Label-Free Detection of Bacillus anthracis Spore Uptake in

Sep 6, 2017 - The laser used in this study is a continuous wave (CW) 1064 nm ytterbium fiber laser (IPG Photonics, Oxford, MA) controlled by custom so...
2 downloads 11 Views 1000KB Size
Subscriber access provided by UNIVERSITY OF ADELAIDE LIBRARIES

Article

Label-free Detection of Bacillus anthracis Spore Uptake in Macrophage Cells Using Analytical Optical Force Measurements Colin G Hebert, Sean Jeffrey Hart, Tomasz A. Leski, Alex Terray, and Qin Lu Anal. Chem., Just Accepted Manuscript • DOI: 10.1021/acs.analchem.7b01983 • Publication Date (Web): 06 Sep 2017 Downloaded from http://pubs.acs.org on September 11, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Analytical Chemistry is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Analytical Chemistry

Label-free Detection of Bacillus anthracis Spore Uptake in Macrophage Cells Using Analytical Optical Force Measurements Colin G. Heberta‡ Sean Hartb, Tomasz A. Leskic, and Alex Terraya§ , Qin Lua* a

Naval Research Laboratory, Chemistry Division, Bio/Analytical Chemistry Section, Code 6112 4555 Overlook Ave. S.W. Washington, DC 20375 USA b

c

LumaCyte, LLC. 1145 River Road, Suite 16, Charlottesville, VA 22901 USA

Naval Research Laboratory, Center for Bio/Molecular Science and Engineering, Code 6910 4555 Overlook Ave. S.W. Washington, DC 20375 USA

*Corresponding Author: Qin Lu: [email protected] ‡Present address: LumaCyte, LLC. 1145 River Road, Suite 16, Charlottesville, VA 22901 USA §

Present address: MRIGlobal, 65 West Watkins Mill Road, Gaithersburg, MD 20878 USA

ACS Paragon Plus Environment

Analytical Chemistry

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

1 2 3

Abstract

4

importance with respect to both anthrax disease progression, spore detection for biodefense, as well as

5

understanding cell clearance in general. While most detection systems rely on specific molecules, such as

6

nucleic acids or proteins, and fluorescent labels to identify the target(s) of interest, label-free methods

7

probe changes in intrinsic properties, such as size, refractive index, and morphology, for correlation with

8

a particular biological event. Optical chromatography is a label free technique that uses the balance

9

between optical and fluidic drag forces within a microfluidic channel to determine the optical force on

Understanding the interaction between macrophage cells and Bacillus anthracis spores is of significant

10

cells or particles. Here we show an increase in the optical force experienced by RAW264.7 macrophage

11

cells upon the uptake of both microparticles and B. anthracis Sterne 34F2 spores. In the case of spores,

12

the exposure was detected in as little as one hour without the use of antibodies or fluorescent labels of any

13

kind. An increase in the optical force was also seen in macrophage cells treated with cytochalasin D, both

14

with and without a subsequent exposure to spores, indicating that a portion of the increase in the optical

15

force arises independent of phagocytosis. These results demonstrate the capability of optical

16

chromatography to detect subtle biological differences in a rapid and sensitive manner, and suggest future

17

potential in a range of applications, including the detection of biological threat agents for biodefense, and

18

pathogens for the prevention of sepsis and other diseases.

19 20 21 22 23

Keywords: optical chromatography, laser, microfluidic, Bacillus anthracis, macrophage

24 25 26 27 2 ACS Paragon Plus Environment

Page 2 of 29

Page 3 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Analytical Chemistry

1 2 3

Introduction

4

environmental insults, macrophages have the potential to act as a sensor indicating the onset of

5

an infection or exposure event. For this reason, the interaction between macrophages and

6

various pathogens, including Francisella tularensis,1 Salmonella enterica serovar

7

Typhimurium,2 Staphylococcus aureus,3 and Bacillus anthracis spores,4 has been the subject of a

8

number of studies. In the case of B. anthracis spores in particular, studies have predicted that

9

macrophage-mediated transport plays an important role in the spread of vegetative cells into the

As one of the body’s first lines of defense against inhalational anthrax and other

10

bloodstream and throughout the rest of the body.5,6,7 However, most tools for the detection of

11

spores or bacteria inside macrophages rely on fluorescent labeling of the bacteria through the use

12

of an antibody or other labeled molecule. While powerful in their specificity, these labels are

13

limited in several ways. In the case of fluorescent labeling of bacteria or spores, an appropriate

14

target antibody or fluorescent molecule must exist that can selectively bind the target of interest.

