Evaluation of Pyridaben Residues on Fruit Surfaces and Their Stability

Oct 10, 2017 - The data show that the maximum amounts of the residue on fruit surfaces after soaking in water (50 mg L–1, 5 min) are 0.583 mg kg–1...
1 downloads 9 Views 2MB Size
Subscriber access provided by Southern Cross University Library

Article

Evaluation of Pyridaben Residues on Fruits Surface and its Stability by A Novel On-line Dual-frequency Ultrasonic Device and Chemiluminescence Detection Wangbing Zhang, Mei Wei, Wei Song, Yi-Xuan Gong, and Xin-An Yang J. Agric. Food Chem., Just Accepted Manuscript • DOI: 10.1021/acs.jafc.7b03357 • Publication Date (Web): 10 Oct 2017 Downloaded from http://pubs.acs.org on October 18, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Journal of Agricultural and Food Chemistry is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 30

Journal of Agricultural and Food Chemistry

1

Evaluation of Pyridaben Residues on Fruits Surface and

2

its Stability by A Novel On-line Dual-frequency

3

Ultrasonic Device and Chemiluminescence Detection Wang-Bing Zhang a*, Mei Wei a, Wei Song b, Yi-Xuan Gong a and Xin-An Yang a*

4 5

a

Department of Applied Chemistry, Anhui University of Technology, Maanshan, Anhui 243002, P. R.

6 7

China b

Anhui Entry Exit Inspection and Quarantine Bureau, Hefei, Anhui 230022, P. R. China

8

ABSTRACT: In this paper, we firstly report the development of a highly sensitive and economical

9

method for accurate analysis of pyridaben residues on fruits based on dual-frequency ultrasonic

10

treatment (DFUT) and flow injection chemiluminescence (CL) detection. The DFUT device is

11

constituted

12

with different structures have been designed and applied to evaluate the function of DFUT in the

13

detection process. Recorded data showed that DFUT is an effective method for improving the pyridaben

14

CL signal. The signal of pyridaben in response to DFUT is 2.0- 3.3 times stronger than the response to

15

only ultrasonic probe at 20kHz or ultrasonic bath at 40kHz, respectively. In addition, the response

16

obtained from the concentric circles QGC is 2.1 times stronger than the response to the spiral tube QGC.

17

Under the optimized condition, the proposed method has advantages, such as wide linear range

18

(0.8-100.0 µg L-1), high sensitivity (limit of detection is 0.085 µg L-1) and good stability (RSDs ≤ 4.7%

19

in the linear range) for pyridaben determination. We apply this method to monitor the residue pyridaben

20

on some fruits. The data shows that the maximum amounts of residue on fruits surface after soaking in

21

water (50 mg L-1, 5 min) are 0.583 mg kg-1 (apple), 0.794 mg kg-1 (orange) and 0.351 mg kg-1 (pear).

by integrating an ultrasonic bath with an ultrasonic probe. Two quartz glass coils (QGC)

1 Environment ACS Paragon Plus

Journal of Agricultural and Food Chemistry

Page 2 of 30

22

However, the concentration of pyridaben in presence of sunlight decreases rapidly, showing its poor

23

light stability.

24

Keyword: Dual-frequency ultrasonic irradiation; on-line CL determination; Pyridaben; Stability;

25

Residue on fruits surface

26

INTRODUCTION

27

As

28

4-chloropyridazin-3(2H)-one (Figure S1, Supporting Information), is widely used for controlling

29

mites in fruit, tobacco, vegetable and other crops 1. Despite its low toxicity, overuse still can cause

30

harm to humans through food chain. For instance, Boyd et al. have reported that pyridaben can

31

affect the activity of mitochondrial complex I in the electron transport chain 2. Therefore, the

32

maximum residue limits of pyridaben in some countries have been established, such as 0.5 mg kg-1

33

in Spain (peppers, 7 day pre-harvest interval) 3, and 5 mg kg-1 in China (tea) 4.

one

of

the

nonsystemic

acaricide,

Pyridaben,

2-tert-butyl-5-(4-tert-butylbenzylehio)-

34

Generally, chromatography with mass spectrometry or other selective and sensitive detectors is a

35

standard method for the determination of pyridaben. For example, Yang et al. reported a magnetic

36

mixed hemimicelles dispersive solid-phase extraction (MMHDSPE) with high performance liquid

37

chromatography (HPLC)-diode array method for determination of pyridaben in fruit juice 5. Sun et al.

