Group 4 Octahedral Benzamidinate Complexes ... - ACS Publications

Contribution from the Department of Chemistry and Institute of Catalysis ... Chemical Engineering, Technion, Israel Institute of Technology, Haifa 320...
0 downloads 0 Views 409KB Size
Published on Web 01/31/2003

Group 4 Octahedral Benzamidinate Complexes: Syntheses, Structures, and Catalytic Activities in the Polymerization of Propylene Modulated by Pressure Victoria Volkis,† Elza Nelkenbaum,† Anatoli Lisovskii,† Gil Hasson,† Rafi Semiat,‡ Moshe Kapon,† Mark Botoshansky,† Yoav Eishen,† and Moris S. Eisen*,† Contribution from the Department of Chemistry and Institute of Catalysis Science and Technology, Technion, Israel Institute of Technology, Haifa 32000, Israel, and Department of Chemical Engineering, Technion, Israel Institute of Technology, Haifa 32000, Israel Received April 22, 2002 ; E-mail: [email protected]

Abstract: The synthesis and structural X-ray diffraction studies for some benzamidinate ligations and several group 4 benzamidinate complexes are presented. The use of the cis-octahedral C2-symmetry compounds was studied to shed light on the conceptual applicability of these complexes as potential catalysts for the stereoregular polymerization of propylene. We demonstrate that the stereoregular polymerization of propylene catalyzed by early-transition metal octahedral benzamidinate complexes, activated with either MAO or B(C6F5)3 as cocatalysts, can be modulated by pressure (from atactic to isotactic through elastomers). The different effects in the polymerization process such as the nature of solvent or cocatalyst, temperature, pressure, molar ratio catalyst:cocatalyst, and the relationship between the symmetry of the complex and the polymer microstructure have been investigated. When the complex [4-CH3-C6H4C(NTMS)2]2ZrMe2 (9) was activated with MAO, it was found to be a good catalyst for the polymerization of propylene, at atmospheric pressure, producing an oily polymer resembling an atactic polypropylene. Being activated with B(C6F5)3, complex 9 produces a highly isotactic (mmmm ) 98%) product. Likewise, when the polymerization of propylene was performed with complex 9 and MAO at high pressure (liquid propylene), a highly stereoregular polymer was also obtained. Larger activities and stereoregularities were achieved by performing the reaction in CH2Cl2 as compared to toluene. Contrary to complex 9, at atmospheric pressure the complex [4-CH3-C6H4C(NTMS)2]2TiMe2 (10) is not active either in CH2Cl2 or in toluene. At high pressure, complex 10 produces elastomeric polypropylene. Activities of the isolobal complexes [C6H4C(NTMS)2]2ZrMe2 (11) and [C6H4C(NTMS)2]2TiMe2 (12) were found to be larger than those of complexes 9 and 10, respectively. Contrary to the structures of the elastomeric polypropylenes described in the literature, the obtained elastomers are characterized by frequent alternation of the isotactic domains with stereodefects. The stereoregular errors are formed by the intramolecular epimerization of the growing chain at the last inserted unit. The epimerization reaction was corroborated through the isomerization of alkenes.

Introduction

Metal-mediated olefin polymerization catalysts have experienced a vast growth since the pioneering work of Ziegler and Natta, which showed that systems such as TiCl4/AlClEt2 catalyze the polymerization of ethylene to high-density polyethylene and propylene to stereoregular polypropylene.1 Successful application of the Ziegler-Natta catalysts has stimulated intense academic and industrial research activity focused on understanding the relationships between the structure, activity, selectivity of the catalysts, and the properties of the obtained polymers. † Department of Chemistry and Institute of Catalysis Science and Technology, Technion. ‡ Department of Chemical Engineering, Technion.

(1) (a) Ziegler, K.; Holzkamp, H.; Breil, H.; Martin, H. Angew. Chem., Int Ed. Engl. 1955, 67, 54. (b) Natta, G. Angew. Chem., Int. Ed. Engl. 1956, 68, 393. (c) Catalytic Olefin Polymerization; Keii, T., Soga, K., Eds.; Elsevier: Amsterdam, 1990. (d) Fink, G.; Mu¨lhaupt, R.; Brintzinger, H. H. Ziegler Catalysis; Springer-Verlag: Heidelberg, 1994. (e) Transition Metals and Organometallics as Catalysts for Olefin Polymerization; Kaminsky, W., Sinn, H., Eds.; Springer-Verlag: Berlin, 1987 and references therein. 10.1021/ja020575r CCC: $25.00 © 2003 American Chemical Society

These studies resulted in the discovery of metallocenes as a new Ziegler-Natta type of homogeneous “single-site” catalysts for the polymerization of R-olefins.2,3 These metallocenes being activated with either methylalumoxane (MAO) or perfluorinated boron cocatalysts provide high activities, high stereoregularities, narrow polydispersities of the polymers, and control over the (2) (a) Kaminsky, W. Olefin Polymerization Catalyzed by Metallocenes. In AdVances in Catalysis; Gates, B. C., Kno¨zinger, H., Eds.; Academic Press: San Diego, 2002; Vol. 46, p 89. (b) Marks, T. J., Stevens, J. C., Eds. Topics in Catalysis; Baltzer: Basel, Switzerland, 1999; Vol. 15 and references therein. (c) Mu¨lhaupt, R. In Polypropylene: An A-Z Reference; Karger-Kocsis, J., Ed.; Kluwer Academic Publisher: Dordrecht, 1999; p 454. (d) Kaminsky, W.; Arndt, M. AdV. Polym. Sci. 1997, 127, 143 and references therein. (e) Bochmann, M. J. Chem. Soc., Dalton Trans. 1996, 255 and references therein. (f) Brintzinger, H. H.; Fisher, D.; Mu¨lhaupt, R.; Rieger, B.; Waymouth, R. M. Angew. Chem., Int. Ed. Engl. 1995, 34, 1143 and references therein. (3) (a) Alt, H. G.; Ko¨pll, A. Chem. ReV. 2000, 100, 1205 and references therein. (b) Coates, G. W. Chem. ReV. 2000, 100, 1223 and references therein. (c) Resconi, L.; Cavallo, L.; Fait, A.; Piemontesi, F. Chem. ReV. 2000, 100, 1253. (d) Alt, H. G. J. Chem. Soc., Dalton Trans. 1999, 1703 and references therein. (e) Kaminsky, W. J. Chem. Soc., Dalton Trans. 1998, 1413. J. AM. CHEM. SOC. 2003, 125, 2179-2194

9

2179

ARTICLES

Volkis et al.

polymeric architecture.2-4 In addition, comonomer incorporation and long chain branching can be modulated to a significant extent by suitable adjustment of both catalyst and cocatalyst structures’ design.5 In general, these catalytic systems, as represented by A, contain many required motifs for an active polymerization catalyst, including a suitable spectator ancillary ligation (Ln), an electron-deficient and coordinatively unsaturated metal center (M), an effective weekly coordinative counteranion/cocatalyst (X-), and the appropriate temperature, solvent, and pressure conditions.

The majority of the catalysts belong to groups 3 and 4 metallocene derivatives, although some are know to contain one cyclopentadienyl ring and one pendant ligand.6 The tacticity of the polymers varies predictably with the structure of the metallocenes. Hence, C2- or C1-symmetry complexes are expected to produce isotactic poly R-olefins, whereas C2V induces the formation of atactic polymers.7 Because in the polymerization of R-olefins the ligation around the metal center is crucial in determining the activity and stereospecificity of the catalysts, affecting both electronic and steric properties, a growing interest in the development of noncyclopentadienyl ligations has been stimulated.8 (4) (a) Chen, E. Y.-X.; Marks, T. J. Chem. ReV. 2000, 100, 1391. (b) Metz, M. V.; Schwartz, D. J.; Stem, C. L.; Nickias, P. N.; Marks, T. J. Angew. Chem., Int. Ed. 2000, 39, 1312. (c) Beswick, C. L.; Marks, T. J. J. Am. Chem. Soc. 2000, 122, 10358 and references therein. (d) Lanza, G.; Fragala`, I. L.; Marks, T. J. J. Am. Chem. Soc. 2000, 122, 12764 and references therein. (e) Beswick, C. L.; Marks, T. J. Organometallics 1999, 18, 10358, 2410. (f) Williams, V. C.; Piers, W. E.; Clegg, W.; Elsegood, M. R. J.; Collins, S.; Marder, T. B. J. Am. Chem. Soc. 1999, 121, 3244. (g) Deck, P. A.; Beswick, C. L.; Marks, T. J. J. Am. Chem. Soc. 1998, 120, 1772. (h) Chen, Y.-X.; Metz, M. V.; Li, L.; Stern, C. L.; Marks, T. J. J. Am. Chem. Soc. 1998, 120, 6287. (i) Li, L.; Marks, T. J. Organometallics 1998, 17, 3996. (j) Piers, W. E.; Chivers, T. Chem. Soc. ReV. 1997, 26, 345. (k) Temme, B.; Erker, G.; Karl, J.; Luftmann, H.; Frohlich, R.; Kotila, S. Angew. Chem., Int. Ed. Engl. 1995, 34, 1755. (5) (a) Fan, W.; Leclerc, M. K.; Waymouth, R. M. J. Am. Chem. Soc. 2001, 123, 9555. (b) Kim, J. S.; Wojcinski, L. M., II; Liu, S.; Sworen, J. C.; Sen, A. J. Am. Chem. Soc. 2000, 122, 5668. (c) Leclerc, M. K.; Waymouth, R. M. Angew. Chem., Int. Ed. 1998, 37, 922. (d) Jin, J. H.; Uozumi, T.; Sano, T.; Teranishi, T.; Soga, K.; Shiono, T. Macromol. Rapid Commun. 1998, 19, 337. (e) Arndt, N.; Kaminsky, W.; Schauwienold, A. M.; Weingarten, U. Macromol. Chem. Phys. 1998, 199, 1135. (f) Uozumi, T.; Myyazawa, K.; Sano, T.; Soga, K. Macromol. Rapid Commun. 1997, 18, 883. (6) (a) Brown, S. J.; Gao, X.; Harrison, D. G.; Koch, L.; Spence, R. E. H.; Yap, G. P. A. Organometallics 1998, 17, 5445. (b) McKnight, A. L.; Massod, M. A.; Waymouth, R. M.; Straus, D. A. Organometallics 1997, 16, 2879. (c) Chen, Y.-X.; Marks, T. J. Organometallics 1997, 16, 3649. (d) Jia, L.; Yang, X.; Stern, C. L.; Marks, T. J. Organometallics 1997, 16, 842. (e) Chen, Y. X.; Fu, P. F.; Stern, C. L.; Marks, T. J. Organometallics 1997, 16, 5958. (f) Chen, Y.-X.; Stern, C. L.; Yang, S.; Marks, T. J. J. Am. Chem. Soc. 1996, 118, 12451. (g) Hightower, J. W., Delglass, W. N., Iglesia, E., Bell, A. T., Eds.; Studies in Surface Science and Catalysis; Elsevier: Amsterdam, 1996; Vol. 101, pp 1-729. (h) Tetsunosuke, S.; Tadashi, A.; Norihide, I. Makromol. Rapid Commun. 1996, 17, 9. (i) Ribeiro, M. R.; Deffleux, A.; Portella, M. F. Ind. Eng. Chem. Res. 1997, 36, 1224. (j) Galan-Fereres, M.; Koch, T.; Hey-Hawkins, E.; Eisen, M. S. J. Organomet. Chem. 1999, 580, 145. (k) Shapiro, P. J.; Brunel, E.; Schaefer, W. P.; Bercaw, J. E. Organometallics 1990, 9, 867. (l) Shapiro, P. J.; Cotter, W. D.; Schaefer, W. P.; Labinger, J. A.; Bercaw, J. E. J. Am. Chem. Soc. 1994, 16, 4623. (m) Carpenetti, D. W.; Kloppenburg, L.; Kupec, J. T.; Petersen, J. L. Organometallics 1996, 15, 255. (7) (a) Averbuj, C.; Tish, E.; Eisen, M. S. J. Am. Chem. Soc. 1998, 120, 8640. (b) Ewen, J. A.; Jones, R. L.; Razavi, A.; Ferrara, J. D. J. Am. Chem. Soc. 1988, 110, 6255. (c) Catalyst Design for Tailor-Made Polyolefins; Soga, K., Terrano, M., Eds.; Elsevier: Tokyo, 1994. (d) Mo¨hring, P. C.; Coville, N. J. J. Organomet. Chem. 1994, 479, 1. (e) Ewen, J. A. J. Am. Chem. Soc. 1984, 106, 6355. 2180 J. AM. CHEM. SOC.

