Fast Drying Boosted Performance Improvement of Low-Temperature

Subscriber access provided by University of Sussex Library

Article

Fast drying boosted performance improvement of lowtemperature paintable carbon-based perovskite solar cell Qianqian Chu, Bin Ding, Yan Li, Lili Gao, Qi Qiu, ChengXin Li, Chang-Jiu Li, Guanjun Yang, and Baizeng Fang ACS Sustainable Chem. Eng., Just Accepted Manuscript • DOI: 10.1021/ acssuschemeng.7b01556 • Publication Date (Web): 24 Sep 2017 Downloaded from http://pubs.acs.org on September 24, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

ACS Sustainable Chemistry & Engineering is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Fast drying boosted performance improvement of low-temperature paintable carbon-based perovskite solar cell Qian-Qian Chu,† Bin Ding, † Yan Li, † Li-Li Gao,† Qi Qiu,‡ Cheng-Xin Li,† Chang-Jiu Li,† GuanJun Yang*,† and Baizeng Fang*§ †

State Key Laboratory for Mechanical Behavior of Materials, School of Materials Science and

Engineering, Xi’an Jiaotong University, 28 West Xianning Road,Xi’an, Shaanxi, 710049, P. R. China. * Email: ygj@ mail.xjtu.edu.cn (G. Yang). ‡

College of Chemistry and Environmental Engineering, Shenzhen University, 3688 Nanshan

Road, Shenzhen, Guangdong, 518060, P. R. China §

Department of Chemical & Biological Engineering, University of British Columbia, 2360 East

Mall, Vancouver, B.C. V6T 1Z3, Canada. * Email: [email protected] (B. Fang)

ABSTRACT: Low-temperature paintable carbon-based perovskite solar cells have been acknowledged as a promising photovoltaic device. However, the organometal trihalide perovskite film is always degraded by the solvents in the carbon paste, resulting in a fairly low efficiency. Unfortunately, in a conventional drying process, the movements of solvent molecules from a carbon paste to atmosphere are greatly obstructed by the bi-scale size of carbon black and graphite, which creates an extremely long evaporation path and drying time. To solve the problem, we have developed a simple, highly efficient and scalable method, gas pump method (GPM) to dry the carbon paste very quickly which demonstrates a 7 times drying rate compared

ACS Paragon Plus Environment

1


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 2 of 35

with the conventional drying. As a result, the perovskite films covered by the carbon electrode (CE) dried by the GPM keep a uniform and continuous surface morphology, and the champion solar cell reveals a conversion efficiency of 12.30% with the area of 0.1 cm2 and an open circuit voltage of 1.03 V, which are much higher than that (i.e., 4.73% and 0.81 V, respectively) observed for the PSC without GPM. Furthermore, the long-time stability test shows that the solar cells with the as-prepared CE retain more than 90% of its initial power conversion efficiency after 720 h. KEYWORDS: Low-temperature processing, perovskite solar cell, carbon paste, fast drying, gas pump method, photovoltaic property

INTRODUCTION The organometal trihalide perovskite acting as the light absorber in the thin film solar cells has attracted much attention due to its excellent and unique characteristics, such as appropriate direct band gap, high light-absorption efficiency, and excellent carrier transportation.1-4 Since the first report about perovskite solar cells (PSCs) achieved PCE of 3.8% by Miyasaka and co-workers in 2009,5 the PSCs have experienced continuous and rapid development. Recently, the certified recorded power conversion efficiency of PSCs has increased to 22.1%.6 The excellent PCEs also suggest that PSC is a promising candidate for the conventional solar cells.7-9 However, there still exist some barriers for commercialization of PSCs.10-12 The commonly reported architecture of PSCs always includes a noble metal electrode, such as Au and Ag, a p-type organic small-molecular polymeric hole transporting material (HTM), such as spiro-OMeTAD and PTAA,13-15 which are extremely expensive. Moreover, the related preparation methods significantly decrease the stability and hinder the industrialization of


2

Page 3 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


PSCs.13,15-18 To solve this problem, the carbon-based PSCs are recently chosen as a competitive alternative because carbon materials are abundant, economical and highly stable with a similar work function (-5.0 eV) as Au electrode (-5.1 eV).19-21 In addition, perovskite film has previously demonstrated unique ambipolar property, acting as both the light absorber and the hole transport layer (HTL). The PSCs with carbon electrode (CE) and no HTL were firstly proposed by Etgar, and the PSCs achieved a PCE of 5%.22 Although the manufacturing cost could be evidently reduced, the PCEs are lower compared with the PSCs with metal electrode and HTL. Therefore, many efforts have been made by researchers to tackle the problems affecting the photoelectric property of carbon-based PSCs. Because of the instability of the organometal trihalide perovskite in most solvents, it is really difficult to prepare a carbon layer by a solvent engineering process on the perovskite film.23-26 To avoid the dissolution of perovskite film during deposition of the carbon layer, some researchers prefabricated the carbon layer before spinning coating the perovskite layer. Han et al. developed a mesoporous scaffold (TiO2/Al2O3/NiO/carbon layer) infiltrated with the perovskite and achieved a PCE of 15%.16,17,27-29 Yang et al. achieved 11.02% efficiency by successively preparing the PbI2 and CE with a subsequent treatment in a CH3NH3I bath.30-32 Meng et al. developed a free-standing thermoplastic carbon film with good conductivity and flexibility as counter electrode by hot-press on the perovskite film and obtained an efficiency of 13.53%.33 Those complex devices could be improved by directly coating a low temperature carbon paste on the perovskite film. Consequently, some efforts have been directed in changing the composition of CE for the simplest paintable PSCs.32-34 Some groups chose graphene, carbon nanotubes as the additives, resulting in increasing production costs.35-37 Zhou et al. altered the percentage of graphite and carbon black with the resultant PCEs unsatisfactory.33 Ma et al. changed the solvent


