Ligand-Based Phase Control in Porous Molecular Assemblies - ACS

Mar 26, 2018 - Functionalization of isophthalic acid ligands with linear alkoxide groups from ethoxy through pentoxy is shown to have a pronounced eff...
0 downloads 5 Views 2MB Size
Subscriber access provided by UNIV OF SCIENCES PHILADELPHIA

Ligand-Based Phase Control in Porous Molecular Assemblies Omar Barreda, Gianluca Bannwart, Glenn P. A. Yap, and Eric D. Bloch ACS Appl. Mater. Interfaces, Just Accepted Manuscript • DOI: 10.1021/acsami.8b02015 • Publication Date (Web): 26 Mar 2018 Downloaded from http://pubs.acs.org on March 27, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 17 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Ligand-Based Phase Control in Porous Molecular Assemblies Omar Barreda,‡ Gianluca Bannwart,‡ Glenn P. A. Yap,‡ Eric D. Bloch*,‡,§ ‡Department of Chemistry and Biochemistry, University of Delaware, Newark, Delaware 19716, United States §Center for Neutron Science, Department of Chemical and Biomolecular Engineering, University of Delaware, Newark, Delaware 19716, United States KEYWORDS porous solids, gas adsorption, metal-organic materials, hydrocarbon separation, two-dimensional materials

ABSTRACT Functionalization of isophthalic acid ligands with linear alkoxide groups from ethoxy through pentoxy is shown to have a pronounced effect on both the synthesis of porous paddlewheel-based molecular assemblies and their resulting surface areas and gas adsorption properties. Shorter chain length is compatible with either tetragonal or hexagonal twodimensional materials, with the hexagonal phase favored with longer chain length. Precise tuning of reaction conditions affords discrete molecular species that are soluble in a variety of organic solvents. The isolated porous molecules display BET surface areas ranging from 125 to 545 m2/g. The pentoxide-based molecular assembly shows considerable promise for the separation of

ACS Paragon Plus Environment

1

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 2 of 17

hydrocarbons with average isosteric heats of adsorption of –48 and –31 kJ/mol for ethylene and ethane, respectively.

As a result of their solubility,1,2 amenability to postsynthetic modification and purification,3,4 and potential mobility in the solid state,5 porous molecular materials have received considerable recent attention.6,7,8,9 Although the surface areas typically displayed by these discrete molecular solids fall short of the record values exhibited by porous network solids such as aluminosilicates,10 metal-organic frameworks (MOFs),11 and covalent organic frameworks (COFs),12 surface areas approaching 4000 m2/g have recently been achieved.13,14,15 As such, they have shown utility for a wide variety of applications ranging from gas storage and separation to catalysis.16,17 Additionally, all-organic porous molecules were utilized in the preparation of the first porous liquid.18 These latter materials, typically referred to as porous organic cages (POCs), lack the metal sites that endow hybrid organic-inorganic materials with selective adsorption. Porous coordination complexes, often referred to as metal-organic polyhedra,19,20 ,21,22 nanoballs,23 nanocages,24 or supramolecular assemblies,25,26 lie at the interface of POCs and MOFs as they are discrete molecular assemblies and contain both metal and organic building units. Indeed, selective gas adsorption and BET surface areas in excess of 1100 m2/g have been reported for these materials.27,28,29 Although they are molecular by nature, the number of porous metal-organic compounds shown to display appreciable solubility, one of the main advantages of porous molecular assemblies, are minimal.30,31,32,33 For the synthesis of porous, soluble molecular assemblies, we reasoned that the options were to either target new structure types or modify the isophthalic acid ligands that M24L24 carboxylate-based materials are typically comprised of. The 5-position of isophthalic acid serves as an easy entry point for the latter strategy as a wide variety of functionalized ligands are