9

VOL. 125, NO. 8, 2003

A tremendous effort has been made in designing new complexes with different ancillary ligations of the metals of groups 3-13 as suitable precursors for the polymerization of R-olefins.8 The wide variety of carbon-,9 oxygen-,10 and nitrogen-based ligands11,12 has been described. Most attention has been directed to chelating di(amido) ligands,13 some of whose group 4 transition metal complexes induce the living polymerization of R-olefins.14 Recently, chelating alkoxo,15 boratabenzene,16 chelating salicilaldiminato,15,17 acetylacetonate,18 phosphinoamines,19 and chelating amidinate20 compounds have received attention as ancillary ligands in the synthesis of potential Ziegler-Natta catalysts. Within the amidinate-based ligands, a variety of benzamidinate group 4-containing complexes have been described. These (8) (a) Ittel, S. D.; Johnson, L. K.; Brookhardt, M. Chem. ReV. 2000, 100, 1169. (b) Britovsek, G. J. P.; Gibson, V. C.; Wass, D. F. Angew. Chem., Int. Ed. 1999, 38, 428 and references therein. (9) (a) Bochmann, M.; Lancaster, S. J. Organometallics 1993, 12, 663. (b) Pellecchia, C.; Grassi, A.; Immirzi, A. J. Am. Chem. Soc. 1993, 115, 1160. (c) Ewart, S. W.; Sarsfield, M. J.; Jeremic, D.; Tremblay, T. L.; Williams, E. F.; Baird, M. C. Organometallics 1998, 17, 1502. (d) Pellecchia, C.; Immirzi, A.; Grassi, A.; Zambelli, A. Organometallics 1993, 12, 4473. (10) (a) Shrock, R. R.; Baumann, R.; Reid, S. M.; Goodman, J. T.; Stumpf, R.; Davis, W. M. Organometallics 1999, 18, 3649. (b) Mack, H.; Eisen, M. S. J. Chem. Soc., Dalton Trans. 1998, 917. (c) Gielens, E. E. C. G.; Tiesnitsch, J. Y.; Hessen, B.; Teuben, J. H. Organometallics 1998, 17, 1652. (d) Chen, Y.-X.; Fu, P.-F.; Stern, C. L.; Marks, T. J. Organometallics 1997, 16, 5958. (e) Sernetz, F. G.; Mu¨lhaupt, R.; Fokken, S.; Okuda, J. Macromolecules 1997, 30, 1562. (f) Bei, X.; Swenson, D. C.; Jordan, R. F. Organometallics 1997, 16, 3282. (11) (a) Kempe, R. Angew. Chem., Int. Ed. 2000, 39, 468 and references therein. (b) Gade, L. H. Chem. Commun. 2000, 173. (12) (a) Goodman, J. T.; Schrock, R. R. Organometallics 2001, 20, 5205. (b) Schrock, R. R.; Bonitatebus, P. J., Jr.; Schrodi, Y. Organometallics 2001, 20, 1056. (c) O’Connor, P. E.; Morrison, D. J.; Steeves, S.; Burrage, K.; Berg, D. J. Organometallics 2001, 20, 1153. (d) Yoshida, Y.; Matsui, S.; Takagi, Y.; Mitani, M.; Nakano, T.; Tanaka, H.; Kashiwa, N.; Fujita, T. Organometallics 2001, 20, 4793. (e) Danie`le, S.; Hitchcock, P. B.; Lappert, M. F.; Merle, P. G. J. Chem. Soc., Dalton Trans. 2001, 13. (f) Mehrkhodavandi, P.; Bonitatebus, P. J., Jr.; Schrock, R. R. J. Am. Chem. Soc. 2000, 122, 7841. (g) Skinner, M. E. G.; Cowhig, D. A.; Mountford, P. Chem. Commun. 2000, 1167. (h) Nomura, K.; Oya, K.; Imanishi, Y. Polymer 2000, 41, 2755. (i) Lee, C. H.; La, Y.-H.; Park, J. W. Organometallics 2000, 19, 344 and references therein. (13) (a) Ziniuk, Z.; Goldberg, I.; Kol, M. Inorg. Chem. Commun. 1999, 2, 549. (b) Liang, L.-C.; Schrock, R. R.; Davis, W. M.; McConville, D. H. J. Am. Chem. Soc. 1999, 121, 5797. (c) Graf, D. D.; Schrock, R. R.; Davis, W. M.; Stumpf, R. Organometallics 1999, 18, 843. (d) Schrock, R. R.; Baumann, R.; Reid, S. M.; Goodman, J. T.; Stumpf, R.; Davis, W. M. Organometallics 1999, 18, 3649. (e) Gue´rin, F.; McConville, D. H.; Vittal, J. J.; Yap, G. A. P. Organometallics 1998, 17, 5172. (f) Gibson, V. C.; Kimberley, V. S.; White, A. J. P.; Williams, D. J.; Howard, P. Chem. Commun. 1998, 313. (g) Scollard, J. D.; McConville, D. H.; Vittal, J. J. Organometallics 1997, 16, 4415. (h) Mack, H.; Eisen, M. S. J. Organomet. Chem. 1996, 525, 81. (14) (a) Tshuva, E. Y.; Goldberg, I.; Kol, M.; Goldschmidt, Z. Organometallics 2001, 20, 3017. (b) Tshuva, E. Y.; Goldberg, I.; Kol, M. J. Am. Chem. Soc. 2000, 122, 10706. (c) Baumann, R.; Davis, W. M.; Schrock, R. R. J. Am. Chem. Soc. 1997, 119, 3830. (d) Scollard, J. D.; McConville, D. H. J. Am. Chem. Soc. 1996, 118, 10008 and references therein. (15) (a) Matsui, S.; Mitani, M.; Saito, J.; Tohi, Y.; Makio, H.; Matsukawa, N.; Takagi, Y.; Tsuru, K.; Nitabaru, M.; Nakano, T.; Tanaka, H.; Kashiwa, N.; Fujita, T. J. Am. Chem. Soc. 2001, 123, 6847. (b) Matsukawa, N.; Matsui, S.; Mitani, M.; Saito, J.; Tsuru, K.; Fujita, T. J. Mol. Catal. A: Chem. 2001, 169, 99. (c) Saito, J.; Mitani, M.; Mohri, J.; Yoshida, Y.; Matsui, S.; Ishii, S.; Kojoh, S.; Kashiwa, N.; Fujita, T. Angew. Chem., Int. Ed. 2001, 40, 2918. (d) Sobota, P.; Przybylak, K.; Urko, J.; Jerzykiewicz, L. B.; Pombiero, A. J. L.; da Silva, M. F. C. G.; Szczegot, K. Chem.-Eur. J. 2001, 7, 951. (e) Nakayama, Y.; Watanabe, K.; Ueyama, N.; Nakamura, A.; Harada, A.; Okuda, J. Organometallics 2000, 19, 2498. (f) Okuda, J.; Fokken, S.; Kleinhenn, T.; Spaniol, T. P. Eur. J. Inorg. Chem. 2000, 1321. (16) (a) Pellecchia, C.; Proto, A.; Longo, P.; Zambelli, A. Macromol. Chem. Rapid Commun. 1991, 12, 663. (b) Pellecchia, C.; Proto, A.; Longo, P.; Zambelli, A. Macromol. Chem. Rapid Commun. 1992, 13, 277. (17) (a) Tian, J.; Hustad, P. D.; Coates, G. W. J. Am. Chem. Soc. 2001, 123, 5134. (b) Tian, J.; Coates, G. W. Angew. Chem., Int. Ed. 2000, 39, 3626. (c) Mitani, M.; Furuyama, R.; Mohri, J.; Saito, J.; Ishii, S.; Terao, H.; Kashiwa, N.; Fujita, T. J. Am. Chem. Soc. 2002, 124, 7888. (d) Saito, J.; Mitani, M.; Mohri, J..; Ishii, S.; Yoshida, Y.; Matsugi, T.; Kojoh, S.; Kashiwa, N.; Fujita, T. Chem. Lett. 2001, 567. (18) Shmulinson, M.; Galan-Fereres, M.; Lisovskii, A.; Nelkenbaum, E.; Semiat, R.; Eisen, M. S. Organometallics 2000, 19, 1208. (19) Koch, T.; Blaurock, S.; Hey-Hawkins, E.; Galan-Fereres, M.; Plat, D.; Eisen, M. S. J. Organomet. Chem. 2000, 595, 126.

Group 4 Octahedral Benzamidinate Complexes

systems are in principle devoted mainly to the use of N,N′-bis(trimethylsilyl)benzamidinate ligation. The benzamidinate ligands can be considered as a steric equivalent of Cp or Cp* (Cp ) C5H5; Cp* ) C5Me5), although they are unique in their electronic properties.20,21 The anionic moiety [R-C(NSiMe3)2]is a four-electron donor, promoting a higher electrophilicity at the metal center, as compared to the six electrons of the cyclopentadienyl ligands. The possibility to simply modify both steric bulk and electronic properties of the benzamidinate-based ligands, through changes in either the organic substituents at the nitrogen atom and/or different functional groups at the aromatic ring, makes these ligands very attractive for synthesis of various organometallic complexes and their corresponding utilization as catalytic precursors in the polymerization of R-olefins. Previously, others and we have investigated the polymerization of R-olefins catalyzed by several group 4 chelating benzamidinate complexes.22 The bis(benzamidinate) dichloride/ dialkyl group 4 complexes are normally obtained as a mixture of racemic C2-symmetry cis-octahedral structures, and, when activated with methylalumoxane (MAO), these complexes were found to be active catalytic precursors for the polymerization of ethylene, propylene, the oligomerization of 1,5-hexadiene, and the isomerization of internal and terminal olefins.7a,22 For propylene, performing the polymerization at atmospheric pressure produced polypropylene as an oil, despite the expected isotactic polymer.23 These results raise conceptual questions regarding the applicability of cis-octahedral C2-symmetry complexes to the stereospecific polymerization of R-olefins. Here, we present the synthesis and structural X-ray diffraction studies on several group 4 benzamidinate complexes. We introduce the application of these complexes as new catalytic precursors for the highly stereoregular polymerization of propylene, which can be modulated by pressure. To our knowledge, this is the first example of stereoregular polymerization of R-olefins catalyzed by early-transition metal octahedral complexes, modulated by pressure (from atactic to isotactic through elastomers). We present a thorough study disclosing the different effects, such as pressure, temperature, and nature of solvents in the polymerization process and in the properties of the polymers (20) (a) Jayaratne, K. C.; Sita, L. R. J. Am. Chem. Soc. 2001, 123, 10754. (b) Keaton, R. J.; Jayaratne, K. C.; Henningsen, D. A.; Koterwas, L. A.; Sita, L. R. J. Am. Chem. Soc. 2001, 123, 6197. (c) Jayaratne, K. C.; Sita, L. R. J. Am. Chem. Soc. 2000, 122, 958. (d) Littke, A.; Sleiman, N.; Bensimon, C.; Richeson, D. S.; Yap, G. P. A.; Brown, S. J. Organometallics 1998, 17, 446. (e) Gomez, R.; Duchateau, R.; Chernega, A. N.; Teuben, J. N.; Edelmann, F. T.; Green, M. L. H. J. Organomet. Chem. 1995, 491, 153. (21) (a) Hagadorn, J. R.; Arnold, J. Organometallics 1998, 17, 1355. (b) Hagadorn, J. R.; Arnold, J. J. Chem. Soc., Dalton Trans. 1997, 3087. (c) Hagadorn, J. R.; Arnold, J. J. Am. Chem. Soc. 1996, 118, 893. (d) Edelmann, F. T. Coord. Chem. ReV. 1994, 137, 403 and references therein. (e) Edelmann, F. T. Top. Curr. Chem. 1996, 179, 113 and references therein. (f) Hagadorn, J. R.; Arnold, J. Organometallics 1994, 13, 4670. (22) (a) Richter, J.; Edelmann, F. T.; Noltemeyer, M.; Schmidt, H.-G.; Shmulinson, M.; Eisen, M. S. J. Mol. Catal. 1998, 130, 149. (b) Walter, D.; Fischer, R.; Friedrich, F.; Gebhardt, P.; Go¨rls, H. Chem. Ber. 1996, 129, 1389. (c) Walter, D.; Fischer, R.; Go¨rls, H.; Koch, J.; Scheweder, B. J. J. Organomet. Chem. 1996, 508, 13. (d) Duchateau, R.; van Wee, C. T.; Meetsma, A.; van Duijnen, P. T.; Teuben, J. H. Organometallics 1996, 15, 2279. (e) Gomez, R.; Green, M. L. H.; Haggitt, J. L. J. Chem. Soc., Dalton Trans. 1996, 939. (f) Flores, J. C.; Chien, J. C. W.; Rausch, M. D. Organometallics 1995, 14, 1827. (g) Flores, J. C.; Chien, J. C. W.; Rausch, M. D. Organometallics 1995, 14, 2106. (h) Herscovics-Korine, D.; Eisen, M. S. J. Organomet. Chem. 1995, 503, 307. (i) Gomez, R.; Duchateau, R.; Chernega, A. N.; Meetsma, A.; Edelmann, F. T.; Teuben, J. H.; Green, M. L. H. J. Chem. Soc., Dalton Trans. 1995, 217. (j) Gomez, R.; Green, M. L. H.; Haggitt, J. L. J. Chem. Soc., Chem. Commun. 1994, 2607. (23) For a preliminary result, see: Volkis, V.; Shmulinson, M.; Averbuj, C.; Lisovskii, A.; Edelmann, F. T.; Eisen, M. S. Organometallics 1998, 17, 3155.