3


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 4 of 35

of the carbon paste to chlorobenzene, a solvent compatible with the perovskite film, and achieved 9% efficiency based on a glass substrate and PCE of 4% based on flexible substrates.24,25 Nevertheless, the chlorobenzene solvent is very unfriendly to the human health and the environment. Furthermore, this carbon paste is not easy to reserve and transport. In this study, we report a simple, scalable and sustainable method, gas pump method (GPM), to dry the carbon paste in a vacuum environment. By this method, the solvents in the carbon paste evaporate quickly and the solvent molecules are pumped away immediately, resulting in a uniform carbon electrode. Moreover, the damage of the solvent in low temperature commercial carbon paste to the perovskite film substantially decreases, enabling a uniform morphology of the perovskite film. As a result, the as-prepared TiO2/CH3NH3PbI3/C HJ perovskite solar cells have demonstrated a PCE of 12.3%. With impressive stability, the as-developed carbon-based GPM-engineered PSCs show great potential based on the advantages such as the negligible dissolution, low electrode fabrication cost, simple and scalable low-temperature electrode preparation process, high efficiency and excellent stability. EXPERIMENTAL SECTION Materials. Transparent patterned fluorine-doped tin oxide (FTO) conductive glass substrates with the sheet resistance of 15Ω sq-1 were scratched by laser. The carbon paste and the precursor solution of compact TiO2 were commercially available chemicals (Weihua). The mesoporous TiO2 (20 nm, Aldrich) paste was diluted with anhydrous ethanol (1:7 weight ratio). The lead iodide (4.61g, PbI2, 99%) and the methylammonium (1.59 g, CH3NH3I, PLT) were mixed and stirred in N,N-dimethylformamide (10 ml, DMF, Sigma-Aldrich, 99.8%) at 40°C for 8h to prepare CH3NH3PbI3 precursor solution.


4

Page 5 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Fabrication of Perovskite Solar Cells. FTO glasses were ultrasonically cleaned by acetone, ethanol and deionized water for 15 min respectively in succession, and then treated in the UVzone cleaning for 30 min. Subsequently, the substrates were coated with a ~ 60 nm compact TiO2 layer by spin-coating method at 2000 rpm for 30 s, and then sintered at 450°C for 30 min. A 200 nm mesoporous TiO2 layer was deposited on the top of the compact layer by screen-printing method and then sintered at 500°C for 30 min. Perovskite precursor solution of 40wt.% was spin-coated on the mesoporous TiO2 layer at 3000 rpm for 10 s. Then the sample was immediately transferred to the gas pump system. The system was made up of a sample chamber, a valve, a large vacuum buffer tank and a pump. When the valve was turned on, the air pressure in the sample chamber quickly decreased to the setting pressure (1500Pa). In the vacuum environment, DMF evaporated rapidly and the evaporative molecules of the solvent was pumped away quickly. A brown, mirror-like perovskite film was formed in about 5 seconds. The film was annealed at 100°C on a hot plate for 15 min. After the commercial carbon paste (main solvents: isophorone, propylene glycol monomethyl ether and diethylene glycol monobutyl ether acetate; boiling points : 215.2 oC, 190 oC, 246.8 oC, respectively) was screening-printed on the perovskite film, the same gas pump method was used. A hot plate was placed under the bottom of the chamber to adjust the temperature of the sample to the drying temperature (100 °C) of the carbon paste, and the low pressure was set as 100Pa to accelerate the drying of the carbon paste The same operation of the device was used. When the resistance of the CE didn’t change with the increase of the drying time any more, the drying process was complete (Figure S1, Supporting Information). Characterization. The surface of the perovskite films and fracture morphologies of the PSCs were characterized by a field-emission scanning electron microscope (SEM, TESCAN MIRA 3


5


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 6 of 35

LMH). The four-probe tests were performed on the CE of 2.5 cm × 1.1 cm for their conductivity measurement. X-ray diffraction (XRD) patterns were acquired by a Rigaku Ultima X-ray diffractometer (Cu Kα) to analyze the structure of the perovskite film. A compact steady-state spectrophotometer (Fluoromax-4, Horiba Jobin Yvon) with an excitation wavelength of 532 nm was employed to obtain the steady-state photoluminescence spectra. The photocurrent density– voltage (J-V) characteristics were measured with a Keithley 2400 source-meter with an AM 1.5 G filter (Sol3A, Oriel) equipped on a 450W Class AAA solar simulator under the illumination of 100 mW/cm2. The devices were measured at a scan step of ca. 23.7 mV (60 points in total) and a delay time of 500 ms. The electrochemical properties of the perovskite solar cell were investigated by electrochemical impedance spectroscopy (EIS, Zennium IM6, Zahner). The spectroscopies were measured with a step of 0.05 V and at a frequency ranging from 1 MHz to 100 mHz with an AC amplitude of 20 mV under a LED light with an intensity of 100 mW/cm2. RESULTS AND DISSCUTION Drying Process of Carbon Paste. Figure 1 shows the schematic diagrams for the screenprinting processing of a carbon paste and the tendency for the solvent molecules to infiltrate in and dissolve the perovskite film, which is unstable in most drying processes of a carbon paste under various conditions. After a carbon paste is screen printed on a perovskite film, the solvent molecules at the wet top surface of the carbon paste evaporate to the air (Figure 1a) and those located near the interface between the carbon paste and the perovskite tend to infiltrate in and dissolve the perovskite film. From the detailed structure of carbon paste in Figure 1b, the main conductive materials are carbon black and graphite. In the drying processing, the perovskite film was dissolved by the solvents in the carbon paste until the paste was completely dried. As a result, the dissolution duration of the perovskite is equal to the overall duration for the drying of


6

Page 7 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


carbon paste. Thus, the reduction in the drying time could alleviate the damage of the solvent to the perovskite film. Figure 1c illustrates the drying process of the carbon paste with conventional method (heating in 100 oC). In the first stage, the surface of carbon layer is wet, thus the solvents vaporize quickly. In the second stage, after the surface of the carbon paste was dried, the solvent molecules vaporize from the dry and wet interface and then get into the air environment. However, it’s very difficult for the molecules to flee away from the carbon layer.

