Effect of Silica and Alumina on Petroleum Coke Ash Fusibility

Nov 27, 2017 - The effects of SiO2/Al2O3 (S/A) and (SiO2 + Al2O3) ratios on the synthetic petroleum coke (petcoke) ash fusibility are investigated in ...
3 downloads 0 Views 6MB Size
Subscriber access provided by READING UNIV

Article

Effect of Silica and Alumina on Petroleum Coke Ash Fusibility Jiazhou Li, Xiaoyu Wang, Bing Wang, Jiantao Zhao, and Yitian Fang Energy Fuels, Just Accepted Manuscript • DOI: 10.1021/acs.energyfuels.7b02843 • Publication Date (Web): 27 Nov 2017 Downloaded from http://pubs.acs.org on November 27, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Energy & Fuels is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

1

Effect of Silica and Alumina on Petroleum Coke Ash Fusibility

2

Jiazhou Li,a, b Xiaoyu Wang, c Bing Wang,a, b Jiantao Zhao,*, a Yitian Fanga

3

a

State Key Laboratory of Coal Conversion, Institute of Coal Chemistry, Chinese Academy of Sciences, Taiyuan, Shanxi 030001, China

4 5

b

University of Chinese Academy of Sciences, Beijing 100049, China

6

c

College of Optoelectric Science and Engineering, National University of Defense

7

Technology, Changsha, Hunan 410073, China

8

ABSTRACT: Silica (Si) and alumina (Al) elements are always considered to be the

9

important inducements for ash sintering and slagging in the boilers. The effects of

10

SiO2/Al2O3 (S/A) and (SiO2+Al2O3) ratios on the synthetic petroleum coke (petcoke)

11

ash fusibility are investigated in this work. Experimental methods including ash

12

fusion temperatures (AFTs) tests, X-ray diffraction (XRD), and scanning electronic

13

microscopy (SEM) are applied to investigate the AFTs, the mineral composition and

14

surface morphologies of high-temperature ashes. Moreover, thermodynamic

15

equilibrium calculations are also used to predict the ash fusion process. The results

16

show that the AFTs of petcoke ash samples are closely related to the addition of S/A

17

and (SiO2+Al2O3). The dominant crystalline phases formed in high-temperature ashes

18

with different S/A and (SiO2+Al2O3) are gehlenite (Ca2Al2SiO7), quartz (SiO2), nickel

19

orthosilicate (Ni2SiO4), and mullite (Al6Si2O13). The AFTs drop sharply with

20

increasing S/A until it reaches 1.5, which may be ascribed to the gradual decline of

21

high-melting Al6Si2O13. Then, the AFTs follow a slight increase within the S/A range

22

of 1.5-3.0. As (SiO2+Al2O3) increases from 20 to 60%, the AFTs show the continuous

23

increase because of the formation of anorthite (CaAl2Si2O8) and Al6Si2O13 and the

24

increased content of SiO2. The high-temperature ashes with the S/A and (SiO2+Al2O3) 1

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

25

of 1.5 and 20% have the higher molten extent. Particles in these ashes are almost in

26

complete agglomeration, and present the denser layer structure and more smooth

27

surface.

28

1. INTRODUCTION

29

The production of petcoke is continuously increasing with the deep processing

30

of heavy crudes in refineries [1-4]. Petcoke is generally considered as an attractive

31

fuel that generates steam or power in boilers since it has some particular advantages,

32

such as high fixed carbon, low ash content, and low price. In boilers, petcoke ash

33

melts in whole or in part at high temperatures because of the eutectic melting of

34

minerals [5-7]. The molten ash deposited on the inner wall of pipes of boilers may

35

cause fireside sintering and fouling [8]. The deposited ash impedes heat transfer to

36

some extent, and even blocks the flue gas channel in boilers [9,10]. Thus, choosing

37

the petcoke with suitable ash fusibility is required to avoid ash sintering and fouling.

38

The ash fusion behaviors are critical for the selection of petcoke and operation of

39

boilers. There have been many experimental techniques focused on the evaluation of

40

ash fusion behaviors [5,8,11-14], such as AFTs tests, high-temperature processing

41

microscope (HTPM), and thermomechanical analysis (TMA). Among these

42

techniques, AFTs tests are widely applied to guide the utilization of petcoke while

43

concerning the ash fusibility. AFTs can provide not only an indication of the ash

44

softening and melting behavior, but also an information of the progressive melting of

45

ash to slag [15]. Four characteristic temperatures, i.e., initial deformational

46

temperature (DT), softening temperature (ST), hemispherical temperature (HT), and

47

flow temperature (FT), are defined by the shape variation of an ash cone at elevated

48

temperatures.

2

ACS Paragon Plus Environment

Page 2 of 34

Page 3 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

49

The ash fusibility at high temperatures is essentially associated with the ash

50

chemical composition, as well as their interactions [16]. Numerous researches have

51

been performed to investigate the relationships between AFTs and ash chemical

52

composition. Liu et al. [17] found that the AFTs decreased with the addition of Fe2O3

53

while changing little as the K2O content increased. For the addition of CaO, the AFTs

54

initially declined and then followed an increase. Wang et al. [18] pointed out that

55

Na2O could decrease the AFTs markedly. van Dyk [19] studied the effects of acidic

56

constituents (Si, Al, and Ti) on the ash fusibility. It was found that all acidic

57

constituents had positive influences on ash flow temperature. The effect of S/A ratio

58

on the AFTs was investigated by Liu et al [17]. The results indicated that AFTs had a

59

decline before S/A reached 1.5, and then remained constant or increased slightly as

60

S/A further increased. The formation of different melting points (MP) minerals during

61

ash melting processes is generally used to interpret the variation of AFTs [20]. AFTs

62

are also correlated with thermodynamic equilibrium calculations. Rizvi et al [21] used

63

simultaneous thermal analysis (STA) to predict the ash fusion behavior. It was found

64

that STA could assess the physicochemical changes occurred in the process of ash

65

fusion, as well as the possible chemical reactions. Jak [22] put forward a new AFTs

66

prediction method using equilibrium phase diagram. It was demonstrated that AFTs

67

could be predicted effectively via the developed F*A*C*T* thermodynamic database.