ARTICLES

obtained. Moreover, we introduce a new type of elastomeric polypropylene that is facile to design and to tailor. The mechanism for the formation of the various types of polypropylene (atactic, isotactic, and elastomeric) at the different conditions is discussed. Results and Discussion

The goal of this investigation was to examine the scope, relationship between symmetry of the complex and polymer microstructure, stereoregularity, metal sensitivity, monomer concentration, substituent effect at the ancillary ligation, temperature, solvent, cocatalyst, polymerization time, and to propose a plausible mechanism for the polymerization of propylene promoted by racemic mixtures of cis-octahedral complexes. This study represents an extension of the unique reactivities of this type of complex in the polymerization of propylene, when activated by either MAO or perfluoroaryl borane cocatalysts. In the following presentation of the results, we focus on the synthesis of the ligands and group 4 metal complexes, and on the different parameters affecting the polymerization of propylene toward the formation of either atactic, isotactic, or elastomeric polymers. We report the X-ray single-crystal diffraction studies for the benzamidinate ligands and the corresponding group 4 complexes. In addition, we present evidence, through the isomerization of alkenes, for the epimerization of the last inserted monomer as the major mechanistic pathway, responsible for the formation of polypropylene with elastomeric properties. We start the presentation of the results with various synthetic pathways of different ancillary benzamidinate ligations followed by the synthesis and characterization of the corresponding group 4 complexes. Synthesis of Benzamidinate Ligands. The preparation of the lithium benzamidinate was carried out through the reaction between benzonitrile (or p-tolunitrile) and the lithium salt LiN(SiMe3)2.24

In the absence of a strong coordinating polar solvent, the dimeric structures 1 or 2 are the major products obtained (eq 1), in addition to some trimeric species, although when the reaction is carried out in the presence of TMEDA (tetramethylethylenediamine), as the coordinated solvent, the monomeric (24) (a) Wedler, M.; Kno¨sel, F.; Noltemeyer, M., Edelmann, F. T. J. Organomet. Chem. 1990, 388, 21. (b) Stalke, D.; Wedler, M.; Edelmann, F. T. J. Organomet. Chem. 1992, 431, C1. (c) Edelmann, F. T. J. Organomet. Chem. 1992, 426, 295. (d) Dick, D. G.; Duchateau, R.; Edema, J. H.; Gambarotta, S. Inorg. Chem. 1993, 32, 1959. (e) Barker, J.; Barr, D.; Barnett, N. D. R.; Clegg, W.; Cragg-Hine, I.; Davidson, M. G.; Davies, R. P.; Hodson, S. M.; Howard, J. A. K.; Kilner, M.; Lehmann, C. W.; Lopez-Solera, I.; Mulwey, R. E.; Raithby, P. R.; Snaith, R. J. Chem. Soc., Dalton Trans. 1997, 95. J. AM. CHEM. SOC.

9

VOL. 125, NO. 8, 2003 2181

ARTICLES

Volkis et al.

complexes [R-PhC(NSiMe3)2Li(TMEDA)] (R ) CH3 (3); H (4)) are obtained as the sole products (eq 2).

The low-temperature X-ray analysis of 2 (Figure 1, Tables 1 and 10) shows a dimeric benzamidinate structure with two distorted-tetrahedral lithium cations. Each lithium atom is π-bonded by one bidentate benzamidinate moiety, σ-bonded to the second benzamidinate nitrogen atom, and σ-bonded to a nitrogen of a benzonitrile molecule. The core units are comprised by a four-membered ring Li-N-C-N and a six-membered ring Li-N-C-N-Li-N. The planes formed by the two η3diazaallyl motifs make a dihedral angle of almost 90°, forming a distorted C2V-symmetry complex. The four C-N bond lengths in both amidinates are close to the average of the CdN [1.30 Å] and C-N [1.36 Å] bond lengths, as compared to similar protonated N-substituted phenyl ligands.25 This result suggests that the anion in complex 2 is best described as a system containing two diazaallyl moieties, one of which acts as a double bridge of two lithium atoms. The molecular structure of complex 4 (Figure 2, Tables 2, 10) shows a slightly distorted tetrahedral monomeric lithium atom (angle between the two planes containing the metal ) 93.3 (4)°) attached in an almost symmetrical mode to both amidine and TMEDA moieties [Li-N(5) ) 2.033 (6), Li-N(13) ) 2.019 (6), Li-N(18) ) 2.120 (6), Li-N(23) ) 2.116 (7) Å]. The similar electronic delocalization throughout the amidine moiety is observed by the similar C-N distances [N(5)-C(6) ) 1.331 (4), C(6)-N(13) ) 1.325 (4) Å]. Interestingly, there is almost no electronic interaction between the aromatic phenyl ring and the diazaalyl section as exhibited by the torsional angle (94.2°). Synthesis of Zr and Ti Bis(benzamidinate) Complexes. The reaction of MCl4 (M ) Zr, Ti) with 2 equiv of the appropriate ligands 3 and 4 takes place at room temperature in toluene to give pale yellow (Zr) and brown-red (Ti) solutions, from which analytically pure compounds 5-8 were isolated. For the zirconium complexes, high yields (88-89%) are achieved, whereas for the corresponding titanium complexes, lower yields are obtained (60-70%). The solid X-ray characterization of complexes 721b,22d,i and 826 has been already reported. It is noteworthy that complexes 7 and 8 can be also attained by the reaction of the MCl4 (M ) Zr, Ti) and 1 equiv of the corresponding benzamidinate lithium dimer 2, whereas com(25) For a comparison to a similar isostructural complex and to various lithium benzamidinate complexes, see: (a) Eisen, M. S.; Kapon, M. J. Chem. Soc., Dalton Trans. 1994, 3507. (b) Lisovskii, A.; Botoshansky, M.; Eisen, M. S. J. Chem. Soc., Dalton Trans. 2001, 1692 and references therein, and ref 24. (26) Roesky, H. W.; Meller, B.; Noltemeyer, M.; Schmidt, H.-G.; Scholz, U.; Sheldrick, G. M. Chem. Ber. 1988, 121, 1403. 2182 J. AM. CHEM. SOC.

9

VOL. 125, NO. 8, 2003

Figure 1. ORTEP diagram (50% probability ellipsoid) of complex 2. Table 1. Selected Bond Lengths [Å] and Angles [deg] for Complex 2

Li(1)-N(13) Li(1)-N(35) Li(1)-N(22) Li(1)-N(30) Li(1)-C(23) Li(1)-Li(2) Li(2)-N(5) Li(2)-N(30) Li(2)-N(43) Li(2)-N(22) Li(2)-C(23) N(13)-Li(1)-N(35) N(13)-Li(1)-N(22) N(35)-Li(1)-N(22) N(13)-Li(1)-N(30) N(35)-Li(1)-N(30) N(22)-Li(1)-N(30) N(5)-Li(2)-N(30) N(5)-Li(2)-N(43) N(30)-Li(2)-N(43) N(5)-Li(2)-N(22) N(30)-Li(2)-N(22) N(43)-Li(2)-N(22)

2.055(4) 2.086(4) 2.104(4) 2.126(4) 2.392(4) 2.465(5) 1.995(4) 2.069(4) 2.088(4) 2.364(4) 2.408(4) 118.53(18) 122.39(19) 111.28(18) 121.56(18) 106.25(17) 64.88(11) 116.67(18) 120.7(2) 110.84(17) 140.8(2) 61.16(11) 92.61(15)

plexes 5 and 6 can be prepared in lower yields, when they are formed using the corresponding dimer 1. Alkylation of complexes 5-8 with 2 equiv of MeLi‚LiBr in ether yields yellow dimethyl complexes of zirconium (9 and 11) or wine-red dimethyl complexes of titanium (10 and 12) in quantitative yields (98-99%) (eq 3). The crystalline structures of complexes 1121b,22d and 1227 have been reported in the literature. The crystallographic data for complexes 9 and 10 are given in Table 10. Selected bond lengths and angles are listed in Tables 3 and 4, and their molecular structures are shown in Figures 3 and 4, respectively. The lowtemperature X-ray analysis of complex 9 shows that the central Zr atom is octahedral-bonded to two benzamidinate ligands and two terminal methyl groups. The octahedral complex is formed (27) Thiele, K.-H.; Windisch, H.; Windisch, H.; Edelmann, F. T.; Kilimann, U.; Noltemeyer, M. Z. Anorg. Allg. Chem. 1996, 622, 713.

Group 4 Octahedral Benzamidinate Complexes

ARTICLES Table 3. Selected Bond Lengths [Å] and Angles [deg] for Complex 9

Zr(1)-N(1) Zr(1)-C(1) Zr(1)-N(4) Zr(1)-C(11) Zr(1)-N(3) Zr(1)-C(2) Zr(1)-N(2) Zr(1)-C(3)

Figure 2. ORTEP diagram (50% probability ellipsoid) of complex 4. Table 2. Selected Bond Lengths [Å] and Angles [deg] for Complex 4

Li-N(13) Li-N(5) Li-N(23) Li-N(18) N(5)-C(6) C(6)-N(13) N(13)-Li-N(5) N(13)-Li-N(23) N(5)-Li-N(23) N(13)-Li-N(18) N(5)-Li-N(18) N(23)-Li-N(18)

2.019(6) 2.033(6) 2.116(7) 2.120(6) 1.331(5) 1.325(4) 69.14(19) 119.6(3) 122.5(3) 136.1(3) 128.6(3) 86.4(2)

in such a way that one carbon atom from the methyl groups (C(1)) and one nitrogen atom from the chelating benzamidinate

unit (N(4)) are in the axial positions, similarly as in complex 10, producing a C2-symmetric complex. The two four-membered

2.227(4) 2.246(5) 2.295(4) 2.672(5) 2.234(4) 2.248(6) 2.320(4) 2.578(5)

N(1)-Zr(1)-N(3) N(1)-Zr(1)-N(4) N(1)-Zr(1)-N(2) N(4)-Zr(1)-N(2) N(3)-Zr(1)-C(1) N(1)-Zr(1)-C(1) N(1)-Zr(1)-C(2) N(3)-Zr(1)-C(2) C(1)-Zr(1)-N(4) C(1)-Zr(1)-C(2) N(3)-Zr(1)-N(4) C(2)-Zr(1)-N(4) N(3)-Zr(1)-N(2) C(2)-Zr(1)-N(2)

91.1(2) 122.3(2) 59.34(14) 172.23(14) 97.4(3) 144.5(2) 91.3(2) 143.2(2) 143.2(2) 101.8(3) 59.3(2) 89.0(2) 113.93(14) 98.7(2)

Table 4. Selected Bond Lengths [Å] and Angles [deg] for Complex 10

Ti-N(14) Ti-C(19) Ti-N(5) Ti-C(6) N(5)-C(6) C(6)-N(14)

2.124(2) 2.120(4) 2.137(2) 2.515(3) 1.321(3) 1.321(3)

N(14)-Ti-N(14)#1 N(14)-Ti-C(19)#1 N(14)-Ti-C(19) C(19)#1-Ti-C(19) N(14)-Ti-N(5)#1 N(14)#1-Ti-N(5)#1 C(19)#1-Ti-N(5)#1 C(19)-Ti-N(5)#1 N(14)-Ti-N(5) N(5)#1-Ti-N(5)

