Multispecies Biofilms Transform Selenium Oxyanions into Elemental

Jan 29, 2016 - Erika J. Espinosa-Ortiz , Yoan Pechaud , Ellen Lauchnor , Eldon R. Rene , Robin Gerlach , Brent M. Peyton , Eric D. van Hullebusch , Pi...
0 downloads 0 Views 2MB Size
Subscriber access provided by GAZI UNIV

Article

Multispecies biofilms transform selenium oxyanions into elemental selenium particles: studies using combined synchrotron X-ray fluorescence imaging and scanning transmission X-ray microscopy Soo In Yang, Graham N. George, John R. Lawrence, Susan G. W. Kaminskyj, James J. Dynes, Barry Lai, and Ingrid J. Pickering Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.5b04529 • Publication Date (Web): 29 Jan 2016 Downloaded from http://pubs.acs.org on February 2, 2016

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 32

Environmental Science & Technology

Multispecies biofilms transform selenium oxyanions into elemental selenium particles: studies using combined synchrotron X-ray fluorescence imaging and scanning transmission X-ray microscopy Soo In Yang,† Graham N. George,† John R. Lawrence,‡ Susan G. W. Kaminskyj,§ James J. Dynes,ǁ Barry Lai,⊥ Ingrid J. Pickering*† †

Department of Geological Sciences, University of Saskatchewan, Saskatoon, Saskatchewan S7N 5E2, Canada



National Hydrology Research Centre, Environment Canada, Saskatoon, Saskatchewan S7N 3H5, Canada §

Department of Biology, University of Saskatchewan, Saskatoon, Saskatchewan S7N 5E2, Canada

ǁ

Canadian Light Source, 101 Perimeter Road, Saskatoon, Saskatchewan S7N 0X4, Canada



Advanced Photon Source, Argonne National Laboratory, Argonne, Illinois 60439, United States

1 ACS Paragon Plus Environment

Environmental Science & Technology

Page 2 of 32

1

ABSTRACT

2

Selenium (Se) is an element of growing environmental concern, as low aqueous concentrations

3

can lead to biomagnification through the aquatic food web. Biofilms – naturally occurring

4

microbial consortia – play numerous important roles in the environment, especially in

5

biogeochemical cycling of toxic elements in aquatic systems. The complexity of naturally

6

forming multispecies biofilms presents challenges for characterization since conventional

7

microscopic techniques require chemical and physical modification of the sample. Here,

8

multispecies biofilms biotransforming selenium oxyanions were characterized using X-ray

9

fluorescence imaging (XFI) and scanning transmission X-ray microscopy (STXM). These

10

complementary synchrotron techniques required minimal sample preparation and were applied

11

correlatively to the same biofilm areas. Submicron XFI showed distributions of Se and

12

endogenous metals, while Se K-edge X-ray absorption spectroscopy indicated the presence of

13

elemental Se (Se(0)). Nano-scale carbon K-edge STXM revealed the distributions of microbial

14

cells, extracellular polymeric substances (EPS) and lipids using the protein, saccharide and lipid

15

signatures, respectively, together with highly localized Se(0) using the Se LIII-edge.

16

Transmission electron microscopy showed the electron-dense particle diameter to be 50-700 nm,

17

suggesting Se(0) nanoparticles. The intimate association of Se(0) particles with protein and

18

polysaccharide biofilm components has implications for selenium’s bioavailability in the

19

environment.

20

2 ACS Paragon Plus Environment

Page 3 of 32

Environmental Science & Technology

21

INTRODUCTION

22

Selenium (Se, Z=34), an essential micronutrient in animals and certain microorganisms,

23

serves as a catalytic element within the active site of several types of antioxidant enzymes such

24

as thioredoxin reductase.1,2 In addition, although plants lack a requirement for this element, a

25

positive role for selenium such as an increase in yield has been suggested for certain species.3,4

26

Despite its beneficial role, selenium can be toxic at elevated levels and in most organisms tends

27

to have a narrow margin between required and toxic levels.5 Selenium can cause toxicity by a

28

number of mechanisms, including mimicking or disturbing sulfur metabolism6 and damaging

29

cells by oxidative stress7 in most organisms, including humans. The environmental risks from

30

selenium contamination are of increasing concern and can arise from a variety of sources,

31

including mining, agricultural water use and power plant emissions.8-10 Relatively low levels of

32

selenium entering the aqueous environment due to anthropogenic activities can be biomagnified

33

through aquatic food webs11,12 with accumulated levels of selenium causing adverse effects