68

Although there are many researches focused on the effect of ash composition on the

69

coal ash fusibility, little has been reported about the relationships between petcoke ash

70

composition and the ash fusion characteristics.

71

In general, the major ash composition of coal are Si, Al, Ca, Fe, K, and Na,

72

whereas the petcoke ash is mainly composed of V, Ni, Si, Al, Fe, and Ca. Moreover,

73

the mass percentage of V and Ni in petcoke ash is usually higher than 20 and 10%, 3

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 4 of 34

74

respectively [23]. The ash compositional differences between petcoke and coal may

75

cause different mineral transformation behaviors because of the presence of V and Ni

76

in petcoke. We have investigated the effect of petcoke ash composition (V2O5, NiO,

77

CaO, and Fe2O3) on ash fusion behaviors in previous researches [24,25]. The acidic

78

ash constituents SiO2, Al2O3, and TiO2 are generally considered to act as receptors

79

(network formers) and the basic oxides CaO, Fe2O3, Na2O, K2O, and MgO as oxygen

80

donators

81

(CaO+Fe2O3+Na2O+K2O+MgO)/(SiO2+Al2O3+TiO2), which is same as the effect of

82

(SiO2+Al2O3) ratio, has been used to rank the propensity of melting, fouling, and

83

slagging [27-30]. Moreover, the S/A ratio is also an important factor for the initial

84

evaluations of ash fusibility [31,32]. In this work, both S/A and (SiO2+Al2O3) ratios

85

are considered to characterize the influences of SiO2 and Al2O3 on petcoke ash fusion

86

behaviors, which is expected to provide a guide for the efficient utilization of petcoke.

87

To eliminate the impacts of impurities and complex phases in petcoke ash and

88

simplify the ash system, the synthetic ash rather than real ash is selected to study the

89

ash fusion process according to the literatures [17,18,33-36]. Moreover, the chemical

90

composition of synthetic ash system can be controlled accurately. Thus, experimental

91

samples were prepared by V2O5, NiO, SiO2, Al2O3, Fe2O3, and CaO via blending pure

92

oxides. AFTs tests are carried out to identify the four characteristic temperatures of

93

ash samples. XRD and SEM are combined to examine the mineral composition and

94

surface morphologies of high-temperature ash samples. The ash fusion process is also

95

calculated by thermodynamic equilibrium calculations via the multiple components

96

system of V2O5-NiO-SiO2-Al2O3-Fe2O3-CaO.

97

2. EXPERIMENTAL SECTION

98

2.1. Synthetic Ash Samples.

(network

modifiers)

[26].

The

base-acid

4

ACS Paragon Plus Environment

ratio

R

defined

as

Page 5 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

99

The chemical composition of five petcoke ashes (Shanxi local oil refinery,

100

Wuhan Petrochemical Co., Zhenhai Petrochemical Co., Zibo Qilu Petrochemical Co.,

101

Ltd., and Daqing Oilfield) prepared at 973 K for 24 h [37] is shown in Table 1. Based

102

on these ash composition, synthetic ash samples were prepared by V2O5, NiO, SiO2,

103

Al2O3, Fe2O3, and CaO since these six constituents account for more than 93 wt% of

104

petcoke ash. Table 2 lists the chemical composition of synthetic ash samples, and they

105

were divided into two groups. In Group 1, (SiO2+Al2O3) and other basic oxides were

106

constant while S/A varied from 0.5 to 3. In Group 2, S/A kept constant, but the total

107

amounts of (SiO2+Al2O3) changed within the range of 20-60 wt%. The six analytical

108

reagents were blended well by ball milling for 1 h.

109

2.2. Measurements of AFTs.

110

The AFTs of synthetic ash samples were measured by a AFTs tester from KY

111

company, China. The tests were carried out following the Chinese standard procedure

112

GB/T 219-2008 at oxidizing (air) atmosphere [38], which provided a valuable guide

113

for the slagging of combustion. An ash cone with a specific geometry was heated at

114

15 K/min to 1173 K, and then changed at 5 K/min to the flow temperature. In the

115

procedure, the four characteristic temperatures, i.e., DT, ST, HT, and FT, were

116

identified and recorded automatically with the accuracy of 1 K according to the

117

variation of the certain shape of ash cone. Repeated AFTs measurements were

118

performed.

119

2.3. Quenching Experiments.

120

Quenching experiments were performed to obtain the high-temperature ash slag

121

in a tube furnace. The experimental temperature varies from 1273 to 1573 K, with the

122

interval of 100 K. Figure 1 shows the schematic diagram of the tube furnace. The

123

synthetic ash (1.0 g) that filled into a corundum crucible was heated according to the 5

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

124

thermal profile of the AFTs tests. After reaching the set temperature and residence

125

time (15 min) [24,39], the sample was taken out immediately, quenched in ice water,

126

and then collected for testing.

