Subscriber access provided by University of Newcastle, Australia
Article
Massively Enhanced Electroosmotic Transport in Nanochannels Grafted with End-Charged Polyelectrolyte Brushes Guang Chen, and Siddhartha Das J. Phys. Chem. B, Just Accepted Manuscript • DOI: 10.1021/acs.jpcb.7b00493 • Publication Date (Web): 21 Mar 2017 Downloaded from http://pubs.acs.org on March 26, 2017
Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.
The Journal of Physical Chemistry B is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.
Page 1 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
Massively Enhanced Electroosmotic Transport in Nanochannels Grafted with End-charged Polyelectrolyte Brushes 1
Guang Chen and Siddhartha Das∗ Department of Mechanical Engineering, University of Maryland, College Park, MD-20742, USA E-mail:
[email protected];Phone:+1-301-405-6633
2
Abstract
3
We establish that nanochannels grafted with pH-responsive, end-charged polyelec-
4
trolyte (PE) brushes demonstrate a massive augmentation in the strength of the elec-
5
troosmotic (EOS) transport in presence of an external electric field. This contradicts
6
the existing understanding that the EOS transport is severely retarded in channels
7
grafted with the PE brushes due to the brush-induced enhanced drag force. Our math-
8
ematical model, developed on the basis of the fact that the ion concentration polar-
9
ization (ICP) effect can be neglected, explains this enhancement of the EOS transport
10
by noting that the end-charged PE brushes demonstrate a unique ability of localizing
11
the electric double layer (or the EDL) or equivalently localizing the maximum charge
12
density of the electrolyte ions at the location of its end, i.e., away from the grafting
13
surface. Accordingly, the maximum EOS driving force on the liquid, which is propor-
14
tional to this charge density, can be maximum at a location far away from the wall.
15
As a consequence, the resulting local EOS velocity suffers very little retardation due
16
to the wall shear stress enabling such massive augmentation of the EOS transport.
1
ACS Paragon Plus Environment
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1
We anticipate that the present paper will unravel a completely new paradigm in the
2
employment of functionalized interfaces in regulating the nanofluidic transport for a
3
myriad of applications.
Page 2 of 38
4
Introduction
5
Functionalization of nanochannels by grafting them with charged polyelectrolyte (PE) molecules
6
in a fashion such that these molecules attain a brush like architecture 1–3 has received wide
7
attention for applications ranging from sensing of biomolecules and analytes 4–6 to developing
8
nanofluidic current rectifiers, 7,8 ionic diodes, 9,10 and flow valves. 11 It is a standard knowledge
9
that nanochannels and microchannels grafted with PE brushes will invariably lower the flow
10
strength (e.g., electric-field-driven electroosmotic or EOS flow) on account of an enhanced
11
drag on the flow by the polymer molecules. 12–14 Studies have proposed to use this flow-
12
strength reduction for designing EOS flow suppressors 13,14 that can be useful for a number
13
of applications (e.g., bio-analyte sensing, current rectification, etc.) where appropriate and
14
highly sensitive measurement of the ionic current becomes necessary.
15
In this study, we report our discovery of a completely opposite effect of the PE-brush-
16
grafted nanochannels on the EOS transport – we demonstrate that nanochannels grafted
17
with PE-brushes containing charges only at their non-grafted ends may actually experience
18
a massive augmentation of the strength of the EOS flow. These end-charged PE brushes are
19
characterized by density of their end charges – such brushes are typically synthesized by end-
20
functionalizing long polymer chains (e.g., poly-ethylene glycol or PEG chains) with charged
21
terminal groups 15,16 and has been used for a variety of applications such as disassembling
22
amyloid fibrils, 15 targeted pH-responsive drug delivery, 17 etc. In the present paper, therefore,
23
we consider a design where the EOS transport is studied in a nanochannel whose walls
24
are grafted with such end-charged PE brushes. We show that particularly for large salt
25
concentration, the EOS flow in a PE-brush-free nanochannel, having the same surface charge
26
density (as the charge density of the ends of the end-charged PE brushes) at its rigid walls, is 2
ACS Paragon Plus Environment
Page 3 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
1
significantly weaker than the strength of the EOS flow in this end-charged PE-brush-grafted
2
nanochannels (see Fig. 1). We attribute this highly non-intuitive effect to the fact that the
3
end-charged brushes, particularly for large salt concentration (or thin electric double layer
4
or EDL), allow a localization of the EDL or equivalently a localization of the maximum
5
charge density of the electrolyte ions (i.e., the maximum difference between the number
6
densities of counterions and coions forming the EDL) at a location that is far from the
7
grafting surface. As a consequence, the driving EOS body force on the liquid, which is
8
proportional to this charge density gradient, can be highest (or most concentrated) at a
9
location where the drag on the flow caused by the wall shear stress is very small. This, in
10
turn, ensures a massive augmentation of the EOS flow strength. For charged nanochannels
11
with no brushes, this maximum driving force (or equivalently, the maximum difference in
12
the charge density) is at the wall where the no-slip condition retards the flow. On the
13
other hand, for the PE brush with backbone charges, the body force is distributed along
14
the brush height and therefore gets dispersed and does not remain localized away from the
15
wall (unlike the end-charged PE brushes). As a consequence, impact of the EOS body force
16
in driving the flow is somewhat reduced in both brush-free nanochannels and nanochannels
17
grafted with backbone-charged brushes. This justifies this rather remarkable finding where
18
the EOS flow gets enhanced in nanochannels functionalized by end-charged PE brushes. In
19
this context, it is useful to discuss the study by Yeh et al., 18 which showed that the EOS
20
transport in a nanopore is significantly augmented in case the entire membrane (containing
21
the nanopore) is end-grafted with PE brushes, as compared to the case where only the inner
22
walls of the nanopore are grafted with the PE brushes. Of course, Yeh et al. considers
23
a uniformly-charged PE brush without pH regulation. But the most important difference
24
of the findings of our paper with respect to the paper by Yeh et al. is that we show that
25
such velocity augmentation is possible in PE-brush grafted nanochannels as compared to
26
nanochannels that do not contain any brush at all and this is extremely significant given the
27
standard notion of velocity reduction due to the presence of the brushes.
3
ACS Paragon Plus Environment
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1
Page 4 of 38
In addition to discovering this highly non-trivial behavior of the PE-brush-grafted nanochan-
2
nels in context of the EOS transport, the present paper provides the first model that accounts
3
for the thermodynamics and the configuration of the PE brushes in a mean field setting for
4
modelling the EOS flow in the PE-grafted-nanochannels. There have been a considerable
5
number of studies on the EOS transport in PE-grafted nanochannels ranging from probing
6
of the streaming current generation 12,19–21 and suppressed EOS transport 13,14 to quantifying
7
the influence of the Donnan potential. 22,23 However, in all of these studies the height of the
8
PE brush layer has been assumed to be constant with no dependence on the salt concentra-
9
tion or the pH. On the contrary, in this present study we account for the effect of the salt
10
concentration and the pH on the brush configuration by describing the brush height explicitly
11
as an interplay of the elastic, excluded volume, and electrostatic energies of the brush and
12
the EDL energy. As a consequence, we embark upon a more complete model where the EOS
13
transport depends not only on the EOS body force resulting from the ion concentrations
14
but also on the specificities (e.g., strength of the drag force, location of the end charge, etc.)
15
associated with the ion concentration regulated brush height. The second critical issue is the
16
description of the monomer distribution along the PE brush. While these monomers being
17
uncharged (for the present problem) do not contribute to the overall electrostatics, they
18
indeed dictate the drag coefficient that affects the EOS transport. Previous studies on the
19
fluid flow in the PE brush grafted channels have considered a uniform or a parabolic or a cu-
20
bic monomer distribution. 13,19–23 For the present study, we shall simply consider a uniform
21
monomer distribution that is equivalent to the consideration of the well-known monomer
22
step profile proposed by Alexander 24 and de Gennes. 25,26 Therefore, in summary the mean
23
field model developed here is coupled with the appropriate description of the fluid flow in
24
order to propose the nanofluidic-transport-enhancing capabilities of the PE-brush-grafted
25
nanochannels that can be potentially employed for engineering novel nanofluidic concepts.
4
ACS Paragon Plus Environment
Page 5 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
Figure 1: Schematic depicting the electroosmotic transport in (a) nanochannels free of PE brushes and (b) nanochannels grafted with end-charged PE brushes. The schematic categorically represents the enhancement of the strength of the EOS transport in nanochannels grafted with end-charged PE brushes under the condition that the charge density at the walls (of brush-free nanochannels) is identical to that of the end charges of the end-charged-brush grafted nanochannels.
