Methanol from CO2 by Organo-Cocatalysis: CO2 Capture and

Nov 14, 2014 - Methanol from CO2 by Organo-Cocatalysis: CO2 Capture and Hydrogenation ...... Methanol Reforming in the Context of the Methanol Economy...
1 downloads 0 Views 1MB Size
Subscriber access provided by Library, Special Collections and Museums, University of Aberdeen

Article

Methanol from CO2 by Organo-Co-Catalysis - CO2 Capture and Hy-drogenation in One Process Step Christian Reller, Matthias Pöge, Andreas Lissner, and Florian O.R.L. Mertens Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/es503914d • Publication Date (Web): 14 Nov 2014 Downloaded from http://pubs.acs.org on November 16, 2014

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 27

Environmental Science & Technology

1

Methanol from CO2 by Organo-Co-Catalysis - CO2

2

Capture and Hydrogenation in One Process Step

3

Christian Reller, Matthias Pöge, Andreas Lißner and Florian O.R.L Mertens*

4

Institut für Physikalische Chemie, Technische Universität Bergakademie Freiberg, Leipziger

5

Straße 29, 09599 Freiberg (Germany)

6

ABSTRACT: Carbon dioxide chemically bound to alcohol-amines was hydrogenated to

7

methanol under retrieval of these industrially used CO2 capturing reagents. The energetics of the

8

process can be seen as a partial cancellation of the exothermic heat of reaction of the

9

hydrogenation with the endothermic one of the CO2 release from the capturing reagent. The

10

process provides a means to significantly improve the energy efficiency of CO2 to methanol

11

conversions.

12

INTRODUCTION

13

In recent years, the regard of CO2 has changed from a mere waste product to an attractive low

14

energy chemical feedstock obtainable from fossil fuel and biomass combustion processes or

15

biogas production.

16

converting CO2 by catalytic hydrogenation into valuable base chemicals or fuels, i.e. the

17

conversion to products such as formic acid, methanol, and methane.

18

of CO2 to the latter two products is strongly exothermic, a recovery of the heat of reaction and its

19

utilization in the overall process is mandatory in order to be energy efficient. Two areas for the

1-4

Great efforts have been devoted to the development of processes for

5-7

Since the hydrogenation

ACS Paragon Plus Environment

1

Environmental Science & Technology

Page 2 of 27

20

utilization of the process heat are conceivable, which are the hydrogen production and the CO2

21

separation from flue gas or biogas. In respect to the first option, recent projects have focused on

22

the development of more efficient high temperature electrolysis (Solid Oxide Electrolysis Cells)

23

and the utilization of the recovered heat for preheating and vaporization of water before it is

24

converted in the electrolyzer. The second option would be the use of the heat of reaction of the

25

CO2 hydrogenation in the CO2 recovery from the absorbing or capturing reagents that were used

26

to extract the CO2 from gaseous sources such as flue gas or biogas. As industrial capturing

27

reagents, alcoholamines are typically used. It is important to note that these reagents not only

28

physically but also chemically bind the CO2 molecule and that the absolute value of the enthalpy

29

that is needed to release the CO2 molecule from the capturing reagents again is comparable to the

30

one needed for its hydrogenation (for example for mono-ethanolamine (MEA) the CO2 release

31

enthalpy is ∆H353K =+88.91 kJ/mol while the reaction enthalpy for the CO2 hydrogenation to

32

CH3OH gas and H2O(liq) is ∆H353K= -93.5 kJ/mol. 8,9

33

In respect to this situation, the work presented here started out from two questions. First, if CO2

34

is separated by conventional means, which is its capture by amines or alcohol-amines, it has

35

undergone a chemical fixation that fully changes the nature of its chemical bonds.

36

that not be seen as a sort of chemical activation, which should allow a more efficient

37

hydrogenation process? Second, if the hydrogenation of CO2 is exothermic and the release of

38

CO2 from the capture reagent endothermic, should it not be possible to avoid the strong heat

39

effects by directly hydrogenating the CO2-laden capture reagent? In this way the two processes

40

CO2 hydrogenation and release from the capture reagent would be joined in one process step and

41

an energetic shortcut of the heats of reaction that accompany these two processes would have

42

occurred, leading to a strong energy efficiency gain because much less heat is produced during

6

If so, can

ACS Paragon Plus Environment

2

Page 3 of 27

Environmental Science & Technology

43

this new process. In this contribution, we present a method in which the captured and chemically

44

activated CO2 is directly hydrogenated to methanol under retrieval of the capturing reagent und

45

thus the energy demanding stripping processes can be omitted, completely (see Scheme 1).