127

2.4. Instrumental Analysis.

128

The chemical composition of five petcoke ashes was identified by X-ray

129

fluorescence (XRF) spectrometry from Shimadzu, Japan with a Rh target X-ray tube

130

(50 kV, 40 mA). Before testing the quenched high-temperature ash slag was ground to

131

below 74 µm. The surface morphologies of the quenched slag samples were observed

132

by a scanning electron microscope (JSM-7001F). Furthermore, an X-ray power

133

diffractometer (RIGAKU D/max-rB) with Cu Ka radiation (40 kW, 100 mA,

134

Ka1=0.15408 mm) was applied to examine the mineral composition of the quenched

135

slag samples. The samples were scanned from 10 to 80° at 4° 2θ/min scanning speed

136

with 0.01° step size.

137

2.5. Thermodynamic Equilibrium Calculations.

138

The thermodynamic software package FactSage was used to establish a multiple

139

components system of V2O5-NiO-SiO2-Al2O3 -Fe2O3-CaO, which was to analyze the

140

potential multiphase equilibria, proportions of liquid and solid phases in specified

141

atmospheres and temperatures. In equilibrium calculations, FToxid and FactPS

142

databases were selected for phase formation data. The solution species that formed

143

possibly were chosen from FToxid database. However, FactSage did not have the

144

database to deal with the interactions between VOx and slag [40-42]. Thermodynamic

145

equilibrium calculations were performed at oxidizing (air) atmosphere under 0.1 MPa.

146

FactSage was based on the Gibbs free energy minimization, indicating that the lower

147

the Gibbs free energy, the higher the priority of the reaction [43]. Note that, phases

148

that formed at concentrations lower than 0.01 wt% were ignored in calculations. 6

ACS Paragon Plus Environment

Page 6 of 34

Page 7 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

149

Although FactSage is a powerful tool to calculate solid phase components and

150

liquid phase change at high temperatures, there do exist some shortcomings when it is

151

applied to ash fusion. It does not take into account the chemical kinetics in

152

calculations. Furthermore, temperature and composition gradients during ash fusion

153

are not also considered. Nonetheless, thermodynamic calculation is still a valuable

154

method that provides insight into the ash fusion [44].

155

3. RESULTS AND DISCUSSION

156

3.1. Effect of S/A on AFTs.

157

The AFTs of synthetic ash samples in Group 1 as a function of S/A is present in

158

Figure 2. AFTs drop sharply with increasing S/A until it reaches 1.5 where FT drops

159

to 1527 K. The reasonable explanation may be as follows: low S/A (lower than 1.0)

160

results in the formation of high-melting point minerals, such as mullite. However,

161

there exist no high-melting minerals when S/A reaches 1.5, which decreases the AFTs

162

markedly. At higher S/A, AFTs increase gradually.

163

3.2. Effect of S/A on Mineral Transformation Behavior at High Temperatures.

164

The minerals interact and melt into liquid during ash fusion, causing the

165

variation in minerals composition and their content. Thus, the crystal phase

166

components in ash at a certain temperature can be analyzed to investigate the ash

167

fusion characteristics [45]. The mineral composition of synthetic ashes with different

168

S/A ratios (S/A is 0.5, 1.0, 1.5, 2.0, 2.5, and 3.0, respectively) at 1473 K was

169

investigated by XRD, as shown in Figure 3. When S/A is lower than 1.0, the

170

crystalline phases are mainly Ca2Al2SiO7, SiO2, Ni2SiO4, and Al6Si2O13, of which

171

SiO2, Ni2SiO4, and Al6Si2O13 have high-melting point, resulting in the high AFTs. It

172

is also found that there are no diffraction peaks of V-bearing and Fe-bearing species

173

in XRD patterns. V may be present as V2O5(l) because it melts at 963 K under 7

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

174

oxidizing atmosphere, and Fe may be in the form of Fe-bearing amorphous matters.

175

As S/A reaches 1.5, the diffraction peaks of mullite disappear, which may decrease

176

the AFTs sharply. When S/A further increases (above 1.5), the main mineral phases

177

Ca2Al2SiO7, SiO2, and Ni2SiO4 keep stable. Regarding the slight increase in AFTs, it

178

may be ascribed to the increased content of high-melting SiO2.

179

To further study the mineral transformation and its influence on AFTs, the

180

theoretical mineral composition of synthetic ashes with different S/A ratios was

181

calculated at 1473 K by thermodynamic FactSage modeling. Figure 4 shows the

182

variations in theoretical mineral composition and their content of synthetic ashes.

183

When S/A is 0.5, the formation of Ni2SiO4 and Al6Si2O13 does not occur through

184

FactSage simulation. FactSage thermodynamic calculations just identify the possible

185

chemical reactions from the perspective of thermodynamics. The reactions with small

186

∆G occur more easily. Table 3 indicates that ∆G for the formation of Al6Si2O13 is

187

higher than that of Ca2Al2SiO7, Ca3Fe2Si3O12, CaAl12O19, and NiCaSi2O6, which

188

implies that the formation of Al6Si2O13 is unfavorable. Si exists in the form of

189

Ca2Al2SiO7, and Al forms CaAl12O19 and Al2Fe2O6. Also, V2O5(l), NiO(g), and

190

Fe(VO3)2 are generated according to calculation results. When S/A reaches 1.5,

191

mineral phases predicted are mainly Ca2Al2SiO7, Fe(VO3)2, SiO2, and Ni2SiO4, which

192

is basically consistent with the XRD results. Diffraction peaks of Fe(VO3)2 do not

193

appear, this may be because Fe(VO3)2 is thermodynamically unstable. With S/A

194

further increasing, the relative proportions of SiO2 and Ni2SiO4 increase gradually,

195

whereas there is a rapid decline for Ca2Al2SiO7 from 49.1% (S/A is 1.5) to 30.9%

196

(S/A is 3.0).

