 19.94 27.73 30.21

0.00 5.84 12.89 20.47 28.28 33.52

2.393 1.927 1.445 1.148 1.034 1.005

0.872 0.656 0.368 0.138 0.033 0.005

318.6

0.498 0.540 0.660 0.846 0.963 1.000

40.20 42.25 48.14 59.51 67.53 67.17

36.13 39.02 47.49 61.31 69.96 72.67

0.998 0.993 0.990 0.997 1.000 1.000

-0.002 -0.007 -0.010 -0.003 0.000 0.000

323.6

0.000 0.039 0.112 0.371 0.448 0.480

0.00 8.71 18.05 43.54 48.51 56.58

0.00 8.35 19.37 43.57 50.05 52.83

2.445 2.105 1.687 1.142 1.087 1.070

0.894 0.744 0.523 0.133 0.083 0.067

323.6

0.535 0.655 0.844 0.962 1.000

60.97 68.57 83.95 96.10 98.27

57.60 68.59 86.93 98.98 102.84

1.047 1.018 1.002 1.000 1.000

0.046 0.018 0.002 0.000 0.000

Table 4. VLE in the System (1,2-Ethanediol + [EMIM][NTf2]) T/K

x1

pexptl /Pa 1

pNRTL /Pa 1

γNRTL 1

ln γNRTL 1

T/K

x1

pexptl /Pa 1

pNRTL /Pa 1

γNRTL 1

ln γNRTL 1

339.6

0.000 0.133 0.294 0.436 0.545

0.00 87.93 176.04 239.12 253.85

0.00 89.17 176.87 227.81 249.09

2.672 2.534 2.268 1.971 1.723

0.983 0.930 0.819 0.679 0.544

339.6

0.629 0.713 0.860 0.951 1.000

246.26 249.64 251.50 261.38 273.38

255.90 256.56 252.30 256.14 265.22

1.535 1.357 1.107 1.016 1.000

0.428 0.305 0.101 0.015 0.000

343.6

0.000 0.128 0.283 0.413 0.522

0.00 115.35 244.43 304.44 306.08

0.00 120.23 230.92 291.27 319.86

2.857 2.619 2.276 1.964 1.707

1.050 0.963 0.822 0.675 0.535

343.6

0.596 0.612 0.848 0.948 1.000

332.24 320.06 331.62 353.03 357.00

329.87 331.20 335.44 345.03 358.95

1.541 1.507 1.102 1.014 1.000

0.433 0.410 0.097 0.014 0.000

348.6

0.000 0.122 0.268 0.367 0.384

0.00 154.14 342.76 439.70 434.78

0.00 164.79 326.92 407.71 418.76

2.851 2.701 2.437 2.216 2.176

1.048 0.994 0.891 0.796 0.777

348.6

0.491 0.552 0.832 0.944 1.000

455.91 460.36 452.64 512.00 494.08

470.77 487.26 481.89 483.19 501.13

1.914 1.761 1.155 1.021 1.000

0.649 0.566 0.144 0.021 0.000

353.6

0.000 0.115 0.251 0.348 0.455

0.00 218.76 494.27 605.80 618.30

0.00 236.00 454.79 563.64 640.17

3.315 3.063 2.703 2.423 2.101

1.199 1.119 0.994 0.885 0.742

353.6

0.494 0.813 0.940 1.000

637.20 604.61 681.03 677.55

656.76 648.42 644.33 669.13

1.985 1.192 1.025 1.000

0.686 0.175 0.025 0.000

358.6

0.000 0.108 0.235 0.305 0.416

0.00 302.27 637.36 817.24 880.08

0.00 322.12 619.89 742.94 873.70

3.752 3.467 3.072 2.833 2.441

1.322 1.243 1.122 1.041 0.892

358.6

0.423 0.790 0.936 1.000

845.16 806.38 872.85 921.01

879.21 869.36 832.00 860.09

2.417 1.279 1.034 1.000

0.882 0.246 0.033 0.000

363.6

0.000 0.101 0.219 0.261 0.345

