Molecularly Imprinted

Jan 12, 2017 - *(J.W.) Phone: +86 10-68984545. ... Under optimum conditions, the detection limit of this system was 40.7 μg L–1, and a linear range...
1 downloads 3 Views 1MB Size
Subscriber access provided by UNIV OF CALIFORNIA SAN DIEGO LIBRARIES

Article

Core–Shell Metal–Organic Frameworks/Molecularly Imprinted Nanoparticles as Absorbents for the Detection of Pyrraline in Milk and Milk Powder Huilin Liu, Lin Mu, Xiaomo Chen, Jing Wang, Shuo Wang, and Baoguo Sun J. Agric. Food Chem., Just Accepted Manuscript • DOI: 10.1021/acs.jafc.6b05429 • Publication Date (Web): 12 Jan 2017 Downloaded from http://pubs.acs.org on January 14, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Journal of Agricultural and Food Chemistry is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 32

Journal of Agricultural and Food Chemistry

1

Core–Shell

2

Nanoparticles as Absorbents for the Detection of Pyrraline in Milk and

3

Milk Powder

4

Huilin Liu1, Lin Mu1, Xiaomo Chen1, Jing Wang1,* Shuo Wang1,2 and Baoguo

5

Sun1

6

1

7

and Business University (BTBU), 11 Fucheng Road, Beijing, 100048, China.

8

2

9

University of Science and Technology, Tianjin, 300457, China.

10

Metal–Organic

Frameworks/Molecularly

Beijing Engineering and Technology Research Center of Food Additives, Beijing Technology

Key Laboratory of Food Nutrition and Safety, Ministry of Education of China, Tianjin

*Corresponding author: Jing Wang

11

Tel: (86 10) 68984545;

12

Fax: (86 10) 68985456;

13

Imprinted

Email: [email protected]

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

14

Abstract

15

A novel core–shell metal–organic framework coated with a dummy template molecularly

16

imprinted polymer (MOF@DMIP) was synthesized by one-pot bulk polymerization for the detection

17

of pyrraline in food samples. The pyrraline analog pyrrolidine-3-carboxylic acid was used as the

18

template because of its lower cost, and MIL-101 was used as the MOF core owing to its numerous

19

inherent advantages, including high chemical and hydrothermal stability. MIL-101@DMIP was used

20

to detect trace pyrraline in foods by solid-phase extraction combined with high performance liquid

21

chromatography. It exhibited the advantages of faster mass transport, excellent sensitivity and

22

selectivity. Under optimum conditions, the detection limit of this system was 40.7 µg L-1, and a

23

linear range was from 5×10−7 to 2×10−3 mol L−1, within relative standard deviations of 4.46%–6.87%.

24

The recoveries ranged from 92.23%-103.87%, indicating the excellent ability of the prepared MIL-

25

101@DMIP to recognize pyrraline in complex food matrices, and its potential for application in

26

pyrraline detection.

27

Keywords: Advanced glycation end products; pyrraline; mental–organic frameworks; molecular

28

imprinted polymer; solid-phase extraction; HPLC

ACS Paragon Plus Environment

Page 2 of 32

Page 3 of 32

29

Journal of Agricultural and Food Chemistry

Introduction

30

Advanced glycation end-products (AGEs) have been studied extensively since they were first

31

proposed by Brownlee in 1984.1 AGEs are a set of stable end products formed through advanced

32

Maillard reactions, and include pyrraline, pentosidine, crossline, carboxymethyl-lysine and others.2

33

According to histopathological studies, AGEs accumulate in different tissues and organs of the

34

human body and play a significant role in aging and the development of other chronic diseases, such

35

as diabetic nephropathy, Alzheimer’s disease, and atherosclerosis.3-5 Pyrraline (2-amino-6-(2-formyl-

36

5-hydroxymethyl-1-pyrrolyl)-hexanoic acid), one of the AGEs, was first identified and described by

37

Nakayama in 1980.6 Investigators have found that the concentration of pyrraline in the serum of

38

diabetics patients is higher than that in healthy people.7 In addition, immunological studies have

39

shown that pyrraline accumulates in the glomerular basement membrane of patients with

40

atherosclerosis and ultimately leads to kidney failure. As a result, pyrraline has received great

41

attention in recent years both as a potential risk to human health, as well as an important index for

42

quantitative AGEs detection.8 Chromatographic methods have been employed in the detection and

43

measurement of trace pyrraline. Kazuhiro applied the OasisTM HLB solid-phase extraction (SPE)

44

combined with high performance liquid chromatography (HPLC) to monitor urinary pyrraline.9

45

Thomas employed ion-exchange chromatography with a photodiode array for the quantification of

46

pyrraline in model systems.10

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

47

Molecular imprinting technology (MIT) is a discovered method for the detection of target

48

analytes on the molecular level.11,12 The resulting molecularly imprinted polymers (MIPs) are

49

considered to be promising recognition elements with high affinity, selectivity, and stability, and can

50

be used to monitor trace substances in the fields of SPE, chromatographic separation, biological

51

sensors and clinical medicinal analysis.13-15 MIP-based column separation technology have often

52

been applied to separate and enrich the alkaloids, flavones, and polyhydric phenols from traditional

53

Chinese herbs.16 Zhang et al. developed a single-hole hollow molecularly imprinted polymer

54

combined with SPE for the preconcentration of Sudan I dyes in chilli sauce samples.17 Tang et al.

