Investigation of U(VI) Adsorption in Quartz–Chlorite Mineral Mixtures

Jun 14, 2014 - The luminescence intensity decreased in a nonlinear manner as the adsorbed U(VI) concentration increased with increasing chlorite mass ...
0 downloads 0 Views 595KB Size
Subscriber access provided by UNIV OF DAYTON

Article

Investigation of U(VI) Adsorption in Quartz-Chlorite Mineral Mixtures Zheming Wang, John M Zachara, Jianying Shang, Choong Jeon, Juan Liu, and Chongxuan Liu Environ. Sci. Technol., Just Accepted Manuscript • Publication Date (Web): 14 Jun 2014 Downloaded from http://pubs.acs.org on June 19, 2014

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 33

Environmental Science & Technology

1 2 3 4 5

Investigation of U(VI) Adsorption in Quartz-Chlorite Mineral Mixtures Zheming Wang,* John M. Zachara, Jianying Shang, Choong Jeon†, Juan Liu and Chongxuan Liu

6

Pacific Northwest National Laboratory, Richland, WA 99352

7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37

*

Corresponding author: Pacific Northwest National Laboratory, P.O. Box 999, MS K8-96, Richland, WA 99354; Phone: (509) 371-6349; Fax: (509) 371-6354; E-mail: [email protected] † Present Address: Department of Environmental & Applied Chemical Engineering, Gangneung-Wonju National University, Gangwon-do, Republic of Korea.

1 ACS Paragon Plus Environment

Environmental Science & Technology

38

ABSTRACT

39 40

A batch and cryogenic laser-induced time-resolved luminescence spectroscopy

41

investigation of U(VI) adsorbed on quartz-chlorite mixtures with variable mass ratios

42

have been performed under field-relevant uranium concentrations (5x10-7 M and 5x10-6

43

M) in pH 8.1 synthetic groundwater. The U(VI) adsorption Kd values steadily increased

44

as the mass fraction of chlorite increased, indicating preferential sorption to chlorite. For

45

all mineral mixtures, U(VI) adsorption Kd values were lower than that calculated from the

46

assumption of component additivity possibly caused by surface modifications stemming

47

from chlorite dissolution; The largest deviation occurred when the mass fractions of the

48

two minerals were equal. U(VI) adsorbed on quartz and chlorite displayed characteristic

49

individual luminescence spectra that were not affected by mineral mixing. The spectra of

50

U(VI) adsorbed within the mixtures could be simulated by one surface U(VI) species on

51

quartz and two on chlorite. The luminescence intensity decreased in a nonlinear manner

52

as the adsorbed U(VI) concentration increased with increasing chlorite mass fraction –

53

likely due to ill-defined luminescence quenching by both structural Fe/Cr in chlorite, and

54

trace amounts of solubilized and re-precipitated Fe/Cr in the aqueous phase. However,

55

the fractional spectral intensities of U(VI) adsorbed on quartz and chlorite followed the

56

same trend of fractional adsorbed U(VI) concentration in each mineral phase with

57

approximate linear correlations, offering a method to estimate of U(VI) concentration

58

distribution between the mineral components with luminescence spectroscopy.

2 ACS Paragon Plus Environment

Page 2 of 33

Page 3 of 33

59

Environmental Science & Technology

INTRODUCTION

60

The adsorption of uranium to soil minerals and subsurface sediments has been

61

extensively investigated to resolve issues of environmental contamination and to support

62

site selection of nuclear waste repositories.1-4 Under most environmental conditions,

63

uranium exists as the hexavalent uranyl ion, UO22+. Uranyl ion adsorbs to a broad range

64

of mineral phases including quartz,5, 6 feldspar,7 calcium carbonates,8, 9 iron oxides,10, 11

65

and phyllosilicates.12,

66

strongly on solution pH and counter anions.

67

precipitate in the form of uranyl phosphate, carbonates, and oxyhydroxides mineral

68

phases.14-16

13

Adsorption affinities to these phases are variable, depending At higher concentrations, uranyl may

69

Metal ions may exhibit distributed adsorption in mineral assemblages and natural

70

sediments. For example, Stubbs et al. identified six mineral hosts for sorbed uranium in

71

Hanford vadose zone sediment based on electron microprobe and TEM analysis.17 The

72

overall adsorptivity of a composite mineral material is influenced by the adsorption

73

characteristics of the contributing mineral phases and their mass fractions, and by

74

interactions between the adsorbing mineral phases.18

75

The description of metal ion adsorption on mineral mixtures and sediments relies

76

heavily on surface complexation modeling to account for aqueous chemical and surface

77

effects. Two common surface complexation modeling approaches are the generalized

78

composite model (GCM) and the component additivity model (CAM).19-22 In the former,

79

generic surface sites are assumed for the entire mineral assemblage. Site density and

80

possible surface complexes with fitted stability constants are applied under different

81

adsorption conditions to determine the likely adsorption mechanism(s) based on the

3 ACS Paragon Plus Environment

Environmental Science & Technology

82

goodness of fit. In the latter, adsorption is described as the summation of that occurring

83

on individual mineral phases,19 as computed from individual surface complexation

84

constants and the abundance of the mineral components in the assemblage.

85

Regardless of the surface complexation modeling approach, understanding the

86

adsorption process in natural materials is advanced by direct identification of surface

87

complex types and their concentrations. These speciation measurements are challenging

88

due to sensitivity issues and the multi-component nature of the surface complexation

89

process. In a previous study, we applied time-resolved U(VI) luminescence spectroscopy

90

and chemometric methods to determine the chemical forms of adsorbed U(VI) in a

91

contaminated subsurface sediment.23 As U(VI) adsorbed to constituent mineral phases

92

displayed characteristic luminescence spectra, we were able to determine that sediment

93

adsorbed U(VI) existed as surface complexes on quartz and phyllosilicates. However, it

94

was unclear if sorbent interactions influenced the luminescence spectral behavior, and if

95

the spectral intensity could be used to estimate the concentrations of specific surface

96

complex type. Here, we investigated U(VI) adsorption on mixtures of quartz and chlorite

97

to simulate the reactive fraction of a subsurface sediment. Sorbent mass ratios were

98

varied and the adsorption complex was examined by cryogenic luminescence

99

spectroscopy to determine how luminescence spectral behavior evolved with changing

100

mineral mass ratios in the mixtures. We assess whether it is possible to estimate the

101

concentration of U(VI) on the individual phases in the mixtures based on the collective

102

luminescence response.

103 104 105

EXPERIMENTAL

4 ACS Paragon Plus Environment

Page 4 of 33

Page 5 of 33

106

Environmental Science & Technology

Materials

Quartz (Min-U-Sil 30, U.S. Silica Company, Mill Creek,

107

Oklahoma) was pretreated to remove organic contaminants and reactive fines following

108

the procedures of Kohler et al24 and rinsed with DI water until the supernatant

109

conductivity was 18 MΩ cm or lower. The material was then oven-dried at 40 °C for 3−4

110

days. Specific surface area was determined by the N2 BET method (Quantachrome

111

Autosorb 6-B gas adsorption system) to be 1.63 m2/g.

