High-Temperature Heat Contents of Aluminum Oxide, Aluminum

undertaken at the Pacific Experiment Station of the Bureau of Mines. High-temperature heat- content data are especially necessary for the ac- curate c...
2 downloads 0 Views 476KB Size
72 [COhTRIBUTION FROM T H E

C. HOWARDSIIOMATE A N D B. F. NAYLOR WESTERN REGION,BUREAC OF

Vol. 67

UNITED STATES DEPARTMENT OF

MINES,

THE

INTERIOR j

High-Temperature Heat Contents of Aluminum Oxide, Aluminum Sulfate, Potassium Sulfate, Ammonium Sulfate and Ammonium Bisulfate1 BY C. HOWARD SHOMATE~ AND B. F. NAY LOR^ A study of the thermodynamic properties of many of the compounds involved in the preparation of alumina from clays and alunite has been undertaken at the Pacific Experiment Station of the Bureau of Mines. High-temperature heatcontent data are especially necessary for the accurate calculation of equilibria and heat balances for metallurgical processes at elevated temperatures. Data of this type are lacking in a large number of instances; accordingly this paper presents such data for aluminum oxide, anhydrous aluminum sulfate, potassium sulfate, ammonium sulfate and ammonium bisulfate. Method and Materials

TABLE I HIGH-TEMPERATURE HEATCONTENTS OF AlpOa Mol. wt. = 101.94 H T - z'flo1.18 H T - HWa.16,

Temp.,

OK.

462.6 508.6 651.8 657.3 725.1 896.6 920.5 1119.8

cal./mole

Temp.,

3,670 4,820 8,660 8,800 10,680 15,660 16,350 22,330

cal./mole

OK.

1129.6 1318.1 1346.8 1510.0 1562.9 1660.2 1787.4

22,630 28,370 29,250 34,300 35,930 38,880 42,780

TABLE I1 The high-temperature heat contents were determined by HIGH-TEMPERATURE HEATCONTENTS OF A&(SOd)s the "drop" method in a previously described a p p a r a t ~ s . ~ = 342.12 Mol. wt. The calorimeter was electrically calibrated, using the deHT HSS.18, HT - Hru.ie, fined calorie (1 cal. = 4.1833 Int. joules). Each sample Temp.. O K . cal./molc Temp., O K . cal./mole was enclosed in a platinum-rhodium alloy capsule whose 475.7 13,020 936.8 55,130 heat content had been determined previously. For the aluminum oxide, aluminum sulfate, and potassium sulfate 568.5 21,390 978.1 59,840 an unsealed capsule w a s used, while a gold-sealed capsule 661.2 29,270 1025.4 64,540 was employed for the ammonium sulfate and ammonium 747.9 37,490 1072.5 69,110 bisulfate measurements. 812.9 43,990 1106.5 72,420 The aluminum oxide sample consisted of natural, almost colorless sapphires selected from a sample previously used 882.7 50,960 by Parks and Kelley4 for low-temperature specific-heat measurements. They were crushed and screened before TABLE I11 using. Within the limits of experimental error, the sample HIGH-TEMPERATURE HEATCONTENTS OF K&O+ analyzed 100.0% Alto8. Recrystallized reagent grade aluminum sulfate octodecaMol. wt. = 174.252 hydrate was used to prepare anhydrous aluminum sulfate. Teomp., HT HZIB.IS, Temp., HT Has.18, OK. cal./molc cal./mole K. The water of crystallization was removed by drying a t 200' under reduced pressure for eight hours and then, at 5,700 1078.5 35,230 462.4 gradually increasing temperatures up to 450 in a stream 9,650 1143.1 38,360 563.4 of dry air for approximately two hundred hours. Analysis 1258.8 44,350 669.9 14,060 showed 29.78% &Os (theoretical 29.80%) and 0.2% HeO. 1316.3 47,710 (premelt.) The potassium sulfate was a portion of the sample which 741.8 17,300 had been previously used by Moore and Kellep for low1337.3 49,240 (premelt.) 808.7 20,580 temperature specific heat measurements and carefully pre23,670 (pretran.) 1358.6 58,230 853.1 served. Previous analysis for sulfate had shown the ma1461.9 63,250 872.4 25,620 terial to be at least 99.7% pure. Reagent grade ammonium sulfate was heated at 75" 1475.2 63,780 889.6 26,420 for several days. Analysis for sulfate gave 72.6% SO, 932.4 28,500 1578.8 68,840 (theoretical 72.73%). 1698.0 74,240 32,560 1020,4 The ammonium bisulfate was reagent grade material which was dried at 130' for several days. Titration with TABLE V TABLE IV standard alkali gave 0.877% acid H (theoretical 0.87670) and analysis for sulfate, 83.5% so4 (theoretical 83.45%). HIGH-TEMPERATURE HEAT HIGH-TEMPERATURE HEAT OF NHdHSO4 CONTENTS OF (NH4)1SOI CONTENTS Results Mol. wt. = 116.108 Mol. wt. =, 132.14 The experimentally determined heat contents