197

In the process of ash fusion, mineral transformation with increasing temperature

198

will influence the ash fusibility. The mineral evolution of the synthetic ash with the 8

ACS Paragon Plus Environment

Page 8 of 34

Page 9 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

199

S/A of 1.5 from 1273 to 1573 K was determined by XRD, as shown in Figure 5. The

200

ash slag between 1273 and 1373 K is composed of SiO2, Ni2SiO4, Al6Si2O13, and

201

Ca2Al2SiO7. It should be mentioned that the variations of mineral diffraction peaks in

202

XRD patterns are positively proportional to the change trend of mineral content

203

[16,46,47]. With increasing temperature, the content of SiO2 decreases gradually since

204

the diffraction peak height of SiO2 declines markedly, and its diffraction peaks

205

disappear completely at 1573 K. Also, the diffraction peaks of Al6Si2O13 disappear

206

when the temperature reaches to 1473 K. The reason may be that Al6Si2O13 reacts

207

with other minerals, such as Fe-bearing species, to form amorphous matters.

208

Ca2Al2SiO7 and Ni2SiO4 are the stable crystal phases above 1473 K.

209

Phase assemblage of the synthetic ash with the S/A of 1.5 at different

210

temperatures calculated by FactSage is present in Figure 6. At 1273 K, the main

211

mineral phases predicted are Ca2Al2SiO7, Fe(VO3)2, V2O5(l), Ni2SiO4, and SiO2, of

212

which the diffraction peaks of Ca2Al2SiO7, Ni2SiO4, and SiO2 are found in XRD

213

patterns. In contrast, Fe(VO3)2 is not formed according to experimental results. With

214

the temperature further increasing, Ni2SiO4 decomposes and transforms into NiO(g)

215

gradually. There is a slight increase for SiO2 due to the decomposition of Ni2SiO4,

216

which is contrary to the results of XRD patterns. In actual ash fusion process, SiO2

217

may form some amorphous matters, leading to the decrease of SiO2. Ca2Al2SiO7

218

keeps thermodynamically stable (49.1%) within the entire temperature range.

219

3.3. Effect of (SiO2+Al2O3) on AFTs.

220

The AFTs of synthetic ash samples in Group 2 against the addition of

221

(SiO2+Al2O3) is given in Figure 7. It can be seen that the variations of AFTs are

222

strongly dependent on the addition of (SiO2+Al2O3). When the addition is 20%, the

223

ash sample has a relatively low AFT (FT is below 1473 K). As the addition reaches to 9

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 10 of 34

224

30%, AFT shows a sharp increase, of which DT rises from 1343 to 1487 K. With the

225

addition further increasing, AFTs follow a slight increase.

226

3.4. Effect of (SiO2+Al2O3) on Mineral Transformation Behavior at High

227

Temperatures.

228

XRD patterns of synthetic ashes with different (SiO2+Al2O3) ratios heated at

229

1473 K are given in Figure 8. It can be seen that crystalline phases closely resemble

230

those formed in synthetic ashes with different S/A (Figure 3), i.e., Ca2Al2SiO7,

231

Ni2SiO4, SiO2, and Al6Si2O13 are the main minerals. When (SiO2+Al2O3) is 20%, the

232

mineral phases consist of Ca2Al2SiO7, Ni2SiO4, and SiO2. Then, as the addition

233

reaches to 30%, the diffraction peaks of CaAl2Si2O8 appear in comparison to the

234

synthetic ashes with different S/A following the reaction:

235

Ca2Al2SiO7 +3SiO2 +Al2O3 =2CaAl2Si2O8 .

(1)

236

With the (SiO2+Al2O3) further increasing to 50%, Ca2Al2SiO7, Ni2SiO4, SiO2, and

237

CaAl2Si2O8 keep thermodynamically stable, and the formation of Al6Si2O13 occurs

238

because of the increased content of SiO2 and Al2O3. With regard to the variations in

239

AFTs of synthetic ashes in Group 2, the formation of CaAl2Si2O8 and Al6Si2O13 and

240

the increased content of SiO2 may cause the continuous increase of AFTs.

241

The theoretical mineral phases of synthetic ashes with different (SiO2+Al2O3)

242

calculated by FactSage are present in Figure 9. In comparison to the XRD results, two

243

minerals CaAl2Si2O8 and Al6Si2O13 are not predicted within the entire (SiO2+Al2O3)

244

range. But NiCaSi2O6, Fe(VO3)2, V2O5(l), and Al2SiO5 are formed through

245

calculations. There is a linear rise for Ca2Al2SiO7 from 18.2% ((SiO2+Al2O3) is 20%)

246

to 44.7% ((SiO2+Al2O3) is 50%), with a sharp decline to 34.7% ((SiO2+Al2O3) is

247

60%). The decreased content is ascribed to the formation of Al2SiO5. The SiO2 10

ACS Paragon Plus Environment

Page 11 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

248

content increases monotonically within the (SiO2+Al2O3) range of 20-60%. In

249

addition, Fe(VO3)2 and V2O5(l) are predicted to form, whereas no diffraction peaks of

250

V-bearing and Fe-bearing species appear in XRD patterns, indicating that V and Fe

251

may be present as amorphous matters.