112

[(Mg2.95Al0.05)(Si2.99Al1.01)O10(OH)2.(Mg1.97Al0.66 Cr0.25Fe3+0.06Fe2+0.06) (OH)6;25] was

113

hand ground to yield 20-53 µm fraction with a BET surface area of 2.6 m2/g. The

114

properties of smaller size fractions of the same mineral specimen (2 to 5 µm and 5 – 20

115

µm) have been previously reported.23 Calcite-saturated synthetic groundwater (SGW2;

116

pH 8.1) was prepared according to Bond et al.26 A stock solution of uranium nitrate (1.06

117

x 10-3 M, pH 1) was prepared by dissolving a weighed amount of uranyl nitrate (Fluka) in

118

0.1 M nitric acid. All other chemicals were reagent grade.

California chlinochlore

119

U(VI) Adsorption Two identical series of eleven quartz-chlorite mixtures were

120

prepared by mixing weighed amounts of the solids in 15 ml polypropylene centrifuge

121

tubes to quartz:chlorite mass ratios of 10:0, 9:1, 8:2, 7:3, 6:4, 5:5, 4:6, 3:7, 2:8, 1:9 and

122

0:10. The total mineral weight was 0.2 g. The sorbents were twice equilibrated with

123

SGW2 for 24 h and separated from the supernatants by centrifugation. The resulting

124

solids were then re-suspended in 10 ml of SGW2 and spiked with the U(VI) stock

125

solution to yield 5x10-6 M U(VI) in one series and 5x10-7 M U(VI) in the other. The

126

suspension pH was maintained at pH 8.1 with dilute NaOH. The U(VI)-bearing mineral

127

suspensions were placed on an orbital shaker and slowly agitated for 48 h to allow U(VI)

128

adsorption equilibrium.

After 48 h, the solid and solution were separated by

5 ACS Paragon Plus Environment

Environmental Science & Technology

Page 6 of 33

129

centrifugation. Both the solid paste and the supernatant were sampled into 2 mm x 4 mm

130

x 25 mm (ID) quartz cuvettes for luminescence analysis, while the remainder of the

131

supernatants was acidified for U(VI) (KPA), Mg, Al, Si and Fe analysis (ICP/MS).

132

Aqueous U(VI) speciation calculation The speciation of U(VI) in SGW2 at pH

133

8.1 under ambient conditions was calculated using the MINTEQA227 software with the

134

most current, critically reviewed thermodynamic stability constants for the U(VI)

135

complexes.28

136

Cryogenic Laser Luminescence Spectroscopy

The instrumentation and

137

experimental procedures for luminescence spectroscopic measurements at LHeT were

138

described previously.15, 29 The quartz sample cuvettes were attached to the cold finger of

139

a CRYO Industries RC152 cryostat with liquid helium vaporizing beneath the sample to

140

reach a sample temperature of 8 ± 2 ̊K. The sample was excited with a Spectra-Physics

141

Nd:YAG laser pumped Lasertechnik-GWU MOPO laser at 415 nm and the emitted light

142

was collected at 85˚ to the excitation beam and detected with a thermoelectrically cooled

143

Princeton Instruments PIMAX intensified CCD camera after spectral dispersion through

144

an Acton SpectroPro 300i double monochromator spectrograph.

145

analyzed using a commercial software, IGOR®, from Wavematrix, Inc. All spectra were

146

corrected for the mass ratio-weighted background emission observed for quartz and

147

chlorite prepared under the same conditions as those of the U(VI)-bearing samples except

148

that no U(VI) was added.

149 150

RESULTS AND DISCUSSION

6 ACS Paragon Plus Environment

The spectra were

Page 7 of 33

Environmental Science & Technology

151

Adsorption of U(VI) on quartz-chlorite mixtures The magnitude of U(VI)

152

adsorption on the quartz-chlorite mixtures varied with the mineral mass ratio and U(VI)

153

concentration (Table 1 and Figure 1). The highest adsorption was seen on pure chlorite

154

and the lowest on pure quartz. At a U(VI) concentration of 5×10-6 M, U(VI) adsorption

155

was 36.2% on quartz and 84.9% on chlorite, corresponding to adsorption Kd values of

156

28.3 ml/g and 281 ml/g, respectively. Lowering the U(VI) concentration to 5×10-7 M

157

increased U(VI) adsorption to 46.7% on quartz and 92.9% on chlorite, corresponding to

158

Kd values of 43.7 and 870 ml/g, respectively. These measured Kd values were consistent

159

with ones measured previously,23 when differences in surface areas are taken into

160

account.

161

As a result of the disparate U(VI) adsorption on the two phases, the total adsorbed

162

U(VI) concentration, CU,Ads, increased with the mass fraction of chlorite (Table 1 and SI

163

Figure 1). The concentration of adsorbed U(VI) contributed by quartz and chlorite in the

164

solid mixtures at each initial U(VI) concentration were calculated through the following

165

relationship, f Q × K d ,Q f Q × K d ,Q + f CC × K d , CC

166

CU,Q = CU,Ads ×

167

CU,CC = CU,Ads - CU,Q

(1)

(2)

168

Where CU,Q and CU,CC were adsorbed U(VI) concentrations contributed by quartz and

169

chlorite in the mineral mixture. Kd,Q and Kd,CC were the U(VI) adsorption Kd values on

170

pure quartz and chlorite at the corresponding initial U(VI) concentration, and fQ and fCC

171

were the respective mass fractions. The fractional concentration contribution to the

172

adsorbed U(VI) by quartz (FU,Q) and chlorite (FU,CC) in the mixtures were defined as: 7 ACS Paragon Plus Environment

Environmental Science & Technology

173

FU,Q = CU,Q/CU,Ads and FU,CC = CU,CC/CU,Ads

Page 8 of 33

(3)

174

Reflecting the lower affinity of quartz as compared to chlorite, the calculated U(VI)

175

concentration contributions from quartz were consistently lower in all quartz-chlorite

176

mixtures (SI Figure 2). For all mineral mixtures in which fCC > 0.5, the fractional

177

concentration contribution of quartz to adsorbed U(VI) in the mineral mixtures was ~ 5%

178

or less (Figure 2).

179

With the component additivity model, the distribution coefficient for adsorbed

180

U(VI) in the quartz-chlorite mixtures equals the mass-weighted sum of the adsorption Kd

181

values on the individual sorbents,18, 30, 31

182

Kd, mixture = fQ Kd, Q + fCC Kd, CC

(4)

183

Accordingly, the calculated Kd values displayed straight lines as a function of chlorite

184

mass fraction at both U(VI) concentrations (dashed lines in Figure 1). The calculated Kd

185

values were all above the measured ones for the mineral mixtures, and the largest

186

differences were observed when both minerals were at equal mass. Such deviations

187

suggest that either there is interaction between the quartz and chlorite, or that surface

188

modifications occurred as a result of mineral mixing and co-equilibration. Apparently,

189

the component additivity approach is not valid for quantitatively modeling U(VI)

190

adsorption in such mixtures without properly taking into account the causes for the

191

deviation.

