Mapping Global Flows of Chemicals: From Fossil Fuel Feedstocks to

Jan 24, 2018 - We provide the most up to date, comprehensive and transparent data set available publicly, on virgin production routes in the chemical ...
0 downloads 6 Views 2MB Size
Subscriber access provided by University of Leicester

Policy Analysis

Mapping global flows of chemicals: from fossil fuel feedstocks to chemical products Peter Levi, and Jonathan M. Cullen Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.7b04573 • Publication Date (Web): 24 Jan 2018 Downloaded from http://pubs.acs.org on January 30, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 25

Environmental Science & Technology

2

Mapping global flows of chemicals: from fossil fuel feedstocks to chemical products

3

Authorship

4

Peter G. Levi a* and Jonathan M. Cullen a

5

*Corresponding author: [email protected]

6

a

7

Abstract

8

Chemical products are ubiquitous in modern society. The chemical sector is the largest industrial energy consumer and

9

the third largest industrial emitter of carbon dioxide. The current portfolio of mitigation options for the chemical sector

1

Department of Engineering, University of Cambridge, Trumpington Street, Cambridge, CB2 1PZ, United Kingdom

10

emphasises upstream ‘supply-side’ solutions, whilst downstream mitigation options, such as material efficiency, are

11

given comparatively short shrift. Key reasons for this are the scarcity of data on the sector’s material flows, and the

12

highly intertwined nature of its complex supply chains. We provide the most up to date, comprehensive and

13

transparent dataset available publicly, on virgin production routes in the chemical sector: from fossil fuel feedstocks to

14

chemical products. We map global mass flows for the year 2013 through a complex network of transformation

15

processes, and by taking account of secondary reactants and by-products, we maintain a full mass balance throughout.

16

The resulting dataset partially addresses the dearth of publicly available information on the chemical sector’s supply

17

chain, and can be used to prioritise downstream mitigation options.

18

1. Introduction

19

Industrial chemicals and their derivatives pervade modern society. Although often diffuse in their application (e.g.

20

pharmaceuticals), the bulk outputs of the chemical and petrochemical sector – hereafter the chemical sector – are

21

deployed in huge volumes to make millions of tonnes per year (Mt yr-1) of chemical products, such as fertilizers and

22

plastics. Our industrialised economy is dependent on chemicals.

23

In performing this pivotal role, the chemical sector exerts a large environmental burden. It is responsible for

24

approximately 7% of global anthropogenic global greenhouse gas (GHG) emissions, and 5.5% when just counting CO2

25

emissions.1 The sector’s final energy consumption is the largest among industrial sectors: 42.5 EJ in 2014, of which 25 EJ

1

ACS Paragon Plus Environment

Environmental Science & Technology

Page 2 of 25

26

is feedstock energy.2 Other sources of emissions include those stemming directly from the chemical transformations

27

mobilised in reactors (process emissions), and from energy conversion in the transformation sector (indirect emissions).

28

In addition to these gaseous emissions, chemical products can spawn pernicious aqueous discharges. The oft-publicised

29

problem of fertilizer run-off contributing to hypertrophication,3 and the more recent exposition of plastic waste ending

30

up in the world’s oceans4,5 and organisms6 are notable examples.

31

This environmental strain magnifies as demand rises – the International Energy Agency (IEA) projects a 2.8-fold increase

32

in demand for the sector’s 18 most energy-intensive chemicals by 2050.1 The IEA also estimate that to maintain a ‘2DS’

33

trajectory (in which there is a 50% chance of limiting global mean temperature rise to 2 degrees Celsius above pre-

34

industrial levels), a 30% reduction in direct industrial CO2 emissions by 2050 is required, relative to 2014 levels.2, p.166

35

Without a disproportionate emissions reduction elsewhere, achieving a 30% cut in absolute chemical sector emissions

36

levels while sustaining a 2.8-fold increase in output, means a 75% reduction in emissions per unit of production by

37

2050. This is a daunting task for a competitive industrial sector in which efficiency gains are already incentivised by

38

exposure to fuel and feedstock price volatility.