55

employed MIPs and used SPE coupled with HPLC to effectively separate and determine the

56

concentrations of clenbuterol in pork and potable water samples.18 Tan et al. applied molecularly

57

imprinted TiO2 in the discrimination of fruit punch using a fluorescent sensor array for carboxylic

58

acids.19 Zhu et al. prepared MIPs using theanine as a dummy template for the enrichment, and

59

applied them as SPE sorbents in the determination of eighteen amino acids in tobacco.20 MIPs were

60

deposited as thin films on an Au electrode to fabricate an electrochemical chemosensor for the

61

determination of human serum albumin.21 All of these MIPs demonstrated good sensitivity and

62

selectivity towards templates. However, to enhance the efficiency metal-organia frameworks (MOFs)

63

were introduced in the field of MIPs.

64

MOFs have aroused great attention owing to their potential applications in numerous fields.

65

MOFs are porous organic–inorganic materials with a cubic three-dimensional structure, formed by

ACS Paragon Plus Environment

Page 4 of 32

Page 5 of 32

Journal of Agricultural and Food Chemistry

66

linking metal ions to organic bridging ligands.22 Studies have demonstrated that MOFs can be used

67

in gas storage, sensing, drug delivery, separation and catalysis applications because of their good

68

chemical and thermal stabilities and porous nature.23-25 Especially the MOFs was used in the SPE

69

application. Dai et al. employed MIL-101(Cr) as a SPE sorbent for the detection of sulphonamides in

70

water samples combined with UPLC-MS/MS.26 Lv et al. applied MOF-5 as SPE adsorbent coupled

71

with HPLC for the determination of thiol compounds from wastewater.27 Huang et al. introduced

72

MOFs as sorbent for the pre-concentration and enrichment of five organochlorine pesticides from

73

water samples combined with gas chromatography–mass spectrometry.28 Wang et al. applied

74

magnetic graphene@polydopamine@Zr-MOF as the SPE sorbents for the pre-concentration of

75

bisphenols in water samples.29 Ma et al. prepared magnetic MOFs as magnetic SPE adsorbents for

76

the separation of four kinds of pyrazole/pyrrole pesticides in water samples with HPLC.30 Recently,

77

MOFs was also used as the MIP core. Qian et al. firstly prepared a core-shell MIP by coating the

78

MIP shell onto the surface of the MOF, which shows a homogeneous polymer film, cubic shape,

79

thermal stability, and exhibits a higher specific surface area and a faster transfer-mass speed

80

compared with that of the bulk MIP.31 Madiha et al. developed an electrochemical sensor for the

81

detection of tetracycline, based on a gold electrode surface modified with MIP microporous-MOFs.32

82

Zofia et al. prepared a surface MIP film with MOFs. It enlargement increased the analyte

83

accessibility to imprinted molecular cavities.33

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

84

In this study, a strongly binding dummy template MIP (DMIP) was synthesized on the MOF

85

surface using pyrrolidine-3-carboxylic acid (PCC) as the dummy template. The MOF@DMIP was

86

used for the adsorption and enrichment of pyrraline in food samples. Here, MIL-101 was used as the

87

MOF core, owing to its numerous inherent advantages, which includes its high chemical and

88

hydrothermal stability. MIL-101@DMIP exhibited such advantages as faster mass transport

89

excellent sensitivity and selectivity towards targets when compared with traditional MIPs. Finally,

90

we developed the technique of molecularly imprinted solid-phase extraction (MISPE) combined with

91

HPLC for the detection of pyrraline in foods.

92

Materials and Methods

93

Materials and Reagents. All reagents were at least of analytical grade. A pure standard sample

94

of pyrraline was purchased from Toronto Research Chemicals Incorporated (Toronto, Canada).

95

Pseudo-template PCC (95%) was obtained from Tokyo Chemical Industry (Tokyo, Japan). Nε-

96

carboxymethyllysine (CML), 3-pyrroline and pyrrole was purchased from J&K Scientific, Ltd.

97

(Beijing, China). Other chemicals used for the polymer synthesis were (3-aminopropyl)

98

triethoxysilane, (APTES, 98%,; Sinopharm Chemical Reagent Co., Ltd., Beijing, China), tetraethyl

99

orthosilicate (TEOS, 98%,; J&K Scientific, Ltd.), and acetic acid (99.5%, Sinopharm Chemical

100

Reagent Co., Ltd.). Doubly deionized water (18.2 MΩ cm−1) was obtained from a Water Pro water

101

purification system (Labconco, Kansas, MO, USA). Other chemicals used for the MIL-101 synthesis

102

were chromium (III) nitrate nonahydrate (99%, Strem Chemicals, Inc., Massachusetts, USA),

ACS Paragon Plus Environment

Page 6 of 32

Page 7 of 32

Journal of Agricultural and Food Chemistry

103

terephthalic acid (99%, Sinopharm Chemical Reagent Co., Ltd.), hydrofluoric acid (40%, Xilong

104

Chemical Co., Ltd., Guangdong, China). Acetonitrile was of HPLC grade (99.9%, J & K Scientific,

105

Ltd.). Milk and milk powder were provided by the local market.