252

The mineral composition of the synthetic ash with the addition of 40%

253

(SiO2+Al2O3) heated from 1273 to 1573 K is given in Figure 10. The mineral

254

transformation is not influenced markedly by temperature since the mineral phases

255

SiO2, Ni2SiO4, Ca2Al2SiO7, and CaAl2Si2O8 formed in the process of ash fusion

256

remain unchanged within the temperature range of 1273-1473 K. When the

257

temperature rises to 1573 K, the diffraction peaks of CaAl2Si2O8 disappear while the

258

others keep stable. It is also found that the content of SiO2 and Ca2Al2SiO7 decreases

259

to some extent at 1573 K according to the variations of diffraction peaks of these two

260

species. The reason may be that partial SiO2 and Ca2Al2SiO7 form eutectics with other

261

minerals at high temperatures.

262

Figure 11 presents the phase assemblage of the synthetic ash with the

263

(SiO2+Al2O3) of 40% calculated from 1273 to 1573 K. It is found that the mineral

264

phases predicted are basically consistent with those from the synthetic ash with the

265

S/A of 1.5 (Figure 6). The existing discrepancy is that the formation of NiCaSi2O6

266

occurs between 1373 and 1473 K, and CaSiO3 is formed at 1573 K. On the basis of

267

simulation results, Ca2Al2SiO7 keeps unchanged (36.4%) within the temperature

268

range. CaAl2Si2O8 that detected in XRD patterns is not predicted to form. The content

269

of Ni2SiO4 decreases monotonically due to the formation of NiCaSi2O6 and NiO(g).

270

For SiO2, it shows a continuously saltatory change.

271

3.5. Surface Morphologies of Quenched Ash Samples.

11

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

272

In addition to mineral transformation, ash fusion characteristics can be also

273

reflected by the variations in surface morphologies of high-temperature ash slag

274

[48,49]. It is well known that the quenched ash can prevent crystal segregation and

275

phase transformation, and keep the high-temperature ash morphologies well [50].

276

Moreover, the high melted particles have the smooth surface and dense layer structure

277

[17]. Figure 12 shows the variations in surface morphologies of synthetic ashes with

278

different S/A and (SiO2+Al2O3) quenched at 1473 K. When the addition of S/A and

279

(SiO2+Al2O3) is 0.5 and 60%, respectively, the ashes consist of many fine and

280

irregular particles, which presents the rough surface and loose structure. As the S/A

281

and (SiO2+Al2O3) are 3.0 and 40%, respectively, fine particles have been

282

agglomerated into some large particles, and these particles show a dense layer

283

structure. When the addition of S/A and (SiO2+Al2O3) changes to 1.5 and 20%,

284

respectively, particles are almost in complete agglomeration, and the surface turns to

285

be more smooth. It is also observed that some protuberances are generated in the

286

molten surface of ash. On the basis of the preceding analyses, it is concluded that the

287

molten extent of ashes varies in the following orders: S/A=1.5 > S/A=3.0 > S/A=0.5,

288

(SiO2+Al2O3)=20% > (SiO2+Al2O3)=40% > (SiO2+Al2O3)=60%. These are same as

289

the variations of AFTs in Figures 2 and 7.

290

4. CONCLUSIONS

291

The effects of S/A and (SiO2+Al2O3) on synthetic petcoke ash fusibility were

292

investigated in this study. A series of analytical technologies including AFT tests,

293

XRD, SEM, and FactSage were applied to determine the AFTs, mineral

294

transformation, and surface morphologies of the high-temperature ashes. The main

295

conclusions are as follows:

12

ACS Paragon Plus Environment

Page 12 of 34

Page 13 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

296

(1) The AFTs of synthetic ash samples are closely related to the addition of S/A

297

and (SiO2+Al2O3). AFTs drop sharply with increasing S/A until it reaches 1.5, and

298

then follow a slight increase. With the (SiO2+Al2O3) increasing from 20 to 60%,

299

AFTs show a continuous increase.

300

(2) The mineral transformation during ash fusion leads to the variations in AFTs.

301

The dominant crystalline phases formed in high-temperature ashes with different S/A

302

and (SiO2+Al2O3) are Ca2Al2SiO7, SiO2, Ni2SiO4, and Al6Si2O13. The decline of

303

high-melting Al6Si2O13 may cause the sharp decrease in AFTs of synthetic ashes with

304

different S/A. The formation of CaAl2Si2O8 and Al6Si2O13 and the increased content

305

of SiO2 may contribute to the continuous increase in AFTs of synthetic ashes with

306

different (SiO2+Al2O3).

307

(3) When the addition of S/A and (SiO2+Al2O3) is 1.5 and 20%, respectively,

308

synthetic ashes have the higher molten extent. Particles in these ashes are almost

309

agglomerated completely, and present the denser layer structure and more smooth

310

surface.

311

AUTHOR INFORMATION

312

Corresponding Author

313

E-mail address: [email protected]

314

ACKNOWLEDGEMENTS

315

The authors gratefully acknowledge the financial support of the National Natural

316

Science Foundation of China (No. 21576276).