94.88(12) 91.75(17) 153.16(13) 94.0(3) 108.32(8) 63.17(8) 90.06(12) 97.89(13) 63.17(8) 168.37(12)

rings ZrCN2 are almost symmetric: the C-N and Zr-N bond lengths are respectively equal (N(2)-C(11) ) 1.345 (6), N(1)C(11) ) 1.325 (6), N(3)-C(3) ) 1.336 (6), N(4)-C(3) ) 1.322 (6), Zr-N(1) ) 2.227 (4), Zr-N(2) ) 2.320 (4), Zr-N(3) ) 2.234 (4), Zr-N(4) ) 2.295 (4) Å). By comparison to other benzamidinate complexes, the Zr-N(1) to Zr-N(4) distances are somewhat longer than those in the dimeric compound [C6H5C(NSiMe3)2ZrCl3]2 (2.14 and 2.19 Å),28 while they are similar to those in the monomeric complexes [C6H5C(NSiMe3)2ZrCl2] (2.20 and 2.24 Å)21b,22d,i and [C6H5C(NSiMe3)2ZrMe2] (2.24 and 2.31 Å).21b,22d The benzamidinate moieties are located almost in one plane with the ZrCN2 units, with the corresponding angles Zr-C(3)-C(4) and Zr-C(11)-C(12) of 168.7 (3) and 170.6 (4)°, respectively. The X-ray study of the dimethyl titanium bis(benzamidinate) complex (10) shows that the Ti atom is octahedrally distorted surrounded by two chelating benzamidinate ligands and two terminal methyl groups. The methyl carbon atom (C(19)) and the nitrogen atom (N(14)) are in the axial positions [C(19)Ti-N(14) ) 153.16 (13)°], while the second methyl group and the remaining nitrogen atoms occupy the equatorial position [C(19)-Ti-N(14)# ) 91.75 (17), C(19)-Ti-N(5) ) 90.06 (28) Fenske, D.; Hartmann, E.; Dehnicke, K. Z. Naturforsch. 1988, 43b,1611. J. AM. CHEM. SOC.

9

VOL. 125, NO. 8, 2003 2183

ARTICLES

Volkis et al.

Figure 3. ORTEP diagram (50% probability ellipsoid) of complex 9.

Figure 5. ORTEP diagram (50% probability ellipsoid) of complexes 10* (a) and 13 (b). Table 5. Selected Bond Lengths [Å] and Angles [deg] for Complexes 10*/13

Ti-N(1) Ti-N(2) Ti-C(15) Ti-C(15A) N(1)#1-Ti-N(1) N(1)#1-Ti-N(2) N(1)-Ti-N(2) N(2)-Ti-N(2)#1 N(1)-Ti-C(15)#1 N(2)-Ti-C(15)#1 N(1)-Ti-C(15) N(2)-Ti-C(15) C(15)#1-Ti-C(15) N(1)-Ti-C(15A)#1 N(1)-Ti-C(15A) N(2)-Ti-C(15A) N(2)#1-Ti-C(15A) C(15A)#1-Ti-C(15A)

Figure 4. ORTEP diagram (50% probability ellipsoid) of complex 10.

(12), N(5)-Ti-N(14) ) 63.17 (8)°]. As a result, the C-N bond lengths of the two chelate units are equidistant (C-N ) 1.321 (3) Å), similar to those in the corresponding unsubstituted benzamidinate complex.21b During the selection of the best crystal of complex 10 for the X-ray analysis, solitary crystals with a more pronounced 2184 J. AM. CHEM. SOC.

9

VOL. 125, NO. 8, 2003

2.106(4) 2.117(5) 2.139(11) 2.150(4) 167.3(2) 107.35(17) 63.50(16) 96.2(2) 98.5(3) 88.9(6) 89.8(3) 153.2(3) 98.3(12) 120.3(10) 70.8(10) 131.1(10) 113.5(10) 75(2)

reddish color were observed. The X-ray analysis of this latter complex “10*” (Figure 5a) gave almost the same crystal data (unit cell parameters, Table 10) as compared to those of 10, but with different bond lengths and angles, due to the partial (22%) cocrystallization of the additional complex 13 (Table 5). Complex 13 is formed by the elimination of two methane molecules, which are produced from the symmetric C-H activation of the methyl group in the TMS moieties with the metal-methyl bonds (eq 4) (Figure 5b). The C-H activation of the TMS groups in complex 13 induces the elongation of the Ti-C bond length [Ti-C(15A) ) 2.15 (4) Å] and the shortening of the Si-N bond length [Si(1A)-N(1) ) 1.562 (10) Å], as compared to the corresponding bond distances in complex 10 [Ti-C(19) ) 2.120 (4), Si(1)-N(5) ) 1.750 (2) Å]. The

Group 4 Octahedral Benzamidinate Complexes

ARTICLES

activation of C-H moieties in titanium alkyl complexes containing TMS-amido groups has been reported in the literature.29

Figure 6. ORTEP diagram (50% probability ellipsoid) of triazine 15. Table 6. Selected Bond Lengths [Å] and Angles [deg] for Complex 15

N(1)-C(1) N(2)-C(1) N(2)-C(2) C(1)-C(3) C(2)-C(9)

1.336(5) 1.333(5) 1.344(4) 1.469(6) 1.479(8)

C(1)-N(1)-C(1)#1 C(1)-N(2)-C(2) N(2)-C(1)-N(1) N(2)-C(1)-C(3) N(1)-C(1)-C(3) N(2)-C(2)-N(2)#1

Synthesis of Hf Bis(benzamidinate) Complex. An attempt to achieve the corresponding hafnium bis(benzamidinate) dichloride complex was intended following a similar protocol, as described for the other lighter isolobal group 4 elements (eq 3), between the lithium salt of the ligand and HfCl4‚2THF, resulting in an oily yellow mixture of products containing TMEDA. Dissolving the oily compound in toluene and removing under vacuum all of the liquids afford the production of a glassy yellow solid. The 1H and 13C NMR of this solid indicate the formation of the expected complex [(4-CH3C6H4C(NSiMe3)2)2HfCl2] (14). Elemental analysis shows that complex 14 contains additional products. Dissolving the mixture in a minimum amount of toluene followed by the vacuum transfer of large amounts of hexane affords the precipitation of a yellow powder (29) (a) Putzer, M. A.; Neumu¨ller, B.; Dehnicke, K. Z. Anorg. Allg. Chem. 1998, 624, 1087. (b) Putzer, M. A.; Magull, J.; Goesmann, H.; Neumu¨ller, B.; Dehnicke, K. Chem. Ber. 1996, 129, 1401.

116.6(6) 115.4(5) 123.9(5) 117.7(4) 118.4(4) 124.7(6)

material that was found to be silent in 1H NMR. This powder is paramagnetic, exhibiting, at room temperature, an ESR signal (X-band) centered at 3360 G and ∆H ) 12 G, with a g value of 2.0017 characteristic for a Hf(III) complex.30 One of the most intriguing questions in the formation of the Hf(III) complex is the elucidation of the reducing agent entity. From the diethyl ether washing solutions of the powder material, we were able to crystallize the organic compound tris-p-tolyl-1,3,5-triazine (15), the product of the trimerization of p-tolunitrile. The formation of this triazine indicates that Hf(III) induces the reverse reaction as indicated in eq 2, yielding p-tolunitrile and the lithium salt LiN(TMS)2. The former compound trimerizes to tris-p-tolyl-1,3,5-triazine. The Hf(III) presumably is obtained by the reduction of HfCl4‚2THF with [4-CH3-PhC(NSiMe3)2Li(TMEDA)], as observed for similar Ti and Zr complexes.31 Interestingly, from the low-temperature X-ray analysis (Figure 6, Table 6), the triazine was found to be a polymorphic compound of the recent structure published in the literature.32 The difference between the two crystalline materials resides in the packing disposition of the molecules between the main plain of the triazine ring with respect to the a0b plane. X-ray cell parameters and refinement data are presented in Table 10. (30) Fakhr, A.; Mugnier, Y.; Gautheron, B.; Laviron, E. J. Organomet. Chem. 1986, 302, C7 and references therein. (31) Ray, B.; Gueta-Neyroud, T.; Kapon, M.; Eichen, Y.; Eisen, M. S. Organometallics 2001, 20, 3044. (32) Thalladi, V. R.; Muthuraman, M.; Nagia, A.; Desiraju, G. R. Acta Crystallogr. 1999, C55, 698. J. AM. CHEM. SOC.

9

VOL. 125, NO. 8, 2003 2185

ARTICLES

Figure 7.

13C

Volkis et al.

NMR of the polypropylene obtained catalyzed by complex 9 at room temperature.

Catalytic Polymerization Studies. Polymerization reactions were performed with the dimethyl complexes 9-12 activated by MAO or B(C6F5)3. Because of the large differences in polymer properties obtained with these complexes at the various reaction conditions, the polymerization results are presented separately for complexes 9-12. Polymerization of Propylene at Atmospheric Pressure Catalyzed with Complex 9. This complex was found to be a good precursor for the polymerization of propylene at atmospheric pressure at 25 °C. When activated with MAO (Al:Zr molar ratio 250:1) in toluene, complex 9 produces large amounts (8.1 × 105 gPP/mol Zr‚h) of an oily polymer with medium molecular weight Mw ) 38 000, resembling an atactic polypropylene. 13C NMR tryad and pentad analysis of this polymer shows that, contrary to the 10 expected signals for the methyl groups of an atactic polypropylene, only two major signals are observed in the region between 19.5 and 21.9 ppm (Figure 7).33 A very similar spectrum has been recently observed in the characterization of polypropylene polymerized by R-diimine nickel complexes.34 The two major signals belong to the corresponding mr and rr tryads. A very elegant analysis of similar type of polymers has been recently published.34 The small signals in the region of 15 to 19 ppm and the signals between 29 and 41 ppm corroborate the presence of 2,1 and 1,3 misinsertions. Moreover, it is possible to conclude that β-Me elimination is the major termination mechanism, as represented by the signals observed at 146 and 113 ppm, the signals between 22 and 26 ppm for the vinylic CH (C1), CH2 (C2), and the terminal carbons of the isobutylene unit (C3, C4, and C5) in Figure 7, respectively.33 When precursor 9 was activated with B(C6F5)3 (molar ratio B:Zr ) 1), under the same reaction conditions as with MAO, a highly isotactic polypropylene was obtained (mmmm ) 98%), contrary to the results obtained with MAO (eq 5). The activity of this catalytic system (1.2 × 105 gPP/mol Zr‚h) is somewhat lower than the activity of complex 9 activated with MAO. It is important to point out that complex 9 has a C2-symmetry (33) Resconi, L.; Piemontesi, F.; Franciscono, G.; Abis, L.; Fiorani, T. J. Am. Chem. Soc. 1992, 114, 1025. (34) McCord, E. F.; McLain, S. J.; Nelson, L. T. J.; Arthur, S. D.; Coughlin, E. B.; Ittel, S. D.; Johnson, I. K.; Tempel, D.; Killian, C. M.; Brookhart, M. Macromolecules 2001, 34, 362. 2186 J. AM. CHEM. SOC.

9

VOL. 125, NO. 8, 2003

octahedral geometry, suggesting that, when activated by MAO, theoretically an isotactic polymer, as obtained with B(C6F5)3, should also be expected.35

The “atactic polymer”, obtained with MAO, can be rationalized by two plausible mechanisms besides the 2,1 insertions: (1) formation of a “cationic” five-coordinated trigonal bypyramid complex (B) or a square planar pyramid intermediate (C), as a new active complex, with almost no stereodifferentiation at the propylene insertion, and (2) an intramolecular epimerization reaction of the growing polypropylene chain at the lastinserted monomeric unit (Scheme 1).36,37

Group 4 Octahedral Benzamidinate Complexes

ARTICLES

Scheme 1. Proposed Mechanism for the Intramolecular Epimerization of the Growing Polypropylene Chain at the Last-Inserted Monomeric Unit

Table 7. Data for the Polymerization of Propylene Promoted by Complex 9 Using Different Solvents, Temperature, and MAO Amounts entry

solvent

1

toluene

2 3 4 5 6 7 8

CH2Cl2 CH2Cl2 CH2Cl2 CH2Cl2 CH2Cl2 CH2Cl2 toluene

T °C

P atm

activitya A × 10-5

250

25

9.2

1.1b

250 400 1000 250 250 250 B(C6F5)3

25 25 25 0 25 50 25

9.2 9.2 9.2 5.1 9.2 17.0 9.2

2.2 7.5 7.9 0.5 2.2 26.6 2.8e

Al:Zr

Mn

Mw

MWD

mmmmc %

Mp °C

261 000 36 000 10 750 23 500 58 100 10 200 10 700 149 700 26 000 3000

440 000 86 000 26 750 42 470 82 600 18 900 26 700 271 000 51 300 9300

1.69 2.35 2.49 1.81 1.42 1.85 2.49 1.81 1.96 3.10

86d 11 90 96 98 86 90 96 98 7

142 oil 146 147 149 138 146 152 154 oil

a gr PP/mol Zr ‚ h. b Mixture of isotactic (50%) and atactic (50%) fractions of polypropylene. c Measured by fraction. e 70% atactic and 30% isotactic.