38

developed a selective method for determination of pyridaben in citrus fruits by ultra-performance liquid

39

chromatography coupled with tandem mass spectrometry (UPLC–MS/MS), which limit of detection is l

40

µg kg-1 6. Douglas et al. established a sensitive procedure based on gas

41

triple-Quadrupole MS for pyridaben determination in several teas 7. Xiong et al. analyzed pyridaben in

42

water and beverage samples by GC coupled with a flame photometric detector within a range of 8.0-600

43

µg L-1 8. Zhang et al. developed a protocol for the collection of LC electrospray ionization quadruple

44

linear ion trap MS for identification of pyridaben in peach 9. Frenich et al. proposed a method, in which

45

pressurized liquid extraction coupled with GS-MS/MS is used for identification of pyridaben in food

46

commodities with limit of quantitation of 0.01 mg kg-1

10

chromatography

(GC)

. Liu et al. presented a quantification method

2 Environment ACS Paragon Plus

Page 3 of 30

Journal of Agricultural and Food Chemistry 11

47

based on HPLC-tandem MS for studying the dissipation of pyridaben in cabbage

. Many of these

48

above methods have excellent separation performance, which can analyze a large number of pesticide

49

residues in complex samples at the same time. However,

50

such separation and quantitative analysis,

comprehensive instruments are required in

thus high costs and other issues are particularly inevitable.

51

Because of its easy operation, low cost and high sensitivity, chemiluminescence (CL) technique have

52

been more and more used for pesticide residue detection in recent years. The analytes of this method

53

including organophosphorus, organochlorines, and carbamate pesticide, and the limit of determination

54

for each compound is lower than 0.01 mg L-1

55

picoxystrobin, azoxystrobin, and fenpyroximate) determination, our studies indicate that direct detecting

56

by CL method is impossible, because these residues have no apparent effect on the traditional oxidant

57

luminol CL systems (including luminol-H2O2, luminol-KMnO4, and luminol-K2S2O8, etc.). Subsequent

58

experiments show that the CL intensity of these residues in luminol-oxidant system could be promoted

59

in varying degrees after 10-30 min off-line ultrasonic bath treatment. And this enhancement is linearly

60

related to the concentration of residues. The sensitivity and precision of the proposed method in our

61

early works were superior or at least at the same level as those reported methods such as HPLC-MS and

62

GC-MS

63

detection of pesticide residues is promising.

17-19

12-16

. For acaricide and fungicide residues (such as

, which indicated that the application prospect of ultrasonic assisted CL technology in the

64

Compared with the previous work, the novelty of this study is to design a new dual-frequency

65

ultrasonic (DFUT) device, and build an on-line detection system with chemiluminescence detector, then

66

solve the problems, such as loss of analyte, pollution and time-consuming during the off-line ultrasonic

67

processing. Specifically, the ultrasonic device incorporating ultrasonic bath and ultrasonic probe, on one

68

hand, does not contact the sample solution directly during the process of ultrasonic irradiation, thus

69

avoiding potential pollution problems. On the other hand, on-line processing and detection technology

70

not only provides more rapid and real-time data acquisition, but also avoids the loss of the analyte. Also,

71

the high ultrasonic densities of ultrasonic probe

20

coupled with the temperature control function of

3 Environment ACS Paragon Plus

Journal of Agricultural and Food Chemistry 21

Page 4 of 30

72

ultrasonic bath

may have higher efficiency for enhancing the response of chemiluminescence signal.

73

The proposed on-line DFUT assisted CL method is used to evaluate pyridaben residues on fruits surface

74

and its stability in sunlight. Its accuracy is confirmed by recovery experiments and HPLC-MS. As far as

75

we know, no other study about the application of CL in the pyridaben monitoring had been reported.

76 77

Figure 1. Design of dual-frequency ultrasonic extraction scheme (a), a photo of QGC (b), and

78

scheme of the FIA-CL system (c). QGC quartz glass coil; UBG ultrasonic bath generator; UPG

79

ultrasonic probe generator; S sample; C acetonitrile solution (0.1% v/v); P1 P2 pump; V eight-port

80

value; RC reaction cell; W waste; HV high voltage; PMT photomultiplier tube.