34

especially in larval stages of oviparous vertebrates including birds and fish.13-15 The initial

35

biotransformation of aqueous oxyanions selenate and selenite by microorganism communities is

36

a key component of this biomagnification.11,12

37

In the aqueous environment, microorganisms favor growing as communities known as

38

biofilms by forming and incorporating a slimy matrix of extracellular polymeric substances

39

(EPS). Microorganisms in biofilm communities have shown a high resistance to toxic elements

40

compared with their free-living planktonic counterparts.16-18 One advantage for microorganisms

41

living in community as a biofilm is the ease of metabolic control using cell-to-cell

42

communication in response to environmental changes.19 Hence, the prevalent yet complex

43

structure of biofilms typically confers increased tolerance to physical, chemical, and biological 3 ACS Paragon Plus Environment

Environmental Science & Technology

Page 4 of 32

44

stress compared to free-living microorganisms.16-18 Therefore, biofilm formation is evolutionally

45

significant for microorganisms, increasing their survival.

46

Although advances in microscopy and molecular biological techniques have expanded our

47

understanding of metabolic processes in biofilms, the investigation of biofilm interaction with,

48

and resistance to toxic substances presents challenges. Characterization of both the structure and

49

chemistry of the biofilm is especially challenging since these may be modified in conventional

50

measurements. To address this, we employed a suite of complementary synchrotron-based

51

transmission and fluorescence imaging techniques using Se LIII and K near-edge X-ray

52

absorption spectroscopy to examine selenium biotransformation in multispecies biofilms. Our

53

novel approach using synchrotron-based hard and soft X-ray imaging techniques on the same

54

areas of the samples facilitated characterization of the chemistry of the accumulation and

55

biotransformation of the selenium in relation to the biological structures.

56

Our multispecies biofilms were cultured as previously20 using water sampled from a lentic

57

environment receiving effluent from a coal mine with elevated selenium levels.21 The biofilms

58

thus represent previously-characterized environmentally-relevant communities that have adapted

59

to cope with elevated levels of selenium. Our results show that specific regional communities

60

within the biofilms carry out selenium detoxification, as indicated by the localized distribution of

61

reduced selenium species. In particular, elemental selenium was found to be deposited as sub-

62

micron-sized particles closely associated with the microorganisms.

63 64

EXPERIMENTAL SECTION

65

Biofilm growth. Water for biofilm cultivation was collected as previously described by Yang

66

et al.20 from Goddard Marsh, British Columbia, Canada, a lentic environment receiving effluent 4 ACS Paragon Plus Environment

Page 5 of 32

Environmental Science & Technology

67

from a coal mine with high levels of selenium.21 The community of microorganisms was

68

previously reported20 to include the following selenium-resistant microorganisms: Rhodococcus

69

sp. (Gene Bank ID, AP0008957); Pseudomonas sp. (FJ652605.1); Bacillus sp. (GQ495047); and

70

Arthrobacter sp. (FJ517623.1). Biofilms were cultivated as described by Yang et al.20 with the

71

following modifications. The inoculum was 1 % of a microbial pre-culture incubated overnight

72

in 10 % tryptic soy broth (TSB) at room temperature (RT, 22 ± 3 °C). Biofilm growth occurred

73

on the surface of polycarbonate strips (10 cm × 1 cm) for 10 days or 1 month. Biofilms were

74

subsequently transferred to test tubes containing 16 mL of fresh 10 % TSB, which also contained

75

selenate or selenite (0.63 – 63 mM). Tubes were further incubated aerobically on a gyratory

76

incubator at 100 rpm for 20 days or 2 months. Thus, total incubation periods were 1 or 3 months.

77

The viability of the biofilms during this time period was verified by morphological examination

78

using confocal laser scanning microscopy, as previously described.20 All experimental

79

procedures were carried out in sterile conditions.

80

X-ray fluorescence imaging (XFI). Biofilm samples were rinsed at least 3 times using

81

autoclaved 10 % TSB, followed by removal of excess liquid. Biofilms were then harvested using

82

a sterile scraper made from silicon tubing. For each sample a 1 µL aliquot of the collected

83

biofilm was applied onto a silicon nitride window (0.5 mm × 0.5 mm, NX5050B, Norcada Inc,

84

AB, Canada) and allowed to air-dry. The prepared biofilm samples were brought to beamline 2-

85

ID-D of the Advanced Photon Source, USA. Regions of interest were recorded using an optical

86

light microscope (Leica DMR, Leica, IL, USA). The silicon nitride window was mounted onto