192

Previous studies on the applicability of adsorption additivity for metal ion

193

adsorption in binary mineral mixtures18, 32, 33 revealed dependence on the specific metal

194

ion and sorbent identity. The adsorption of both Cs+ and Sr2+ followed the additivity rule

195

on bentonite-sand and silica-montmorillonite mixtures.18 However, significant negative 8 ACS Paragon Plus Environment

Page 9 of 33

Environmental Science & Technology

196

deviations from adsorption additivity were observed for Sr2+ adsorption on alumina-illite

197

mixtures, while large positive deviations were observed for Sr2+ adsorption on alumina-

198

montmorillonite mixtures.18 The dissolution of alumina and the formation of unidentified

199

Sr-bearing precipitates were speculated to cause the noted effect.

200

Anderson and Benjamin systematically investigated the adsorption of Ag+, Cd2+,

201

Zn2+ and several inorganic anions on Fe(OH)3, Al(OH)3, and Fe(OH)3-Al(OH)3 mixtures

202

and co-precipitates under various chemical conditions.32,

203

caused small enhancements in Zn2+ adsorption by Fe(OH)3 but inhibited the adsorption of

204

Ag+ and Cd2+. Constant-capacitance surface complexation modeling suggested that a

205

majority of the Fe(OH)3 surface sites were covered and replaced by Al(OH)3 upon

206

mixing, leading to reduced metal ion adsorption. Surface and bulk analyses clearly

207

indicated that particle interactions in the mixtures, including dissolution and precipitation,

208

resulting in changes in particle size distribution, surface charge, and surface site

209

distribution.

33

The presence of Al(OH)3

210

SEM images of the post-reaction quartz-chlorite mixture (SI Figure 3) revealed

211

that the individual phases generally remained separate except that fine-grained quartz

212

associated with larger chlorite platelets.

213

aggregation of the sorbents was an unlikely cause of the observed lower Kd values, which

214

in some samples was as much as 50% as compared to the pure phases (Figure 1). We

215

hypothesize that the decrease of Kd values for the quartz-chlorite mixtures was due to

216

trace amounts of the dissolved solids, particularly the brucite layer of chlorite, releasing

217

Mg2+, Al3+, Cr3+, Fe3+ and Fe2+.

218

concentration in the presence of chlorite was between 17 µM to 48 µM higher than that in

Thus, surface area loss due to physical

As indicated by the results of ICP analysis, Mg

9 ACS Paragon Plus Environment

Environmental Science & Technology

219

SGW2 and increases along with the mass fraction of chlorite (SI Figure 4), equivalent to

220

between 0.01% to 0.04% chlorite dissolution.

221

stoichiometric concentrations of other metal ions are also released into the solution.

222

Some of the leached metal ions may occupy surface sites that would otherwise be

223

available for uranyl adsorption, especially on quartz which is mostly negatively charged

224

at the present pH. As will be shown in the next section, a major surface U(VI) complex

225

on chlorite involved the negatively charged uranyl-tricarbonate anion complex,

226

UO2(CO3)34-. Therefore, the loss of highly-charged cation sites on chlorite would also

227

reduce U(VI) sorption on chlorite. In addition, the attachment of negatively charged fine

228

quartz particle might also adversely impact the adsorption U(VI) on some of the

229

positively charged surface sites on chlorite.

230

If the dissolution is congruent,

Luminescence spectroscopy of adsorbed U(VI) The luminescence spectra of

231

U(VI) adsorbed on the quartz-chlorite mixtures displayed characteristic features (Figure

232

3). The vibronic band maxima were located at 499.7 nm, 520.4 nm and 541.3 nm for

233

U(VI) adsorbed on quartz at an initial U(VI) concentration of 5x10-6 M, while those for

234

U(VI) on chlorite were at 480.3 nm, 500.8 nm, 521.4 nm and 543.2 nm (Figure 3A and SI

235

Table 1). These results were in good agreement with previously reported values.23 The

236

uranyl ion formed inner-sphere surface complexes with deprotonated silanol sites on

237

quartz, while the U(VI) spectra on chlorite resembled those of uranyl-

238

tricarbonate/dicarbonate or calcium-uranyl-tricarbonate complexes.29, 34, 35 The spectral

239

features of U(VI) adsorbed on quartz decreased and eventually disappeared as the mass

240

fraction of chlorite (fCC) increased. The spectral pattern for chlorite, defined here as UCa,

241

became dominant over fCC = 0.5.

10 ACS Paragon Plus Environment

Page 10 of 33

Page 11 of 33

Environmental Science & Technology

242

The spectrum of U(VI) adsorbed on quartz was unchanged at 5x10-7 M U(VI) as

243

compared with that at 5x10-7 M U(VI) (Figure 3B). However, the spectra of U(VI)

244

adsorbed on chlorite developed more than one spectral pattern at this concentration. The

245

spectrum was identical to UCa when fCC < 0.5 while a broad, poorly resolved spectra

246

with an emission maximum of 521.7 nm (SI Table 1), defined here as pattern UCb,

247

became dominantt at fCC > 0.5 (Figure 3B lower traces), indicating the presence of

248

another U(VI) surface complex on chlorite.

249

U(VI) luminescence spectra were also recorded for the supernatants and for

250

SGW2 that was spiked with U(VI) nitrate (data not shown). Consistent with previous

251

measurements, U(VI) in the supernatants showed luminescence spectra that closely

252

resembled those of Ca2UO2(CO3)3(aq) and CaUO2(CO3)32- complexes as expected from

253

aqueous speciation calculation. The same type of spectra were displayed on the time-

254

resolved spectra of both of the wet paste samples of U(VI) adsorbed on quartz and

255

chlorite at 5x10-6 M U(VI) at long delay times, consistent with the presumption that the

256

wet paste samples entrained a small fraction of the supernatant. Such spectra were absent

257

in samples with large fCC values at 5x10-7 M U(VI) as a results of nearly complete U(VI)

258

adsorption.

259

Time-resolved luminescence spectra at delay times up to 4 ms showed that while

260

there was a single dominant species of U(VI) adsorbed on quartz (data not shown), both

261

U(VI) surface species on chlorite represented by the UCa and UCb spectral patterns were

262

present at 5x10-6 M U(VI), as expected, and UCb became more pronounced at longer

263

delay times (SI Figure 5). For all the samples with U(VI) adsorbed on quartz-chlorite

264

mixtures, the time-resolved spectra reflected the variation of the relative intensities of the

11 ACS Paragon Plus Environment

Environmental Science & Technology

265

three surface U(VI) species as governed by their luminescence lifetimes. For example,

266

for U(VI) adsorbed on quartz-chlorite mixture with fCC = 0.4 at 5x10-6 M U(VI), the

267

spectra were primarily composed of those of U(VI) adsorbed on quartz and on chlorite

268

with a spectral pattern UCa at shorter delay times (Figure 4A). As the delay time

269

increased, the relative intensity of UCa decreased gradually as indicated by the slight

270

drop of intensity in the 480.3 nm band where the spectra of U(VI) adsorbed on quartz

271

displayed only weak emission, pointing to increased character of U(VI) adsorbed on

272

quartz. At the same time, the relative intensity in the region from ~ 510 nm to 550 nm

273

was noticeably elevated, a clear indication of the growing contribution of the species

274

UCb.

