Microplastic abundance and composition in western Lake Superior as

2 days ago - Microscopy, Pyrolysis-Gas Chromatography/Mass spectrometry (Pyr-GC/MS), and Fourier Transform Infrared spectroscopy (FTIR) were used to q...
4 downloads 14 Views 2MB Size
Subscriber access provided by READING UNIV

Article

Microplastic abundance and composition in western Lake Superior as determined via microscopy, Pyr-GC/MS, and FTIR. Erik Hendrickson, Elizabeth C. Minor, and Kathryn Schreiner Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.7b05829 • Publication Date (Web): 18 Jan 2018 Downloaded from http://pubs.acs.org on January 18, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 35

Environmental Science & Technology

1 2

Microplastic abundance and composition in western Lake Superior as determined via microscopy, Pyr-GC/MS, and FTIR.

3

Erik Hendrickson1, Elizabeth C. Minor2*, and Kathryn Schreiner3 1

4 5 6 7 8 9 10 11

Water Resources Science Program, University of Minnesota, 2205 East 5th St, Duluth, MN 55812. E-mail; [email protected]

2

Large Lakes Observatory and Department of Chemistry and Biochemistry, University of Minnesota Duluth, 2205 East 5th St. Duluth, MN 55812. Email: [email protected] 3

Large Lakes Observatory and Department of Chemistry and Biochemistry, University of Minnesota Duluth, 2205 East 5th St. Duluth, MN 55812. Email: [email protected] *corresponding author For submission to Environmental Science and Technology

12

ACS Paragon Plus Environment

Environmental Science & Technology

13

14

Page 2 of 35

Abstract: While plastic pollution in marine and freshwater systems is an active area of

15

research, there is not yet an in-depth understanding of the distributions, chemical

16

compositions, and fates of plastics in aquatic environments. In this study, the magnitude,

17

distribution, and common polymers of microplastic pollution in surface waters in

18

western Lake Superior are determined. Analytical methodology, including estimates of

19

ambient contamination during sample collection and processing, are described and

20

employed. Microscopy, Pyrolysis-Gas Chromatography/Mass spectrometry (Pyr-

21

GC/MS), and Fourier Transform Infrared spectroscopy (FTIR) were used to quantify and

22

identify microplastic particles. In surface waters, fibers were the most frequently

23

observed morphology, and, based upon PyGC/MS analysis, PVC was the most frequently

24

observed polymer, followed by polypropylene and polyethylene. The most common

25

polymer identified by FTIR was polyethylene. Despite the low human population in Lake

26

Superior’s watershed, microplastic particles (particularly fibers, fragments, and films)

27

were identified in western-lake surface waters at levels comparable to average values

28

reported in studies within Lake Michigan, the North Atlantic Ocean, and the South

29

Pacific Ocean. This study provides insight to the magnitude of microplastic pollution in

30

western Lake Superior, and describes in detail methodology to improve future

31

microplastics studies in aquatic systems.

32 33 34 35

Introduction: Since the advent of mass-produced plastic in the middle of the 20th century, plastic pollution has become a significant environmental concern and a focus of recent 2

ACS Paragon Plus Environment

Page 3 of 35

Environmental Science & Technology

36

study and remediation efforts in aquatic systems. Input vectors of plastic pollution to

37

aquatic systems include wastewater treatment plants, shoreline debris, river outflows,

38

landfills, industrial pollution, illegal dumping into aquatic systems, and atmospheric

39

deposition.1–4

40

Most plastic particles in oceanic gyres are less than 10 mm in length,5,6 which

41

encompasses part of the mesoplastic size range as well as microplastic size range.4

42

Historically, “microplastic” particles have been inconsistently defined in terms of size.7

43

The definition established for the this study, defined by the National Oceanographic and

44

Atmospheric Administration (NOAA), is a particle greater than 333 µm (as set by the

45

plankton net used for collection) with no dimension longer than 5.0 mm.8,9 Microplastic

46

particles have several recognized morphologies, including beads, foams, films,

47

fragments, fibers, and other shapes resulting from the degradation of larger plastics.1,4,10,11

48

Negative or potentially negative effects of microplastic pollution can include

49

physical damage to organisms upon ingestion, false satiation, toxicological effects from

50

adsorbed substances, speculated toxicity from polymers and additives, and providing a

51

vector for invasive species.11–13 Much of the focus on potential toxicological damage

52

from microplastic pollution regards hydrophobic substances adsorbing to microplastic

53

particles, including PCBs (polychlorinated biphenyls), DDT

54

(dichlorodiphenyltrichloroethane) related compounds, and PAHs (polyaromatic

55

hydrocarbons),12 although the potential amount of uptake of these adsorbed substances

56

from hydrophobic microplastic surfaces into organism biomass is not well known. Recent

57

research has revealed the presence of inorganic contaminants in microplastic paint

3

ACS Paragon Plus Environment

Environmental Science & Technology

58

pigments as well, including copper (Cu), lead (Pb), and cadmium (Cd),14 and the uptake

59

of these pigment-related inorganic contaminants into aquatic organisms is unknown.

