Effects of Cationic Polypeptide on CaCO3 Crystallization and Sand

The effects of poly-Lys on sand solidification were also investigated by syringe ..... Bridge formation between sand grains is also important for prev...
0 downloads 0 Views 8MB Size
Subscriber access provided by READING UNIV

Article

Effects of cationic polypeptide on CaCO3 crystallization and sand solidification by microbial-induced carbonate precipitation Thiloththama Hiranya Kumari Nawarathna, Kazunori Nakashima, Masahiro Fujita, Momoko Takatsu, and Satoru Kawasaki ACS Sustainable Chem. Eng., Just Accepted Manuscript • DOI: 10.1021/acssuschemeng.8b01658 • Publication Date (Web): 13 Jul 2018 Downloaded from http://pubs.acs.org on July 17, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

1

Effects of cationic polypeptide on CaCO3 crystallization and sand solidification by

2

microbial-induced carbonate precipitation

3 4

Thiloththama H. K. Nawarathna§, Kazunori Nakashima‡*, Masahiro Fujita§, Momoko

5

Takatsu§, Satoru Kawasaki‡

6 7

§

8

University, Kita 13, Nishi 8, Kita-Ku, Sapporo, 060-8628, Japan

9



10

Division of Sustainable Resources Engineering, Graduate School of Engineering, Hokkaido

Division of Sustainable Resources Engineering, Faculty of Engineering, Hokkaido

University, Kita 13, Nishi 8, Kita-Ku, Sapporo, 060-8628, Japan

11 12 13 14

*Corresponding author (K. Nakashima)

15

TEL./FAX: +81-11-706-6322

16

E-mail: [email protected]

17

1 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 2 of 35

18

ABSTRACT

19

The use of organic additives to improve microbial-induced carbonate precipitation (MICP) is

20

a novel and innovative idea. This study is the first to address the effects of the cationic

21

biopolymer poly-lysine (poly-Lys) on CaCO3 crystallization and sand solidification by MICP.

22

CaCO3 was precipitated with and without poly-Lys by hydrolysis of urea by using ureolytic

23

bacteria, Pararhodobacter sp., in the presence of CaCl2 under different experimental

24

conditions. The morphologies and polymorphs of the oven-dried precipitates were

25

investigated using scanning electron microscopy and X-ray diffraction. A larger amount of

26

precipitate was obtained with poly-Lys than with the conventional MICP method. The curve

27

for the relationship between the poly-Lys concentration and amount of precipitate was bell

28

shaped. In the presence of poly-Lys, the morphology changed from rhombohedral crystals to

29

twin spherical crystals. The effects of poly-Lys on sand solidification were also investigated

30

by syringe solidification at different bacterial injection intervals with and without poly-Lys.

31

The addition of poly-Lys gave strongly cemented sand specimens that were stronger than

32

those obtained by the conventional method. The results confirm that poly-Lys addition is an

33

effective and sustainable way to improve the MICP efficiency and production of green

34

materials for engineering applications.

35 36

KEYWORDS: Biocement, Biomineral, Calcium Carbonate, Morphology, Poly-Lysine

2 ACS Paragon Plus Environment

Page 3 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

37

INTRODUCTION

38

The amount of suitable land available for construction is decreasing because of rapid

39

population growth and urbanization. Unsuitable ground is therefore being used for building

40

constructions and appropriate ground improvement techniques are needed to improve the

41

properties of weak soils. The available traditional ground improvement techniques have

42

various limitations and most of these methods are environmentally unfriendly. Recently,

43

biological approaches have attracted attention as environmentally friendly ground

44

improvement methods.

45

One innovative idea is to use non-pathogenic microorganisms that are naturally present

46

in the subsurface soil to improve the properties of uncemented soils.1 These microorganisms

47

support to provide the cementing materials through enzymatic reactions. CaCO3 is a well-

48

known cementing material and a common biomineral. The formation of artificial CaCO3 as a

49

cementing material via biological processes is an ecofriendly method for treating uncemented

50

soils. This concept is called microbial-induced carbonate precipitation (MICP) and this bio-

51

cement can be introduced as a sustainable construction material.2 MICP is a bio-geochemical

52

process in which CaCO3 precipitation in the soil matrix is achieved by urea hydrolysis using

53

enzyme urease, which is produced by ureolytic bacteria. The overall process involves the

54

biochemical reactions represented by equations 1–3.3-8 The precipitated CaCO3 acts as a

55

binding material, which binds soil grains together at the particle–particle interfaces, leading

56

to increased soil stiffness and strength.



CONH  + H O  H NCOO + NH 1 H NCOO + H O → HCO  + NH 2 Ca + HCO + NH → CaCO + NH 3 57

Previous research has shown that MICP can increase the soil strength and stiffness, and

58

maintain its permeability, with minimum disturbance to the soil.1,8-11 CaCO3 precipitation is 3 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 4 of 35

59

governed by four major factors: calcium concentration, carbonate concentration, pH, and

60

availability of nucleation sites.11 The MICP efficiency can be improved by adjusting these

61

parameters with suitable chemicals, but adding chemicals to improve the efficiency can

62

damage the environment. It is therefore better to use naturally formed environmentally

63

friendly additives. The use of naturally formed organic additives to improve the MICP

64

performance is therefore attractive. In nature, biominerals are mainly deposited in organic

65

matrixes that consist mainly of macromolecules such as proteins or polysaccharides, which

66

act as templates for mineral nucleation and growth.12-14 It has been proven that combinations

67

of inorganic minerals and organic macromolecules provide good hybrid materials with well-

68

controlled morphologies, structures, and unique properties.15-18 In the present study, we

69

mimicked this concept to improve the efficiency of MICP by producing new bio-inspired

70

materials.