-

-

-

O,

above 298.16OK. of aluminum oxide, aluminum sulfate, potassium sulfate, ammonium sulfate and ammonium bisulfate are given in Tables I, 11,111, IV and V. The heat content values for aluminum sulfate have been corrected for the water impur(1) Published by permission of the Director, Bureau of Mine,. U S Department of the Interior. X o t copSrighied (2) Chemist, Pacific Experiment Station, Bureau of hliiie. ' 7 ) J C Southard. Tms J O U R ~ A L 63, 31 LZ (I'M11 14) G S Parks und K K Kelley, J P h y s Lhem , SO, 47 ( I Y 2 6 ) ( 5 ) G . E. Moore and K K Kelley, Tina J O U R N A I , 64,2949 (1942)

Temp., OK.

402.1 441.2 482.8 551.5 594.:% ti."

(i

-

Temp.,

HT tlZPD16, cal./mole

OK.

RT

- am.11,

cal./mole

5,080 7,090 9,350 13,490

354.6 373.0 380.9 397.7

2,050

16,180 19.5fil) (dw

420.7 451. 0

8,210 S,(i90

505.4

18,500 1 ti, 1111

!

5ti9, 5 ti32.2

2,840 3,080 3,840

19.52~lirlec.)

Jan., 1945

HEATCONTENTS OF ALUMINUM, POTASSIUM AND AMMONIUM SALTS

73

TABLE VI HEATCONTENTS, ENTROPIES, AND FREEENERGIES ABOVE 298.16’K. A1201

T

OK.

400 500 600 700 800

856 856 900 1000 1100 1200 1300 1342 1342 1400 1500 1600 1700 1800

ST - Szos.16, HT - H298.i6. cal./deg./ FT

.-

- Fms.ia, cal./mole

cal./mole

mole

2,175 4,600 7,200 10,000 13,030

6.27 11.67 16.41 20.72 24.76

- 1,610 - 3,760 - 6,420 - 9,530

16,050 18,890 21,760 24,740 27,800

28.33 31.32 34.05 36.64 39.09

16,970 -21,200 -25,,720 -30,500 -35,540

30,890 33,980 37,070 40,110 43,120

41.38 43.51 45.51 47.35 49.07

-40,820 -46,310 - 52,020 -57,910 63,980

- 13,050

-

KaSOi

A1z(SOda

- Hzos.ia, cat./mole

HT

ST

-

S238.16

cal./deg./ ’ FT - Fm.io, mole cal./mole

7,160 15,220 23,820 32,880 42,690

20.55 38.76 54.41 68.36 81.45

- 6,880 - 15,700 -26,090

52,650 62,020 71,790

93.19 103.06 112.37

-65,650 -81,180 -97,680

-37,960 -51,180

-

ity previously mentioned. The values marked “(pretran.)” or “(premelt.)” are considered to involve pretransition or premelting effects. Evidence of decomposition was observed for those runs marked “(dec.)” and measurements were then discontinued. All molecular weights accord with the 1941 International Atomic Weights. Determinations were made from temperatures as low as 354’K. in the case of ammonium bisulfate to as high as 1773’K. for aluminum oxide. With all samples, except aluminum oxide, measurements were extended to the point where decomposition occurred, as evidenced by loss in weight of the capsule and contents. The heat contents are represented graphically in Fig. 1. Aluminum oxide, aluminum sulfate and ammonium sulfate yield smooth curves with no discernible discontinuities. Both potassium sulfate and ammonium bisulfate exhibit sharp melting points, the premelting being only slight for the former and negligible a t 20’ below the melting point of the latter. The heats of fusion calculated from the heat content data were found to be 8,760 calories at 1,342’R. and 3,420 calories a t 417’K., respectively. Potassium sulfate has a transition with a heat effect of 1,940 calories a t 856’K. This transition has been observed by Roberts6 and by Hiittner and Tammann.’ The data of &me other investigators, to be discussed below, have also been plotted in the case of aluminum oxide. In Table VI the heat contents read a t 100’ intervals from the smooth curves through the data for aluminum oxide, aluminum sulfate and potassium sulfate have been listed. The cor(6) H. S. Roberts, Am. J . Sci., SSA, 273 (1938) (7) K.HUttner and G. Tammaan, Z.anorp. Chcm., *t. 215 (19041906).