0.00 380.66 960.47 1065.44 1125.28

0.00 433.76 846.76 965.14 1154.06

3.792 3.547 3.198 3.061 2.774

1.333 1.266 1.163 1.119 1.020

363.6

0.376 0.762 0.931 1.000

1167.75 1169.93 1221.86 1241.41

1208.72 1263.69 1170.98 1206.35

2.662 1.374 1.042 1.000

0.979 0.318 0.042 0.000

at which the contribution of the vapor condensed in the trap by diffusion becomes comparable to that transpired. In our apparatus, the contribution due to diffusion was negligible at a flow rate up to 6.6 cm3‚min-1. The upper

limit for our apparatus where the flow of nitrogen could already disturb the equilibration was at a flow rate of 49.2 cm3‚min-1. Thus, we carried out the experiments in the flow rate interval of (16.8 to 31.2) cm3‚min-1, which ensured

Journal of Chemical and Engineering Data, Vol. 50, No. 1, 2005 145 Table 5. VLE in the System (1,4-Butanediol + [EMIM][NTf2]) T/K

x1

pexptl /Pa 1

pNRTL /Pa 1

γNRTL 1

ln γNRTL 1

T/K

x1

pexptl /Pa 1

pNRTL /Pa 1

γNRTL 1

ln γNRTL 1

339.6

0.000 0.059 0.152 0.184 0.333 0.362 0.398 0.000 0.053 0.136 0.172 0.307 0.346 0.387 0.000 0.043 0.110 0.156 0.202 0.271 0.330 0.000 0.087 0.143 0.181 0.238 0.299 0.313 0.529 0.556 0.000 0.067 0.095 0.132 0.137 0.209 0.267 0.510 0.540

0.00 11.91 18.18 21.86 24.29 26.00 24.90 0.00 15.95 24.36 30.36 35.16 35.19 31.82 0.00 23.86 35.79 45.27 48.51 52.70 50.13 0.00 51.12 64.18 67.54 77.65 92.41 75.45 105.12 98.98 0.00 73.89 97.54 91.60 103.23 105.66 128.40 147.77 138.95

0.00 11.72 19.44 20.86 24.60 25.10 25.69 0.00 15.75 26.28 28.59 33.36 34.25 35.11 0.00 23.10 39.09 44.24 47.41 50.44 52.31 0.00 49.58 64.32 71.04 78.42 84.36 85.49 99.25 100.46 0.00 75.28 88.85 100.43 101.70 114.09 120.60 139.98 141.83

7.296 5.066 3.280 2.902 1.889 1.775 1.651 7.971 5.594 3.649 3.147 2.050 1.867 1.712 9.441 6.772 4.504 3.608 2.991 2.371 2.016 8.719 5.349 4.204 3.662 3.073 2.630 2.551 1.750 1.688 12.668 7.279 6.086 4.970 4.842 3.560 2.941 1.786 1.710

1.987 1.623 1.188 1.065 0.636 0.574 0.501 2.076 1.722 1.294 1.146 0.718 0.624 0.538 2.245 1.913 1.505 1.283 1.096 0.863 0.701 2.165 1.677 1.436 1.298 1.123 0.967 0.937 0.560 0.523 2.539 1.985 1.806 1.603 1.577 1.270 1.079 0.580 0.537

339.6

0.790 0.855 0.923 0.965 0.969 0.980 1.000 0.788 0.853 0.922 0.964 0.968 0.980 1.000 0.785 0.849 0.920 0.963 0.967 0.980 1.000 0.720 0.782 0.846 0.918 0.962 0.967 0.979 1.000

34.65 34.91 36.29 36.59 38.92 36.30 35.38 48.29 45.19 49.38 51.14 52.59 49.01 47.75 68.72 68.95 72.24 76.24 77.60 74.11 69.45 114.45 94.66 100.10 104.99 108.81 111.22 105.20 99.95