317

REFERENCES

318

(1) Zhan, X. L.; Jia, J.; Zhou, Z. J.; Wang, F. C. Influence of blending methods on the

319

co-gasification reactivity of petroleum coke and lignite. Energy Conversion and

320

Management 2011,52,1810-1814. 13

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

321

(2) Liu, X.; Zhou, Z.; Hu, Q.; Dai, Z.; Wang, F. Experimental study on co-gasification

322

of coal liquefaction residue and petroleum coke. Energy Fuels 2011,25, 3377-3381.

323

(3) Li, J. Z.; Zhao, J. T.; Zhang, L. X.; Liu, T.; Fang, Y. T. Transformation behavior of

324

vanadium in petroleum coke during high temperature CO2-gasification. Fuel 2017,

325

194, 83-90.

326

(4) Zou, J. H.; Yang, B.; Gong, K.; Wu, S.; Zhou, Z. J.; Wang, F. C.; Yu, Z. H. Effect

327

of mechanochemical treatment on petroleum coke-CO2 gasification. Fuel 2008, 87(6),

328

622-627.

329

(5) Xu, J.; Zhao, F.; Guo, Q. H.; Yu, G. S.; Liu, X.; Wang, F. C. Characterization of

330

the melting behavior of high-temperature and low-temperature ashes. Fuel Processing

331

Technology 2015, 134, 441-446.

332

(6) Shao, J. G; Lee, D. H.; Yan, R.; Liu, M.; Wang, X. L.; Liang, D. T.; White, T. J.;

333

Chen, H. P. Agglomeration characteristics of sludge combustion in a bench-scale

334

fluidized bed combustor. Energy Fuels 2007, 21, 2608-2614.

335

(7) Xu, J.; Yu, G. S.; Liu, X.; Zhao, F.; Chen, X.; Wang, F. C. Investigation on the

336

high-temperature flow behavior of biomass and coal blended ash. Bioresource

337

Technology 2014, 166, 494-499.

338

(8) Yan, T.G.; Kong, L. X.; Bai, J.; Bai, Z. Q.; Li, W. Thermomechanical analysis of

339

coal ash fusion behavior. Chemical Engineering Science 2016, 147, 74-82.

340

(9) Gupta, R. P.; Wall, T. F.; Kajigaya, I.; Miyamae, S.; Tsumita, Y.

341

Computer-controlled scanning electron microscopy of minerals in coal-Implications

342

for ash deposition. Progress in Energy and Combustion Science 1998, 24, 523-543.

343

(10) Benson, S. A.; Sondreal, E. A.; Hurley, J. P. Status of coal ash behavior research.

344

Fuel Processing Technology 1995, 44, 1-12.

14

ACS Paragon Plus Environment

Page 14 of 34

Page 15 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

345

(11) Folgueras, M. B.; Alonso, M.; Folgueras, J. R. Modification of lignite ash fusion

346

temperatures by the addition of different types of sewage sludge. Fuel Processing

347

Technology 2015, 131, 348-355.

348

(12) Chakravarty, S.; Mohanty, A.; Banerjee, A.; Tripathy, R.; Mandal, G. K.;

349

Basariya, M. R.; Sharma, M. Composition, mineral matter characteristics and ash

350

fusion behavior of some Indian coals. Fuel 2015, 150, 96-101.

351

(13) Bryant, G. W.; Browning, G. J.; Gupta, S. K.; Lucas, J. A.; Gupta, R. P.; Wall, T.

352

F. Thermomechanical analysis of coal ash: the influence of the material for the sample

353

assembly. Energy Fuels 2000, 14, 326-335.

354

(14) Boccaccini, A. R.; Hamann, B. Review in situ high-temperature optical

355

microscopy. Journal of Materials Science 1999, 34, 5419-5436.

356

(15) Gupta, R. P. Advanced coal characterization: A review. Energy Fuels 2007,

357

21(2), 451-460.

358

(16) Vassilev, S. V.; Kltano, K.; Takeda, S.; Tsurue, T. Influence of mineral and

359

chemical-composition of coal ashes on their fusibility. Fuel Processing Technology

360

1995, 45, 27-51.

361

(17) Liu, B.; He, Q. H.; Jiang, Z. H.; Xu, R. F.; Hu, B. X. Relationship between coal

362

ash composition and ash fusion temperatures. Fuel 2013, 105, 293-300.

363

(18) Wang, Y.; Xiang, Y.; Wang, D. X.; Dong, C. Q.; Yang, Y. P.; Xiao, X. B.; Lu, Q.;

364

Zhao, Y. Effect of sodium oxides in ash composition on ash fusibility. Energy Fuels

365

2016, 30(2), 1437-1444.

366

(19) van, Dyk J. C. Understanding the influence of acidic components (Si, Al, and Ti)

367

on ash flow temperature of South African coal sources. Minerals Engineering 2006,

368

19(3), 280-286.

15

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

369

(20) Reinmoller, M.; Klinger, M.; Schreiner, M.; Gutte, H. Relationship between ash

370

fusion temperatures of ashes from hard coal, brown coal, and biomass and mineral

371

phases under different atmospheres: A combined FactSageTM computational and

372

network theoretical approach. Fuel 2015, 151, 118-123.

373

(21) Rizvi, T.; Xing, P.; Pourkashanian, M.; Darvell, L. I.; Jones, J. M.; Nimmo, W.

374

Prediction of biomass ash fusion behavior by the use of detailed characterization

375

methods coupled with thermodynamic analysis. Fuel 2015, 141, 275-284.