71

Previous studies have shown the effects of acidic polypeptides on CaCO3

72

crystallization,19-22 but there are few reports of the use of basic polypeptides to control CaCO3

73

crystallization.15,20 This study is the first to address the effects of a cationic polypeptide on

74

CaCO3 crystallization and the MICP process by using the ureolytic bacteria Pararhodobacter

75

sp. Most of the MICP related research works were based on the Sporosarcina pasteurii,

76

which is Gram positive bacteria with high urease activity.11, 23 Similar to S. pasteurii, Gram

77

negative Pararhodobacter sp has been successfully applied in sand solidification 4,10,24 due to

78

its high urease activity and long term stability.6 Poly-lysine (poly-Lys) was used as the

79

cationic polypeptide; at neutral pH its amino group side chains are positively charged.20

80 81 82

4 ACS Paragon Plus Environment

Page 5 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

83

EXPERIMENTAL SECTION

84

Preparation of bacterial cell culture

85

Ureolytic bacteria Pararhodobacter sp. isolated from beach sand in Sumuide, Nago,

86

Okinawa, Japan was used in this study.25,26 Bacterial cells were pre-cultured in Zobell 2216E

87

medium (polypeptone (Nihon Seiyaku Co., Ltd., Tokyo, Japan) 5.0 g/L, yeast extract (BD

88

Biosciences Advanced Bioprocessing, Miami, FL, USA) 1.0 g/L, FePO4 (Junsei Chemical

89

Co., Ltd., Tokyo, Japan) 0.1 g/L in artificial sea water, pH 7.6–7.8; 5 mL) by shaking at

90

30 °C and 160 rpm for 24 h. The pre-culture (1 mL) was inoculated into fresh Zobell 2216E

91

medium (100 mL). The mixture was kept in the shaking incubator under the same conditions

92

as those used for pre-culturing for 48 h. The cells were collected by centrifugation of the

93

bacterial culture. The cells were resuspended in sterilized water to adjust the cell

94

concentration (OD600 = 1), which was determined by UV-visible spectroscopy (V-730,

95

JASCO Corporation, Tokyo, Japan).

96 97

Precipitation of CaCO3 by ureolytic bacteria

98

CaCO3 precipitation was achieved by urea hydrolysis with bacteria in the presence of

99

CaCl2. The bacteria were added to a substrate solution containing urea (0.3 mol/L; Wako

100

Pure Chemical Industries Ltd., Tokyo, Japan) and CaCl2 (0.3 mol/L; Wako Pure Chemical

101

Industries Ltd., Tokyo, Japan) in the presence or absence of poly-Lys (Wako Pure Chemical

102

Industries Ltd., Tokyo, Japan). The reaction mixture (10 mL) was shaken at 30 °C and 160

103

rpm for 24 h. The samples were centrifuged to separate the CaCO3 precipitate from the

104

supernatant. The precipitates were dried in an oven at 100 °C for 24 h, and then the dry

105

weights of the precipitates were determined. The reactions were performed at various

106

bacterial concentrations (OD600 = 0.01–0.2) in the presence (10 mg/L) or absence of poly-Lys.

5 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 6 of 35

107

The same reactions were conducted at various poly-Lys concentrations (0-50 mg/L) with a

108

bacterial concentration of OD600 = 0.1. All experiments were done in triplicate.

109 110

X-ray diffraction and scanning electron microscopy analyses

111

The polymorphs of the CaCO3 precipitate were identified by X-ray diffraction (XRD;

112

MiniFlex™, Rigaku Co., Ltd., Tokyo, Japan) analysis of ground samples under Ni-filtered

113

Cu 1.5406 Å radiation. The crystalline phases were identified with MATCH 3.4 software.

114

Scanning electron microscopy (SEM; Miniscope TM3000, Hitachi, Tokyo, Japan) was used

115

to investigate the morphologies of the precipitated CaCO3 crystals.

116 117

Sand solidification in syringe

118

Sand solidification in syringe was performed with or without poly-Lys to check the

119

effects of the polymer on sand solidification under various conditions, as shown in Table 1.

120

The method previously described by Danjo and Kawasaki was used for the experiments.24

121

Mikawa sand (40 g, mean diameter D50 = 0.6 mm) was oven dried at 110 °C for 2 days

122

and placed in a 35 mL syringe (mean diameter D50 = 2.5 cm and height 7 cm) in three layers.

123

Each layer was subjected to 20 hammer blows. Then first poly-Lys (5 ml, 100 mg/L) was

124

injected to the syringe and next bacterial solution (16 mL, OD600 = 1) was injected and kept

125

it 5-10 min to allow fixation of the bacteria to sand particles. After that, drained out the

126

solution from the outlet, leaving 2 mL of the solution above the surface. After that

127

cementation solution (20 mL; 0.3 M urea, 0.3 M CaCl2, 0.02 M sodium hydrogen carbonate,

128

0.2 M ammonium chloride, and 3 g/L nutrient broth (BD Biosciences Advanced

129

Bioprocessing, Miami, FL, USA)) was injected into the syringe, and drained, leaving 2 mL of

130

the solution above the surface to maintain wet conditions. All solutions were injected through

6 ACS Paragon Plus Environment

Page 7 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

131

gravity. Ammonium chloride was added to the cementation solution as a nitrogen source of

132

the bacteria. Experiments were done in triplicate in an incubator at 30 °C.