275

spectral pattern UCa had a shorter luminescence lifetime than the U(VI) surface species

276

on quartz and the U(VI) species with a spectral pattern UCb had the longest luminescence

277

lifetime.

Such spectral changes implied that the surface U(VI) species corresponding to

278

As shown for the sample with fCC = 0.3, the time-resolved emission spectra at

279

5x10-7 M U(VI), again, indicated that at shorter delay times, the spectra represented both

280

U(VI) adsorbed on quartz and chlorite (UCa), and the latter decreased as delay time

281

increased to 0.7 ms based on the gradual drop of the intensity of the 480.3 nm band

282

(Figure 4B). As delay time further increased to 2.8 ms and 4.0 ms the spectral character

283

of U(VI) adsorbed on quartz also disappeared and the spectra became similar to those

284

observed at large fCC values (≥ 0.6) with dominant spectral pattern UCb at the same

285

U(VI) concentration, confirming the presence of two U(VI) surface complexes on

286

chlorite: one with spectral pattern UCa at lower fCC values and shorter delay times, and

287

the other with spectral pattern UCb that was present primarily at higher fCC values and

12 ACS Paragon Plus Environment

Page 12 of 33

Page 13 of 33

Environmental Science & Technology

288

longer delay times at low U(VI) concentration (i.e. 5x10-7 M)(Figures 3B, 4B). Thus the

289

second surface U(VI) species on chlorite (UCb) likely formed on a subset of surface sites

290

with the highest U(VI) affinities. The site density for surface U(VI) complex with

291

spectral pattern UCa is much higher and thus this complex dominated at higher U(VI)

292

concentrations. The UCb spectrum was red-shifted by over 20 nm as compared to UCa,

293

which reflected the formation of strong, inner-sphere surface complex, consistent with

294

U(VI) adsorption at sites of higher U(VI) affinity.

295

Further spectral analyses verified that the luminescence spectra of adsorbed U(VI)

296

on all of the quartz-chlorite mixtures could be simulated by a linear combination of the

297

three species described above: one U(VI) surface complex on quartz and two on chlorite

298

with spectral profiles of UCa and UCb (Figure 5 as an example).

299

characteristics of U(VI) surface complexes on the individual phases were not affected by

300

mixing of the mineral components.

Therefore, the

301

Luminescence decay analysis indicated that the decay curves of U(VI) adsorbed

302

on chlorite could be fit by two exponential functions, resulting in luminescence lifetimes

303

of 155 ± 52 µs and 1328 ± 396 µs, respectively, consistent with the assignment to the

304

U(VI) species with spectral patterns of UCa and UCb. Unexpectedly, fit of the decay

305

curves of U(VI) adsorbed on quartz also required two exponential functions with

306

luminescence lifetime of 796 ± 142 µs and 233 ± 135 µs, respectively (SI Table 1). This

307

could be due to many reasons, such as two U(VI) surface complexes on quartz with

308

similar profiles, same surface species with different hydration waters or surface cite

309

inhomogeneity 2, 36, 37. The trend of the measured luminescence lifetimes were consistent

310

with that expected from the variations of the time-resolved spectra (Figure 4). However,

13 ACS Paragon Plus Environment

Environmental Science & Technology

Page 14 of 33

311

it should be cautioned that large deviations were observed in the measured luminescence

312

lifetimes data, possibly due to sample heterogeneity, and luminescence decay fitting with

313

multiple exponential functions are prone to errors.

314

Variation of U(VI) spectral intensities with mineral compositions Countering

315

the trend of the increasing Kd values (Table 1) and adsorbed U(VI) concentration with

316

increasing fCC values (SI Figure 1), the overall spectral intensity decreased with

317

increasing fCC (Figure 6). The sharpest intensity reduction occurred at fCC ≤ 0.2. The

318

spectral area for U(VI) adsorbed on quartz (fCC = 0) was 461 times larger than U(VI)

319

adsorbed on chlorite (fCC = 1) at 5x10-7 M U(VI), and 775 times larger at 5x10-6 M

320

U(VI). Given that the adsorbed U(VI) concentration on chlorite was more than twice that

321

on quartz, these intensity values indicated that that the luminescence quantum yield of

322

U(VI) adsorbed on quartz was about three orders of magnitude larger than that on

323

chlorite, assuming that the luminescence spectra of U(VI) adsorbed on quartz and chlorite

324

have similar molar absorptivity.

325

Evaluation of both the deconvoluted luminescence spectra and the corresponding

326

normalization factors indicated that the sharp intensity drop from fCC = 0 to fCC = 0.2 was

327

more significant for U(VI) adsorbed on quartz. The subsequent intensity drop at fCC > 0.2

328

applied to U(VI) adsorbed on both quartz and chlorite (SI Figure 6).

329

concentration of 5×10-7 M, the concentration of U(VI) adsorbed on quartz decreased from

330

1.17×10-8 to 0.32×10-8 mole/g from fCC =0 to fCC = 0.2. However, the corresponding

331

luminescence spectral area dropped from 1550 to 32 based on the results of spectral

332

deconvolution. Such large disproportionality between the emission intensity and the

333

concentration of adsorbed U(VI) indicated that there was pronounced luminescence

14 ACS Paragon Plus Environment

At a U(VI)

Page 15 of 33

Environmental Science & Technology

334

quenching,38, 39 and/or self-absorption of the emitted light by Fe and Cr in chlorite.40, 41 If

335

self-absorption were the primary factor, it would be expected that adsorbed U(VI) on

336

quartz and chlorite would behave equally and that the decrease of luminescence intensity

337

would be proportional to fCC. Neither of these expectations was observed (Figure 6 and

338

SI Figure 6). Thus, the luminescence decrease with increasing fCC was likely caused by

339

luminescence quenching by Fe, Cr and other transition metal impurities in the chlorite.

340

The exact quenching mechanisms of adsorbed U(VI) luminescence by the mineral

341

mixtures was not determined. The chlorite contained both Fe (1.2%) and Cr (2.3%). The

342

total available Fe and Cr concentrations (3.8x10-3 M Fe and 8.7x10-3 M Cr) were three or

343

four orders of magnitude higher than that of U(VI) (5x10-6 M or 5x10-7 M, respectively)

344

at the given the solid-solution ratios. Assuming congruent dissolution of chlorite, the

345

dissolved Cr3+, Fe3+, and Fe2+ concentrations would be in the ranges of 0.86x10-6 M –

346

2.44x10-6 M (Cr3+) and 0.21x10-6 M – 0.59x10-6 M (both Fe2+ and Fe3+), respectively,

347

based on the measured Mg concentrations.