15

These labels can be expensive, labile (requiring special storage and transport), and limited to a

16

particular bacteria or target protein. Even using antibodies which are exquisitely sensitive, non-

17

specific interactions can still be problematic.8,9 Furthermore, if the target is changed in some

18

way, the antibody or label may no longer be able to bind, diminishing if not eliminating detection

19

capability. Finally, the labeling procedure is typically considered labor-intensive.

20

In contrast, label-free detection and characterization methods seek to surmount these

21

obstacles by utilizing the intrinsic differences between individual or populations of cells.

22

Through the exposure of cells to one or more forces, including optical,10 magnetic,11

23

mechanical,12 and electrical,13,14 these differences can be exploited to allow the separation or

24

characterization of these cells. When considering the possibility of using macrophages as the

3 ACS Paragon Plus Environment

Analytical Chemistry

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

1

basis for a sensitive detection system, either in vivo or in vitro, the ability to detect a wide range

2

of infectious threats would be highly desirable. Label-free methods facilitate this approach as it

3

may be possible to detect the response of a small but significant number of host cells, and/or a

4

general shift in the cell population that reflects an exposure event, without relying on a molecule

5

or condition specific to a certain pathogen. Once a population shift or change has been detected,

6

cells showing a shift or change can be collected and subjected to more specific confirmatory

7

analyses in order to facilitate diagnosis or treatment.

8 9

The use of optical force for manipulating and interrogating cells and microparticles has become a well-established field of study with applications in the chemical, biological, and

10

medical fields.10, 15,16,17,18,19,20 Optical chromatography is a technique which relies on the balance

11

of optical and fluidic forces in a microchannel.21,22 In contrast to other optical force techniques

12

such as optical tweezers or optical trapping that generally use a highly focused laser beam,

13

optical chromatography employs a mildly focused beam. As particles encounter the beam, they

14

experience optical pressure that results from photons imparting a fraction of their momentum as

15

they either scatter at the surface or refract through a particle. The magnitude of this force

16

depends on the size, refractive index, shape, morphology and composition of the particle,21,23

17

with higher refractive index particles experiencing a greater force. In an optical chromatography

18

system, force differentials will form the basis for characterization and separation. Thus, it is

19

important to determine and understand the optical force exerted on cells and how these optical

20

forces are influenced by cellular changes linked to specific events.

21

In this study, we present data on the optical force changes associated with the engulfment

22

of both microparticles and B. anthracis spores by macrophages, and the response of

23

macrophages to B. anthracis spores after phagocytosis was inhibited by cytochalasin D, a cell-

4 ACS Paragon Plus Environment

Page 4 of 29

Page 5 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Analytical Chemistry

1

permeable and potent inhibitor of actin polymerization. In both cases, the optical force of

2

individual macrophages increased when compared to unexposed macrophages.

3 4

Materials and Methods

5

Microchip construction The microfluidic flowcell consists of five plates of fused silica and is similar in

6 7

construction to flowcells used in previous work.24 Fluid connectors (Idex Health Sciences, Oak

8

Harbor, WA) were screwed into a custom plastic holder that aligns the fluidic connections with

9

the ports on the microfluidic chip.

10

Fluidic system The fluidic control system utilizes five pressurized control vessels filled with

11 12

approximately 1mL of liquid, generally PBS buffer (pH 7.4, Sigma, St. Loius, MO, USA), which

13

occupies about 2/3 of the vessel volume. By controlling the pressure above the liquid in each

14

vessel, pulse-free, stable and reproducible fluid flow can be achieved.25 The multi-reservoir

15

design isolates the flow system, increasing the stability and the flexibility to control the direction

16

of flow. Flow direction and flow rate were precisely measured to a resolution of ±1.5 nl/min

17

using a calibrated commercial liquid mass flow meter (Sensirion Inc., Westlake Village, CA,

18

USA).

