Subscriber access provided by UNIV OF DURHAM
Article
Dynamic Stocks and Flows Analysis of Bisphenol A (BPA) in China: 2000-2014 Daqian Jiang, Wei-Qiang Chen, Xianlai Zeng, and Linbin Tang Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.7b05709 • Publication Date (Web): 13 Feb 2018 Downloaded from http://pubs.acs.org on February 13, 2018
Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.
Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.
Page 1 of 30
Environmental Science & Technology
1
Dynamic Stocks and Flows Analysis of Bisphenol A (BPA) in China: 2000-2014
2
Daqian Jiang,1* Wei-Qiang Chen,2,3,4* Xianlai Zeng,5 Linbin Tang2,3,4
3 4 5
1. Environmental Engineering Department, Montana Tech, Butte, Montana 59701, United States
6
2. Key Lab of Urban Environment and Health, Institute of Urban Environment, Chinese
7
Academy of Sciences, Xiamen, Fujian 361021, China
8
3. Xiamen Key Lab of Urban Metabolism, Xiamen, 361021, China
9
4. University of Chinese Academy of Science, Beijing, 100049, China
10
5. School of Environment, Tsinghua University, Beijing 100084, China
11 12 13
Correspondence to:
[email protected];
[email protected] 14
1 ACS Paragon Plus Environment
Environmental Science & Technology
15
TOC Art
16
2 ACS Paragon Plus Environment
Page 2 of 30
Page 3 of 30
Environmental Science & Technology
17
Abstract
18
Bisphenol A (BPA), a synthetic organic chemical, is creating a new category of ecological and
19
human health challenges due to unintended leakage. Effectively managing the use and leakage of
20
BPA can benefit from an understanding of the anthropogenic BPA cycles (i.e., the size of BPA
21
flows and stocks). In this work, we provide a dynamic analysis of the anthropogenic BPA cycles
22
in China for 2000-2014. We find that China’s BPA consumption has increased 10-fold since
23
2000, to ~3 million tonnes/year. With the increasing consumption, China’s in-use BPA stock has
24
increased 500-fold to 14.0 million tonnes (i.e., 10.2 kg BPA/capita). It is unclear whether a
25
saturation point has been reached, but in 2004-2014, China’s in-use BPA stock has been
26
increasing by 0.8 kg BPA/capita annually. Electronic products are the biggest contributor,
27
responsible for roughly one third of China’s in-use BPA stock. Optical media (DVD/VCD/CDs)
28
is the largest contributor to China’s current End-of-Life (EoL) BPA flow, totaling 0.9 million
29
tonnes/year. However, the EoL BPA flow due to e-waste will increase quickly, and will soon
30
become the largest EoL BPA flow. The changing quantities and sources of EoL BPA flows may
31
require a shift in the macroscopic BPA management strategies.
3 ACS Paragon Plus Environment
Environmental Science & Technology
32
Introduction
33
Bisphenol A (BPA), like many other synthetic organic chemicals, is becoming an important part
34
of the material basis of the modern society. Currently, the global BPA consumption has
35
surpassed seven million tonnes per year,1 and is expected to continue to increase2, 3 due to the
36
wide use of BPA in electronics, automobiles, water bottles, and food packaging.4, 5
37
Unlike other bulk materials (e.g., minerals), synthetic organic chemicals present unique
38
environmental toxicity and persistence challenges. For example, in the case of BPA, it was found
39
that BPA monomers could leach out from BPA-containing products,6, 7 and when it does, it is an
40
endocrine disruptor to humans and animals.8-10 Due to the wide use and thereby widely
41
distributed sources,11, 12 BPA leakage is widespread. BPA has been detected in food or food
42
containers globally,13-16 atmospheric aerosols globally,17 surface water in North America and
43
Europe,18 virtually all urine samples in the US population,19 and population in southern China
44
with dermal exposure to BPA-containing paper.20 Sometimes BPA is detected in high
45
concentrations, e.g., exceedance of Canadian predicted no-effect levels for aquatic life was
46
reported in Asia, America, and Europe.11
47
To properly manage BPA as a material and the associated toxicity risks, it is helpful to develop a
48
macroscopic understanding of the BPA flows and “stock” in society. Stock, or in-use material
49
stock, is a concept in industrial ecology, defined as the amount of a material that is in active use
50
in society. As products are produced, used, and disposed of (i.e., flows), the amount of in-use
51
material stock changes (the exercise of depicting the flows and stock of a material is often
52
termed as characterizing anthropogenic cycles). Understanding the changes in flows and stocks
53
can provide insights into material sustainability and criticality.21, 22 In some cases (e.g., toxic
4 ACS Paragon Plus Environment
Page 4 of 30
Page 5 of 30
Environmental Science & Technology
54
metals), it can also furnish useful insights into managing the risks associated with the unintended
55
leakage (flows).23-25
56
So far, efforts on systemically characterizing the anthropogenic cycle of synthetic organic
57
chemicals are only beginning to emerge.26, 27 Specific to BPA, Pivnenko et al. 2016 delineated
58
the BPA cycles in the paper industry, which exemplified how stocks and flows analysis could
59
provide useful industry-level insights on the most effective strategies for reducing chemical
60
contamination.28 However, at the country level, stocks and flows analysis for BPA remains
61
unavailable, with current knowledge limited to BPA flows, such as the tonnage of BPA used in
62
producing polycarbonate plastics or epoxy resins annually (which are the primary use of BPA),
63
and the tonnage of epoxy resins by different products annually.1
64
Herein, we characterize the anthropogenic BPA cycles in China. Understanding the
65
anthropogenic BPA cycles can identify hotspots of BPA flows on the national and regional
66
scales, and provide a basis for understanding how BPA flows might evolve in the future.