81

EXPERIMENTAL PROCEDURES

82

Apparatus and Materials. A homemade ultrasonic device (Figure 1A) is used to evaluate the

83

efficiency of ultrasonic treatment. The device consists of an ultrasonic bath instrument

84

(240mm×140mm×100mm) and an ultrasonic probe generator (20 kHz, Shanghai Guante Ultrasonic

85

Instrument Co., Shanghai, China). Two quartz glass coils (QGC, 2mm i.d., 300mm length, ~ 920µL,

86

Figure 1B) with different structures fixed on iron support as the reaction tubes are tested. Both ends

87

of the QGC are made into elongated shape, to be easily connected to emulsion tube. The distance

88

between QGC and the bottom of ultrasonic instrument (H1, cm) can be adjusted by changing the iron

89

support height. The ultrasonic probe (8mm diameter, 150mm length) is positioned at a certain 4 Environment ACS Paragon Plus

Page 5 of 30

Journal of Agricultural and Food Chemistry

90

distance (H2, cm) above the QGC. The ultrasonic frequency of ultrasonic bath can be switched in

91

three modes, 40, 50, 59 kHz. Besides, the temperature of water bath can be controlled by adjusting

92

the flow rate of homemade external circulating water. Information about the CL detector, chemical

93

reagents and sources used in the experiment are listed in Supporting Information.

94

Sample Preparation. Fruit samples (apples, oranges, and pears) used in the experiment were

95

purchased from local market. Before preparation, these samples are washed with double deionized

96

water (DDW) and then air dried at 20oC. According to the literature

97

follows. Firstly, nine samples including three apples (202.5g, 164.8g and 175.6g), three oranges

98

(124.7g, 133.2g and 102.8g) and three pears (284.7g, 353.8g and 332.7g) are respectively dipped

99

into beakers containing solution A (50.0 mg L-1 pyridaben, 300 mL) for 5 min and then the samples

100

are taken out and air dried. Secondly, the dried samples are dipped into solution B (DDW, 300 mL)

101

for 10 min and then the samples are taken out and air dried again. Thirdly, the dried samples are

102

dipped into solution C (DDW, 200 mL) for 10 min.

13

, the samples are prepared as

103

In order to know the change of pyridaben concentration in the above eluted solutions, 2.50 mL

104

solution B and 10.00 mL C are quantitatively transferred into a 25mL colorimeter tube, respectively.

105

And 2.50 mL acetonitrile-water solution (1% v/v) is added then dilute it to volume with DDW for

106

CL determination.

107

Analytical Procedures. The on-line DFUT and flow injection CL determination of samples are

108

described in Figure 1C. Two peristaltic pumps named P1 and P2 are used to transport luminol and

109

KMnO4 (P1), NaOH and pyridaben/carrier [acetonitrile-water (0.1% v/v)] solutions (P2) at the

110

selected flow rate, respectively. Follow the experimental procedures listed in Table 1, the sample

111

solution is firstly pumped from the colorimeter tubes to storage coil by P2 at a flow rate of 4.0 mL

112

min-1. Next, the sample solution is driven into the QGC by the carrier at the same flow rate, where

113

the sample is irradiated by selected ultrasonic conditions. The above solutions are mixed and reacted

114

with luminol and KMnO4 in the reaction cell lastly, and the optical signal is recorded with the 5 Environment ACS Paragon Plus

Journal of Agricultural and Food Chemistry

Page 6 of 30

115

photomultiplier tube and the luminometer. Quantitative analysis is achieved by comparing the

116

changes before and after the implementation of pyridaben. The calculation formula is ∆I=I-I0. I is

117

the signal of pyridaben-luminol-KMnO4 system, and I0 is obtained under the same condition with

118

acetonitrile-water (0.1% v/v) solution instead of pyridaben. Instrument settings and operational

119

parameters of the experimental DFUT-CL system are summarized in Table S1 (Supporting

120

Information).