60

Much of the research regarding microplastic pollution has focused on marine

Page 4 of 35

61

systems with less research in freshwater systems.11,12 Recently, however, there has been

62

an increasing interest in studying microplastics in freshwater systems, including

63

investigations of lakes in Italy, Switzerland, Mongolia, East Africa, Canada, and the

64

United States.15–24 Previous studies in the Laurentian Great Lakes have shown that

65

microplastic pollution has a propensity to be elevated in surface waters in nearshore

66

areas, especially near areas of high human population density and industrial activity,

67

where extensive clean-up projects have not been performed.1,18,25 These studies have

68

found that average open-water plastic densities resembled those in severely polluted

69

ocean gyres1,18 and plastic was often found to be greater than 80% of anthropogenic

70

shoreline debris items.1 As with surface water studies, investigations of microplastics in

71

benthic settings have typically been in marine environments,23 although a study on Lake

72

Ontario sediments, as well as sediments from affiliated tributaries and beaches, was

73

conducted in 2016, revealing elevated concentrations in sediments near or in Humber

74

Bay and Toronto Harbor.24

75

Despite Lake Superior’s status as the largest freshwater lake on earth by area,

76

there is a lack of data, quantitatively and qualitatively, regarding microplastic pollution in

77

this Laurentian Great Lake. Existing published data is from single measurements at five

78

stations in the relatively unpopulated eastern basin of Superior and two tributaries

79

flowing into the lake.18,26

4

ACS Paragon Plus Environment

Page 5 of 35

Environmental Science & Technology

80

Quantification of microplastic particles often relies on visual sorting from a

81

processed sample and recording the number of particles observed.4 For reporting

82

microplastic quantities in the environment, typical units are simply a count of plastic

83

items per unit area or volume, i.e. “items per km2” or “items per m3”, although, some

84

previous studies have used mass per mass units as well.10,27–29 Pyrolysis-Gas

85

Chromatography/Mass Spectrometry (Pyr-GC/MS), Fourier Transform Infrared

86

Spectroscopy (FTIR), Focal-Plane Array (FPA) FTIR, Raman spectroscopy, and

87

Scanning Electron Microscopy (SEM) are qualitative techniques used for identifying and

88

characterizing microplastic polymers.4,10,30,31 These techniques are typically used after

89

isolating microplastic particles via a density separation procedure. Density separations

90

are conducted by subjecting environmental samples to concentrated or saturated salt

91

solutions, followed by filtration or other separation techniques, and then optical

92

identification/selection of microplastic particles.4,10,12,30,32

93

The goals for the present study are to quantify the distribution of microplastic

94

pollution in surface waters of western Lake Superior, to identify polymers present in

95

microplastic debris, and to improve methods for the quantification and identification of

96

microplastics in aquatic environments. Little quantitative data exists for the extent of

97

microplastic pollution in Lake Superior, and no published data exists for far western Lake

98

Superior. Western Lake Superior is a high stress region of the lake33,34 impacted by the

99

most populated (110,000 people) and most densely populated urban area (1100 people

100

per square mile) of Lake Superior: Duluth, Minnesota and Superior, Wisconsin (as of the

101

2016 censuses for the United States and Canada).35,36

5

ACS Paragon Plus Environment

Environmental Science & Technology

102

In addition, the polymer composition of Lake Superior microplastics has not yet

103

been investigated. In this study, we apply Pyr-GC/MS and ATR-FTIR for qualitative

104

compositional characterization. These two techniques provide different but

105

complementary interrogations of sample composition. Pyr-GC/MS uses pyrolysis to

106

break polymers into smaller moieties, of which the volatile pieces are then separated and

107

identified using GC-MS. In ATR-FTIR the molecular vibrations of transiently polar

108

covalent bonds are measured, through the change they impart to an evanescent wave

109

penetrating the sample.