87

an aluminum frame positioned at 15° to the incident beam with a Vortex® silicon drift detector

88

(SII Nano Technology USA Inc., CA, USA) located at 90° to the incident beam to measure

89

fluorescence emission spectrum. The beam size was focused to 200 nm × 200 nm using a Fresnel 5 ACS Paragon Plus Environment

Environmental Science & Technology

Page 6 of 32

90

zone plate. The sample was maintained in a helium gas filled environment and raster scanned at

91

0.5 s per pixel. Data were processed using MAPS software.22 Further image processing was

92

conducted using the aXis2000 software.23 Co-localization maps of elements were processed

93

using the MAPS software.22 Mander’s overlap coefficients24 were calculated using macros

94

created in the Image J software.25

95

Determination of selenium concentration. To calibrate Se fluorescence emission from the

96

biofilm samples, X-ray fluorescence from a multi-element reference provided by National

97

Bureau of Standards26 was collected under the same geometrical configuration. Due to the thin

98

nature of the prepared biofilm samples (1~3 µm), thickness effects were disregarded. Among the

99

recorded Se concentrations, pixels having intensities less than 10 % of the maximum

100

concentration were disregarded in determining selenium concentration in both XFI and STXM

101

data. Following the usual XFI convention, Se concentrations are expressed in terms of the areal

102

density (µg/cm2) instead of a volume density (µg/cm3) since there is some uncertainty in the

103

thickness of the sample.

104

Sub-micron Se K-edge X-ray absorption spectroscopy. Se K near-edge X-ray absorption

105

spectra from the intense selenium spots were recorded using a 200 nm × 200 nm beam by

106

scanning energies from 12,620 to 12,740 eV in duplicate. Each spectrum was examined for any

107

photo-damage (oxidation or reduction) by checking for any spectral changes between duplicate

108

data collection scans. Spectra were processed using EXAFSPAK,27 and were compared with

109

spectra previously reported by Yang et al.20

110

Scanning transmission X-ray microscopy (STXM). STXM images and spectroscopy were

111

carried out at the Soft X-ray Spectromicroscopy beamline (SM) at the Canadian Light Source

112

(CLS). Data were collected using point, line scan, spectral, and whole scanning modes at a 6 ACS Paragon Plus Environment

Page 7 of 32

Environmental Science & Technology

113

sequence of energies and processed using the aXis2000 software.23,28 For the quantitative

114

analyses of selenium and biofilm macromolecular structures, singular value decomposition

115

(SVD)29 was used. Spectra of selenium references including selenate, selenite, selenomethionine,

116

selenocysteine, selenocystine, and elemental selenium were collected under the same conditions

117

and were used for quantitative analysis of selenium in biofilms. Carbon K-edges were collected

118

from 280 to 320 eV.28 Selenium LIII-edge spectra were collected from 1420 to 1470 eV. Spectra

119

from the carbon K and selenium L-edge were extracted, background subtracted, and normalized

120

to the highest absorbance points.

121 122

Transmission electron microscopy (TEM). TEM studies were carried out using Phillips CM 10 transmission electron microscope according to the method previously reported by Shi et al.30

123 124

RESULTS AND DISCUSSION

125

Elemental distribution in selenate-amended multispecies biofilms. We used synchrotron-

126

based X-ray fluorescence imaging (XFI) to examine the distribution of selenium and other

127

elements within the biofilms. Figure 1 shows examples of the images for different concentrations

128

of amended selenate or control, with fields of view corresponding to one or a few

129

microorganisms. We observed highly localized selenium in selenate-amended multispecies

130

biofilms incubated for three months with the highest concentration (63 mM) of selenate (Figure

131

1). These intense selenium spots, appearing as just one to two pixels across, are consistent with

132

highly concentrated selenium in objects of 400 nm diameter or less which are substantially

133

smaller than the cells; the lower limit on diameter is less than the 200 nm beamsize. The 6.3 mM

134

selenate treatment resulted in a peak selenium areal concentration which was three orders of

7 ACS Paragon Plus Environment

Environmental Science & Technology

Page 8 of 32

135

magnitude smaller than that of the 63 mM treatment (Table S1) and did not show evidence for

136

the highly localized selenium objects.

137

XFI allows the simultaneous measurement of distributions of other elements in the biofilm. Cu

138

and Zn were highly co-localized in certain regions of the biofilms. Mander's overlap coefficients

139

of Cu and Zn distribution images calculated for 0.63 and 63 mM selenate amended biofilms

140

(Figure 1) were 0.87 and 0.95, respectively (1 indicating the highest and 0 absence of overlap).