5
ACS Paragon Plus Environment
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 6 of 38
1
Brush Configuration: Thermodynamics
2
We consider an EOS transport in presence of an axial electric field in nanochannels (of height
3
2h) grafted with pH-responsive, end-charged PE brushes, as shown in Fig. 1. End-charged
4
brushes contain charges at their non-grafted ends. This end-charging depends on the pH-
5
dependent ionization of the functional group that ionizes to produce the end charge. For
6
example, consider end-charged PE brushes made up of PEG chains end-functionalized with a
7
sulphonic acid 15 or a carboxylic acid group 16 – such end-charge brushes will demonstrate pH-
8
dependent ionization and charging due to the pH-dependent charging of these end groups. In
9
this section, we shall discuss the thermodynamics that will provide the brush configuration
10
and the resulting EDL electrostatics. This model has already been discussed in details in
11
our previous papers; 27,28 therefore, we shall only provide the key ideas of the model for the
12
sake of the continuity.
13
We start by expressing the free energy (F ) of the PE-brush-surrounding-electrolyte system:
F = FB + FEDL = FB,els + FB,EV + FB,elec + FEDL ,
(1)
14
where FB is the total energy associated with the brush with FB,els , FB,EV , and FB,elec being
15
the elastic, excluded volume and electrostatic components of that energy, and FEDL is the
16
energy associated with the surrounding EDL. Here we consider an Alexander-de Gennes
17
model of “stepped” brush profile (i.e., the monomer concentration φ = 1 along the chain
18
and φ = 0 outside the chain) in order to quantify the elastic and the excluded volume energies
19
of the brush. Accordingly, FB,els 3 d2 , = kB T 2 Np a2k
(2)
ωNp2 σ FB,EV = , kB T d
(3)
20
21
where σ ∼ 1/ℓ2 is the grafting density (ℓ is the lateral separation between grafted PE
22
brushes), ak is the Kuhn length of the polymer, Np is the polymer size, kB T is the thermal 6
ACS Paragon Plus Environment
Page 7 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
(1−2χ) 3 ak 2
(where χ is the Flory exponent).
1
energy, d is the equilibrium brush height, and ω =
2
Finally, the electrostatic energy of the PE brush can be expressed as 27–29 1 (ψs σch,pH ) , σ
FB,elec =
(4)
3
where ψs = ψ (ye ) (here ye is the location of the charged end of the PE brush and ψ is the
4
electrostatic potential) and σch,pH = σch K ′ +nKa+ (ye ) is the charge density (in units of C/m2 ) of
′
a
H
5
the charged end of the PE-brush (see the appendix for the detailed derivation of this expres-
6
sion of σch,pH ). Here σch represents the maximum possible charge density, nH + = nH + (ye )
7
is the local hydrogen ion number density at the location of the end of the PE brush, and
8
Ka′ = 103 NA Kaa (where NA is the Avogadro number and Ka is the ionization constant of
9
the group located at the PE brush end whose ionization causes the charging of the brush
10
11
12
end). Eq.(4) has been derived by Tsori et al.; 29 we briefly re-derive it here for the sake of continuR ity. The electrostatic energy of a standard PE brush can be expressed as FB,elec = ρe ψd3 r
13
(where ρe is the charge density or charge per unit volume of the PE brush). Since for the
14
present case the brush is end-charged, we can write ρe = σch,pH δ(y − ye ) (where δ is the delta
15
function). Consequently, considering average area associated with each brush as ℓ2 or 1/σ,
16
we can obtain eq.(4) as the expression for the electrostatic energy of the end-charged PE
17
brush from the above expression of FB,elec .
18
19
This charge on the brush end will trigger an EDL, whose energy (for the nanochannel bottom
20
half) can be expressed as:
FEDL
1 = σ
Z
0
fEDL (ψ, ψ ′ , ni )dy. −h
7
ACS Paragon Plus Environment
(5)
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1
Page 8 of 38
Here fEDL is the EDL energy per unit volume expressed as: 28 ε0 εr dψ 2 fEDL = − | | + eψ (n+ − n− + nH + − nOH − ) 2 dy n− n+ − 1 + n− ln −1 +kB T n+ ln n+,∞ n−,∞ nOH − nH + − 1 + nOH − ln −1 . +kB T nH + ln nH + ,∞ nOH − ,∞
(6)
2
In the right hand side of eq.(6), the first to the third terms respectively represent the self-
3
electrostatic energy of the EDL, the electrostatic energy due to the charges on the electrolyte
4
ions, and the mixing entropy of the ions. Here ni (i = ±, H + , OH − ) is the number density
5
of ion of type i, ni,∞ is the bulk number density of ion of type i, kB T is the thermal energy,
6
ψ is the EDL electrostatic potential, ǫ0 is the permittivity of free space, ǫr is the relative
7
permittivity of the medium (assumed identical for the media both inside and outside the PE
8
layer), and e is the electronic charge. Also the above equation assumes that the electrolyte
9
ions are monovalent and the non-Poisson-Boltzmann effects (e.g., finite ion size effect, sol-
10
vent polarization effect, and ion-ion correlation effects) have been neglected. Please note
11
that here we are considering a pH-responsive ionization and charging of the PE brush tip
12
– accordingly, we have considered the contributions of the hydrogen and the hydroxyl ions
13
in the EDL free energy. Also, similar to our previous studies, 27,28 we assume that we add
14
a salt of concentration c∞ and an acid (furnishing same anions as the electrolyte salt) of
15
concentration cH + ,∞ . Under these conditions, n+,∞ = n∞ (where n∞ = 103 NA c∞ , with NA
16
being the Avogadro number) and n−,∞ = n∞ + nH + ,∞ (where nH + ,∞ = 103 NA cH + ,∞ ).
17
18
Under these circumstances, we can now express the overall free energy of PE-brush-surrounding-
19
electrolyte system by using eqs.(2,3,4,5,6) in eq.(1): ωNp2 σ 1 3kB T d2 1 F = + k T + (ψs σch,pH ) + B 2 2 Np ak d σ σ
8
Z
0
fEDL (ψ, ψ ′ , ni )dy. −h
ACS Paragon Plus Environment
(7)
Page 9 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
1
In order to obtain the equilibrium, the minimization of this resulting free energy F [see
2
eq.(7)] will be carried out with respect to the variables ψ, n± , nH + , nOH − , and d.
3
4
Minimization of F with respect to ψ yields: d2 ψ e (−n+ + n− − nH + + nOH − ) = . dy 2 ε0 εr
5
(8)
On the other hand, the minimization of F with respect to ni (i = ±, H + , OH − ) will yield zi eψ , ni = ni,∞ exp − kB T
(9)
6
where zi is the valence of the ionic species i.
7
Of course, eqs.(8, 9) are valid both inside and outside the PE brushes and employment of
8
eq.(9) in eq.(8) will yield the well-known Poisson-Boltzmann equation in terms of the EDL
9
potential ψ.
10
The necessary boundary conditions for solving this equation in ψ are:
dψ dy
= 0, y=−h
dψ dy
= 0, y=0
(ψ)(y=−h+d)− = (ψ)(y=−h+d)+ .
(10)
11
Finally, we shall require a fourth condition that will connect the gradients of electrostatic
12
potentials inside and outside the brush in terms of the PE end charge density σch,pH . This
13
condition is obtained by minimizing the overall free energy F with respect to ψs (see our
14
previous paper 27 for the detailed procedure):
dψ dy
y=(−h+d)+
σch,pH δF = 0 ⇒ ψs′ = − ⇒ δψs ε0 εr σch,pH dψ . − =− dy y=(−h+d)− ε0 εr
9
ACS Paragon Plus Environment
(11)
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 10 of 38
1
Solution of eqs.(8,9) in presence of conditions expressed by eqs.(10,11) will provide ψ and
2
ni . This, in turn, when employed in eqs.(5,6) will help us quantify the overall EDL energy.
3
Of course, this overall EDL energy is the equilibrium EDL energy that can be employed in
4
eq.(7) in order to obtain the total energy F . Subsequently, we shall minimize this F [see
5
eq.(7)] with respect to d and obtain the equilibrium value of the brush height d.