19

Optics and imaging

20

The laser used in this study is a continuous wave (CW) 1064 nm ytterbium fiber laser

21

(IPG Photonics, Oxford, MA, USA) controlled by custom software written in Labview. The

22

laser is focused into the microfluidic system by a 0.5 inch diameter plano-convex 100 mm focal

23

length lens. Unless otherwise noted, the laser power in all situations was 3W. The microfluidic

5 ACS Paragon Plus Environment

Analytical Chemistry

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

1

flowcell is mounted on a 5 axis positioner (New Focus, San Jose, CA, USA) and the entire

2

aligned optical and fluidic system can be visualized using a 10x objective and lens tube system

3

(Infinity Photo-Optical, Boulder, CO, USA) connected to a CCD camera (Basler, Inc. Exton, PA,

4

UA) illuminated by a PL-800 fiber optic light (Edmund Optics, Barrinton, NJ, USA). The

5

camera/objective and illuminator were mounted independently of the laser, each on separate x-y-

6

z translational platforms from Thorlabs (Newton, NJ, USA). Data collection and analysis were

7

performed using StreamPix Version 5 (Norpix, Inc., Quebec, Canada).

8

Macrophage cell culture

9

RAW264.7 cells (ATCC# TIB-71) were maintained per the manufacturer’s instructions

10

in Dulbecco’s modified Eagle’s medium (ATCC, Manassas, VA, USA) supplemented with 10%

11

fetal bovine serum (Invitrogen, Carlsbad, CA, USA). Cells were grown at 37° C in a humidified

12

incubator supplemented with 5% CO2.

13

B. anthracis spore preparation

14

B. anthracis Sterne (nonpathogenic, vaccine strains) 34F2 was obtained from Colorado

15

Serum Co. (Denver, CO), and 7702 containing pRP1028 plasmid that produces Red Fluorescent

16

Protein (RFP) was provided by Dr. Molly Hughes (University of Virginia, Charlottesville, VA).

17

Spores were prepared as previously described.26 The details are given in the Supporting

18

Information.

19

Particle and spore uptake by macrophage cells

20

Macrophage cells were seeded onto 24 well plates such that a near-confluent (~95%)

21

monolayer was present after 2 days of incubation. Just prior to the addition of microparticles or

22

spores, several wells were harvested and counted in order to accurately determine the

23

multiplicity of infection (MOI) for the experiment. Subsequently, the medium was aspirated

6 ACS Paragon Plus Environment

Page 6 of 29

Page 7 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Analytical Chemistry

1

from both control and experimental wells and replaced with fresh medium. Microparticles or

2

spores (MOI of 10 or 100) were then added to the experimental wells at the appropriate

3

concentration. After the designated incubation time (3 h for microparticles or 1 h for spores),

4

cells were washed three times with PBS (pH 7.4) to remove any externally bound particles or

5

spores. Cells were detached from the well plates using trypsin and resuspended in medium prior

6

to analysis. During binding experiments, cells were incubated with fresh medium containing

7

cytochalasin D (10 µM) for 1 hour prior to the addition of spores. Spores were then added to this

8

medium directly prior to 1 hour incubation time. Microparticles used include 1.0 µm fluorescent

9

polystyrene (PS) particles (Polysciences, Warrington, PA, USA) and 2.0 µm silica (Si) particles

10

(Bangs Labs, Fishers, IN, USA). Particles per cell were determined using fluorescence (or in the

11

case of Si, brightfield) microscopy and visually counting the number of particles within each

12

cell. In the case of fluorescent spores, confocal microscopy was used to visualize the spores both

13

inside and outside the cells.

14

Optical chromatography system calibration

15

Each day before cell measurements were made, the optical chromatography system was

16

calibrated using a NIST traceable 1.8 micron PS particle (Polysciences, Warrington, PA, USA).

17

The laser alignment and the beam’s focal point inside the microchannel were calibrated by

18

trapping a representative number (N > 10) of particles at the same location against a fixed fluid

19

flow rate. This calibration ensured that a constant optical force was applied to the particle at a

20

predetermined location, countering a predetermined hydrodynamic dragging force and helping

21

minimize any drift in the trapping flow rate that might occur as a result of changes in the

22

environmental conditions within the lab.

23 24

Results and Discussion 7 ACS Paragon Plus Environment

Analytical Chemistry

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

1 2

Optical force effects from macrophage - microparticle interaction Because the size and refractive index of microparticles are well defined, they can serve as

3

an initial analog for bacillus spores or bacteria, as well as preliminary samples to test the

4

sensitivity of the system for detecting optical force changes that result from engulfed particles.