141

The morphologies of the Cu and Zn rich areas suggest that they are not distributed in the EPS,

142

but instead are restricted to cells. In contrast, P is evenly distributed throughout the biofilms. The

143

P distribution also differs from that of microbiologically important nonmetal elements S and Ca

144

which appear highly co-localized with each other (Mander’s overlap coefficients of 0.99 and

145

0.97 for 0.63 and 63 mM selenate-amended biofilms, respectively) and elevated in concentration

146

relative to the control (Table S1, Figure 1).

147

Elemental distribution in selenite amended multispecies biofilms. When multispecies

148

biofilms were incubated under selenite conditions (0.63 – 6.3 mM) for either 1 or 3 months

149

(Figure 2), we observed an elemental distribution pattern similar to that shown in selenate-

150

amended biofilms. However, in the case of selenite, the selenium concentrations were

151

considerably greater and more intensely localized within the biofilm (Figure 2, Table S1),

152

suggesting a highly concentrated phase. They also occurred at a much lower substrate

153

concentration (0.63 mM) compared with that for selenate (63 mM). Se K X-ray absorption near-

154

edge structure spectra measured with a sub-micron beam from these intense selenium spots

155

indicated that their chemical form is elemental selenium (Figure 3). This is consistent with our

156

observation of a red precipitate at the bottom of the bioreactors, suggesting that biofilms also

157

release elemental selenium particles into the environment. A consequence of the highly 8 ACS Paragon Plus Environment

Page 9 of 32

Environmental Science & Technology

158

concentrated selenium was that self-absorption distortions of the fluorescence signal caused a

159

reduction in intensity of the prominent 1s→4p transition (Figure 3). This intensity reduction was

160

more obvious in pt 2 and 3 than pt 1, which had much lower concentration. The relative

161

comparison, using spectral edge jump of the near-edge spectrum at each point, suggested pt 2

162

and 3 are 3.5 and 10.4 times more concentrated compared to pt 1. The relation between the

163

distortion in fluorescence signal and selenium particle size was previously simulated by

164

Wiramanaden et al.,31 with larger particle sizes of elemental selenium causing greatly decreased

165

fluorescence intensities of spectra at the peak compared with the edge jump.

166

The maximum concentration of selenium was substantially higher than those of other

167

biologically significant elements present in both selenite and selenate-amended biofilms. The

168

maximum concentration of the elemental selenium particles ranged from 14.7 to 301 µg/cm2 in

169

the examined biofilm areas (Figure 2, Table S1).

170

bioaccumulation as a consequence of bio-detoxification or utilization of selenite as an electron

171

acceptor by members of the multispecies biofilms.

This may suggest either selenium

172

Biotransformation of selenite to elemental selenium has been observed using conventional

173

analytical methods in many free-living microorganisms, such as Rhodospirillum rubrum,

174

Rhodobacter sphaeroides, Bacillus subtilis, Exiguobacterium sp, Rhizobium sp strain B1,

175

Pseudomonas sp. strain CA5, and Escherichia coli.32-37 However, there is limited information on

176

production of elemental selenium from selenite in complex multispecies biofilms. Indeed,

177

complex multispecies biofilms, which are inherently more challenging to characterize, likely

178

more closely represent how microbial consortia may cope with these toxic selenium oxyanions.

179

In general, selenite is more biochemically reactive than selenate in biofilms34-36 and thus

9 ACS Paragon Plus Environment

Environmental Science & Technology

Page 10 of 32

180

microorganisms may convert it to less reactive elemental selenium as a result of detoxification

181

and utilization.

182

Biotransformations of selenium oxyanions and biofilm macromolecular structure. We

183

used synchrotron-based scanning transmission X-ray microscopy (STXM) to investigate the

184

biotransformation products of selenium oxyanions and their possible associations with the

185

biofilm structures. STXM can specifically image for proteins, polysaccharides, and lipids that are

186

used respectively as markers for microbial cells, EPS and lipid in biofilms28,38 by using the

187

carbon K edge.39 In addition, imaging using the Se LIII-edges can give information about the

188

selenium distribution and speciation. Thus, information from STXM can be used to examine how

189

selenium oxyanions and their biotransformed species are associated with microbial cells and EPS

190

without the need for any physical or chemical modifications of biofilms.