106

Characterization. Scanning electron microscopy (SEM; S-4800, Hitachi, Japan) was used to

107

observe the surface morphology of MIL-101@DMIP. Fourier transform infrared (FT-IR) spectra

108

(4000–400 cm−1) were recorded for KBr pellets in an FT-IR spectrophotometer (Vertex 70vxrd,

109

Bruker, Germany). X-ray diffraction (XRD) experiments were performed on a D/max-2500

110

diffractometer (Rigaku, Japan) to characterize MIL-101 and MIL-101@DMIP. CuKa radiation

111

(λ=1.5418 Å), a scan speed of 8° min−1 and a step size of 0.02° in 2θ were used. Thermogravimetric

112

analysis (TGA) was performed on a PTC-10A thermal gravimetric analyzer (Rigaku, Japan) under

113

air from room temperature to 700 °C at a ramp rate of 26 °C min−1.

114

Synthesis of MIL-101. MIL-101 was prepared according to the method of Hwang et al. with

115

some modifications.35 Typically, 0.8 g of terephthalic acid, 2 g of Cr(NO3)3·9H2O, and 63 µL of 40%

116

hydrofluoric acid were mixed thoroughly with 35 mL of ultra pure water and transferred into a 100

117

mL Teflon-lined reaction kettle. The reaction kettle was then heated at 220 °C in a muffle furnace for

118

8 h to give a suspension of green crystals of MIL-101. The precipitate was collected by filtration

119

after ultrasonic washing with water and centrifuging at 4000 rpm for 15 min. Finally, the obtained

120

MIL-101 was heated in water bath for 5 h at 70 °C, and then heated in ethanol for 3 h at 60°C. Green

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

121

crystals appeared after adding 200 mL of 30 mM NH4F and heating at 60 °C for 3 h. The resulting

122

MIL-101 was filtered off and activated under reduced pressure at 30 °C for 12 h.

123

Synthesis of MIL-101@DMIP. A pyrraline-imprinted polymer based on MIL-101 was

124

synthesized using a one-pot modified bulk polymerization technique. MIL-101@DMIP was

125

synthesized as follows: to a 25 mL round bottom flasks, PCC (0.2 g), acetonitrile (3 mL), the

126

prepared MIL-101 (0.02 g), and APTES (0.9 mL) were added, which was stirred for 60 min.

127

Subsequently, TEOS (2.2 mL) and acetic acid (0.2 mol L−1, 1 mL) were added. After stirring for 30

128

min, the pre-polymerized product was sealed and incubated in a glycerol bath at 60 °C for 20 h. The

129

obtained MIL-101@DMIP was extracted by Soxhlet extraction (200 mL of acetonitrile/acetic acid;

130

9:1, v/v) to remove the template until no PCC was detected by HPLC. To evaluate the performance

131

of MIL-101@DMIP, non-molecularly imprinted polymers (NIP) coated MIL-101 (MIL-101@NIP)

132

was prepared in the same way as described above, only in the absence of the template. The DMIP

133

without MOFs was prepared by the similar process as MIL-101@DMIP, but without MIL-101.

134

Static Adsorption and Selectivity Tests. To investigate the adsorption behavior of MIL-

135

101@DMIP, static adsorption and selectivity tests were performed. In the static adsorption test, 20

136

mg of MIL-101@DMIP and MIL-101@NIP were each exposed to 2 mL of PCC solutions of various

137

concentrations (4.3–430 µg mL−1) at room temperature for 12 h. After centrifugation, the

138

concentration of the free PCC in the supernatant solution was determined by HPLC and the amount

139

of the adsorbed PCC was estimated.

ACS Paragon Plus Environment

Page 8 of 32

Page 9 of 32

Journal of Agricultural and Food Chemistry

140

To evaluate the selectivity of MIL-101@DMIP towards pyrraline, a selectivity test was carried

141

out. CML, 3-pyrroline and pyrrole were used as the competitive substrate owing to analogous

142

structure. Selective binding was performed by fixing the concentration of CML, 3-pyrroline, pyrrole

143

and pyrraline at 5×10−6 mol L−1, and loading 400 µL of both solutions on to the SPE cartridge.

144

Elution was detected by HPLC.

145

HPLC Procedures. The HPLC conditions were taken from Manuel et al. with some

146

modifications.36 The standard solution was prepared by dissolving 5 mg of pyrraline standards in 10

147

mL of water and diluting the solution gradually from 2×10−3 to 5×10−8 mol L−1. Then, 5 µL aliquots

148

of these solutions were injected into a Shimadzu HPLC instrument equipped with an InertsilTM ODS-

149

SP analytical column (4.6×250 mm). The column was eluted using an acetonitrile/water gradient.

150

Solvent A was trifluoroacetic acid (TFA, 1 mL/L), solvent B was water/acetonitrile (1:1, v/v). The

151

proportion of solvent B was changed from 0% to15%, 20%, 100%, and 0% at 1, 10, 30, 35, 40, and

152

45 min, respectively. The flow rate was 1.0 mL min−1 and the ultraviolet detection wavelength was

153

297 nm.