348

dissolved oxygen concentration could be as high as 1.4x10-3 M,42 and thus the solubilized

349

Fe2+ would be oxidized to Fe3+ by oxygen. The low Fe2+ concentration and the presence

350

of dissolved oxygen would also minimize any reduction of uranyl ion by Fe2+ in the

351

present system, such reductions had been observed with Fe-rich chlorite under anaerobic

352

conditions.43 Limited by low solubility, both Fe3+ and Cr3+ ions could exist as surface-

353

sorbed species, precipitated clusters, or ferrihydrite-like nano-particulates,44, 45 leading to

354

enhanced luminescence quenching. Indeed, trace Fe was observed in association with

355

both chlorite and quartz in the EDS elemental map of the U-bearing quartz-chlorite

Considering the aerobic conditions, the

15 ACS Paragon Plus Environment

Environmental Science & Technology

Page 16 of 33

356

mixtures (SI Figure 3). It is also possible that exposed structural and surface-adsorbed Fe

357

were active U(VI) adsorption sites in the mineral mixtures.43, 44

358

Comparison of Figures 2 and 3 showed that the increasing spectral characters of

359

U(VI) adsorbed on chlorite with increasing fCC values on the normalized luminescence

360

spectra followed the same trend as that of the fractional concentration of adsorbed U(VI)

361

in the mineral mixtures. In order to quantify the correlations between the fractional

362

U(VI) concentration in each mineral phase in the solid mixture with the corresponding

363

fractional intensity in the measured spectra, the fractional spectral intensity of U(VI)

364

adsorbed on quartz and chlorite, fS,Q and fS,CC, were calculated at all fCC values as follows,

365

f S ,Q =

AQ AQ + AUCa + AUCb

and

f S ,CC =

AUCa + AUCb AQ + AUCa + AUCb

(5)

366

where AQ, AUCa and AUCb are the integrated areas under the corresponding deconvoluted

367

luminescence spectra of U(VI) associated with quartz and chlorite (both UCa and UCb).

368

Even though the calculations employed nontrivial approximations in the absence of

369

precise determination of the quantum yields of the surface complexes, plots of the

370

calculated fractional spectral intensity as a function of fCC (Figure 7) displayed

371

approximate resemblance to the fractional adsorbed U(VI) concentrations on quartz and

372

chlorite (Figure 2).

373

function of the spectral fractions of U(VI) adsorbed on quartz and chlorite (SI Figure 7)

374

only displayed qualitative linear correlations in the fCC value range of 0.2 – 1.0 at both

375

U(VI) concentrations, and the concentration fractions of U(VI) adsorbed on quartz were

376

underestimated while those on chlorite were overestimated in all the mixtures. The latter

377

inferred that the observed negative deviation of the measured Kd values from the

378

calculated ones based on component additivity (Figure 1) had a larger contribution from

However, correlation plots of the concentration fractions as a

16 ACS Paragon Plus Environment

Page 17 of 33

Environmental Science & Technology

379

decreased U(VI) adsorption on chlorite in the mixtures. By assuming that the deviation

380

was solely due to decreased U(VI) adsorption on chlorite, the Kd contributions from

381

quartz and chlorite, Kd,Q’ and Kd,CC’ were calculated from their mass fractions as the

382

following,

383

Kd,Q’ = Kd,Q × fQ

(6)

384

Kd,CC’ = Kd - Kd,Q’

(7)

385

The resulting Kd,Q’ and Kd,CC’ values were used to calculate the concentration

386

contributions and fractional concentrations of U(VI) adsorbed on quartz and chlorite in

387

the mixtures using Eqs. (1) – (3).

388

Plots of the calculated concentration fractions as a function of fCC (SI Figiure 8)

389

displayed improved resemblance to those of the spectral fractions (Figure 7) and

390

correlation plots of the concentration fractions as a function of the spectral fractions

391

became linear across the entire fCC range with correlation coefficients of 0.95 and 0.92 at

392

U(VI) concentrations of 5 × 10-6 M and 5 × 10-7 M, respectively (SI Figure 9). These

393

results indicated that mixing quartz and chlorite primarily affected U(VI) adsorption on

394

chlorite with little impact on U(VI) adsorption on quartz even though larger U(VI)

395

luminescence quenching was observed on the latter. The approximate linear correlations

396

between the concentration fractions and the spectral fractions suggest that it is possible to

397

estimate U(VI) concentration in individual mineral phases based on the mineralogical

398

composition, total U(VI) concentration and the measured luminescence spectra, thus

399

offering credible empirical inputs for model simulation of U(VI) adsorption in mineral

400

mixtures when precise measurement is not feasible.

17 ACS Paragon Plus Environment

Environmental Science & Technology

Page 18 of 33

401

Implications Quartz is the most abundant mineral phase among the fine size

402

fraction (< 125 µm) vadose zone sediments at both the US DOE Hanford Site and

403

Naturita Site.

404

abundance, possess high surface area and strong affinities to U(VI). Their common

405

association with larger crystallites as surface coatings further highlight their role in U(VI)

406

adsorption in subsurface sediments. The present results indicate that mixing quartz and

407

chlorite leads to deviation of U(VI) adsorption properties (e.g. Kd) from what is expected

408

from component additivity model, particularly for more reactive minerals such as

409

chlorite. This implies that for natural sediments, which are aged mineral mixtures,

410

adequate corrections taking into consideration of possible alteration of the mineral

411

constituents are required to simulate U(VI) adsorption in the mineral mixture based

412

adsorption parameters obtained on the individual mineralogical components.

413

invariant spectral profiles of the primary U(VI) surface species and approximate linear

414

correlations between the fractional U(VI) concentration and spectra in the binary mineral

415

mixtures, on the other hand, suggest that with precise knowledge of the mineralogical

416

composition and overall U(VI) concentration, it is possible to predict U(VI) distribution

417

empirically in such mineral mixtures using U(VI) luminescence spectroscopy

418

measurements.

Chlorite, along with other phyllosilicates, though present with low

The

419 420

ASSOCIATED CONTENT

421

Supporting Information

422

Additional information as noted in the text. This material is available free of charge via

423

the Internet at http://pubs.acs.org.

18 ACS Paragon Plus Environment

Page 19 of 33

424 425

Environmental Science & Technology

ACKNOWLEDGEMENTS

426

The authors thank Dr. James Amonette for providing the chlorite mineral

427

specimen and Mr. Bruce Arey for SEM and EDS sample analysis. The authors are also

428

indebted to four anonymous reviewers whose insightful comments greatly helped to

429

improve the quality of the manuscript. This project was supported by the Hanford site

430

SFA Program managed by the U.S. DOE Office of Biological and Environmental

431

Research (OBER). Part of this research was performed at EMSL, a national scientific

432

user facility at PNNL managed by the Department of Energy’s Office of Biological and

433

Environmental Research. Pacific Northwest National Laboratory is operated for the U.S.

