Microfluidic System for Rapid Detection of Airborne Pathogenic Fungal

Subscriber access provided by Kaohsiung Medical University

Article

A microfluidic system for rapid detection of airborne pathogenic fungal spores Xiaoxu Li, Xinlian Zhang, Qi Liu, Wang Zhao, Sixiu liu, and Guodong Sui ACS Sens., Just Accepted Manuscript • DOI: 10.1021/acssensors.8b00615 • Publication Date (Web): 28 Sep 2018 Downloaded from http://pubs.acs.org on September 29, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

1

A microfluidic system for rapid detection of airborne pathogenic

2

fungal spores

3

Xiaoxu Li, 1 Xinlian Zhang, 1 Qi Liu, 1 Wang Zhao,1 Sixiu Liu, 1 Guodong Sui, *, 1, 2, 3

4

*To whom correspondence shall be addressed.

5

1

6

of Environmental Science & Engineering, Fudan University, 220 Handan Road, Shanghai, 200433,

7

P. R. China.

8

2

9

3

10

Shanghai Key Laboratory of Atmospheric Particle Pollution and Prevention (LAP3), Department

Shanghai Institute of Pollution Control and Ecological Security, Shanghai 200092, P. R. China

Institute of Biomedical Science, Fudan University, No. 138 Yixueyuan Road, Shanghai 200032, P.

R. China

11 12 13 14 15 16 17 18 19 20 21 22 23 24

ACS Paragon Plus Environment

ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

25

ABSTRACT: Airborne fungi, including Aspergillus species, are the major causes of human

26

asthma. Direct capture and analysis of pathogenic fungi in indoor air is important for disease

27

prevention and control. In this paper, we demonstrated an integrated microfluidic system capable

28

of enrichment and high-throughput detection for airborne fungal spores of Aspergillus niger, a

29

well-known allergenic harmful species. The microfluidic system allowed semi-quantitative

30

detection of Aspergillus niger spores based on immunofluorescence analysis. To assess its

31

contaminated level, the whole analysis time could be completed in 2-3 hours including ~1h of

32

enrichment and ~1h of target detection. The detection limit was ~20 spores, equivalent to ~300

33

spores·m-3 of the concerned targets in air. In addition, the microfluidic system has integrated

34

sampling and sample analysis to avoid additional sample concentration step, showing the potential

35

for point-of-care detection for other pathogenic fungal spores.

36

KEYWORDS: Microfluidic system, Pathogenic fungi, Aspergillus niger spores, Enrichment,

37

Immunoassay analysis

38 39 40 41 42 43 44 45 46


Page 2 of 33

Page 3 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

47

Fungi are commonly found indoors since they can colonize every inch of a room yet are scarcely

48

associated with health effects in low concentration.1 In the presence of dampness, fungi are able to

49

proliferate explosively to damage building materials,2-4 they can also invade and infect human

50

body by means of releasing numerous spores as well as various harmful secondary metabolites

51

such as carcinogenic mycotoxins into the air.1,2,5,6 Adverse effects of poor indoor air quality

52

caused by fungal aerosol contamination on health have attracted much public attention, since

53

people spend almost 90% of their time indoors.7-9 These undesirable bio-aerosols can lead to sick

54

building syndrome (SBS) and building related illness (BRI),10 for instance, some sensory

55

irritations of eyes and upper respiratory tract induced by volatile products of fungal

56

metabolisms,11-13 and some respiratory infections and allergic reactions caused by airborne fungal

57

spores13,14 including Penicillium, Aspergillus, Cladosporium, etc. Additionally, evidence showed

58

that some pathogenic species can cause nosocomial infections which are always focal issues.15

59

Especially for immunocompromised individuals such as transplant patients, most infections

60

known as invasive fungal infections (IFIs) occur in their lungs because of inhalation of fungal

61

spores among which Aspergillosis is the most common one.15-17 The IFIs can then spread to other

62

systems of the body, and even lead to death.18,19 Among pathogenic Aspergillosis species,

63

Aspergillus niger (A. niger) is one of the most common causes of IFIs. The previous studies have

64

reported20 that the IFI caused by A. niger could infect a leukemic patient’s heart and develop into

65

pericarditis and cardiac tamponade month after bone marrow transplantation. Moreover, the A.

66

niger could also cause mycosis of ear and primary cutaneous aspergillosis and produce

67

nephrotoxic and carcinogenic mycotoxin.21 However, evidence for the casual dose-response

68

relationship between these molds and human health is still poorly documented.


ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

69

Due to high risks of fungal exposure, mold management has received extensive attentions,

70

including regular inspection, elimination of moisture sources, removal of the viable mycelia from

71

surfaces and filtration of airborne spores from indoor air to prevent indoor fungal growth.4,22

72

Although eradication of fungal-polluted materials can stop the production of new spores and their

73

dispersals, the residual fungal allergens settled in dust may cause episodic allergy symptom in

74

sensitive individuals with a long duration.23 In addition, some fungi sources could hide in the

75

building structure such as wall insulating layers to avoid elimination,24,25 furthermore, indoor

76

microbiomes are usually a mixture of species resembling in outdoor environment. Overall, indoor

77

microbiomes are usually changeable and complex mixture that are mainly influenced by dispersal

78

from outdoor biomes.26 In densely populated buildings such as hospital, the microbial load,

79

attributable to pathogenic problem species such as Penicillium or Aspergillus, is affected not only

80

by nature factors, more often impacted by number of occupants, their activity, building ventilation,

81

and so on.25,26 To completely avoid fungal exposure is not practical, instead, focusing on those

82

problem species might be alternative to effectively reduce the risks of exposure.

83

In order to effectively control pathogenic fungi exposure, airborne fungi assessment is considered

84

as a reasonable means to directly evaluate the risks of fungal exposure and guide regular mold

85

managements, in spite of the lack of information about dose-response relationship. Air samples are

86

commonly used in various analytical assays to assess human exposure to fungi. Noticeably, air

87

sample analyses are conducive to identify abnormal presence of fungi with hidden mold growth,

88

to detect pathogenic spore releases from sources and to monitor the effects of mold managements.