154

Preparation of Food Samples. Pre-treatment of real samples was carried out using the

155

methods of Khan et al. and Yoshihara et al. with slight modifications.37,38 Three kinds of milk

156

samples, each kind with two brands, and six kinds of milk powder samples were used in the study.

157

To a centrifuge tube 0.5 mL of milk samples was added and then dissolved in 2.5 mL of methanol.

158

MIL-101@DMIP cartridges were prepared by packing 60 mg of MIL-101@DMIP into a 3 mL

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

Page 10 of 32

159

empty SPE cartridge and fixed using frits on both sides. The polymer bed was preconditioned with 3

160

mL of methanol followed by 3 mL of water. Then, 1 mL of the supernatant sample was loaded onto

161

the cartridge, and the cartridge was washed with 2 mL of water. Finally, pyrraline was eluted with 3

162

mL of methanol (5% ammonia solution). The SPE flow rates of sampling and eluation were 0.5

163

mL/min, respectively. The eluent was evaporated to dryness by ventilating with nitrogen. The dried

164

residue was then dissolved in 1 mL of water for analytical HPLC.

165 166

167 168

For milk powder samples, 0.5 mg of samples was dissolved in 2.5 mL of methanol and the remaining steps were the same as those for the milk samples. Statistical Analysis. The adsorption capacity (Q, µg g−1) was calculated from the concentrations of pyrraline before and after adsorption onto MIL-101@DMIP using the following equation, 5

169

Q = 1000000(C0 − Ci)×V×M/m

(1)

170

where C0 (mol L−1) is the initial concentration of pyrraline solution, Ci (mol L−1) is the pyrraline

171

concentration of the supernatant solution after the adsorption process, V (L) is the volume of the

172

initial pyrraline solution, M (g mol−1) is the molar mass of pyrraline, and m (g) is the mass of MIL-

173

101@DMIP or MIL-101@NIP.

174

The selectivity of MIL-101@DMIP towards pyrraline was determined by the following equations,

175

Kd = {(Co-Ci)/Ci}×V/m

(2)

176

K = Kd(pyrraline)/Kd(competitors)

(3)

ACS Paragon Plus Environment

Page 11 of 32

177 178 179

Journal of Agricultural and Food Chemistry

Where Co (mol L−1) and Ci (mol L−1) represent the initial and final concentrations of the substrates, respectively, V (mL) is the volume of the solution, and m (g) is the mass of the substrates. Data are expressed as mean ± standard deviation, and each value is the mean of triplicate

180

measurements. IBM SPSS Statistics 20.0 was applied to analyze the data.

181

Results and Discussion

182

Synthesis of MIL-101@DMIP. A one-step bulk polymerization strategy was used to prepare

183

MIL-101@DMIP, the general scheme for the preparation process is illustrated in Figure 1. PCC was

184

used as the dummy template owing to its analogous structure and lower cost compared with pyrraline.

185

MIL-101 was used as the core of the core–shell composite structure, embedded into an MIP shell.

186

This aimed to improve the adsorption efficiency of traditional MIP. The MIP formed on the surface

187

of MIL-101 through hydrogen-bond interaction of PCC and APTES (functional monomer), and

188

cross-linking by TEOS.

189

Morphological Characterization of the Polymers. As shown in Figure 2a, the average diameter

190

of the octahedral MIL-101 particles were ranged from 300-500 nm, and their surfaces were smooth.

191

Figure 2b shows that the MIP fully encapsulated the MIL-101 after polymerization. However, after

192

encapsulation, MIL-101@DMIP featured a spherical structure with an average size were about 400-

193

600 nm. The surface of MIL-101@DMIP was not smooth, which dotted with specific cavities left by

194

the template.

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

195

FT-IR Spectra. FT-IR spectroscopy was employed to characterize the formation of synthesized

196

MIL-101, MIL-101@DMIP, and MIL-101@NIP, as illustrated in Figure 3a, 3b, and 3c, respectively.

197

As shown in Figure 3a, the band observed at 746 cm−1 in the spectrum of MIL-101 was attributed to

198

Cr–O. The bands observed at 1168 cm−1 and 1540-1695 cm−1 were attributed to O–C–O and C=C,

199

and indicate that benzene rings and carboxylic groups were incorporated into MIL-101. Finally, the

200

band observed at 3362 cm−1 was attributed to adsorbed water. Figure 3b shows that the spectrum of

201

MIL-101@DMIP displays a band at around 1540-1695 cm−1, which demonstrates the existence of

202

MIL-101. The bands observed at 780 cm−1 and 1038 cm−1 were attributed to N–H and O–Si–O,

203

respectively. These bands indicate the presence of the functional monomer and the cross linker, and

204

confirm the successful encapsulation process between MIL-101 and the DMIP. The spectrum of

205

MIL-101@NIP in Figure 3c contains similar bands to those in the spectrum in Figure 3b, showing

206

that MIL-101@DMIP and MIL-101@NIP possess similar chemical structures.