434

Department of Energy by Battelle under Contract DE-AC06-76RLO 1830.

435

19 ACS Paragon Plus Environment

Environmental Science & Technology

436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462

Table 1. Experimental data for U(VI) adsorption on quartz (Qtz)-chlorite (Chl) mixtures in pH 8.1 synthetic groundwater at 25°C. Total mineral weight = 0.2 g. Solution volume: 10 ml. Sample Qtz:Chl Surface [U]total U UAds Kd U Adsorption No. Ratio Area Adsorbed Concentration Density (m2) (M) (%) (10-8 Mole/g) (ml/g) (Mole/m2·108) 36.2 9.04 28.3 5.55 1 10:0 0.326 5.0·10-6 2. 9:1 0.346 5.0·10-6 35.6 8.90 27.6 5.15 -6 41.0 10.3 34.8 5.62 3 8:2 0.364 5.0·10 4 7:3 0.384 5.0·10-6 53.2 13.3 56.9 6.93 57.5 14.4 67.8 7.13 5 6:4 0.404 5.0·10-6 6 5:5 0.424 5.0·10-6 62.2 15.6 82.3 7.35 7 4:6 0.442 5.0·10-6 72.5 18.1 132 8.19 -6 8 3:7 0.462 5.0·10 76.1 19.0 160 8.24 80.2 20.0 202 8.33 9 2:8 0.482 5.0·10-6 10 1:9 0.500 5.0·10-6 83.7 20.9 258 8.36 11 0:10 0.520 5.0·10-6 84.9 21.2 281 8.16 -7 12 10:0 0.326 5.0·10 46.7 1.17 43.7 0.72 13 9:1 0.346 5.0·10-7 69.5 1.74 114 1.01 75.1 1.88 150 1.03 14 8:2 0.364 5.0·10-7 15 7:3 0.384 5.0·10-7 82.6 2.07 237 1.08 -7 16 6:4 0.404 5.0·10 85.8 2.14 301 1.06 17 5:5 0.424 5.0·10-7 88.8 2.22 397 1.05 18 4:6 0.442 5.0·10-7 90.4 2.26 470 1.02 -7 91.8 2.30 562 0.99 19 3:7 0.462 5.0·10 20 2:8 0.482 5.0·10-7 93.0 2.32 663 0.97 -7 21 1:9 0.500 5.0·10 94.1 2.35 793 0.94 94.6 2.36 870 0.91 22 0:10 0.520 5.0·10-7

20

ACS Paragon Plus Environment

Page 20 of 33

Page 21 of 33

463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508

Environmental Science & Technology

Figure Captions Figure 1.

Plot of measured Kd values of U(VI) adsorption in quartz-chlorite mixtures as a function of the mass fraction of chlorite in pH 8.1 synthetic groundwater at U(VI) concentrations of 5·10-6 M (filled circle) and 5·10-7 M (open circle), respectively. Solid lines are polynomial fit of the measured Kd values. Dashed lines are calculated Kd values based on the component additivity model.

Figure 2.

Simulated fractional contribution to the concentration of adsorbed U(VI) by quartz (open circle) and chlorite (filled circle) in the mineral mixtures as a function of the mass fraction of chlorite in quartz:chlorite mixtures in pH 8.1 synthetic groundwater. Total U(VI) concentrations are 5·10-6 M (A) and 5·10-7 M (B), respectively.

Figure 3.

LHeT Luminescence spectra of U(VI) adsorbed on quartz:chlorite mixtures in pH 8.1 synthetic groundwater at U(VI) concentrations of 5·10-6 M (A) and 5·10-7 M (B), respectively. All spectra were normalized to the same maximum intensity and offset along the Y-axis for clarity. λex = 415 nm.

Figure 4.

Time-resolved LHeT Luminescence spectra of U(VI) adsorbed on quartz:chlorite mixtures in synthetic groundwater, pH 8.1 at U(VI) concentrations of 5·10-6 M (A) and 5·10-7 M (B), respectively. In A, fCC = 0.4. In B, fCC = 0.3. The delay times are: a) 0.0 ms; b) 0.2 ms; c) 0.7 ms; d) 1.1 ms; e) 2.8 ms; and f) 4.0 ms. All spectra were normalized to the same maximum intensity and were offset along the Y-axis for clarity. λex = 415 nm.

Figure 5.

Deconvoluted LHeT luminescence spectra (circles) of U(VI) adsorbed on quartz:chlorite mixtures in pH 8.1 synthetic groundwater, pH 8.1 at U(VI) concentrations of 5·10-6 M (A) and 5·10-7 M (B), respectively, as the combination of U(VI) adsorbed on quartz (blue) and chlorite (green and purple). In A: fCC = 0.6. In B: fCC = 0.3. Both measured spectra were normalized to the same maximum intensity. λex = 415 nm.

Figure 6.

Luminescence intensity of U(VI) adsorbed on quartz-chlorite mixtures as a function of the mass fraction of chlorite in the mineral mixtures in pH 8.1 synthetic groundwater at U(VI) concentrations of 5·10-6 M (filled circle) and 5·10-7 M (open circle), respectively. The solid and dashed lines are fitted trend lines of the intensity data.

Figure 7.

Simulated spectral fractions of U(VI) adsorbed on quartz (filled circle) and chlorite (open circle) in the mineral mixtures as a function of the mass fraction of chlorite in pH 8.1 synthetic groundwater at U(VI) concentrations of 5·10-6 M (A) and 5·10-7 M (B), respectively.