6
Calculation of the EOS Transport
7
The main purpose of this paper is to study the EOS transport triggered in presence of an
8
externally applied axial electric field (of magnitude E) in such pH-responsive, end-charged
9
(with charge density σch,pH ) PE-brush-grafted nanochannels [see Fig. 1(b)] and demonstrate
10
that this EOS transport is significantly stronger than the EOS transport ensued in a brush-
11
free nanochannel with a wall charge density of σch,pH [see Fig. 1(a)]. This EOS flow in
12
either of the systems (with and without the wall-grafted PE brushes) is triggered due to
13
the interaction of the applied electric field E and the imbalance of the ionic number density
14
within the EDL. Considering the EOS flow to be steady, hydrodynamically fully-developed,
15
and uni-directional, we can express the governing equation dictating the flow as (considering
16
the nanochannel bottom half): d2 u η + e (n+ − n− + nH + − nOH − ) E − u = 0 [for − h ≤ y ≤ −h + d] , 2 dy k 2 du [for − h + d ≤ y ≤ 0] , η 2 + e(n+ − n− + nH + − nOH − )E = 0 dy η
17
18
(12)
where u is the uni-directional velocity, η is the dynamic viscosity of the liquid, e is the elec 2 d 2 tronic charge, ni is the number density of the ionic species i, and k = ak σa3 Np φ is the k
σa3k Np φ d
is the volume fraction of the PE brush layer. For the present study,
19
permeability and
20
we consider a stepped profile of the end-charged PE brush – hence we have φ = 1.
21
10
ACS Paragon Plus Environment
Page 11 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
1
Using eq.(9) and expressing the bulk number densities of the ions in a manner identical
2
to that described after eq.(6), we can express eq.(12) in dimensionless form as E¯ d2 u¯ ¯ + (1 + n ¯ −n ¯ +n ¯ ] + ,∞ ) exp ψ + ,∞ exp −ψ − ,∞ exp ψ − [− exp − ψ ¯ ¯ ¯ H H OH ¯2 d¯ y 2 2λ 2 2 ak σNp φ ¯ , u ¯ = 0 for − 1 ≤ y ¯ ≤ −1 + d − d¯ E¯ d2 u¯ ¯ + (1 + n ¯ −n ¯ +n ¯ ] + ,∞ ) exp ψ + ,∞ exp −ψ − ,∞ exp ψ − [− exp − ψ ¯ ¯ ¯ H H OH 2 2 ¯ d¯ y 2λ for − 1 + d¯ ≤ y¯ ≤ 0 . (13)
3
4
where ψ¯ = eψ/(kB T ), u¯ = u/u0 (u0 is the velocity scale), E¯ = E/E0 (u0 and E0 are p ¯ = λ/h (λ = ǫ0 ǫr kB T /(2n∞ e2 ) ¯ i,∞ = ni,∞ /n∞ , y¯ = y/h, λ connected as u0 = kBeT ε0 εηr E0 ), n
5
is the EDL thickness), and d¯ = d/h.
6
With the knowledge of the dimensionless EDL electrostatic potential ψ¯ (solution procedure
7
of ψ has been discussed in the previous subsection), eq.(13) is finally solved numerically in
8
the presence of the following dimensionless boundary conditions:
d¯ u d¯ y
= 0, (¯ u)y¯=−1 = 0, y¯=0
(¯ u)y¯=(−1+d)− = (¯ u)y¯=(−1+d)+ ,
d¯ u d¯ y
= y¯=(−1+d)−
d¯ u d¯ y
.
(14)
y¯=(−1+d)+
9
It is worthwhile to note here that our model does not consider the nanochannel ion
10
concentration polarization (ICP) effect, which refers to the simultaneous depletion and ac-
11
cumulation (of both coions and counterions) at axially separated locations (typically at the
12
entry and at the exit) in a nanochannel. ICP effect invariably arises when there is an axial
13
jump in the ion concentration. Therefore, one witnesses such ICP at the junction of mi-
14
crochannel and a nanochannel (such a nanochannel may or may not be grafted with PE
15
brushes), 18,30–32 for translocation of a DNA through a nanochannel or a nanopore (since the
16
DNA adds its own EDL distribution in a charged nanochannel), 33 etc. On the other hand,
11
ACS Paragon Plus Environment
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1
the present study considers a parallel-plate nanochannel with uniformly grafted end-charged
2
polyelectrolyte (PE) brushes. Therefore, unlike the examples discussed above there is no pos-
3
sibility of any axial variation/jump in the ion concentration – accordingly, we have neglected
4
the ICP effect in our modeling. Of course, there is a possibility of such an ICP effect at
5
the junction of this end-charged PE-brush grafted nanochannel with a possible microchannel
6
reservoir; but we consider the nanochannel to be sufficiently long so that such nanochannel
7
end-effects (or equivalently the ICP generated at the nanochannel ends) can be neglected in
8
our calculations.
9
Results
10
Variation of the brush height
11
In our recent papers, 27,28 we have provided a detailed analysis of the variation of the height
12
of the nanoconfined, end-charged, pH-responsive PE brushes as a function of degree of con-
13
finement (or equivalently, short and tall brushes), pH and salt concentration. We do not
14
repeat those results here, but rather simply summarize the key issues that will be needed to
15
explain the subsequent results on the variation of the EDL electrostatics, ion concentration,
16
and the EOS transport.
17
A key parameter that dictates the brush height is the degree of confinement, quantified
18
by whether d0 < h/2 (weak confinement) or d0 > h/2 (strong confinement). Here d0 refers to
19
the height of the uncharged polymer brushes having identical expressions of the elastic and
20
excluded volume energies as the end-charged PE brushes. For brushes with d0 > h/2, the
21
electrostatic energy contributes to the lowering of the brush height d as compared to d0 , while
22
for brushes with d0 < h/2, the electrostatic energy ensures that d > d0 . The electrostatic
23
effects are maximum for pH = 7, for which the ionization of the end-charge-producing group
24
is maximum. Consequently, at pH = 7 there is a maximum difference between d and d0 –
25
this difference ensures that for a given salt concentration d has the largest (smallest) value 12
ACS Paragon Plus Environment
Page 12 of 38
Page 13 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
1
for pH = 7 for brushes with d0 < h/2 (d0 > h/2). For such large pH values, increase in salt
2
concentration increases (decreases) the impact of the electrostatic free energy (in altering
3
the brush height) for small (large) values of salt concentration. Accordingly, we witness that
4
d first decreases (increases), attains a minimum (maximum), and then increases (decreases)
5
with the salt concentration for brushes with h > d0 > h/2 (d0 < h/2). It is worthwhile
6
to mention here that the height d0 of the uncharged brushes can be increased by either
7
increasing the grafting density σ or the polymer size Np [since d0 ∼ Np (a5k σ)
8
that d0 ∼ σ 1/3 and d0 ∼ Np , one will require a much larger (smaller) increase in σ (Np ) in
9
order to ensure a given increase in the brush height. Of course, as will be explained later, the
10
EOS transport in such end-charged PE brush grafted nanochannels will be severely affected
11
depending on whether d0 increased by increasing σ or by increasing Np .
12
EDL electrostatic potential and the ion number density distribution
13
In Fig. 2, we study the transverse variation of the magnitude of the dimensionless EDL
14
¯ = |eψ/(kB T )|] (top panel) and the number densities of the counelectrostatic potential [|ψ|
15
terions (n+ ) (middle panel) and coions (n− ) (bottom panel). Significance of this figure is
16
that it provides a critical understanding about the electrostatics of the problem, which is
17
central to correctly interpret the EOS flow fields. We study all the quantities (ψ¯ and n± )
18
for pH = 7 for five different nanochannel systems: a) nanochannels grafted with short-loose
19
brushes (Np = 2000, ℓ = 80 nm, d0 = 34 nm), b) nanochannels grafted with short-loose,
20
but slightly taller brushes (Np = 2800, ℓ = 80 nm, d0 = 49 nm), c) nanochannels grafted
21
with short-dense brushes (Np = 846, ℓ = 22 nm, d0 = 34 nm), d) nanochannels grafted with
22
tall-dense brushes (Np = 2000, ℓ = 22 nm, d0 = 82 nm), and (e) nanochannels grafted with
23
no brush. This variation of the configuration of the grafted brushes (or the complete absence
24
of the brushes) dictates the specific location of the EDL within the nanochannel. As will be
25
discussed later, this location of the EDL along with the EDL thickness (or equivalently, bulk
26
ionic concentration) play vital roles in dictating the overall EOS transport. For example, for 13
ACS Paragon Plus Environment
1/3
]. 27 Given
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Figure 2: Variation of the magnitude of the dimensionless transverse EDL electrostatic ¯ (top panel), transverse counterion number density n+ (middle pannel), and potential |ψ| transverse coion number density n− (bottom pannel) as functions of the bulk salt concentrations for pH=7. Results are shown for a) nanochannels grafted with short-loose brushes (Np = 2000, ℓ = 80 nm, d0 = 34 nm), b) nanochannels grafted with short-loose, but slightly taller brushes (Np = 2800, ℓ = 80 nm, d0 = 49 nm), c) nanochannels grafted with shortdense brushes Np = 846, ℓ = 22 nm, d0 = 34 nm, d) nanochannels grafted with tall-dense brushes Np = 2000, ℓ = 22 nm, d0 = 82 nm, and (e) nanochannels grafted with no brush. Other parameters are σch = −0.0008 C/m2 (this is the charge density of the end charges of the brushes for nanochannels grafted with brushes; this is also the charge density of bare walls of nanochannels without the brushes), pKa = 4, h = 100 nm, χ = 0.4, ak = 1 nm, kB = 1.38 × 10−23 J/K, T = 300 K, e = 1.6 × 10−19 C, ǫ0 = 8.8 × 10−12 F/m, ǫr = 79.8.