121

Table 1. Working program of the on-line ultrasonic treatment coupled with CL determination Flow rate/ mL min-1 Step

Time/s

Events

P1

P2

1

2.8

4.0

20

Draw sample solution through sampling tube

2

0.0

0.0

5

Move sampling tube into acetonitrile solution

3

2.8

4.0

20

Sample is carried into the QGC with acetonitrile solution

4

0.0

0.0

480 Sample is irradiated by ultrasound in the QGC

5

2.8

4.0

40

Reacting with luminol and KMnO4 , then record the CL signal

6

0.0

0.0

5

Return to step 1

122

HPLC equipped with a ZORBAX XDB-C18 analytic column (2.1×150mm) and an MS detector

123

(Agilent series 6430, USA), is used for recovery test to validate the accuracy and feasibility of the

124

proposed method. Instrument settings and operational parameters used for the HPLC-MS system are

125

summarized in Table S2 (Supporting Information).

126

RESULTS AND DISCUSSION

127

DFUT-CL Determination of Pyridaben. In general, the quantitative basis of the CL method is that

128

the analyte improves or inhibits the optical signal of different luminescence system 6 Environment ACS Paragon Plus

11-13

. However,

Page 7 of 30

Journal of Agricultural and Food Chemistry

129

preliminary experimental data shows that the addition of pyridaben doesn't change the CL signals of

130

luminol with H2O2, KMnO4 or K2S2O8. When the on-line DFUT procedure is carried out before the

131

pyridaben mixing with oxidant and luminol, fortunately, the CL signal of the luminol-oxidant

132

system is markedly enhanced. Figure 2 shows the effect of different concentration of pyridaben on

133

the CL signal in the luminol-KMnO4 system after DFUT. A good linear relationship (R2=0.9985)

134

between the relative CL signal (∆I) and pyridaben concentration (inset of Figure 2) range from 0.8

135

to 100.0 µg L-1 displays the wide linear range of the proposed methods in the field of monitoring

136

pyridaben.

137 138

Figure 2. CL intensities of different concentration of pyridaben after on-line DFUT (For the

139

convenience of description, the time required for ultrasonic treatment in each measurement process

140

is subtracted). Conditions of DFUT: 20kHz ultrasonic probe + 59kHz ultrasonic bath (frequency),

141

20W + 80 W (power), 50oC (temperature), 6min (time).

142

The mechanism of the enhancing effect on the CL signal is considered as a kind of energy transfer

143

process based on the following experimental facts: i) there is no difference in HPLC-MS

144

chromagraphy between before and after ultrasonic treatment (Figure S2, Supporting Information),

145

which indicates that ultrasound does not promote degradation of pyridaben. ii) Except for peak

146

intensity change,there is no new peak is found in the fluorescence and UV spectra of the 7 Environment ACS Paragon Plus

Journal of Agricultural and Food Chemistry

Page 8 of 30

147

luminol-KMnO4-pyridaben with/without DFUT (Figure S3, Supporting Information), which confirm

148

that the emission spectrum belongs to 3-aminophthalate ion (3-AP). iii) the enhancement of CL

149

signal is linearly related to the concentration of pyridaben, showing that pyridaben is involved in the

150

luminescence process, not just because of hydroxyl radical produced in ultrasound.

151 152 153

Figure 3. Diagram of the mechanism. We present the reaction process depicted in Figure 3. Briefly, under the irradiation of ultrasound, 22, 23

154

water molecules produce hydroxyl radical (·OH) with high activity

155

pyridaben gaining higher energy (excited). When the excited state of aminophthalate (3-AP*,

156

produced by reaction between luminol and KMnO4) releases energy from the excited state back to

157

the ground state, it can obtain energy from excited pyridaben molecules and re-excited to 3-AP*.

158

Obviously, CL intensity is enhanced in the above process 24. More detailed explanations are listed in

159

the Supporting Information.

160

Optimum of Ultrasonic Conditions. Effect of ultrasonic mode on the signal of pyridaben. Based on

161

the frequency and number of ultrasonic waves applied, we tested the effect of pyridaben on the CL

162

signals of the luminol-KMnO4 system in seven ultrasonic modes after 10 min irradiation. The results

163

are shown in Figure 4, the highest CL signal is obtained in the 20kHz ultrasonic probe + 59kHz 8 Environment ACS Paragon Plus

, then these radicals cause

Page 9 of 30

Journal of Agricultural and Food Chemistry

164

ultrasonic bath mode. Compared with this mode, the CL signals of pyridaben irradiated by 20kHz

165

ultrasonic probe and 59kHz ultrasonic bath separately are about 50% and 30%, respectively.