5

Two types of particles were used, PS and Si. PS particles have a refractive index of ~1.57 at

6

1064 nm,27 which is similar to that of B. anthracis (1.52828). Si particles have a lower refractive

7

index (~1.45), which is closer to that of bacterial and eukaryotic cells. Flow rates for trapping

8

unexposed RAW 264.7 macrophage cells were used as the reference. Following particle

9

engulfment, the flow rates required to trap macrophage cells at the same location against a

10 11

calibrated laser beam were measured. Cell sample (500,000 cells/ml, 200 µL) was loaded into a sample injection tube which

12

was then connected to the optical chromatography system. As individual cells entered the flow

13

cell, the laser shutter was opened, trapping cells within the beam against the fluidic flow inside

14

the channel. Once cells were trapped within the beam, the flow rate was adjusted in order to

15

balance the cells at a predetermined location (approximately 3/5 of the distance down the

16

channel and 265 µm from the focal point of the laser), at which point the flow rate was recorded.

17

When a cell is trapped, the net force acting on it is zero. Thus, the drag force and the optical

18

forces acting in opposite directions along the axis of the beam are equal (FOptical = FDrag).

19

Assuming laminar flow and a spherical cell, the drag force can be calculated using Stokes’ law:

20

FDrag = 6πηαν

21

where η is the fluid’s dynamic viscosity (N s/m2), α is the radius of the cell (m), and v is the

22

fluid flow velocity (m/s).29 Given that the fluid flow velocity is directly proportional to the drag

8 ACS Paragon Plus Environment

Page 8 of 29

Page 9 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Analytical Chemistry

1

force, it is also directly proportional to the optical force and can, therefore, be used to compare

2

individual and populations of cells.

3

A comparison between the trapping flow rate of unexposed macrophage cells and cells

4

incubated with microparticles is shown in Figure 1A. Unexposed cells have an average trapping

5

flow rate of 245 ± 26 nL/min. In comparison, cells incubated with 1.0 µm PS microparticles

6

experience the highest optical force, with an average trapping flow rate of 431± 91 nL/min.

7

Though less pronounced, cells incubated with 2.0 µm Si microparticles also had a significant (p

8

< 0.01) increase in optical force when compared to cells alone, with average trapping flow rate of

9

294 ± 34 nL/min. Cells exposed to 1.0 µm PS microparticles have the broadest histogram, with

10

the trapping flow rates of these cells ranging from 305 nL/min to 610 nL/min (Figure 1B). In

11

contrast, unexposed cells have a narrow distribution around the population average, with no cells

12

trapped at flow rate > 325 nL/min. As shown in Figure 2A, nearly all (97%) exposed cells have

13

engulfed at least one particle, with the number of particles per cell ranging from 0 to 24. On

14

average, the particles represent just ~ 0.6 percent of the volume of the cell (assuming an average

15

cell size of 10 microns), but result in a 75 percent increase in optical force, demonstrating that

16

the uptake of even a small number of particles of higher refractive index dramatically alter the

17

optical force exerted on a macrophage cell. With the highest number of particles engulfed (24),

18

the total volume of 24 particles only accounts for 2.4 percent of the cell volume, but the highest

19

flow rate measured (610 nL/min) represents a nearly 150 percent increase in the optical force.

20

Cells exposed to 2.0 µm Si microparticles show a similar distribution (Figure 2B), but a lower

21

overall number of particle uptake per cell.

22 23

To assess the impact from the change in bulk refractive index on optical force exerted on a macrophage cell after its engulfment of the microparticles, the effective refractive index of

9 ACS Paragon Plus Environment

Analytical Chemistry

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

1

exposed macrophage cells containing PS or Si microparticles can be estimated using Maxwell

2

Garnett Approximation30. It incorporates the refractive index of the macrophage cell (assumed to

3

be 1.38431) and of the particle (PS: 1.57, Si: 1.45), and the volume fraction calculated from the

4

number of particles per cell. Table 1 gives the average trapping flow rate, particles per cell, force

5

experienced by and the refractive indices of the unexposed cell population and those exposed to

6

PS and Si microparticles. Particles per cell were determined using microscopy and the force was

7

calculated using the Stokes’ law, assuming a spherical shape for the cells. There is minimal

8

difference between unexposed and exposed cells in terms of average effective refractive indices

9

using the average number of particles per cell, presumably due to the low volume fraction of

10

engulfed microparticles, 0.6% for 1.0 µm PS and 1.8% for 2.0 µm Si. At the highest number of

11

uptake, the volume fractions reached 2.4 % for 1.0 µm PS and 8.8% for 2.0 µm Si, but the

12

increase in average effective refractive index in both cases is still negligible (~ 0.001).