207

XRD Analysis. MIL-101 and MIL-101@DMIP were further analyzed by XRD. The main

208

characteristic peaks in the diffractograms of MIL-101, shown in Figure 4a, were observed at 2θ 7.98°

209

and 9.06°. While in Figure 4b,it is noteworthy that the intensity of the MIL-101 XRD peaks

210

decreased significantly after the surface-imprinting process as a consequence of the successful

211

coating procedure.

212

TGA Analysis. TGA was conducted to determine the thermal stability of MIL-101 and MIL-

213

101@DMIP. As shown in Figure 5a, MIL-101 displayed an initial weight loss of 11.12% below

ACS Paragon Plus Environment

Page 12 of 32

Page 13 of 32

Journal of Agricultural and Food Chemistry

214

200 °C owing to water loss from the framework. A second weight loss of 5.18% observed at 200–

215

360 °C was ascribed to the disintegration of the OH/F groups of MIL-101. The thermo gram of MIL-

216

101@MIP is shown in Figure 5b. Compared with the slope of Figure 5a, that of Figure 5b seemed

217

gentle. Only 1.08% weight loss within the temperature range of 25-100 °C was observed. Most of the

218

real sample detections are carried out in the temperature range. When the temperature was from 100

219

to 200 °C, the weight of MIL-101@MIP was reduced 10.31%. However, only one significant weight

220

loss of was observed within the range of 100–600 °C for MIL-101@DMIP. This phenomenon shows

221

that the synthesized MIL-101@MIP feature good thermal stability, which would be a desirable

222

attribute in relevant applications.

223

Adsorption Isotherm. As shown in Figure 6, the adsorption capacities of MIL-101@DMIP

224

increase with an increase in the initial concentration of PCC. The adsorption capacity of the MIL-

225

101@DMIP (up to 21.7 mg/g) was about 14.5 times of MIL-101@NIP (up to 1.5 mg/g). It indicates

226

that MIL-101@DMIP exhibits a higher binding affinity for PCC than does MIL-101@NIP, and that

227

the specific recognition sites were successfully established during the molecular imprinting process.

228

Specificity of MIL-101@DMIP. CML, 3-pyrroline and pyrrole have a similar chemical

229

structure to pyrraline, and were thus employed to investigate the binding selectivity of MIL-

230

101@DMIP. The structures of 3-pyrroline, pyrrole and pyrraline have similar ring structure, but with

231

different substituent groups. CML has the similar recognition sites of lysine but without ring

232

structure. As illustrated in Table 1, the adsorption capacity of MIL-101@DMIP for pyrraline is

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

233

significant difference with 3-pyrroline, pyrrole and CML. The results summarize the data (Kd and K)

234

which were obtained in competitive binding experiments. The large Kd value of the MIL-

235

101@DMIP was an indication of its high selectivity for pyrraline over the competitors due to the

236

tailor-made cavities in the MIL-101@DMIP. The distribution coefficients for the analytes on the

237

MIL-101@DMIP were 58.82, 1.37, 46.59, and 4.38, respectively. The selectivity coefficients for the

238

three competitors were 713.00, 41.94, and 475.33 for the MIL-101@DMIP. It indicates that MIL-

239

101@DMIP shows good selectivity towards pyrraline molecules.

240

Validated Method for the MIL-101@DMIP. The practicality of the developed method was

241

validated by comparison with OASISTM HLB 3cc extraction cartridges (HLB)9, MIP-without MOF,

242

and MIL-101@DMIP. The results of the three methods were shown in Table S1. It indicated that the

243

prepared MIL-101@DMIP column was significant advantage with the HLB, and MIP-without MOF

244

column. When the HLB cartridge was applied to extraction, the recoveries of pyrraline were lower

245

than 90%. But the recovery of MIL-101@DMIP is higher than 90%, which indicated that the

246

prepared MIL-101@DMIP column accurately detected pyrraline. The recovery of MIL-101@DMIP

247

is higher than MIP-without MOF, especially at a low concentration. It indicated that the MIL-101

248

material enhance the efficiency for target detection.

249

Reproducibility and Precision of MIL-101@DMIP. The reproducibility of pyrraline detection

250

by MIL-101@DMIP was investigated by measuring the peak area at a pyrraline concentration of

251

2.5×10-5 M. After each measurement, 400 µL of pyrraline solution was reloaded onto the SPE

ACS Paragon Plus Environment

Page 14 of 32

Page 15 of 32

Journal of Agricultural and Food Chemistry

252

cartridge,the absorbed pyrraline was eluted by methanol (5% ammonia) and quantified by HPLC.

253

A relative standard deviation of 4.53% was obtained for four repeated detections. This suggests that

254

the repeatability of the new method is suitable for practical application.

