Heterojunction Organic Photovoltaic Cells as Molecular Heat Engines

Sep 15, 2011 - Heterojunction Organic Photovoltaic Cells as Molecular Heat Engines: A Simple Model for the Performance Analysis. Mario Einax*†‡ ...
4 downloads 11 Views 2MB Size
ARTICLE pubs.acs.org/JPCC

Heterojunction Organic Photovoltaic Cells as Molecular Heat Engines: A Simple Model for the Performance Analysis Mario Einax,*,†,‡ Marcel Dierl,† and Abraham Nitzan*,‡ † ‡

Fachbereich Physik, Universit€at Osnabr€uck, Barbarastrasse 7, 49076 Osnabr€uck, Germany School of Chemistry, Tel Aviv University, Tel Aviv 69978, Israel ABSTRACT: Organic heterojunction solar cells are analyzed within a minimal model that includes the essential physical features of such systems. The dynamical properties of this model, calculated using a master equation approach, account for the qualitative behavior of such systems. The model yields explicit results for currentvoltage behavior as well as performance characteristics expressed in terms of the thermodynamic efficiency as well as the power conversion efficiency at maximum power, making it possible to evaluate the optimal setup for this device model.

’ INTRODUCTION The limited supply of today’s main energy sources, such as oil and coal, will force us to rely increasingly on renewable energy sources. Besides wind and water power, energy conversion based on photovoltaic (PV) devices has received much attention as such a source. Promising systems for next generation devices are organic photovoltaic solar cells (OPV) because of their potential for low-cost processing. Of particular interest are polymer-based heterojunctions consisting of a blend of electron-donor (D) and electron-acceptor (A) material. (For reviews, see refs 1 and 2 and references therein.) A prominent acceptor material is the buckminsterfullerene (C60).36 The quest to improve the energy conversion efficiency of such systems is the focus of intensive current research. To evaluate and subsequently improve the efficiency of OPV cells, it is crucial to understand the underlying energy conversion processes and how material properties affect their overall performance. Widely accepted is the multistep generation process that starts with photon absorption by the donor (often a polymer) yielding an exciton (bounded electronhole pair). The generated exciton diffuses to the DA interface, where it dissociates into free charge carriers, which are later transported to the electrodes. The DA interface should be constructed to favor energetically fast and efficient electron transfer leading to exciton dissociation. The dynamics of electron transfer at the DA interface is of crucial importance for the performance of heterojunction solar cells, as measured by their efficiency. In considering this issue, one may address the thermodynamic efficiency η*7,8 by considering the solar cell as a heat engine operating between a hot and a cold reservoir with temperatures TS (“sun temperature”, representing the incident radiation) and T (temperature of the chemical environment), respectively. Alternatively, the conversion efficiency η9 associated with the maximum power point in the current voltage (JU) characteristic is of interest as a realistic performance r 2011 American Chemical Society

measure. Establishing the relationship between system properties that affect exciton dissociation at the DA interface and the cell efficiency is a major goal of the ongoing research. Within this effort, it is useful to consider simple model systems for which one can obtain explicit relationships between system structure and characteristic parameters and its performance measures. In this Article, we describe and analyze such a model system. Our model consists of coupled donor and acceptor molecules, each described as a two-level (highest occupied molecular level, HOMO, and lowest unoccupied molecular level, LUMO) system, situated between two electrodes. As such, it is an extension of a simpler model recently analyzed in a similar context by Rutten et al.7 but with an important additional feature  the existence of an heterojunction characterized by energetic parameters  Coulomb interaction and donoracceptor LUMO LUMO gap, which were identified as important driving factors in the operation of such systems. The system dynamics associated with this model is described by a kinetics scheme derived using a lattice gas approach,1012 similar in spirit to previous work1317 that uses a master equation approach to analyze cell dynamics. We show that an effective mechanism for both exciton pair formation and dissociation can be captured by a minimal model of this type, which can be used as a framework for discussing the current and powervoltage curves and the cell efficiency. In particular, the model leads directly to the predictions of an optimal interface energy gap Δε (usually associated with the energy difference between the lowest unoccupied molecular levels (LUMOs) of the D and A molecules) for these efficiency measures. This can be compared with the performance of an ideal device, in which nonradiative losses are absent. In this ideal case, Received: June 22, 2011 Revised: September 8, 2011 Published: September 15, 2011 21396

dx.doi.org/10.1021/jp205856x | J. Phys. Chem. C 2011, 115, 21396–21401

The Journal of Physical Chemistry C

ARTICLE

Table 1. System States and Their Occupations with Corresponding Energies occupation state

