Interpenetrating Polymer Network Formation by Electron-Beam Curing

Interpenetrating Polymer Network. Formation by Electron-Beam Curing of Acrylated Epoxy Resin Blends. Mohamad Al-Sheikhly1 and William L. McLaughlin2...
0 downloads 0 Views 829KB Size
Chapter 14

Downloaded by UNIV MASSACHUSETTS AMHERST on October 14, 2012 | http://pubs.acs.org Publication Date: May 5, 1996 | doi: 10.1021/bk-1996-0620.ch014

Interpenetrating Polymer Network Formation by Electron-Beam Curing of Acrylated Epoxy Resin Blends 1

2

Mohamad Al-Sheikhly and William L. McLaughlin 1

Department of Materials and Nuclear Engineering, University of Maryland, College Park, MD 20742-2115 Ionizing Radiation Division, Physics Laboratory, National Institute of Standards and Technology, Technology Administration, U.S Department of Commerce, Gaithersburg, MD 20899

2

Continuous manufacturing processes of complicated structures of epoxy resin-graphite fiber composites require higher control of the level and dispersity of polymerization. This goal was achieved by using a two-step curing process involving different blends of unmodified epoxy resins with modified acrylated epoxy resins. The first step was designed to achieve partial curing of the blend by using high-energy electron beam (e-beam) irradiation, followed by full thermal curing. Higher glass transition temperature (T ) values were obtained by using modified fully unsaturated resins with unmodified epoxy resins, as compared to blends of modified monosaturated resins with unmodified epoxy resins. No partial curing was accomplished by e-beam irradiation of the unmodified epoxy resin alone. The present results demonstrate that the introduction of the fully-unsaturated resin blend increases the efficiency of the e-beam radiation curing through free-radical polymerization and then free-radical crosslinking, which leads to IPN formation. g

Over the past decade, high-energy electron radiation has been used to initiate the polymerization of acrylated epoxides. Unlike radiation-induced cationic polymerization of epoxides, polymerization of acrylated epoxides by ionizing radiation propagates by carbon-centered free radicals through the unsaturated end groups (1,2). In the present work, the two-part epoxy-based resin matrix is cured by a two-step process: (1) In the first step, an electron beam pre-cure supplies form stability; (2) a thermal cycle then completes the cure. The ultimate objective is to provide a controlled epoxy polymerization reaction through the blending of fully unsaturated epoxy with an unmodified epoxy. Such a blended resin contains a component which, when exposed to ionizing radiation, forms a three-dimensional 0097-6156/96y0620-0188$12.00/0 © 1996 American Chemical Society In Irradiation of Polymers; Clough, R., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1996.

Downloaded by UNIV MASSACHUSETTS AMHERST on October 14, 2012 | http://pubs.acs.org Publication Date: May 5, 1996 | doi: 10.1021/bk-1996-0620.ch014

14.