255

Detection of Pyrraline in Foods by MIL-101@DMIP. To assess the practicality of the

256

prepared MIL-101@DMIP and MIL-101@NIP, these compounds were employed as sorbents for the

257

extraction of pyrraline from food samples. The extracted pyrraline content was measured by HPLC,

258

and a detection limit of 40.7 µg/L (S/N ≥ 3), and a linear range of 5×10−7–2×10−3 mol L−1 were

259

found. To demonstrate the feasibility and reliability of the developed and optimized method, it was

260

applied to the analysis of milk and milk powder samples for the determination of pyrraline. As

261

shown in Table 2, the pyrraline was not detected in the nutritional milk powder for women, high

262

calcium milk powder for children, high zinc milk powder for students, and whole milk powder. It

263

was the highest in nutritional powder milk for quinquagenarian (162.78 µg/g). The pyrraline was

264

detected in all milk samples, ranged from 11.63-17.75 µg/mL. Pyrraline is formed by the non-

265

enzymatic reaction of reducing sugars with side-chain amino groups of milk and milk powder,

266

during the process of heating, sterilization, pasteurization or storage.

267

The recovery was calculated by comparing the analytical signals of pyrraline obtained from

268

spiked high calcium milk samples with 0.36, 4.39 and 28.07 µg/mL pyrraline concentrations. As

269

shown in Table S2, the recoveries ranged from 92.23% to 103.87%, with relative standard deviations

270

of 4.46%–6.87%, which indicates the excellent ability of the prepared MIL-101@DMIP for

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

271

recognizing pyrraline in complex food matrices, as well as its potential for application in the

272

detection of pyrraline.

273

Conclusion. In this work, MIL-101@DMIP was synthesized by one-pot bulk polymerization.

274

The synthesized MIL-101@DMIP exhibited a high adsorption capacity and excellent binding affinity,

275

and was successfully employed as a sample pre-treatment in the HPLC detection of pyrraline

276

residues in food samples. Our innovative synthetic route provides a new method for the production

277

of MIL-101@DMIP with faster mass transport speed, tunable pore structure, high specific

278

recognition ability, and high selectivity. This holds promise for future applications in the food,

279

agricultural, and aquacultural industries.

280

AUTHOR INFORMATION

281

Corresponding Author

282

*(J.W.) Phone: +86 10-68984545. Fax: +86 10-68985456. Email: [email protected].

283

Funding

284

This work was supported by the National Natural Science Foundation of China (No. 31571940, and

285

No. 31501559), Beijing Excellent Talents Funding for Youth Scientist Innovation Team, and the

286

Construction of Scientific Research Base and Innovation Platform (No. 19008001226).

287

Notes

288

The authors declare no competing financial interest.

ACS Paragon Plus Environment

Page 16 of 32

Page 17 of 32

Journal of Agricultural and Food Chemistry

289

References

290

(1) Tessier, F.J. The Maillard reaction in the human body. The main discoveries and factors that

291

affect glycation. Pathol Biol. 2010, 58, 214–219.

292

(2) Li, Y.; Zhang, Y.; Chen, C. Establishment of a rabbit model to study the influence of advanced

293

glycation end products accumulation on osteoarthritis and the protective effect of pioglitazone.

294

Osteoarthritis and Cartilage. 2016, 24, 307–314.

295

(3) Nersten, H. The Maillard reaction:chemistry, biochemistry and implications. Industry Chem.

296

(4) Alison, G.; Joshua, A.; Beckman, A. M. S. Advanced glycation end products sparking the

297 298 299

development of diabetic vascular injury. Circulation. 2006, 114, 597–605. (5) John, W.B. The role of AGEs in aging causation or correlation. Experimental Gerontology. 2001, 36, 1527–1537.

300

(6) Nakayama, T.; Hayase, F.; Kato, H. Formation of ε-(2-formyl-5-hydroxy-methyl-pyrrol-1-yl)-L-

301

norleucine in the maillard reaction between D-glucose and L-lysine. Agric Biol Chem. 1980,

302

44, 1201–1202.

303

304

(7) Chuyen, V.N. Toxicity of the AGEs generated from the Maillard reaction on the relationship of food-AGE sand biological-AGEs. Mol. Nutr. Food Res. 2006, 50, 1140–1149.

305

(8) Sengl, M.; Ledl, F.; Severin, T. Maillard-reaktion von rinderserumalbumin mit glucose

306

hochleistung-flüssigkeitschromatographischer nachweis des 2-formyl-5-(hydroxymethyl)pyrrol-

307

1-norleucins nach alkalischer hydrolyse. J. Chromatogr A. 1989, 463, 119–125.

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

308

309 310

Page 18 of 32

(9) Kazuhiro, Y.; Reiko, K.; Yumi, S. Determination of Urinary Pyrraline by Solid-Phase Extraction and High Performance Liquid Chromatography. Biol. Pharm. Bull. 2001, 24, 863–866. (10) Thomas, H.; Henning, K. Determination of protein-bound 2-amino-6-(2-formyl-l-pyrrolyl)-

311

hexanoic

acid

("pyrraline") by ion

exchange chromatography

312

detection. Z Lebensm Unters For. 1993, 196, 1–4.

and photodiode

array

313

(11) Liu, H.L.; Zhou, K.W.; Wu, D. A novel quantum dots-labeled on the surface of molecularly

314

imprinted polymer for turn-off optosensing of dicyandiamide in dairy products. Biosens.

315

Bioelectron. 2016, 77, 512–517.

316

(12) Ding, Z.Q.; S.W.Bligh, A.; Tao, L. Molecularly imprinted polymer based on MWCNT-QDs as

317

fluorescent biomimetic sensor for specific recognition of target protein. Materials Science and

318

Engineering C. 2015, 48, 469–479.