89

To our best knowledge, there are no standard sampling or analytical methods for airborne

90

pathogenic fungi. Herein, we listed some typical techniques that have been used in studies for


Page 4 of 33

Page 5 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

91

airborne fungi sampling (Table S1) and sample analysis (Table S2). Apart from the culture

92

methods which are time-consuming and inadequate to cultivate all collected microorganisms,

93

researchers have combined some commercial air samplers with advanced analytical techniques.

94

For instance, the Coriolis µ air sampler combined with the quantitative polymerase chain reaction

95

(qPCR) has been used for airborne fungi analysis. Luminex xMAP technique was also introduced

96

in the high-throughput identification of fungi species in the air.27-29 In addition, several

97

supersensitive sensor-based methods for pathogenic Aspergillus spore detection were reported,30,31

98

but these methods could not directly analyze fungal spores from air.

99

Herein, we presented a microfluidic system comprised of a sampling chip and an analysis chip

100

capable of rapid detection of airborne pathogenic fungal spores of A. niger. The system showed

101

high sensitivity and specificity towards specific fungal spores from indoor air. The staged

102

herringbone mixer (SHM) structure was adopted in the sampling chip, which was successful used

103

in the airborne bacteria collection.32-34 For the first time, SHM structure was utilized to capture

104

airborne fungal spores (much larger than bacteria). By employing this technique, the volume of

105

eluent from the sampling chip could be controlled in dozens of microliters, which makes it

106

possible to directly introduce the sample into the downstream analysis chip without culturing or

107

concentration steps. The analysis chip has a column structure, combining the nonspecific physical

108

interpretation and specific immunocapture to enrich and identify the target spores. In order to

109

assess the number of A. niger spores in air sample, the semi-quantitative standard curve of

110

immunofluorescence intensity-number of spores were established. Furthermore, the sensitivity and

111

specificity of the system was evaluated by mimic spore-aerosols. The system has potential to

112

implement high-throughput detection of different specific fungal species by using corresponding


ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

113

immune labels.

114

METHODS AND MATERIALS

115

Materials and Reagents. Photoresists (SU-8 2005, SU-8 2025) were purchased from Microchem

116

(USA). Photoresist (AZ-50XT) was purchased from AZ Electronic Materials USA Corp.

117

Polydimethylsiloxane (PDMS, RTV-615-044) was purchased from Momentive Specialty

118

Chemicals (USA). Carboxyl-modified microspheres (PS-COOH) were purchased from Bang’s

119

Laboratory (USA). The fungal strain Aspergillus niger (A. niger, CGMCC No. 3.6469) and

120

Aspergillus oryzae (A. oryzae, CGMCC No. 3.39544) were obtained from China General

121

Microbiological Culture Collection Center (CGMCCC). Anti-Aspergillus niger polyclonal

122

antibodies (IgG) were purchased from Virostat (Portland). Anti-Aspergillus niger monoclonal

123

antibodies (MCA 2576) and fluorescein isothiocyanate-labeled (FITC) anti-Mouse secondary

124

antibodies were purchased from Bio-Rad (USA). Sabouraud dextrose agar was purchased from

125

Oxoid (UK). All other reagents were purchased from Sigma (USA).

126

Microfluidic Chip Fabrication. The presented system is consisted of an enrichment chip for

127

fungi spores collect from air and a detection chip for immunofluorescence analysis of collected

128

pathogenic spores. Both chips were designed by AutoCAD 2014 software (Autodesk, USA) and

129

fabricated following standard soft lithography. The silicon molds of the enrichment chip that

130

patterned with fluidic channels and herringbone structures were made from SU-8 2025. For the

131

detection chip fabrication, the silicon mold of the control layer was made from SU-8 2025 and the

132

mold of the fluidic layer was made from SU-8 2005 and AZ-50XT. The PDMS polymer plates

133

casted from the molds were assembled precisely to separately fabricate the enrichment chip and


Page 6 of 33

Page 7 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

134

the detection chip. Inlet and outlet holes were punched for air or liquid flow. The channel surfaces

135

of the enrichment chip were sequentially washed by HCl (1.0% v/v), H2O2 (1.0% v/v), and

136

deionized water, then dried with clean nitrogen prior to the usage.

137

Fungi Spore Culture and Collection. A. niger and A. oryzae were both grown at 37°C for 2-4

138

days in Sabouraud dextrose agar. Fungal spores were harvested with sterile loops and washed

139

twice with phosphate-buffered saline (PBS, pH 7.2). Harvested spores were suspended in 50 mM

140

carbonate bicarbonate buffer (pH 9.6) to obtain the suspension of ~1.1 × 106 spores·mL-1 (~0.05

141

mg·mL-1). The spore suspensions were stored at 4°C and used within 2 weeks.

142

Spore-aerosol Generation and Spore Collect on the Enrichment Chip. To validate the

143

performance of the enrichment chip, simulated spore-aerosols of A. niger was generated and

144

monitored. The schematic diagram of the spore-aerosol generation system was shown in

145

supplementary information Figure S1. A mini generator (DIONE N7, China) charged with 5 mL

146

of prepared spore suspension (~1.1 × 106 spores·mL-1) was introduced to spray spore-aerosol

147

droplets into a closed generation cube (750 mm × 450 mm × 450 mm) with an atomization rate of

148

800 µL·min-1 (shown in Figure 3A). To rapidly distribute spore-aerosols, a turbulator was placed

149

in the middle of the cube bottom. At 100 mm height above upper surface of the turbulator, a wind

150

sensor (MIK-GWT 0-5 m·s-1, China) was set to measure its airflow speed. A particle matter

151

monitor (PLANTOWER PMS5003T, China) was used to monitor particle concentration in

152

real-time manner. For spore-aerosol generating, the mini generator which was loaded with 1.1 ×

153

106 spores·mL-1 suspension executed the atomization for 1 min only at the beginning and then 10 s

154

supplementary atomization every other 20 seconds. The generated aerosols were immediately

155

dispersed by the 0.3 m·s-1 airflow blown from turbulator. The stability of generated aerosols was


ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

156

measured by APS (Aerodynamic Particle Sizer, TSI3321-APS, USA). Briefly, the sample mode of

157

APS was a summed mode; sheath flowrate, 4.0 L·min-1; sample flown, 5.0 L·min-1; sample type,

158

continuous; inlet pressure, 1000 Mbar; detection range, 3-20 µm (aerodynamic diameter);

159

sampling time, 20 s. When collecting spores using the enrichment chip, two micro-vacuum air

160

pumps (HARGRAVES, USA) assembled in parallel were connected to the airflow outlet of the

161

enrichment chip and drew the aerosol into the enrichment chip.