AL-SHEIKHLY & MCLAUGHLIN

IPN Formation by Electron-Beam Curing 189

structure within the unmodified epoxy resin. Thus, upon thermal curing of the unmodified epoxy resin component within the radiation cured matrix, an interpenetrating polymer network (IPN) is produced. This two-step approach, however, is not new. For example, it has been shown that radiation curing of a mixture of epoxy oligomer, acrylate, and styrene gives a higher gel content than chemically initiated curing of the same mixture and that post-irradiation heat treatment further increases the gel component to 92 to 98 percent (3-5). The required dose for achieving complete curing of this system was reported to be 100 to 120 kGy. It has also been demonstrated that, prior to irradiation, production of unsaturated ester by reaction of epoxy resins with acrylic acid enhances the radiation chemical yield of C-C reaction to 400 times that by irradiation of epoxide alone. In addition, crosslinking is enhanced by post-irradiation heating or by irradiation at elevated temperatures (6). In fact, in the presence of acrylates thermally initiated polymerization alone can occur at 160 °C (7). Another example of the post-irradiation thermal treatment of an epoxy oligomer-acrylate-polyamideplasticizer mixture has given better gel properties than with thermal curing of the same mixture (8). In addition, a combination of irradiation and heat treatment can be used to produce a resin network with high strength and thermal stability from a mixture of a bisphenol-A epoxy, polyamide and acrylic acid or acrylamide (9,10). It has been reported that high-energy electrons are also effective in curing carbon fiber prepregs (11). These prepregs (the type used in the aircraft industry for hand lay-up applications in polymer-carbon fiber composites) have been shown to contribute as integral components of high-strength, low-weight construction materials. Unfortunately, the radiation polymerization of most epoxy compounds proceeds by a cationic mechanism, a process that is inhibited by trace amounts of water. This obstacle, however, can be overcome by acrylating the terminal epoxy groups of epoxy oligomers which changes the system to a free-radical process, not inhibited by traces of water. Although not included in the present study, it should be noted that, by introducing certain onium salts to the system, gamma and e-beam-induced cationic polymerizations of epoxy resins can be achieved. Recent studies have shown that the initiation mechanism involves the production of radiation-induced radical cations of the epoxy monomer (or oligomer), followed by a deprotonation process to produce open-ring carboncentered radicals. The carbon-center is then oxidized by an onium salt through electron-transfer mechanisms to produce the monomer cation. The polymerization reaction then propagates through the addition of the cation to the monomer (12). Gamma rays have also been used to cure carbon fiber composites (13). Acrylate epoxy compounds were selected to achieve an aircraft-quality composite. The general formula that meets all the mechanical specifications imposed by a major U.S. aerospace company is: 20 percent dipentaerythritol monohydroxypentaacrylate; 30 percent polybutadiene diacrylate; and 50 percent epoxy diacrylate. A plain-weave carbon fabric was selected for the prepreg material. A solvent process using methylethylketone was used to impregnate the fabric with about 35 percent (by mass) resin. The prepared material was then irradiated at a dose-rate of 17 kGy/h to a total absorbed dose of 50 kGy. The ultimate objective of the work presented in this paper is to provide a controlled epoxy polymerization reaction by blending fully unsaturated epoxy with

In Irradiation of Polymers; Clough, R., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1996.

190

IRRADIATION OF POLYMERS

unmodified epoxy. Such a blended resin contains a component which reacts completely by radiation exposure to create a fully polymerized structure within the unreacted thermally-polymerizable unmodified epoxy resin. Thus an IPN can be formed by thermally crosslinking the unmodified epoxy-resin component within the radiation-cured unsaturated resin component. It is suggested here that by reaching these objectives, continuous radiation/thermal curing of epoxy-based resin matrices can be achieved on a production scale.

Downloaded by UNIV MASSACHUSETTS AMHERST on October 14, 2012 | http://pubs.acs.org Publication Date: May 5, 1996 | doi: 10.1021/bk-1996-0620.ch014

EXPERIMENTAL APPROACH In the present work, the experimental approach can be outlined as follows: 1. to devise a sequence of controlled epoxy polymerization using a blend of a fully unsaturated acrylated epoxy with an unmodified epoxy (without acrylated groups); 2. with irradiation, the unsaturated component should be capable of providing a polymerized structure within the thermally-polymerized unmodified epoxy resin; 3. subsequently, an IPN can be formed by crosslinking the unmodified epoxy within the radiation-cured unsaturated resin network. Thus, for controlling the polymerization process, the experimental approach is based on the following two-step curing approach:

Various Blends of Unsaturated Epoxy Resins

Unmodified Epoxy Resins

Radiation Curing

Thermal Crosslinking

In the first step, the unsaturated epoxy portion of the resin undergoes free-radical polymerization through doublebond formation to form a rubbery thermoplastic-like material

The second step of the curing reaction involves the crosslinking of the epoxy groups of the unmodified epoxy portion of the resin at 160 °C -two hours

Step 1

Step 2

Step 1: Radiation-induced polymerization: The unsaturated epoxy portion of the resin undergoes free-radical polymerization through the double bonds forming a rubbery thermoplastic material with high frictional properties. In order to enhance the radiation-induced free radical polymerization, partially and fully unsaturated resins are prepared by esterification of the epoxide resin with unsaturated acid.

In Irradiation of Polymers; Clough, R., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1996.

Downloaded by UNIV MASSACHUSETTS AMHERST on October 14, 2012 | http://pubs.acs.org Publication Date: May 5, 1996 | doi: 10.1021/bk-1996-0620.ch014

14.