319

(13) Haginaka, J.; Takehira, H.; Hosoya, K. Uniform-sized molecularly imprinted polymer for (S)-

320

naproxen selectively modified with hydrophilic external layer. J. Chromatogr. A. 1999, 849,

321

331-339.

322

323 324

325

(14) Chen, L.; Wang, X.; Lu, W.; Wu, X.Q.; Li, J.H. Molecular imprinting: perspectives and applications. Chem.Soc.Rev. 2016, 45(8), 2137-2211. (15) Chen, L.X.; Xu, S.F.; Li, J.H. Recent advances in molecular imprinting technology: current status, challenges and highlighted applications. Chem. Soc. Rev. 2011, 40 (5), 2922-2942.

ACS Paragon Plus Environment

Page 19 of 32

326

327

Journal of Agricultural and Food Chemistry

(16) Song, X.; Xu, S.; Chen, L.; Wei, Y.; Xiong, H. Recent advances in molecularly imprinted polymers in food analysis. J. Appl.Polym.Sci. 2014, 131(16), 40766-40784.

328

(17) Zhang, Z.; Xu, S.; Li, J.; Xiong, H.; Peng, H.; Chen, L. Selective solid-phase extraction of

329

Sudan I in chilli sauce by single-hole hollow molecularly imprinted polymers. J. Agric. Food.

330

Chem. 2011, 60(1), 180-187.

331

(18) Tang, Y.; Lan, J.; Gao, X. Determination of clenbuterol in pork and potable water samples by

332

molecularly imprinted polymer through the use of covalent imprinting method. Food chem.

333

2016, 190, 952–959.

334

335

(19) Tan, J.; Li, R.; Jiang, Z.T. Discrimination of fresh fruit juices by a fluorescent sensor array for carboxylic acids based on molecularly imprinted titania. Food Chem. 2014, 165, 35–41.

336

(20) Zhu, F.L.; Wang, J.; Zhu, L.J. Preparation of molecularly imprinted polymers using theanine as

337

dummy template and its application as SPE sorbent for the determination of eighteen amino

338

acids in tobacco. Talanta. 2016, 150, 388–398.

339

340 341

342

(21) Maciej, C.; Katarzyna, S.; Marta, S. Selective electrochemical sensing of human serum albumin by semi-covalent molecular imprinting. Biosens. Bioelectron. 2015, 74, 960–966. (22) Rosi, N.; Eckert, J.; Eddaoudi, M.; Vodak, T.; Kim, J.; O’Keeffe, M.; Yaghi, O.M. Hydrogen storage in microporous metal-organic frameworks. Science. 2003, 300, 1128.

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

Page 20 of 32

343

(23) Duan, X.; Cai, J.; Yu, J. Three-dimensional copper (II) metal–organic framework with open

344

metal sites and anthracene nucleus for highly selective C2H2/CH4 and C2H2/CO2 gas separation

345

at room temperature. Microporous Mesoporous Mater. 2013, 181, 99–104.

346

(24) Guo, C.; Jin, Q.; Wang, Y. Developing a unique metal-organic framework-{[Cd(abtz)2

347

(NCS)]·(ClO4)}n (abtz= 1-(4-aminobenzyl)-1, 2, 4-triazole) as fluorescent probe for highly

348

selective and sensitive detection of ascorbic acid in biological liquid. Sens. Actuators, B. 2016,

349

234, 184–191.

350

351

(25) Qian, K.; Deng, Q.L.; Fang, G.Z. Metal–organic frameworks supported surface–imprinted nanoparticles for the sensitive detection of metolcarb. Biosens. Bioelectron. 2016, 79, 359–363.

352

(26) Dai, X.P.; Jia, X.N.; Zhao, P. A combined experimental/computational study on metal-organic

353

framework MIL-101(Cr) as a SPE sorbent for the determination of sulphonamides in

354

environmental water samples coupling with UPLC-MS/MS. Talanta. 2016, 154,581-588.

355

(27) Lv, Z.X.; Sun, Z.W.; Song, C.H. Sensitive and background-free determination of thiols from

356

wastewater

357

chromatography with fluorescence detection using a novel fluorescence probe of carbazole-9-

358

ethyl-2-maleimide. Talanta. 2016, 161, 228-237.

359

360

samples

by

MOF-5

extraction

coupled

with

high-performance

liquid

(28) Huang, Z.Z.; Lee, H.K. Micro-solid-phase extraction of organochlorine pesticides using porous metal-organic framework MIL-101 as sorbent. J. Chromatogr. A. 2015, 1401, 9-16.

ACS Paragon Plus Environment

Page 21 of 32

Journal of Agricultural and Food Chemistry

361

(29) Wang, X.Y.; Deng, C.H. Preparation of magnetic graphene @polydopamine @Zr-MOF

362

material for the extraction and analysis of bisphenols in water samples. Talanta. 2015, 144,

363

1329–1335.

364

(30) Ma, J.; Yao, Z.; Hou, L.; Lu, W.; Yang, Q.; Li, J.; Chen, L. Metal organic frameworks (MOFs)

365

for magnetic solid-phase extraction of pyrazole/pyrrole pesticides in environmental water

366

samples followed by HPLC-DAD determination. Talanta.2016, 161,686-692.