(nD1,nD2,nA1,nA2)

energy

0

(0,0,1,0)

ε0 ¼ εA1

1

(1,0,1,0)

ε1 ¼ εD1 þ εA1

2

(0,1,1,0)

ε2 ¼ εD2 þ εA1

3

(0,0,1,1)

ε3 ¼ εA1 þ εA2 þ VC þ VC 0 ¼ εA1 þ ε~A2 þ VC 0

4

(1,0,1,1)

ε4 ¼ εD1 þ εA1 þ εA2 þ VC ¼ εD1 þ εA1 þ ε~A2

5

(0,1,1,1)

ε5 ¼ εD2 þ εA1 þ εA2 þ VC ¼ εD2 þ εA1 þ ε~A2

the thermodynamic efficiency is found to decrease monotonously, whereas the power conversion efficiency still goes through a maximum, with increasing Δε.

’ MODEL AND COMPUTATIONAL DETAILS Model. The PV cell model considered here is a 1D lattice gas with two “effective” sites l = D, A. One site represents the donor (D, e.g., polymer-based material) and the second acts as acceptor (A, e.g., fullerene-based material). Each of the sites is represented as a two-state system with energy levels (εD1,εD2) and (εA1,εA2) corresponding to the (HOMO, LUMO) levels of the donor and acceptor species, respectively. In what follows, we use the notation ΔEl = εl2  εl1 (l = D, A) for the energy differences that represent the donor and acceptor band gaps and refer to Δε = εD2  εA2 as the interface or donoracceptor LUMO LUMO gap. The microstates of the system can be specified by the set of occupation numbers n = (nD1,nD2,nA1,nA2), where nlj = 0 or 1 (l = D, A; j = 1,2) if the corresponding level is vacant or occupied by an electron. To assign further realistic contents to this model, we introduce the restrictions nD1nD2 = 0 and nA1 = 1. The first of these restrictions implies that the donor can be in the ground or excited state, or, following charge separation, in positively ionized state but excludes its doubly occupied (negatively charged) state. The excited donor state (nD1,nD2) = (0,1) represents the exciton formed as result of light absorption. The second condition implies that the acceptor can be in either its ground (nA1,nA2) = (1,0) or its negative ion (nA1,nA2) = (1,1) states. Therefore, the system is characterized by six states with respect to the occupations (nD1,nD2,nA1,nA2), that we denote by the integers 0, ..., 5 as shown in Table 1. In the expressions for the states energies, VC > 0 is the Coulombic repulsion between two electrons on the acceptor, whereas VC0 > 0 is the Coulombic energy cost to move an electron away from the hole remaining on the donor. In general, we expect that VC > VC0 . The sum VC + VC0 can be thought of as the exciton binding energy in this model: It is the total Coulomb energy cost for dissociating the exciton on the donor by moving an electron to the acceptor. It is convenient to redefine ~εA2 = εA2 + VC so that the energies εj (j = 0, ..., 5) are determined by the five energy parameters εD1, εD2, εA1, ~εA2, and VC0 . At the left (donor, say) and right (acceptor) ends of the system, the device is connected with two electrodes represented

Figure 1. Minimal model of an organic heterojunction PV cell. The system consists of one donor (e.g., a suitable polymer) and one acceptor, for example, fullerene sites, each characterized by their HOMO and LUMO levels.