133

Every 3 days, the pH and Ca2+ concentration of the drainage were measured. The

134

experiments were conducted with various bacterial injection intervals. In one set, bacteria

135

were injected only once, on the first day. In another set, bacteria were injected twice, i.e., on

136

the first day and again after 7 days. During the experiment poly-Lys was injected twice, on

137

the first day and again after 7 days. After curing for 14 days, the unconfined compressive

138

strength (UCS) of the samples were determined with a needle penetration device (SH70,

139

Maruto Testing Machine Company, Tokyo, Japan). First, needle was injected in to the sand

140

specimen and penetration force (N) and the penetration distance (mm) were recorded.

141

Unconfined compressive strengths (UCS) of the samples were determined by using the

142

calibration equation given in equation 4 which was provided by the manufacture. In the

143

instrument manual it is mentioned that this calibration equation was developed by

144

considering 114 natural rock samples and 50 improved soils with cements. log = 0.978 log%  + 2.621 4

145

x= Penetration gradient (N/mm)

146

y= Unconfined Compressive Strength

147 148

RESULTS AND DISCUSSION

149

Effects of poly-Lys on CaCO3 precipitation

150

Figure 1 shows the amounts of CaCO3 formed by ureolytic bacteria at different

151

concentrations in the presence or absence of poly-Lys. In both cases, the amount of CaCO3

152

precipitate increased with increasing bacterial concentration. The amount of precipitate

153

formed is directly related to the urease activity of the relevant bacteria.27 The urease activity

154

of Pararhodobacter sp. increases with increasing cell concentration.6 The increase in urease

7 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 8 of 35

155

activity with increasing cell concentration leads to increased precipitation, and causes rapid

156

nucleation and growth of CaCO3 at high bacterial cell concentrations. Previous reports have

157

stated that the rate of CaCO3 precipitation with Sporosarcina pasteurii depends on the rate of

158

urea hydrolysis and to increase the rate of urea hydrolysis the ureolytic biomass must be

159

increased.8 A higher concentration of urease also increases the CaCO3 formation rate.14

160

The amount of precipitate formed in the system with poly-Lys was higher than that

161

formed in the absence of poly-Lys. The positive effect of poly-Lys on CaCO3 precipitation is

162

clearer at low bacterial concentrations. A significant effect of poly-Lys was not detected at

163

higher bacterial concentrations; this indicates that the bacterial activity may be the dominant

164

factor rather than the effects of poly-Lys. Acidic polypeptides clearly affect CaCO3

165

crystallization because the negative charge on the carboxylic group is strongly attracted to

166

Ca2+ and in the presence of CO32−, a CaCO3 nucleus can be formed.19,21,22,28 The effects of

167

basic polypeptides on CaCO3 crystallization are unclear and difficult to explain. One research

168

group reported chemical precipitation of CaCO3 from Ca(NO3)2 and Na2CO3 in the presence

100 μm

2−

169

of L-Lys. They suggested that the positive charge on L-Lys strongly attracts CO3

ions,

170

resulting in CO32− ion enrichment and higher super saturation of CO32− ions in local regions.

171

This is favorable for CaCO3 crystal nucleation and growth.21 The positive effect of poly-Lys

172

on CaCO3 precipitation can be similarly explained. Most acidic polypeptides inhibit CaCO3

173

nucleation and growth.12,21 However, the addition of poly-Lys does not inhibit nucleation and

174

growth of CaCO3. The interactions between poly-Lys and calcite are purely electrostatic

175

interactions between the positively charged polypeptide and the negatively charged calcite

176

surface.20,28 Poly-Lys therefore has a positive effect on CaCO3 crystallization and can be used

177

to improve the MICP efficiency.

178

The crystal morphologies of the samples prepared at various bacterial concentrations

179

were examined by SEM (Figure 2). Figure 2(a) shows that well-developed rhombohedral

8 ACS Paragon Plus Environment

Page 9 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

180

crystals were obtained at low bacterial concentrations. In contrast, at higher bacterial

181

concentrations, individual rhombohedral crystals were not be observed and rhombohedral

182

crystal agglomeration occurred. Another important point is that the crystal size decreased

183

with increasing bacterial concentration. This may be because the number of nucleation sites

184

increased with increasing bacterial concentration. Urease from Pararhodobacter sp. is not

185

secreted into the extracellular medium but accumulates in or on the cell as a membrane

186

enzyme.6 The bacterial cells can therefore act as nucleation sites for CaCO3 crystals. Because

187

of the lack of nucleation sites at low bacterial concentrations, after the initial calcite

188

precipitation on the nucleation sites, calcite crystals can grow continuously and produce

189

larger crystals.29 However, at higher bacterial concentrations, each cell acts as a nucleation

190

site and a large number of small crystals are produced, without growth of the individual

191

crystals.

192

Figure 3 shows the morphologies of the crystals in the presence of poly-Lys at various

193

bacterial concentrations. In the presence of poly-Lys, the crystal morphology became

194

ellipsoidal; this was especially clear at low bacterial concentrations. At higher bacterial

195

concentrations, a combination of ellipsoidal and rhombohedral crystals was obtained.

196

However, the XRD patterns in Figure 4 show that the main component of the obtained

197

crystals, with and without poly-Lys, was calcite.

198

Formation of larger number of smaller crystals in higher bacteria cell concentration

199

would increase the efficiency of the MICP process in the solution due to produce of larger

200

amount of CaCO3 precipitate.