376

(22) Jak, E. Prediction of coal ash fusion temperatures with the F*A*C*T

377

thermodynamic computer package. Fuel 2002, 81, 1655-1668.

378

(23) Bryers, R. W. Utilization of petroleum coke and petroleum coke/coal blends as a

379

means of steam raising. Fuel Processing Technology 1995, 44(1-3), 121-141.

380

(24) Li, J. Z.; Zhao, J. T.; Dai, X.; Bai, J.; Fang, Y. T. Effect of vanadium on the

381

petroleum coke ash fusibility. Energy Fuels 2017,31(3), 2530-2537.

382

(25) Li, J. Z.; Chen, X. D.; Liu, Y. B.; Xiong, Q. A.; Zhao, J. T.; Fang, Y. T. Effect of

383

ash composition (Ca, Fe, and Ni) on the petroleum coke ash fusibility. Energy Fuels

384

2017, 31, 6917-6927.

385

(26) Mysen, B. O. The structure of silicate melts. Ann. Rev. Earth Planet. Sci. 1983,

386

11, 75-97.

387

(27) Jiang, Y.; Lin, X. C.; Ideta, K.; Takebe, H.; Miyawaki, J.; Yoon, S. H; Mochida, I.

388

Microstructural transformations of two representative slags at high temperatures and

389

effects on the viscosity. Journal of Industrial and Engineering Chemistry 2014, 20,

390

1338-1345.

391

(28) Su, S.; Pohl, J. H.; Holcombe, D. Fouling propensities of blended coals in

392

pulverized coal-fired power station boilers. Fuel 2003, 82, 1653-1667.

16

ACS Paragon Plus Environment

Page 16 of 34

Page 17 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

393

(29) Winegartner, E. C. Coal fouling & slagging parameters. ASME (Book H-86),

394

1974.

395

(30) Miller, B. G. Coal energy systems. Burlington: Elsevier Academic Press, 2005. p.

396

232-236.

397

(31) Xuan, W. W.; Whitty, K. J.; Guan, Q. L.; Bi, D. P.; Zhan, Z. H.; Zhang, J. S.

398

Influence of SiO2/Al2O3 on crystallization characteristics of synthetic coal slags. Fuel

399

2015, 144, 103-110.

400

(32) Yan, T. G.; Bai, J.; Kong, L. X.; Bai, Z. Q.; Li, W.; Xu, J. Effect of SiO2/Al2O3 on

401

fusion behavior of coal ash at high temperature. Fuel 2017, 193, 275-283.

402

(33) Hurst, H. J.; Novak, F.; Patterson, J. H. Viscosity measurements and empirical

403

predictions for fluxed Australian bituminous coal ashes. Fuel 1999, 78, 1831-1840.

404

(34) Xuan, W. W.; Whitty, K. J.; Guan, Q. L.; Bi, D. P.; Zhan, Z. H.; Zhang, J. S.

405

Influence of CaO on crystallization characteristics of synthetic coal slags. Energy

406

Fuels 2014, 28(10), 6627-6634.

407

(35) Kalmanovitch, D. P.; Williamson, J. Crystallization of coal ash melts. ACS 1986,

408

301, 234–55.

409

(36) Vorres, K. S.; Greenberg, S. Viscosity of synthetic coal ash slags. ACS 1986, 301,

410

156–69.

411

(37) A.S.o.t.I.A.f.T.a.M. ASTM International: 2013.

412

(38) GB/T 219-2008, Determination of fusibility of coal ash, National Standards of

413

the People’s Republic of China, 2008.

414

(39) Li, J. Z.; Xiong, Q. A.; Shan, J.; Zhao, J. T.; Fang, Y. T. Investigating a high

415

vanadium petroleum coke ash fusibility and its modification. Fuel 2018, 211,

416

767-774.

17

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 18 of 34

417

(40) Nakano, J.; Sridhar, S.; Moss, T., Bennett, J.; Kwong, K. S. Crystallization of

418

synthetic coal-petcoke slag mixtures simulating those encountered in entrained bed

419

slagging gasifiers. Energy Fuels 2009, 23, 4723-4733.

420

(41) Nakano, J.; Kwong, K. S.; Bennett, J.; Lam, T.; Fernandez, L.; Komolwit, P.;

421

Sridhar,

422

(Al2O3-CaO-FeO-SiO2-V2O3) under simulated gasification conditions. Energy Fuels

423

2011, 25, 3298-3306.

424

(42) Nakano, J.; Duchesne, M.; Bennett, J.; Kwong, K. S.; Nakano, A.; Hughes, R.

425

Thermodynamic effects of calcium and iron oxides on crystal phase formation in

426

synthetic gasifier slags containing from 0 to 27 wt.% V2O3. Fuel 2015, 161, 364-375.

427

(43) Harb, J. N.; Munson, C. L.; Richards, G. H. Use of equilibrium calculations to

428

predict the behavior of coal ash in combustion systems. Energy Fuels 1993, 7(2),

429

208-214.

430

(44) Wei, X. L.; Lopez, C.; Von, Puttkamer T.; Schnell, U.; Unterberger, S.; Hein, K.

431

R. G. Assessment of chlorine-alkali-mineral interactions during co-combustion of

432

coal and straw. Energy Fuels 2002, 16(5),1095-1108.

433

(45) Li, F. H.; Fang, Y. T. Ash fusion characteristics of a high aluminum coal and its

434

modification. Energy Fuels 2016, 30(4), 2925-2931.