ACS Paragon Plus Environment

2

Page 3 of 17 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Figure 1. Reaction scheme illustrating the synthesis of two-dimensional layered materials and discrete, intrinsically porous molecular assemblies. Here routes a and b in formamide/ethanol mixtures afford tetragonal and hexagonal phases at room temperature and elevated temperatures, respectively. Utilization of dialkylformamide/ethanol solvent mixtures affords discrete cages (route c). commercially available. In our hands, most of these ligands afforded nearly insoluble materials or molecules devoid of permanent porosity. The reaction of copper salts with 5hydroxyisophthalic acid, however, affords Cu_OH-bdc,34 a material with excellent solubility in methanol. Further, this ligand is easily functionalized via reaction with alkyl halides to afford 5alkoxy-isophthalic acid ligands. As is typical for the synthesis of new metal-organic materials, we initially surveyed the reaction of alkoxide-functionalized ligands with copper(II) under a variety of conditions, varying solvent, concentration, reaction time, and copper source. Previous studies have suggested that the formation of carboxylate-based cuboctahedral cages is incredibly rapid at room temperature in the presence of base,35 with crystallization considerably slower. The room temperature reaction

ACS Paragon Plus Environment

3

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 4 of 17

of 5-ethoxy-benzenedicarboxylic acid (OEt-bdc) with copper acetate in 1:1 formamide/ethanol mixtures via layering of metal and ligand solutions afforded rectangular crystals at the solution/solution interface after 1 day (See Supporting Information for full experimental procedures). Single-crystal structural determination indicated the material adopts the 2dimensional structure previously reported.36 This solid is comprised of copper paddlewheel units coordinated to four different ligands (Figure 1). Ligands located trans to each other across the paddlewheel are pointed in alternating directions throughout the structure which results in a 2dimensional framework featuring square channels based on stacked sheets. A parallel reaction isolated after 72 hours was found to contain hexagonal crystals. This material crystallizes in P–3m1 with a = b = 18.725(4) and c = 6.999(2) and is similarly comprised of copper paddlewheel units. Viewed down the a-axis, these two structures appear nearly identical. However, this framework adopts a Kagome lattice featuring a trihexagonal tiling of pores.37,38 In this structure, the ethoxide groups point into the hexagonal channel. In order to determine if there was a transition from Cu_OEt-bdc_tet to Cu_OEt-bdc_hex over the course of the reaction or if two different phases formed in separate reaction vials as a result of minute changes in concentration, solvent volume, etc. the reaction was repeated for a single vial. Indeed, after 24 hours at room temperature we observed tetragonal crystals in the reaction vessel (phase purity was later confirmed via powder X-ray diffraction-Figure S2). After an additional 24 hours, the single-crystal quality tetragonal crystals appeared as poorly formed crystallites. Ultimately, after a total reaction time of 72 hours, we exclusively observed single-crystal quality hexagonal plates. This observation is in stark contrast to previous results wherein only tetragonal 2dimensional metal-organic frameworks were observed for the direct synthesis of various 5substituted isophthalic acid-based materials.36