32.72 34.36 36.35 37.75 37.90 38.30 39.06 44.42 46.56 49.26 51.16 51.35 51.92 52.97 66.24 69.18 73.04 75.84 76.13 77.02 78.56 105.28 105.65 105.22 104.41 104.76 104.90 105.46 107.10

1.060 1.029 1.008 1.002 1.001 1.001 1.000 1.064 1.031 1.009 1.002 1.002 1.001 1.000 1.074 1.037 1.011 1.002 1.002 1.001 1.000 1.365 1.262 1.162 1.062 1.017 1.013 1.006 1.000

0.058 0.028 0.008 0.002 0.001 0.001 0.000 0.062 0.031 0.009 0.002 0.002 0.001 0.000 0.071 0.036 0.011 0.002 0.002 0.001 0.000 0.311 0.233 0.150 0.060 0.017 0.013 0.006 0.000

0.709 0.778 0.841 0.916 0.961 0.966 0.979 1.000

158.13 141.19 144.85 147.66 155.86 149.53 149.18 142.39

148.97 149.76 149.49 148.92 149.90 150.16 151.10 153.57

1.367 1.253 1.158 1.059 1.016 1.012 1.005 1.000

0.313 0.225 0.147 0.058 0.016 0.012 0.005 0.000

343.6

348.6

353.6

358.6

that the transporting gas was in saturated equilibrium with the coexisting liquid phase in the saturation tube. The amount of condensed substance was determined by GC analysis using an external standard (hydrocarbon n-CnH2n+2). The saturation vapor pressure psat i at each temperature Ti was calculated from the amount of product collected within a definite period of time. Assuming that Dalton’s law of partial pressures applied to the nitrogen stream saturated were with substance i of interest is valid, values of psat i calculated with

psat i )

miRTa MiV

V ) V N2 + V i

(VN2 . Vi) (1)

where R ) 8.31451 J‚K-1‚mol-1, mi is the mass of transported compound, Mi is the molar mass of the compound, and Vi is its volume contribution to the gaseous phase. VN2 is the volume of transporting gas, and Ta is the temperature of the soap bubble meter. The volume of transporting gas VN2 was determined from the flow rate and time measurements. Data for psat have been obtained as a function of i temperature and were fitted using the following equation:9

R ln psat i ) a +

b T + ∆gl Cp ln T T0

(2)

where a and b are adjustable parameters and ∆gl Cp is the difference in the molar heat capacities of the gas and the liquid phases, respectively. T0 appearing in eq 2 is an arbitrarily chosen reference temperature (which has been chosen to be 298.15 K). Consequently, from eq 2 the expression for the vaporization enthalpy at temperature T is derived:

∆gl Hm(T) ) -b + ∆gl CpT

(3)

343.6

348.6

353.6

358.6

Values of ∆gl Cp have been derived from the isobaric molar heat capacities of the liquid, Clp, of ketones and from values of the isobaric molar heat capacities, Cgp, of the gaseous species calculated according to a procedure developed by Chickos.10 All results together with parameters a and b are listed in Table 1. VLE Measurements of the Binary Mixtures (Solute + IL). Activity coefficients covering the whole range of concentration in a mixture of an ionic liquid and an organic solute can be measured using a dynamic method. This method is based on the so-called transpiration technique described above, which is particularly suitable in such cases where the vapor pressure of the solute is low. About (0.3 to 0.5) g of the IL was weighted in a glass flask together with a certain amount of a solute in order to obtain a desired mole fraction of the liquid phase. About 7 g of glass beads (having a size of 1 mm) were added to the content of the glass flask. Glass beads coated with the initial mixture were placed in the transpiration tube quantitatively. A slow stream of N2 gas flowing through the tube continuously elutes the vapor phase in the glass tubing. Because of the negligible vapor pressure of the ionic liquid, the vapor phase consists exclusively of the solute and is condensed in a cooling trap. The mass of solute collected within a certain time interval is determined by dissolving it in a suitable solvent with a certain amount of internal standard (hydrocarbon). This solution is analyzed using a gas chromatograph equipped with an autosampler. The uncertainty of the amount of solute determined by GC analysis was assessed to be within (1-3)%. The peak area of the solute related to the peak of the external standard (hydrocarbon n-CnH2n+2) is a direct measure of the mass of the