The elucidation of which of the two plausible mechanisms is responsible for the production of an “atactic polypropylene” was achieved by performing the reactions under pressure (liquid propylene). For the first mechanism, none or small changes in the stereoregularity of the polymer will be predicted, whereas for the second mechanism, a highly isotactic polymer will be expected. High-Pressure Polymerization of Propylene Catalyzed by Complex 9. When the reaction catalyzed by 9 activated with MAO is carried out at high pressure, a highly stereoregular polymer is formed. A summary of the polymerization results is presented in Table 7. To acquire the best experimental conditions, we have started the polymerizations by studying the effect of the solvent. By performing the polymerization in dichloromethane, larger activities, stereoregularities, and melting points of the polymers were observed, as compared to the results exhibited in toluene (entries 1 and 2). This increase in activity is plausible as a consequence of the polarity of the CH2Cl2, causing a greater charge separation between the cationic benzamidinate alkyl complex and the MAO anion, encouraging the insertion of the monomer, as compared to toluene. For toluene, a putative π-bond of the ring to the cationic center of complex (E) possibly takes place forming a cationic η6-toluene compound.38 This intermediate inhibits the insertion (35) Recently a C2-symmetry titanium complex has been shown to be active for the polymerization of propylene forming highly syndiotactic polymer that is formed through the chain-end mechanism. See ref 17a,b. (36) (a) Busico, V.; Cipullo, R.; Caporaso, P.; Angeloni, G.; Segre, A. L. J. Mol. Catal. A: Chem. 1998, 128, 53. (b) Busico, V.; Cipullo, R.; Monaco, G.; Vacatello, M. Macromolecules 1997, 30, 6251. (c) Busico, V.; Brita, D.; Caporaso, L.; Cipullo, R.; Vacatello, M. Macromolecules 1997, 30, 3971. (d) Busico, V.; Caporaso, L.; Cipullo, R.; Landriani, L.; Angelini, G.; Margonelli, A.; Segre, A. L. J. Am. Chem. Soc. 1996, 118, 2105. (e) Leclerc, M.; Brinzinger, H. H. J. Am. Chem. Soc. 1996, 118, 9024 and references therein. (f) Busico, V.; Cipullo, R.; Corradini, P.; Landriani, L.; Vacatello, M.; Segre, A. L. Macromolecules 1995, 28, 1887. (g) Busico, V.; Cipullo, R. J. Am. Chem. Soc. 1994, 116, 9329. (37) The additional “allylic mechanism” for the epimerization has been proposed, see: Resconi, L. J. Mol. Catal. 1999, 146, 167. This mechanism was found to be not a major pathway due to the lack of internal vinylidenic and isobutenyl groups.

13C

NMR. d Isotacticity of the isotactic

of the monomer and the termination of the polymer chain, allowing larger molecular weights and narrower molecular weight distributions, as compared to the polymers obtained in CH2Cl2.

The polymerization of propylene under higher pressure in CH2Cl2 yields an isotactic polypropylene with small amounts of stereodefects, while in toluene a mixture of isotactic and atactic products was obtained. The formation of two different polypropylene fractions in toluene can testify about the presence of two different active catalytic species. The nature of the intermediate responsible for the formation of the atactic fraction has not been fully elucidated yet. On the basis of NMR experiments, it seems that, in toluene, one of the benzamidinate ligations opens to a η1 coordination, and the solvent occupies the vacant site. Interestingly, similar heteroallylic ligations (alkoxysilyl-imido) have exhibited dynamic behaviors.39 Up to a molar ratio of Al:Zr ) 400, the activity of the catalytic complex enhances with an increase in the MAO amount (entries (38) (a) Lancaster, S. J.; Robinson, O. B.; Bochmann, M.; Coles, S. J.; Hursthouse, M. B. Organometallics 1995, 14, 2456. (b) Gillis, D. J.; Tudoret, M. J.; Baird, M. C. J. Am. Chem. Soc. 1993, 115, 2543. (c) Eisen, M. S.; Marks, T. J. J. Am. Chem. Soc. 1992, 114, 10358. (d) Eisen, M. S.; Marks, T. J. Organometallics 1992, 11, 3939. (e) Solari, E.; Floriani, C.; Chiesi-Villa, A.; Guastini, C. J. Chem. Soc., Chem. Commun. 1989, 1747. (39) (a) Duchateau, R.; Brussee, E. A. C.; Meetsma, A.; Teuben, J. H. Organometallics 1997, 16, 5506. (b) Duchateau, R.; Tuinstra, T.; Brussee, E. A. C.; Meetsma, A.; van Duijnen, P. T.; Teuben, J. H. Organometallics 1997, 16, 3511. J. AM. CHEM. SOC.

9

VOL. 125, NO. 8, 2003 2187

ARTICLES

Volkis et al.

Table 8. Data for the Polymerization of Propylene Promoted by Complex 10 with MAO entry

solvent

Al:Ti a

T °C

P atm

activityb A × 10-5

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

CH2Cl2 CH2Cl2 toluene toluene CH2Cl2 CH2Cl2 CH2Cl2 CH2Cl2 CH2Cl2 CH2Cl2 CH2Cl2 CH2Cl2 CH2Cl2 CH2Cl2 CH2Cl2 CH2Cl2

1000 1000 1000 1000 1000 1000 1000 1000 1000 300 300d 300e 300 f 500 2000 3000

25 25 25 25 -25 -10 0 10 50 25 25 25 25 25 25 25

1.0 9.2 1.0 9.2 1.5 3.0 4.5 7.0 17.0 9.2 9.2 9.2 9.2 9.2 9.2 9.2

0.0 1.9 0.0 1.9 0.6 0.3 0.6 1.0 1.7 0.4 0.4 0.4 0.2 0.3 2.6 3.9

Mn

Mw

MWD

mmmm %

type of polymer

55 400

113 800

1.51

18

elastomer

51 300

93 700

1.83

102 700 79 700 68 900 46 700 57 400 48 400 55 400 47 700 43 300 59 800 67 900

163 000 138 100 117 600 82 300 89 700 74 300 86 500 81 300 114 300 116 700 115 500

1.57 1.73 1.71 1.76 1.56 1.53 1.56 1.71 2.64 1.95 1.70

21 26 23 22 22 18 20 19 20 22 21 13 14

elastomer solidc elastomer elastomer elastomer oil elastomer elastomer elastomer elastomer elastomer elastomer elastomer

a Moles of catalyst ) 7.8 × 10-6. b gr PP/mol Ti ‚ h. c Solid with no elastomeric properties and low solubility in hot trichlorobenzene although enough to measure mmmm content. d 15.6 × 10-6 mol of catalyst. e 31.2 × 10-6 mol of catalyst. f 46.8 × 10-6 mol of catalyst.

2-4). Further augmentation of MAO concentration does not influence the polymerization rate, but rather the properties of the polypropylene. Likewise, by raising the Al:Zr ratio, the melting points, molecular weights, and isotacticities of the polymers increase with a concomitant reduction in the molecular weight distribution (MWD). By performing the reaction at elevated temperatures, higher activities, stereoregularities, and molecular weights of polypropylene are achieved (entries 5, 6, and 7). These results suggest that an increase of the temperature induces faster insertion rates as compared to the rate of the epimerization, resulting in higher isotacticities. Worthy of note is that in the polymerization of propylene, performed by complex 9 activated with B(C6F5)3, in toluene (entry 8), two polymeric fractions (70% atactic and 30% highly isotactic) are attained as is observed with the MAO. In CH2Cl2, no polymerization is observed. Comparing the stereoregularities of the polymers obtained at atmospheric or at high pressure, when complex 9 was activated by MAO or B(C6F5)3, it is remarkably the substantial effect of the counterion. When B(C6F5)3 is used at atmospheric pressure in toluene, a highly isotactic polymer is obtained, while two polymer fractions are accountable at higher monomer concentrations. The opposite effect is observed for MAO allowing large isotacticities at high pressures, but only in dichloromethane. Therefore, the stereoregularity of polypropylene promoted by the system “9 + MAO” can be tailored as presented in eq 6. It is important to point out that 13C NMR analysis of the chain ends of the polymers, obtained at high monomer concentration, also shows that the β-methyl elimination is the exclusive termination chain mechanism for these catalytic systems. Statistically, we can deduce that at atmospheric pressure, the epimerization is observed every small number of insertions, forming a -mmrrmmrrmmrrmmrr- microstructure responsible for the two major signals with similar integration, and the almost absent signal for the mmmr pentad, as presented in Figure 7. The lack of 2,1 and 1,3 misinsertion signals in the 13C NMR for the polymers obtained at high pressures indicates the rapidity of the 1,2 insertion, as compared to the misinsertions. A further endorsement that the mechanism presented in Scheme 1 is responsible for the epimerization of the last inserted unit was obtained by reacting complex 9 with MAO and 2188 J. AM. CHEM. SOC.

9

VOL. 125, NO. 8, 2003

1-octene.23,40 Because the polymerization of 1-octene is extremely slow, it will be expected that if the epimerization is an operative pathway, a β-hydrogen elimination can take place from either the two methyl groups or the methylene group attached to the polymer chain (D in Scheme 1). In the first route, no changes in the alkene are expected, but in the second pathway, an isomerization of the double bond will be observed. The fact that 1-octene was isomerized to a mixture of octenes displays strong evidence for the formation of the intermediate complex D in Scheme 1. Polymerization of Propylene Promoted by the Titanium Benzamidinate Complex 10. When the polymerization of propylene is performed using the titanium complex 10, in most cases, an elastomeric polypropylene is formed with properties depending on the polymerization conditions. Results for the polymerization of propylene catalyzed by complex 10 activated with MAO are presented in Table 8. Table 8 shows that, contrary to complex 9, complex 10 is not active in the polymerization of propylene at atmospheric pressure either in CH2Cl2 or in toluene (entries 1 and 3). The solvent-metal interaction seems to be much stronger in titanium (40) Averbuj, C.; Eisen, M. S. J. Am. Chem. Soc. 1999, 121, 8755.