162

To evaluate the collection efficiency of the enrichment chip, the testing system (shown in Figure

163

S2) was established to collect the uncollected spores in the filtered air. The traditional

164

sedimentation method was used as control. Spores collecting by the enrichment and the traditional

165

sedimentation method were both collected in PBS and diluted 100 times, respectively. Collected

166

spores were then counted by the hemocytometer.

167

To evaluate specificity of the detection chip for identifying A. niger spores, the A. niger

168

suspension of 1.1 × 106 spores·mL-1 was mixed with A. oryzae suspension of 1.1 × 106

169

spores·mL-1 in ratios of 3: 1 and 1: 3, respectively. Then the generator was charged with different

170

suspensions containing 100%, 75%, and 25% A. niger spores, respectively. Later, different

171

suspensions were atomized into the cube following the above generation steps. The sampling time

172

of each spore-aerosol was 5 min (~500 spores could be collected). Spores collected by the

173

enrichment chip were washed in 20-30 µL PBS for subsequent detections.

174

Analysis on the Detection Chip. Microspheres of 20.38 µm diameter was adopted for both

175

interception and immunocapture of specific spores. The interaction between PS-COOH and

176

Rabbit polyclonal antibody is covalent. Figure 2A was illustrated the schema of immunoassay


Page 8 of 33

Page 9 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

177

reactions for A. niger spores detection on microspheres. Following protocol from Bangs

178

Laboratories, Inc., the carboxyl-modified microspheres were firstly immobilized with rabbit

179

polyclonal antibodies (4-5 mg·ml-1) and the final microspheres with rabbit polyclonal antibodies

180

were ~10 µg·µl-1. Then microspheres with rabbit polyclonal antibodies were loaded into reaction

181

channels of the detection chip. For spore capture and analysis, 20 µL PBS-Tween-20 solution was

182

used to rinse protective solution off before sample loading. The whole analysis procedure was

183

schematically illustrated in Figure 2B. The spore analysis on the chip was conducted as following

184

steps: (1) Sample loading. Washing buffer containing collected fungal spores was injected into the

185

reaction channel via the inlet with the flowrate of 6 µL·min-1. (2) Blocking and specific marking.

186

20 µL PBST solution containing 1% bull serum albumin (BSA) was used to wash and block the

187

residual antibodies on the microspheres, and then 5 µL monoclonal antibody solution (1.0 mg·ml-1)

188

was introduced into the reaction channel and the chip was incubated at 37°C for 15 min. (3)

189

Washing and Blocking. Above washing and blocking step were repeated. (4) FITC labeling. 5 µL

190

FITC labeled anti-mouse secondary antibody solution (2.0 mg·ml-1) was injected into the reaction

191

channel and the chip was incubated in darkness at 37°C for 15 min. (5) Washing and analysis.

192

PBST solution was used to continuously wash the microspheres for 5 min. Fluorescence images

193

were obtained on the fluorescence microscope (Nikon, Eclipse Ti, Japan) and results were

194

analyzed by the software MATLAB 2016 (MathWorks, USA).


ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

195 196

Figure 1. (A) Image of the microfluidic system for airborne spore-aerosol enrichment and

197

detection: (a) airborne spore enrichment chip, (b) airborne spore detection chip. (B) Schematic

198

illustration of the enrichment chip when sampling air. Air inlets and center outlet remained open.

199

(C) Schematic illustration of the enrichment chip when eluting spores. The center outlet was

200

closed. (D) Image of the detection chip and schematic illustration of the detection chip: (a) fluid

201

layer, (b) control layer. (E) Image and illustration of the detection units on the chip.

202 203

Figure 2. (A) Schematic illustration of immunoassay reactions for A. niger spore detection on


Page 10 of 33

Page 11 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

204

microspheres. (B) Procedures of A. niger spore analysis on the detection chip.

205

RESULTS AND DISCUSSION

206

Design of spore-aerosol detection system. The system consists of an enrichment chip for

207

airborne fungal spore sampling (Figure 1A-a) and a detection chip for analysis of specific

208

pathogenic spore (Figure 1A-b).

209

In the enrichment chip, sixteen identical channels (40 mm long × 0.6 mm wide × 0.04 mm high)

210

with SHM structures were radially arranged from the center of the chip and shared the same center

211

airflow outlet. Each channel had an inlet for air/liquid flow and a joint hole for liquid flow (shown

212

as Figure 1B&C). When sampling air, 16 channels in the enrichment chip could work in parallel

213

by drawing the air from the shared outlet (Figure 1B). The total flow rate of the enrichment chip

214

was ~1.3-1.45 L·min-1 (80-90 ml·min-1 of each channel × 16 channels). The SHM structure was

215

introduced for airborne spore enrichment, which has been demonstrated to efficiently capture

216

airborne bacteria particles from air by adhering bacteria to surfaces of the channel.32,34 This

217

structure could break the laminar airflow into chaotic flow when sampled air flow passing through

218

the channel to improve the contact between fungal spores and inner surfaces of the channel.34,35

219

When eluting spores, the center outlet was closed and 16 channels were connected in series, so

220

that all the channels could be rinsed by injecting washing buffer for only one time (Figure 1C). By

221

adopting this microfluidic chip, the volume of eluent consumed for sample collection could be

222

minimized to 5-10 µl. With such a small volume, all fungal spores in the eluent could be directly

223

analyzed in the downstream detection chip avoiding the traditional concentration operations such

224

as centrifuging and culturing.36,37 In the presented system, the total volume of eluent was set to be


ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

225

20-30 µl due to the downstream detection chip could reconcentrate the target fungal spores to

226

further increase the concentration of fungal spores in the eluent.

227 228

Figure 3. (A). Spore-aerosol generation system. (B). Raw particle counts of A. niger

229

spore-aerosols measured by APS (Generation from 1.1 × 106 cells·ml-1 of A. niger spore

230

suspension). Values are the mean ± s.d. for n = 3.

