Multiple-Unit Fusion Rack - ACS Publications

A MULTiPLE-unit fusion rack was developed in the U. S. Geo-. ' logical Survey to facilitate the fusion of approximately 20,000 soil and rock samples p...
0 downloads 0 Views 257KB Size
273

V O L U M E 28, N O . 2, F E B R U A R Y 1 9 5 6 It is evident that the apparatus is capable of measuring a broad range of gel times. Table I1 gives an example of a study of quality control, in which the gel times of resin from seven barrels were determined in duplicate. The estimated standard deviation for a single determination from this series of duplicate determinations, calculated from the formula

where k is the difference betneen duplicate determinations, and ~n is the number of duplicate determinations, is 0.11 hour, or 2.3% of the average value of 4.8 hours. ACKNOWLEDGMENT

This paper is based upon work performed for the Xavy Department, Bureau of Aeronautics, under Contract NOa(s) 10146 with the A4erojet-GeneralCorp. LITERATURE CITED

(1) Foord, Y. G., J . Chem. SOC. (London) 40, 48 (1940). ( 2 ) €Eggens, H. G., and Plomley, K. F., Xature 163, S o . 4131, 22 (1949). ( 3 ) Nichols, P. L., and Yanovsky, E., J . Am. Chem. SOC.66, 1625 (1944.

Rohm & Haas Co., Resinous Products Division, Philadelphia, Pa., private communication. (5) Toy, -4.D. F., and Brown, L. V.,I n d . Eng. Chem. 40, 2276 (4)

soil and rock samples per year, preparat,ory to the determination of many trace constituents. Previously, a small sample n-as mixed with the appropriate flux in a borosilicate glass test tube, the fusion was made by heating in a rack over a Bunsen burner, and finally the tube was rotated manually as it cooled, to obtain a thin coating of the melt, on the sides of the test tube to facilitate dissolving the product. By means of the multiple-unit fusion rack, in use for the past gear, 11 fusions can be made simultaneously. The equipment serves three purposes: It provides a uniform sample treatment to improve the precision of the analytical methods ; it automatically rotates the cooling tubes so that the molten flux solidifies in a thin layer; and it saves much time and effort. The apparatus (shown in Figures 1 and 2) heats each test tube uniformly by constaritly passing the tube, rotating on the axis of the unit,, over a series of burners for a definite time. The rotation of each test tube keeps the sample in intimate contact with the molten flux t,o provide adequate sample treatment, and during the cooling cycle causes the melt to coat the wall of the tube with a thin layer of the fusion product a b it solidifies. Neither of these procedures requires the attention of an operator; the operator is relieved of the manual procedure that was necessary prior to thr drvelopnient of the multiple-unit fusion rack. CONSTRUCTION

.1 perspective dimc~rsionaldrawing is shown in Figure 1. The entire unit is 23 inches long, 12 inches wide, and 16 inches high, and reighs approximately 45 pouiirls.

(1948). ((j)

Vincent. €1. L.. Ihiil., 29, 1267 (1937).

Multiple-Unit Fusion Rack A. P. Marranzino and William H. Wood, U. S. Geological Survey, Denver Federal Center, Denver, Colo.

fusion rack was developed in the U. S. Geo14.mnTIPLE-unit logical Surve>-to facilitate the fusion of approximately 20,000 '

Figure 2.

Figure 1.

Drive mechanism

Burner assembly

The carriage assembly for holding tho test tubes is rotatecl a t 15 r.p.m. by a 1/75-h.p., 115-volt, alternating current, continuous-action, gear-reducing motor connerted to the drive shaft of the carriage by a chain drive (a S o . 1A steel ladder chain having a yield point of 37 pounds). A sprocket (ao-teeth, 1.18inch pitch diameter n-ith a '/&-inch hub t h a t has a S/le-inch hole) is mounted on the drive shaft of the motor and is connected by the chain to a sprocket of the same size betueen the aluminum bearing posts of the carriage. This arrangement gives the drive unit a 1t o 1 ratio; other ratios may be obtained by a suitable selection of sprockets and chains. A fan is mounted on the motor and serves both to cool the

2'14

ANALYTICAL CHEMISTRY

mot'or and to drive any corrosive fumes away from the unit. Safety covers are mounted over both the fan and the chain drive. The carriage shaft is carried by two roller bearings. The carriage assembly is fastened to the end of the drive shaft by a brass flange and is made of two 3/8-inch asbestos cement disks, 57/8 inches in diameter, which are separated by a ll/n-inch brass insert 1 inch in diameter. Eleven semicircular sectors, 3/( inch in diameter, have been cut out of the circumference of the disks a t equal intervals. Eleven steel posts ( I / * X 1 3 / r inches) are fastened with silver solder on the brass insert in a line with the 11 semicircular sectors. A curved test tube clamp, 6 / * inch wide, fashioned from l/sp-inch sheet stainless steel is fastened to the end of the 11 posts with silver solder. The motor, gears, and carriage are mounted on an aluminum plate (see Figure 1) t h a t is fastened to the chassis by a pianotype hinge placed under the chain-drive assembly. A thumbscrew a t the opposite end of the plate allows the entire unit to be rotated about the hinge to 20 degrees from the horizontal and thus permits the closed end of the test tube to be depressed into the furnace unit. TWO flat brass ways, X 1 1 / 2 inches, on the underside of the furnace are fitted to two T-shaped aluminum ways fastened to the chassis, providing tracks on which the furnace moves. The furnace is constructed from 0.5-inch asbestos cement board and is assembled with machine screws. Figure 2 illustrates interior design and Figure 1 gives dimensions. A curved slot is cut in the back wall of the furnace t,o permit the entry of the carriage when the furnace is moved toward the motor and gear assembly. Twenty holes, inch in diameter, are drilled along the lov,-er edges of the sides and front of the furnace to furnish sufficient ventilation for the gas burners. Five high-temperature natural gas-type burners, whose bases have been cut to permit close assemblage, are connected t o a copper manifold by short lengths of rubber tubing. The burners can be regulated in the normal manner and cau be removed easily for occasional cleaning. The front of the furnace is a door held by two piano-type hinges 1.5 inches in length and fastened by a hook and eye. A projecting handle is plac.ed on the door t o facilitate moving the furnace. is made of Ixird pine painted r i t h heat-rcsist:int 1not:il paint.