146

Journal of Chemical and Engineering Data, Vol. 50, No. 1, 2005

Table 6. Comparison of Data for the Enthalpy of Vaporization ∆lgHm at 298.15 K technique

∆gl Hm/kJ‚mol-1

T/K

ref

technique

365-430 298.15 278.3-312.3

45.8 46.84 ( 0.22 46.59 ( 0.22

Reich, 1993 Fenwick, 1975 this work

404.1-507.4 282.2-323.0

62.46 ( 0.30 65.46 ( 0.38

Ambrose, 1990 this work

374.0-495.4 298.15 308.2-336.2

63.70 ( 0.05 65.6 ( 0.3 65.40 ( 0.32

Ambrose, 1981 Knauth, 1989 this work

298.15 329.2-363.2

78.3 ( 0.3 78.95 ( 0.92

Eusebio, 2003 this work

346.5-426.9

ebulliometer static manometer

383.1-437.3 363-383

47.86 ( 0.18 39.4 48.38 ( 0.08 38.15 ( 0.40

ebulliometer ebulliometer ebulliometer

312.0-424.8 395.7-478.6

60.29 ( 0.42 63.0 ( 2.2 62.08 ( 0.27

(Hydroxymethyl)-benzene Mathews, 1926 ebulliometer Gardner, 1937 transpiration Dreisbach, 1949

ebulliometer ebulliometer static manometer

323.2-473.2 363-403 333-443

64.8 ( 0.3 68.2 63.6

1,2-Ethanediol Jones, 1952 ebulliometer Schierholz, 1935 calorimeter Gardner, 1972 transpiration

static manometer ebulliometer calorimeter

419-490 416.3-501.5 298.15

77.2 76.13 ( 0.54 79.3 ( 0.5

1,4-Butanediol Gardner, 1972 calorimeter Palczewska,1984 transpiration Knauth, 1989

Results and Discussion

Table 7. Parameters of the NRTL Equation

298.65 303.55 308.55

g12 - g22/ g21 - g11/ kJ mol-1 kJ mol-1

R

T/K

g12 - g22/ g21 - g11/ kJ mol-1 kJ mol-1

Methoxy-benzene + [EMIM][NTf2] 4.31925 -0.6567 0.5 313.55 7.76919 7.34170 -0.2144 0.5 318.55 9.09675 7.19381 0.1814 0.5 323.55 5.95974

0.8612 1.6507 2.1646

R 0.5 0.5 0.5

(Hydroxymethyl)-benzene + [EMIM][NTf2] 298.65 -1.74147 4.11416 0.5 313.55 -1.93743 5.08351 0.5 303.65 -2.01489 5.19008 0.5 318.65 -1.67074 4.60096 0.5 308.65 -2.10974 4.92718 0.5 323.65 -1.02769 3.64881 0.5 1,2-Ethanediol + [EMIM][NTf2] 339.65 10.9296 -2.26446 0.2 353.65 11.5160 343.65 9.64323 -1.91042 0.2 358.65 12.8783 348.65 11.5479 -2.16919 0.2 363.65 13.8182 339.55 343.45 348.45