13

Since we cannot attribute the increase in optical force solely to a change in refractive

14

index brought about by the physical presence of the particles, there must be other changes in the

15

exposed cells due to their interactions with the microparticles that affect the optical force. With

16

regards to the phagocytosis of PS and Si microparticles by macrophages, some suggest that the

17

uptake of these particles is mediated by a macrophage receptor with collagenous structure

18

(MARCO), one of the scavenge receptors on the surface of macrophages.32,33 Others hypothesize

19

that the uptake of PS or Si microparticles is via a nonspecific mechanism involving surface

20

charge interaction. Furthermore, it is believed that the phagocytosis of non-opsonized particles is

21

likely the interplay of microtubules, microtubule associated proteins, and actin nucleation

22

factors.34 Despite the complexity associated with different phagocytic mechanisms, a number of

23

shared features follow: particle internalization is initiated by the interaction of specific receptors

10 ACS Paragon Plus Environment

Page 10 of 29

Page 11 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Analytical Chemistry

1

on the surface of the phagocyte with ligands on the surface of the particle. This leads to the

2

polymerization of actin at the site of ingestion, and the internalization of the particle via an actin-

3

based mechanism.35 Evidence exists that the actin polymerization is essential for the

4

phagocytosis of and biological response to the PS and Si microparticles.36, 37

5

Optical force effects from macrophage - B. anthracis Sterne strain spore interaction

6

Following the success achieved in sensitively measuring the change in optical force

7

associated with the engulfment of microparticles by macrophage cells, experiments were directed

8

towards the assessment of any change in optical force that results from the interaction of

9

macrophage cells with more pertinent bioparticles, B. anthracis Sterne strain spores. Cell

10

populations were analyzed in the same manner, except that the incubation time was decreased

11

from three hours down to one hour. Results shown in Figure 3 compare the trapping flow rate of

12

unexposed cells with cells incubated with B. anthracis spores at an MOI of 10 or 100. The

13

average trapping flow rate (Figure 3A) increased from 250 ± 26 nL/min for unexposed cells to

14

278 ± 37 nL/min and 375 ± 107 nL/min for cells incubated with spores at an MOI of 10 and 100,

15

respectively. A significant (p < 0.01, t-test) increase in the average trapping flow rate, thus the

16

optical force, was measured in cells incubated with spores at both MOIs. The relatively large

17

standard deviation of the MOI 100 population is a result of the high degree of heterogeneity in

18

the population, likely due to a wide distribution of the number of spores taken up by each cell.

19

This heterogeneity between cells can be seen when looking at the histogram data for each cell

20

population (Figure 3B). When compared to unexposed cells, the MOI 10 population has a slight

21

broadening of the peak in the direction of higher optical force, as reflected by a greater

22

percentage of cells trapped at a flow rate > 300 nL/min. At MOI 100, the histogram reflects not

23

only a further increase in trapping flow rate (and thus optical force), but also a wide variability

11 ACS Paragon Plus Environment

Analytical Chemistry

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

1

between cells in the population. In fact, 50% of the cells were trapped at a flow rate > 350

2

nL/min, stretching all the way up to 867 nL/min. This variability at MOI 100 is not unexpected,

3

as previous studies using fluorescent labels have shown that the number of spore uptake at MOI

4

100 can range from 2 to 22, with an average of 9.9 ± 4.6 spores per cell. In contrast, the number

5

of spores per cell at MOI 10 ranges from 0 to 5, with an average of 0.9 ± 1.2 spores per cell.4

6

Thus, the increase in the variability and magnitude of the optical force when moving from MOI

7

10 to MOI 100 observed in this study correlates well with previously published reports.4

8

However, it is important to note that in contrast to previous studies, no antibodies or fluorescent

9

labels were required to measure the difference in optical forces and to distinguish the unexposed

10

cells from the exposed cells in this study.