Group 4 Octahedral Benzamidinate Complexes

Figure 8. 13C NMR spectra of polypropylene obtained at different temperatures by complex 10 activated with MAO. The temperature of the polymerization is indicated at each spectrum.

than in zirconium because of the effective charge at the metal center, indicating that at low pressure for 10 both solvents inhibit almost completely the monomer insertion. At high monomer concentration, 10 activated by MAO is an active precursor in both solvents (entries 2 and 4). At -25 °C, a solid polypropylene is formed. This polymer contains almost no 2,1 or 1,3 misinsertions (Figure 8a) and is almost immiscible in hot trichlorobenzene. The steady augmentation of the temperature up to 25 °C leads to a continuous increase of the polymerization rate, an increase in the number of the 2,1 and 1,3 misinsertions, and a decrease in the polymer molecular weight (entries 5-8 and Figure 8b-e), with no major change in the mmmm content. In this range of temperatures (-10-25 °C), elastomeric polymers are formed.41 At 50 °C, a small change in the activity is observed, while the molecular weight of the polymer continues to decrease producing a viscous oil (entry 9) (Figure 8f). (41) For elastomeric polymerization using metallocenes, see: (a) Tagge, C. D.; Kravchenko, R. L.; Lal, T. K.; Waymouth, R. M. Organometallics 1999, 18, 380 and references therein. (b) Lin, S.; Hauptman, E.; Lal, T. K.; Waymouth, R. M.; Quan, R. W.; Ernst, A. B. J. Mol. Catal. A: Chem. 1998, 136, 23 and references therein. (c) Maciejewski Petoff, J. L.; Agoston, T.; Lal, T. K.; Waymouth, R. M. J. Am. Chem. Soc. 1998, 120, 11316 and references therein. (d) Kravchenko, R.; Masood, A.; Waymouth, R. M.; Myers, C. I. J. Am. Chem. Soc. 1998, 120, 2039. (e) Hu, Y.; Krejchi, M. T.; Shah, C. D.; Myers, C. L.; Waymouth, R. M. Macromolecules 1998, 31, 6908. (f) Carlson, E. D.; Krejchi, M. T.; Shah, C. D.; Terakawa, T.; Waymouth, R. M.; Fuller, G. G. Macromolecules 1998, 31, 5343. (g) Bruce, M. D.; Waymouth, R. M. Macromolecules 1998, 31, 2707. (h) Maciejewski Petoff, J. L.; Bruce, M. D.; Waymouth, R. M.; Masood, A.; Lal, T. K.; Quan, R. W.; Behrend, S. J. Organometallics 1997, 16, 5909. (i) Bruce, M. D.; Coates, G. W.; Hauptman, E.; Waymouth, R. M.; Ziller, J. W. J. Am. Chem. Soc. 1997, 119, 11174. (j) Coates, G. W.; Waymouth, R. M. Science 1995, 267, 217. (k) Llinas, G. H.; Dong, S. H.; Mallin, D. T.; Rausch, M. D.; Lin, Y. G.; Winter, H. H.; Chien, J. C. W. Macromolecules 1992, 25, 1242. (l) For recent formation of elastic polypropylene with metallocenes due to a large number of stereoregular insertions “mistakes”, see: Dietrich, U.; Hackmann, M.; Rieger, B.; Klinga, M.; Laskela¨, M. J. Am. Chem. Soc. 1999, 121, 4348. (m) For a recent publication regarding η3 f η1 dynamic coordination and the effect in the polymerization of propylene, see: ref 19, Plat, D. The ReactiVity of Group IV Aminophosphine Complexes; Ph.D. Thesis; Technion, Israel, 2000 and Shaviv, E.; Sc, M. Heteroallylic Early Transition Metal Complexes; Thesis; Technion, Israel, 2000. (n) For elastomeric polypropylene obtained by other group 4 complexes, see refs 18, 19, and 31.

ARTICLES

The 13C NMR spectrum (Figure 8) of the polymers shows that at 50 °C, large signals are present in the region between 32 and 45 ppm. These signals belong to the 2,1 and 1,3 misinsertions of propylene forming ethyl and butyl domains at the polymer chain.2f,34,42a The increase of misinsertions observed with the elevation of the temperature accounts for the formation of the various forms of polypropylene (isotactic, elastomeric, and oily). It is important to point out the effect of the amount of MAO. The higher the MAO amount is, the better the polymerization activity is, although beyond the Al:Ti ratio of 300 a plateau is reached, regarding the molecular weight of the polymers (entries 10, 14-16). The effect of the amount of the catalyst was measured by keeping the Al:Ti ratio constant, but increasing the amount of the catalyst (entries 10-13). Hence, similar activities are always observed regardless of the higher concentrations of the catalyst, presumably due to the formation of inactive dimeric species. The different types of polymers that are achieved under pressure at room temperature by either complexes 9 (highly isotactic) or 10 (highly epimerized and a large number of 2,1 and 1,3 insertions) can be rationalized due to the R-agostic interactions for both complexes. The strong interactions in complex 9 inhibit the β-hydrogen elimination (less epimerizations), whereas for the titanium complex 10, this interaction has been shown to be much weaker.41b This effect also accounts for the absence of 2,1 misinsertions promoted with complex 9. The strong interaction seems to be responsible for the occupation of the active coordination site by the hydrogen preventing the 2,1 misinsertion. Influence of Substituents at the Benzamidinate Ligands on the Catalytic Activity of Complexes 11 and 12. A conceptual question regarding the catalytic activity of the benzamidinate complexes involves the effect of different groups at the aromatic ring. To shed some light, we have prepared and studied complexes 11 and 12, which are isolobal to complexes 9 and 10, respectively. In the former complexes, a hydrogen atom is at the para-position of the aromatic rings. The polymerization results obtained for the unsubstituted benzamidinate complexes (11, 12) under similar reaction conditions are presented in Table 9. Comparison of the activities for the zirconium complexes 9 and 11 (Tables 7 and 9) shows that for the unsubstituted complex 11, the activity in toluene is larger than that of complex 9 in either toluene or CH2Cl2. Larger activity is also observed for the unsubstituted titanium complex 12 as compared to complex 10 (Tables 8 and 9). The polypropylene obtained with complex 11 is characterized by a high molecular weight (Mw of ∼1.9 × 106). The molecular weights of the polymers obtained with complex 12 in CH2Cl2 are much lower than those obtained by complex 10, whereas in toluene the contrary is observed (compare entries 2, 4, and 14 in Table 8 with entries 8, 5, and 7 of Table 9, respectively). A plausible elucidation for the increase in activity of the unsubstituted complexes (11 and 12) in the polymerization of propylene, as compared to the complexes with the substituted benzamidinate ligands (9 and 10), relates to the difference in the electronic effects of both ligations on the cationic metal (42) (a) NMR of Polymers; Bovey, F. A., Miray, P. A., Eds.; Academic Press: San Diego, CA, 1996. (b) Margl, P.; Deng, L.; Ziegler, T. Organometallics 1998, 17, 933. J. AM. CHEM. SOC.

9

VOL. 125, NO. 8, 2003 2189

ARTICLES

Volkis et al.

Table 9. Data for the Polymerization of Propylene Promoted by Benzamidinate Complexes 11 and 12a entry

cat.

solvent

Al:M

activityb A x 10-5

Mn

Mw

MWD

mmmmc %

type of polymer

1 2 3 4 5 6 7 8

11 11 11 12 12 12 12 12

toluene toluene toluene toluene toluene toluene CH2Cl2 CH2Cl2

500 1000 2000 500 1000 2000 500 1000

2.2 12.1 9.3 2.2 28.5 14.0 1.8 9.9

1600 380 200 866 100 92 400 125 000 137 000 12 000 10 200

3100 611 600 1 982 000 169 900 310 100 211 700 35 100 27 500

1.96 1.61 1.2 1.84 2.48 1.54 2.91 2.70

15 20 19 12 17 27 9 11

elastomer elastomer solid elastomer elastomer elastomer elastomer elastomer

a

25 °C, 9.2 atm. b gr PP/mol M ‚ h. c Measured by

13C

NMR.

Table 10. Crystal Data and Refinement Details for Complexes 2, 4, 9, 10, 10*/13 and 15 complex

empirical formula formula weight temperature wavelength crystal system space group unit cell dimensions

volume Z, calculated density absorption coefficient F(000) crystal size θ range for data collection limiting indices

reflections collected/unique completeness to highest θ refinement method data/restraints/parameters goodness-of-fit on F 2 final R indices [I > 2σ(I)] R indices (all data) largest diff. peak and hole

2

4

9

10

10*/13

15

C40H56Li2N6Si4 747.15 230(2) K 0.7107 Å monoclinic P21/n a ) 11.4006(2) Å R ) 90° b ) 24.2914(4) Å β ) 98.75 (6)° c ) 16.7460(3) Å γ ) 90° 4583.60(14) Å3 4, 1.083 Mg/m3 0.162 mm-1 1600 0.15 × 0.3 × 0.5 mm 1.49-25.50°

C19H39LiN4Si2 386.66 230(2) K 0.71070 Å monoclinic P21/c a ) 10.6540(4) Å R ) 90° b ) 13.4360(6) Å β ) 91.6800(18)° c ) 18.1020(8) Å γ ) 90° 2590.14(19) Å3 4, 0.992 Mg/m3 0.146 mm-1 848 0.15 × 0.20 × 0.30 mm 1.89-25.03°

C30H56N4Si4Zr 676.37 210(2) K 0.71073 Å triclinic P1h a ) 11.1578(8) Å R ) 100.1940(10)° b ) 11.8659(9) Å β ) 106.3370(10)° c ) 15.8740(11) Å γ ) 98.7370(10)° 1939.2(2) Å3 2, 1.158 Mg/m3 0.430 mm-1 720 0.50 × 0.40 × 0.40 mm 1.37-26.40°

C15H28N2Si2Ti0.50 316.52 230.0(1) K 0.71069 Å monoclinic I2/a a ) 20.1172(5) Å R ) 90° b ) 8.7559(2) Å β ) 95.2520(10)° c ) 21.9639(5) Å γ ) 90° 3852.57(16) Å3 8, 1.091 Mg/m3 0.369 mm-1 1368 0.04 × 0.18 × 0.37 mm 2.51-25.05°

C14.78H24.97N2Si2Ti0.50 310.85 200.0(1) K 0.71069 Å monoclinic I2/a a ) 20.039(10) Å R ) 90° b ) 8.678(4) Å β ) 94.72(5)° c ) 21.829(10) Å γ ) 90° 3783(3) Å3 8, 1.092 Mg/m3 0.375 mm-1 1333 0.15 × 0.23 × 0.31 mm 2.04-25.04°

C12H10.50N1.50 175.72 220.0(1) K 0.71070 Å orthorhombic Pmn21 a ) 21.630(4) Å R ) 90° b ) 9.458(2) Å β ) 90° c ) 4.5734(9) Å γ ) 90° 935.5(7) Å3 4, 1.248 Mg/m3 0.074 mm-1 372 0.18 × 0.04 × 0.01 mm 2.15-30.50°

0 g h g 13, 0 g k g 28, -19 g l g 19 8089/8089 [R(int) ) 0.0000] 99.7%

0 g h g 12, 0 g k g 15, -21 g l g 21 4558/4558 [R(int) ) 0.0000] 99.6%

-13 g h g 13, -10 g k g 14, -19 g l g 19 10 962/7543 [R(int) ) 0.0604] 99.6%

-23 g h g 18, 0 g k g 10, -26 g l g 17 3406/3406 [R(int) ) 0.0000] 99.7%

-23 g h g 18, 0 g k g 10, 0 g l g 26 3432/3344 [R(int) ) 0.0428] 100.0%

0 g h g 29, 0 g k g 13, -52 g l g 6 10 623/2438 [R(int) ) 0.0760] 91.5%

full-matrix leastsquares on F 2 8089/0/693 1.034 R1 ) 0.0444, wR2 ) 0.1023 R1 ) 0.0757, wR2 ) 0.1115 0.175 and -0.234 e Å-3

full-matrix leastsquares on F 2 4558/0/308 0.989 R1 ) 0.0648, wR2 ) 0.1475 R1 ) 0.1485, wR2 ) 0.1715 0.276 and -0.222 e Å-3

full-matrix leastsquares on F 2 7539/0/426 1.028 R1 ) 0.0608, wR2 ) 0.1413 R1 ) 0.1038, wR2 ) 0.1892 0.458 and -0.547 e Å-3

full-matrix leastsquares on F 2 3406/0/199 1.099 R1 ) 0.494, wR2 ) 0.1361 R1 ) 0.0711, wR2 ) 0.1450 0.352 and -0.224 e Å-3

full-matrix leastsquares on F 2 3344/0/222 1.044 R1 ) 0.0927, wR2 ) 0.1697 R1 ) 0.1758, wR2 ) 0.1919 0.455 and -0.230 e Å-3

full-matrix leastsquares on F 2 2438/0/155 1.096 R1 ) 0.0657, wR2 ) 0.1270 R1 ) 0.2407, wR2 ) 0.1980 0.195 and -0.174 e Å-3

center. The induction Taft constants (σ*), which quantitatively characterize the induction effect of an aliphatic substituent in an aromatic hydrocarbons, are +0.49 for the H atom and 0.00 for the CH3 group.43 Hence, the methyl group has a more negative inductive effect, that is, greater electron-donor properties, than the hydrogen atom, increasing the electron density at the phenyl ring and decreasing the positive charge at the metal center. The reduction of the cationic character at the metal center induces a weaker bond between an incoming molecule of propylene, reducing the polymerization activity of the complex. The augmentation of the electron density at the metal center in complex 9 inhibits not only the polymerization rate, but also (43) (a) Taft, R. W. J. Phys. Chem. 1960, 64, 1805. (b) March, J. AdVanced Organic Chemistry, 3rd ed.; Wiley-Interscience: New York, 1985; Chapter 9. 2190 J. AM. CHEM. SOC.