21

ACS Paragon Plus Environment

Environmental Science & Technology

509

REFERENCES

510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552

(1) Davis, J. and Curtis, G., Application of surface complexation modeling to describe uranium (VI) adsorption and retardation at the uranium mill tailings site at Naturita, Colorado in NUREG Report CR-6820 2003, U. S. Nuclear Regulatory Commission: Washington, DC. (2) Morris, D.E., Allen, P.G., Berg, J.M., Chisholm-Brause, C.J., Conradson, S.D., Donohoe, R.J., Hess, N.J., Musgrave, J.A., and Tait, C.D. Speciation of uranium in Fernald soils by molecular. spectroscopic methods: Characterization of untreated soils. Environ. Sci. Technol. 1996, 30(7), 2322-2331. (3) Wan, J.M., Kim, Y.M., Tokunaga, T.K., Wang, Z.M., Dixit, S., Steefel, C.I., Saiz, E., Kunz, M., and Tamura, N. Spatially Resolved U(VI) Partitioning and Speciation: Implications for Plume Scale Behavior of Contaminant U in the Hanford Vadose Zone. Environ. Sci. Technol. 2009, 43(7), 2247-2253. (4) Zachara, J.M., Brown, C., Christensen, J., Dresel, E., Kelly, S., Liu, C., McKinley, J., and Um, W., A Site-Wide Perspective on Uranium Geochemistry at the Hanford Site. 2007, Pacific Northwest National Laboratory: Richland, WA. (5) Fox, P.M., Davis, J.A., and Zachara, J.M. The effect of calcium on aqueous uranium(VI) speciation and adsorption to ferrihydrite and quartz. Geochim. Cosmochim. Acta 2006, 70(6), 1379-1387. (6) Greathouse, J.A., O'Brien, R.J., Bemis, G., and Pabalan, R.T. Molecular dynamics study of aqueous uranyl interactions with quartz (010). J. Phys. Chem. B 2002, 106(7), 1646-1655. (7) Chardon, E.S., Bosbach, D., Bryan, N.D., Lyon, I.C., Marquardt, C., Römer, J., Schild, D., Vaughan, D.J., Wincott, P.L., Wogelius, R.A., and Livens, F.R. Reactions of the feldspar surface with metal ions: Sorption of Pb(II), U(VI) and Np(V), and surface analytical studies of reaction with Pb(II) and U(VI). Geochim. Cosmochim. Acta 2008, 72(2), 288-297. (8) Dong, W.M., Ball, W.P., Liu, C.X., Wang, Z.M., Stone, A.T., Bai, J., and Zachara, J.M. Influence of calcite and dissolved calcium on uranium(VI) sorption to a Hanford subsurface sediment. Environ. Sci. Technol. 2005, 39(20), 7949-7955. (9) Reeder, R., Nugent, M., Lamble, G., Tait, C.D., and Morris, D.E. Uranyl incorporation into calcite and aragonite: XAFS and luminescence studies. Environ. Sci. Technol. 2000, 34(4), 638-644. (10) Duff, M.C., Coughlin, J.U., and Hunter, D.B. Uranium co-precipitation with iron oxide minerals. Geochim. Cosmochim. Acta 2002, 66(20), 3533-3547. (11) Waite, T.D., Davis, J.A., Payne, T.E., Waychunas, G.A., and Xu, N. Uranium(VI) adsorption to ferrihydrite - application of a surface complexation model. Geochim. Cosmochim. Acta 1994, 58(24), 5465-5478. (12) Catalano, J.G. and Brown, J.G.E. Uranyl adsorption onto montmorillonite: Evaluation of binding sites and carbonate complexation. Geochim. Cosmochim. Acta. 2005, 69(12), 2995-3005. (13) Chisholm-Brause, C., Conradson, S.D., Buscher, C.T., Eller, P.G., and Morris, D.E. Speciation of uranyl sorbed at multiple binding-sites on montmorillonite. Geochim. Cosmochim. Acta 1994, 58(17), 3625-3631.

22

ACS Paragon Plus Environment

Page 22 of 33

Page 23 of 33

553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597

Environmental Science & Technology

(14) Hunter, D.B. and Bertsch, P.M. In situ examination of uranium contaminated soil particles by micro-X-ray absorption and micro-fluorescence spectroscopies. J. Radio. Nucl. Chem. 1998, 234(1-2), 237-242. (15) Wang, Z., Zachara, J.M., Gassman, P.L., Liu, C., Qafoku, O., and Catalano, J.G. Fluorescence spectroscopy of U(VI)-silicate and U(VI)-contaminated Hanford sediment. Geochim. Cosmochim. Acta 2005, 69(6), 1391-1403. (16) Zachara, J.M., Long, P.E., Bargar, J., Davis, J.A., Fox, P., Fredrickson, J.K., Freshley, M.D., Konopka, A.E., Liu, C., McKinley, J.P., Rockhold, M.L., Williams, K.H., and Yabusaki, S.B. Persistence of uranium groundwater plumes: Contrasting mechanisms at two DOE sites in the groundwater-river interaction zone. J. Contam. Hydrol. 2013, 147, 45-72. (17) Stubbs, J.E., Veblen, L.A., Elbert, D.C., Zachara, J.M., Davis, J.A., and Veblen, D.R. Newly recognized hosts for uranium in the Hanford site vadose zone. Geochim. Cosmochim. Acta 2009, 73(6), 1563-1576. (18) Palmer, D.A., Shiao, S.Y., Meyer, R.E., and Wethington, J.A. Adsorption of nuclides on mixtures of minerals. J. Inorg. Nucl. Chem. 1981, 43(12), 3317-3322. (19) Davis, J.A., Coston, J.A., Kent, D.B., and Fuller, C.C. Application of surface complexation concept to complex mineral assemblages. Environ. Sci. Technol. 1998, 32(19), 2820-2828. (20) Davis, J.A., Meece, D.E., Kohler, M., and Curtis, G.P. Approaches to surface complexation modeling of Uranium(VI) adsorption on aquifer sediments. Geochim. Cosmochim. Acta 2004, 68(18), 3621-3641. (21) Payne, T.E., Davis, J.A., Ochs, M., Olin, M., and Tweed, C.J. Uranium adsorption on weathered schist - intercomparison of modelling approaches. Radiochim. Acta 2004, 92(9-11), 651-661. (22) Waite, T.D., Davis, J.A., Fenton, B.R., and Payne, T.E. Approaches to modelling uranium(VI) adsorption on natural mineral assemblages. Radiochim. Acta 2000, 88(9-11), 687-693. (23) Wang, Z., Zachara, J., Boily, J.-F., Xia, Y.X., Resch, C.T., Moore, D., and Liu, C. Determining Individual Mineral Contributions To U(VI) Adsorption In A Contaminated Aquifer Sediment: A Fluorescence Spectroscopy Study. Geochim. Cosmochim. Acta 2011, 75(10), 2965–2979. (24) Kohler, M., Curtis, G.P., Kent, D.B., and Davis, J.A. Experimental investigation and modeling of uranium(VI) transport under variable chemical conditions. Water Resour. Res. 1996, 32(12), 3539-3551. (25) Phillips, T.L., Loveless, J.K., and Bailey, S.W. Cr3+ Coordination in chlorites structural study of 10 chromian chlorites. Am. Mineral. 1980, 65(1-2), 112-122. (26) Bond, D.L., Davis, J., and Zachara, J., Uranium(VI) release from contaminated vadose zone sediments: Estimation of potential contributions from dissolution and desorption, in Adsorption of Metals by Geomedia II: Variables, Mechanisms, and Model Applications, M.O. Barnett and Kent, D.B., Editors. 2007, Academic Press: San Diego, CA. pp. 379-420. (27) Allison, J.D., Brown, D.S., and Novo-Gradac, K.J., MINTEQA2//PRODEFA2, a geochemical assessment model for environmental systems (version 4). 1998, Environmental Research Laboratory, U.S. EPA.