AL-SHEIKHLY & MCLAUGHLIN

IPN Formation by Electron-Beam Curing 191

Step 2: Thermally-induced polymerization: Crosslinking of the unmodified epoxy portion of the resin is initiated by high-temperature treatment (160 °C for 2 h). A 2 to 9 MeV Varian V7715J Electron LINAC* was utilized to irradiate the neat epoxy resin and the 6-ply epoxy fiber prepared composite. An accelerating potential of 8 MeV was chosen to ensure full penetration of the electrons through the samples. The surface dose rate for the irradiation was 0.05 kGy per 3 pts pulse at a repetition rate of 20 pulses per second. FWT-60-00 radiochromic film dosimeters, traceable to the National Institute of Standards and Technology (NIST), were used to measure the total dose and dose per pulse (14). The combined estimated uncertainty of these measurements is documented as U = ku = ±3 percent, with the estimated standard deviation u = ±3 percent and the coverage factor k = 1) (15,16). In order to rniriirnize the effect of the temperature during irradiation, the total dose was fractionated into increments of 100 kGy or less, and a constant flow of cool air was aimed at the samples during and after irradiation. Several minutes cooling between fractionations was adequate to keep the irradiation temperature below 30 °C. Thefirststage of this study was the electron-beam curing of neat modified epoxies (acrylated epoxies), while the second stage was the electron-beam irradiation of the modified epoxy resin graphite composite. Graphite composite samples were produced by impregnating a plain-weave AS4 graphitefiberfabric using a typical wet layup method. Six-ply laminates were produced after preparing resin-impregnated single-ply elements. A Perkin Elmer DSC7 was used to measure the glass transition temperature (T ) values for the cured samples as an indication of degree of curing. For each T measurement, five specimens from the 6-ply composite were used. The thermograms were measured at a constant heat-up rate of 20 °C per minute. All measurements were carried out by employing ASTM standard practice D3418-82 for DSC analysis (17). Due to water contamination in the sample holder, the sample pans, and/or the laminate specimen, a few samples revealed slight transitions around 0 °C and 100 °C. c

c

g

g

RESULTS AND DISCUSSION The objective of thefirstpart of this two-step process for curing the epoxy-based resin matrices by electron-beam irradiation was to achieve a rubbery thermoplastic­ like (partially cured) composite. Thus, various blends of mono-unsaturated and fully-unsaturated resins with unmodified epoxy resin were irradiated by the electron beam at different dose levels in the range 100 to 300 kGy. At this stage no dose rate effect on yield was observed. Immediately after irradiation, T values were measured. As expected, no significant polymerization was found for the irradiated unmodified epoxy resin, even at comparatively high doses (—300 kGy). g

*The mention of commercial products throughout this paper does not imply recommendation or endorsement by the National Institute of Standards and Technology, nor does it imply that the products identified are necessarily the best available for the purpose.

In Irradiation of Polymers; Clough, R., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1996.

192

IRRADIATION OF POLYMERS

This can be explained by the fact that the radiolytically produced cations transfer a proton to the H 0 molecules converting the protonated epoxy species to stable epoxy oligomer. On the other hand, the blended samples show some degree of polymerization. The second curing step was the post-irradiation thermal treatment of the samples. T measurements were also carried out after the thermal treatment. The results of the electron irradiation of neat epoxy and different blend ratios of neat mono-unsaturated epoxy (modified) resins mixed with unmodified epoxy resins and their effects on the T values at different absorbed levels and after thermal treatment are summarized in Table I. The combined uncertainty of the T measurements is estimated to be U = k« = ±8 percent, with a standard deviation of k = ±8 percent and the coverage factor k = 1 (76). 2

g

Downloaded by UNIV MASSACHUSETTS AMHERST on October 14, 2012 | http://pubs.acs.org Publication Date: May 5, 1996 | doi: 10.1021/bk-1996-0620.ch014

g

g

c

c

Table I. T For Neat and Modified Epoxy Resins g

Blend Formulation

un-modified epoxy resin un-modified epoxy resin (100 parts)

+ mono-unsaturated epoxy (50 Parts) un-modified epoxy resin (100 parts)

+ mono-unsaturated epoxy resin (200 parts)

Absorbed Dose (kGy) 0 92 183 300

T. after Irradiation (°C) N/M* N/M N/M N/M

T after Post Cure (°C) 152.2 155.0 153.7 156.5 g

0 92 183 300

N/M -8.9 -7.5 -9.5

113.4 129.4 128.9 134.6

0 92 183 300

N/M -5.6 -4.3 -4.0

78.4 130.8 135.2 132.7

*not measurable, the blend still in a liquid phase after irradiation The results in Table I show that increasing the percentage of the monounsaturated resin component leads to an increase in the glass transition temperature due to free-radical polymerization (see scheme 1). These data also show that the unmodified epoxy resin reaches full curing by thermal treatment despite the fact that no appreciable polymerization was achieved by irradiation alone. The same experimental two-step (irradiation + thermal) approach was used for curing different blends of modified epoxy resins in matrix graphite-fiber

In Irradiation of Polymers; Clough, R., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1996.