1
the PE-brush-free nanochannel [see Fig. 2(e)], the EDL is obviously confined at the wall,
2
whereas for the nanochannels grafted with the PE-brushes [see Fig. 2(a-d)], the EDLs are lo-
3
cated at the brush tip. This can be understood by noting the location of the maximum value
4
¯ for all of these five cases. Variation in the salt concentration has profound influence of |ψ|
5
¯ for all the five cases. Smaller salt concentration on the magnitude and the distribution of |ψ|
6
¯ is implies a larger EDL thickness. As a consequence, the extent of the spatial decay of |ψ|
7
¯ even at locations further away from weak ensuring that there is a distinctly finite value of |ψ| 14
ACS Paragon Plus Environment
Page 14 of 38
Page 15 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
1
¯ is highest. Consequently for weak salt concentration, one witnesses the locations where |ψ|
2
¯ at locations far away from the wall for the PE-brush-free nanochannels, as well as finite |ψ|
3
far away on either sides of the charged end of the PE brush for nanochannels grafted with
4
¯ ensures a loend-charged PE brushes. This specific salt-concentration-driven variation of |ψ|
5
calization of the maximum charge density and maximum EOS body force at the brush tip for
6
large salt concentration, whereas a dispersion (and hence non-localization) of the body force
7
away from the brush tip for small salt concentration. As will be illustrated subsequently,
8
such force localization for large salt concentration is key to attributing ascertaining EOS
9
¯ increases in magnitude for velocity for nanochannels with end-charged brushes. Finally, |ψ|
10
smaller salt concentration. It can be easily explained by noting that |ψ| ∼ σch,pH λ (where
11
λ is the EDL thickness), thereby justifying enhanced |ψ| for weaker salt concentration (i.e.,
12
enhanced λ).
13
¯ distribuNumber density distributions of the ions (n± ) are commensurate with this |ψ|
14
tion. Consequently, we witness (a) largest (smallest) values of the counterion (coion) number
15
densities at the wall (for PE-brush-free nanochannels) and at the location of the end charge
16
(for end charged PE brush grafted nanochannels) and (b) the ion concentrations demonstrat-
17
ing weakest (strongest) decays for smallest (largest) bulk electrolyte salt concentrations.
18
Electroosmotic velocity field
19
In Fig. 3, we show the transverse variation of the EOS velocity field for different salt
20
concentrations at pH = 7 for these five different nanochannel systems. This is the central
21
result of this paper. The key features of these EOS flow fields are as follow. Firstly, for
22
brush-free nanochannels [see Fig. 3(e)], the least magnitude of the EOS flow strength as
23
well as the flattest EOS velocity profile (or the profile that has closest resemblance to the
24
classical “plug”-shaped EOS flow profile) is witnessed for the largest salt concentration.
25
Also for this case, a decrease in the salt concentration leads to a progressive increase in the
26
magnitude of the EOS flow strength and a progressive decrease in the “plug”-like nature 15
ACS Paragon Plus Environment
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Figure 3: Variation of the transverse electroosmotic velocities as functions of the bulk salt concentrations for pH=7. Results are shown for a) nanochannels grafted with short-loose brushes (Np = 2000, ℓ = 80 nm, d0 = 34 nm), b) nanochannels grafted with short-loose, but slightly taller brushes (Np = 2800, ℓ = 80 nm, d0 = 49 nm), c) nanochannels grafted with short-dense brushes (Np = 846, ℓ = 22 nm, d0 = 34 nm), d) nanochannels grafted with tall-dense brushes (Np = 2000, ℓ = 22 nm, d0 = 82 nm), and (e) nanochannels grafted with no brush. We represent the loose brushes as light green [see (a) and (b)] and dense brushes as pink [see (c) and (d)]. Other parameters for all the figures are identical to that in Fig. 2.
1
of the flow field. It is trivial to infer that the corresponding variation in ψ [see Fig. 2(e),
2
top panel], demonstrating the weakest value and the steepest variation for this largest salt
3
concentration, is responsible for this velocity profile. For nanochannels with short-loose
4
brushes (by “loose” we imply less dense) [see Fig. 3(a), for which Np = 2000, ℓ = 80 nm,
5
d0 = 34 nm], we witness, most remarkably, a significantly larger velocity (as compared to
6
the brush-free nanochannels) for large salt concentration. Additionally, we witness that the
7
decrease in the salt concentration first decreases and then increases the strength of the EOS
8
transport particularly in the vicinity of the nanochannel centreline. Further, a decrease
9
in the salt concentration (or equivalently, an increase in the EDL thickness) enforces the
10
velocity profile to suffer a large deviation from its “classical” plug shape. Obviously, the
11
most surprising of all the results is this remarkable enhancement (in particular, for large salt
12
concentration) in the EOS flow strength for nanochannels grafted with the PE brushes, as
13
compared to the EOS flow in brush-free nanochannels. This is completely contrary to the
14
classical understanding that the presence of the brushes lining the nanochannel walls will
15
invariably lower the flow speed on account of PE-induced enhanced drag. 12,13 For the end
16
charged brushes, the EDL is localized at the brush tip that is substantially away from the 16
ACS Paragon Plus Environment
Page 16 of 38
Page 17 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
1
wall. For larger salt concentration, the EDL thickness being very small, this localization is
2
so strong that the EDL ceases to exist well before the wall. The driving force for the EOS
3
transport comes from the difference between the counterions (n+ ) and coion (n− ) number
4
densities – this difference is maximum within the EDL. Therefore for end-charged brushes,
5
in presence of large bulk salt concentration (i.e., small EDL), this driving force is primarily
6
localized at the location substantially away from wall. As a consequence, the liquid is
7
subjected to a maximum localized body force at a location where the wall induced retarding
8
shear stress is very minimal. This, in turn, ensures a significantly large influence of the
9
EOS body force, enforcing a large EOS velocity. Therefore, we can infer that this most
10
remarkable scenario where the presence of the end-charged PE brushes enhances the EOS
11
flow strength is triggered by the localization of the EDL and the corresponding localization
12
of the body force at a distance far away from the wall. It is clear from the above discussions
13
that the key to the development of this augmented EOS transport is the preferential location
14
of the maximum EOS body force away from the wall. This is quantified in Fig. 4, where
15
the electroosmotic body force (quantified by those f¯, corresponding to which f¯ > 0) and
16
the drag force (quantified by those f¯, corresponding to which f¯ < 0) for each of the five
17
different nanochannel systems and for different salt concentrations are elucidated. One can
18
straightaway compare the case of no brush [see Fig. 4(e)] and the case of short brushes
19
[see Fig. 4(a)] – the results establish that the localization of the maximum EOS body
20
force is substantially away from the wall for the nanochannel with brushes as compared
21
to the nanochannel without the brushes. Also, it is trivial to identify from Fig. 4 that
22
the maximum value of the EOS body force occurs for large salt concentration for both
23
nanochannels with and without the brushes. Of course, for small salt concentrations the
24
EDL thickness becomes large – as a consequence, the EOS body force is no longer localized
25
and get dispersed ensuring that a part of the EOS body force is also present near the wall
26
(as the EDLs extend away from the brush tip). Therefore, for such a salt concentration
27
the impact of the localization of the EOS body force at the brush tip gets severely reduced,
17
ACS Paragon Plus Environment
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1
ensuring minimal (if any) enhancement of the EOS flow speed in brush-grafted nanochannels
2
as compared to the brush-free nanochannels.