39

1.1 Current options for reducing feedstock energy consumption

40

Theoretical estimates made by Neelis et al. reveal the chemical sector’s overall exothermicity – i.e. if fully captured, the

41

energy released in processing chemical feedstocks would be sufficient to supply all process energy requirements. 7 This

42

seems to be reflected by the increase of feedstock energy as a share of the sector's total energy input; from 44% in

43

1971 to 58% in 2013. However, this could be because of changes to reporting regimes used to compile these statistics.

44

A countervailing downward pressure on the share of feedstock energy is process yield improvement. However, this

45

lever is constrained by stoichiometry, and in many cases process yields are close to practical limits, leaving only a

46

marginal (and hard-won) improvement potential. The quantity, and importance of feedstock energy is likely to continue

47

growing. In their latest annual modelling effort, BP seem to concur, stating that ‘non-combusted fuel use becomes the

48

largest source of fossil fuel demand growth towards [2035]’,8, p.17 in part because of ‘limited scope for efficiency gains’8,

49

p.27

50

This prognosis is uncontroversial, and there is little disagreement around the prescriptions for mitigation. Broadly

51

speaking, three main decarbonisation levers receive most attention: feedstock and fuel substitution (including

52

biomass),9–14 process energy efficiency potential7,15–19 and innovative low carbon technologies1,20,21 (including Carbon

53

Capture and Storage (CCS)). These prescriptions are all ‘upstream’ measures, i.e. closer to the supply-side and the

in the petrochemical sector.

2

ACS Paragon Plus Environment

Page 3 of 25

Environmental Science & Technology

54

producer. ‘Downstream’ mitigation options, i.e. those closer to the demand-side and the consumer, receive

55

comparatively scarce attention. Material efficiency strategies, whereby the same service is provided with less material –

56

thereby reducing material demand – are a key group of downstream mitigation options. Allwood and Cullen22 explore

57

several strategies for bulk materials, including light-weighting and process yield improvement, but even among the

58

vanguard of global energy modelling efforts, sophisticated chemical sector analyses tend to be restricted to the

59

recycling of certain plastics.2,23–25

60

Pioneering material and end-use efficiency analyses relating to the chemical sector are not without incidence. Worrell

61

et al.26, Hekkert et al.27 and Gielen28 examined some of the key sectors (fertilizer, plastic packaging) and strategies

62

(efficient application, recycling) available downstream of the chemical sector. Scholarship in these areas has not

63

evolved much since. The main reason for this is the complexity of the sector’s supply chain, and the subsequent lack of

64

publicly available material flow data. There is an urgent need for a mass-balanced and transparently-compiled account

65

of the sector’s main material flows, so that reliable estimates of the impacts of downstream mitigation options can be

66

made. Until this gap in the literature is addressed, these options will remain under-represented relative to their

67

potential in recommendations to policy makers.

68

1.2 Chemical sector data: few and far too costly

69

This work follows similar studies of the steel29 and aluminum30 industries, but the dearth of public data on the chemical

70

sector has made it substantially more challenging. We suppose three principal reasons for the inferior data landscape.

71

Firstly, the chemical sector is a complex multi-sector industry, despite its aggregated accounting entries in energy

72

statistics.31,32 Its outputs are numerous and diverse, supplying a wide variety of material and energy services. Secondly,

73

the International Council of Chemical Associations (ICCA), a trade association and ‘worldwide voice of the chemical

74

industry’,33 falls short of its counterparts in the steel (worldsteel)34 and aluminium (International Aluminium Institute)35

75

industries on data provision. These metal industry associations’ data were instrumental in the steel and aluminium

76

studies cited above. Some reliable subsets of data on the chemical sector have been identified, such as those from the

77

International Fertilizer Association (IFA)36 and Plastics Europe37, but these tend to be fragmented with respect to their

78

sectoral and geographic coverage. Lastly, the comprehensive data that are collected on the sector are proprietary and

79

highly commoditised. Such databases are generally not available for use in academic studies; this analysis being no

80

exception.