191

The biofilm areas (Figure 4) that were initially investigated using XFI were subsequently

192

examined with STXM. Comparisons (Figure 4) between the selenium map (XFI) and the

193

elemental selenium/bio-macromolecule map (STXM-B) indicated that elemental selenium

194

particles are closely localized with microorganisms and tend to be deposited in biofilms. The

195

elemental selenium particles are seen to be surrounded by both microbial cells (protein) and EPS

196

(saccharide) (STXM-B), suggesting that the elemental selenium is embedded in the biofilm

197

structure. In an additional STXM map (Figure 5), the elemental selenium particles are again seen

198

to be associated with both EPS (green) and microbial cells (blue). Further investigation with least

199

square curve fitting of the observed Se LIII–edge spectrum in Figure 5 demonstrated that it is

200

indeed elemental selenium with less than 2 % error. Thus, our results clearly indicated that the

201

amended selenium oxyanions were biotransformed by the biofilms and that the majority of

10 ACS Paragon Plus Environment

Page 11 of 32

Environmental Science & Technology

202

selenium species present under the exposed incubation is the reduced product, elemental

203

selenium.

204

As shown in Figure 4, lipid (red, STXM-A) appeared to be closely associated with elemental

205

selenium (red, STXM-B), suggesting the coexistence and interaction of Se0 and lipid in highly

206

localized regions, although this observation may be complicated by the highly absorbing nature

207

of the dense elemental selenium particle. There have been a large number of reports on the role

208

of sulfur containing peptides or proteins in elemental selenium synthesis in vitro,37,40 but not on

209

the role of lipids. Although the reduction of selenium oxyanions can induce lipid peroxidation

210

through the generation of reactive oxygen species, it is not known whether the associated lipid

211

was oxidized during the reduction process of selenium oxyanions. However, the possible strong

212

association of lipid with elemental selenium may suggest that lipid is involved in the formation

213

and stabilization of elemental selenium in a similar fashion as thiol groups.37,41

214

Investigation of selenium chemical species using X-ray absorption spectroscopy.

215

Investigation of selenium chemical species using two synchrotron-based techniques on the same

216

areas of the biofilm demonstrated complementary and consistent results. In Figure 6, X-ray

217

absorption near-edge structure collected following XFI (Se K) and using STXM (Se LIII) from

218

selenium intense spots in biofilms both showed elemental selenium to be the intense selenium

219

species. Using STXM, selenium concentrations in the examined area were determined to be 152

220

and 62.9 µg/cm2 at maximum and average intensity, respectively. XFI on the same area, scanned

221

using the energy of the maximum intensity of the elemental selenium K absorption edge,

222

indicated 135 and 52.1 µg/cm2 at the most intense spot and at the average concentration,

223

respectively. Thus, the two methods provided results that were consistent and reproducible over

224

the investigated areas. 11 ACS Paragon Plus Environment

Environmental Science & Technology

Page 12 of 32

225

Biogenic selenium nanoparticles. Further investigation using transmission electron

226

microscopy (TEM) with selenite-treated biofilm sections of 70 nm thickness suggested the

227

presence of biogenic electron dense particles, consistent with the substantial presence of

228

elemental selenium. The electron dense particle sizes observed using TEM ranged from 50 to

229

700 nm in diameter, a size-range that including nanoparticles (Figure 7). Some electron-dense

230

particles were found inside of the cells although they were mostly within the EPS. This

231

distribution agrees with our observation of the locations of elemental selenium particles from

232

STXM (Figure 4 and Figure 6). Combining the results of XFI, STXM and TEM we conclude the

233

presence of elemental selenium particles, in the size range 50 to 700 nm, both inside cells and

234

also associated with the EPS. The association of selenium particles with EPS and the range of

235

particle sizes is consistent with the observations of Jain et al.42

236

In contrast, selenate-amended biofilms, similar to the control, lacked the high electron density

237

regions suggesting the absence of elemental selenium particles (Figure S2). This result agrees

238

with our XFI results (Figures 1 and 2) suggesting that the biotransformation of selenite is more

239

facile that that of selenate, since in the XFI the small particles of elemental selenium were

240

observed at high concentrations in treatment concentrations down to 0.63 mM selenite whereas

241

for selenate they were only apparent at 63 mM.

242

Complementarity of XFI and STXM. Here we have used two complementary synchrotron

243

X-ray methods – XFI and STXM – to provide information about the multispecies biofilms.