ACS Paragon Plus Environment

4

Page 5 of 17 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Closer inspection of the structures depicted in Figure 1 reveals that in the hexagonal phase significantly more space is accessible for the alkoxide groups on the ligands. Incorporation of longer alkane groups should steer product formation toward the hexagonal phase. To investigate this, we prepared three additional alkoxide-functionalized ligands featuring propoxy, butoxy, and pentoxy groups. For OPr-bdc, similar time-dependent product distribution is observed. The resulting structures adopt similar unit cells to those observed for both Cu_OEt-bdc materials. The OEt-bdc and OPr-bdc hexagonal sheets reported here are isostructural to those recently reported wherein they were synthesized via the hydrolytic decomposition of discrete molecular assemblies.39 An abrupt transition was observed upon moving to the butoxy-substituted ligand. Here we isolated both phases as pure products by simply controlling reaction concentration, with the tetragonal phase favored at lower concentrations. For OPent-bdc it was particularly difficult to isolate phase-pure tetragonal crystals. Under all conditions that were attempted we observed, at best, 10 % tetragonal-phase formation. This is likely a result of the incompatibility of this ligand with the limited inter-ligand space present in this structure. Although reaction time and reagent concentration can be used to alter product distribution, the formamide/ethanol solutions we used were not ultimately compatible with the formation of discrete molecular assemblies, the ethoxide- and propoxide-functionalized versions of which were recently reported.39 For the synthesis of Cu_OEt-bdc, the reaction of copper nitrate with one equivalent of H2OEt-bdc in a 60:40 DMF/EtOH solution at 92 °C for 12 hours afforded crystalline material in high yield. Similar reaction conditions were utilized for the synthesis of Cu_OPent-bdc and Cu_OPr-bdc. For the former, solid crystalized after heating at 100 °C for 12 hours. For the latter, an 80:20 DMA/EtOH mixture was utilized. The synthesis of Cu_OBu-bdc required dramatically different synthesis conditions, as we typically obtained phase-impure

ACS Paragon Plus Environment

5

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 6 of 17

Figure 2. Space-filling representation of Cu_OPr-bdc illustrating porosity intrinsic to individual cages and extrinsic porosity between cages. material contaminated with an unknown crystalline material. Ultimately, the room temperature reaction of copper acetate with one equivalent of ligand in pure DMF for 24 hours afforded crystalline solid. (See Supporting Information for full experimental details) All four molecular species reported here adopt the previously reported structure type wherein 24 ligands and 12 dicopper paddlewheel units assemble into a cuboctahedron (Figure 2).39 This is comprised of eight triangular faces and six square faces with the ligands on the edges and metal clusters at the vertices. No obvious structural correlations can be made between ligand functional group and space group, the details of which can be found in Table S14. However, there is a clear trend in increasing unit cell volume from the shortest chain to the longest. Further, the intermolecular distance, measured here as the shortest distance between an atom located in the center of adjacent molecules, increases from ethoxy to propoxy to butoxy from 23.6 to 29.1 Å as longer alkoxide groups on the ligands space the cages out at further distances. The distance in Cu_OPent-bdc decreases significantly as a result of the favorable alkane–arene interaction in this

ACS Paragon Plus Environment

6

Page 7 of 17 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

structure (Figure S17). Here, six of the pentoxy groups on a plane in the structure interact with six adjacent cages, essentially forming a two-dimensional array of cuboctahedra. There are large solvent-accessible voids in the crystal structures of all four materials. Accordingly, thermal gravimetric analysis (TGA) of as-synthesized samples reveal mass losses ranging from 15 wt. % for Cu_OPent-bdc to 40 wt. % for Cu_OEt-bdc (Figure S5). To desolvate these materials solvent exchanges were attempted with a variety of solvents, including DMF, DMA, methanol, and ethanol. However, their high solubility in hot amide-based solvents and solvent mixtures prevented the use of these for exchanges. Ultimately, room temperature diethyl ether exchanges were utilized. With the exception of the previously reported chromium(II)-based material, Cr_tBu-bdc,28,29 these types of molecular assemblies have typically shown limited thermal stability in terms of their optimal activation temperatures. Accordingly, we initiated degas surveys for all four compounds at room temperature. Although Cu_OEt-bdc and Cu_OPrbdc displayed Langmuir surface areas above 300 m2/g upon activation at room temperature, the butoxy- and pentoxy-functionalized materials had significantly diminished surface areas. We therefore screened activation conditions up to 200 ºC in 25 ºC increments. Both Cu_OEt-bdc and Cu_OPr-bdc achieved optimal surface areas after activation at 125 ºC. The surface areas of Cu_OBu-bdc and Cu_OPent-bdc were optimized at significantly higher temperatures of 150 and 175 ºC, respectively. All four materials displayed decreased surface areas upon heating to 200 ºC. Fits to N2 adsorption data at 77 K result in BET (Langmuir) surface areas ranging from 125545 (280-727) m2/g with increasing alkoxide functionalization resulting in lower surface areas (Table S14). The potential benefits of soluble porous materials are particularly illustrated by Cu_OPent-bdc. During activation condition screening we obtained a nonporous phase at high degas temperature. By dissolving this material in chloroform and allowing the solvent to slowly