38,39

At the

nano-scale, there exist many twists and turns among the carbon black particles, hence the path length for the solvent molecules fleeing to the atmosphere from the wet interface increases. At the micro-scale, the solvent molecules will be rebounded repeatedly because of the obstruction of the graphite with the size of several or even more than ten micrometers, and the path length increases in the carbon layer. The obstruction of the carbon black and graphite in nano- and micro- scale results in a very long path which result in the extended length of the path, and therefore it’s very difficult to dry the carbon paste quickly. The slow diffusion of the gas phase solvents will restrain the evaporation of the liquid phase solvents. If the drying time is significantly shortened, the damage of perovskite film by the solvents in carbon paste will be decreased largely (Figure 1d).


7


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 8 of 35

Figure 1. (a) The well prepared carbon paste on FTO/TiO2/Perovskite, (b) The detailed structure of carbon paste on FTO/TiO2/Perovskite, (c) The long path length for solvent molecules and the serious damage of perovskite by conventional drying method in the drying process, (d) The well retained perovskite film by fast drying. Figure 1c shows the obstruction of carbon black and graphite for the movement of solvents in carbon paste increases the drying duration of carbon paste resulting in the serious damage of perovskite under conventional drying, Figure 1d shows the fast drying method could reduce the drying time of carbon paste keeping the perovskite film well retained with little dissolution degradation.

To solve the problem, we introduced GPM to accelerate the drying process of the carbon paste. The fabrication process is illustrated in Figure 2 for carbon-based PSCs with GPM. Firstly, according to the method mentioned previously, a brown, mirror-like perovskite film was prepared and annealed at 100 °C on a hot plate for 15 min (Figure 2a).14,40,41 In Figure S2


8

Page 9 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


(Supporting Information), the dense, uniform, and full-coverage perovskite films with uniform grain size were obtained.40 XRD measurements were conducted to investigate the crystal structure of the CH3NH3PbI3 films, and the results in Figure S3 (Supporting Information) reveals the major diffraction peaks of the perovskite phase of CH3NH3PbI3.42-44 Also, Figure S4a (Supporting Information) shows the absorption spectra of the perovskite films on TiO2/FTO substrate and FTO substrate. The results indicate that the absorption intensity of the perovskite films on different substrates was almost the same, suggesting that the TiO2 film on the FTO substrate can hardly influence the absorption of perovskite films. Compared with the perovskite/FTO substrate, the photoluminescence emission spectra of the perovskite/TiO2/FTO substrate display a clear quenching suggesting effective extraction of carriers by TiO2 (Figure S4b, Supporting Information). In order to obtain charge carrier life time, we investigated the time-resolved photoluminescence (PL) decay curves of perovskite films prepared on FTO derived from the MAPbI3 (Nature drying, ND) and MAPbI3 (GPM) as shown in Figure S5. With global biexponential fits, the calculated time constants are τ1 = 3.38 ± 0.09 ns, τ2 = 52.81 ± 0.31 ns and τ1 = 4.01 ± 0.06 ns, τ2 =80.13 ± 1.09 ns, respectively. The longer lifetime of charge carriers based on GPM indicates a lower defect concentration and a lower recombination rate. 4547


9


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 10 of 35

Figure 2. Fabrication process of TiO2/perovskite/carbon solar cell with GPM. a) Perovskite film coated on TiO2/FTO, b) a wet carbon paste applied on the substrate, c) carbon paste dried by a gas pump, and d) the dried carbon paste on the substrate.

Subsequently the commercial carbon paste was screen printed on the perovskite film (Figure 2b), and the sample was placed in the gas pump system. With gas pumping, (Figure 2c) the solvents in the carbon paste evaporated quickly in the vacuum environment and the molecules of evaporative solvents moved rapidly away from the carbon layer to the sample chamber. In the meanwhile, the molecules of solvents in the sample chamber were pumped away immediately. Therefore, the carbon paste with GPM was dried quickly and the carbon electrode was well prepared. (Figure 2d) However, compared to the carbon paste drying without GPM, the solvents in the carbon paste evaporated slowly in the atmosphere, the gaseous molecules’ movements were disordered and it took a long time for the molecules of solvents to escape from the carbon layer. The drying time of the carbon paste with GPM would be much shorter than that without GPM.


10

Page 11 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Because the damage degree is inversely proportional to the drying rate, the drying rates with and without GPM were investigated. Figure 3a show that the drying rate with GPM is about 7 times as fast as the rate without GPM for the carbon pastes with different thickness, and Figure S6 (Supporting Information) shows that the drying time of the carbon pastes with GPM decreases about 85% relative to those without GPM. Meanwhile, the resistance of the CEs in different thickness was tested. As seen in Figure 3b, the resistances measured by the four-probe method are almost the same whether the samples with the same thickness were dried with or without GPM. According to the data for both the conductivity and the drying time, the CE prepared by GPM could decrease the dissolution time but keep good conductivity as the sample prepared without GPM. Based on the resistance and the drying rate, CEs with a proper thickness (about 20 µm) were utilized to prepare the PSCs. The resistance and the drying time of the CE are 24.9 Ω and 3 min, respectively.

Figure 3. (a) Drying rate of the carbon paste with and without GPM. (b) The resistance of CE in different thickness with and without GPM.

The PSCs with CEs prepared with GPM (W/ GPM) or without GPM (W/O GPM) were constructed and SEM images were taken to observe the damage of the solvent to the perovskite film. Compared with the perovskite film of without CE device (W/O CE) (Figure 4a and 4b), the perovskite film of the W/O GPM device was destroyed seriously and in some regions the perovskite film was even almost completely eroded (Figure 4d and 4e). However, the perovskite


11


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 12 of 35

film of the W/ GPM device was barely destroyed (Figure 4h and 4i). It’s evident that with the decrease in the drying time of the carbon paste contributed by GPM, the damage to the perovskite film was substantially weakened. In order to further compare the damage of the W/O GPM device and W/ GPM device, the localized perovskite film thickness was measured and counted. The average thickness of the perovskite film of W/O CE device, W/ GPM device, W/O GPM device is 355±24 nm，344±48 nm, and 206±82 nm, respectively (Figure 4c, 4f, and 4i). The statistical data indicate serious destruction of the perovskite film of W/O GPM device as compared with the distribution of perovskite film’s thickness of W/ GPM device.