231

The detection chip (shown in Figure 1D-E) provided 10 identical units, which could analyze 10

232

different samples separately by valve controls without cross contamination. The microfluidic

233

immunoassay chip was 3×3 cm2 in size and composed of a fluidic layer (Figure 1D-a) and a

234

control layer (Figure 1D-b). One outlet (black) was shared by ten channels (blue), while each

235

channel has its own inlet (Figure 1D). The inlets and outlets of fluidic layer were 200µm width


Page 12 of 33

Page 13 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

236

and the reaction column was 100µm width (Figure 1E). The inlet and reaction column of the

237

fluidic layer were 30µm height and the outlet of the fluidic layer was 10µm height. The weir

238

structure between inlet and reaction column can intercept 20.38µm-microsphere to stay in reaction

239

column. Generally, the concentration of airborne spores in air can effectively reflect the fungal

240

contamination. Analyses of nucleic acid are mostly used to identify microorganism species and

241

estimate its quantities.38-40 However, different from bacterial cells, it is difficult to extract DNA

242

from the fungal spores especially in a short time period because of their sturdy cell walls.41,42 Thus,

243

for the rapid analysis of specific pathogenic spores, the detection chip adopted the

244

immunofluorescence method to estimate the quantity of target spores instead of nucleic acid

245

analysis. In the immunoassay process, the immunofluorescence assay efficiency could be directly

246

influenced by the capture efficiency on the chip. Many studies demonstrated that it was an

247

effective means to improve capture efficiency by increasing the contact between antigens and

248

antibodies.43 For example, Wang et al.44 built hundreds of small columns in the microfluidic

249

channels to increase antibody-modified area of inner channel surface and demonstrated the good

250

performance of this structure for circular tumor cell capture. As reported by Wang and Han,45 the

251

reaction kinetics of bead-based antibody-antigen binding can be enhanced, the beads based

252

microfluidic preconcentrator increased the detection sensitivity of immunoassay (by at least 500

253

fold). In presented studies, each unit was equipped with a reaction channel (100 µm wide × 30 µm

254

high) packed with antibody-modified microspheres in a single layer. The microspheres were

255

immobilized by a weir structure which formed at the junction between the reaction channel of 30

256

µm in height and the outlet channel of 10 µm in height (Figure 1E). It could intercept

257

microspheres (20.38-µm diameter) and let liquid flow through during the processes of


ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

258

microsphere packing and sample loading. Compared with direct modification of antibodies on the

259

surface of channels, the microspheres in the channel could provide a larger surface area to modify

260

antibodies for capturing target spores. Meanwhile, the single spore cells in sample would have

261

more chances to touch immobilized antibodies easily when they flow through the tiny gaps

262

between microspheres, which also could improve the capture efficiency. Figure 2A illustrated the

263

process of A. niger capture and detection on the microspheres. The monoclonal antibody was used

264

to identify A. niger spores with high specificity. After the spores were labeled with FITC, the

265

FITC could profile spore cell by emitting green fluorescence under 490 nm excitation.46,47 The

266

amount of target spores was calculated according to the intensity of fluorescence signal.

267

Validation of the enrichment chip. Like other approaches based on fluid mechanics and air

268

dynamics (most of them belong to the impingement method),48,49 its collection efficiency for

269

particles with different sizes and qualities might be different. We firstly testified the feasibility of

270

the enrichment chip for A. niger spores collection. As shown in Figure 3A, the spore-aerosols

271

were generated in the closed cube and monitored by APS to test its stability. The data of six

272

repeated trials was shown in Figure 3B. The figure only showed the numbers of particles from 3.5

273

µm to 12 µm measured by APS due to A. niger spores as the detection objects would form aerosol

274

particles with diameters larger than 3.5 µm50 and particles with diameter larger than 10 µm are

275

easier to combine with water to fall down. This result showed that (1) approximately 75% of

276

particles that detected by APS distributed in the range of 3.5 to 5 µm of aerodynamic diameters

277

which matched with the size of A. niger spore; (2) other particles that smaller than 10 µm might be

278

the particles containing two spores or enwrapped with a thin water film;51 (3) the sampling volume

279

of APS was ~1.67 L each trial (sampling time: 20 s) which was similar to ~1.5 L of the


Page 14 of 33

Page 15 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

280

enrichment chip (working time: 1 min). The result indicated that the concentration of mimic

281

spore-aerosol in the generation cube were stable and it could provide an effective aerosol for the

282

feasibility tests. Subsequently, the enrichment chip was placed in the cube for sampling with 30

283

min and 2 h, respectively. As shown in Figure 4, the spores adhered to the inside wall of channels

284

were observed under the 20× objective. The number of spores collected for 2 h was significantly

285

more than that of 30 min collection. This result directly proved that the enrichment chip could be

286

used for spore-aerosol collection.

287

Table 1. Collection efficiency of enrichment chip with different experimental times. Experimental time (min) 0 10 20 30 40 50 60

Total no. of enriched A. niger spores (cells) 0 10500 23300 31700 45900 62800 91500

Total no. of unenriched A. niger spores (cells) 0 0 600 1700 4600 8900 16000

Enrichment efficiency 0 100% 97.4% 94.6% 90.0% 85.8% 82.5%

288

289 290

Figure 4. Images of enrichment channel on the chip for spore-aerosol capture with different


ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

291

sampling time. (A) sampling time: 0 min, (B) sampling time: 30 min, (C) sampling time: 2 h.

292

In order to investigate the collection efficiency changing with the time, 6 different

293

experimental times were selected to be 10, 20, 30, 40, 50, and 60 min, as shown in Table 1. The

294

cube in testing system (Figure S2) was charged with the spore suspension of 1.1 × 107 cells·ml−1

295

to generate spore-aerosol droplets. During experiments, the spore-aerosol droplets were kept in a

296

saturated state to provide channels of the enrichment chip enough spores for absorption.

297

Experimental data about A. niger spore collection efficiency was shown in Table 1. The results

298

showed that the enrichment chip was well capable of capturing A. niger spores from aerosol. The

299

total numbers of collected spores increased as experimental time prolonged. As the sampling time

300

prolonged from 20 to 60 min, the collection efficiency slightly declined from 97.4% to 82.5%.