9

VOL. 125, NO. 8, 2003

the rate of the epimerization reaction (slowing down the β-hydrogen elimination), resulting in larger domains of the isotactic pentads, and therefore highly isotactic polymers. For the titanium complex 10, besides the inhibition rate, no restrain takes place for the epimerization reaction, allowing the production of elastomeric polymers. Structure of the Elastomeric Polypropylenes. As already mentioned above, in the polymerization of propylene at higher monomer concentrations using the complexes 10, 11, and 12, an elastomeric polypropylene was formed. It is essential and fundamental to compare the chemical structures of the obtained elastomers with the structure of the elastomeric polypropylenes, described in the literature. Three types of elastomeric polypropylene are known: (i) a large molecular weight atactic polymer,44 (ii) polymers with

Group 4 Octahedral Benzamidinate Complexes

alternating isotactic and atactic blocks,40a-k and (iii) polymers obtained by the “dual-side” mechanism.40l To elucidate the structure of the obtained elastomeric polypropylene, its 13C NMR spectra was compared with the spectrum of the “atactic oil” and the isotactic polypropylenes, prepared by the zirconium complex 9. On the basis of the NMR data, for all of the samples, the statistical lengths of the isotactic blocks between two neighboring epimerization stereodefects were calculated. According to these calculations, the length of an isotactic block before a stereodefect was found to be between 35 and 45 CH3 groups for an isotactic polymer (mmmm ≈ 90%) and between 7 and 8 CH3 groups for the atactic sample (mmmm ≈ 7%). For the elastomeric polymers obtained with complex 10, the length of the isotactic block was calculated to be between 11 and 27 CH3 groups. Thus, for the elastomeric polypropylene, the length of the statistical isotactic fragment between two stereodefects was found to be shorter than that obtained for an isotactic polymer and longer than that observed for an atactic sample. Therefore, it is plausible to assume that the elastomeric polypropylene prepared with these complexes differs, in principle, from the other three above-mentioned types of elastomers. Thus, contrary to the high molecular weight atactic elastomer,43 our samples have an isotactic structure, in which longer isotactic domains are disposed between stereodefects. Simultaneously, different from the alternating isotactic-atactic block elastomers,40 where the alternating isotactic and atactic domains have commensurate lengths, our products are characterized by frequent alternation of the isotactic domains with many stereodefects. As compared to the polymers obtained through the “dual-side” mechanism, which exhibit large mmmm contents (up to 72%),40l our polymers reside with lower stereoregularities. In the “dual-site” mechanism, each site has a different symmetry, and, by the back-skipping of the polymeric chain, two stereochemistries for the insertions are possible. In our complexes, a back-skipping of the polymer chain will induce the same symmetry, thus inducing the same type of stereoregular insertion. The stereoregular errors are formed because of two competing reactions, the insertion of propylene and the intramolecular epimerization of the growing chain at the last inserted unit. The rate correlation of these two reactions influences the amount and length of the isotactic domains between the stereoerrors. We have utilized atomic force microscopy (AFM) to discriminate between the crystalline and the amorphous areas in the homogeneous polymer. The use of AFM to characterize the morphology polymer samples on the nanometer scale is well documented in the literature.45 Topography, phase imaging, and lateral force measurements are efficient tools to examine polymer structure and properties on the nanometer scale. Here, topographic and phase imaging techniques were used to (44) Resconi, L.; Jones, R. L.; Rheingold, A. L.; Yap, G. P. A. Organometallics 1996, 15, 998. (45) (a) Haeringen, D. T. V.; Varga, J.; Ehrenstein, G. W.; Vancso, G. J. J. Polym. Sci., Part B: Polym. Phys. 2000, 38, 672. (b) Ivanov, D. A.; Nysten, B.; Jonas, A. M. Polymer 1999, 40, 5899. (c) Xu, K.; Gusev, A. I.; Hercules, D. M. Surf. Interface Anal. 1999, 27, 659. (d) Orefice, R. L.; Brennan, A. Mater. Res. 1998, 1, 19. (e) Pfau, A.; Janke, A.; Heckmann, W. Surf. Interface Anal. 1999, 27, 410. (f) Tomasetti, E.; Legras, R.; Nysten, B. Nanotechnology 1998, 9, 305. (g) Albrecht, T. R.; Dovek, M. M.; Lang, C. A.; Gru¨tter, P.; Quate, C. F.; Kuan, S. N. J.; Frank, C. W.; Pease, R. F. W. J. Appl. Phys. 1988, 64, 1178. (h) Landman, U.; Luedke, W. D.; Nitzan, A. Surf. Sci. 1989, 10, L177. (i) Wawkuschewski, A.; Cantow, H.-J.; Magonov, S. N.; Sheiko, S.; Mo¨ller, M. Polym. Bull. 1993, 31, 693. (j) Wawkuschewski, A.; Cantow, H.-J.; Magonov, S. N. AdV. Mater. 1994, 6, 476.

ARTICLES

Figure 9. AFM pictures of different polypropylenes. (a) Isotactic polymer from Table 7, entry 4. (b) Elastomeric polymer from Table 8, entry 2. (c) Atactic polymer fraction from Table 7, entry 8.

characterize the morphology of the different types of polypropylene samples. Samples of the different polymers were spin-coated on glass, and then left to dry at ambient temperature and atmosphere. Figure 9a-c depicts typical phase images of isotactic, elastomeric, and atactic polypropylene samples, respectively. Topographic images taken simultaneously fail to resolve any significant detail within the entire scan range, an indication that the differences in phase shift originate from differences in tipsurface interactions and not from topographical differences. The sample of the isotactic polymer consists of a mosaic of crystalline islands (brighter spots in the image) embedded in J. AM. CHEM. SOC.

9

VOL. 125, NO. 8, 2003 2191

ARTICLES

Volkis et al.

Figure 10. 13C NMR spectrum of complex 9 (top) and the corresponding cationic complex obtained by the stoichiometry reaction with the cocatalyst B(C6F5)3 (bottom).

an amorphous phase (darker areas) of the same material. The elastomeric polymer is composed of long interpenetrated and branched fibrils of crystalline character that interconnect amorphous regions. This phase image provides further support to the concept of microheterogeneous crystallinity of the elastomeric phase, caused by different crystalline domains that are characterized by a slightly different melting point. This set of heterogeneous crystalline phases is claimed to yield a broad and undefined melting zone. The atactic polymer is predominantly amorphous with a low density of crystalline domains. Activation of the Benzamidinate Complexes by the Different Cocatalysts. The polymerization of propylene promoted by the benzamidinate complexes was carried out using either MAO or B(C6F5)3 as cocatalysts. To shed some light on the structure of the active cationic complexes, we have followed the changes of the benzamidinate complexes when reacted with the B(C6F5)3 cocatalyst under olefin starving conditions, by 13C and 19F NMR spectroscopy. The 13C NMR spectra of complex 9 and its mixture with an equivalent amount of B(C6F5)3 in BrC6D5 are shown in Figure 10. The signal of the Zr-CH3 (43 ppm) moves downfield (62.3 ppm) upon the reaction with the cocatalyst as expected for the formation of a cationic metal-alkyl group.4,46 A larger shift was observed for the corresponding titanium complex 10, showing a displacement from 70 to 110 ppm in its cationic form. It is important to point out that the spectrum presented in Figure 10b for the cationic complex was obtained after heating the reaction mixture to 90 °C for 2 h to achieve a complete conversion. For complex 10, the shift of the methyl group is obtained regardless of any heating. Despite the similar character of the active species formed under activation of the complexes with B(C6F5)3, they behave totally different in the polymerization of propylene. Thus, the activity of the cationic complex 9 at high pressure is rather small at room temperature, but it increases if it undergoes a preliminary heating stage and recooling to the reaction temperature. On the contrary, the precursor 10 activated with B(C6F5)3 is inactive in the polymerization, regardless of any heating. The 19F NMR spectra of complex 9 with an equimolar amount of the cocatalyst, B(C6F5)3, before and after heating, are shown in Figure 11a and b, respectively. At room temperature (Figure (46) (a) Yang, X.; Stern, C. L.; Marks, T. J. J. Am. Chem. Soc. 1994, 116, 10015. (b) Deck, P. A.; Marks, T. J. J. Am. Chem. Soc. 1995, 117, 6128. (c) Wu, Z.; Jordan, R. F.; Petersen, J. L. J. Am. Chem. Soc. 1995, 117, 5867. (d) Erker, G.; Ahlers, W.; Frohlich, R. J. Am. Chem. Soc. 1995, 117, 5853. (e) Bochmann, M.; Lancaster, S. J.; Robinson, B. O. J. Chem. Soc., Chem. Commun. 1995, 2081. 2192 J. AM. CHEM. SOC.

9

VOL. 125, NO. 8, 2003

Figure 11. 19F NMR spectra of complex 9 with B(C6F5)3 at room temperature (a) and after heating (b).

11a), the spectra show two sets of signals. The signals marked 1, 2, and 3 belong to the formed cationic complex, whereas the other three signals belong to an intermediate unsolved structure. By heating and cooling the mixture, a reaction is observed achieving a quantitative conversion toward the cationic complex (Figure 11b). The chemical shift difference between the m- and p-19F of the anion CH3B(C6F5)3 can also be indicative of the anion coordination.47 Hence, values of ∆δ (m,p-F) between 3 and 6 ppm indicate coordination, whereas values below 3 ppm indicate noncoordination. For the Zr complex, a difference of ∆δ (m,p-F) ) 2.28 ppm is observed, indicative for a noncoordinating ion pair, corroborating the results obtained in the polymerization of propylene by complex 9 in CH2Cl2. The 19F NMR spectra of complex 10 with an equimolar amount of the cocatalyst B(C6F5)3 show the immediate formation of at least two inactive compounds (six new signals besides the starting cocatalyst) with no resemblance in the chemical shifts to other active or nonactive B(C6F5)3-containing metallocene complexes.46 Conclusions

Several early-transition octahedral metal complexes containing the chelating benzamidinate ligation were prepared. These complexes exhibit a C2-symmetry as displayed in their X-ray diffraction studies. The reaction of the compounds with a cocatalyst produces the corresponding cationic complexes that are active catalysts for the polymerization of propylene. Depending on the nature of the complexes, either highly stereoregular or elastomeric polymers can be obtained. Moreover, the type of polymer can be modulated by the pressure of the monomer. The elastomeric polymers are characterized by an alternation of short isotactic domains with stereodefects that are encountered by the epimerization of the growing polymeric chain at the last monomeric insertion. The use of changing (47) (a) Bochmann, M.; Green, M. L. H.; Powell, A. K.; Saβmannshausen, J.; Triller, M. U.; Wocadlo, S. J. Chem. Soc., Dalton Trans. 1999, 43. (b) Horton, A. D.; de With, J.; Linden, J. v. d.; Weg, H. v. d. Organometallics 1996, 15, 2672.