Figure 4: Variation of the dimensionless per unit volume forces (f¯) in the transverse direction as functions of the bulk salt concentrations for pH=7. Here f¯ > 0 represents the dimensionless per unit volume EOS body force, while f¯ < 0 represents the retarding PEbrush-layer-induced per unit volume drag force. Results are shown for a) nanochannels grafted with short-loose brushes (Np = 2000, ℓ = 80 nm, d0 = 34 nm), b) nanochannels grafted with short-loose, but slightly taller brushes (Np = 2800, ℓ = 80 nm, d0 = 49 nm), c) nanochannels grafted with short-dense brushes (Np = 846, ℓ = 22 nm, d0 = 34 nm), d) nanochannels grafted with tall-dense brushes (Np = 2000, ℓ = 22 nm, d0 = 82 nm), and (e) nanochannels grafted with no brush. Other parameters are identical to those in Fig. 2.
3
A very important question in this context is: For a given E and σch , does the EOS
4
transport depend solely on the value of the brush height or on the parameters that dictate the
5
brush height? In order to resolve this issue, we probe the EOS transport for the nanochannel
6
system grafted with end-charged PE brushes of same d0 as that of Fig 3(a) (i.e., d0 = 34nm)
7
but having a larger grafting density (ℓ = 22 nm) and a smaller Np (Np = 846) (i.e., we study
8
the case of nanochannels grafted with short and dense brushes) [see Fig. 3(c)]. Here, we
9
clearly see that the velocity for the case with larger σ is distinctly smaller (particularly for a
10
large salt concentration), on account of the larger drag force (since drag coefficient ∼ σ 2/3 ).
11
This becomes plainly evident from the comparison of the drag forces (represented by those
12
f¯ values for which f¯ < 0) for these two cases [please see Figs. 4(a) and 4(c)].
13
Finally, we are interested to probe the effect of the brush height in the augmentation of
14
the EOS flow strength. For that purpose, we probe the EOS flow behavior for the brushes
15
with heights greater than d0 = 34 nm. We consider a taller brush (as compared to one 18
ACS Paragon Plus Environment
Page 18 of 38
Page 19 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
1
where d0 = 34 nm) with a large σ (Np = 2000, ℓ = 22 nm, d0 = 84 nm) [see Fig. 3(d)
2
for the corresponding EOS flow profile] and another taller brush (as compared to one where
3
d0 = 34 nm) with a small σ (Np = 2800, ℓ = 80 nm, d0 = 49 nm) [see Fig. 3(b) for the
4
corresponding EOS flow profile]. For the taller brush with large σ, the influence of larger σ
5
in augmenting the drag overwhelms the effect associated with the localization of the EOS
6
body force at the brush tip, resulting in a much smaller velocity (particularly at large salt
7
concentration) [please compare the EOS flow profiles of Figs.3(a) and (d)]. Such profound
8
influence of the drag force for taller and more dense brushes can be confirmed by noting
9
the significantly large drag force in Fig. 4(d). On the other hand, for taller but less dense
10
brushes [the corresponding EOS flow profile is shown in Fig. 3(b)], it is the localization
11
of the EDL at the brush tip that governs the flow, leading to an EOS flow strength that
12
is more (particularly at large salt concentration) than that for nanochannels grafted with
13
shorter and less dense brushes [the corresponding EOS flow profile is shown in Fig. 3(a)].
14
Of course, this issue gets substantiated when the corresponding forces are compared [i.e.,
15
compare the forces shown in Fig. 4(a) and (b)] – the drag force is similar for both these
16
cases, but the maximum of the EOS body is located at a greater distance from the wall for
17
the taller brush.
18
For all the five nanochannel systems studied here, the smallness of the EDL thickness for
19
large salt concentrations will ensure that the velocity profile remains very flat (or “plug”-
20
shaped) outside the brush, while a larger EDL (or equivalently, a larger spatial distribution
21
of the charge density gradient) for smaller salt concentration ensures a velocity profile far
22
deviated from the “plug”-shaped profiles.
23
pH-responsive electrostatics and EOS velocity fields
24
¯ u¯, f¯, In Figs. 5,6,7,8, we show the effect of the variation of pH and salt concentration on |ψ|,
25
n+ ,n− , and nH + for the four different kinds of PE-grafted nanochannel systems. For small
26
pH, the concentration of H + ions in the electrolyte solution is so high that the ionization of 19
ACS Paragon Plus Environment
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
¯ (magnitude of dimensionless electrostatic potential), u¯ Figure 5: Transverse variation of |ψ| (dimensionless EOS velocity), f¯ (f¯ > 0 represents the dimensionless per unit volume EOS body force, while f¯ < 0 represents the retarding PE-brush-layer-induced per unit volume drag force), n+ (counterion number density), n− (coion number density), and nH + (number density of hydrogen ions). Results are shown for nanochannels grafted with short-loose brushes (Np = 2000, ℓ = 80 nm, d0 = 34 nm) for (a) pH=3, (b) pH=4, and (c) pH=5. Other parameters are identical to those in Fig. 2.
20
ACS Paragon Plus Environment
Page 20 of 38
Page 21 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
¯ (magnitude of dimensionless electrostatic potential), u¯ Figure 6: Transverse variation of |ψ| (dimensionless EOS velocity), f¯ (f¯ > 0 represents the dimensionless per unit volume EOS body force, while f¯ < 0 represents the retarding PE-brush-layer-induced per unit volume drag force), n+ (counterion number density), n− (coion number density), and nH + (number density of hydrogen ions). Results are shown for nanochannels grafted with short-loose, but slightly taller brushes (Np = 2800, ℓ = 80 nm, d0 = 49 nm) for (a) pH=3, (b) pH=4, and (c) pH=5. Other parameters are identical to those in Fig. 2.
21
ACS Paragon Plus Environment
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
¯ (magnitude of dimensionless electrostatic potential), u¯ Figure 7: Transverse variation of |ψ| (dimensionless EOS velocity), f¯ (f¯ > 0 represents the dimensionless per unit volume EOS body force, while f¯ < 0 represents the retarding PE-brush-layer-induced per unit volume drag force), n+ (counterion number density), n− (coion number density), and nH + (number density of hydrogen ions). Results are shown for nanochannels grafted with short-dense brushes (Np = 846, ℓ = 22 nm, d0 = 34 nm) for (a) pH=3, (b) pH=4, and (c) pH=5. Other parameters are identical to those in Fig. 2.
22
ACS Paragon Plus Environment
Page 22 of 38
Page 23 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
¯ (magnitude of dimensionless electrostatic potential), Figure 8: Transverse variation of |ψ| u¯ (dimensionless EOS velocity), f¯ (f¯ > 0 represents the dimensionless per unit volume EOS body force, while f¯ < 0 represents the retarding PE-brush-layer-induced per unit volume drag force), n+ (counterion number density), n− (coion number density), and nH + (number density of hydrogen ions). Results are shown for nanochannels grafted with talldense brushes (Np = 2000, ℓ = 22 nm, d0 = 82 nm) for (a) pH=3, (b) pH=4, and (c) pH=5. Other parameters are identical to those in Fig. 2.
23
ACS Paragon Plus Environment
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1
the end-charge-producing group (this ionization produces the H + ions) is severely retarded.
2
Accordingly, the magnitude of the end-charge is substantially lowered. This is reflected in
3
¯ and |¯ the substantially reduced value of |ψ| u| for cases with small pH (pH = 3, 4) for all the
4
four different PE-brush-grafted nanochannel systems. On the other hand, for nanochannels
5
grafted with both short and tall as well as loose and dense brushes, only for pH ≥ 5 we
6
¯ and u¯ that have been witness the salt concentration dependent qualitative variation in |ψ|
7
described in Figs. 2 and 3.
Figure 9: Phase space for iso-volume-flow-rate. The lines with numbers denote the ℓ − Np combinations that ensure identical flow rates with the numbers on the lines denoting the dimensionless flow rate, defined in eq.(15). The shaded region shows the ℓ−Np combinations that ensure that the grafted PE molecules form brushes whose heights are less than the nanochannel half height. Below this shaded zone the brushes are taller than the nanochannel half height, while above the shaded zone the grafting is so weak that the grafted polymer molecules no longer form the brushes.Results here are shown for c∞ = 10−2 M , σch = −8 × 10−4 C/m2 , and pH = 7.