67
Understanding the anthropogenic BPA cycles in China also has particular implications in global
68
BPA management, as China currently accounts for a quarter of the global BPA consumption, and
69
is projected to be the largest BPA consumer, and possibly the largest BPA producer, around
70
2020. 29, 30
71 72
Materials and Method
73
System Definition
5 ACS Paragon Plus Environment
Environmental Science & Technology
74 75
Figure 1. Framework for the anthropogenic BPA cycle (modified from Chen and Graedel 201221)
76
A conceptual framework for the anthropogenic BPA cycle is depicted in Fig 1, which comprises
77
five life stages: BPA production, polycarbonate plastics/epoxy resin production, production of
78
final products, the use stage, and the EoL management. Each arrow in the diagram represents a
79
flow, and each white box represents a stock.
80
•
which are produced directly or indirectly from fossil fuels (particularly petroleum). 31
81 82
BPA production: BPA (Fig S1) is produced via the condensation of acetone and phenol,
•
Polycarbonate plastics/epoxy resin production: BPA monomers are often not directly
83
used. Globally and in China, over 90% of the BPA monomers are used to synthesize
84
polycarbonate plastics (PC) and epoxy resins 1 through the polymerization process (Fig
85
S2). Only the BPA contained in PC/epoxy resin flows and stocks are included in this
86
study, which is approximately 95% of China’s total BPA consumption. Non-polymerized
87
BPA use, such as in thermal paper, is not included.
6 ACS Paragon Plus Environment
Page 6 of 30
Page 7 of 30
88
Environmental Science & Technology
•
Final products: PC and epoxy resins are used in a wide array of products, such as
89
automobiles, electronics, and water bottles, among others. Waste flows (e.g., scrap PC)
90
are generated in this stage and transferred directly to the EoL management stage.
91
•
Use: The final products that contain BPA are widely used. A portion of the BPA in final
92
products will accrue as the in-use stock, and the remaining will be transferred to the EoL
93
management. We distinguish between dissipative loss (leakage) and leaching, with
94
dissipative loss defined as the material loss in the production process, and leaching
95
defined as the unintended release of BPA monomers in the use or EoL phase due to
96
chemical reactions (e.g., BPA leaching from PC plastic water bottles7, 16). Only
97
dissipative losses are included in this study.
98 99
•
EoL management: The EoL management includes the landfilling, incineration, and recycling of wastes that contain BPA. Landfilling leads to the accumulation of BPA in
100
landfills, and likely, BPA leaching.32 Incineration can destroy BPA completely.33, 34
101
Recycling of BPA is also technologically feasible.35, 36
102 103
Data Compilation, Modeling and Analysis
104
This section explains the data compilation and modeling methods used in this study. Years 2000-
105
2014 are used as the time boundary throughout the analysis. To understand the potential bias
106
caused by the truncated time boundary, an initial stock is introduced as part of the uncertainty
107
analysis, in which case years 1992-2014 are included.
108
BPA production: The BPA flows in the BPA production stage are obtained by harmonizing
109
China’s BPA production data from different sources,37, 38 and the customs data,39 which details
7 ACS Paragon Plus Environment
Environmental Science & Technology
110
the import and export of BPA in its primary form. The data used are provided in the SI (Table
111
S1).
112
PC/epoxy resin production: The flows of PC and epoxy resins are obtained by harmonizing the
113
customs data,39 and China’s production and consumption data.40-46 The data used are provided in
114
the SI (Table S1). The BPA content in PC or epoxy resins is estimated by applying a BPA
115
content factor, i.e. kg BPA/kg PC and kg BPA/kg epoxy resin. The BPA content factors are
116
primarily based on an industry report,47 which suggests that 0.89 kg BPA/kg PC and 0.7 kg
117
BPA/kg epoxy resin are reasonable for PC and epoxy resins, respectively.