46 47

Scheme 1. Corresponding CCU (carbon capture and utilization) process based on DEEA. The

48

stripping process was replaced by in-situ hydrogenation. The scrubbing/capturing reagent was

49

recovered after the distillation of water and methanol.

50

In order to increase the life time of the technical Cu/ZnO-Al2O3 catalysts in the classical

51

methanol syngas synthesis, there is a general attempt to lower the reaction temperature and to

52

work directly with syngas in the liquid phase, i.e. in mineral oils or alcohols as solvents, to

53

improve the heat conductivity of the system. 10-15

54

As part of the attempt to combine syngas chemistry with fossil energy power plant operations by

55

the so called Integrated Gasification Combined Cycle (IGCC), the so called LPMeOHTM process

56

was implemented on pilot plant scale by Air Products in the 1990ies and intensively studied.

57

In this process the catalyst is suspended in mineral oils and the reaction takes place in slurry

11

ACS Paragon Plus Environment

3

Environmental Science & Technology

Page 4 of 27

58

bubble column reactors These studies demonstrated that in the case of methanol from syngas

59

liquid phase processes can have the potential to compete economically with the standard gas

60

phase process because of the much improved heat removal from the reaction zone. Beside some

61

specific benefits connected to syngas chemistry, like being able to directly process syngas which

62

is rich in carbon oxides (CO and CO2), the process demonstrates possible benefits that will also

63

hold for the proposed process such as compact system construction (small heat exchanger

64

volume), continuous catalyst exchange, and robustness to sharp transient operations.10,11

65

In processes in which alcohol is added, it known that it esterifies with the surface-bound formic

66

acid species (b-HCOO-) to form alkyl formates, which were catalytically hydrogenated to

67

methanol and the corresponding alcohol in a subsequent reaction step.

68

temperature in the proposed procedure is reduced because the overall heat of reaction is much

69

lower, it nevertheless somewhat resembles these known procedures because many amine based

70

effective CO2 capturing/scrubbing agents also possess OH groups (alcohol-amines), which may

71

also react with the (b-HCOO-) species to formic acid esters. In addition, amines have also been

72

used as thermodynamic auxiliary reagents in the homogeneously conducted hydrogenation of

73

CO2 to formic acid (see Figure S1). The driving force, i.e. the additional gain in free energy, in

74

these reactions was clearly attributable to the formation of the corresponding ammonium salts.16

75

EXPERIMENTAL SECTION

76

General Methods: All operations were carried out using standard Schlenk and glove box

77

techniques under an atmosphere of argon 5.0. The CO2 hydrogenation processes were conducted

78

in a PTFE-lined 50 ml stainless steel pressure vessel under magnetic stirring. In all time-

79

dependent experiments, the sample extraction of the liquid phase was done with a riser without

80

depressurizing the autoclave. Gases: Hydrogen 5.0 (Praxair), carbon dioxide 4.8 (Praxair) were

12-15

Although the

ACS Paragon Plus Environment

4

Page 5 of 27

Environmental Science & Technology

81

used without further purification. All solvents were also used without further purification. The

82

1

83

solvent CDCl3. Off-line GC analysis was performed on an Agilent 6890 N gas chromatograph

84

equipped with a HP 7694 E headspace sampler. A 30 m Supelco SPB™-1 (0.32 mm diameter;

85

film: polymethyl-silanes) column was used for separation. The GC samples were thermostated at

86

353 K for 20 min before they were transferred by a helium stream (ß=1.2 ml/min) into the

87

injector manifold. The injector temperature was 523 K and a 1:5 split was used. A linear

88

temperature program from 313 K to 453 K (ß=10 K/min) was chosen for the analyte separation

89

and the latter temperature was held for 2 min. GC calibration and further details are described in

90

the Supporting Information, SI. The composition investigation of the supernatant gas phase of

91

the reaction procedure was performed using a Pfeiffer Vacuum Omnistar residual gas analyzer.