by free-electron reservoirs at chemical potentials μK (K = L, R). This is a highly simplified picture that disregards electron transport within the donor and acceptor phases. We have opted to make this simplification to focus on the important step of interfacial exciton dissociation, but future more realistic treatments should take these components of the overall dynamics into consideration. As sketched in Figure 1, we use the common picture by which the left reservoir is assumed to exchange electrons only with the HOMO level of the donor, whereas the right lead exchange electrons with the upper level of the acceptor. Direct electronic interaction between system and reservoirs is not explicitly taken into account, but it is implicit both in the states of molecular species adjacent to metal electrodes and in the kinetic charge transfer rates. Next, we construct the kinetic scheme for the time evolution of the average occupations Pj (j = 0, ..., 5) associated with this level structure. (See Figure 2.) In writing these equations, we make the simplifying assumption that electron exchange between molecules and metals involve only metal electrons at the electrochemical potentials μL and μR of the left and right leads (corresponding to a bias potential U = (μR  μL)/|e| where e is the electron charge). We also disregard possible environmental relaxation dynamics due to polarization effects associated with the formation of transient charged molecular species. Generalizing this dynamical picture to take such processes into account (e.g., by considering time-dependent site energies18) is another important subject for future work. The kinetics process in our scheme then corresponds to the following processes: (a) Electron transfer between levels D1 and the left electrode and between A2 and the right electrode, with rates determined by the corresponding molecular energies, moleculesleads coupling, electrochemical potentials in the leads, and the environmental temperature, T. (b) Electron transfer between donor and acceptor, determined by the coupling between them, the corresponding state energies, and the temperature, T. 21397

dx.doi.org/10.1021/jp205856x |J. Phys. Chem. C 2011, 115, 21396–21401

The Journal of Physical Chemistry C

ARTICLE

from level D1 to the left electrode, ~kR  k03 = k14 = k25 is similarly the rate from A2 to the right electrode. kL  k10 = k43 and kR  k30 = k41 = k52 are the corresponding reverse rates. The transition rate from D2 to A2 is given by ~kDA  k32, whereas the opposite rate is kDA  k23. Also, we denote by kS and knr the radiative and thermal excitation rates in the donor and by ~ks and ~knr the corresponding relaxation rates, so kS + knr  k21 = k54 and ~ks + ~knr  k12 =k45. Computational Details. The master equation with the rates eqs 18 that describe the time evolution of the probabilities Pj = P(nD1,nD2,nA1,nA2) (j = 0, ..., 5) to be in the six possible states thus reads dP0 ðtÞ ¼ k01 P1 ðtÞ þ k03 P3 ðtÞ  ðk10 þ k30 ÞP0 ðtÞ dt

Figure 2. Six accessible microstates of the model system considered. The probability to find the system in state j (j = 0, ..., 5) is denoted Pj.

(c) Light-induced electron excitation (rate ks) and relaxation (rate ~ks) between donor levels D1 and D2. These rates are modeled as thermal rates determined by the corresponding state energies and radiative coupling, and the “sun temperature” Ts. (d) Radiationless (thermal) electron transitions between level D1 and D2 with rates knr (excitation) and ~knr (relaxation), determined as in (c) except that relevant coupling is vibronic in origin and the temperature involved is the environmental temperature T. Explicitly, the transition rates kj0 j = kj0 rj from state j to j0 are given by k01 ¼ k34  ~kL ¼ νL~f ðxL Þ

ð1Þ

k10 ¼ k43  kL ¼ νL f ðxL Þ

ð2Þ

k12

¼ k45  ~kS þ ~knr ¼ νS ð1 þ nS ðxS ÞÞ þ νnr ð1 þ nnr ðxnr ÞÞ

k21 ¼ k54  kS þ knr ¼ νS nS ðxS Þ þ νnr nnr ðxnr Þ

k23  kDA ¼ νDA f ðxDA Þ

ð6Þ

k03 ¼ k14 ¼ k25  ~kR ¼ νR~f ðxR Þ

ð7Þ

k30 ¼ k41 ¼ k52  kR ¼ νR f ðxR Þ

ð8Þ

In these equations f(x) = 1/[exp(x) + 1] and ~f (x)  1f(x), x L = (ε D1  μ L )/k B T, x R = (ε~A2  μ R )/k B T, and x DA = (εD2  ~εA2  VC0 )/kBT. The rate coefficients ν are determined by the corresponding couplings. Following ref 7, the transition rates between the HOMO and LUMO in the donor phase are assigned by using the boson population factors ns = 1/[exp(xs)  1] and nnr = 1/[exp(xnr)  1] with scaled energies xS = ΔED/kBTS and xnr = ΔED/kBT. ~kL  k01 = k34 is the rate to move an electron