367 368

(31) Qian, K.; Fang, G.Z.; Wang, S. A novel core-shell molecularly imprinted polymer based on metal-organic frameworks as a matrix. Chem. Commun.2011, 47, 10118–10120.

369

(32) Madiha, B.; Anca, F.; Cecilia, C.; Robert, S.; Francis, V.; Abdelhamid, E.; Benachir, B.;

370

Nezha, E.B.; Nicole, J.R. Development of a novel sensitive molecularly imprinted polymer

371

sensor based on electropolymerization of a microporous-metal-organic framework for

372

tetracycline detection in honey. Food Control. 2016, 59, 424–429.

373

(33) Zofia, I.; Piyush, S. S.; Daniel, P.; Krzysztof, F.; Francis, D.S.; Diana, T.; Filip, S.; Krzysztof, N.

374

Molecularly Imprinted Polymer (MIP) Film with Improved Surface Area Developed by Using

375

Metal–Organic Framework (MOF) for Sensitive Lipocalin (NGAL) Determination. Appl. Mater.

376

Interfaces, 2016, 31, 19860–19865.

377

(35) Hwang, Y.K.; Hong, D.Y.; Chang, J. S. Amine grafting on coordinatively unsaturated metal

378

centers of MOFs: consequences for catalysis and metal encapsulation. Angew. Chem., Int. Ed.

379

2008, 47(22), 4144–4148.

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

380

(36) Manuel, P.O.; Ramanakoppa, H.; Nagaraj, V.; Monnier, M. Chromatographic evidence for

381

pyrraline formation during protein glycation in vitro and in vivo. Biochimica et Biophysica

382

Acta. 1995, 1247, 74–80.

383

(37) Yoshihara, K.; Kiyonami, R.; Shimizu, Y. Determination of urinary pyrraline by solid-phase

384

extraction and high performance liquid chromatography. Biol. Pharm. Bull. 2001, 24(8), 863–

385

866.

386

(38) Khan, S.; Bhatia, T.; Trivedi, P. Selective solid-phase extraction using molecularly imprinted

387

polymer as a sorbent for the analysis of fenarimol in food samples. Food Chem. 2016, 199,

388

870–875.

ACS Paragon Plus Environment

Page 22 of 32

Page 23 of 32

Journal of Agricultural and Food Chemistry

389

FIGURE CAPTIONS

390

Figure 1. Schematic of the molecular imprinting process for the synthesis of MIL-101@DMIP.

391

Figure 2. Scanning electron micrographs of (a) MIL-101, and (b) MIL-101@DMIP.

392

Figure 3. Fourier transform infrared spectra of (a) MIL-101, (b) MIL-101@DMIP, and (c) MIL-

393

101@NIP.

394

Figure 4. X-ray diffraction patterns of (a) MIL-101 and (b) MIL-101@DMIP.

395

Figure 5. Thermogravimetric analysis of (a) MIL-101 and (b) MIL-101@DMIP.

396

Figure 6. Binding isotherms of MIL-101@DMIP and MIL-101@NIP.

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

397

Table 1 The specificity of MIL-101@DMIP. Sorbents

MIP

pyrraline

58.82

CML

1.37

3-Pyrroline

46.59

Pyrrole

4.38

pyrraline

14.26

CML

0.02

3-Pyrroline

0.34

Pyrrole

0.03

CML

713.00

3-Pyrroline

41.94

Pyrrole

475.33

Loading capacity (µg/g)

Kd

K

398 399

ACS Paragon Plus Environment

Page 24 of 32

Page 25 of 32

400

Journal of Agricultural and Food Chemistry

Table 2 The determination of pyrraline in milk and milk powder samples (n=3).

401

Samples

Content (µg/g or µg/mL)

Nutritional powder milk for women

0

High calcium milk powder for children

0

Nutritional powder milk for quinquagenarian

160.67± 3.15

High zinc milk powder for students

0

Whole milk powder

0

Modified milk powder

162.78 ± 0.04

High calcium milk 1

15.21 ± 0.31

High calcium milk 2

17.75 ± 0.41

Pure milk 1

15.43 ± 0.28

Pure milk 2

14.25 ± 0.04

Breakfast milk 1

11.63 ± 0.21

Breakfast milk 2

12.73 ± 0.19

402

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

40x32mm (600 x 600 DPI)

ACS Paragon Plus Environment

Page 26 of 32

Page 27 of 32

Journal of Agricultural and Food Chemistry

19x7mm (600 x 600 DPI)

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

40x28mm (600 x 600 DPI)

ACS Paragon Plus Environment

Page 28 of 32

Page 29 of 32

Journal of Agricultural and Food Chemistry

18x6mm (600 x 600 DPI)

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

18x7mm (600 x 600 DPI)

ACS Paragon Plus Environment

Page 30 of 32

Page 31 of 32

Journal of Agricultural and Food Chemistry

40x28mm (600 x 600 DPI)

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

19x3mm (600 x 600 DPI)

ACS Paragon Plus Environment

Page 32 of 32