ACS Paragon Plus Environment

7

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 8 of 17

Figure 3. Ethane (upper left) and ethylene (upper right) adsorption isotherms at 298 K for CuOEt-bdc (red), Cu_OPr-bdc (blue), Cu_OBu-bdc (orange), and Cu_OPent-bdc (green). Isosteric heats of adsorption for ethane (lower left) and ethylene (lower right) in these materials. evaporate over the course of two days, crystalline material isostructural to the solvothermally prepared material was isolated. This recrystalized material displays similar surface area as the starting compound (Figure S14) Although the surface areas displayed by the four materials reported here are modest compared to both metal-organic frameworks and many porous molecular cages, the alkoxidefunctionalization on the surface of the molecules are intriguing for selective gas adsorption. These types of functional groups have been shown to impart selective adsorption properties in previously reported metal-organic frameworks.40 To assess the ability of Cu_OR-bdc porous cages to selectively adsorb ethane or ethylene, isotherms were collected at 298, 308, and 318 K. For both gases, Cu_OEt-bdc displays the highest saturation capacity at room temperature approaching 2 mmol/g, nearly double that of the other materials (Figure 3). Interestingly, there is not a straightforward relationship between one bar uptakes and surface areas as, although the latter decrease with increasing alkoxide length, the former follows the trend Et > Pent > Prop >

ACS Paragon Plus Environment

8

Page 9 of 17 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

But. Ultimately, the combination of surface area and ligand functionalization dictate the saturation capacity. Isosteric heats of ethane and ethylene adsorption were calculated using the Clausius–Clapeyron equation and are plotted in Figure 3. All four materials display similar ethane binding enthalpies ranging from ~30-35 kJ/mol up to a loading of 0.5 mmol/g. The ethoxide–, propoxide–, and butoxide–functionalized cages are all expected to show limited ethylene/ethane selectivity as their ethylene adsorption enthalpies similarly fall in the range from 33-40 kJ/mol. Cu_OPent-bdc, however, shows a significantly higher ethylene adsorption enthalpy averaging 48 kJ/mol from 0-0.5 mmol/g, as compared to 31 kJ/mol for ethane. To our knowledge, this represents the first case of olefin/paraffin selectivity displayed by a porous molecular assembly. The foregoing results demonstrate the use of isophthalic acid functionalization to control phase formation in low-dimensional metal-organic materials. The limited ligand bulk in the ethoxide– and propoxide–functionalized materials allows for the isolation of tetragonal sheets, hexagonal sheets, and discrete molecules, depending on synthesis conditions. The four discrete porous cages display BET surface areas ranging from 125-545 m2/g. In addition to affecting the phase of the material that is formed, the functional groups also impart selective adsorption properties in the materials as Cu_OPent-bdc displays high selectivity for the adsorption of ethylene over ethane. Based on results presented here, we expect discrete, porous metal-organic assemblies to be the favored phase in cases where functionalization in the 5-position is longer than a butoxide group. Future work along these lines will target the synthesis of selective materials with increased capacity as compared to the solids presented here.

ACS Paragon Plus Environment

9

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 10 of 17

ASSOCIATED CONTENT Supporting

Information.

The

following

files

are

available

free

of

charge.