3

ACS Paragon Plus Environment

Environmental Science & Technology

Page 4 of 25

81

1.3 Components of mapping in previous studies

82

For our stated purpose – establishing a firm basis on which to appraise downstream mitigation options – a sufficiently

83

detailed, globally balanced and publicly available map of the chemical sector is required. No such map has been

84

identified in the academic or grey literatures. However, several elements of chemical sector mapping have been

85

conducted as components of previous studies for, broadly speaking, three purposes: examining the robustness of

86

emissions and energy statistics; compiling emissions estimates associated with the non-energy use of fossil fuels; and to

87

inform bottom-up energy modelling efforts for the sector. In this section, we highlight salient studies with a focus on

88

the mapping work involved.

89

Bottom-up analyses of the main feedstock consuming processes in the chemical sector are employed to scrutinise top-

90

down international energy statistics on non-energy use, such as an international study38 by Weiss et al. and a Dutch

91

study39 by Neelis & Pouwelse. Multiple reporting irregularities are identified, and each study indicates a need for

92

increasing the quality of chemical sector energy statistics. Studies with similar findings stem from a broader energy

93

efficiency analysis of European industry by Worrell et al.40 in the early 1990s, and are most recently echoed nearly two

94

decades later by Saygin et al.41 in their analysis of the German chemical sector. These studies contain partial data on

95

feedstock energy consumption, upstream chemicals production, installed capacity and feedstock requirements. With

96

the exception of the latter41 they focus on upstream chemical production, thereby providing little information on the

97

majority of the sector’s material flows. In all cases the mapping work is the means rather than the end, and is either

98

undisclosed, insufficiently detailed or limited in scope.

99

Neelis et al.42 construct a NEAT (Non-energy Emissions Accounting Table) model to compile CO2 emission estimates

100

associated with non-energy use flows, which is employed to analyse Korea,43 Italy,44 Germany45 and the Netherlands.46

101

By better describing the degree to which non-energy consuming products are oxidised during or after use, the model

102

allows the authors to improve emissions inventories, relative to those compiled with the IPCC reference approach

103

available at the time.47 The model requires production and trade data for 77 organic and 18 inorganic chemicals, which

104

the authors acknowledge is an extensive data requirement. The country studies prove it is possible, but only with close

105

cooperation from national statistical offices or consultancies. No intermediate mapping data are presented in the

106

country-level studies.

107

The MATTER (MATerials Technologies for greenhouse gas Emission Reduction) project in the late 1990s may have

108

represented peak of ambition with regards to integrated energy and materials climate change mitigation research.

4

ACS Paragon Plus Environment

Page 5 of 25

Environmental Science & Technology

109

Kram et al.48 summarise the overall MATTER project findings: the inclusion of demand-side options (e.g. material

110

efficiency and substitution) alongside supply-side options (e.g. wind turbines and solar panels) hastens progress

111

towards, and brings down the costs of emissions mitigation. Groenendaal & Gielen49 summarise a sector-specific study

112

of the petrochemical sector. In a related project, Joosten50 examines plastic flows in the Netherlands using national

113

supply and use statistics. Each provides a contemporary snapshot of aspects of the petrochemical industry, and some of

114

the most detailed energy and materials maps of the industry identified in the literature. However; only Western Europe

115

is covered (where data are relatively plentiful and publicly available); some important feedstock-consuming chemicals

116

such as ammonia are excluded; and the studies are nearly 30 years old.

117

Other elements of chemical sector mapping are identified in: industrial energy51 and exergy52 efficiency studies; specific

118

analyses of plastics flows;53 broader analyses of chemical sector energy consumption and emissions in the UK54 and

119

globally;14,55,56 and in flowcharts published by trade associations.57,58 However, among the existing information we have

120

examined, no mapping component or selection thereof is sufficient to provide us with the framework we require. This is

121

not a criticism of studies where this was not their purpose. The remainder of this study outlines the methodology

122

(section 2) used to assemble the mapping results (section 3) required to fill this gap in the literature. In section 4, we

123

use comparisons and a sensitivity analysis to critically examine our results.

124

2. Methodology

125

This section contains an overview of the methods used to construct a dataset of global chemical sector mass flow. A

126

snapshot of the Material Flow Analysis (MFA)-based dataset is presented as a Sankey diagram – a complementary

127

pairing of analytical tools for supply chain analyses.59–62 The full details of the dataset are delineated in the Supporting

128

Information (SI) accompanying this article. After outlining the scope of the analysis, this section summarises the

129

upstream and downstream calculations sequentially.