244

STXM typically measures the absorption of the sample in transmission, although fluorescence

245

detection increasingly is available.43 Transmission is ideal for locally concentrated species, such

246

as the elemental selenium particles observed in this study. By measuring stacks of images using a

247

series of energies across the Se LIII-edge, chemical information on Se for the entire image can be 12 ACS Paragon Plus Environment

Page 13 of 32

Environmental Science & Technology

248

obtained. In addition, measuring the C K-edge energy range of the same area allows the

249

identification of biological moieties (bacterial cells, EPS and lipid), enabling the Se particles to

250

be localized with respect to the biofilm structures. XFI measures the fluorescent photons44 and

251

typically works at higher X-ray energies than STXM. Instrumentally, good spatial resolution is

252

easier to obtain at low X-ray energies and thus hard X-ray XFI generally has poorer spatial

253

resolution than STXM. Conversely, hard X-ray XFI typically can detect much more dilute

254

species per pixel than can STXM, since fluorescence yield is higher for K-edges than for L-edges

255

as well as increasing with atomic number.45 In addition, Se XFI allows the simultaneous

256

measurement of the distributions of metals and other elements with absorption edges below that

257

of the Se K-edge (Figures 1 and 2), and is useful for scanning a wider area of the sample than is

258

feasible using STXM. Following collection of XFI maps, X-ray absorption spectroscopy at select

259

pixels can provide information on the Se chemical form. Alternatively, by tuning the incident

260

energy to characteristic features in the near-edge, maps of individual Se chemical forms can be

261

generated.46 Together, STXM and XFI provide complementary probes of complex multispecies

262

biofilms.

263

Any method that uses ionizing radiation runs the risk of sample damage, and both XFI and

264

STXM have potential to damage samples. In our case XFI measurements were conducted first

265

and STXM second. One reason for this order was that XFI is better suited for range-finding than

266

XFI, in that it maps a larger spatial area much more quickly than STXM. Moreover, the higher

267

energy X-rays of the XFI measurement have more than four orders of magnitude lower X-ray

268

mass absorption coefficient since they are more penetrating and result in a lower radiation dose

269

to the sample than lower energy X-rays. Hence, at the lower energies of the C K-edge used on

270

STXM, the beam is strongly absorbed making radiation damage more likely. Thus, we employed 13 ACS Paragon Plus Environment

Environmental Science & Technology

Page 14 of 32

271

high energy XFI first followed by low energy STXM to minimized both damage to biofilms and

272

photoreduction of selenium oxyanions. Since photoreduction of selenium oxyanions can be quite

273

facile,47 the effects of beam damage would appear earliest in the Se K near-edge spectra of these

274

species. Thus, we investigated possible photo-damage of selenium species by collecting multiple

275

Se K-edge spectra from spots of selenate and selenite powder samples, and observed no

276

significant changes (Figure S1). This demonstrates that our methodology, of XFI followed by

277

STXM, minimizes photo-damage and allows correlative measurements to be made on the same

278

sample. If samples had sustained substantial damage from exposure to X-rays during the XFI

279

then, as previously reported,48 STXM should show the formation of peaks at 285 and 286.6 eV

280

(ketones and phenols) and substantially reduced lipid, polysaccharide and protein features. This

281

was not observed in our data, and we therefore feel reasonably confident that the samples were

282

relatively damage free at the start of the STXM experiment, but such damage cannot be

283

rigorously excluded at the time of writing. In any case, this novel combination of methods may

284

be useful for other research in microbiology and cell biology for example, in which tools with

285

high spatial resolution and chemical sensitivity with minimal sample destruction would be an

286

asset.

287

Environmental implications. While the accumulation of elemental selenium particles has

288

been observed in planktonic forms of pure bacterial cultures,32-37 our work demonstrates this

289

process for complex multispecies biofilms. We have achieved this using a suite of

290

complementary synchrotron-based tools, which are widely applicable to other biofilm and

291

cellular-level structures of environmental relevance. The reduction of selenium to low solubility

292

elemental selenium may suggest that such multispecies biofilms represent a pathway for

293

sequestration of selenium as a low bioavailability form and even for bioremediation of selenium 14 ACS Paragon Plus Environment

Page 15 of 32

Environmental Science & Technology

294

contaminated areas, such as mine impacted sites. In support of this, elemental selenium, likely

295

produced by multispecies biofilms, was observed as a significant component of selenium present

296

in sediments near uranium mining and milling operations.12,31 However, caution is warranted

297

since nanoparticles have different properties compared with the bulk form48 and synthetic

298

elemental selenium nanoparticles have been observed to be highly bioavailable to benthic

299

invertebrates.50 Moreover, biogenic selenium nanoparticles have been reported to show

300

antimicrobial activity in effectively inhibiting biofilm formation in other microbes,51

301

demonstrating that elemental selenium nanoparticles are not inert. Here we observe that the

302

elemental selenium nanoparticles are intimately associated with the microbial cells and EPS

303

component of the multispecies biofilm. This association may modify both the stability of the

304

nanoparticles and their bioavailability in the environment.