2.10100 2.25930 2.64094

1,4-Butanediol + [EMIM][NTf2] 4.16248 0.5 353.45 9.10323 4.40652 0.5 358.45 8.74119 4.83005 0.5

ref

Methoxy-benzene Dreisbach, 1949 ebulliometer Glaser, 1957 calorimeter Collerson, 1965 transpiration Lebedeva, 1972

ebulliometer

T/K

∆gl Hm/kJ‚mol-1

T/K

-1.73750 0.2 -1.48613 0.2 -1.50935 0.2 4.42941 0.5 5.55040 0.5

solute condensed into the cooling trap provided a calibration run has been made. From this information, the partial pressure of the solute in the glass tubing can be determined (i.e., the ideal gas law can be applied provided that the vapor pressure of the substance is low enough). Real gas corrections arising from interactions of the vapor with the carrier gas turned out to be negligible. Because the method is a dynamic one, extreme care has to be taken to ensure that thermodynamic equilibrium conditions have been fulfilled by adjusting the gas flow to small enough values. If the amount of condensed solute is small compared to its content in the liquid phase inside the tubing, then the change of concentration in the liquid mixture is negligible during such an experiment, and the partial pressure of the solute can be assigned to the known composition of the liquid mixture that is in thermodynamic equilibrium with the vapor phase. This method was carefully checked6 by measuring the vapor-liquid equilibrium of the binary mixture (n-pentanol + decane), where reliable VLE data exist in the literature.11 Measurements of activity coefficients covering the whole range of concentration of solute (1) + ionic liquid (2) mixtures have been performed. A series of measurements that include methoxy-benzene, (hydroxymethyl)benzene, 1,2-ethanediol, and 1,4-butanediol mixed with an ionic liquid have been studied. Partial pressures of solutes are presented in Tables 2 to 5; the partial pressure of the ionic liquid was not detectable. We checked every system under study for the repeatability of the data and it was governed within (1-3)% by the accuracy of the GC analysis.

Vapor Pressure and Enthalpies of Vaporization of Pure Substances. Most of the vapor pressure values for anisol, benzyl alcohol, and diols that are reported in the literature were measured using a dynamic recirculation still. That is why they are referenced to elevated temperatures above 363 K. In general, the transpiration method used in this work provides reliable experimental vapor pressures in the temperature range around ambient temperature. Therefore, a direct comparison of our vapor pressures with those available from the literature is not possible. However, one way to relate the literature data to our measurements is to compare the enthalpies of vaporization at the reference temperature, 298.15 K. For this purpose, we treated the p-T results available in the literature using eqs 2 and 3 and calculated ∆gl Hm (298.15 K) for the sake of comparison with our results (Table 6). As can be seen from Table 6, enthalpies of vaporization derived from both methods (static and transpiration) are in very close agreement within the boundaries of their experimental uncertainties. Data Correlation of Binary Systems Using the NRTL Equation. The values of γ1 of different solutes in [EMIM][NTf2] obtained at four different temperatures are listed in Tables 2 to 5.

p1 ) p0,1x1γNRTL 1 with

[(

ln γNRTL ) x22 τ21 1

)

G21 x1 + x2G21

2

+

(4)

τ12G12

]

(x2 + x1G12)2

(5)

where Gij ) exp(-Rijτij) with τij ) (gij - gjj)/RT and Rij ) Rji ) R (i, j ) 1, 2; i * j). Table 7 contains the parameters Rij and (gij - gjj). Figures 1 to 4 show the experimental results for the partial pressures of the solutes and activity coefficients γ1 of the solutes mixed with [EMIM][NTf2] in comparison with the calculated results of the NRTL model according to eq 5 with parameters taken from Table 6. The scattering of the experimental data is about 5% of the maximal pressure of the pure solutes, which is not surprising considering the low values of absolute pressures obtained in the experiments. The NRTL equation is able to fit all of the results within the experimental errors. The temperature dependence of ln γi indicates that ln γ1 increases with increasing temperature. However, because of the relatively large scattering of the data this temper-

Journal of Chemical and Engineering Data, Vol. 50, No. 1, 2005 147

Figure 1. Partial pressure data of methoxy-benzene in the mixture with [EMIM][NTf2] as a function of x1 (methoxy-benzene).

Figure 4. Partial pressure data of 1,4-butanediol in the mixture with [EMIM][NTf2] as a function of x1 (1,4-butanediol).

