In Situ Sensor Technology for Simultaneous ... - ACS Publications

Feb 26, 2015 - Department of Marine Chemistry and Geochemistry, Woods Hole Oceanographic Institution, McLean 203, MS #8, 266 Woods. Hole Road ...
3 downloads 0 Views 1MB Size
Subscriber access provided by Otterbein University

Article

An In-situ Sensor Technology for Simultaneous Spectrophotometric Measurements of Seawater Total Dissolved Inorganic Carbon and pH Zhaohui Aleck Wang, Frederick N. Sonnichsen, Albert M. Bradley, Katherine A. Hoering, Thomas M. Lanagan, Sophie N. Chu, Terence R. Hammar, and Richard Camilli Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/es504893n • Publication Date (Web): 26 Feb 2015 Downloaded from http://pubs.acs.org on March 3, 2015

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 30

Environmental Science & Technology

An In-situ Sensor Technology for Simultaneous Spectrophotometric Measurements of Seawater Total Dissolved Inorganic Carbon and pH Zhaohui Aleck Wang*1, Frederick N. Sonnichsen2, Albert M. Bradley2, Katherine A. Hoering1 Thomas M. Lanagan2, Sophie N. Chu1, Terence R. Hammar2, and Richard Camilli2 1

Department of Marine Chemistry and Geochemistry, Woods Hole Oceanographic Institution, McLean 203, MS # 8, 266 Woods Hole Road, Woods Hole, Massachusetts 02543, USA.

2

Department of Applied Ocean Physics & Engineering, Woods Hole Oceanographic Institution, 266 Woods Hole Road, Woods Hole, Massachusetts 02543, USA.

*Corresponding author Email: [email protected]; Telephone: 1-508-289-3676; Fax: 1-508-457-2183 Keywords: dissolved inorganic carbon, pH, carbon dioxide, in-situ, sensor, ocean acidification, carbon cycle, spectrophotometry, seawater

ACS Paragon Plus Environment

1

Environmental Science & Technology

1

Page 2 of 30

ABSTRACT

2

A new, in-situ sensing system, Channelized Optical System (CHANOS), was recently

3

developed to make high-resolution, simultaneous measurements of total dissolved inorganic

4

carbon (DIC) and pH in seawater. Measurements made by this single, compact sensor can fully

5

characterize the marine carbonate system. The system has a modular design to accommodate two

6

independent, but similar measurement channels for DIC and pH. Both are based on

7

spectrophotometric detection of hydrogen ion concentrations. The pH channel uses a flow-

8

through, sample-indicator mixing design to achieve near instantaneous measurements. The DIC

9

channel adapts a recently developed spectrophotometric method to achieve flow-through CO2

10

equilibration between an acidified sample and an indicator solution with a response time of only

11

~90s. During laboratory and in-situ testing, CHANOS achieved a precision of ±0.0010 and ±2.5

12

µmol kg-1 for pH and DIC, respectively. In-situ comparison tests indicated that the accuracies of

13

the pH and DIC channels over a three-week time-series deployment were ±0.0024 and ±4.1 µmol

14

kg-1, respectively. This study demonstrates that CHANOS can make in-situ, climatology-quality

15

measurements by measuring two desirable CO2 parameters, and is capable of resolving the CO2

16

system in dynamic marine environments.

17

INTRODUCTION

18

The marine carbon dioxide (CO2) system strongly influences the marine carbon cycle. It

19

helps regulate the Earth’s climate by controlling the amount of CO2 that exchanges between the

20

ocean and the atmosphere. Currently, the ocean absorbs about one quarter to one third of the

21

anthropogenic CO2 released to the atmosphere 1-3, therefore reducing the rate of atmospheric CO2

22

increase and curbing global warming. However, oceanic uptake of anthropogenic carbon is

23

causing a rapid change in seawater carbonate chemistry, a phenomena referred to as ocean

ACS Paragon Plus Environment

2

Page 3 of 30

Environmental Science & Technology

24

acidification. In ocean acidification, excess CO2 lowers seawater pH, increases total CO2

25

concentration, and decreases calcium carbonate saturation 4-5. Changes in the marine CO2 system

26

may result in complicated responses and feedbacks in the ocean including changes in the marine

27

carbon and other elemental cycles, as well as changes in marine biology and ecology 4, 6-7. Ocean

28

acidification also reduces seawater buffering capacity, which slows oceanic carbon uptake and

29

acts as a positive feedback in the increase of atmospheric CO2 3, 8.