301

However, its efficiency was much better than that of the traditional sedimentation method. When

302

the sampling time was 20 min, the collection efficiency of the enrichment chip was 35 times

303

higher than that of the traditional sedimentation method. When sampling time was 60 min, the

304

collection efficiency of the enrichment chip was still 5 times higher than that of the traditional

305

sedimentation method. It is clear that the designed microfluidic chip with SHM structure can

306

capture A. niger spores at a very good efficiency from the aerosol. In addition, we listed some

307

typical existing methods for spore-aerosol collection, shown in Table S1. Compared with these

308

methods, our enrichment chip provided a relatively shorter sampling time.

309

Validation of the spore-aerosol detection system. Our system provided quantitative analyses of

310

spores by using a detection chip to evaluate collected spores from the upstream enrichment chip.

311

The feasibility of the detection chip was validated by testing A. niger spore suspension containing

312

~500 cells. Figure 5A-a showed the image of reaction channel under bright field. The


Page 16 of 33

Page 17 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

313

microspheres formed a monolayer in the 100-µm wide reaction channel, which facilitated the

314

result reading due to all microspheres could be seen under the same microscopic vision field.

315

Figure 5A-b and Figure 5A-c showed the positive result and negative result, respectively, under

316

490 nm extraction. The green fluorescence presenting in the positive result demonstrated that the

317

immunoassay could analyze the amount of spores in the reaction channel. The negative result

318

indicated the monolayer of microspheres could provide a clean background for the immunoassay.

319

To realize quantitative analyses of A. niger spores, the standard curve was established between

320

spore count and fluorescence density. The spore suspensions containing 1000, 750, 500, 200, 100,

321

50, 20, and 10 cells, respectively, were tested on the detection chip as samples. The fluorescence

322

image of each sample was shown in Figure 6A. The fluorescence density of sample containing

323

1000 spores was largest among all samples and it decreased as spore number decreased in samples

324

(as shown in Figure 6B). The detection limit of the chip was 20 spores, equivalent to ~300

325

spores·m−3 that could be detected by 60-min sampling using the enrichment chip. A fitting formula

326

with good R-squared (> 0.90) was established from the standard curve, which would be

327

convenient to the quantitative analysis. In addition, we found that when the number of spores in

328

sample was larger than 500, the spores could be easily intercepted and deposited at the front of

329

microsphere channel, which facilitate the chip to capture large amounts of spores avoiding the

330

escape of target spores. Generally, the concentration of spores in the indoor air was at the range of

331

50 to × 103 CFU·m−3 changing with seasons3. As reported in some researches, the outbreak growth

332

of fungi could release a high concentration of spores, approximately 104 CFU·m−3 10,25,52. These

333

results indicated that our system is feasible to handle the samples from common indoor air.


ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

334 335

Figure 5. (A) Validation of the feasibility of the detection chip, (a) Bright-field image of reaction

336

channel packed with microspheres, (b) Fluorescence image of reaction channel for detection of

337

500 spores, (c) Fluorescence image of reaction channel for detection of 0 spores as a blank. (B)

338

Optical density comparison of immunofluorescence detections of 500 spores (b) and 0 spores as a

339

blank (c). Values are the mean ± s.d. for n = 3, **p < 0.01.


Page 18 of 33

Page 19 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

340 341

Figure 6. (A) Fluorescence images of reaction channels for detection of 10, 20, 50, 100, 200, 500,

342

750, and 1000 of A. niger spores, respectively. (B) Standard curve for evaluation of spore count in

343

reaction channel via optical density of fluorescence. Standard deviations for n = 3.

344

To further test specificity of the proposed system, A. oryzae spore was used as interferent

345

component mixed with A. niger samples in spore-aerosol generations. The A. oryzae spore was

346

chosen as the interferent because its diameter is similar to that of A. niger spore which makes it

347

can be physically captured by the enrichment chip. In addition, these two kinds of Aspergillus

348

spores are hard to be distinguished under the bright-field microscope. It is a good example to test

349

the specificity of the proposed system. The spore mixtures containing 25 %, 75%, and 100% of A.

350

niger spores were aerosolized into the generation cube following the aerosol generation

351

procedures above, respectively. For 5 min sampling by the enrichment chip, the collected spores


ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

352

were eluted with PBS and then analyzed on the detection chip. The fluorescence images of each

353

sample was shown in Figure 7A. The fluorescence density of sample containing 75% A. niger

354

spores was 2.31 times higher than that of sample containing 25% A. niger spores (as shown in

355

Figure 7B). The results demonstrated our detection chip could distinguish the specific pathogenic

356

spores from other species with good specificity. Furthermore, we calculated the number of A.

357

niger spores in each sample (as Table S3-5 shown) by converting fluorescence density to spore

358

quantity using the fitting formula. The data of estimated spore-aerosol concentration could match

359

with the data from APS. The actual samples with unknown concentrations also be detected

360

through the proposed system and traditional sedimentation method (shown in Table S6). Therefore,

361

the proposed system has the capability for quantitative analysis of specific pathogenic spores

362

directly from the air. Furthermore, the spore analysis in this system took relative less time

363

compared with other methods in Table S2. Its detection limit might be not as low as those highly

364

sensitive method such as biosensors30,31 and qPCR28, however, the sensitivity of our system used

365

for the forewarning of airborne spores in air could fulfill practical detection, since the fungal

366

spores usually threaten human health under a relative high concentration.


Page 20 of 33

Page 21 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

367 368

Figure 7. (A) Fluorescence images of reaction channels for detection different mixed samples

369

containing A. niger spores and A. oryzae spores, (a) 100% A. niger spores, (b) 75% A. niger spores

370

and 25% A. oryzae spores, (c) 25% A. niger spores and 75% A. oryzae spores. (Total number:

371

~500 spores). (B) Optical density comparison of immunofluorescence detections of 100% A. niger

372

spores (a), 75% A. niger spores and 25% A. oryzae spores (b), 25% A. niger spores and 75% A.

373

oryzae spores (c). Values are the mean ± s.d. for n = 3, **p < 0.01.