Clp Cgp ∆gl Cp γi τij Rij

molar heat capacities of liquid at constant pressure molar heat capacities of gas at constant pressure difference of the molar heat capacities at constant pressure for the gaseous and liquid phases, respectively activity coefficient of component i interaction parameters of the NRTL equation interaction parameters of the NRTL equation

Literature Cited

Figure 2. Partial pressure data of (hydroxymethyl)-benzene in the mixture with [EMIM][NTf2] as a function of x1 ((hydroxymethyl)-benzene).

Figure 3. Partial pressure data of 1,2-ethanediol in the mixture with [EMIM][NTf2] as a function of x1 (1,2-ethanediol).

ature dependence of ln γ1 is not significant enough to derive enthalpies of mixing. List of Symbols ∆gl Hm Ta p

molar enthalpy of vaporization ambient temperature vapor pressure

(1) Heintz, A.; Kulikov, D. V.; Verevkin, S. P. Thermodynamic Properties of Mixtures Containing Ionic Liquids. 1. Activity Coefficients at Infinite Dilution of Alkanes, Alkenes, and Alkylbenzenes in 4-Methyl-n-butylpyridinium Tetrafluoroborate Using Gas-Liquid Chromatography. J. Chem. Eng. Data 2001, 46, 1526-1529. (2) Heintz, A.; Kulikov, D. V.; Verevkin, S. P. Thermodynamic Properties of Mixtures Containing Ionic Liquids. Activity Coefficients at Infinite Dilution of Polar Solvents in 4-Methyl-N-ButylPyridinium Tetrafluoroborate Using Gas-Liquid Chromatography. J. Chem. Thermodyn. 2002, 34, 1341-1347. (3) Heintz, A.; Kulikov, D. V.; Verevkin, S. P. Thermodynamic Properties of Mixtures Containing Ionic Liquids. 2. Activity Coefficients at Infinite Dilution of Hydrocarbons and Polar Solutes in 1-Methyl-3-ethyl-imidazolium Bis(trifluoromethyl-sulfonyl) Amide and in 1,2-Dimethyl-3-ethyl-imidazolium Bis-(trifluoromethyl-sulfonyl) Amide Using Gas-Liquid Chromatography. J. Chem. Eng. Data 2002, 47, 894-899. (4) Heintz, A.; Lehmann, J. K.; Verevkin, S. P. Thermodynamic Properties of Liquid Mixtures Containing Ionic Liquids. Ionic Liquids as Green Solvents: Progress & Prospects; ACS Symposium Series 856, American Chemical Society: Washington, DC, 2003; pp 134-151. (5) Marczak, W.; Verevkin, S. P.; Heintz, A. Enthalpies of Solution of Organic Solutes in the Ionic Liquid 1-Methyl-3-ethyl-imidazolium Bis-(trifluoromethyl-sulfonyl) Amide. J. Solution Chem. 2003, 32, 519-526. (6) Verevkin S. P.; Vasiltsova, T. V.; Bich, E.; Heintz, A. Thermodynamic Properties of Mixtures Containing Ionic Liquids. Activity Coefficients of Aldehydes and Ketones in 1-Methyl-3-EthylImidazolium Bis(trifluoromethyl-sulfonyl) Imide Using the Transpiration Method. Fluid Phase Equilib. 2004, 218, 165-175. (7) Solvent Innovation. http://www.solvent-innovation.de (8) Wertz, Ch. Diploma Thesis, University of Rostock, 2002. (9) Kulikov, D. V.; Verevkin S. P.; Heintz, A. Enthalpies of vaporization of a series of linear aliphatic alcohols. Experimental measurements and application of the ERAS-model for their prediction. Fluid Phase Equilib. 2001, 192, 187-202. (10) Chickos, J. S.; Hesse, D. G.; Liebman, J. F. J. A Group Additivity Approach for the Estimation of Heat Capacities of Organic Liquids and Solids. Struct. Chem. 1993, 4, 261-269. (11) Treszczanowicz, T.; Treszczanowicz. A. J. Vapor-liquid equilibriums of nonelectrolyte mixtures. Part III. Vapor-liquid-phase equilibriums of binary systems formed by 1-pentanol and alkanes. Bull. Acad. Pol. Sci. 1979, 27, 689-695.