takes a t least 4 hours-and requires a special apparatus and equipment. This paper reports an electrolytic oxidation method for plutonium which is faster and simpler than ozonation and is still quantitative and exclusive of foreign ions. APPARATUS

The electrolysis apparatus is similar to that described by iMiller and Brouns, except that a polyethylene bottle and screw cap without gaskets are used for the electrodeposition cell. The cathode is a platinum wire coated with paraffin, except for an area of approximately 0.033 sq. cm. a t the tip. PROCEDURE

The plutonium solution is transferred to the assembled electrodeposition cell and made 0.5N in perchloric acid and 10 ml. in volume. A 20-sq. cm. platinum anode is rotated to produce vigorous stirring. The platinum mire cathode is placed in the cell, and a current of 60 ma. is passed through the solution for 15 minutes. The plutonium is 98% oxidized a t the end of this time as determined by lanthanum fluoride carrying of plutonium(II1) and ( I T ) . If electrodeposition is desired, sodium hydroxide iadded to adjust the hydroxide ion concentration and the deposition is performed as described by hIiller and Brouns. RESULTS

.

A perchloric acid concentration of 0.531 was found to be the optimum for the oxidation (Table I). A current of at least 30 ma. was required for efficient ovidation a t a 5-sq. em. anode Decreasing the anodic current density increased the plutonium oxidation efficiency as shown in Table 11. Plutonium was 98% oxidized a t 3 ma. per sq. em. The oxidation is essentially complete in a matter of minutes. Microgram quantities n ere 98% oxidized in I O minutes, milligram amounts in 15 (Table 111).

OPERATIOS

The fiisiou is accoinpli~hrdin tht, miiltiple-unit fmion rack as follow:

Table I. Effectof Perchloric Acid Concentration on Anodic Oxidation of Plutonium

The position of the furnace and the carriage a t the beginning of the fusion is.shown in Figure 2. Eleven 16 X 150 mm. borosilicate glass test tubes cont,aining the samples of soil or rock mixed witl? an appropriate flux are placed around the periphery of the carriage. The carriage is adjusted by the thumbscrew to lower the bottom end of t,lie test tubes, and the motor is started. The buruers are then lighted and the furnace is pushed under the revolving test tubes. After the fusion is completed, the furnacr is withdrawn from the carriage, which is then adjusted to support the test tubes in a horizontal position. The unit is allowed to rotate until the melt has solidified o n the sides of the test tubes in :I thin laye:.

(65 ma., 5-sq. em. P t anode, 0.5 y of plutonium, 1-how electrolysis)

While the fusion process is taking place, the operator is free t,o utilize his time on another operation, thus cutting doxn greatly the number of man-hours spent iii making a large number of test tube fusions.

PI,

HCIOI,

M

55

0.1 0.2 0.25

88

88 ~. 92 78 72 50

0.5 1.0 2.0 4.0

Table 11. Effect of Anodic Current Density on Electrolytic Oxidation of Plutonium Pu

Taken for Oxidation 1.5?

P u r l ~ r c a ~ i authorized ns by the Director, 11,S. Geological Survey.

(60 ma., 0.5.W HClO,, I-hour electrolysis) Pi1 Anodic Current Oxidized, Density, Ma./Sq. Cm. % 30 72.0 15 91.3 6 97.0 3 97.8 1.5 97.2

1 .5 m g .

6 3 1 5

97.5 97.8 99.0

Electrolytic Oxidation of Plutonium Roy KO, General Electric Co., Hanford Atomic Products Operation, Richland, Wash.

quantitative electrodeposition of plutonium by the method of Miller and Brouns [Miller, H. W., and Brouns, K. J , A.v.4~.CHEM.24, 536 (1982)],in which Pu(V1) is reduced cathodically in n potassium hydroxide solution and deposited as Pu( OH)4> the metal must be in the sexivalent state. The most suitable oxidation method has been ozoriation ( AIiller and Brouns), which ovidizes plutonium quantitatively without introducing ions which interfere in the electrodeposition. Ozonation, howevcv, i 4 slow-the oxidation of milligram amounts of plutonium OR

F

Table 111. Effect of Time on Anodic Oxidation of Plutonium Pu

Taken for Oxidation 1.5 y

1.5 mg.

(3 ma./sq. cm., 0.5.W HClOd Time of Oxidation, Min. 5 10 15

30 60 10 15 30 GO

Pu

Oxidized, 76

85.6 97.8 RB.9 96.7 97.8 95.4 98.3 98.6 99.0