23

ACS Paragon Plus Environment

Environmental Science & Technology

598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641

(28) Guillaumount, R., Fanghänel, T., Neck, V., Fuger, J., Palmer, D.A., Grenthe, I., and Rand, M.H., Update on the Chemical Thermodynamics of Uranium, Neptunium, Plutonium, Americium and Technetium. 2003, Amsterdam: Elsevier. (29) Wang, Z., Zachara, J.M., Yantasee, W., Gassman, P.L., Liu, C.X., and Joly, A.G. Cryogenic laser induced fluorescence characterization of U(VI) in Hanford vadose zone pore waters. Environ. Sci. Technol. 2004, 38(21), 5591-5597. (30) Jacquier, P., Meier, P., and Ly, J. Adsorption of radioelements on mixtures of minerals - experimental study. Appl. Geochem. 2001, 16(1), 85-93. (31) Tao, Z.Y. and Dong, W.M. Additivity rule and its application to the sorption of radionuclides on soils. Radiochim. Acta 2003, 91(5), 299-303. (32) Anderson, P.R. and Benjamin, M.M. Modeling adsorption in aluminum-iron binary oxide suspensions. Environ. Sci. Technol. 1990, 24(10), 1586-1592. (33) Anderson, P.R. and Benjamin, M.M. Surface and bulk characteristics of binary oxide suspensions. Environ. Sci. Technol. 1990, 24(5), 692-698. (34) Ilton, E.S., Wang, Z., Boily, J.-F., Qafoku, O., Rosso, K.M., and Smith, S.C. The Effect of pH and Time on the Extractability and Speciation of Uranium(VI) Sorbed to SiO2. Environ. Sci. Technol. 2012, 46(12), 6604-6611. (35) Wang, Z., Zachara, J.M., Liu, C., Gassman, P.L., Felmy, A.R., and Clark, S.B. A cryogenic fluorescence spectroscopic study of uranyl carbonate, phosphate and oxyhydroxide minerals. Radiochim. Acta 2008, 96(9-11), 591-598. (36) Del Nero, M., Galindo, C., Barillon, R., and Made, B. TRLFS Evidence for Precipitation of Uranyl Phosphate on the Surface of Alumina: Environmental Implications. Environ. Sci. Technol. 2011, 45(9), 3982-3988. (37) Gabriel, U., Charlet, L., Schlapfer, C.W., Vial, J.C., Brachmann, A., and Gabriel, G. Uranyl surface speciation in silica particles studied by time-resolved laserinduced fluorescence spectroscopy. J. Colloid Interf. Sci. 2001, 239(2), 358-368. (38) Bodenant, B., Fages, F., and Delville, M.H. Metal-induced self-assembly of a pyrene-tethered hydroxamate ligand for the generation of multichromophoric supramolecular systems. The pyrene excimer as switch for iron(III)-driven intramolecular fluorescence quenching. J. Am. Chem. Soc. 1998, 120(30), 75117519. (39) Varnes, A.W., Dodson, R.B., and Wehry, E.L. Interactions of transition-metal ions with photoexcited states of flavines. Fluorescence quenching studies. J. Am. Chem. Soc. 1972, 94(3), 946-950. (40) Maksimovic, Z., White, J.L., and Logar, M. Chromium-bearing dickite and chromium-bearing kaolinite from Teslic, Yugoslavia. Clay Clay Miner. 1981, 29(3), 213-218. (41) White, W.B. and Keester, K.L. Optical absorption spectra of iron in rock-forming silicates. Am. Mineral. 1966, 51(5-6), 774-790. (42) Lide, D.R., ed. CRC Handbook of Chemistry and Physics. 72nd ed. 1991, CRC Press: Boston. (43) Singer, D.M., Maher, K., and Brown Jr, G.E. Uranyl-chlorite sorption/desorption: Evaluation of different U(VI) sequestration processes. Geochim. Cosmochim. Acta 2009, 73(20), 5989-6007.

24

ACS Paragon Plus Environment

Page 24 of 33

Page 25 of 33

642 643 644 645 646 647 648 649

Environmental Science & Technology

(44) Arnold, T., Zorn, T., Zanker, H., Bernhard, G., and Nitsche, H. Sorption behavior of U(VI) on phyllite: experiments and modeling. J. Contam. Hydrol. 2001, 47(2-4), 219-231. (45) Banfield, J.F. and Murakami, T. Atomic-resolution transmission electron microscope evidence for the mechanism by which chlorite weathers to 1 : 1 semiregular chlorite-vermiculite. Am. Mineral. 1998, 83(3-4), 348-357.

25

ACS Paragon Plus Environment

Environmental Science & Technology

Page 26 of 33

1000

Kd(ml/g)

800

600

400

200

0 0.0

0.5

1.0

fCC

650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673

Figure 1

26

ACS Paragon Plus Environment

674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715

Environmental Science & Technology

fSolid U Conc

Page 27 of 33

1.0

1.0

0.8

0.8

0.6

0.6

A

0.4 0.2

0.2

0.0

0.0 0.0

0.2

0.4

0.6

0.8

B

0.4

1.0

0.0

0.2

fCC

0.4

0.6

0.8

1.0

fCC

Figure 2

27

ACS Paragon Plus Environment

Environmental Science & Technology

6

A

6

B FCC =

FCC = 0.0

5

Relative Intensity

716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760

Page 28 of 33

0.0

5 0.2

0.2

4

4 0.4

0.4

3

3 0.6

0.6

2

2 0.8

0.8

1

1 1.0

1.0

0

0 500

550

600

Wavelength (nm)

500

550

600

Wavelength (nm)

Figure 3

28

ACS Paragon Plus Environment

Page 29 of 33

6

A

6

B a

a 5

Relative Intensity

761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805

Environmental Science & Technology

5

b

b 4

4

c

c 3

3

d

d 2

2

e

e 1

1

f

f 0

0 500

550

600

Wavelength (nm)

500

550

Wavelength (nm)

Figure 4

29

ACS Paragon Plus Environment

600

Environmental Science & Technology

1.0

Intensity

806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847 848 849 850 851

A

1.0

0.8

0.8

0.6

0.6

0.4

0.4

0.2

0.2

0.0

0.0 500

550

600

Wavelength (nm)

Page 30 of 33

B

500

550

Wavelength (nm)

Figure 5

30

ACS Paragon Plus Environment

600

Page 31 of 33

Environmental Science & Technology

Log(Peak Area)

4

3

2

1

0 0.0

852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875 876 877

0.2

0.4

0.6

0.8

1.0

fCC

Figure 6

31

ACS Paragon Plus Environment

Environmental Science & Technology

1.0

fNormalized Spectra

878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923

1.0

A

0.8

0.8

0.6

0.6

0.4

0.4

0.2

0.2

0.0

0.0 0.0

0.5

1.0

Page 32 of 33

B

0.0

0.2

fWeight of Chlorite

0.4

0.6

0.8

1.0

fWeight of Chlorite

Figure 7

32

ACS Paragon Plus Environment

Page 33 of 33

TOC Figure

1.0

0.8

U in Chlorite

0.6 0.4

U in Quartz

0.2 0.0

Fractional U(VI) Concentration

1.0

Fractional Normalized Spectra

924 925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 940 941 942 943

Environmental Science & Technology

U in Chlorite 0.8 0.6 0.4 0.2

U in Quartz

0.0 0.0

0.5 1.0 Chlorite Mass Fraction

33

0.0

ACS Paragon Plus Environment

0.5 1.0 Chlorite Mass Fraction