Detailed experimental details, adsorption data and fitting, NMR and infrared spectra, thermogravimetric analysis plots, and crystal structure information (PDF). AUTHOR INFORMATION Corresponding Author *[email protected] ORCID Eric D. Bloch: 0000-0003-4507-6247 Author Contributions The manuscript was written through contributions of all authors. All authors have given approval to the final version of the manuscript. ACKNOWLEDGMENT We are grateful to the University of Delaware for generous start-up funds. REFERENCES (1) Kohl, B.; Rominger, F.; Mastalerz M. Crystal Structures of a Molecule Designed Not to Pack Tightly. Chem. Eur. J. 2015, 21, 17308-17313. (2) Briggs, M. E.; Cooper, A. I. A Perspective on the Synthesis, Purification, and Characterization of Porous Organic Cages. Chem. Mater. 2017, 29, 149-157.

ACS Paragon Plus Environment

10

Page 11 of 17 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

(3) Jiang, S.; Chen. L.; Briggs, M. E.; Hassel, T.; Cooper, A. I. Functional Porous Composites by Blending with Solution-Processable Molecular Pores. Chem. Commun. 2016, 52, 6895-6898. (4) Briggs, M. E.; Slater, A. G.; Lunt, N.; Jiang, S.; Little, M. A.; Greenaway, R. L.; Hasell, T.; Battilocchio, C.; Ley, S. V.; Cooper, A. I. Dynamic Flow Synthesis of Porous Organic Cages. Chem. Commun. 2015, 51, 17390-17393. (5) Holst, J. R.; Trewin, A.; Cooper, A. I. Porous Organic Molecules. Nat. Chem. 2010, 2, 915920. (6) McKeown, N. B. Nanoporous Molecular Crystals. J. Mater. Chem. 2010, 20, 10588-10597. (7) Tian, J.; Thallapally, P. K.; McGrail, B. P. Porous Organic Molecular Materials. CrystEngComm. 2012, 14, 1909-1919. (8) Giri, N.; Davidson, C. E.; Melaugh, G.; Del Popolo, M. G.; Jones, J. T. A.; Hasell, T.; Cooper, A. I.; Norton, P. N.; Hursthous, M. B.; James, S. J. Alkylated Organic Cages: From Porous Crystals to Neat Liquids. Chem. Sci. 2012, 3, 2153-2157. (9) Mastalerz, M. Modular Synthesis of Shape-Persistent Organic Cage Compounds: Molecular Precursors for a New Class of Permanent Porous Materials. Synlett. 2013, 24, 781786. (10) Wang, H.; Wang, Z.; Huang, L.; Mitra, A.; Holmberg, B.; Yan, Y. High-Surface-Area Zeolitic Silica with Mesoporosity. J. Mater. Chem. 2001, 11, 2307-2310.

ACS Paragon Plus Environment

11

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 12 of 17

(11) Farha, O. K.; Eryazici, I.; Jeong, N. C.; Hauser, B. G.; Wilmer, C. E.; Sarjeant, A. A.; Snurr, R. Q.; Nguyen, S. T.; Yazaydin, A. O.; Hupp, J. T. Metal-Organic Framework Materials with Ultrahigh Surface Areas: Is the Sky the Limit? J. Am. Chem. Soc. 2012, 134, 15016-15021. (12) Uribe-Romo, F. J.; Hunt, J. R.; Furukawa, H.; Klock, C.; O’Keeffe, M.; Yaghi, O. M. A Crystalline Imine-Linked 3-D Porous Covalent Organic Framework. J. Am. Chem. Soc. 2009, 131, 45704571. (13) Cooper, A. I. Molecular Organic Crystals: From Barely Porous to Really Porous. Angew. Chem. Int. Ed. 2012, 51, 7892-7894. (14) Mastalerz, M.; Oppel, I. M. Rational Construction of an Extrinsic Porous Molecular Crystal with an Extraordinary High Specific Surface Area. Angew. Chem. Int. Ed. 2012, 51, 5252-5255. (15) Zhang, G.; Presly, O.; White, F.; Oppel, I. M.; Mastalerz, M. A. A Permanent Mesoporous Organic Cage with an Exceptionally High Surface Area. Angew. Chem. Int. Ed. 2014, 53, 15161520. (16) Kewley, A.; Stephenson, A.; Chen, L.; Briggs, M. E.; Hasell, T.; Cooper, A. I. Porous Organic Cages for Gas Chromatography Separations. Chem. Mater. 2015, 27, 3207-3210. (17) Hasell, T.; Miklitz, M.; Stephenson, A.; Little, M. A.; Chong, S. Y.; Clowes, R.; Chen, L.; Holden, D.; Tribello, G. A.; Jelfs, K. E.; Cooper, A. I. Porous Organic Cages for Sulfer Hexafluoride Separation. J. Am. Chem. Soc. 2016, 138, 1653-1659.