148

Journal of Chemical and Engineering Data, Vol. 50, No. 1, 2005

(12) Mathews, J. H. The Accurate Measurement of Heats of Vaporization of Liquids. J. Am. Chem. Soc. 1926, 48, 562-576. (13) Dreisbach, R. R.; Shrader, S. A. Vapor Pressure-Temperature Data on Some Organic Compounds. Ind. Eng. Chem. 1949, 41, 2879-2880. (14) Glaser, F.; Ruland, H. Untersuchungsen der Dampfdruckkurven und Dritische Daten einiger technisch wichtiger organischer Substanzen. Chem. -Ing. -Techn. 1957, 29, 772. (15) Lebedeva, N. D.; Katin, Yu. A. Heats of combustion of certain monosubstituted benzenes. Russ. J. Phys. Chem. (Engl. Transl.) 1972, 46, 1088. (16) Reich, R.; Sanhueza, V. Vapor-Liquid Equilibria for R-Pinene or β-Pinene with Anisol. J. Chem. Eng. Data 1993, 38, 341-343. (17) Fenwick, J. O.; Harrop, D.; Head, A. J. Thermodynamic properties of organic oxygen compounds. 41. Enthalpies of formation of eight ethers. J. Chem. Thermodyn. 1975, 7, 944-954. (18) Gardner, G. S.; Brewer, J. E. Vapor Pressure of Commercial HighBoiling Organic Solvents. Ind. Eng. Chem. 1937, 29, 2, 179-181. (19) Jones, W. S.; Tamplin, W. S. Glycols; American Chemical Society’s Series of Chemical Monographs, 1952 (cited in Boublik, T.; Fried V.; Hala, E. The Vapour Pressure of Pure Substances; Physical Science Data 17, Elsevier: Amsterdam, 1984.) (20) Ambrose, D.; Ghiassee, N. B. Vapor pressures, critical temperatures, and critical pressures of benzyl alcohol, octan-2-ol, and 2-ethylhexan-1-ol. J. Chem. Thermodyn. 1990, 22, 307-11. (21) Hales, J. L.; Cogman, R. C.; Frith, W. J. A Transpiration-GLC. Apparatus for Measurement of Low Vapor Concentration. J.

Chem. Thermodyn. 1981, 13, 591-601. (22) Gardner, P. J.; Hussain, K. S. The standard enthalpies of formation of some aliphatic diols. J. Chem. Thermodyn. 1972, 4, 819-827. (23) Schierholtz O. J.; Staples, M. L. Vapor Pressure of Certain Glycols. J. Am. Chem. Soc. 1935, 57, 2709-2711. (24) Ambrose, D.; Hall, D. J. Thermodynamic Properties of Organic Oxygen Compounds L. The Vapor Pressures of 1,2-Ethanediol(Ethylene Glycol) and Bis(2-hydroxyethyl) Ether (Diethylene Glycol). J. Chem. Thermodyn. 1981, 13, 61-66. (25) Eusebio, M. E.; Jesus, A. J. L.; Cruz, M. S. C.; Leitao, M. L. P.; Redinha, J. S. Enthalpy of vaporisation of butanediol isomers. J. Chem. Thermodyn. 2003, 35, 123-129. (26) Palczewska-Tulinska, M.; Cholinski, J.; Szafranski, A. M.; Wyrzykowska-Stankiewicz, D. Experimental vapor pressures and maximum-likehood antoine-equation constants for 1,1,1-methoxydimethylpropane, thiacyclopentane and 1,4-butanediol. Fluid Phase Equilib. 1984, 15, 295-307.

Received for review June 15, 2004. Accepted November 4, 2004. T.V.V. gratefully acknowledges a research scholarship from the DAAD (Deutscher Akademischer Austauschdienst).

JE0497799