92

The calorimetric measurements were carried out with a Setaram C80 calorimeter. The

93

calorimetric cell with a volume of 7.5 ml was filled with 19.9 mmol DEEA and evacuated to its

94

vapor pressure. Afterward the setup was left to equilibrate for 5 hrs (separate tests showed that

95

the mass loss due to the evacuation procedure is less than 1 percent). Subsequently, the cell was

96

connected to a CO2 filled gas reservoir (1953 mbar, 15.7735 ml) resulting in a pressure drop to

97

1188 mbar from which an overall gas volume of 25.93 ml (gas reservoir, calorimetric cell and

98

tubing) was calculated.

99

Hydrogenation: 20 ml DEEA and 300 mg Cu/ZnO-Al2O3 catalyst were filled in a 50 ml PTFE

100

lined autoclave under inert conditions. The mixture was heated to the desired temperature and

101

pressurized with 20 bars of CO2 until the solvent became saturated. After the system reached its

102

equilibrium, gaseous hydrogen was introduced (pH2=50-70 bar). The reaction procedure was

H and 13C NMR spectra were recorded on a Bruker Avance III 500 spectrometer using the NMR

ACS Paragon Plus Environment

5

Environmental Science & Technology

Page 6 of 27

103

surveyed by internal pressure measurement and by time resolved sample extraction over a riser

104

followed by subsequent GC and NMR analysis.

105

Catalyst preparation: The preparation of the catalyst Cu/ZnO-Al2O3 follows mainly the method

106

given in Ref. [17]. A 0.1M metal salt solution was prepared by dissolving 8.92 g Zn(NO3)2·4H2O

107

(0.03 mol), 14.449 g Cu(NO3)2·3H2O (0.06 mol), and 3.75 g Al(NO3)3·9H2O (0.01 mol) in 100

108

ml distilled H2O. The co-precipitation agent was a 1.6M solution of Na2CO3 (17 g/ 100 ml). The

109

pH and temperature controlled co-precipitation was performed at T=65 °C and pH=6.8 in 400 ml

110

distilled water. The slurry was aged under continuous stirring for 60 min. The precipitate was

111

filtered off and washed free from alkaline ions before it was dried at T=80 °C overnight. For the

112

calcination the catalyst was heated with 2K/min from ambient temperature to T=330 °C in an

113

Ar/O2 80/20% mixture and kept there for 3 h. The catalyst was then slowly cooled in a mixture

114

of 10% H2 in Ar to 280 °C (1 K/min) and kept at that temperature for 2 hours. The reduction

115

properties of the Cu, Zn, and Al oxides were investigated by temperature programmed reduction

116

(for further details see Supporting Information).

117

RESULTS AND DISCUSSION

118

Since N,N-Diethylethanolamine (DEEA) is capable of O-activating CO2 by zwitterion formation

119

under anhydrous conditions, the chemical modification of CO2 affects the course of the

120

hydrogenation mechanism and may lead to a more attractive synthesis route to methanol.

121

However, it has to be mentioned that not all alcoholamines can promote a chemical activation of

122

CO2 and that the procedure is limited to non-aqueous solvents because of the zwitterion

123

decomposition to HCO3- in the presence of water.

124

during the hydrolysis of carbamates in the case of MEA and DEA (diethanolamine).

125

Figure S8). In the work presented here, the alcoholamine DEEA was predominantly used as

18

A similar phenomenon is also observed 19

(see

ACS Paragon Plus Environment

6

Page 7 of 27

Environmental Science & Technology

126

scrubbing and activation agent, because it proved to be stable over a wide temperature range (25

127

°C- 170 °C) in the applied hydrogenation procedure.

128

At first, we investigated the hydrogenation of CO2 in the pure scrubbing solvent DEEA (20 ml,

129

300 mg Cu/ZnO-Al2O3) at two different temperatures, 100 °C and 170 °C. After reaching the

130

desired reaction temperature the autoclave was pressurized with 10 bar of CO2. After the

131

absorption equilibrium was reached and the solvent was saturated, the autoclave was further

132

pressurized with 60 bar hydrogen resulting in a total pressure of 70 bar. The subsequent pressure

133

drop resulting from the reaction was recorded as a function of time. Figure 1 illustrates the time-

134

resolved GC-analysis of the product concentrations at different reaction stages of a

135

hydrogenation performed at T=100 °C. Gas chromatographic measurements were used for

136

product quantification.