ST - sos.16,

HT - Hos.10, cal./deg./ cal./mole

mole

3,400 7,110 11,130 15,390 20,100 22,86O(a) 24,80o(i3 26,950 3 1,630 36,250 41,210 46,390 48,660(8) 57,420(1) 60,210 65,070 69,840 74,330

9.79 18.17 25.49 32.05 38.33 41.67 43.93 46.39 51.32 55.72 60.04 64.18 65.90 72.43 74.46 77.82 80.89 83.62

FT -

Fm1.18,

cal./mole

-

4,790 10,450 - 16,840 7 23,920 31,640 36,240 36,240 40,080 49,170 58,720 68,720 79,120 83,620 83,620 90,310 102,140 114,260 126,700

-

-

responding graphically computed entropy increments and the free energy changes above 298.16’ K. also are included. Table VI1 is a similar compilation for ammonium sulfate and ammonium bisulfate, except that the data have been listed at 50’ intervals. For calculating the free energy values the following molal entropies a t 298.16’ K. were used: aluminum oxide, 12.5*; aluminum I

I

lo00

1400

80,000

200

800

I

1800

T,OK. Fig. 1.-Heat contents above 298.16’K.: this work, 0; Auzhbikovich, A ; Gronow and Schwiete, 8 ; Newman and Brown, e; Wilkes 0 . (8) IC.

P.Yelley, Burmu of Minu Bullda 484, 1941.

1111 pp.

C. HOWARD SHOMATE AND B. F. NAYLOR

74

sulfate, b7.29; potassium sulfate, 42.06; and ammonium sulfate, 52.6.9 No entropy value has been reported for ammonium bisulfate.

Vol. 67

these temperatures. Frequent calibrations of the thermocouple were made a t the gold and palladium points in the manner described by South-

TABLE VI1 HEATCONTENTS, ENTROPIES, AND FREEENERGIES ABOVE 29x.16°K.

Of the five compounds investigated, there appear to be pertinent heat content data only for aluminum oxide. Gronow and Schwiete,'O (NHdnSO4T------NH~HSO~Wilkes," and Miehr, Immke and Kratzert,12have ST ST HT szos 16 SB8.18, made measurements to temperatures as high as T Hzoa 16, cal./de& FT - Fnr.18, H T - Hm.18,cal /dcg./ those reached in this study. The results of OK. cal./mole mole cal./mole cal./mole mole Gronow and Schwiete check the present work very 350 2,510 7 . 7 8 - 2,940 1,880 5 81 well; those of Wilkes are lower by approximately 4.00 4,970 14.35 - 6,130 3,900 11.20 370, while those of Miehr and co-workers (not 417 4,620(s) 12.96 plotted) are erratic and higher by about 1%. 417 8,040(1) 21.16 Also Newman and Brown13 and Au~hbikovichl~ 450 7,570 20.46 - 9,620 9,650 24.88 have reported measurements to 1300'K. and 500 10,340 26.30 -13,430 12,220 30.29 1400°K., respectively. The results of the former 550 13,380 32.09 -17,520 15,000 35.58 differ from the present work on the average by 600 16,590 37.67 -21,890 17,940 40.70 0.570, while those of the latter deviate by about Heat content equations have been derived from 1% in the lower temperature range and are in exthe experimental data and the following specific cellent agreement at higher temperatures. heat values at 298.16OK.: aluminum oxide, The heat content of a sample of aluminum oxide 18.814; aluminum sulfate, 62.009; potassium prepared by ignition of aluminum sulfate also sulfate, 31.0g6; and ammonium sulfate, 44.8l9 was determined a t several temperatures during cal. per deg. per mole, respectively. The appro- the course of the present work. However, the priate temperature range and the mean percentage weight of sample used was limited by the small deviation of the heat content equation from the apparent density and corrections for the moisture experimental data are indicated after each equa- impurity were uncertain, especially at high temtion. peratures; hence the results were somewhat erratic and not as reliable as those for the sapAllO#(s): HT - Hns.16 = 27.43T 0.00153T' 847,OoO/T 11,155 (298'-1800%.; 0.4%) phires. In general, a slightly higher heat content was indicated. Al,(SO4)r(s): HT Hzps.18 = 88.09T 0.00740T' 2,712,000/T - 36,020 (298"11OO'K.; 0.7%) The transition temperature and melting point KzSOd(a): HT - Hn0s.l~ = 27.43T 0.01276P of potassium sulfate, 856'K. and 1,342'K., re352,000/T - 10,494 (298"-856'K.; 0.4%) spectively, used in this paper are those reported KtSOd(B): HT - Hn06.16 = 26.80T + 0.01005T' - 5,335 by R o b e r t ~ . ~ The melting point of the am(856'-1342 O K . ; 0.2%) monium bisulfate sample was found experiK&O4(1): HT - Hm.18 47.28T - 5,938 (1342'0.5'K. 1700'K.; 0.1%) mentally by cooling rates to be 417 Kendall and Davidsonl5 have reported 420.1 f (NHI)%%(S): HT - Hm.16 = 24.773 0.0336T' 10,372 (298°-6000K.; 0.8%) 0.5'K. for the melting point. r