30

Precise and accurate characterization of the marine CO2 system is critical to studying the

31

marine carbon cycle and ocean acidification. The development of in-situ sensor technologies for

32

CO2 parameters have been widely recognized as a research priority in the carbon and ocean

33

acidification research communities

34

system on various time scales ranging from minutes to decades, and spatial scales of meters to

35

kilometers. Because of the high costs associated with traditional bottle sampling, it is more

36

effective to use autonomous sensors and instruments to achieve high-resolution data 15.

9-14

. It is important to study dynamics of the marine CO2

37

The marine CO2 system is described by four measurable, primary parameters: total

38

dissolved inorganic carbon (DIC), partial pressure of CO2 (pCO2) or CO2 fugacity (fCO2), pH,

39

and total alkalinity (TA). Measurements of any two of the four parameters are required to

40

calculate the others and fully resolve the carbonate system using seawater acid-base equilibria.

41

Simultaneous measurements of two CO2 parameters are thus attractive. However, different

42

measurement pairs will generate a range of calculation errors as a result of analytical errors,

43

uncertainties in equilibrium constants, and their non-linear propagation in the calculations. Large

44

errors result when pCO2 and pH are used due to their strong co-variation 16. The errors are often

45

minimized when DIC and pH, or DIC and pCO2 are used 9. However, only in-situ pCO2 and pH

ACS Paragon Plus Environment

3

Environmental Science & Technology

17-21

46

sensors are commonly available

47

mature but are highly desirable 9.

Page 4 of 30

. In contrast, in-situ DIC sensor technologies are much less

48

Spectrophotometric methods are advantageous for simultaneous measurements of CO2

49

system parameters because all of the measurements can be made by absorbance detection of a

50

pH sensitive sulfonephthalein indicator in either the water sample or a standard solution

51

Moreover, spectrophotometric measurements are highly sensitive and stable, making them well-

52

suited for in-situ, underwater deployments. In addition, this method uses a low amount of sample

53

and reagent, requires low power consumption, and makes direct measurements of seawater. The

54

spectrophotometric method has become the benchmark for high-accuracy seawater pH

55

measurements

56

water and the pH is determined by measuring the ratio of the absorbance maxima of the

57

indicator’s acid and base wavelengths. In-situ applications of this method have achieved a

58

measurement uncertainty of 0.001-0.003 18-19, and are relatively immune to instrument drift often

59

encountered by potentiometric pH measurements.

15

. In this method

15, 23

22

.

, a small amount of pH indicator is added to the sample

60

In-situ DIC sensors for seawater applications have recently been developed based on CO2

61

equilibration between an acidified sample and a standard solution followed by either

62

spectrophotometric or conductometric detection

63

gas-sample CO2 equilibration followed by infrared detection, are also under development. The

64

established spectrophotometric DIC method

65

copolymer) capillary tubing as both an optical cell and a CO2 equilibrator since the material is

66

highly permeable to CO2 molecules and can act as a liquid-core waveguide (LCW) for optical

67

detection. The spectrophotometric detection occurs after full CO2 equilibration is established

68

between the acidified sample and the indicator solution. The time-limiting step of this method is

24-25

22, 24, 26

(Table S1). Other DIC sensors, based on

uses a piece of Teflon AF 2400 (DuPont

TM

ACS Paragon Plus Environment

4

Page 5 of 30

Environmental Science & Technology

69

the time that it takes for CO2 to equilibrate across the Teflon AF 2400 tubing, which is about 5

70

minutes. An improved spectrophotometric DIC method

71

faster response time and to allow for near continuous detection using a dynamic equilibration and

72

a countercurrent flow design (Figure 1). The response time of this method varies with indicator

73

flow rates, but can be as fast as 22s if partial equilibration27 is used. The improved method also

74

overcomes optical signal drifting that can occur when Teflon AF tubing is used as the optical

75

cell.