305 306

ASSOCIATED CONTENT

307

Supporting Information.

308

Maximum and average areal elemental concentrations in multispecies biofilms (Table S1),

309

selenium K near-edge spectra of powdered selenate and selenite as a function of time of

310

irradiation (Figure S1), and TEMs of control and selenate-amended biofilms (Figure S2). The

311

Supporting Information is available free of charge on the ACS Publications website at DOI:

312

10.1021/acs.est.xxxxxxx.

313 314

AUTHOR INFORMATION

15 ACS Paragon Plus Environment

Environmental Science & Technology

315

Corresponding Author

316

*Phone: 306-966-5706; fax: 306-966-5683; e-mail: [email protected].

317

Notes

318

The authors declare no competing financial interest.

Page 16 of 32

319 320 321

ACKNOWLEDGMENTS

322

The authors thank members of the Pickering/George group at the University of Saskatchewan

323

and George Swerhone at Environment Canada. This research is supported by a Natural Sciences

324

and Engineering Research Council of Canada (NSERC) Discovery Grant (to Pickering), by

325

Saskatchewan Innovation and Science Fund (to Pickering) and by Environment Canada.

326

Pickering and George are Canada Research Chairs and Yang is a CIHR-THRUST Fellow. The

327

Canadian Light Source is supported by the Canada Foundation for Innovation, NSERC, the

328

University of Saskatchewan, the Government of Saskatchewan, Western Economic

329

Diversification Canada, the National Research Council Canada, and the Canadian Institutes of

330

Health Research. Use of the Advanced Photon Source, an Office of Science User Facility

331

operated for the U.S. Department of Energy (DOE) Office of Science by Argonne National

332

Laboratory, was supported by the U.S. DOE under Contract No. DE-AC02-06CH11357.

REFERENCES

16 ACS Paragon Plus Environment

Page 17 of 32

Environmental Science & Technology

1. Letavayová, L.; Vlasáková, D.; Spallholz, J. E.; Brozmanová, J.; Chovanec, M. Toxicity and mutagenicity of selenium compounds in Saccharomyces cerevisiae. Mutat. Res. 2008, 638, 1–10. 2. Brown, K.; Arthur, J. Selenium, selenoproteins and human health: a review. Public Health Nutr. 2001, 4, 593–599. 3. Hartikainen, H.; Xue, T.; Piironen, V. Selenium as an anti-oxidant and pro-oxidant in ryegrass. Plant Soil 2000, 225, 193–200. 4. Pedrero, Z.; Madrid, Y.; Hartikainen, H.; Cámera, C. Protective effect of selenium in broccoli (Brassica oleracea) plants subjected to cadmium exposure. J. Agric. Food Chem. 2008, 56, 266–271. 5. Renwick, A. G. Toxicology of micronutrients: adverse effects and uncertainty. J. Nutr. 2006, 136, 493S–501S. 6. Sekowska, A.; Kung, H.; Danchin, A. Sulfur metabolism in Escherichia coli and related bacteria: facts and fiction. J. Mol. Microbiol. Biotechnol. 2000, 2, 145–177. 7. Miklós Mézes, K. B. Prooxidant mechanisms of selenium toxicity – a review. Acta Biologica Szegediensis 2009, 53, 15–18. 8. Lemly, A. D. Aquatic selenium pollution is a global environmental safety issue. Ecotox. Environ. Safe. 2004, 59, 44–56. 9. Hamilton, S. J. Review of selenium toxicity in the aquatic food chain. Sci. Total Environ. 2004, 326, 1–31.