12

Page 13 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Figure 4. (a, d, g) Cross-sectional view of FTO/c-TiO2/m-TiO2/perovskite film, cross-sectional view of W/O GPM device, and W/ GPM device; (b, e, h) Magnified images of a, d, and g respectively; Thickness of perovskite film of (c) W/O CE device, (f) W/O GPM device, and (i) W/ GPM device.

Furthermore, the distribution of perovskite film’s thickness of W/O GPM device is in a wider range. Interestingly, the perovskite film of W/ GPM device has almost the same thickness and fluctuation as the perovskite film of W/O CE device, and thus it can be expected that the W/ GPM device has better photo- electrical properties than the PSC without GPM. Photovoltaic Properties of Various Carbon-based PSCs. The photovoltaic performance of the two devices, prepared W/ GPM or W/O GPM were tested under an illumination of 100 mW/cm2. Figure 5a shows the J-V curves of the W/ GPM device, which demonstrated a PCE up to 12.3% with the area of 0.1 cm2, Voc of 1.03 V, FF of 0.56 and Jsc of 21.4 mA/cm2. Moreover, the parameters derived in the reverse scan with a scan step of 23.7 mV and a delay time of 1000 ms are almost the same as the forward scan. Compared with the J-V curves recorded for the W/O GPM device as shown in Figure 5b, the W/ GPM device presents much higher PCE, Jsc, Voc and FF than the W/O GPM device. Furthermore, the output of current density and PCE at the maximum power point of the champion cell was measured at a bias voltage of 0.74 V, and as shown in Figure 5c the current density is stabilized at 15.7 mA/cm2 and PCE stabilized at 11.6% in 600 s. This indicates that the W/ GPM device could deliver a large PCE along with excellent output stability.


13


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 14 of 35

Figure 5. Current-voltage characteristics of (a) W/ GPM device, (b) W/O GPM device. (c) The corresponding output of PCE and current density at maximum power point of 0.74 V for the champion cell under a simulated AM 1.5G solar illumination of 100 mW/cm2.

To further investigate the quality of the GPM-prepared perovskite solar cell, W/O GPM devices and 36 W/ GPM devices were fabricated and the corresponding photoelectric parameters were summarized. The average PCE, Voc, Jsc and FF (Figure 6a-d) are 10.6 ± 0.65%, 1.02 ± 0.02 V, 19.30 ±0.91 mA/cm2, and 0.54 ± 0.03, respectively, for the W/ GPM devices. In contrast, because of the heterogeneous and discontinuous perovskite film in the W/O GPM devices which deleteriously affects charge dissociation/transportation/recombination, the W/O GPM devices exhibited much worse photoelectric properties with a wide variation. The statistical parameters of the W/ GPM devices and the W/O GPM devices are listed in Table S1 (Supporting Information) and Table S2 (Supporting Information). Compared with the W/O GPM devices, the excellent reproducibility of the W/ GPM devices can be attributed to the higher uniformity of the CH3NH3PbI3 films created by the rapid drying of the carbon paste.


14

Page 15 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Figure 6. (a) The PCE, (b) the open circuit voltage (Voc), (c) the short circuit current density (Jsc) and (d) the fill factor (FF) of the as-constructed 36 carbon based perovskite solar cells prepared by GPM.

To further investigate the internal electrical properties of the W/ GPM device and W/O GPM device, the electrochemical impedance spectroscopy (EIS) were measured under white light with a power density of 100 mW/cm2. Figure 7a shows the Nyquist plots from 1 MHz to 10Hz for the W/ GPM device and W/O GPM device under illumination. The contrast of the two curves based on the two different devices is very significant. From the enlarged image (Figure 7b), there are two circles in the frequency range for each curve. The circle at the high frequency region (106 to 104 Hz) is related to the electron transfer process on the counter electrode. The second one at the intermediate frequency region (104 to 10 Hz) is for the charge recombination at the TiO2/perovskite interface. The analysis for the low frequencies (< 10 Hz) would be complicated because of the multi-interfacial recombination or electron/ion diffusion.48-51 Therefore, an equivalent circuit consisting of three lumped RC-circuits in series, as shown in Figure S7b (Supporting Information) which has been verified, is used to fit the impedance data.


15


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 16 of 35

Figure 7. (a) Nyquist plots of the cell with and without GMP under the -0.9 V bias. (b) An enlarged view of Figure 7a. Nyquist plots of the cell (c) with GMP and (d) without GPM. (e) The RCE and (f) Rct of the cell with GMP and without GPM.

In order to clearly understand the effect of drying process on the perovskite film, the Nyquist plots (Figure 7c and d) and bode plots (Figure S7a and b, Supporting Information) in different bias voltages were measured. Based on the equivalent circuit,52,53 the series resistances (RS) were about 12.3 Ω for W/ GPM device and 23.8 Ω for W/O GPM device, suggesting highly conductivity of perovskite/carbon interface. The smaller series resistance of the W/ GPM device contributes to a higher performance of PSCs, especially a higher fill factor. The charge exchange resistances (RCE) and charge recombination resistances were derived for the W/ GPM device and W/O GPM device, and are presented in Figure 7e and f respectively. At different bias voltages,