130

2.1 Analysis scope

131

The temporal (2013) and geographic (global) boundaries of this study are chosen to align with common reporting

132

intervals for production statistics, and to negate the need to consider trade. 2013 is recent enough to construct a

133

contemporary picture of the industry, but not so recent as to limit data availability. Stocks of products within the supply

134

chain boundary are assumed to be negligible, based on evidence for several chemicals where supply and demand

135

information is available.63 Furthermore many of the sector’s products are gaseous and/or toxic, incurring hefty expense

5

ACS Paragon Plus Environment

Environmental Science & Technology

Page 6 of 25

136

when stored. ‘In-use’ stocks are not considered in static analyses, but any subsequent dynamic analysis would need to

137

take account of varying product lifetimes, especially for plastics.

138

Only virgin production routes and fossil fuel feedstocks are considered. Secondary production routes (those based on

139

recyclate) and alternative feedstocks form a small fraction of overall inputs to the sector. Global demand for plastics – a

140

subset of chemical products for which scalable secondary and bio-based routes exist – is currently estimated at 311 Mt

141

yr-1.37 Global inputs of plastic recyclate are of the order of 10 Mt yr-1, and total bioplastic production capacity is

142

approximately 1.7 Mt yr-1.51,64-65

143

The European Chemicals Agency (ECHA) keeps an inventory of commercially manufactured chemicals. The entries

144

currently number 106,213, ranging from fertilizer pre-cursors produced on the 1011 kg scale, such as ammonia, to

145

powerful analgesics administered in dosages on the 10-6 kg scale, such as fentanyl.66 Clearly a narrower focus is

146

required. Just 18 chemicals account for 63% and 75% of the sector’s process energy consumption and GHG emissions

147

respectively.1 Tracing these chemicals and their main derivatives downstream to chemical products results in the

148

inclusion of 77 chemicals and 65 processes. We return to assess the degree of coverage achieved in section 4.

149

2.2 Mapping upstream chemical production

150

The upstream portion of the dataset maps inputs of fossil fuel feedstocks to the sector’s largest-volume chemicals, the

151

salient details of which are described under the headings below.

152

Ammonia and methyl alcohol

153

Although promising carbon-free routes to ammonia and methyl alcohol are available via various types of electrolysis,67

154

the vast majority of global capacity is based on natural gas, oil product (naphtha, LPG etc.) and coal feedstocks. We

155

apply estimates of feedstock input percentages68 to production figures36,69 to get tonnages of ammonia (120.5, 14.4,

156

and 34.8 Mt yr-1) and methyl alcohol (50.3, 1.9, and 10.7 Mt yr-1) produced globally from natural gas, oil and coal

157

respectively.

158

Generalised stoichiometric expressions are formulated to characterise the ammonia and methyl alcohol production

159

processes, which each comprise synthesis gas (syngas) production and chemical synthesis steps. We assume the

160

chemical synthesis steps are consistent irrespective of the feedstock used, but distinguish between Steam Methane

161

Reforming (SMR) and Partial Oxidation (POX) syngas units. The water gas shift and reverse water gas shift reactions,

162

employed to obtain the appropriate CO:H2 syngas ratios for each feedstock/product combination, are integrated within

6

ACS Paragon Plus Environment

Page 7 of 25

Environmental Science & Technology

163

the syngas production characterisations. All terms in the generalised stoichiometric expressions can be described

164

precisely with chemical notation (NH3, CO2 etc.), apart from the feedstock inputs, which are non-uniform combinations

165

of carbon/hydrogen (C/H), and some non-C/H content. Generalised characterisations in the form CHn are used, where

166

‘n’ determines the average carbon-to-hydrogen ratio of the feedstock’s constituent molecules. Appl70 and Rainer et al.71

167

provide feed and product profiles for several real-world syngas plants. From multiple plants’ feed data, typical values of

168

n for natural gas, oil and coal feeds of 3.951, 1.873 and 0.456 were calculated. The terms are then combined and

169

balanced, resulting in the full stoichiometric expressions for each product and process route.