118
BPA flows to final products: The key final products that require PC or epoxy resin flows are
119
identified based on industry report1 and academic publications (Table S2). Optical media
120
(CD/VCD/DVDs), construction materials (PC sheets/boards), automobile manufacturing,
121
electronic devices/parts, packaging (PC water bottles), and others (medical devices) are the key
122
final products that use PC. Paint, electronic parts/devices, construction, and composite materials
123
are the key final products that use epoxy resins.
124
Statistics on the PC and epoxy resin flows to final products are only available for some years
125
(detailed in Table S2). Briefly, PC consumption by final product categories is available for years
126
2005, 2007, 2012, and 2014. Epoxy resin consumption by final product categories is available
127
for years 2004, 2010, and 2012.
128
For years without reported statistics, the PC and epoxy resin flows to final products are estimated
129
by multiplying an intensity factor, defined as the PC or epoxy resin content per physical unit of
130
the final product (e.g., kg PC per unit of cars), with the production volume of the final product.
131
For example, using available statistics, the PC intensity is estimated as 8.0 and 8.6 kg BPA per
8 ACS Paragon Plus Environment
Page 8 of 30
Page 9 of 30
Environmental Science & Technology
132
car in 2007 and 2012 respectively. Then the PC intensity for cars in 2008-2011 is estimated as
133
(8.0+8.6)/2 = 8.3 kg BPA per car, which is then multiplied by the production volume of
134
automobiles in 2008-2011 to obtain the PC flows to auto manufacturing in those years. The
135
estimated PC/epoxy resin flows are finally converted to BPA flows using the BPA content
136
factors (0.89 and 0.70 kg BPA/kg PC and epoxy resin respectively).
137
The parameters used to estimate the PC/epoxy resin intensity factor for each final product are
138
detailed in Table 1 in the “Production Volume” column. For example, the PC used in packaging
139
is estimated using the PC content per tonne of bottled drinking water produced, while the epoxy
140
resins used in electronic products is estimated using the epoxy resin content per tonne of
141
electronic products produced (Table 1). The intensity factors for final products with reported
142
statistics are provided in Table S1. Imported products are assumed to have identical PC/epoxy
143
resin intensity as domestically produced products. The production, import and export data for the
144
final products are obtained from China’s Statistical Yearbook,39 and trade data.39, 48
145
9 ACS Paragon Plus Environment
Environmental Science & Technology
146
Page 10 of 30
Table 1. The parameters used to estimate the PC/epoxy resin flows to different final products Type of Parameter
Sector GDP (RMB)
Production Volume (physical units)
PC
Optical media
units of CD/VCD/DVDs
printing and recording media production
Construction materials (PC boards)
tonnage of PC boards
construction
Automobiles
units of passenger cars
auto manufacturing
tonnage of bottled drinking water total weight of electric appliances/devices
wholesale and retail of beverages manf. electrical machinery/equipment; manf. wholesale and retail of electric electronic/communication equipment household appliances wholesale of construction total area under construction materials
Packaging Electronic devices/parts
Epoxy Resins
Wholesale and/or Retail (RMB) retail of audio/video/epublications wholesale of construction materials wholesale and retail of autos
food, beverage, tabacco production
Paint
tonnage of paint
Electronic devices/parts
total weight of electric appliances/devices
manf. electrical machinery/equipment; manf. wholesale and retail of electric electronic/communication equipment household appliances
Construction
finished area under construction
construction
wholesale of construction materials
Auto & composite materials
units of passenger cars
auto manufacturing
wholesale and retail of autos manf. stands for "manufacturing of"
147 148
In-use BPA stock: The in-use BPA stock is the accumulation of BPA in the final products that
149
are in active use. For each final product, the BPA accumulated in in-use stock is calculated as
150
follows:
151
= + ∆
(Equation 1)
152
, ∆ = ∑( , − )
(Equation 2)
153
, =
154
, =
155
where is the in-use stock at the end of year t+1; is the in-use stock at the end of year t;
156
∆ is the change of in-use stock in year t+1; , is the input to the BPA stock through
157
product i in year t+1, which is the sum of domestic production ( , ) and import
158
!"#$, ( +1 ); , is the output from BPA stock through product i in year t+1, which is the
,
,
,
+
(Equation 3)
+ ,
(Equation 4)
10 ACS Paragon Plus Environment
Page 11 of 30
Environmental Science & Technology
159
%#&, , sum of export ( , ) and EoL flow ( +1 ). , , and ,
160
are estimated using the method explained in the previous section. The estimation of , is
161
described in the next section.
162
EoL BPA flows: EoL BPA flows are estimated using lifetime models. For optical media,
163
construction media, automobiles, packaging, and paint, the generation of EoL BPA flows
164
( , ) is estimated based on the normal lifetime model (assuming that the lifespan of a
165
product in in-use stock follows the normal distribution):
166
, = ∑(+,--- ' (, − (
167
(, = .
168
where , is the EoL BPA flow (contained in product i) in year t+1; (, is the
169
probability for product i that was produced in year j to reach EoL in year t+1;