IPN Formation by Electron-Beam Curing 193

Downloaded by UNIV MASSACHUSETTS AMHERST on October 14, 2012 | http://pubs.acs.org Publication Date: May 5, 1996 | doi: 10.1021/bk-1996-0620.ch014

AL-SHEIKHLY & McLAUGHLIN

BLEND SOLUTION

Irradiation ^

CH 3

CH 3

„ |, H

C

H

C

H

cr

S*

R

v

H

C

H

C

H

cr

l> H CH,

3

C H j

S

C

CIl, + c

CH,

H

C

R

R

H

C

\

H

H

N

l>

H CH

R

C

R H -

J i

H

C

-C

> S H

C

"1

? \

C H j

H

C\

CHJ R

v

Scheme 1.

In Irradiation of Polymers; Clough, R., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1996.

194

IRRADIATION OF POLYMERS

composite samples. Electron beam-induced partial curing of two-resin compositions was carried out: (1) a blend of unmodified epoxy resin (100 parts) with a mono-unsaturated epoxy resin (50 parts); and (2) a blend of unmodified epoxy resin (100 parts) with fully unsaturated epoxy (23) parts. T values resulting from two-step curing of different blends of modified epoxy resins in matrix graphite-fiber composites are summarized in Table II. Higher T values were found for fiilly-unsaturated blend samples compared to those of the monounsaturated samples when treated by electron-beam irradiation. However, at very high dose (300 kGy), the results indicate that degradation starts predominating (T lowered by -5 percent). g

g

Downloaded by UNIV MASSACHUSETTS AMHERST on October 14, 2012 | http://pubs.acs.org Publication Date: May 5, 1996 | doi: 10.1021/bk-1996-0620.ch014

g

Table II. T For Modified Epoxy Graphite Composites g

Blend Formulation un-modified epoxy resin (100 parts) + mono-unsaturated epoxy (50 parts) un-modified epoxy resin (100 parts) + fully-unsaturated (the diester) (23 parts)

Absorbed Dose (kGy)

T after Irradiation (°Q

T after Post Cure (°Q

100 200 300

7.4 5.6 7.6

116.9 125.9 127.2

100 200 300

6.7 9.9 11.0

137.4 136.2 129.9

g

g

SUMMARY AND CONCLUSION The present work shows that epoxy resin polymerization solely by electron irradiation initiation cannot be achieved. This is likely due to the presence of traces of water. Such proton acceptors have been shown to inhibit cationic polymerization (18). On the other hand, electron irradiation-induced partial curing occurs in the presence of unsaturation, since polymerization proceeds through a free-radical mechanism (scheme 1). While polymerization through cation propagation is inhibited by the presence of proton donors, free radical-induced polymerization can be impeded by the presence of dissolved oxygen and at higher dose rates. Oxygen reacts very fast with carbon centered radicals to produce the corresponding peroxy radicals. In this way the dissolved oxygen will react with modified epoxide [mono- and/or fully unsaturated epoxy] free radicals, E", thus

In Irradiation of Polymers; Clough, R., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1996.

14.

AL-SHEIKHLY & McLAUGHLIN

IPN Formation by Electron-Beam Curing 195

impeding the additional reaction of E' with another monomer molecule (propagation reaction). Hence the reaction E" + 0

2

-* EO2

(1)

interferes with E +E

EE" (propagation)

(2)

Downloaded by UNIV MASSACHUSETTS AMHERST on October 14, 2012 | http://pubs.acs.org Publication Date: May 5, 1996 | doi: 10.1021/bk-1996-0620.ch014

Additionally, the radical-radical reaction, which can be enhanced at high dose rates, also competes with the propagation reaction E + E" -> E - E

(dimerization)

3

()

Moreover, dissolved oxygen reacts extremely fast with the electron in competition with the monomer. As a result, the efficiency of radiation-induced polymerization will be decreased. Despite the negative effects of oxygen, the results demonstrate that by implementing a two-step curing method (irradiation and post-irradiation thermal curing) of compositions blended with mono-unsaturated epoxy and fully unsaturated epoxy, the sequence of controlled epoxy polymerization can be optimized, thus providing manufacturing advantages in the production of stable cured resins. Equally important is the possible formation of IPN's by the introduction of the fully-unsaturated resin blend, which increases the efficiency of electron-beam curing by free-radical polymerization and subsequentfree-radicalcrosslinking, giving controlled T values. Since the main objective of this work has been to introduce a novel method of continuous mass production of composite curing for complex geometrical structures, by using electron beams for partial curing followed by complete thermal curing, no attempts were made here to irradiate under anaerobic conditions to minimize the oxygen inhibition effects. g

LITERATURE CITED 1. 2.