201 202

Effects of poly-Lys concentration on CaCO3 crystallization

203

Figure 5 shows the amounts of precipitate formed at different concentrations of poly-

204

Lys. A moderate bell-shaped relationship was observed between the amount of precipitate

9 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 10 of 35

205

and the poly-Lys concentration. The amounts of precipitate formed at intermediate poly-Lys

206

concentrations were higher than those formed at lower and higher concentrations. Visual

207

observations indicated that when the poly-Lys concentration was high, the precipitate was a

208

gel rather than a solid. Before oven drying, the volumes of precipitates formed at high poly-

209

Lys concentrations were higher than those of the other samples, but the dry weights, i.e., after

210

oven drying, were lower than those of the other samples. A similar relationship between the

211

amount of precipitate and the poly-Lys concentration was previously reported by another

212

research group.20 In their experiments, CaCO3 was precipitated by a chemical reaction

213

between CaCl2 and Na2CO3 solutions in the presence of poly-Lys. They reported that

214

increased calcite growth at low concentrations of poly-Lys and decreased growth at higher

215

concentrations is typical of additives that are weakly, non-selectively bonded to the crystal

216

surfaces.

217

The SEM images in Figure 6 show that the crystal morphology changed greatly with

218

changes in the poly-Lys concentration. At low poly-Lys concentrations, polyhedral crystals

219

were obtained, as shown in the Figure 6(a). With increasing poly-Lys concentration, the

220

morphology changed to peanut-like twin spheres, and at high poly-Lys concentrations, twin

221

spheres were dominant, as shown in Figure 6(d). These morphology changes depend on the

222

conformation of the poly-Lys chain. During urea hydrolysis, the pH of the medium increases,

223

and under alkaline conditions poly-Lys has an α-helix confirmation.30 This α-helix

224

confirmation leads to tangentially oriented growth on the sphere surface and vertically

225

oriented growth on the equatorial zone, to form peanut-like twin spheres, as shown in Figure

226

7.15 Twin spheres are probably formed because of crystal growth on both sides of the nuclear

227

plate.

228

10 ACS Paragon Plus Environment

Page 11 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

229

ACS Sustainable Chemistry & Engineering

Sand solidification in syringe

230

Four sets of experiment (S1–S4) were performed with/without poly-Lys addition and

231

with various bacterial injection times. Figure 8 shows the Ca2+ concentrations and pH values

232

of the effluents every 3 days.

233

Initially, a negligible amount of Ca2+ was detected in the effluents of all four samples.

234

After 7 days, the effluent Ca2+ concentrations for S1 and S2 gradually increased with time,

235

but the S3 and S4 effluent Ca2+ concentrations remained low for up to 12 days. Lower Ca2+

236

concentrations in the effluent show that more Ca2+ was deposited as CaCO3 in the sand

237

column, resulting in small amounts being washed out with the effluent. The initial low Ca2+

238

concentrations in the effluents of all the samples provide evidence of initially high

239

precipitation of CaCO3 in the sand column. However, the Ca2+ concentrations in the effluents

240

in the systems without reinjection of bacteria (S1 and S2) increased gradually after 6 days,

241

indicating insufficient consumption of Ca2+ ions and low precipitation of CaCO3. In contrast,

242

the Ca2+ concentrations in the systems that were reinjected with bacteria (S3 and S4)

243

remained low, indicating efficient CaCO3 precipitation in the column.

244

The pH values for S1 and S2 decreased after 6 days, whereas the values for S3 and S4

245

were almost constant up to 12 days and then began to decline. We found a close relationship

246

between the Ca2+ concentration and effluent pH. In urea hydrolysis by urease, the pH of the

247

solution increases because of ammonia formation. The pH of the effluent therefore remained

248

high (alkaline) when the urease activity was high. However, urea hydrolysis rate decreased

249

with time due to the deactivation of the bacteria. Bacterial cells itself could act as a

250

nucleation site for CaCO3 deposition around the cell wall, leading to the gradual reduction of

251

the bacterial urease activity.31 On the other hand, reinjection of the bacteria helped to

252

maintain the active cell density hence could maintain high pH value. At high urease activity,

253

CaCO3 is efficiently formed in the column, and the Ca2+ concentration in the effluent remains

11 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 12 of 35

254

low. For Pararhodobacter sp., a significant loss of activity is seen under acidic (pH < 5) and

255

alkaline (pH > 10) conditions, and the activity is maximum at around pH 8.6 To increase

256

CaCO3 precipitation, it is therefore important to maintain the pH at around 7–8. The increase

257

in the Ca2+ concentration and the decrease in the effluent pH are therefore attributed to

258

decreased urease activity in the column. The urease activity was recovered by reinjection of

259

the bacterial culture, to maintain a low Ca2+ concentration and high pH value throughout the

260

test period.

261

Solidified sand specimens after 14 days before and after UCS measurements are given

262

in Figure 9. The estimated UCS values for the syringe solidification samples are shown

263

graphically in Figure 10. All the sand specimens were strongly cemented, according to the

264

classification system proposed by Shafii and Clough,

265

values less than 1 MPa are classified as moderately cemented soil, strongly cemented soil is

266

defined as having a UCS between 1 and 3 MPa, and samples with UCS values greater than 3

267

MPa are classified as soft rock.

32

in which cemented soils with UCS

268

One interesting point is that the strength of the sand column decreased from top to

269

bottom. This may be the result of high urease activity near the inlet, caused by accumulation

270

of bacteria near the injection point. Pararhodobacter sp. are aerobic bacteria, therefore the

271

oxygen concentration plays a significant role in the bacterial activity. Lack of oxygen in the

272

bottom of the specimen would inhibit the bacterial activity, and the strength of the specimen

273

would therefore decrease from top to bottom.4 It is important to achieve an even distribution

274

of bacterial activity throughout the sand column to obtain a homogeneous sample. Control the

275

rate of CaCO3 precipitation is also important. The injection rate of the cementation fluid

276

plays a significant role in achieving a uniform distribution of bacteria through the sand

277

column. At a low injection rate, immediate cementation can occur near the injection point.