27

was recently developed to achieve a

76

This paper will describe the development and testing of a new, in-situ carbon sensor,

77

Channelized Optical System (CHANOS), which uses a modular design that is capable of making

78

simultaneous spectrophotometric measurements of seawater DIC and pH. The DIC channel uses

79

the improved spectrophotometric method 27. The sensor design was targeted for high-resolution,

80

time-series measurements at a fixed location. CHANOS is one of the first systems that is able to

81

fully resolve the carbonate system with a desirable pair of CO2 system parameters in a single

82

system. CHANOS has a built-in mechanism for in-situ calibration, which ensures high quality

83

measurements throughout a deployment cycle and reduces the need for laboratory calibration. In-

84

situ tests indicate that the system is able to make high-resolution, climatology-quality

85

measurements 15 to resolve seawater CO2 system dynamics.

86

METHODS AND MATERIALS

87

Principles.

88

(1) pH – The CHANOS pH channel uses a flow-through design in which seawater directly

89

and continuously mixes with an indicator solution

90

spectrophotometric pH method

15, 23

22

. It is based on the well-established

, where dissociation of the added sulfonephthalein indicator

ACS Paragon Plus Environment

5

Environmental Science & Technology

Page 6 of 30

91

KI H+ + I2 − ; KI is the dissociation constant of the (H2I) in seawater is dominated by HI− ←→

92

indicator acid species HI-. Combining Beer’s Law, seawater pH can then be expressed as:

93

pH = pKI + log

R − e1 , e2 − Re3

(1)

94

where R = λ2 A/ λ1 A , and λ1 and λ2 are the wavelengths for the absorbance maxima of HI- and I2-;

95

e1, e2, and e3 are indicator molar absorbance ratios at wavelengths λ1 and λ2: e1 =

∈HI , e2 = λ 1 ∈HI

λ2

∈I , e3 = λ 1 ∈HI λ2

∈I , λ 1 ∈HI

(2)

λ1

96

where λ1∈I and

97

λ2

98

work included thymol blue sodium salt 28 (λ1 = 435 nm and λ2 = 596 nm) and m-cresol purple

99

sodium salt 29 (λ1 = 434 nm and λ2 = 578 nm). A non-absorbing wavelength (700 nm) was used

λ2

∈I are the molar absorbances of I2- at wavelengths λ1 and λ2, and λ1∈HI and

∈HI refer to the molar absorbances of HI- at wavelengths λ1 and λ2. The indicators used in this

100

to correct baseline changes. Calibrations of pKI, e1, e2, and e3 of the two indicators for typical

101

seawater temperature and salinity have been established in laboratory experiments 28-29. It has

102

been demonstrated that in-situ spectrophotometric pH measurements require infrequent or no

103

calibration 19, 22.

104

(2) DIC – The CHANOS DIC channel utilizes continuous, countercurrent flow between the

105

indicator and acidified sample (Figure 1), instead of CO2 equilibration with static indicator used

106

in the previous method

107

maintaining a chemical concentration gradient

108

AF capillary tubing

109

acidified sample as the indicator flows through the Teflon AF tubing that is enclosed in the

27

24, 26

. This dramatically improves CO2 equilibration efficiency by 30-32

across the wall of the gas-permeable Teflon

. CO2 fugacity (fCO2) in the indicator equilibrates with fCO2 in the

ACS Paragon Plus Environment

6

Page 7 of 30

Environmental Science & Technology

110

sample flow cell. Partial or full CO2 equilibration can be achieved depending on the indicator

111

flow rate. After equilibration, DIC (as total CO2) of the acidified sample (denoted by subscript a)

112

is proportional to fCO2 of the internal indicator solution (denoted by subscript i) 27: log(p × fCO2)a = log( p ×

113

(3)

[ DIC] ) = log(fCO2)i ( K0 ) a

(K0)a is the Henry’s Law constant

33

for the acidified sample; p (value 0 – 1) is the

114

exchange efficiency or percentage of equilibration of CO2 when the indicator exits the Teflon

115

tubing. If the indicator reaches full CO2 equilibration, p has a value of 1 or 100%. Partial

116

equilibration (p