24
ACS Paragon Plus Environment
Page 24 of 38
Page 25 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
1
Phase space for the volume flow rate ratio in nanochannels grafted
2
with end-charged PE brushes
3
The interplay of the grafting density and the monomer size in dictating the strength of the
4
overall EOS transport in nanochannels grafted with the end-charge brushes is summarized
5
in the iso-volume-flow rate (or iso-Q) phase-space plot shown in Fig. 9. This phase space
6
is provided for large salt concentration (c∞ = 10−2 M ) and large pH (pH = 7) (i.e., the
7
conditions corresponding to which the EOS transport in PE-brush-grafted nanochannels is
8
most augmented). In this figure, the lines with numbers denote the ℓ − Np combinations
9
that ensure identical dimensionless volume flow rate ratios, expressed as: R1
u¯ d¯ y ¯ = R −1 B , Q 1 u¯ d¯ y −1 N B
(15)
10
where u¯B and u¯N B are the dimensionless EOS velocity profiles in nanochannels with and
11
without the brushes, respectively. Of course, in Fig. 9, we also show (see the shaded region)
12
the ℓ − Np combination that ensure that the grafted polymer molecules form brushes that
13
have height less than the nanochannel half height (so that there is no interpenetration of the
14
brushes grafted on the two opposing walls of the nanochannel). Therefore, basically we focus
15
on the iso-Q lines that are within this shaded zone. The first and the most important finding
16
is the massive increase in the volume flow rate for the nanochannels with brushes, evident
17
by the large magnitudes of the volume flow rate ratios [see Fig. 9 and eq.(15). As discussed
18
previously, combination of ℓ and Np dictate the brush height as well as the drag force and
19
the interplay of these two factors eventually decide EOS flow profile. This flow profile along
20
with the space available for the flow (i.e., the transverse section of the nanochannel not
21
occupied by the brushes) dictate the consequent volume flow rate. For very small ℓ/ak (or
22
equivalently for a very large grafting density) at a given Np (Np ≥ 2000) the brush height
23
is very large so that the major part of the nanochannel is blocked by the brush, causing a
24
relatively small volume flow rate. Of course, for such a large grafting density, the brush25
ACS Paragon Plus Environment
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1
induced drag force is also substantially high, which contributes to ensure a very small flow
2
rate. On a subsequent increase of ℓ/ak (or equivalently, a decrease in the grafting density)
3
three things happen: first a slit-like gap opens due to the reduction of the brush height,
4
second the brush-induced drag reduces, and third the effect of the localization of the EOS
5
body force (on account of the localization of the EDL at the brush end, particularly for
6
large salt concentration as has been studied in Fig. 9) away from the wall starts becoming
7
important. All these three factors contribute to enhancing the flow rate. How these three
8
factors pan out and how they interplay to influence the final flow rate with a further increase
9
of ℓ/ak decides the above iso-Q phase diagram. A further increase in ℓ/ak leads to a greater
10
gap opening and a lesser effect of the localization of the EOS body force away from the
11
wall (both caused by a reduction in the brush height) and a further weakening of the drag
12
force – the consequence is a further increase in the flow rate. Here the central factor is this
13
localization of the body force away from the wall – while an increase in ℓ/ak and a consequent
14
lowering of the brush height makes this localization closer to the wall, its influence coupled
15
with an augmented flow-passage area and a substantially reduced (or even non-existent)
16
brush-induced drag ensures this augmented flow rate. However, beyond a certain value of
17
ℓ/ak , the brush height becomes so small that this localization effect is virtually non-existent
18
and this, in turn, ensures a net reduction in the flow rate. In this way, we can explain why
19
the flow rate first increases and then decreases with an increase in ℓ/ak for a given Np .
20
Discussions
21
Impact of the choice of the monomer profile
22
Quantification of the monomer distribution along the brush length is critical for quantifying
23
the drag coefficient used in the modelling of the EOS transport. In the present study, we have
24
considered a uniform monomer profile (or equivalently, a stepped monomer profile where φ =
25
1) as proposed by Alexander 24 and de Gennes 25,26 and subsequently used in a large number 26
ACS Paragon Plus Environment
Page 26 of 38
Page 27 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
1
of studies on electrokinetic transport in PE-grafted nanochannels. 12,19,21,23 Of course, a more
2
complete model would have necessitated a more appropriate form of the monomer profile that
3
is self-consistent with the presence of PE electrostatic contribution due to the presence of the
4
charge only at the PE tip. Mishra et al. 34 and Zhulina and Borisov 35 respectively proposed
5
a parabolic and an exponentially decaying monomer distribution for the case where the PE
6
brushes contained charges along its entire backbone. However, for the present case where the
7
PE electrostatics is due to the presence of only PE end charge, monomer distribution remains
8
unknown. While developing this present model on EOS transport by first estimating the
9
appropriate monomer distribution for the end-charged PE brushes is indeed a possibility, we
10
refrain from doing that and provide our results for the simplistic case of uniform monomer
11
profile. The reason is that we believe that the consideration of a non-uniform, decaying
12
(along the brush height) monomer profile, if at all, will only strengthen the central message
13
of the present paper, which is the enhancement of the EOS flow by end-charged PE brushes.
14
This stems from the fact that for such a monomer distribution, the monomer density will
15
be least near the brush tip and accordingly the PE-induced drag force will be much smaller
16
(as compared to the case of φ = 1) near the brush tip. Consequently, the retardation to the
17
flow near the PE-tip (i.e., where the EOS body force is localized) due to the wall shear and
18
the PE drag will reduce even further, thereby ensuring an even further augmentation of the
19
EOS transport.
20
Choice of the parameters
21
The present study involves various physiochemical parameters. All of them have been mo-
22
tivated by realistic examples of polyelectrolyte and nanochannel systems as illustrated below:
23
24
Choice of pKa :
25
We consider pKa = 4. This is motivated by the fact that we consider the end-charged group
26
to be similar to a pH-responsive acrylic acid group that has a pKa value of 4.26. 36 27
ACS Paragon Plus Environment
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1
2
Choice of ℓ:
3
Here ℓ defines the grafting density σ, i.e., σ ∼ 1/ℓ2 . We have used ℓ = 22 nm, 80 nm. This
4
implies a grafting density range of σ = 10−4 − 102 nm−2 . While σ = 10−4 nm−2 is a slightly
5
weak value of the grafting density, σ values in the order of 10−2 nm−2 and 10−3 nm−2 has
6
been routinely reported in the experiments involving polymer brushes. 37,38
7
8
Choice of Np :
9
Np is the number of monomers in a given PE brush chain. In the present study, we con-
10
sider two values of Np : 2000, 2800. These numbers lie within the typical average values
11
of the number of monomers in a polymer brush molecule experimentally studied. Exam-
12
ples include studies that have considered polymer brushes with very similar, 40 or larger, 40,41
13
or smaller 40–42 number of monomers per polymer chain (for these experimental studies 40–42
14
number of monomers Np are calculated as the ratio of the total molecular weight of the
15
polymer chain to the molecular weight of the monomer).
16
17
Choice of d0 :
18
d0 is the height of the brushes without the electrostatic effects. Our calculations consider a
19
relatively wide range of d0 values ranging from 34 nm to 82 nm, resulted by selection of ℓ and
20
Np . There are several experimental evidences of similar values of d0 – e.g., d0 = 30 nm, 38
21
d0 = 20 nm − 116 nm. 39
22
23
Choice of h:
24
Here we have consider the nanochannel half height h = 100 nm.
25
Such nanochannel/nanocapillary/nanocone dimensions have been routinely witnessed for ex-
26
perimental studies involving nanochannels/nanocpillaries/nanocones grafted with polymer
27
or polyelectrolyte brushes. 8,43–48
28
ACS Paragon Plus Environment
Page 28 of 38
Page 29 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
1
Conclusions
2
In this study, we describe the most remarkable EOS flow enhancement in nanochannels
3
grafted with the end-charged PE brushes, completely contrary to the findings of the existing
4
studies demonstrating substantial EOS flow reduction in PE-grafted nanochannels. 12–14 Of
5
course, the critical difference between these previous studies and the present study is that
6
for all these previous studies the PE brush is charged along its entire backbone, while in
7
the present case the PE molecule contains charge only at its non-grafted end located far
8
away from the grafting surface. As a consequence, for the end-charged brushes, the EDL
9
and the EDL-induced maximum body force for driving the EOS-flow is localized at the
10
charged end of the brush (i.e., far away from the wall), ensuring that the resulting flow
11
is subjected to very weak wall-induced retarding shear force enabling a very large EOS
12
transport. We witness a much larger EOS flow strength as compared to nanochannels without
13
the PE brushes; however, an increase in the brush height enhances the EOS flow strength
14
progressively only when the parameters that dictate the increase in the brush height does
15
not additionally increase the drag coefficient. We believe that the present study, which is
16
based on a mean-field-based model that neglects the possible ICP effect, proposes a hitherto
17
unknown mechanism by which the EOS transport gets augmented in the PE-brush-grafted
18
nanochannels – we anticipate that this finding will open up new avenues for manipulating
19
the nanofluidic transport using nano-functionalized interfaces.