110

Page 6 of 35

Furthermore, previously established methods have been criticized for having a

111

lack of “clean techniques”.37 While a number of investigations of aquatic microplastic

112

pollution have taken place, various publications provide detailed critiques of the

113

commonly used and published methods. These methods have been plagued by variable

114

sample contamination during sampling and processing, difficulty distinguishing among

115

natural materials and microplastics, bias associated with not selecting small and

116

uncolored particles, and inefficient isolation of denser plastics unless heavier and

117

expensive salts like NaI, ZnCl2, and polytungstates are used in density

118

separations.4,25,31,32, 37, 38 Here, we attempt to address some of these analytical issues.

119

“Clean” analytical techniques are employed, including washing sampling gear

120

methodically between samples, collecting ambient (field) controls, collecting sample

121

processing method blanks, and using lab control samples (LCS) of analytical plastic

122

standards to assess the efficiency of our techniques in isolating microplastics.37,39

123 124

Methods: 6

ACS Paragon Plus Environment

Page 7 of 35

Environmental Science & Technology

125

Methodology Motivation and Influence:

126

Methods used here for sampling, sample processing, and analysis were strongly

127

influenced by previous works, in particular NOAA’s publication regarding standardized

128

microplastic sampling and sample processing by Masura and colleagues.8 Microplastic

129

polymers identified included polyethylene (PE), polypropylene (PP), polyvinylchloride

130

(PVC), polystyrene (PS), and polyethylene terephthalate (PET). These polymers were

131

chosen because they are the most commonly produced and encountered in the

132

environment.7,25 These polymers correspond with designator codes 1-6 created by the

133

Society of The Plastics Industry (SPI) and currently used by the American Society for

134

Testing and Materials (ASTM).4 While these polymers were the primary references for

135

analysis (see Table S-1 for further details), other polymers isolated, analyzed, and

136

identified were reported as well.

137

Microplastic particles were defined as belonging to one of 6 morphological

138

categories (shown in Figure 1, see also SI, Table S-2), similar to those defined by

139

Crawford and Quinn.4 Note that while the effective upper-limit based upon sieving is that

140

at least 2 dimensions were less than 4.0 mm, any non-fibrous particles with a dimension

141

of 4.0 to 5.0 mm that passed through the 4.0 mm sieve, and were captured on the 250 µm

142

sieve, were isolated during microscopy and included in subsequent analyses. Non-fibrous

143

particles determined by microscopy to exceed 5.0 mm in any dimension were not counted

144

as microplastic particles. Despite the use of a 250 µm sieve, the effective minimum sizes

145

of microplastic particles collected was 333 µm as established by the mesh size of the

146

manta net (see below).

147 7

ACS Paragon Plus Environment

Environmental Science & Technology

148

Page 8 of 35

Water Sampling:

149

Twelve sample sites in western Lake Superior were chosen to include key

150

environments speculated to differ in their microplastic distributions based upon proximity

151

to believed sources (local wastewater treatment plant, urban shorelines, and river

152

outflows). These sites were categorized into generalized, regional environments:

153

nearshore, estuary/harbor, and offshore/open water (Figure S-1 and Table S-3).

154

An NQS-45-60 manta tow net (333 µm mesh size, 3 m length, frame opening 14

155

cm deep by 85 cm wide, Ocean Instruments, San Diego, CA, USA) was used for surface

156

water sampling. At each sample site, a target tow length of 500 to 2000 m was

157

established with length based upon the amount of floating debris. The distance sampled

158

was measured using a Model 2030R flowmeter (General Oceanics Inc., Miami, FL,

159

USA). To avoid sample contamination, the manta net and collection vessel were rinsed

160

thoroughly before each tow. The net was rinsed in surface water without the collection

161

vessel in place, and then was thoroughly rinsed from the outside using an on-vessel lake

162

water hose to prevent sample contamination. Finally, the collection vessel was tripled-

163

rinsed using Millipore water before attaching to the net and beginning a tow.

164

After a tow was completed, the net was rinsed thoroughly from the outside using

165

the on-vessel hose to concentrate collected materials into the collection vessel. Contents

166

captured in the collection vessel were quantitatively transferred to 4.0 mm and 250 µm

167

metal sieves in series. Materials were hand-shaken on the sieves and washed with

168

Millipore water until it was visually apparent that only collected materials larger than 4.0

169

mm were present. Contents isolated on each sieve were transferred via forceps and/or

170

water rinses (either Millipore water or