ð10Þ

dP2 ðtÞ ¼ k21 P1 ðtÞ þ k23 P3 ðtÞ þ k25 P5 ðtÞ dt  ðk12 þ k32 þ k52 ÞP2 ðtÞ

ð11Þ

dP3 ðtÞ ¼ k30 P0 ðtÞ þ k32 P2 ðtÞ þ k34 P4 ðtÞ dt  ðk03 þ k23 þ k43 ÞP3 ðtÞ

ð12Þ

dP4 ðtÞ ¼ k43 P3 ðtÞ þ k41 P1 ðtÞ þ k45 P5 ðtÞ dt  ðk34 þ k14 þ k54 ÞP4 ðtÞ

ð13Þ

P5 ðtÞ ¼ 1 

4

∑ PjðtÞ j¼0

ð14Þ

In terms of these probabilities electron currents can be expressed as

ð4Þ ð5Þ

k32

dP1 ðtÞ ¼ k10 P0 ðtÞ þ k14 P4 ðtÞ þ k12 P2 ðtÞ dt  ðk01 þ k41 þ k21 ÞP1 ðtÞ

and normalization implies that

ð3Þ

 ~kDA ¼ νDA~f ðxDA Þ

ð9Þ

JL ðtÞ ¼ kL ðP0 þ P3 Þ  ~kL ðP1 þ P4 Þ

ð15Þ

JR ðtÞ ¼ ~kR ðP3 þ P4 þ P5 Þ  kR ðP0 þ P1 þ P2 Þ

ð16Þ

JS ðtÞ ¼ kS ðP1 þ P4 Þ  ~kS ðP2 þ P5 Þ

ð17Þ

Jnr ðtÞ ¼ knr ðP1 þ P4 Þ  ~knr ðP2 þ P5 Þ

ð18Þ

JDA ðtÞ ¼ ~kDA P2  kDA P3

ð19Þ

JL (JR) is the current entering (leaving) the molecular system from (to) the electrodes, JS and Jnr are, respectively, the lightinduced and nonradiative transition currents between the HOMO and the LUMO in the donor phase, and JDA is the average current between the donor and acceptor species. Below we will focus on the steady-state magnitude, JL = JR = JDA = JS + Jnr = J, of these currents. The time evolution and steady-state currents associated with this kinetic model can be evaluated exactly; however, such exact solution becomes costly for a larger, more realistic system that takes into account also transport within the donor and acceptor 21398

dx.doi.org/10.1021/jp205856x |J. Phys. Chem. C 2011, 115, 21396–21401

The Journal of Physical Chemistry C

ARTICLE

phases. We therefore advance also an approximate mean-field treatment and show that it can provide a good approximation to the exact analysis and can be used for realistic multilevel systems at a relatively low computational cost. To this end, we introduce the averaged site occupations pD1(t)  ÆnD1æ = P1(t) + P4(t), pD2(t)  ÆnD2æ = P2(t) + P5(t), and pA2(t)  ÆnA2æ = P3(t) + P4(t) + P5(t). (See also the illustration in Figure 2.) Therefore, the currents eqs 1519 can be rewritten as follows JL ðtÞ ¼ kL ð~pD1  pD2 Þ  ~kL pD1