20
Appendix: Derivation of the expression of σch,pH
21
We consider a pH-responsive, negatively charged end-charged PE brush. Consequently, the
22
brush attains the charge by ionization of a weakly acidic group HA, which ionizes as: HA ⇌ H + + A− (ionization constant Ka ),
29
ACS Paragon Plus Environment
(16)
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1
Page 30 of 38
so that Ka =
cH + cA − . cHA
(17)
2
Here ci (i = HA, A− , H + ) is the concentrations in moles/litre at the location of the end
3
charge (i.e., y = ye ) and Ka is the ionization constant in moles per litre. Consequently, Ka′ =
nH + nA− , nHA
(18)
4
i.e., the concentrations are expressed as number densities (having units of 1/m3 ) and Ka′ =
5
NA 103 Ka has a unit of 1/m3 (NA is the Avogadro number).
6
Following the large volumes of literature relating the charge density (σch ) of an ionizable
7
surface to the concentration of species in the reaction that produces this surface charging, 49–51
8
we can express −eΓ0 = −e (ΓHA + ΓA− ) = σch ,
9
(19)
where Γ0 is the total surface site density of the end charges, and ΓHA and ΓA− are the
10
corresponding values associated with HA and A− (see Behrens and Grier 49 for details).
11
For the present case, we are interested to obtain the pH-dependent charge density – therefore
12
we would need σA− , i.e., σch,pH = −eΓA−
(20)
13
Of course, following Behrens and Grier 49 [kindly see eq.(4) in Behrens and Grier and note that
14
the condition expressed in eq.(21) below allows one to obtain eq.(4) in Behrens and Grier]
15
the site density corresponding to the individual species can be related to their corresponding
16
concentrations (or number densities) as: nHA ΓHA = Γ A− nA−
30
ACS Paragon Plus Environment
(21)
Page 31 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1
The Journal of Physical Chemistry
Using eq.(21), we can reduce eq.(18) to:
Ka′ =
nH + Γ A− , ΓHA
(22)
2
which is identical to eq.(4) in Behrens and Grier. Therefore, using eq.(19,20,22), we can
3
obtain: σch,pH = σch
Ka′ , nH + + Ka′
(23)
4
where nH + is the hydrogen ion number density at the location of the end charge, i.e., nH + =
5
nH + (ye ).
6
Acknowledgement
7
The authors gratefully acknowledge the Teaching Assistantship Program of The Department
8
of Mechanical Engineering, University of Maryland for providing financial support to Guang
9
Chen when she conducted this research. There was no external funding supporting this
10
work.
11
References
12
13
14
15
16
17
(1) Netz, R. R.; Andelman, D. Neutral and Charged Polymers at Interfaces. Phys. Rep. 2003, 380, 1–95. (2) Ballauff, M.; Borisov, O. Polyelectrolyte Brushes. Curr. Opin. Colloid Interface Sci. 2006, 11, 316–323. (3) Das, S.; Banik, M; Chen, G.; Sinha, S.; Mukherjee, R. Polyelectrolyte Brushes: Theory, Modelling, Synthesis and Applications. Soft Matt. 2015, 11, 8550–8583.
18
(4) Ali, M.; Yameen, B.; Neumann, R.; Ensinger, W.; Knoll, W.; Azzaroni, O. Biosensing
19
and Supramolecular Bioconjugation in Single Conical Polymer Nanochannels. Facile 31
ACS Paragon Plus Environment
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1
Incorporation of Biorecognition Elements into Nanoconfined Geometries. J. Am. Chem.
2
Soc. 2008, 130, 16351–16357.
3
4
(5) Ali, M.; Schiedt, B.; Neumann, R.; Ensinger, W. Biosensing with Functionalized Single Asymmetric Polymer Nanochannels. Macromol. Biosci. 2010, 10, 28–32.
5
(6) Umehara, S.; Karhanek, M.; Davis, R. W.; Pourmand, N. Label-free Biosensing with
6
Functionalized Nanopipette Probes. Proc. Natl. Acad. Sci. USA 2010, 106, 4611–4616.
7
(7) Ali, M.; Yameen, B.; Cervera, J.; Ramirez, P.; Neumann, R.; Ensinger, W.; Knoll, W.;
8
Azzaroni, O. Layer-by-layer Assembly of Polyelectrolytes into Ionic Current Rectifying
9
Solid-state Nanopores: Insights from Theory and Experiment. J. Am. Chem. Soc. 2010,
10
132, 8338–8348.
11
(8) Yameen, B.; Ali, M.; Neumann, R.; Ensinger, W.; Knoll, W.; Azzaroni, O. Single
12
Conical Nanopores Displaying pH-Tunable Rectifying Characteristics. Manipulating
13
Ionic Transport with Zwitterionic Polymer Brushes. J. Am. Chem. Soc. 2009, 131,
14
2070–2071.
15
(9) Ali, M.; Ramirez, P.; Mafe, S.; Neumann, R.; Ensinger, W. A pH-tunable Nanofluidic
16
Diode with a Broad Range of Rectifying Properties. ACS Nano 2009, 3, 603–608.
17
(10) Vilozny, B.; Wollenberg, A. L.; Actis, P.; Hwang, D.; Singaram, B.; Pourmand,
18
N. Carbohydrate-actuated Nanofluidic Diode: Switchable Current Rectification in a
19
Nanopipette. Nanoscale 2013, 5, 9214–9221.
20
21
(11) Adiga, S.; Brenner, D. W. Stimuli-responsive Polymer Brushes for Flow Control Through Nanopores. J. Funct. Biomater. 2012, 3, 239–256.
22
(12) Chanda, S.; Sinha, S.; Das, S. Streaming Potential and Electroviscous Effects in Soft
23
Nanochannels: Towards Designing More Efficient Nanofluidic Electrochemomechanical
24
Energy Converters. Soft Matt. 2014, 10, 7558–7568. 32
ACS Paragon Plus Environment
Page 32 of 38
Page 33 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1
2
3
4
The Journal of Physical Chemistry
(13) Chen, G.; Das, S. Electroosmotic Transport in Polyelectrolyte-Grafted Nanochannels with pH-dependent Charge Density. J. Appl. Phys. 2015, 117, 185304(1–9). (14) Zuo, Y.; Wang, G.; Yu, Y.; Zuo, C.; Liu, C.; Hu, D.; Wang, Y. Suppression of Electroosmotic Flow by Polyampholyte Brush. Microfluid. Nanofluid. 2014, 17, 923–931.
5
(15) R¨ uhs, P. A.; Adamcik, J.; Bolisetty, S.; Sanchez-Ferrera, A.; Mezzenga, R. A
6
Supramolecular Bottle-Brush Approach to Disassemble Amyloid Fibrils. Soft Matt.
7
2011, 7, 3571–3579.
8
(16) Hsu, H.; Sen, S.; Pearson, R. M.; Uddin, S.; Kral, P.; Hong, S. Poly(ethylene glycol)
9
Corona Chain Length Controls End-Group-Dependent Cell Interactions of Dendron
10
11
12
Micelles. Macromolecules 2014, 47, 6711–6718. (17) Mura, S.; Nicolas, J.; Couvreur, P. Stimuli-Responsive Nanocarriers for Drug Delivery. Nature Mater. 2013, 12, 991–1003.
13
(18) Yeh, L-H.; Zhang, M.; Hu, N.; Joo, S. W.; Qian, S.; Hsu, J-P. Electrokinetic Ion and
14
Fluid Transport in Nanopores Functionalized by Polyelectrolyte Brushes. Nanoscale
15
2012, 4, 5169–5177.
16
17
(19) Chen, G.; Das, S. Streaming Potential and Electroviscous Effects in Soft Nanochannels Beyond Debye-H¨ uckel Linearization. J. Colloid Interface Sci. 2015, 445, 357–363.
18
(20) Patwary, J.; Chen, G.; Das, S. Efficient Electrochemomechanical Energy Conversion in
19
Nanochannels Grafted with Polyelectrolyte Layers with pH-Dependent Charge Density.
20
Microfluid. Nanofluid. 2016, 20, 37.
21
(21) Poddar, A.; Maity, D.; Bandopadhyay, A.; Chakraborty, S. Electrokinetics in Polyelec-
22
trolyte Grafted Nanofluidic Channels Modulated by the Ion Partitioning Effect. Soft
23
Matt. 2016, 12, 5968–5978.
33
ACS Paragon Plus Environment
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1
(22) Benson, L.; Yeh, L-H.; Chou, T-H.; Qian, S. Field Effect Regulation of Donnan Poten-
2
tial and Electrokinetic Flow in a Functionalized Soft Nanochannel. Soft Matt. 2013, 9,
3
9767–9773.