16

Page 17 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


RCE and Rct decreased with the increasing bias voltage. More importantly, RCE of the W/O GPM device is greater than that of the W/ GPM device, indicating that the charge transfer process of the W/ GPM device at the CE is more efficient. In the W/O GPM device, the perovskite film is dissolved seriously, and the dissolved perovskite particles nucleate and grow on the face of the carbon particles which may result in a poor contact between the carbon particles. A better charge transfer is exhibited in the W/ GPM device. In Figure 7f, Rct of the W/O GPM device is less than that of the W/ GPM device, indicating that the W/O GPM device has a poor charge extraction in the TiO2/perovskite interface. The poor perovskite film morphology due to the dissolution of the perovskite particles caused by the solvents in the carbon based PSC has been reported to be very detrimental to the device performance because this dissolution not only causes an electrical shorting but also is against the charge dissociation and transportation, and favors the charge recombination. According to the comparison of RCE and Rct between the two devices, the gas pump assisted perovskite solar cells keep the good perovskite morphology, leading to excellent electrical properties. To probe the stability of the devices, the PSCs with and without GPM were placed under the ambient atmosphere and the natural illumination at room temperature for 720 h.49 As time went on, the PCE, voltage, current density and FF of the W/O GPM and W/ GPM devices all degraded, as shown in Figure 8. The W/O GPM devices suffered from a rapid degradation and retained less than 70% of their initial PCE after 120 h and 25% after 720 h. Interestingly, the W/ GPM devices remained nearly the same PCE as its initial value after 120 h and retained more than 90% of its initial PCE after 720 h. In 720 h, the voltage, current density, and FF of the W/ GPM device barely degraded. However, the values for these parameters of the W/O GPM device show a sharp decrease. Evidently, the significant difference in the long-term stability was determined by if the


17


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 18 of 35

GPM treatment was used to dry the carbon paste. The rapid drying of the W/ GPM devices reduced the damage time from the solvents in the carbon paste to the perovskite film, and kept the uniform morphology of the perovskite film. As a result, in the long-term stability test, the perovskite film was not easy to be damaged by the oxygen and water vapor in the atmosphere.52,54 In all, compared to the carbon-based PSCs prepared without GPM，this lowcost and stable PSCs fabricated with GPM are very promising photovoltaic devices.

Figure 8. (a) The normalized PCE, (b) the normalized voltage, (c) the normalized current density, and (d) the normalized fill factor shown as a function of test time for the perovskite solar cells with the champion PCE and of W/ and W/O GPM devices.

CONCLUSIONS In summary, we have successfully prepared CE through a simple and cost-effective lowtemperature preparation process which could greatly increase the evaporation rate of the solvents in the carbon paste. The GPM could significantly reduce the drying time of a CE with a thickness of 20 µm from 20 min to 3 min. Accordingly, the dissolution time of the perovskite film decreased considerably, and the average thickness of the perovskite film of the W/ GPM device has a comparatively small decrease (i.e., from 355 to 344 nm). A PCE up to 12.3% along with a


18

Page 19 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Voc of 1.03 V have been demonstrated by the W/ GPM device. The W/ GPM devices also exhibited an excellent stability, remaining nearly the same as its initial PCE after 120 h and retaining more than 90% of its initial PCE after 720 h. In all, the high reproducibility and efficiency of the devices based on GPM make it promising for the commercial production of the perovskite solar cells. ASSOCIATED CONTENT Supporting Information: XRD for the perovskite film, PL emission spectra of perovskite film on FTO and TiO2/FTO, surface morphology of perovskite film, Bode plots of W/GPM and W/O GPM device, photovoltaic performance of the 36 W/ (or W/O) GPM devices, stability tests results. The files are available free of charge. AUTHOR INFORMATION Corresponding Authors *

Email: ygj@ mail.xjtu.edu.cn (G. Yang).

*

Email: [email protected] (B. Fang).

Notes The authors declare no competing financial interests. ACKNOWLEDGEMENTS The work was supported by the National Program for Support of Top-notch Young Professionals. REFERENCES


19


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

(1)

Page 20 of 35

Stranks, S. D.; Eperon, G. E.; Grancini, G.; Menelaou, C.; Alcocer, M. J.; Leijtens, T.;

Herz, L. M.; Petrozza, A.; Snaith, H. J., Electron-hole diffusion lengths exceeding 1 micrometer in an organometaltrihalide perovskite absorber. Science 2013, 342, 341-344. (2)

Dong, Q.; Fang, Y.; Shao, Y.; Mulligan, P.; Qiu, J.; Cao, L.; Huang, J., Solar cells.

Electron-hole diffusion lengths > 175 µm in solution-grown CH3NH3PbI3 single crystals. Science 2015, 347, 967-970. (3)

Xing, G.; Mathews, N.; Sun, S.; Lim, S. S.; Lam, Y. M.; Grätzel, M.; Mhaisalkar, S.;

Sum, T. C., Long-range balanced electron-and hole-transport lengths in organic-inorganic CH3NH3PbI3. Science 2013, 342, 344-347. (4)

Ball, J. M.; Lee, M. M.; Hey, A.; Snaith, H. J., Low-temperature processed meso-

superstructured to thin-film perovskite solar cells. Energy Environ. Sci. 2013, 6, 1739-1743. (5)

Kojima, A.; Teshima, K.; Shirai, Y.; Miyasaka, T., Organometal Halide Perovskites as

Visible-Light Sensitizers for Photovoltaic Cells. J. Am. Chem. Soc. 2009, 131, 6050-6051. (6)

http://www.nrel.gov/.

(7)

Green, M. A.; Emery, K.; Hishikawa, Y.; Warta, W.; Dunlop, E. D., Solar cell efficiency

tables (version 41). Prog. Photovolt: Res. Appl. 2013, 21, 1-11. (8)

Park, N. G., Organometal Perovskite Light Absorbers Toward a 20% Efficiency Low-

Cost Solid-State Mesoscopic Solar Cell. J. Phys. Chem. Lett. 2013, 4, 2423-2429. (9)

Bi, D.; Tress, W.; Dar, M. I.; Peng, G.; Luo, J.; Renevier, C.; Schenk, K.; Abate, A.;

Giordano, F.; Baena, J. P. C., Efficient luminescent solar cells based on tailored mixed-cation perovskites. Sci. Adv. 2016, 2, e1501170-e1501170. (10)

Huang, L.; Xu, J.; Sun, X. X.; Xu, R.; Du, Y. Y.; Ni, J.; Cai, H. K.; Li, J.; Hu, Z. Y.;