374

CONCLUSIONS

375

Herein, we presented a microfluidic platform for direct and precise analysis of specific pathogenic

376

spores from the air. Experimental results demonstrated that the system can be used for enrichment

377

and semi-quantitative detection of airborne Aspergillus niger spores. The elution volume of the

378

upstream enrichment chip is small and can be directly used by the downstream detection chip

379

avoiding secondary condensation. The whole process could be completed within 3 h from spores

380

enrichment to fluorescence analysis on the chip. Moreover, the detection limit of the analysis chip


ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

381

is ~20 spores, equivalent to ~300 spores·m-3 of the concerned targets in air. In addition, the

382

detection chip could be read by a mini fluorescence detector, suitable for point-of-care application.

383

Overall, we believe that the presented system can help to monitor airborne pathogenic spores in

384

the public buildings, public transportations, as well as private places. It also has potential to enable

385

automatic assessment of other specific spore levels in indoor air.

386

ASSOCIATED CONTENT

387

Supporting Information

388

Additional data including the schematic diagram of spore-aerosol generation system, illustration

389

of the system to test the efficiency of the enrichment chip, the comparison of different methods for

390

fungi sampling and detection, the number calculation of A. niger spores in different mixture

391

samples by converting fluorescence density to spore quantity using the fitting formula and actual

392

samples detection by the microfluidic system are given in the Supporting Information.

393

AUTHOR INFORMATION

394

Corresponding Author

395

* E-mail: [email protected] (G.S.)

396

Notes

397

The authors declare no competing financial interest.

398

Acknowledgments

399

This work was supported by National Natural Science Foundation of China (21577019, 21527814,


Page 22 of 33

Page 23 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

400

21377026), the National Key Research and Development Program of China (2016YFD0500604),

401

the

402

(No.17JC1401001).

Program

of

Science

and

Technology

Commission

403 404 405 406 407 408 409 410


of

Shanghai

Municipality

ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

411

Page 24 of 33

REFERENCES

412

(1) Kuhn, D. M.; Ghannoum, M. A. Indoor mold, toxigenic fungi, and

413

Stachybotrys chartarum: infectious disease perspective. Clin. Microbiol. Rev.

414

2003, 2003 16 (1), 144-172.

415 416

(2) HA, B. An update on pollen and fungal spore aerobiology. J. Allergy

Clin. Immunol. 2002, 2002 110 (4), 544-552.

417

(3) Salonen, H.; Duchaine, C.; Mazaheri, M.; Clifford, S.; Lappalainen, S.;

418

Reijula, K.; Morawska, L. Airborne viable fungi in school environments in

419

different climatic regions – A review. Atmos. Environ. 2015, 2015 104, 186-194.

420

(4) Mendell, M. J.; Kumagai, K. Observation‐based metrics for residential

421

dampness and mold with dose‐response relationships to health: a review.

422

Indoor Air 2016, 2016 27 (3), 506-517.

423 424

(5) Hendry, K. M.; Cole, E. C. A review of mycotoxins in indoor air. J.

Toxicol. Environ. Health 1993, 1993 38 (2), 183-198.

425

(6) Miller, J. D.; Mcmullin, D. R. Fungal secondary metabolites as harmful

426

indoor air contaminants: 10 years on. Appl. Microbiol. Biotechnol. 2014, 2014 98

427

(24), 9953-9966.

428

(7) Mendell, M. J.; Mirer, A. G.; Cheung, K.; Tong, M.; Douwes, J.

429

Respiratory

430

Dampness-Related Agents: A Review of the Epidemiologic Evidence. Environ

431

Health Perspect 2011, 2011 119 (6), 748-756.

432

and

Allergic

Health

Effects

of

Dampness,

Mold,

and

(8) Portnoy, J. M.; Kwak, K.; Dowling, P.; Vanosdol, T.; Barnes, C. Health


Page 25 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

433

effect of indoor fungi. Ann. Allergy, Asthma Immunol. 2005, 2005 94 (3), 313-320.

434

(9) Mitchell, C. S.; Zhang, J. J.; Sigsgaard, T.; Jantunen, M.; Lioy, P. J.;

435

Samson, R.; Karol, M. H. Current state of the science: health effects and

436

indoor environmental quality. Environ. Health Perspect. 2007, 2007 115 (6),

437

958-964.

438

(10)

Srikanth, P.; Sudharsanam, S.; Steinberg, R. Bio-aerosols in

439

indoor environment: composition, health effects and analysis. Indian J. Med.

440

Microbiol. 2008, 2008 26 (4), 302-312.

441

(11)

Garvey, G. S.; Keller, N. P. Fungal Secondary Metabolites and

442

Their Fundamental Roles in Human Mycoses. Current Fungal Infection

443

Reports 2010, 2010 4 (4), 256-265.

444

(12)

Egbuta, M. A.; Mwanza, M.; Babalola, O. O. Health Risks

445

Associated with Exposure to Filamentous Fungi. Int. J. Environ. Res. Public

446

Health 2017, 2017 14 (7), 719, DOI:710.3390/ijerph14070719.

447

(13)

Katsurayama, A. M.; Taniwaki, M. H. Fungi and aflatoxins in rice:

448

occurrence and significance to consumer health. Braz. J. Food. Technol. 2017, 2017

449

20, http://dx.doi.org/10.1590/1981-6723.0617.

450

(14)

Schoch-Spana, M.; Cicero, A.; Adalja, A.; Gronvall, G.; Kirk Sell, T.;

451

Meyer, D.; Nuzzo, J. B.; Ravi, S.; Shearer, M. P.; Toner, E. Global catastrophic

452

biological risks: toward a working definition. Health Secur. 2017, 2017 15 (4),

453

323-328.

454

(15)

Metcalf, S. C.; Dockrell, D. H. Improved outcomes associated with


ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

455

advances in therapy for invasive fungal infections in immunocompromised

456

hosts. J Infect 2007, 2007 55 (4), 287-299.

457

(16)

Ascioglu, S.; Rex, J. H.; Pauw, B. D.; Bennett, J. E.; Bille, J.;

458

Crokaert, F.; Denning, D. W.; Donnelly, J. P.; Edwards, J. E.; Erjavec, Z.