137

From the 13C NMR analysis (Figure S2) in the time period from 30 min to 360 min after start of

138

reaction, one can conclude that the hydrogenation of CO2 performed at T=100 °C leads to an

139

initial formation of 2-diethylaminoethyl formate (δ=160 ppm, 13C NMR) indicated by the proton

140

resonance at δ =8 ppm (see 1H NMR Figure S2). It is further illustrated that the physically

141

dissolved CO2 content simultaneous decreased (see δ = 125 ppm,

142

with the pressure drop in the reactor. The corresponding

143

were extracted after 3h, 12h, and 24h show an increasing amount of methanol (δ =49.2 ppm)

13

13

C NMR) which coincides

C NMR spectra of samples which

144

ACS Paragon Plus Environment

7

Environmental Science & Technology

Page 8 of 27

145 146

Figure 1. Hydrogenation experiment at T=100 °C, p(CO2)=10 bar , p(H2)=60 bar, catalyst

147

loading 300 mg. Chromatograms of the DEEA solvent as received and the reaction solution

148

measured after 3h, 12h and 24h reaction time. The corresponding 1H NMR spectrum measured

149

after 3h is displayed in Figure S2.

150

and of 2-diethylaminoethyl formate (δ =160 ppm). The chromatogram of a sample that was

151

extracted after 3h indicates the formation of methanol as the main product. The peak areas were

152

calibrated using an external standard (see Supporting Information). It is also noticeable that even

153

at longer reaction periods, the methanol content does not remarkably increase, but the peak of the

154

2-diethylaminoethyl formate species continues to grow. The product quantification from the

155

corresponding GC analysis after 3h of reaction resulted in a yield to methanol of 5.4 %. From the

156

corresponding 1H NMR integration we determined the yield to 2-diethylaminoethyl formate to be

157

49 %. All yield numbers are calculated in respect to the total amount of CO2 added to the

158

autoclave at the beginning of the experiment. Due to the simultaneous occurrence of solution of

159

CO2, in physical and chemical form, and the reaction, we did not determine the amount of the

160

reactant CO2 after the reaction was terminated. Consequently, we can only state a minimal

161

conversion of about 54 % in this experiment. To improve the measurements in this respect

ACS Paragon Plus Environment

8

Page 9 of 27

Environmental Science & Technology

162

extensive CO2 and hydrogen solubility studies with pure DEEA are needed. The methanol

163

activity (MTY) of the catalyst at T=100 °C was determined to be 0.542 mmol/ (kg-cat*h). In a

164

second experiment we raised the temperature to 170 °C and determined the composition of the

165

reaction mixture after 6h by NMR and GC-analysis (see Figure 2). The yield to methanol was

166

determined to be 30 % which resulted in a methanol activity (MTY) of 1640 mmol/ (kg-cat*h).

167

The characteristic signals of 2-diethylaminoethyl formate (13C NMR; δ =160 ppm and 1H NMR δ

168

=8 ppm) noticeably disappeared which leads to the conclusion that the formate species was fully

169

converted to methanol at this temperature. Only small amounts of the formate were detected by

170

gas chromatography (see Figure 2b). Running the experiment for 12 h resulted in a yield to

171

methanol of 60%. In the early beginning (first 3 h), an initial formation of the ester species 2-

172

diethylaminoethyl formate was also observed, as it was previously mentioned for the 100 °C

173

experiment. The NMR spectroscopic investigation (Figure 2a) also confirmed that at T=170 °C

174

the DEEA itself was not hydrogenated to Et3N over the monitored reaction period. At higher

175

temperatures, T>200 °C, DEEA hydrogenation products became detectable. In addition, the

176

supernatant gas phase present after the reaction (170 °C, 6h) was also investigated by mass

177

spectrometry to exclude a significant formation of volatile by- products. Only traces of CO, CH4,

178

and methanol could be

ACS Paragon Plus Environment

9

Environmental Science & Technology

Page 10 of 27

179 180

Figure 2. Hydrogenation experiment of CO2 captured by DEEA at T=170 °C, p(CO2)=20 bar,

181

p(H2)= 60 bar a) 1H NMR (CDCl3) spectrum b) gas chromatogram of the corresponding sample.

182

The samples were taken after 12h. For the analysis of the supernatant gas phase see Figure S3.

183

qualitatively identified in the gas phase of the autoclave (see Figure S3). Regarding the fact that

184

in the 170 °C experiment methanol is essentially the sole product after 6h and thus the selectivity

185

is close to 1, the given yield number equals the one for the conversion.