166 167

Figure 4. Effect of ultrasonic mode on the CL intensities. Conditions of ultrasonic treatment are listed in

168

Table 1. UB ultrasonic bath; UP ultrasonic probe.

169

Gogate pointed out that the cavitation bubbles produced by high frequency ultrasonic wave can be 25

170

used as the nuclei of lower frequency cavitation

171

dual-frequency ultrasound is quite different from that of single frequency 26, 27. And these cavitation

172

bubbles lead to more homogeneous and intense cavitation effect as compared to a single frequency

173

sounding

174

formation of hydroxyl radicals (·OH). Besides, an interesting experimental phenomenon either

175

dual-frequency mode or single-frequency mode is found, that the increase of the CL signal is related

176

to the applied ultrasonic frequency. The CL signals of pyridaben in Figure 4 are increased about

177

30% (dual-frequency mode) and 22% (single-frequency mode) with the UB frequency from 40kHz

178

to 59kHz. As we know, the cavitation effect is related to the size of the resonant bubble radius (r)

179

and bubble collapse time (τ). Although small bubbles produce weak cavitation 30, a decrease of more

28, 29

. Therefore, the size of cavitation bubbles in

. This high intensity cavitation effect under dual-frequency mode promotes the

9 Environment ACS Paragon Plus

Journal of Agricultural and Food Chemistry

Page 10 of 30

180

than 40% in collapse time (Table S3, Supporting Information) give rise to more acoustic cycles and

181

results in the formation of large amounts of smaller sizes cavitations bubbles at higher frequencies,

182

and thus more cavitations per unit time

183

production, thus promote pyridaben to form excited products.

184

Effect of QGC shape and position.Two shapes of QGC are applied to the ultrasonic irradiation of

185

pyridaben (Figure 1B). One of the QGC is concentric circles shape, and the other one is a spiral

186

tube. The position of QGC in the ultrasonic device is also important in the process of ultrasonic

187

irradiation

188

considered together in this paper.

32

31

. Obviously, these factors are beneficial to radical

. Therefore, the effects of QGC shape and position on the signal intensity of CL are

189

Figure 5 displays the signal change tendency after changing the position of QGC in the device. This

190

experiment is carried out by fixing one of distance (H1 or H2) at 1.0 cm. Figure 5A indicates that the CL

191

signal intensity decreases remarkably both with the distance of H1 and H2 from 0.5 to 4.0cm for 20 µg

192

L-1 pyridaben solution when the threaded tubes QGC is used. Figure 5B indicates that the CL signal

193

intensity increases both with the distance of H1 and H2 from 0.5 to 1.0cm, and then rapidly decreases

194

when the concentric circle QGC is used. Compared with the distance between QGC and bottom of

195

ultrasonic bath (H1), the change of ultrasonic probe position (H2) caused more severe signal changes,

196

which indicated that the distance has more influence on ultrasonic probe.

197

Figure 5 also shows that the shape of QGC is an important factor that impacts signal intensity. Under

198

the same conditions, the response obtained from the concentric circles QGC is 2.1 time of that from the

199

spiral tube QGC. The reason may be that the size (2.0 cm) of the spiral tube caused the solution in the

200

tube to be farther away from the probe than the solution in the concentric circles QGC. Therefore, the

201

concentric circles QGC placed at the middle of the two ultrasonic devices (H1= H2 = 1.0 cm) is used as

202

the optimum conditions in the sample analysis process with the best stability. Meanwhile, RSDs of 11

203

times measurements are less than 4.7% within linear range (e.g. 1.3% for 20µg L-1 and 2.5% for 50µg

204

L-1, Figure S4, Supporting Information). Also, good stability of the proposed methods is documented. 10 Environment ACS Paragon Plus

Page 11 of 30

Journal of Agricultural and Food Chemistry

205 206

Figure 5. Effect of QGC shape and position on the CL intensity of 20 µg L-1 pyridaben. (a) for spiral

207

tube shape, and (b) for concentric circles shape. H1 (H2) is optimized by fixing the distance of H2 (H1) at

208

1cm.

209 210

Figure 6. Effect of time on the CL intensities. Conditions of ultrasonic treatment were listed in Table S1.

211

UB ultrasonic bath ; UP ultrasonic probe.