435

(46) Yang, J. K.; Xiao, B.; Boccaccini, A. R. Preparation of low melting temperature

436

glass-ceramics from municipal waste incineration fly ash. Fuel 2009, 88(7),

437

1275-1280.

438

(47) Wu, X. J.; Zhang, Z. X.; Piao, G. L.; He, X.; Chen, Y. S.; Kobayashi, N.; Mori, S.;

439

Itaya, Y. Behavior of mineral matters in Chinese coal ash melting during

440

char-CO2/H2O gasification reaction. Energy Fuels 2009, 23, 2420-2428.

S.

Phase

equilibria

in

synthetic

18

ACS Paragon Plus Environment

coal-petcoke

slags

Page 19 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

441

(48) Li, F. H.; Xu, M. L.; Wang, T.; Fang, Y. T.; Ma, M. J. An investigation on the

442

fusibility characteristics of low-rank coals and biomass mixtures. Fuel 2015, 158,

443

884-890.

444

(49) Li, F. H.; Fang, Y. T. Modification of ash fusion behavior of lignite by the

445

addition of different biomasses. Energy Fuels 2015, 29, 2979-2986.

446

(50) Wang, Z. G.; Bai, J.; Kong, L. X.; Bai, Z. Q.; Li, W. Effect of V and Ni on ash

447

fusion temperatures. Energy Fuels 2013, 27(12), 7303-7313.

Table 1. Ash Composition of Five Real Petcoke (wt %) Petcoke

V2O5

Shanxi

33.89 7.55

NiO

SiO2

Al2O3

Fe2O3 CaO

MgO

TiO2

SO3

K2O Na2O

P2O5

20.20 10.54 7.40

13.92 1.18

0.83

0.75

0.76

1.74

0.54

Wuhan

28.58 10.52 21.35 11.36 4.36

17.33 1.85

0.74

0.89

0.81

1.15

0.60

Zhenhai

29.82 12.37 25.44 7.60

10.12 8.79

1.21

0.35

1.35

0.96

0.98

0.32

Zibo

31.04 6.87

18.35 6.11

11.79 19.41 0.99

0.55

1.64

0.84

0.74

0.78

Daqing

32.35 9.75

17.74 7.04

5.35

0.64

0.97

1.35

1.05

0.61

21.35 0.74

19

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 20 of 34

Table 2. Chemical Composition of Synthetic Ash Samples composition (wt %) SiO2

Al2O3

V2 O5

NiO

Fe2O3

CaO

S/A SiO2+ Al2O3

1.1

15.33

30.67

30.00

8.00

6.00

10.00

0.5

46.00

1.2

23.00

23.00

30.00

8.00

6.00

10.00

1.0

46.00

1.3

27.60

18.40

30.00

8.00

6.00

10.00

1.5

46.00

1.4

30.67

15.33

30.00

8.00

6.00

10.00

2.0

46.00

1.5

32.86

13.14

30.00

8.00

6.00

10.00

2.5

46.00

1.6

34.50

11.50

30.00

8.00

6.00

10.00

3.0

46.00

2.1

13.33

6.67

40.00

15.00

10.00

15.00

2.0

20.00

2.2

20.00

10.00

36.00

13.00

8.00

13.00

2.0

30.00

2.3

26.67

13.34

31.00

11.00

7.00

11.00

2.0

40.00

2.4

33.33

16.67

27.00

9.00

5.00

9.00

2.0

50.00

2.5

40.00

20.00

23.00

7.00

3.00

7.00

2.0

60.00

groups

no.

Group 1

Group 2

20

ACS Paragon Plus Environment

Page 21 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

21

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 1. The schematic representation of the furnace apparatus

22

ACS Paragon Plus Environment

Page 22 of 34

Page 23 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

Figure 2. Effect of S/A on the AFTs.

23

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 3. XRD patterns of the synthetic ashes with different S/A at 1473 K.

24

ACS Paragon Plus Environment

Page 24 of 34

Page 25 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

Figure 4. Effect of S/A on mineral transformation calculated by FactSage at 1473 K.

25

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 5. XRD patterns of synthetic ash with the S/A of 1.5 from 1273 to 1573 K.

26

ACS Paragon Plus Environment

Page 26 of 34

Page 27 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

Figure 6. Effect of temperature on mineral transformation of synthetic ash with the S/A of 1.5 calculated by FactSage.

27

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 7. Effect of (SiO2+Al2O3) on the AFTs.

28

ACS Paragon Plus Environment

Page 28 of 34

Page 29 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

Figure 8. XRD patterns of the synthetic ashes with different (SiO2+Al2O3) at 1473 K.

29

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 9. Effect of (SiO2+Al2O3) on mineral transformation calculated by FactSage at 1473 K.

30

ACS Paragon Plus Environment

Page 30 of 34

Page 31 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

Figure 10. XRD patterns of synthetic ash with the (SiO2+Al2O3) of 40% from 1273 to 1573 K.

31

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 11. Effect of temperature on mineral transformation of synthetic ash with the (SiO2+Al2O3) of 40% calculated by FactSage

32

ACS Paragon Plus Environment

Page 32 of 34

Page 33 of 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

S/A=0.5

Si+Al=60%

S/A=3.0

Si+Al=40%

S/A=1.5

Si+Al=20%

(a)

(b)

33

ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 12. SEM photomicrographs of synthetic ashes with different S/A (a) and (SiO2+Al2O3) (b) at 1473 K.

34

ACS Paragon Plus Environment

Page 34 of 34