Zhang, J. J, New Films on Old Substrates: Toward Green and Sustainable Energy Production via


20

Page 21 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Recycling of Functional Components from Degraded Perovskite Solar Cells, ACS Sustainable Chem. Eng. 2017, 5, 3261-3269. (11)

Xiao, Y.; Han, G.; Li, Y.; Li, M.; Wu, J., Electrospun lead-doped titanium dioxide

nanofibers and the in situ preparation of perovskite-sensitized photoanodes for use in high performance perovskite solar cells. J. Mater. Chem. A 2014, 2, 16856-16862. (12)

Niu, G.; Guo, X.; Wang, L., Review of Recent Progress in Chemical Stability of

Perovskite Solar Cells. J. Mater. Chem. A 2015, 3, 8970-8980. (13)

Zhang, F.; Yang, X.; Cheng, M.; Wang, W.; Sun, L., Boosting the Efficiency and the

Stability of Low Cost Perovskite Solar Cells by using CuPc Nanorods as Hole Transport Material and Carbon as Counter Electrode. Nano Energy 2016, 20, 108-116. (14)

Ding, B.; Li, Y.; Huang, S. Y.; Chu, Q. Q.; Li, C.; Li, C.; Yang, G. J., Material

nucleation/growth competition tuning towards highly reproducible planar perovskite solar cells with efficiency exceeding 20%. J. Mater. Chem. A 2017, DOI:10.1039/C7TA00027H. (15)

Luo, J.; Jia, C.; Wan, Z.; Han, F.; Zhao, B.; Wang, R., The novel dopant for hole-

transporting material opens a new processing route to efficiently reduce hysteresis and improve stability of planar perovskite solar cells. J. Power Sources 2017, 342, 886-895. (16)

Tsai, C. M.; Wu, G. W.; Narra, S.; Chang, H. M.; Mohanta, N.; Wu, H. P.; Wang, C. L.;

Guang Diau, E. W., Control of preferred orientation with slow crystallization for carbon-based mesoscopic perovskite solar cells attaining efficiency 15%. J. Mater. Chem. A, 2016, 5, 739-747. (17)

Han, H.; Zhang, L.; Liu, T.; Liu, L.; Hu, M.; Yang, Y.; Mei, A., The Effect of Carbon

Counter Electrode on Fully Printable Mesoscopic Perovskite Solar Cell. J. Mater. Chem. A 2015, 3, 9165-9170.


21


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

(18)

Page 22 of 35

Yuan, H.; Debroye, E.; Janssen, K.; Naiki, H.; Steuwe, C.; Lu, G.; Moris, M.; Orgiu, E.;

Ujii, H.; Schryver, F. D., Degradation of Methylammonium Lead Iodide Perovskite Structures through Light and Electron Beam Driven Ion Migration. J. Phys. Chem. Lett. 2016, 7, 561-566. (19)

Gholipour, S.; Correa-Baena, J. P.; Domanski, K.; Matsui, T.; Steier, L.; Giordano, F.;

Tajabadi, F.; Tress, W.; Saliba, M.; Abate, A., Highly Efficient and Stable Perovskite Solar Cells based on a Low-Cost Carbon Cloth. Adv. Energy Mater. DOI: 10.1002/aenm.201601116. (20)

Leu, Y. A.; Yeh, M. H.; Lin, L. Y.; Li, T. J.; Chang, L. Y.; Shen, S. Y.; Li, Y. S.; Chen,

G. L.; Chiang, W. H.; Lin, J. J., Thermally Stable Boron-doped Multi-walled Carbon Nanotubes as a Pt-free Counter Electrode for Dye-sensitized Solar Cells. ACS Sustainable Chem. Eng. 2016, 5, 537-546. (21)

Reddy, K. G.; Deepak, T. G.; Anjusree, G. S.; Thomas, S.; Vadukumpully, S.;

Subramanian, K. R.; Nair, S. V.; Nair, A. S., On global energy scenario, dye-sensitized solar cells and the promise of nanotechnology. Phys. Chem. Chem. Phys. 2014, 16, 6838-6858. (22)

Etgar, L.; Gao, P.; Xue, Z.; Peng, Q.; Chandiran, A. K.; Liu, B.; Nazeeruddin, M. K.;

Grätzel, M., Mesoscopic CH3NH3PbI3/TiO2 Heterojunction Solar Cells. J. Am. Chem. Soc. 2012, 134, 17396-17399. (23)

Xiao, M.; Huang, F.; Huang, W.; Dkhissi, Y.; Zhu, Y.; Etheridge, J.; Gray-Weale, A.;

Bach, U.; Cheng, Y.B.; Spiccia, L. A Fast Deposition-Crystallization Procedure for Highly Efficient Lead Iodide Perovskite Thin-Film Solar Cells. Angew. Chem. Int. Ed.. 2014, 53, 98989903. (24)

Zhou, H.; Shi, Y.; Dong, Q.; Zhang, H.; Xing, Y.; Wang, K.; Du, Y.; Ma, T., Hole-

Conductor-Free, Metal-Electrode-Free TiO2/CH3NH3PbI3 Heterojunction Solar Cells Based on a Low-Temperature Carbon Electrode. J. Phys. Chem. Lett 2014, 5, 3241-3246.