459

Defining Opportunistic Invasive Fungal Infections in Immunocompromised

460

Patients with Cancer and Hematopoietic Stem Cell Transplants: An

461

International Consensus. Clin. Infect. Dis. 2002, 2002 34 (1), 7-14.

462

(17)

Candoni, A.; Mestroni, R.; Damiani, D.; Tiribelli, M.; Michelutti, A.;

463

Silvestri, F.; Castelli, M.; Viale, P.; Fanin, R. Caspofungin as first line therapy

464

of pulmonary invasive fungal infections in 32 immunocompromised patients

465

with hematologic malignancies. Eur. J. Haematol. 2015, 2015 75 (3), 227-233.

466

(18)

Dornbusch, H. J. G., A.; Walsh, T. J. . REVIEW: Diagnosis of

467

invasive fungal infections in immunocompromised children. Clin. Microbiol.

468

Infect. 2010, 2010 16 (9), 1328–1334.

469

(19)

Kontoyiannis, D. P.; Marr, K. A.; Park, B. J.; Alexander, B. D.;

470

Anaissie, E. J.; Walsh, T. J.; Ito, J.; Andes, D. R.; Baddley, J. W.; Brown, J. M.

471

Prospective surveillance for invasive fungal infections in hematopoietic stem

472

cell transplant recipients, 2001-2006: overview of the Transplant-Associated

473

Infection Surveillance Network (TRANSNET) Database. Clin. Infect. Dis. 2010, 2010

474

50 (8), 1091-1100.

475 476

(20)

Luce, J. M.; Ostenson, R. C.; Springmeyer, S. C.; Hudson, L. D.

Invasive Aspergillosis Presenting as Pericarditis and Cardiac Tamponade.


Page 26 of 33

Page 27 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

477 478

Chest 1979, 1979 76 (6), 703-705. (21)

Schuster, E.; Dunn-Coleman, N.; Frisvad, J. C. On the safety of

479

Aspergillus niger--a review. Appl. Microbiol. Biotechnol. 2002, 2002 59 (4-5),

480

426-435.

481

(22)

Bernstein, J. A.; Levin, L.; Crandall, M. S.; Perez, A.; Lanphear, B.

482

A pilot study to investigate the effects of combined dehumidification and HEPA

483

filtration on dew point and airborne mold spore counts in day care centers.

484

Indoor Air 2010, 2010 15 (6), 402-407.

485

(23)

Fahlbusch, B.; Hornung, D.; Heinrich, J.; Jäger, L. Predictors of

486

group 5 grass‐pollen allergens in settled house dust: comparison between

487

pollination and nonpollination seasons. Allergy 2015, 2015 56 (11), 1081-1086.

488

(24)

Cabana, H.; Jones, J. P.; Agathos, S. N. Elimination of Endocrine

489

Disrupting Chemicals using White Rot Fungi and their Lignin Modifying

490

Enzymes: A Review. Eng. Life Sci. 2010, 2010 7 (5), 429-456.

491 492 493

(25)

Prussin, A. J.; Marr, L. C. Sources of airborne microorganisms in

the built environment. Microbiome 2015, 2015 3 (1), 78. (26)

Amend, A. S.; Seifert, K. A.; Samson, R.; Bruns, T. D. Indoor

494

fungal composition is geographically patterned and more diverse in temperate

495

zones than in the tropics. Proc. Natl. Acad. Sci. 2010, 2010 107 (31), 13748-13753.

496

(27)

Kostov, K.; Verstappen, E.; Bergervoet, J.; Weerdt, M.; Schoen, C.;

497

Slavov, S.; Bonants, P. Multiplex detection and identification of Phytophthora

498

spp. using target‐specific primer extension and Luminex xTAG technology.


ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

499 500

Plant Pathol. 2016, 2016 65 (6), 1008-1021. (28)

Emerson, J. B.; Keady, P. B.; Brewer, T. E.; Clements, N.; Morgan,

501

E. E.; Awerbuch, J.; Miller, S. L.; Fierer, N. Impacts of flood damage on

502

airborne bacteria and fungi in homes after the 2013 Colorado Front Range

503

flood. Environ. Sci. Technol. 2015, 2015 49 (5), 2675-2684.

504

(29)

Qian, J.; Hospodsky, D.; Yamamoto, N.; Nazaroff, W. W.; Peccia,

505

J. Size‐resolved emission rates of airborne bacteria and fungi in an occupied

506

classroom. Indoor Air 2012, 2012 22 (4), 339-351.

507

(30)

Nugaeva, N.; Gfeller, K. Y.; Backmann, N.; Düggelin, M.; Lang, H.

508

P.; Güntherodt, H.-J.; Hegner, M. An antibody-sensitized microfabricated

509

cantilever for the growth detection of Aspergillus niger spores. Microsc.

510

Microanal. 2007, 2007 13 (1), 13-17.

511

(31)

Jin, J.-H.; Kim, J.; Jeon, T.; Shin, S.-K.; Sohn, J.-R.; Yi, H.; Lee, B.

512

Y. Real-time selective monitoring of allergenic Aspergillus molds using

513

pentameric antibody-immobilized single-walled carbon nanotube-field effect

514

transistors. RSC Adv. 2015, 2015 5 (20), 15728-15735.

515

(32)

Jing, W.; Zhao, W.; Liu, S.; Li, L.; Tsai, C.-T.; Fan, X.; Wu, W.; Li,

516

J.; Yang, X.; Sui, G. Microfluidic device for efficient airborne bacteria capture

517

and enrichment. Anal. Chem. 2013, 2013 85 (10), 5255-5262.

518

(33)

Bian, X.; Lan, Y.; Wang, B.; Zhang, Y. S.; Liu, B.; Yang, P.; Zhang,

519

W.; Qiao, L. Microfluidic Air Sampler for Highly Efficient Bacterial Aerosol

520

Collection and Identification. Anal. Chem. 2016, 2016 88 (23), 11504-11512.


Page 28 of 33

Page 29 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

521

(34)

Jing, W.; Jiang, X.; Zhao, W.; Liu, S.; Cheng, X.; Sui, G.

522

Microfluidic platform for direct capture and analysis of airborne Mycobacterium

523

tuberculosis. Anal. Chem. 2014, 2014 86 (12), 5815-5821.