Group 4 Octahedral Benzamidinate Complexes

pressure to obtain a different block homo-copolymer is under investigation and will be reported shortly. Experimental Section General Procedure. All manipulations were carried out with the exclusion of oxygen and moisture using flamed Schlenk-type glassware and high vacuum (10-5 Torr) techniques. For storage of air-sensitive materials, a nitrogen-filled “Vacuum Atmospheres” glovebox with a medium capacity recirculator (1-2 ppm O2) was used. The gases (argon, nitrogen, propylene) were purified by passage through a MnO oxygen removal column and a Davison 4 Å molecular sieves column. Analytically pure solvents were distilled under argon from potassium benzophenone ketyl (tetrahydrofuran), Na/K alloy (diethyl ether, hexane), Na (toluene), or P2O5 (dichloromethane). All solvents for vacuum line manipulations were stored in a vacuum over Na/K alloy. Nitrile compounds (Aldrich) and TMEDA were degassed and freshly distilled under argon. Methylalumoxane cocatalyst (Witco) was prepared from a 30% suspension in toluene by vacuum evaporation of the solvent at 25 °C/10-5 Torr. Tris(pentafluorophenyl)boron cocatalyst was prepared according to the literature.48 HfCl4‚2THF, ZrCl4, and TiCl4 were purchased and used as received (Aldrich). NMR spectra were recorded on Bruker AM-200 and AM-400 spectrometers. Chemical shifts for 1H NMR and 13C NMR were referenced to internal solvent resonances and reported relative to SiMe4. The polypropylene NMR experiments were conducted in 1,2,4-trichlorobenzene at 130 °C with 20% DMSO-d6. The NMR experiments of the benzamidinate complexes were conducted on Teflon valve-sealed tubes after vacuum transfer of the solvent in a high vacuum line. 19F NMR experiments were performed in toluene, and the chemical shifts were reported relative to CCl3F. Complexes 1,25 2,25 5,23 6,23 7,21b,22d,i 8,21b,22d,i 11,21b,22d and 1221b,22d were prepared as described in the literature. Melting points of isotactic polypropylene were determined on a differential scanning calorimeter (DSC). Three runs (first heating, cooling, second heating) were performed at a heating rate of 10 °C/ min in the temperature range 30-190 °C. The second-heating melting peak temperature was taken as a melting point. Molecular weights of polymers were determined either by viscosimetric measurements49 or by the GPC method. The latter was performed on a Waters-Alliance 2000 instrument using 1,2,4-trichlorobenzene (HPLC) as the mobile phase at 150 °C. AFM measurements were performed on a DI3100 AFM machine (Veeco) equipped with an acoustic shield and vibration isolation table (TMC) using Si tips. For complexes 9 and 13, X-ray diffraction experiments were carried out with a Philips PW1100/20 four-circle diffractometer. Because of the extreme sensitivity of all synthesized complexes to oxygen and moisture, a suitable crystal for X-ray analysis was placed inside a glovebox in dry and degassed Parathon oil (Du-Pont). It was then mounted on a diffractometer, where it met a cold stream of nitrogen at 200 K. Reflections were collected, and intensities were corrected in the usual way except for absorption. The structure was solved by direct methods,50 and refinement, based on F, was made by block-diagonal least-squares.51 All non-hydrogen atoms were refined anisotropically in two blocks. Hydrogen atoms were included at calculated positions and refined isotropically in one block. The d(C-H) used was 1.08 Å. Measurement conditions and structure refinement are summarized in Table 10. For compounds, 2, 4, 10, and 15, X-ray crystallographic experiments were carried out on a Nonius-Kappa CCD diffractometer with graphite(48) Massey, A. G.; Park, A. J.; Stone, F. G. A. J. Organomet. Chem. 1964, 2, 245. (49) Allcock, H. R.; Lampe, F. W. Contemporary Polymer Chemistry, 2nd ed.; Prentice Hall: NJ, 1990; Chapter 15. (50) Sheldrick, G. M. SHELXS 86, Program for the solution of crystal structures; University of Go¨ttingen, 1986. (51) Sheldrick, G. M. SHELX 76, Program for crystal structure refinement; Chemical Laboratory, Cambridge, 1976

ARTICLES monochromatized Mo KR radiation. The crystals were placed into a Parathon-N oil in a glovebox. Single crystals were mounted on the diffractometer under a stream of cold N2 at 220 K. Data collection and reduction and cell refinements were carried out with the Nonius software package.52 The structure solution was carried out by the SHELXS 9753 and SHELXSL 9754 software packages, respectively. The ORTEP program incorporated in the TEXRAY structure analysis package was used for molecular graphics.55 Relevant crystallographic information is summarized in Table 10. Synthesis of p-CH3C6H4C(NSiMe3)2Li‚TMEDA (3). To a well stirred solution of 5.42 g (32.5 mmol) of LiN(TMS)2 in 50 mL of hexane at 0 °C was added 3.93 g (33.6 mol) of 4-methylbenzonitrile by a syringe in an argon flow. The mixture was stirred at room temperature for 3 h, and then 5.0 g (42.0 mmol) of TMEDA was added. The red-brown solution formed was stirred for an additional 3 h. After the reaction mixture was cooled overnight at -50 °C, a crystalline material precipitated that was cold filtered and dried under high vacuum to obtained 11.6 g (86%) of red-brown crystals of 3: mp 112 °C (dec). 1 H NMR (C6D6, 200.13 MHz): δ ) 7.22 (d, 3J ) 8 Hz, 2H, Ph), 6.92 (d, 3J ) 8 Hz, 2H, Ph), 2.1 (s, 3H, CH3-Ph), 1.98 (s, 12H, CH3-N), 1.74 (s, 4H, CH2-N), 0.08 (s, 18H, TMS). 13C NMR (C6D6, 50 MHz): δ ) 182.0 (N-C-N), 138.9, 137.2, 128.9, 128.1, 126.8 (Ph), 56.5 (CH2-N), 45.6 (CH3-N), 21.4 (CH3-Ph), 3.0 (TMS). Synthesis of Ligand C6H5C(NSiMe3)2Li‚TMEDA (4). Complex 4 was prepared according to a modified literature procedure.24 A suspension solution of 6.5 g (38.9 mmol) of LiN(TMS)2 in 100 mL of diethyl ether was reacted for 1 h with 4.62 g (39.8 mmol) of TMEDA. The reaction mixture was cooled to -10 °C, and 4.01 g (38.9 mol) of benzonitrile was added via a syringe under an argon flow. The reaction was stirred for 10 h at room temperature, and a crystalline product began to precipitate. Slow cooling of the reaction mixture to -40 °C overnight induced the precipitation of light yellow crystals, which were cold filtered and vacuum-dried to obtain 13.2 g (88%) of ligand 4. For spectroscopic characterization, see ref 25. Synthesis of [4-CH3-C6H4C(NTMS)2]2ZrMe2 (9). 1.03 g (1.4 mmol) of complex 5 was dissolved in 50 mL of diethyl ether, and 2.16 mL of a 1.3 M solution of methyllithium in hexane (2.8 mmol) was added dropwise at -78 °C. The solvents were completely removed in a vacuum, the residue was redissolved in hexane (30 mL), and the resulting solution was filtered through a thin layer of dry Celite filteraid to remove insoluble particles. After the solution was cooled overnight at -35 °C, pale yellow crystals were cold filtered and vacuum-dried to obtain 0.95 g (98%) of complex 9. Anal. Calcd for C30H56N4Si4Zr (676.36): C, 53.3; H, 8.4; N, 8.3. Found: C, 52.8; H, 8.2; N, 7.6. mp 135 °C (dec). 1H NMR (C6D6): δ ) 7.16 (d, 3J ) 8 Hz, 2H, Ph), 7.12 (d, 3J ) 8 Hz, 2H, Ph), 1.99 (s, 3H, CH3-Ph), 1.04 (s, 3H, CH3-Zr), 0.17 (s, 18H, TMS). 13C NMR (C6D6): δ ) 184 (N-C-N), 138.8 (ipso carbon), 137.3, 130.0, 126.1 (Ph), 44.7 (CH3Zr), 21.2 (CH3-Ph), 2.3 (TMS). Synthesis of [4-CH3-C6H4C(NTMS)2]2TiMe2 (10). In a manner similar to that described for the preparation of complex 9, 1.68 g (2.5 mmol) of complex 6 was dissolved in 50 mL of diethyl ether and was reacted with 3.85 mL of 1.3 M (5.0 mmol) methyllithium solution in hexane. The reaction mixture was stirred for 8 h, and the solvents were vacuum evaporated. Next 30 mL of hexane was vacuum transferred to the residue, and LiCl was removed by filtration. Cooling the solution overnight at -40 °C resulted in the formation of brown crystals, which were cold filtered and vacuum-dried, producing 1.45 g (92%) of (52) Nonius 1997, Kappa CCD Collect Program for data collection and HKL, Schalepack and Denzo (Otwinowski & Minor, 1997) software package for data reduction and cell refinement. (53) Sheldrick, G. M. Acta Crystallogr. 1990, A46, 467. (54) Sheldrick, G. M. SHELXL97, Program for the refinement of crystal structures; University of Go¨ttingen, Germany, 1997. (55) Molecular Structure Corporation 1999, ORTEP, TEXRAY Structure Analysis Package, MSC, 3200, Research Forest Drive, The Woodlands, TX 77381. J. AM. CHEM. SOC.

9

VOL. 125, NO. 8, 2003 2193

ARTICLES

Volkis et al.

complex 10. Anal. Calcd for C30H56N4Si4Ti (632): C, 56.96; H, 8.86; N, 8.86. Found: C, 55.23; H, 8.08; N, 9.43. mp 98 °C (dec). 1H NMR (C6D6, 200.13 MHz): δ ) 7.25 (d, J ) 7 Hz, 2H, Ph), 6.85 (d, J ) 7 Hz, 2H, Ph), 2.0 (s, 6H, CH3-Ph), 1.90 (s, 6H, CH3-Ti), 0.15 (s, 18H, TMS). 13C NMR (C6D6, 50 MHz): δ ) 189 (N-C-N), 139.1, 136.8, 128.6, 126.6 (Ph), 70.2 (CH3-Ti), 21.6 (CH3-Ph), 1.9 (TMS). Synthesis of [4-CH3-C6H4C(NTMS)2]2HfCl2 (14). In a glovebox was charged a swivel frit with 0.573 g (1.6 mmol) of the dimeric ligand 1 prepared in diethyl ether25 without TMEDA, and 1.49 g (3.2 mmol) of HfCl4‚2THF. Next 50 mL of toluene was vacuum transferred, and the reaction mixture was stirred for 16 h at room temperature. All volatiles were vacuum evaporated, and 40 mL of toluene was vacuum transferred to allow the separation of LiCl. The inorganic salt was filtered, and toluene was vacuum evaporated to obtain a yellow oily material. The oil was washed several times with diethyl ether, and evaporation of the solvent allowed the formation of 0.22 g (34%) of a yellow solid. 1H and 13C NMR analysis of the solid indicate the formation of complex 14, although elemental analysis shows that additional materials are present, which are silent in NMR; see text above. 1H NMR (CDCl3, 200.13 MHz): δ ) 7.2-7.05 (m, 4H, Ph), 2.3 (s, 3H, CH3-Ph), 0.08 (s, 18H, TMS). 13C NMR (CDCl3, 50 MHz): δ ) 187.1 (N-C-N), 137.6, 136.4, 128.9, 126.8 (Ph), 2.1 (TMS). Propylene Polymerization Experiments. The catalytic polymerization of propylene was studied using complexes 9-12. Cationic complexes were prepared by activation of these precatalysts by either MAO or B(C6F5)3. Polymerization at atmospheric pressure was carried out in a 100 mL flamed round-bottom flask and in NMR J-Young tubes. Experiments at higher pressures were performed either in a 100 mL heavy-wall glass or in stainless steal reactors. The reactor was charged inside a glovebox with a certain amount of the catalytic precursor, cocatalyst, and a magnetic stirrer. The reactor was connected to a high vacuum line, and, after introducing the solvent (7-10 mL) via a syringe under an argon flow, it was frozen at liquid nitrogen temperature and pumped-down. For the polymerization at atmospheric pressure, the reactor was warmed to the reaction temperature, and propylene was used to back fill the vessel, and it was all maintained at 1.0 atm with a mercury manometer. When polymerization was performed at higher pressures, to the frozen reactor was vacuum transferred a certain amount of liquid propylene. The temperature was then raised in a thermostated

2194 J. AM. CHEM. SOC.

9

VOL. 125, NO. 8, 2003

bath, and the stirring began. The pressure in the reactor was measured by means of a manometer. After being stirred for a certain period, the mixture was quenched by exhausting the unreacted propylene, followed by the fast introduction of 40 mL of CH3OH/HCl (1:1). Polypropylene was filtered, washed with water until neutral solution was obtained, washed with acetone, and dried under vacuum. The organic fraction from the filtrate solution was separated, dried, and the solvent was evaporated. In most cases, this solution shows no atactic fraction but when appreciated the amount of it was inserted in the corresponding table. Purification of Polypropylene from Aluminum Salts. Quenching the polymerization reactions, in which MAO was used as a cocatalyst, by MeOH:HCl produces aluminum salts that are absorbed into the polymer. These inorganic salts are difficult to remove by just washing the polymer. We have been able to clean most of the salts by dissolving the polymer in a hot solution of either 1,2,4-trichlorobenzene, Decaline, or p-xylene (120 °C). The hot solution is filtered, and the filtrate is poured into cold acetone to reprecipitate the polypropylene. The latter was then washed with acetone in the Soxhlet apparatus to remove any traces of high boiling point solvents, followed by drying under vacuum.

Acknowledgment. This research was supported by the Ministry of Science, Culture and Sport, by the Fund for the Promotion of Research at the Technion, and the Entrepreneurial Mitchel Fund for Research at the Technion. M.S.E. thanks the Humboldt Foundation for support during the preparation of the manuscript. A.L. thanks the Ministry of Immigration for the KAMEA Fellowship. We thank Dr. Alexander Shames from the Ben-Gurion University at the Neguev, Beer Sheva, Israel for the ESR experiments. We thank Prof. Arnon Siegman from the Department of Material Engineering, Technion, Israel. Supporting Information Available: Additional crystallographic details, tables of all bond distances, angles, and anisotropic thermal parameters (PDF). This material is available free of charge via the Internet at http://pubs.acs.org. JA020575R