4
(23) Milne, Z.; Yeh, L-H.; Chou, T-H.; Qian, S. Tunable Donnan Potential and Electroki-
5
netic Flow in a Biomimetic Gated Nanochannel with pH-Regulated Polyelectrolyte
6
Brushes. J. Phys. Chem. C 2014, 118, 19806–19813.
7
8
9
10
11
12
(24) Alexander, S. Polymer Adsorption on Small Spheres. A Scaling Approach. J. Phys. (Paris) 1977, 38, 977–981. (25) de Gennes, P. G. Scaling Theory of Polymer Adsorption. J. Phys. (Paris) 1976, 37, 1445–1452. (26) de Gennes, P. G. Conformations of Polymers Attached to an Interface. Macromolecules 1980, 13, 1069–1075.
13
(27) Chen, G.; Das, S. Anomalous Shrinking-Swelling of Nanoconfined End-Charged Poly-
14
electrolyte Brushes: Interplay of Confinement and Electrostatic Effects. J. Phys. Chem.
15
B 2016, 120, 6848–6857.
16
(28) Chen, G.; Das, S. Thermodynamics, Electrostatics, and Ionic Current in Nanochan-
17
nels Grafted with pH-Responsive End-Charged Polyelectrolyte Brushes. Electrophoresis
18
2016, 38, 720–729.
19
20
(29) Tsori, Y.; Andelman, D.; Joanny, J-F. Interfacial Instability of Charged-End-Group Polymer Brushes. Euro. Phys. Lett. 2008, 82, 46001.
21
(30) Zangle, T. A.; Mani, A.; Santiago, J. G. Theory and Experiments of Concentration
22
Polarization and Ion Focusing at Microchannel and Nanochannel Interfaces. Chem.
23
Soc. Rev. 2010, 39, 1014–1035.
34
ACS Paragon Plus Environment
Page 34 of 38
Page 35 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
1
(31) Kim, S. J.; Wang, Y-C.; Lee, J. H.; Jang, H.; Han, J. Concentration Polarization and
2
Nonlinear Electrokinetic Flow near a Nanofluidic Channel. Phys. Rev. Lett. 2007, 99,
3
044501.
4
5
(32) Yeh, L-H.; Zhang, M.; Qian, S.; Hsu, J-P.; Tseng, S. Ion Concentration Polarization in Polyelectrolyte-Modified Nanopores. J. Phys. Chem. C 2012, 116, 8672–8677.
6
(33) Das, S.; Dubsky, P.; van den Berg, A.; Eijkel, J. C. T. Concentration Polarization in
7
Translocation of DNA through Nanopores and Nanochannels. Phys. Rev. Lett. 2012,
8
108, 138101.
9
10
11
12
(34) Mishra, S.; Varanasi, S.; Varanasi, P. P. A polyelectrolyte Brush Theory. Macromolecules 1989, 22, 4173–4179. (35) Zhulina, E. B.; Borisov, O. V. Structure and Interaction of Weakly Charged Polyelectrolyte Brushes: Self-Consistent Field Theory. J. Chem. Phys. 1997, 107, 5952–5967.
13
(36) Swift, T.; Swanson, L.; Geoghegan, M.; Rimmer, S. The pH-Responsive Behaviour of
14
Poly(acrylic acid) in Aqueous Solution is Dependent on Molar Mass. Soft Matt. 2016,
15
12, 2542–2549.
16
(37) Akcora, P.; Liu, H.; Kumar, S. K.; Moll, J.; Li, Y.; Benicewicz, B. C.; Schadler, L.
17
S.; Acehan, D.; Panagiotopoulos, A. Z.; Pryamitsyn, V.; Ganesan, V.; Ilavsky, J.;
18
Thiyagarajan, P.; Colby, R. H.; Douglas, J. F. Anisotropic Self-Assembly of Spherical
19
Polymer-Grafted Nanoparticles. Nature 2009, 8, 354–359.
20
(38) Wu, T.; Efimenko, K.; Vlcek, P.; Subr, V.; Genzer, J. Formation and Properties of
21
Anchored Polymers with a Gradual Variation of Grafting Densities on Flat Substrates.
22
Macromolecules 2003, 36, 2448–2553.
23
24
(39) Auroy, P.; Auvray, L.; Leger, L. Characterization of the Brush Regime for Grafted Polymer Layers at the Solid-Liquid Interface. Phys. Rev. Lett. 1991, 66, 719–722. 35
ACS Paragon Plus Environment
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
1
(40) Ohno, K.; Morinaga, T.; Takeno, S.; Tsujii, Y.; Fukuda, T. Suspensions of Silica
2
Particles Grafted with Concentrated Polymer Brush: Effects of Graft Chain Length
3
on Brush Layer Thickness and Colloidal Crystallization. Macromolecules 2007, 40,
4
9143–9150.
5
6
(41) Feng, J.; Haasch, R. T.; Dyer, D. J. Photoinitiated Synthesis of Mixed Polymer Brushes of Polystyrene and Poly(methyl methacrylate). Macromolecules 2004, 37, 9525–9537.
7
(42) Hansen, P. L.; Cohen, J. A.; Podgornik, R.; Parsegian, V. A. Osmotic Properties
8
of Poly(Ethylene Glycols): Quantitative Features of Brush and Bulk Scaling Laws.
9
Biophys. J. 2003, 84, 350–355.
10
(43) Xia, F.; Guo, W.; Mao, Y.; Hou, X.; Xue, J.; Xia, H.; Wang, L.; Song, Y.; Ji, H.;
11
Ouyang, Q.; Wang, Y.; Jiang, L. Gating of Single Synthetic Nanopores by Proton-
12
Driven DNA Molecular Motors. J. Am. Chem. Soc. 2008, 130, 8345–8350.
13
(44) de Groot, G. W.; Santonicola, M. G.; Sugihara, K.; Zambelli, T.; Reimhult, E.; V¨or¨os,
14
J.; Vancso, G. J. Switching Transport through Nanopores with pH-Responsive Polymer
15
Brushes for Controlled Ion Permeability. ACS Appl. Mater. Interfaces 2013, 5, 1400–
16
1407.
17
(45) Hou, X.; Guo, W.; Xia, F.; Nie, F-Q.; Dong, H.; Tian, Y.; Wen, L.; Wang, L.; Cao, L.;
18
Yang, Y.; Xue, J.; Song, Y.; Wang, Y.; Liu, D.; Jiang, L. A Biomimetic Potassium Re-
19
sponsive Nanochannel: G-Quadruplex DNA Conformational Switching in a Synthetic
20
Nanopore. J. Am. Chem. Soc. 2009, 131, 7800–7805.
21
(46) Xie, G.; Tian, W.; Wen, L.; Xiao, K.; Zhang, Z.; Liu, Q.; Hou, G.; Li, P.; Tian,
22
Y.; Jiang, L. Chiral Recognition of L-tryptophan with Beta-cyclodextrin-modified
23
biomimetic single nanochannel. Chem. Comm. 2015, 51, 3135–3138 .
24
(47) Siwy, Z.; Trofin, L.; Kohli, P.; Baker, L. A.; Trautmann, C.; Martin, C. R. Protein
36
ACS Paragon Plus Environment
Page 36 of 38
Page 37 of 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
The Journal of Physical Chemistry
1
Biosensors Based on Biofunctionalized Conical Gold Nanotubes. J. Am. Chem. Soc.
2
2010, 127, 5000–5001.
3
(48) Ali, M.; Neumann, R.; Ensinger, W.; Sequence-Specific Recognition of DNA Oligomer
4
Using Peptide Nucleic Acid (PNA)-Modified Synthetic Ion Channels: PNA/DNA Hy-
5
bridization in Nanoconfined Environment. ACS Nano 2005, 4, 7267–7274.
6
7
8
9
10
(49) Behrens, S. H.; Grier, D. G.The Charge of Glass and Silica Surfaces. J. Chem. Phys. 2001, 115, 6716–6721. (50) Kokot, G.; Bespalova, M. I.; Krishnan, M.Measured Electrical Charge of SiO2 in Polar and Nonpolar Media. J. Chem. Phys. 2016, 145, 194701. (51) Okamoto, R.; Onuki, A. Ionization at a Solid-Water Interface in an Applied Electric
11
Field: Charge Regulation. J. Chem. Phys. 2016, 145, 124706
12
.
37
ACS Paragon Plus Environment
The Journal of Physical Chemistry
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 ACS Paragon Plus Environment
Page 38 of 38