ACS Paragon Plus Environment

12

Page 13 of 17 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

(18) Giri, N.; Del Popolo, M. G.; Melaugh, G.; Greenaway, R. L.; Ratzke, K.; Koschine, T.; Pison, L.; Costa Gomes, M. F.; Cooper, A. I.; James, S. L. Liquids with Permanent Porosity. Nature 2015, 527, 216-220. (19) Eddaoudi, M.; Kim, J.; Wachter, J. B.; Chae, H. K.; O’Keeffe, M.; Yaghi, O. M. Porous Metal-Organic Polyhedra: 25Å Cuboctahedron Constructed from 12 Cu2(CO2)4 Paddle-Wheel Building Blocks. J. Am. Chem. Soc. 2001, 123, 4368-4369. (20) Ke, Y.; Collins, D. J.; Zhou, H.-C. Synthesis and Structure of Cuboctahedral and Anticuboctahedral Cages Containing 12 Quadruply Bonded Dimolybdenum Units. Inorg. Chem. 2005, 44, 4154-4156. (21) Furukawa, S.; Horiki, N.; Kondo, M.; Hijikata, Y.; Carne-Sanchez, A.; Lerpent, P.; Louvain, N.; Diring, S.; Sato, H.; Matsuda, R.; Kawano, R.; Kitagawa, S. Rhodium-Organic Cuboctahedra as Porous Solids with Strong Binding Sites. Inorg. Chem. 2016, 55, 10843-10846. (22) Teo, J. M.; Coghlan, C. J.; Evans, J. D.; Tsivion, E.; Head-Gordon, M.; Sumby, C. J.; Doonan, C. J. Hetero-Bimetallic Metal-Organic Polyhedra. Chem. Commun. 2016, 52, 276-279. (23) Moulton, B.; Lu, J.; Mondal, A.; Zaworotko, M. J. Nanoballs: Nanoscale Faceted Polyhedra with Large Windows and Cavities. Chem. Communn. 2001, 863-864. (24) Niu, Z.; Fang, S.; Liu, X.; Ma, J.-G.; Ma, S.; Cheng, P. Coordination-Driven Polymerization of Supramolecular Nanocages. J. Am. Chem. Soc. 2015, 137, 14873-14876. (25) Chatterjee, B.; Noveron, J. C.; Resendiz, M. J. E.; Liu, J.; Yamamoto, T.; Parker, D.; Cinke, M.; Nguyen, C. V.; Arif, A. M.; Stang, P. J. Self-Assembly of Flexible Supramolecular