-

+ + +

-

+ + +

f

+

N"~HSO~(S): HT - Hn08.16

NH,HSO4(1): HT - Hm.16

+

-

+

-

1O.OOT 0.0405T' 6,582 (298'417 "K.; 1.0%) = 16.06T 0.0374T' 5,160 (417°-6000K.;0.47,)

Differentiating the above heat content equations gives the following specific heat relationships

+ +

Al*Os(s): C, a 27.43 0.00306T 847,000/T3 Alz(SO4)s(~): C p = 88.09 4-0.01480T 2,712.000/'Tt K z % l ~ ( a ) cp : m.43 0.02552T 3 5 2 , W / P K&Od(B): C p 26.80 0.02010T K&O,(I): C p 47.28 ("&SO&): C p 24.77 0.0672T N H l f l S o l ( ~ ) :Cp a 10.00 O.0810T NH4HSO(I): C p = 16.06 0.0748T

--

+

+ + +

Discussion In the present study the maximum error involved in measuring the temperature of the capsule and its contents in the furnace has been estimated as varying from 0 . 5 O at 400'K. to 3' at 1800°K., corresponding to errors of 0.5 and 0.2%, respectively, in the heat content values at ( 0 ) C . H. Shomatc, unpublished data,

summary The high-temperature heat contents, above 298.16'K., of aluminum oxide (sapphire), anhydrous aluminum sulfate, potassium sulfate, ammonium sulfate and ammonium bisulfate were determined from about 473'K. to temperatures between 623 to 1773'K., depending on the thermal stability of the substance. The heats of fusion of potassium sulfate and ammonium bisulfate and the heat of the transition in potassium sulfate have been obtained from these data. Heat content and specific heat equations, adequately representing the experimental data, have been derived for each substance. The data also (10) H. E. v. Gronow and H E. Schwiete, Z . anorp. allgem. Chcm., 186 (1933). (111 G. B. Wilkes. J . A m . Ceram. SOL, 16, 72 (1932). (12) W. Miehr, H. Immke and 1. Kratzert, ?'onind.-Ztg, 10, 1791

as,

(1926). (13) A. B. Ncwman and C . G. Brown, Ind. En& C h r m , 28, 995 (1930). (14) A. E. Aushbikovich. Lcgkie M e l d . . 8 , No. 11, 23 (1938). (16) J. Kcadnll nnd A. Davidson, I d . BUI. Cham., 11,303 (1921).

Jan., 1945

PROPERTIES OF VANADIUM TETRACHLORIDE

have been summarized by giving the heat content, entropy and free energy increments

75

above 298.16'K. at even temperature intervals. BERKELEY, CALIF.

RECEIVED AUGUST7 , 1944

[CONTRIBUTION FROM THE SCHOOL OF CHEMISTRY AND PHYSICS OF THE PENNSYL-VANIA STATE COLLEGE]

Properties of Vanadium Tetrachloride BY J. H. SIMONS AND M. G. POWELL Vanadium tetrachloride is an inorganic compound of interesting properties. It is a dark red liquid which hydrolyzes readily, which decomposes slowly a t oidinary temperatures to chlorine and the trichloride, and which reacts as a chlorinating agent. It is non-salt-like in character, has a low dielectric constant, is soluble in carbon tetrachloride, has a liquid range from -26 to 152' a t atmospheric pressure and has a relatively low boiling point, Its valence is unexpected in view of the existence of the tri- and penta-fluorides, and the non-existence of a tetrafluoride. It is an odd molecule, if the formula VC14 is correct; and its intense color may be used as supporting evidence of the free radical assumption. Vanadium tetrachloride was prepared by Roscoel by the reaction of chlorine on vanadium or vanadium nitride at red heat. From the analysis of his product and the determined vapor density, he assigned the formula VClr to the compound. He found the liquid density to be 1.8584 g./cc. a t O', 1.8363 a t 8') and 1.8159 at 30'. He was unable to obtain the pentachloride by the reaction of the tetrachloride with chlorine. He found its boiling point to be 154' at 760 mm. pressure. Biltz and Kuenecke* found the boiling point to be 148.5' a t 755 mm. pressure, and Ruff and Lickfett3 report 153.7' at 768 mm. pressure. The freezing point was found by Biltz and Kuenecke2 to be -log', but Morette4 obtained the value of -28 * 2'. Voigt and Biltz6 found the electrical conductivity to be too small to measure. Loomis and Schlundt6determined the dielectric constant a t room temperature. Their average value was 3.05. From a series of therniochemical reactions Ruff and Friedrich' concluded the heats of formation of the chlorides of vanadium to be