278

Increases the flow rate beyond the rate of urea consumption, and precipitation will lead to a

12 ACS Paragon Plus Environment

Page 13 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

279

uniform distribution of chemicals along the pathway.8 However, this area has not yet been

280

well studied and it is difficult to give an exact explanation, therefore further investigation is

281

needed.

282

In this work, sand solidification was strengthened by reinjection of bacteria after 7 days.

283

Reinjection of bacteria after 7 days effectively maintained a high urea hydrolysis rate, which

284

led to higher CaCO3 precipitation and solidified sand with high UCS values. A number of

285

other factors can cause a decrease in urease activity over long time periods, e.g.,

286

encapsulation of bacteria as a result of precipitation or being trapped inside pores, a reduction

287

in chemical transport (nutrients) through pore spaces because of precipitation, and space

288

limitations caused by saturation of pore fluids and accumulation of metabolic wastes.27,29,33

289

Bacterial cell concentration also significantly affect the strength of the sample. As shown in

290

the Figure 3, a larger number of small crystals produced by higher cell concentration can

291

create favorable bridge between sand particles by filling the pore spaces more efficiently than

292

a small amount of larger crystals which were produced by lower cell concentration.

293

The most important finding of this research is the positive effect of poly-Lys on sand

294

solidification compared with the conventional method. Poly-Lys addition gave strongly

295

cemented samples with better mechanical strength. The cell adhesion properties of poly-Lys

296

could be one of the reasons for its positive effect on sand solidification. In sand solidification,

297

the pore spaces between the sand particles should be filled effectively to achieve good

298

strength. Bridge formation between sand grains is also important for preventing movement of

299

sand grains and improving the strength and stiffness of the specimen.34 SiO2 is the main

300

constituent of sand and it has a negative charge because of dissociated silanol groups (–SiO−).

301

Most bacteria have negatively charged cell surfaces, therefore there is a repulsive force

302

between sand particles and bacterial cells. Positively charged poly-Lys could act as a binder

303

and attach bacterial cells to sand particles, which would promote efficient cementation. The

13 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 14 of 35

304

ionic strength of the solution and the salinity of the bacterial suspension also affect adsorption

305

of bacteria on sand particles. The collision efficiency increases with increasing ionic strength

306

of the solution, and adsorption of bacteria can be increased by increasing the salinity of the

307

bacterial suspension.34-36 The addition of poly-Lys helps to increase the ionic strength of the

308

solution and improves adsorption of bacteria on sand particles, therefore better cementation is

309

achieved.

310

And also as shown in the Figure 3 and Figure 6, ellipsoidal shaped crystals formed in the

311

presence of the poly-Lys could fill the pore spaces more efficiently and hence better

312

cementation could be achieved.

313

The SEM images in Figure 11 show that in the absence of poly-Lys, cementation

314

mainly occurs at the contact points between sand particles. This is the result of low

315

adsorption of bacteria on the sand surface. The carbonate crystals formed in the absence of

316

poly-Lys all have similar sizes and shapes, as shown in Figure 11(b). Figure 11(c) and (d)

317

show SEM images of sand specimens solidified in the presence of poly-Lys. The sand

318

particles are fully covered with carbonate and strong bonds are formed bridge between sand

319

particles. These SEM images indicate that poly-Lys acts as a binder and facilitates bacterial

320

cell adsorption on the sand particles. The irregular shapes and sizes of the crystals also assist

321

good cementation.

322

According to the experimental results, the addition of poly-Lys was found to improve

323

the efficiency of the MICP process. Therefore, naturally available cationic polypeptides/

324

polysaccharides such as lysozyme and chitosan can be used for real field applications to

325

improve the efficiency more sustainably in place of poly-Lys, supporting the concept of green

326

engineering.

327 328

14 ACS Paragon Plus Environment

Page 15 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

329 330 331 332 333 334 335 336

AUTHOR INFORMATION

337

Corresponding Author

338

Kazunori Nakashima*

339

*Phone: +81-11-706-6322. Fax: +81-11-706-6322.

340

E-mail: [email protected]

341

Notes

342

The authors declare no competing financial interest.

343 344

ACKNOWLEDGEMENTS

345

This work was partly supported by JSPS KAKENHI Grant Number JP15K18273 and

346

JP16H04404

347

15 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

348

Page 16 of 35

REFERENCES

349

(1) DeJong, J. T.; Fritzges, M. B.; Nusslein, K. Microbially induced cementation to

350

control sand response to undrained shear. Journal of Geotechnical and

351

Geoenvironmental

352

10.1061/(ASCE)1090-0241.

Engineering.

2006,

132

(11),

1381-1392;

DOI

353

(2) Choi, S. G.; Chu, J.; Brown, R. C.; Wang, K.; Wen, Z. Sustainable biocement

354

production via microbially induced calcium carbonate precipitation: use of lime stone

355

and acetic acid derived from pyrolysis of lignocellulosic biomass. Sustainable

356

Chemistry & Engineering. 2017, 5, 5183-5190; DOI 10.1021/acssuschemeng.7

357

b00521.

358

(3) Akiyama, M.; Kawasaki, S. Novel grout material comprised of calcium phosphate

359

compounds: In vitro evaluation of crystal precipitation and strength reinforcement.

360

Engineering Geology. 2012, 125, 119-128; DOI 10.1061/j.enggeo. 2011.11.011.

361

(4) Khan, Md. N. H.; Amarakoon, G. G. N. N.; Shimazaki, S.; Kawasaki, S. Coral sand

362

solidification test based on microbially induced carbonate precipitation using

363

ureolytic bacteria. Materials Transactions. 2015, 56 (10), 1725-1732; DOI

364

10.2320/matertrans.