170

The mass proportions of the terms in the balanced stoichiometric expressions, along with the global production

171

estimates above, are used to calculate corresponding quantities of feedstocks, secondary reactants and secondary

172

products. Aggregated loss terms are incorporated to account for imperfect conversion and selectivity at the syngas and

173

chemical synthesis steps, and any non-C/H content transiting the process. Typical syngas conversion efficiencies – the

174

higher heating value (HHV) of the CO/H2 product relative to that of the feedstock input – were computed using typical

175

HHV values for each fuel72 and the syngas profile data:70,71 86.1% for natural gas (SMR), 80.8% for oil (POX) and 76.0%

176

for coal (POX). There are also small losses at the synthesis steps, described by the chemical yield: 98.0% for ammonia73

177

and 99.0% for methyl alcohol syntheses.74 These calculation steps result in a global mass-balance for ammonia and

178

methyl alcohol production. For more information, see section 4 of the SI.

179

Steam cracking

180

Capacity (in Mt yr-1 of ethylene) and feed (in percentages of ethane, naphtha etc.) data for 277 steam crackers were

181

taken from the Oil & Gas Journal’s annual surveys.75,76 Estimates were made for omitted data, using adjacent countries’

182

or regions’ figures. Typical yield profiles for steam crackers run on various feeds are provided by the European

183

Commission.77 The following identity describes the relationship between theses quantities:

184

𝑦𝑎,1 𝑦𝑏,1 𝐹𝑡 ∙ 𝑦𝑐,1 ⋮ [ 𝑦𝑖,1

𝑦𝑎,2 𝑦𝑏,2 𝑦𝑐,2 ⋮ 𝑦𝑖,2

𝑦𝑎,3 𝑦𝑏,3 𝑦𝑐,3 ⋮ 𝑦𝑖,3

⋯ 𝑦𝑎,𝑛 𝑓1 𝑃𝑎 ⋯ 𝑦𝑏,𝑛 𝑓2 𝑃𝑏 ⋯ 𝑦𝑐,𝑛 ∙ 𝑓 = 𝑃𝑐 3 ⋱ ⋮ ⋮ ⋮ ⋯ 𝑦𝑖,𝑛 ] [𝑓𝑛 ] [ 𝑃𝑖 ]

(1)

185 186

Where F t is the total quantity of all feeds in Mt yr-1, P a - i are capacities of each product (ethylene, propylene etc.) in Mt

187

yr-1, y i , n is the yield of product ‘i’ from a unit of feed ‘n’ and f 1 - n are the fractions each feed forms of F t .

7

ACS Paragon Plus Environment

Environmental Science & Technology

Page 8 of 25

188

The results of using [1] – first by solving for F t using one known production quantity (say P a ), and then using F t to

189

compute the quantities of the remaining products P b - i – are in capacity rather than production terms. An average

190

utilisation rate was estimated using global ethylene production data published by the Japanese government,63 and

191

applied to the capacity-based profile to obtain production quantities. For more information, see section 5 of the SI.

192

BTX aromatics and C4 olefins

193

C4 olefins are co-produced alongside ethylene and propylene in steam crackers run on both light (e.g. ethane) and

194

heavy (e.g. naphtha) feeds, as opposed to the BTX (benzene, toluene and xylene) aromatics, which are only produced

195

when cracking heavier feedstocks. The remaining quantities of BTX aromatics and C4 olefins produced globally are

196

mainly recovered from various refining processes’ raffinate and pyrolysis gasoline streams, such as those from fluid

197

catalytic crackers and catalytic reformers. Bender78,79 provides recent global average estimates of the proportions of C4

198

olefins and BTX aromatics obtained from each of these sources.

199

BTX aromatics streams often undergo further transformation after extraction. Principal among these transformations is

200

the conversion of toluene to xylene and benzene, via hydrodealkylation and disproportionation. Burdick and Leffler80

201

provide typical feed and product profiles for each process. For more information, see sections 6-7 of the SI.

202

On-purpose technologies

203

Multi-product processes, such as steam cracking, may not yield products in a ratio equal to that of their demands. On-

204

purpose technologies can help address such an imbalance, by producing products in a complementary ratio, or one at a

205

time. Three on-purpose technologies are characterised in this mapping work: propane dehydrogenation (PDH),

206

metathesis (MTS) and methanol-to-olefins (MTO). These flexibility-enhancing technologies’ capacities are relatively

207

small (