212

Effect of Ultrasonic Time. Figure 6 lists the change of the CL signal of pyridaben-luminol-KMnO4

213

with different ultrasonic time. The relative signal of the luminol-KMnO4 system increases with the

214

increased residence time for pyridaben sample solution stay in the QGC, and reaches the maximum 11 Environment ACS Paragon Plus

Journal of Agricultural and Food Chemistry

Page 12 of 30

215

signal at 8min (20kHz UP + 59kHz UB), 22min (20kHz UP) and 40min (59kHz UB), respectively.

216

Then the signal decreases with the prolonging of time. In addition, the maximum CL signals

217

obtained under the three modes are also different. As can be seen in Figure 6, the relative CL signals

218

of the pyridaben-luminol-KMnO4 system are only 73% (20kHz UP) and 61% (59kHz UB) of that

219

irradiated by dual-frequency mode with the same concentration.

220

Moreover, in a dual-frequency ultrasonic mode, the higher ultrasonic frequency, the shorter the

221

time required to reach maximum signal. For instance, when the 20kHz UP + 59kHz UB

222

dual-frequency mode is applied, it’s need 8 min to reach the maximum. When the 20kHz UP +

223

40kHz UB mode is used, the time is increased to 12 min (data not shown here). Meanwhile, the

224

signals of pyridaben are decreased after ultrasonic treatment for a long time. It’s shows that

225

prolonging the ultrasonic time does not yield stronger signal. It should be noted that the appropriate

226

response signal can also be obtained by shortening the ultrasonic processing time to 3-4min.

227

Effect of Ultrasonic Power and Temperature. The effect of ultrasonic power on the CL signal in the

228

pyridaben-luminol-KMnO4 system is studied by fixed the ultrasonic probe power at 80 W. Figure

229

S5A-C (Supporting Information) shows the changes in the relative CL signals of the

230

pyridaben-luminol-KMnO4 system produced by varying the power of the ultrasonic bath under different

231

dual-frequency modes. Due to violent cavitation at high ultrasonic power, the acoustic reaction of H2O

232

is accelerated 32, resulting in linear enhancement of the relative CL signal of pyridaben-luminol-KMnO4

233

with ultrasonic power (Figure S5D, Supporting Information). As a result, 200W (the maximum power

234

of the ultrasonic bath) is selected.

235

The influence of bath temperature is investigated by the temperature control function of ultrasonic

236

bath. The results are shown in Figure S6 (Supporting Information). When the temperature reaches 50oC,

237

the DUFT-CL signal of pyridaben is the highest. The influence of temperature on the CL signal is

238

basically independent of the applied ultrasonic frequency (Figure S6D, Supporting Information).

239

Although more cavitation bubbles formed in high temperatures

30-32

12 Environment ACS Paragon Plus

, the effect of bubble rupture is

Page 13 of 30

Journal of Agricultural and Food Chemistry

240

weakened when the temperature is too high (e.g. up to 70 oC in our experiment). Therefore, 50 oC is a

241

better temperature.

242

Optimization of CL Conditions. In general, the higher luminol concentration, the larger CL signal will

243

be obtained

244

intensity increases with the increase of the luminol concentration in the range of 1.0×10-5mol L-1 to

245

1.0×10-4 mol L-1. As the concentration exceeds 7.0×10-5 mol L-1, the upward tendency of the signal

246

becomes slighter. These data can be found in Figure S7A (Supporting Information). CL reaction usually

247

is not complete at low KMnO4 concentration, and the self-absorption effect of KMnO4 at high

248

concentration will also affect the sensitivity of the method

249

result (Figure S7B, Supporting Information). Therefore, 5.0×10-5 mol L-1 KMnO4 based on the

250

experimental data is selected as the operating condition. The luminol-KMnO4 reaction usually takes

251

place in an alkaline medium. The biggest CL signal of the pyriden-luminol-KMnO4 system in our

252

experiment is obtained at NaOH concentration range from 0.6 to 1.0 mol L-1 (Figure S7C, Supporting

253

Information). Two peristaltic pumps are used to transport the reactants in this experiment, thus the flow

254

rate not only affects the degree of CL reaction but also causes the waste of reagents 19. When the flow

255

rate of two peristaltic pumps are set at 2.8 mL min-1 (P1, luminol, and KMnO4) and 4.0 ml min-1 (P2,

256

NaOH, and analytes), respectively, the relative CL signal are suitable (Figure S8, Supporting

257

Information).