365

(5) Achal, V.; et al. Production of bacteria for structural concrete, In Biotechnology and

366

Bio mimetic for Civil Engineers; Torgal, F. P., Labrincha, J. A., Diamanti, M. V., Yu,

367

C. P., Lee, H. K.,Eds.; Springer International Publishing: Switzerland 2015; pp.309.

368

(6) Fujita, M.; Nakashima, K.; Achal, V.; Kawasaki S. Whole-cell evaluation of urease

369

activity of pararhodobacter sp. isolated from peripheral beach rock. Biochemical

370

Engineering Journal. 2017, 124, 1-5; DOI 10.1016/j.bej.2017.04.004.

371

(7) Keykha, H. A.; Huat, B. B. K.; Asadi, A.; Kawasaki, S. Electro-biogrouting and its

372

challenges. International Journal of Electrochemical Science. 2012, 7, 1196-1204.

16 ACS Paragon Plus Environment

Page 17 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

373

(8) Mortensen, B. M.; Haber, M. J.; DeJong, J. T.; Caslake, L. F.; Nelson, D.C. Effects of

374

environmental factors on microbial induced calcium carbonate precipitation. Journal

375

of Applied Microbiology. 2011, 111, 338-349.

376 377

(9) Wfiffin, V. S. Microbial CaCO3 precipitation for the production of biocement. Ph.D.Dissertation, Murdoch University, Western Australia, 2004.

378

(10) Amarakoon, G. G. N. N.; Kawasaki, S. Factors affecting sand solidification using

379

MICP with pararhodobacter sp. Materials Transactions. 2017, 59 (1), 71-81; DOI

380

10.2320/matertrans.M-M2017849.

381

(11) Whiffin, V. S.; Van Paassen, L. A.; Harkes, M. P. Microbial carbonate precipitation

382

as a soil improvement technique. Geomicrobiology Journal. 2007, 24 (5), 417-423;

383

DOI /10.1080/01490450701436505.

384 385 386 387

(12) Polowczyk, I.; Bastrzyk, A.; Fiedot, M. Protein-mediated precipitation of calcium carbonate. Materials. 2016, 9 (11), 944:1-16; DOI 10.3390/ma9110944. (13) Mann, S. Biomineralization, Principles and Concepts in Bioinorganic Materials Chemistry; Oxford University Press: Oxford,U.K.,2001.

388

(14) Sondi, I.; Matijevic, E. Homogeneous precipitation of calcium carbonates by enzyme

389

catalyzed reaction. Journal of Colloid and Interface Science. 2001, 238 (1), 208-214;

390

DOI 10.1006/jcis.2001.7516

391

(15) Yao, Y.; Dong, W.; Zhu, S.; Yu, X.;

Yan, D. Novel morphology of calcium

392

carbonate controlled by poly(l-lysine). Lamgmuir. 2009, 25 (22), 13238–13243; DOI

393

10.1021/la901913d.

394 395

(16) Kato, T. Polymer/calcium carbonate layered thin-film composites. Advanced materials. 2000, 12,1543-1546.

396

(17) Falini, G.; Fermani, S.; Gazzanoa, M.; Ripamontia, A. Polymorphism and

397

architectural crystal assembly of calcium carbonate in biologically inspired polymeric

17 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 18 of 35

398

matrices. Journal of the Chemical Society, Dalton Transactions. 2000, (21), 3983-

399

3987; DOI 10.1039/B003334K.

400 401

(18) Addadi, L.; Weiner, S. Control and design principles in biological mineralization. Angew.Chem.Ent.Ed. 1992, 31,153-169.

402

(19) Tong, H.; Ma, W.; Wang, L.; Wan, P.; Hu, J.; Cao, L. Control over the crystal phase,

403

shape, size and aggregation of calcium carbonate via a l-aspartic acid inducing

404

process.

405

10.1016/j.biomaterials.2003.10.038.

Biomaterials.

2004,

25

(17),

3923-3929;

DOI

406

(20) Dzakula, B. N.; Brecevic, L.; Falini, G.; Kralj, D. Calcite crystal growth kinetics in

407

the presence of charged synthetic polypeptide. Journal of Crystal Growth and Design.

408

2009, 9 (5), 2425-2434; DOI 10.1021/cg801338b.

409

(21) Xie, A. J.; Shen, Y. H.; Zhang, C. Y.; Yuan, Z. W.; Zhu, X. M.; Yang, Y. M. Crystal

410

growth of calcium carbonate with various morphologies in different amino acid

411

systems.

412

10.1016/j.jcrysgro.2005.08.039.

Journal

of

crystal

growth.

2005,

285

(3),

436-443;

DOI

413

(22) Addadi, L.; Moradian, J.; Shayt, E.; Maroudast, N. G.; Weinert, S. A chemical model

414

for the cooperation of sulfates and carboxylates in calcite crystal nucleation:

415

Relevance to biomineralization. Proc. Nail. Acad. Sci. USA.1987, 84 (9), 2732-2736.

416

(23) Lauchnor, E. G.; Topp, D. M.; Parker, A. E.; Gerlach, R. Whole cell kinetics of

417

ureolysis by Sporosarcina pasteurii. Journal of Applied Microbiology. 2015, 118,

418

1321–1332; DOI 10.1111/jam.12804.

419

(24) Danjo, T.; Kawasaki, S.

Microbially induced sand cementation method using

420

Pararhodobacter sp. strain SO1, inspired by beach rock formation mechanism.

421

Material Transaction. 2016, 57, 428–437; DOI 10.2320/matertrans.M-M2015842.

18 ACS Paragon Plus Environment

Page 19 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

422

(25) Danjo, T.; Kawasaki, S. A study of the formation mechanism of beach rock in

423

okinawa, japan: toward making artificial rock. International Journal of Geomate.