524

(35)

Lee, J.; Jeong, K.; Hashimoto, M.; Kwon, A.; Rwei, A. Synthetic

525

ligand-coated magnetic nanoparticles for microfluidic bacterial separation from

526

blood. Nano Lett. 2013, 2013 14 (1), 1-5.

527

(36)

Duquenne, P.; Simon, X.; Koehler, V.; Goncalves-Machado, S.;

528

Greff, G.; Nicot, T.; Poirot, P. Documentation of bioaerosol concentrations in

529

an indoor composting facility in France. J. Environ. Monit. 2012, 2012 14 (2),

530

409-419.

531

(37)

Aliabadi, A. A.; Rogak, S. N.; Bartlett, K. H.; Green, S. I.

532

Preventing Airborne Disease Transmission: Review of Methods for Ventilation

533

Design in Health Care Facilities. Adv. Prev. Med. 2014, 2014 2011 (1-2), 124064.

534

(38)

Amann, R.; Gloëckner, F.-O.; Neef, A. Modern methods in

535

subsurface microbiology: in situ identification of microorganisms with nucleic

536

acid probes. FEMS Microbiol. Rev. 1997, 1997 20 (3-4), 191-200.

537

(39)

Cupples, A. M. The use of nucleic acid based stable isotope

538

probing to identify the microorganisms responsible for anaerobic benzene and

539

toluene biodegradation. J. Microbiol. Methods 2011, 2011 85 (2), 83-91.

540

(40)

Gerda, H.; Alice, C. L.; Hebe, M. D.; Igrid, R. G.; Victoria, M. G.;

541

Shawn, A. H.; Kevin, G. R.; Gary, S. S. Real-Time PCR Quantification of

542

Nitrifying Bacteria in a Municipal Wastewater Treatment Plant. Environ. Sci.


ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

543 544

Technol. 2017, 2017 37 (2), 343-351. (41)

Yamamoto, N.; Matsuzaka, Y.; Kimura, M.; Matsuki, H.;

545

Yanagisawa, Y. Comparison of dry-and wet-based fine bead homogenizations

546

to extract DNA from fungal spores. J. Biosci. Bioeng. 2009, 2009 107 (4), 464-470.

547

(42)

Yang, W. J.; Chen, J. H.; Chen, G. N.; Wang, S. H.; Fu, F. F. The

548

early diagnosis and fast detection of blast fungus, Magnaporthe grisea , in rice

549

plant by using its chitinase as biochemical marker and a rice cDNA encoding

550

mannose-binding lectin as recognition probe. Biosens. Bioelectron. 2013, 2013 41

551

(6), 820-826.

552

(43)

Teste, B.; Kanoufi, F.; Descroix, S.; Poncet, P.; Georgelin, T.;

553

Siaugue, J.-M.; Petr, J.; Varenne, A.; Hennion, M.-C. Kinetic analyses and

554

performance of a colloidal magnetic nanoparticle based immunoassay

555

dedicated to allergy diagnosis. Anal. Bioanal. Chem. 2011, 2011 400 (10),

556

3395-3407.

557

(44)

Wang, S.; Liu, K.; Liu, J.; Yu, Z. T. F.; Xu, X.; Zhao, L.; Lee, T.; Lee,

558

E. K.; Reiss, J.; Lee, Y. K. Highly efficient capture of circulating tumor cells by

559

using nanostructured silicon substrates with integrated chaotic micromixers.

560

Angew. Chem. 2011, 2011 123 (13), 3140-3144.

561

(45)

Wang, Y.-C.; Han, J. Pre-binding dynamic range and sensitivity

562

enhancement for immuno-sensors using nanofluidic preconcentrator. Lab Chip

563

2008, 2008 8 (3), 392-394.

564

(46)

Hsieh, M.-C.; Chiu, Y.-H.; Lin, S.-F.; Chang, J.-Y.; Chang, C.-O.;


Page 30 of 33

Page 31 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

565

Chiang, H. K. Amplification of the signal intensity of fluorescence-based

566

fiber-optic biosensors using a Fabry-Perot resonator structure. Sens. 2015, 2015 15

567

(2), 3565-3574.

568

(47)

Deng, G.; Xu, K.; Sun, Y.; Chen, Y.; Zheng, T.; Li, J. High

569

Sensitive Immunoassay for Multiplex Mycotoxin Detection with Photonic

570

Crystal Microsphere Suspension Array. Anal. Chem. 2013, 2013 85 (5), 2833-2840.

571

(48)

Zheng, Y.; Yao, M. Liquid impinger BioSampler's performance for

572

size-resolved viable bioaerosol particles. J. Aerosol Sci. 2017, 2017 106 (2017),

573

34-42.

574

(49)

Kesavan, J.; Humphreys, P.; Nasr, B.; Ahmadi, G.; Knox, C. K.;

575

Valdes, E.; Rastogi, V.; Dhaniyala, S. Experimental and computational study of

576

reaerosolization of 1 to 5 Î¼m PSL microspheres using jet impingement.

577

Aerosol Sci. Technol. 2016, 2016 51 (3), 377-387.

578

(50)

Wang, F.; Dijksterhuis, J.; Wyatt, T.; Han, A. B. W.; Bleichrodt, R. J.

579

VeA of Aspergillus niger increases spore dispersing capacity by impacting

580

conidiophore architecture. Antonie Van Leeuwenhoek 2015, 2015 107 (1), 187-199.

581

(51)

Ma, X.; Ma, P.; Zhang, D.; Hua, J.; Zhang, C.; Huang, T.; Wang, J.;

582

Niu, J. A novel sandwich-type tungstoarsenate containing a cagelike {Ca6}

583

cluster with a water molecule enwrapped. Dalton Trans. 2013, 2013 42 (4), 874-878.

584

(52)

Cabral, J. P. Can we use indoor fungi as bioindicators of indoor air

585

quality? Historical perspectives and open questions. Sci. Total Environ. 2010, 2010

586

408 (20), 4285-4295.


ACS Sensors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

587

588 589 590


Page 32 of 33

Page 33 of 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sensors

591

For TOC only

592


Microfluidic System for Rapid Detection of Airborne Pathogenic Fungal

Recommend Documents