ð20Þ

JR ðtÞ ¼ ~kR pA2  kR ~pA2

ð21Þ

JS ðtÞ ¼ kS pD1  ~kS pD2

ð22Þ

Jnr ðtÞ ¼ knr pD1  ~knr pD2

ð23Þ

where ~p = 1  p. The treatment of the average current JDA(t) between the donor and acceptor species is more difficult. In terms of occupation number, JDA(t) is JDA ðtÞ ¼ ~kDA ÆnD2 ð1  nA2 Þæ  kDA Æð1  nD1  nD2 ÞnA2 æ ð24Þ Neglecting fluctuations, that is, ÆnD1nA2æ ≈ ÆnD1æÆnA2æ = pD1pA2 and ÆnD2nA2æ ≈ ÆnD2æÆnA2æ = pD2pA2, leads to the mean-field expression of the current MF ðtÞ ¼ ~kDA pD2 ~pA2  kDA ð~pD1  pD2 ÞpA2 JDA

ð25Þ

As a consequence, we arrive at the following mean-field rate equations for the averaged site occupations dpD1 ¼ JL ðtÞ  JS ðtÞ  Jnr ðtÞ dt

ð26Þ

dpD2 MF ¼ JS ðtÞ þ Jnr ðtÞ  JDA ðtÞ dt

ð27Þ

dpA2 MF ¼ JDA ðtÞ  JR ðtÞ dt

ð28Þ

The full kinetics in this approximation is obtained by solving eqs 2628 together with eqs 20, 23, and 25 self-consistently. Note that the number of coupled equations solved in this scheme grows linearly with the number of N of single electron states, whereas in the exact approach this number is essentially the number of molecular states ∼2N. To illustrate the nature of the kinetics that results from these rate processes, we choose a set of physically reasonable parameters. In the calculation discussed below, the following choice was used: μL = 0.0 eV, μR = μL + |e|U, εD1 = 0.1 eV, εD2 = 1.4 eV, εA2 = 0.9 eV, VC = 0.25 eV, and VC0 = 0.15 eV. Therefore, ΔED = εD2  εD1 = 1.5 eV19 and VC + VC 0 = 0.4 eV.20,21 For the temperatures we take T = 300 K and Ts = 6000 K. The kinetic rates are set to νL = νR = νS = νnr = 0.01νDA and νDA = 1012 s1, describing a system with efficient and fast donor-to-acceptor electron transfer (which can occur on the picosecond time scale22) and moderate radiationless losses, as would be used in such applications. Finally, note that in the particular example employed here we have considered a situation where the imposed potential bias falls between the acceptor species and the right electrode. It

Figure 3. Current (J, left vertical axis) and power (P = UJ, right vertical axis) in the PV cell, plotted against the voltage bias U (see text for parameters). Plot (a) compares results from the exact calculation to those obtained from mean-field approximation. Plot (b) compares the same exact results (νnr = 0.01νDA) as those obtained for the ideal cell for which νnr = 0. We assume that νDA = 1012 s1.

should be emphasized that although the results shown in Figures 3 and 4 are based on these choices, the qualitative behavior discussed below holds for a wide range of these parameters.

’ RESULTS AND DISCUSSIONS Figure 3 shows results for the stationary donor f acceptor current obtained from both the exact solution from eqs 919 and the mean-field approximation, eqs 2028. Figure 3a compares the results of the mean-field approach to their exact counterpart, showing that the former provides a good approximation to the exact behavior. Figure 3b compares the performance of a junction characterized by the prescribed parameters to the corresponding ideal junction in which nonradiative losses are absent (νnr = 0). In both cases, the current is constant until the electrochemical potential on the right electrode comes within ∼kBT of the acceptor level A2 and decreases sharply after it exceeds this level. Consequently, the generated power, P(U) = UJ(U), goes through a sharp maximum, Pmax = UmaxJ(Umax), in that voltage region. Next, consider the efficiency. The maximal power conversion efficiency is defined by η¼