ACS Paragon Plus Environment

13

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 14 of 17

Metallacyclic Ensembles: Structures and Adsorption Properties of Their Nanoporous Crystalline Frameworks. J. Am. Chem. Soc. 2004, 126, 10645-10656. (26) Cook, T. R.; Stang, P. J. Recent Developments in the Preparation and Chemistry of Metallacycles and Metallacages via Coordination. Chem. Rev. 2015, 115, 7001-7045. (27) Ni, Z.; Yassar, A.; Antoun, T.; Yaghi, O. M. Porous Metal-Organic Truncated Octahedron Constructed from Paddlewheel Squares and Terthiophene Links. J. Am. Chem. Soc. 2005, 127, 12752-12753. (28) Park, J.; Perry, Z.; Chen, Y. -P.; Bae, J.; Zhou, H. C. Chromium(II) Metal-Organic Polyhedra as Highly Porous Materials. ACS Appl. Mater. Interfaces 2017, 9, 28064-28068. (29) Lorzing, G. R.; Trump, B. A.; Brown, C. M.; Bloch, E. D. Selective Gas Adsorption in Highly Porous Chromium(II)-Based Metal-Organic Polyhedra. Chem. Mater. 2017, 29, 85838587. (30) Furukawa, H.; Kim, J.; Ockwig, N. W.; O’Keeffe, M.; Yaghi, O. M. Control of Vertex Geometry, Structure Dimensionality, Functionality, and Pore Metrics in the Reticular Synthesis of Crystalline Metal-Organic Frameworks and Polyhedra. J. Am. Chem. Soc. 2008, 130, 1165011661. (31) Li, J.-R.; Timmons, D. J.; Zhou, H.-C. Interconversion between Molecular Polyhedra and Metal-Organic Frameworks. J. Am. Chem. Soc. 2009, 131, 6368-6369. (32) Lu, W.; Yuan, D.; Yakovenko, A.; Zhou, H.-C. Surface Functionalization of MetalOrganic Polyhedron for Homogeneous Cyclopropanation Catalysis. Chem. Commun. 2011, 47, 4968-4970.

ACS Paragon Plus Environment

14

Page 15 of 17 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

(33) Park, J.; Sun, L.-B.; Chen, Y.-P.; Perry, Z.; Zhou, H.-C. Azobenzene-Functionalized Metal-Organic Polyhedra for the Optically Responsive Capture and Release of Guest Molecules. Angew. Chem. Int. Ed. 2014, 53, 5842-5846. (34) Li, J.-R.; Zhou, H.-C. Bridging-Ligand-Substitution Strategy for the Preparation of MetalOrganic Polyhedra. Nat. Chem. 2010, 2, 893-898. (35) Larsen, R. W. How Fast Do Metal-Organic Polyhedra Form in Solution? Kinetics of [Cu2(5-OH-bdc)2L2]12 Formation in Methanol. J. Am. Chem. Soc. 2008, 130, 11246-11247. (36) Abourahma, H.; Bodwell, G. J.; Lu, J.; Moulton, B.; Pottie, I. R.; Bailey Walsh, R.; Zaworotko, M. J. Coordination Polymers from Calixarene-Like [Cu2(Dicarboxylate)2]4 Building Blocks: Structural Diversity via Atropisomerism. Cryst. Growth Des. 2003, 3, 513-519. (37) Perry, J. J.; McManus, G. J.; Zaworotko, M. J. Sextuplet Phenyl Embrace in a MetalOrganic Kagome Lattice. Chem. Commun. 2004, 2534-2535. (38) Mallick, A.; Garai, B.; Diaz Diaz, D.; Banerjee, R. Hydrolytic Conversion of a MetalOrganic Polyhedron into a Metal-Organic Framework. Angew. Chem. Int. Ed. 2013, 52, 1375513759. (39) Garai, B.; Mallick, A.; Das, A.; Mukherjee, R.; Banerjee, R. Self-Exfoliated MetalOrganic Nanosheets through Hydrolytic Unfolding of Metal-Organic Polyhedra. Chem. Eur. J. 2017, 23, 7361-7366. (40) Schneemann, A.; Bloch, E. D.; Henke, S.; Llewellyn, P. L.; Long, J. R.; Fischer, R. A. Influence of Solvent-Like Sidechains on the Adsorption of Light Hydrocarbons in Metal-Organic Frameworks. Chem. Eur. J. 2015, 21, 18764-18769.

ACS Paragon Plus Environment

15

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Paragon Plus Environment

Page 16 of 17

16

Page 17 of 17 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces



ACS Paragon Plus Environment