+

V(s) V(s) V(s)

+ Clpfg) = VC12(s)+ 147 * 4 kcal. + 3/2 C12(g) = VC13(s) + 187 * 8 kcal. + 2Clz(g) = VCL(1) + 165 * 4 kcal.

From this the following equation for the decomposition of vanadium chloride results 2VCl4)

+2VCl~(s)+ Clr(g) + 44 * 20 kcal.

(1) Roscoe, A n n . Chcm., Supplement 1, 70 (1869). (2) Biltz and Kuenecke, Z. artorg. allgem. Chcm., 141, 171.(1025). (3) Ruff and Lickfett, B e r . , 44, 506 (1011). (4) Morette, Comfit. rend., 202, 1846 (1936). ( 5 ) Voigt and Biltz, 2 anorg. allgcm. Chcm.. 133, 277 (1924). (6) Loomis and Schlundt, J . P h y s . Chcm., 9, 734 (1915). (7) Ruff and Friedrich, Z . anorg. allgcm. Chem., 89, 279 (1914).

Preparation.-Vanadium tetrachloride was prepared by a modification of the method given by Mentes.' Dry chlorine was passed over ferro-vanadium contained in a glass combustion tube in an electric furnace. Onequarter-inch mesh ferro-vanadium containing 90% vanadium was used. The entering chlorine passed through a pair of sulfuric acid bubblers for the purpose of drying. The product from the exit side of the combusion tube was received in a 500-cc. flask. This was the part of an allglass fractionating column which contained no stopcock and its attendant grease.* On the take-off of the fractionating column was sealed a small condenser and a fraction cutter. This fraction cutter had a number of 50-cc. flasks sealed onto it to receive the fractions. Each of these receivers was provided with a side arm containing an internal capillary for breaking off purposes. Rotation of the fraction cutter on a ground joint provided a means of directing the liquid stream into the different receivers. The entire apparatus was sealed together so that the product came in contact onlv with dass. The temperature of ;he rea&on tube was adjusted to 200'. This is a lower temperature than has been previously used but was employed to reduce the amount of ferric chloride in the product. At the end of the reaction, the connectioa between the reaction tube and receiver was sealed, and the product was distilled. The receivers were sealed off from the fraction cutter after they were filled. The samples collected boiled at 149.7' at a pressure of 731 mm. These samples were found to remain in a satisfactory condition for several months without appreciable decomposition, if kept in the dark. Vanadium trichloride was prepared from vanadium tetrachloride by heating it a t 140' for one week, while passing dry carbon dioxide over it. The vanadium trichloride was dried by heating it a t 160" for three days. I t was analyzed for vanadium by titrating with potassium permanganate and found to contain 32.30%. The theoretical is 32.39%. A gravimetric analysis for chlorine gave 67.10%, while the theoretical is 67.61Cj,. The Equilibrium Constant for the Reaction 2VC&(s) CL(g) S 2VClr(g).-The equilibrium constant for this reaction was determined by subjecting a sample of vanadium trichloride to a known volume of chlorine and determining the increase in pressure when equilibrium was attained. A diagram of the apparatus used is shown in Fig. 1. This consisted essentially of a reaction vessel containing a boat of vanadium trichloride in an electric furnace. This was connected with capillary tubing to a U-tube of sulfuric acid which in turn was connected to an adjustable mercury manometer. The sulfuric acid U-tube was calibrated in cubic centimeters. As the apparatus was originally sealed together, the reaction vessel was open a t the end opposite the capillary tubing. A stream of dry nitrogen was passed through the apparatus. A sample of vanadium trichloride was transferred to a small porcelain boat, the operation being performed in a dry box. I t was placed in a glass tube and transported in an atmosphere of dry nitrogen. After introduction of the porcelain boat, the end of the reaction tube was drawn out to form a capillary, using care to pre-

+

(8) Mentes, THIS J O U R N A L , 36, 671 (1913). (9) Simoos, I n d . E n g Chcm , A d . Ed., 10,29 (1938)