424

2013, 5 (1), 634–639.

425 426 427

(26) Mitsuyama, S.; Nakashima, K.; Kawasaki, S. Evaluation of porosity in biogrouted sand using microfocus X-ray CT. International Journal of Geomate. 2017, 12, 71-76. (27) Ahmed Al Qabany, A. A.; Soga, K.; Santamarina, C. Factors affecting efficiency of

428

microbially

induced

calcite

precipitation.

429

Geoenvironmental

430

10.1061/(ASCE)GT.1943-5606.0000666.

Engineering.

2012,

Journal 138

of (8),

Geotechnical

and

992-1001;

DOI

431

(28) Dzakula, B. N.; Falini, G.; Brecevic, L.; Skoko, Z.; Kralj, D. Effects of Initial

432

Supersaturation on Spontaneous Precipitation of Calcium Carbonate in the Presence

433

of Charged Poly-L-Amino Acids. Journal of Colloidal and Interface Science. 2009,

434

343(2), 553-563; DOI 10.1016/j.jcis.2009.12.010.

435

(29) Fischer, S. S.; Galinat, J. K.; Bang, S. S. Microbiological precipitation of CaCO3. Soil

436

Biology and Biochemistry. 1999, 31 (11), 1563-1571; DOI 10.1016/S0038-

437

0717(99)00082-6.

438

(30) Shibata, A.; Yamamoto, M.; Yamashita, T.; Chiou, J. S.; Kamaya, H.; Ueda, I.

439

Biphasic effects of alcohols on the phase transition of poly(L-lysine) between α–helix

440

and β sheet conformations. Biochemistry. 1992, 31, 5728-5733.

441

(31) DeJong, J. T.; Mortensen, B. M.; Martinez, B. C.; Nelson, D. C. Bio-mediated soil

442

improvement.

443

10.1016/j.ecoleng.2008.12.029.

444 445

Ecological

Engineering,

2010,

36,

197-210;

DOI

(32) Shafii, R. N.; Clough, W. The Influence of Cementation on the Static and Dynamic Behavior of Sands. Stanford University, California.,1982.

19 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

446 447

Page 20 of 35

(33) Paassen, L.V. Biogrout: Ground Improvement by Microbially Induced Carbonate Precipitation. Ph.D. Dissertation, Delft University of Technology, Netherlands, 2009.

448

(34) Harkes, M. P.; Paassen, L. A. V.; Booster, J. L.; Whiffin, V. S.; Loosdrechta, M. C.

449

M. V. Fixation and distribution of bacterial activity in sand to induce carbonate

450

precipitation for ground reinforcement. Ecological Engineering. 2010, 36 (2), 112-

451

117; DOI 10.1016/j.ecoleng.2009.01.004.

452

(35) Foppen, J. W. A.; Schijven, J. F. Evaluation of data from the literature on the

453

transport and survival of Escherichia coli and thermotolerant coliforms in aquifers

454

under saturated conditions. Water Research. 2006, 40 (3), 401–426; DOI

455

10.1016/j.watres.2005.11.018.

456

(36) Foppen, J. W. A.; Schijven, J. F. Transport of E.-coli in columns of geochemically

457

heterogeneous sediment. Water Research. 2005, 39 (13), 3082–3088; DOI

458

10.1016/j.watres.2005.05.023.

20 ACS Paragon Plus Environment

Page 21 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

459

ACS Sustainable Chemistry & Engineering

Figure captions

460 461

Figure 1. Amounts of precipitate formed at various bacterial concentrations (OD600) with or

462

without addition of poly-Lys. Error bars show the standard deviation of the values in three

463

independent experiments.

464

465

Figure 2. SEM images of CaCO3 precipitates at various bacterial concentrations without

466

poly-Lys: (a) OD600 = 0.01, (b) OD600 = 0.05, (c) OD600 = 0.1, and (d) OD600 = 0.2.

467 468

Figure 3. SEM images of CaCO3 precipitates at various bacterial concentrations with poly-

469

Lys (10 mg/L): (a) OD600 = 0.01, (b) OD600 = 0.05, (c) OD600 = 0.1, and (d) OD600 = 0.2.

470 471

Figure 4. XRD patterns of CaCO3 precipitates (a) without poly-Lys and (b) with poly-Lys.

472 473

Figure 5. Variations in amount of carbonate precipitated with changes in poly-Lys

474

concentration. Error bars show the standard deviation of the values in three independent

475

experiments.

476 477

Figure 6. SEM images of CaCO3 precipitated by bacteria (OD600 = 0.1) at different poly-Lys

478

concentrations: (a) 1 mg/L, (b) 10 mg/L, (c) 30 mg/L, and (d) 50 mg/L.

479 480

Figure 7. Formation of twin-sphere crystals in presence of poly-Lys.

21 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 22 of 35

481 482

Figure 8. Time courses of (a) Ca2+ concentration and (b) pH of effluent in sand solidification

483

tests.

484 485

Figure 9. Solidified sand specimens after 14 days (a) before UCS measurements and (b) after

486

UCS measurements.

487 488

Figure 10. Estimated UCS values of solidified sand specimens. Error bars show the standard

489

deviation of the values in three independent experiments.

490 491

Figure 11. SEM images of cemented sand samples: without poly-Lys (a,b) and with poly-Lys

492

(c,d).

493

22 ACS Paragon Plus Environment

Page 23 of 35

494 0.3

495

0.25

496 497 498 499

Precipitate (g)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

0.2 0.15 Without poly-Lys

0.1 0.05

With poly-Lys

0

500

0

0.05 0.1 0.15 0.2 0.25 Bacteria Concentration (OD600)

501 502

Figure 1. Amounts of precipitate formed at various bacterial concentrations (OD600)

503

with or without addition of poly-Lys. Error bars show the standard deviation of the

504

values in three independent experiments.