11

The size of Bacillus anthracis spores has been measured using a transmission electron

12

microscope26 to have a width of 0.71 µm and a length of 1.28 µm. The refractive index of the

13

spore has been determined to be 1.528.28 Using the Maxwell Garnett Approximation30 and

14

taking the highest number of uptake, 22, to calculate the volume fraction of spores inside the

15

cell, the change in refractive index is, once again, negligible. Thus, as in the case of

16

microparticle phagocytosis, the increase in optical force experienced by the macrophage cells

17

exposed to spores cannot be attributed solely to the change in refractive index brought about by

18

the physical presence of the spores.

19

In addition to increased optical force, cells exposed to spores often displayed increased

20

laser scatter. Figure 4 compares an unexposed cell trapped in the beam at 267 nL/min (Figure

21

4A) to an exposed cell at MOI 100 trapped at 867 nL/min (Figure 4B). The latter image displays

22

such a large degree of scattered light that it is difficult to even view the actual cell. Interestingly,

23

our results contrast with side scatter measurements from a traditional flow cytometer which

12 ACS Paragon Plus Environment

Page 12 of 29

Page 13 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Analytical Chemistry

1

reported little to no difference between untreated cells and those exposed to B. anthracis Sterne

2

spores at similar MOIs4.

3

block the laser beam (Figures 4C and 4D, respectively). The unexposed cell can clearly be seen,

4

while the exposed cell at MOI 100 is blurred as a result of a much higher trapping flow rate and,

5

thus, the speed at which it exits the trap. It is important to note that there is little to no size

6

difference between the unexposed and exposed cells, suggesting that the increase in optical force

7

is not driven predominantly by the size change, but rather other factors such as cell membrane

8

characteristics, or changes in the cytoskeleton as a result of spore engulfment.

9

Each cell is also shown after it is released by closing the shutter to

The binding and uptake of Bacillus anthracis spores by macrophage cells is a dynamic

10

process and involves multiple receptors and signaling pathways. The recognition of exosporium

11

glycoprotein of Bacillus collagen-like protein of anthracis (BclA) by the integrin Mac-1

12

receptor, and the binding of rhamnose residues of BclA by the CD-14 co-receptor which induces

13

an inside-out signaling pathways involving TLR2 and PI3K, ultimately leads to enhanced Mac-1

14

dependent spore internalization.38 The changes in the cell membrane and the cytoskeleton due to

15

the binding of spores by the multiple receptors, the activation of multiple signaling pathways, the

16

polymerization of actin, and the physical presence of spores inside the macrophages, all of these

17

combined, will induce significant changes in cell surface characteristics. Atomic Force

18

Microscope investigation on fixed RAW264.7 macrophage cells39 stimulated by

19

lipopolysaccharide (LPS) has revealed that the cell surface roughness was increased compared to

20

unstimulated ones, presumably due to the aggregation of membrane proteins and the change of

21

F-actin structure. Rough surfaces scatter more light than smooth surface, and macrophage cells

22

exposed to spores displayed increased laser scatter (Figure 4 B). Even though no AFM images

23

are available on macrophage cells exposed to spores, it is reasonable to assume that the exposed

13 ACS Paragon Plus Environment

Analytical Chemistry

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

1

cells have rougher cell surface than unexposed ones, since the binding and uptake of spores also

2

involves the interplay of multiple membrane proteins and the change of actin structure. The

3

increased optical force on macrophage cells exposed to spores, therefore, is likely linked to the

4

increase in cell surface roughness.

5

Optical force effects from macrophage- B. anthracis spore interaction in absence of phagocytosis

6

Because an optical force increase was observed following exposure of macrophage cells

7

to B. anthracis spores, experiments were conducted to determine to what extent the increase was

8

driven by changes to the macrophage cell itself, as opposed to the physical presence of the spores

9

inside the cell. To this end, cells were incubated with 10 µM cytochalasin D, an inhibitor of

10

actin-dependent uptake pathways such as phagocytosis, prior to incubation with B. anthracis

11

spores. As an additional control, the optical force of cells exposed to only cytochalasin D was

12

also measured. Results presented in Figure 5A show a slight but statistically significant (p