186

In order to elucidate the role of the alcohol function of the alcoholamine in respect to the surface

187

formic acid (b-HCOO-) esterification and zwitterion formation, pure formic acid pre-esterified

188

alcoholamine (2-diethylaminoethyl formate) was used as starting material and subjected to the

189

catalytic hydrogenation in a test reaction. The analyses of the 1H and 13C NMR spectra in Figure

190

S4 provided evidence that the catalyst Cu/ZnO-Al2O3 facilitates the direct hydrogenation of the

191

ester at T=150 °C to methanol. At 170 °C the result indicates only faster kinetics. In addition,

192

we tried to clarify the role of the zwitterion in the hydrogenation mechanism. Since in pure

193

DEEA, the zwitterion is the only ionic species produced by CO2 absorption, its formation can be

194

monitored by electric conductivity measurements which we carried out at different temperatures

ACS Paragon Plus Environment

10

Page 11 of 27

Environmental Science & Technology

195

(30 °C, 50 °C, and 100 °C) and CO2 partial pressures (see Figure 3). The obtained results suggest

196

that the formation of the zwitterion mainly depends on the selected temperature range. At T=100

197

°C no conductivity increase was found even at high CO2 partial pressures p(CO2)=45 bar. While

198

at T=50 °C only a small increase in conductivity occurred with the increase of the CO2 partial

199

pressure, at T=30 °C a much stronger one caused by the increase of the zwitterion concentration

200

was observed. From these results one can conclude that the activation mechanism based on

201

zwitter-ionic species should be relevant only at temperatures below 100 °C. In the temperature

202

range between 20-50 °C 2-diethylaminoethyl formate is, thus, on one hand formed by the known

203

esterification of surface bound formic acid with the alcohol function,

204

the other hand by direct hydrogenation of the zwitterion. The ester therefore represents a key

205

compound in the described CO2 hydrogenation pathway to methanol. In a second test experiment

206

it was examined whether or not the surface formic acid can be neutralized directly by the

207

alcoholamine which may finally result in the formation of an ionic liquid (IL). To ascertain the

208

role of the ionic liquid [DEEAH+HCOO-] in the CO2 activation procedure, we examined if the

209

catalytic hydrogenation of pure [DEEAH+HCOO-] is possible. During the attempt of the direct

210

hydrogenation of the pure ionic liquid (for its preparation see Supporting Information), a

211

significant pressure increase in the autoclave has been registered, suggesting the decarboxylation

212

of the compound.

13

here of DEEA, and on

ACS Paragon Plus Environment

11

Environmental Science & Technology

Page 12 of 27

213 214

Figure 3. Conductivity measurements of non-aqueous DEEA exposed to a CO2 atmosphere

215

(150 ml, T=30 °C, 50 °C, and 100 °C) indicating the formation of the zwitter-ionic species.

216

With the help of 1H NMR spectroscopy after a reaction period of 24 h (see Figure S5a), only

217

pure DEEA was found in the liquid phase. In order to determine the decomposition temperature

218

of the ionic liquid and to identify the gaseous decomposition products, we subjected it to TG-

219

DSC measurements and simultaneously analyzed the emitted gas species by coupled FT-IR

220

spectroscopy. In the decomposition experiment of the ionic liquid, an endothermic signal

221

(decarboxylation) was observed at T= 120 °C (see Figure S5b) and only the products DEEA and

222

CO2 were detected in the exit gas stream (see Figure S5c). By these measurements, the formation

223

of undesired CO during the decomposition of the ionic liquid can be ruled out for the desired

224

temperature range (120-170 °C). In respect to the hydrogenation reaction, it can be concluded

225

that the formation of the ionic liquid is not essential for the formation of methanol at T>120 °C

226

due to its decomposition behavior.

227

Similarly, it can also be concluded that there will be a noticeable concentration of the IL at

228

reaction temperatures below 100 °C, because the thermal decomposition does not occur. Based

229

on the performed hydrogenation experiments and particularly on the temperature variation

ACS Paragon Plus Environment

12

Page 13 of 27

Environmental Science & Technology

230

experiments, it became clear that a wide variety of CO2 conversion pathways for the

231

alcoholamine DEEA CO2 system (Figure 4) does exist. From thermodynamic calculations it is

232

known that the formation of the ionic liquid provides an energetic contribution (thermodynamic

233

driving force) to the initial formation of formic acid from CO2 at temperatures T