3. 4. 5. 6. 7. 8.

Crivello, J. V.; Fan, M.; Bi, D. J. Appl. Polymer Sci. 1992, 44, 9. Gotoda, M.; Miyashita, Y.; Takeyama, K. In Fundamental Studies in Osaka Laboratory for Radiation Chemistry. 1975, Annual Report: April 1 1973-March 31, 1974, JAERI-5030, 125-135. Kuznetsova, V. M.; Meleshevich, A. P.; Vishev, Yu. V.; Gorodnichenko, A. I. Plast. Massy 1978a, 2, 46. Kuznetsova, V. M.; Meleshevich, A. P.; Vishev, Yu. V.; Zhikharev, V. S.; Derevyanko, A. G. Plast. Massy 1978b, 2, 44. Kuznetsova, V. M.; Meleshevich, A. P.; Fedina, L. P.; Vishev, Yu. V.; Gerasimenko, E.V. Plast. Massy 1978c, 2, 49. Persinen, A. A. Proc. 5th Tihany Symp. Radiat. Chem. 1982, 2, 1005. Takács, E. Radiation Chemistry Group, Institute of Isotopes of the Hungarian Academy of Sciences, Budapest, private communication. Vishev, Yu. V.; Furman, Ye. G.; Melesgevich, A. P.; Kuznetsova, V. M.; Valatina, O. A. Vysokomol. Soyed. 1983, A25, 970.

In Irradiation of Polymers; Clough, R., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1996.

196 9. 10. 11. 12.

Downloaded by UNIV MASSACHUSETTS AMHERST on October 14, 2012 | http://pubs.acs.org Publication Date: May 5, 1996 | doi: 10.1021/bk-1996-0620.ch014

13. 14.

15.

16. 17. 18.

IRRADIATION OF POLYMERS

Barunin, A. A.; Plachenov, B. T.; Krasovskaya, I. A.; Vesnebolotskii, K. I.; Masloboev, D. S. Mekh. Kompoz. Mater. (Zinatne) 1983, 5, 935. Ivanov, G. M.; Neschastnova, L. M.; Vinogradova, V. V.; Shiryaeva, G. V.; Prishchepa, N. D.; Plast. Massy 1985, 3, 24. Dikson, L. B.; Singh, A. Radiat. Phys. Chem. 1988, 31, 587. Crivello, J. V; Mingxin, F.; Daoshen, B.; J. Appl. Polymer Sci. 1992, 44, 9. Saunders, C. B.; Dickson, L. W.; Singh, A. A.; Polymer Composites 1988, 9, No. 6, 389. McLaughlin, W. L.; Humphreys, J. C.; Wei-Zhen, BA; Khan, H. M.; AlSheikhly, M.; Chappas, W. J. High Dose Dosimetry for Radiation Processing, Proceedings of International Symposium, IAEA STI/PUB/846, held in Vienna, 5-9 November 1990. International Atomic Energy Agency: Vienna, 1991, pp 305-316. McLaughlin, W. L.; Boyd, A. W.; Chadwick, K. H.; McDonald, J. C.; Miller, A. Dosimetry for Radiation Processing (Taylor and Francis, London) 1989 Taylor, B. N.; Kuyatt, C. E. NIST Technical Note 1297, National Institute of Standards and Technology, Gaithersburg, MD. ASTM Standard D 3418-82, ASTM Standard-Composite Materials, Second Edition, American Society for Testing and Materials, Philadelphia PA, 1990. Al-Sheikhly, M. and McLaughlin, W. L. Mechanism of Radiation-Induced Curing of Epoxy-Fiber Composites. In Radiat. Phys. Chem. Editor W. Chappas (1996) in press.

RECEIVED

November 22, 1995

In Irradiation of Polymers; Clough, R., et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 1996.