Pmax Umax JðUmax Þ ¼ PS PS

ð29Þ

where PS is the incident radiant power, a constant independent of the process undergone by the system. The thermodynamic efficiency at maximum power is given by   Pmax Umax JðUmax Þ Umax Jnr ðUmax Þ ¼ ¼ 1 þ η  ΔED JS ðUmax Þ JS ðUmax Þ ΔED Q_ S ð30Þ 21399

dx.doi.org/10.1021/jp205856x |J. Phys. Chem. C 2011, 115, 21396–21401

The Journal of Physical Chemistry C

ARTICLE

Finally, consider again the performance of the mean-field approximation relative to the exact solution. As seen from Figures 3 and 4, the mean-field treatment provides a good approximation that closely follows the behavior of exact solutions. The influence of correlations is particularly seen in Figure 4b, where we find small but noticeable differences between the mean-field and the exact curves for Δε beyond the maximum at ∼0.4 eV.

Figure 4. (a) Power conversion efficiency η and (b) thermodynamic efficiency η* evaluated at maximum power and displayed as functions of the interface gap Δε. Mean-field results are compared with the exact solutions of the underlying master equation. Parameters are the same as those in Figure 3 with the difference that εA2 runs from 1.4 to 0.4 eV, and μR is determined by Pmax. For the power, P = PS incident on the cell, we assume 1.0 nW.24

where Q_ S is the net energy absorbed per unit time from the radiation field, that is, heat absorbed from the hot reservoir, Q_ S = ΔEDJS. We note in passing that all processes undergone by our system are accompanied by well-defined energy changes: The heat fluxes associated with the electron exchange processes between system and leads, are, in the present model Q_ L = (εD1  μL)JL , Q_ R = (μR  εA2)JR, and Q_ nr = ΔEDJnr is the net heat generation per unit time related to nonradiative relaxation processes, and Q_ DA = ΔεJDA is the heat flux associated with the electron transfer at the DA interface. Energy conservation implies that the overall cell power is the sum of these fluxes, that is, P = Q_ L + Q_ R + Q_ S + Q_ nr + Q_ DA  (μR  μL)J = UJ. Of central importance is the dependence of the efficiency on the interface LUMOLUMO energy gap Δε. One may intuitively expect to find that an optimal value of this parameter exists: A finite Δε is needed to drive the charge separation process, but a larger Δε implies that more energy may be lost to unproductive processes. Equations 29 and 30 quantify this phenomenon, which is illustrated in Figure 4. Figure 4a shows the power conversion efficiency calculated for the chosen parameter set using eq 29. For comparison, the corresponding result for the ideal cell (νnr = 0) is also shown. Both are seen to go through a maximum as functions of the interfacial LUMOLUMO gap Δε. The thermodynamic efficiency, eq 30, displayed against Δε in Figure 4b shows a similar pronounced maximum; however, the ideal thermodynamic efficiency is a monotonously decreasing function of Δε. Note that the ideal cell efficiency is an upper bound to the actual efficiency; however, for this finite power operation, it is below the Carnot efficiency, ηC = 1  T/TS = 0.95.

’ CONCLUSIONS In summary, the effort to increase and optimize the efficiency of heterojunction OPVs necessarily involves many structural and energetics system parameters. The above considerations focus on what is arguably the most important generic issue  the optimization of the interfacial LUMOLUMO gap that compensates between the need to overcome the exciton binding energy and the required minimization of losses. For the present simplified model and our choice of parameters, we find the most efficient setup for interface gap energies somewhat above 0.4 eV. More important is the fact that the present model, with future generalizations that should include transport in the donor and acceptor phases and polaronic relaxation following redistribution of charge densities, provides a framework for analyzing such efficiency measures. The mean-field approach introduced here provides a reliable approximation that can be used for fast evaluation of more complex model systems and will be useful in extending these studies to realistic OPV cell models. A more ambitious task would be to generalize the concept advanced in the Article to the quantum regime. Consideration of quantum effects and coherence (see, for example, ref 23) may prove useful in the discussion of fundamental limits to photovoltaic efficiency. ’ AUTHOR INFORMATION Corresponding Author

*E-mail: [email protected]; [email protected].