22

Page 23 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


(25)

Zhou, H.; Shi, Y.; Wang, K.; Dong, Q.; Bai, X.; Xing, Y.; Du, Y.; Ma, T., Low-

Temperature Processed and Carbon-Based ZnO/CH3NH3PbI3/C Planar Heterojunction Perovskite Solar Cells. J. Mater. Chem. C 2015, 119, 4600-4605. (26)

You, J.B.; Meng, L.; Song, T.B.; Guo, T.F.; Yang, Y.; Chang W.H.; Hong, Z.R.; Chen,

H.J.; Zhou, H.P.; Chen, Q., Improved air stability of perovskite solar cells via solution-processed metal oxide transport layers. Nature Nanotech. 2016, 11, 75-81 (27)

Mei, A.; Li, X.; Liu, L.; Ku, Z.; Liu, T.; Rong, Y.; Xu, M.; Hu, M.; Chen, J.; Yang, Y.;

Gratzel, M.; Han, H., A hole-conductor-free, fully printable mesoscopic perovskite solar cell with high stability. Science 2014, 345, 295-298. (28)

Yang, Y.; Ri, K.; Mei, A.; Liu, L.; Hu, M.; Liu, T.; Li, X. ;Han, H., Size effect of TiO2

nanoparticles on the printable mesoscopic perovskite solar cell. J. Mater. Chem. A 2015, 3, 91039107. (29)

Zhang, L. J.; Liu, T. F.; Liu, L. F.; Hu, M.; Yang, Y.; Mei, A. Y.; Han, H. W. The effect

of carbon counter electrode on fully printable mesoscopic perovskite solar cell. J. Mater. Chem. A 2014, 3, 9165-9170. (30)

Chen, H.; Wei, Z.; He, H.; Zheng, X.; Wong, K. S.; Yang, S., Solvent Engineering

Boosts the Efficiency of Paintable Carbon‐Based Perovskite Solar Cells to Beyond 14%. Adv. Energy Mater. 2016, 6, DOI: 10.1002/aenm.201502087. (31)

Wei, Z.; Yan, K.; Chen, H.; Yi, Y.; Zhang, T.; Long, X.; Li, J.; Zhang, L.; Wang, J.;

Yang, S., Cost-efficient clamping solar cells using candle soot for hole extraction from ambipolar perovskites. Energy Environ. Sci. 2014, 7, 3326-3333.


23


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

(32)

Page 24 of 35

Liu, Z.; Shi, T.; Tang, Z.; Sun, B.; Liao, G., Using a low-temperature carbon electrode for

preparing hole-conductor-free perovskite heterojunction solar cells under high relative humidity. Nanoscale 2015, 8, 7017-7023. (33)

Wei, H.; Xiao, J.; Yang, Y.; Lv, S.; Shi, J.; Xu, X.; Dong, J.; Luo, Y.; Li, D.; Meng, Q.,

Free-standing flexible carbon electrode for highly efficient hole-conductor-free perovskite solar cells. Carbon 2015, 93, 861-868. (34)

Wang, H.; Hu, X.; Chen, H., The effect of carbon black in carbon counter electrode for

CH3NH3PbI3/TiO2 heterojunction solar cells. RSC Adv. 2015, 5, 30192-30196. (35)

Tsai, C. M.; Wu, G. W.; Narra, S.; Chang, H. M.; Mohanta, N.; Wu, H. P.; Wang, C. L.;

Diau, W. G., Control of preferred orientation with slow crystallization for carbon-based mesoscopic perovskite solar cells attaining efficiency 15%. J. Mater. Chem. A 2016, 5, 739-747. (36)

Schulz, P.; Dowgiallo, A. M.; Yang, M.; Zhu, K.; Blackburn, J. L.; Berry, J., Charge

Transfer Dynamics between Carbon Nanotubes and Hybrid Organic Metal Halide Perovskite Films. J. Phys. Chem. Lett. 2016, 7, 418-425. (37)

Wei, Z.; Chen, H.; Yan, K.; Zheng, X.; Yang, S., Hysteresis-free Multi-wall Carbon

Nanotube-based Perovskite Solar Cells with a High Fill Factor. J. Mater. Chem. A 2015, 3, 24226-24231. (38)

Toyohiko, Y.; solvent evaporation from paint films. Progr. Org. Coatings 1972, 1, 73-90.

(39)

Hansen, C. M.; The Process of Solvent Evaporation. In The Three Dimensional Solubility

Parameter and Solvent Diffusion Coefficient; Hansen, C. M.; Danish Technical Press: Copenhagen, 1967


24

Page 25 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


(40)

Ding, B.; Gao, L.; Liang, L.; Chu, Q.; Song, X.; Li, Y.; Yang, G.; Fan, B.; Wang, M.; Li,

C., Facile and Scalable Fabrication of Highly Efficient Lead Iodide Perovskite Thin-Film Solar Cells in Air Using Gas Pump Method. ACS Appl. Mater. Interfaces 2016, 8, 20067-20073. (41)

Dkhissi, Y.; Huang, F.; Rubanov, S.; Xiao, M.; Bach, U.; Spiccia, L.; Caruso, R. A.;

Cheng, Y. B., Low temperature processing of flexible planar perovskite solar cells with efficiency over 10%. J. Power Sources 2015, 278, 325-331. (42)

Chang, X.; Li, W.; Chen, H.; Zhu, L.; Liu, H.; Geng, H.; Xiang, S.; Liu, J.; Zheng, X.;

Yang, Y., Colloidal Precursor-Induced Growth of Ultra-Even CH3NH3PbI3 for HighPerformance Paintable Carbon-Based Perovskite Solar Cells. ACS Appl. Mater. Interfaces 2016, 8, 30184-30192. (43)

Hu, M.; Liu, L.; Mei, A.; Yang, Y.; Liu, T.; Han, H., Efficient hole-conductor-free, fully

printable mesoscopic perovskite solar cells with a broad light harvester NH2CH=NH2PbI3. J. Mater. Chem. A 2014, 2, 17115-17121. (44)

Elseman, A. M.; Rashad, M. M.; Hassan, A. M., Easily Attainable, Efficient Solar Cell

with Mass Yield of Nanorod Single-Crystalline Organo-Metal Halide Perovskite Based on a Ball Milling Technique. ACS Sustainable Chem. Eng. 2016, 4, 4875-4864. (45)

You, J.; Meng, L.; Song, T. B.; Guo, T. F.; Yang, Y.; Chang, W. H.; Hong, Z.; Chen, H.;

Zhou, H.; Chen, Q., Improved air stability of perovskite solar cells via solution-processed metal oxide transport layers. Nat. Nanotechnol. 2015, 11, 75-81. (46)

Docampo, P.; Ball, J. M.; Darwich, M.; Eperon, G. E.; Snaith, H. J., Efficient

organometaltrihalide perovskite planar-heterojunction solar cells on flexible polymer substrates. Nat. Commun. 2013, 4, DOI:10.1038/ncomms3761.