23 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

(b) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 24 of 35

505 506

(a)

(b)

507 508 509 510 511 100 µm

100 µm

512 513

(d)

(c)

514 515 516 517 518 519

100 µm

100 µm

520 521 522

Figure 2. SEM images of CaCO3 precipitates at various bacterial concentrations without poly-Lys: (a) OD600 = 0.01, (b) OD600 = 0.05, (c) OD600 = 0.1, and (d) OD600

523

= 0.2.

24 ACS Paragon Plus Environment

Page 25 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

524 525

(b)

(a)

526 527 528 529 530 531

100 µm

100 µm

532 (c)

(d)

533 534 535 536 537 538

100 µm

100 µm

539 540 541

Figure 3. SEM images of CaCO3 precipitates at various bacterial concentrations with poly-Lys (10 mg/L): (a) OD600 = 0.01, (b) OD600 = 0.05, (c) OD600 = 0.1, and (d) OD600 =

542

0.2.

25 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

543 544

(a) 120000

545

C

100000

546

80000

Intensity

547 548

60000 40000

549 20000

550

C

C

C C

C

C

C

0 10

551

20

30

40 50 2Ɵ (Deg)

552

60

70

80

70

80

553 (b)

554

100000 C

80000

555 Intensity

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 26 of 35

556 557

60000 40000

558 20000

559 10

561

563

C C

C C

0

560

562

C

C

20

30

40 50 2Ɵ (Deg)

60

C

Figure 4. XRD patterns of CaCO3 precipitates (a) without poly-Lys and (b) with polyLys.

564

26 ACS Paragon Plus Environment

Page 27 of 35

565 566 0.3

567

0.25

568 569 570

Precipitate (g)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

0.2 0.15 0.1

571

0.05

572

0 0

5

573

10 15 20 25 30 35 40 45 50 55 Poly-Lys concentration (mg/L)

574 575

Figure 5. Variations in amount of carbonate precipitated with changes in poly-Lys

576

concentration. Error bars show the standard deviation of the values in three

577

independent experiments.

27 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

578

(a) (a)

Page 28 of 35

(b)

579 580 581 582 583

100 µm

100 µm

584

(c)

(d)

585 586 587 588 589 590

100 µm

100 µm

591

Figure 6. SEM images of CaCO3 precipitated by bacteria (OD600 = 0.1) at different 592

poly-Lys concentrations: (a) 1 mg/L, (b) 10 mg/L, (c) 30 mg/L, and (d) 50 mg/L. 593 594

28 ACS Paragon Plus Environment

Page 29 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

595 596 597 598 599 600 601 602 603 604 605 606

(c)

607 608 609

Figure 7. Formation of twin-sphere crystals in presence of poly-Lys.

610

29 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

611

18000

(a)

16000

Ca2+ Concentration (ppm)

612 613 614 615 616 617

14000 Inlet

12000 10000

S1

8000

S2

6000

S3

4000

S4

2000 0

618

0

2

4

619

6 8 10 Time (Days)

12

14

16

620 621

8.5

(b)

622

8

623 624

7.5

S1

pH

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 30 of 35

S2

7

625

S3

626

6.5

627

6

S4

0

628

2

4

6

8

10

12

14

16

Time (Days)

629 630

Figure 8. Time courses of (a) Ca2+ concentration and (b) pH of effluent in sand

631

solidification tests. (Arrows indicate the time of bacteria reinjection to the sand

632

specimens.)

633

30 ACS Paragon Plus Environment

Page 31 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649

Figure 9. Solidified sand specimens after 14 days (a) before UCS measurements 650 651

and (b) after UCS measurements.

652

31 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

653 6

654

Bacteria injection once

Bacteria injection twice

655 5

656 657 658 659 660 661

Estimated UCS (MPa)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 32 of 35

4

3

2

662 663

1

664 665 666 667

0 Bot

Mid S1

Top

Bot

Mid

Top

Bot

S2

Mid S3

Top

Bot

Mid

Top

S4

668 669 670

Figure 10. Estimated UCS values of solidified sand specimens. Error bars show the standard deviation of the values in three independent experiments.

671 672

S1 and S3 (open): without addition of poly-Lys,

673

S2 and S4 (closed): with addition of poly-Lys 674

32 ACS Paragon Plus Environment

Page 33 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

675 676

(a)

(b)

677 678 679 680 681 100 µm

682 683

(c)

100 µm

(d)

684 685 686 687 688 100 µm

689

100 µm

690 691

Figure 11. SEM images of cemented sand samples: without poly-Lys (a,b) and with

692

poly-Lys (c,d). 693 694

33 ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 34 of 35

Table 1. Experimental conditions for sand solidification

695 696

poly-Lys

bacteria injection

S1

-

once b

699

S2

100 mg/L a

once b

700

S3

-

twice c

S4

100 mg/L a

twice c

697 698

701 702 703

a

Initial concentration of the poly-Lys solution applied to the column in solidification test.

704

b

Injection of bacteria culture only at the beginning of solidification test.

705

c

Injection of bacteria culture at the beginning and after 7 days of solidification test.

706

34 ACS Paragon Plus Environment

Page 35 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

707

ACS Sustainable Chemistry & Engineering

For Table of Contents Use Only

708 709 710 711 712 713 714 715 716

Synopsis

717

Addition of poly-lysine is more sustainable way to improve the efficiency of bio-cementation

718

by bacteria.

35 ACS Paragon Plus Environment