’ ACKNOWLEDGMENT We thank Prof. Mark Ratner for helpful discussions. M.E. gratefully acknowledges funding by a Forschungsstipendium by the Deutsche Forschungsgemeinschaft (DFG, grant number EI 859/1-1). The research of A.N. is supported by the Israel Science Foundation, the Israel-US Binational Science Foundation, the European Science Council (FP7/ERC grant no. 226628), and the Israel - Niedersachsen Research Fund. ’ REFERENCES (1) Deibel, C.; Dyakonov, V. Rep. Prog. Phys. 2010, 73, 096401. (2) Nicholson, P. G.; Castro, F. A. Nanotechnology 2010, 21, 492001. (3) Sariciftci, N. S.; Smilowitz, L.; Heeger, A. J.; Wudl, F. Science 1992, 258, 1474–1476. (4) Yu, G.; Gao, J.; Hummelen, J. C.; Wudl, F.; Heeger, A. J. Science 1995, 270, 1789–1791. (5) Hoppe, H.; Sariciftci, N. S. J. Mater. Res. 2004, 19, 1924–1945. (6) Koeppe, R.; Sariciftci, N. S. Photochem. Photobiol. Sci. 2006, 5, 1122–1131. (7) Rutten, B.; Esposito, M.; Cleuren, B. Phys. Rev. B 2009, 80, 235122. (8) Giebink, N. C.; Wiederrecht, G. P.; Wasielewski, M. R.; Forrest, S. R. Phys. Rev. B 2011, 83, 195326. (9) Potscavage, W. J.; Sharma, A.; Kippelen, B. Acc. Chem. Res. 2009, 42, 1758–1767. 21400

dx.doi.org/10.1021/jp205856x |J. Phys. Chem. C 2011, 115, 21396–21401

The Journal of Physical Chemistry C

ARTICLE

(10) Einax, M.; Solomon, G. C.; Dieterich, W.; Nitzan, A. J. Chem. Phys. 2010, 133, 054102. (11) Einax, M.; K€orner, M.; Maass, P.; Nitzan, A. Phys. Chem. Chem. Phys. 2010, 12, 645–654. (12) Dierl, M.; Maass, P.; Einax, M. Europhys. Lett. 2011, 93, 50003. (13) Sylvester-Hvid, K. O.; Rettrup, S.; Ratner, M. A. J. Phys. Chem. B 2004, 108, 4296–4307. (14) Nelson, J.; Kirkpatrick, J.; Ravirajan, P. Phys. Rev. B 2004, 69, 035337. (15) Burlakov, V. M.; Kawata, K.; Assender, H. E.; Briggs, G. A. D.; Ruseckas, A.; Samuel, I. D. W. Phys. Rev. B 2005, 72, 075206. (16) Lei, B.; Yao, Y.; Kumar, A.; Yang, Y.; Ozolins, V. J. Appl. Phys. 2008, 104, 024504. (17) Wagenpfahl, A.; Deibel, C.; Dyakonov, V. IEEE J. Sel. Top. Quantum Electron. 2010, 16, 1759–1763. (18) Arkhipov, V. I.; Emelianova, E. V.; B€assler, H. Phys. Rev. Lett. 1999, 82, 1321–1324. (19) Soci, C.; Hwang, I.-W.; Moses, D.; Zhu, Z.; Waller, D.; Gaudiana, R.; Brabec, C. J.; Heeger, A. J. Adv. Funct. Mater. 2007, 17, 632–636. (20) Gregg, B. A.; Hanna, M. C. J. Appl. Phys. 2003, 93, 3605–3614. (21) Pensack, R. D.; Asbury, J. B. J. Phys. Chem. Lett. 2010, 1, 2255– 2263. (22) Rice, M. J.; Gartstein, Y. N. Phys. Rev. B 1996, 53, 10764–10770. (23) Scully, M. O. Phys. Rev. Lett. 2010, 104, 207701. (24) We take air mass 1.5 under standard test conditions (corresponds to 1000 Wm2) and assuming an illuminated area of 1 μm2.

21401

dx.doi.org/10.1021/jp205856x |J. Phys. Chem. C 2011, 115, 21396–21401