25


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

(47)

Page 26 of 35

Xu, X.; Liu, Z.; Zuo, Z.; Zhang, M.; Zhao, Z.; Shen, Y.; Zhou, H.; Chen, Q.; Yang, Y.;

Wang, M., Hole selective NiO contact for efficient perovskite solar cells with carbon electrode. Nano Lett. 2015, 15, 2402-2408. (48)

Zhu, H.; Li, W.; Wu, Y.; Liu, B.; Zhu, S.; Li, X.; Ågren, H.; Zhu, W., Insight into

Benzothiadiazole Acceptor in D–A−π–A Configuration on Photovoltaic Performances of DyeSensitized Solar Cells. ACS Sustainable Chem. Eng. 2014, 2, 1026-1034. (49)

Dai, P.; Dong, H.; Liang, M.; Cheng, H.; Sun, Z.; Xue, S., Understanding the Role of

Electron Donor in Truxene Dye Sensitized Solar Cells with Cobalt Electrolytes. ACS Sustainable Chem. Eng. 2017, 5 , 97-104. (50)

Li, H.; Cao, K.; Cui, J.; Liu, S.; Qiao, X.; Shen, Y.; Wang, M., 14.7% efficient

mesoscopic perovskite solar cells using single walled carbon nanotubes/carbon composite counter electrodes. Nanoscale 2015, 8, 6379-6385. (51)

Li, D.; Cui, J.; Li, H.; Huang, D.; Wang, M.; Shen, Y., Graphene oxide modified hole

transport layer for CH3NH3PbI3 planar heterojunction solar cells. Solar Energy 2016, 131, 176182. (52)

Ito, S.; Mizuta, G.; Kanaya, S.; Kanda, H.; Nishina, T.; Nakashima, S.; Fujisawa, H.;

Shimizu, M.; Haruyama, Y.; Nishino, H., Light stability tests of CH3NH3PbI3 perovskite solar cells using porous carbon counter electrodes. Phys. Chem. Chem. Phys. 2016, 18, 27102-27108. (53)

Peiris, T. A. N.; Baranwal, A. K.; Kanda, H.; Fukumoto, S.; Kanaya, S.; Bessho, T.;

Cojocaru, L.; Miyasaka, T.; Segawa, H.; Ito, S., Effect of Electrochemically Deposited MgO Coating on Printable Perovskite Solar Cell Performance. Coatings 2017, 7, 36-44. (54) Qin, X.J.; Zhao, Z.G.; Wang, Y.D.; Wu, J.B.; Jiang, Q; You, J.B., Recent progress in stability of perovskite solar cells. J. Semicond. 2017, 38, 011002


26

Page 27 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


For table of contents use only Fast drying boosted performance improvement of low-temperature paintable carbon-based perovskite solar cell Qian-Qian Chu, Bin Ding, Yan Li, Li-Li Gao, Qi Qiu, Cheng-Xin Li, Chang-Jiu Li, Guan-Jun Yang and Baizeng Fang

Synopsis: The low cost, energy and resource conservation-orientedand scalable low-temperature preparation process was utilized to improve photovoltaic performance largely.


27


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 1. (a) The well prepared carbon paste on FTO/TiO2/Perovskite, (b) The detailed structure of carbon paste on FTO/TiO2/Perovskite, (c) The long path created for solvent molecules and by conventional drying method in the drying process, in which the obstruction of carbon black and graphite to the movement of solvents in carbon paste increases the drying duration of carbon paste resulting in the serious damage of perovskite, and (d) The well retained perovskite film by fast drying which could reduce the drying time of carbon paste keeping the perovskite film well retained with little dissolution degradation. 105x73mm (300 x 300 DPI)


Page 28 of 35

Page 29 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Figure 2. Fabrication process of TiO2/perovskite/carbon solar cell with GPM. (a) Perovskite film coated on TiO2/FTO, (b) a wet carbon paste applied on the substrate, (c) carbon paste dried by a gas pump, and (d) the dried carbon paste on the substrate. 75x60mm (300 x 300 DPI)



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 3. (a) Drying rate of the carbon paste with and without GPM. (b) The resistance of CE in different thickness with and without GPM. 75x28mm (300 x 300 DPI)


Page 30 of 35

Page 31 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Figure 4. (a, d, g) Cross-sectional view of FTO/c-TiO2/m-TiO2/perovskite film, cross-sectional view of W/O GPM device, and W/ GPM device; (b, e, h) Magnified images of a, d, and g respectively; Thickness of perovskite film of (c) W/O CE device, (f) W/O GPM device, and (i) W/ GPM device. 150x113mm (300 x 300 DPI)



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 5. Current-voltage characteristics of (a) W/ GPM device, (b) W/O GPM device. (c) The corresponding output of PCE and current density at maximum power point of 0.74 V for the champion cell under a simulated AM 1.5G solar illumination of 100 mW/cm2. 150x36mm (300 x 300 DPI)


Page 32 of 35

Page 33 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Figure 6. (a) The PCE, (b) the open circuit voltage (Voc), (c) the short circuit current density (Jsc) and (d) the fill factor (FF) of the as-constructed 36 carbon based perovskite solar cells prepared by GPM. 75x54mm (300 x 300 DPI)



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 7. (a) Nyquist plots of the cell with and without GMP under the -0.9 V bias. (b) An enlarged view of Figure 7a. Nyquist plots of the cell (c) with GMP and (d) without GPM. (e) The RCE and (f) Rct of the cell with GMP and without GPM. 75x101mm (300 x 300 DPI)


Page 34 of 35

Page 35 of 35

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Figure 8. (a) The normalized PCE, (b) the normalized voltage, (c) the normalized current density, and (d) the normalized fill factor shown as a function of test time for the perovskite solar cells with the champion PCE and of W/ and W/O GPM devices. 75x57mm (300 x 300 DPI)


Fast Drying Boosted Performance Improvement of Low-Temperature

Recommend Documents