258

Interference Study. The effect of the presence of foreign substances in solution, on pyridaben

259

determination by CL with ultrasonic assistance, is tested. The tolerable concentration ratios with respect

260

to 2.0 µg L-1 pyridaben for interference at 5% level are over 10,000 for Na+, K+, Ca2+, Mn2+, Cl-, SO42-,

261

CO32-, NO3- and H2PO4-; 2000 for Ba2+, Mg2+, Al3+ and Zn2+; 500 for methanol, ethanol, oxalate, tartrate,

262

urea; 100 for ascorbic acid, L-cysteine, Cu2+, Fe3+, Cr3+, Co2+ and Ni2+. The detailed results are listed in

263

Table 2.

264

Table 2. Effect of coexisting substances on the determination of 2.0 µg L-1pyridaben.

15-18

. Our experimental data also confirms this conclusion. Although, briefly, the CL

17

. The experimental data show a similar

13 Environment ACS Paragon Plus

Journal of Agricultural and Food Chemistry

Species Cu2+

Co2+

Fe3+

Ni2+

Cr3+ Na+ K+ Ca2+ Ba2+ Mg2+ Al3+

C, mg L-1 Recovery, % 0.1 101 0.2 105 1.0 121 0.1 97 0.2 95 1.0 118 0.1 99 0.2 104 1.0 112 0.1 97 0.2 102 1.0 106 0.1 105 0.2 104 1.0 107 20 96 20 97 20 97 4 98 4 102 4 104

Species methanol oxalate ethanol tartrate urea ascorbic acid L-cysteine

ClNO3H2PO4CO32SO42HPO42-

C, mg L-1 1.0 5.0 1.0 5.0 1.0 5.0 1.0 5.0 1.0 5.0 0.2 0.5 0.1 0.2 1.0 20 20 20 20 20 20

Page 14 of 30

Recovery, % 98 92 103 94 97 90 95 91 102 94 96 87 102 95 81 101 99 104 98 97 105

265

The mechanism of the enhancing effect on the CL signal is considered as a kind of energy transfer

266

process. Hence, some agrochemicals may also enhance the luminescence signal of lumilo-oxidant after

267

ultrasonic treatment. Experimental data show that the presence of 10.0 µg L-1 substances in 2.0 µg L-1

268

pyridaben sample solution produce 35% (picoxystrobin), 43% (azoxystrobin) and 27% (fenpyroximate)

269

positive interference; 20.0 µg L-1 substances in 2.0 µg L-1 pyridaben can lead to 52% (picoxystrobin),

270

69% (azoxystrobin) and 58% (fenpyroximate) changes. Besides, the CL detector itself does not have

271

selective analysis function. These factors will lead to problems, that is the presented method can not be

272

used directly for complex sample analysis. We are seeking for suitable ways (e.g. combination with

273

chromatographic separation or selective extraction for multiple-residues samples analysis) to resolve

274

this problem.

275

Performance and Validation of the Procedure. Under the selective conditions, linear revision

276

diagram is available in the scale of 0.8-100.0µg L-1 with the linear regression equations: IF=57.67 +

14 Environment ACS Paragon Plus

Page 15 of 30

Journal of Agricultural and Food Chemistry

277

214.03 C. C in the equation is the pyridaben concentration (µg L-1). The regression coefficient (r2) is

278

0.9974. The limit of detection (LOD) of pyridaben for this method is 0.085 µg L-1, calculated by taking

279

3 times the standard deviation of the blank solution divided by the slope from 11 measurements. The

280

limit of quantitation is 0.284 µg L-1. An analytic frequency of 6 h-1 (or 15 h-1 with 3min DFUT and the

281

LOQ is 1.025 µg L-1) and an RSD value of 1.3% (at the 20.0 µg L-1 level for eleven replicate

282

determinations) are also obtained. Table 3 covers the merits of analytical data achieved by using on-line

283

DFUT coupled with CL for sample detection and the comparison of analytical performance with several

284

other methods are also listed. The sensitivity and precision are superior or at least at the same level as

285

reported methodologies.

286

Table 3. Comparison of analytical parameters with other methods. Analytical Method

Linear range, µg L-1

LOD, µg L-1

RSD, %

Ref.

DFUT-CL a

0.8-100.0

0.085