17 ACS Paragon Plus Environment

Environmental Science & Technology

Page 18 of 32

10. Young, T.F.; Finley, K.; Adams, W. J.; Besser, J.; Hopkins, W. D.; Jolley, D.; McNaughton, E.; Presser, T. S.; Shaw, D. P.; Unrine, J. Appendix A: Selected case studies of ecosystem contamination by Se. In: Ecological assessment of selenium in the aquatic environment; Chapman, P.M., Adams, W. J., Brooks, M. L., Delos, C. G., Luoma, S. N., Maher, W. A., Ohlendorf, H. M., Presser, T. S., Shaw, D. P., Eds.; CRC Press: Boca Raton (FL) 2010; pp 257–292. 11. Stewart, R.; Grosell, M.; Buchwalter, D.; Fisher, N.; Luoma, S. N.; Mathews, T.; Orr, P.; Wang, X. W. Bioaccumulation and trophic transfer of selenium. In: Ecological assessment of selenium in the aquatic environment; Chapman, P.M., Adams, W. J., Brooks, M. L., Delos, C. G., Luoma, S. N., Maher, W. A., Ohlendorf, H. M., Presser, T. S., Shaw, D. P., Eds.; CRC Press: Boca Raton (FL) 2010; pp 93–139. 12. Janz, D. M.; Liber, K.; Pickering, I. J.; Wiramanaden, C. I. E.; Weech, S. A.; GallegoGallegos, M.; Driessnack, M. K.; Franz, E. D.; Goertzen, M. M.; Phibbs, J.; Tse, J. J.; Himbeault, K. T.; Robertson, E. L.; Burnett-Seidel, C.; England K.; Gent, A. Integrative assessment of selenium speciation, biogeochemistry and distribution in a northern coldwater ecosystem. Integr. Environ. Assess. Manag. 2014, 10, 543–554. 13. Ohlendorf, H. M.; Hoffman, D. J.; Saiki, M. K.; Aldrich, T. W. Embryonic mortality and abnormalities of aquatic birds: Apparent impacts of selenium from irrigation drainwater. Sci. Total Environ. 1986, 52, 49–63. 14. Lemly, A.D. Teratogenic effects of selenium in natural populations of fresh water fish. Ecotox. Environ. Safe. 1993, 26, 181–204.

18 ACS Paragon Plus Environment

Page 19 of 32

Environmental Science & Technology

15. Janz, D. M. Selenium. In: Homeostasis and Toxicology of Essential Metals (Fish Physiology series, Vol. 31A); Wood, C. M., Farrell, A. P., Brauner, C. J., Eds.; Elsevier: San Diego 2012; pp 327−374. 16. van Hullebusch, E.; Zandvoort, M.; Lens, P. Metal immobilisation by biofilms: mechanisms and analytical tools. Rev. Environ. Sci. Biotechnol. 2003, 2, 9–33. 17. Lawrence, J. R.; Neu, T. R. Microscale analyses of the formation and nature of microbial biofilm communities in river systems. Rev. Environ. Sci. Biotechnol. 2003, 2, 85–97. 18. Koechler, S.; Farasin, J.; Cleiss-Arnold, J.; Arsène-Ploetze, F. Toxic metal resistance in biofilms: diversity of microbial responses and their evolution. Res. Microbiol. 2015, 166, 764–773. 19. Waters, C. M.; Bassler, B. L. Quorum Sensing: Cell-to-cell communication in bacteria. Annu. Rev. Cell Dev. Biol. 2005, 21, 319–346. 20. Yang, S. I.; Lawrence, J. R.; Swerhone, G. D. W.; Pickering, I. J. Biotransformation of selenium and arsenic in multi-species biofilm. Environ. Chem. 2011, 8, 543–551. 21. Orr, P. L.; Karin R. Guiguer, K. R.; Cynthia K. Russel, C. K. Food chain transfer of selenium in lentic and lotic habitats of a western Canadian watershed. Ecotox. Environ. Safe. 2006, 63, 175–188. 22. Vogt, S. MAPS: A set of software tools for analysis and visualization of 3D X-ray fluorescence data sets. J. Phys. IV France 2003, 104, 635–638.

19 ACS Paragon Plus Environment

Environmental Science & Technology

Page 20 of 32

23. Hitchcock, A. P. (2010) aXis2000 is written in interactive data language (IDL) and available at http://unicorn.mcmaster.ca/aXis2000.html 24. Manders, E. M. M.; Verbeek, F. J.; Aten, J. A. Measurement of co-localization of objects in dual-colour confocal images. J. Microscopy 1993, 169, 375–382. 25. Abramoff, M. D.; Magelhaes, P. J.; Ram, S. J. Image processing with Image J. Biophoton. Int. 2004, 11, 36–42. 26. Pella, P. A.; Newbury, D. E.; Steel, E. B.; Blackburn, D. H. Development of National Bureau of Standards thin glass films for x-ray fluorescence spectrometry. Anal. Chem. 1986, 58, 1133–1137. 27. George, G. N.; Pickering, I. J. (2001) EXAFSPAK: A suite of computer programs for analysis

of

X-ray

absorption

spectra

available

at

http://ssrl.slac.stanford.edu/exafspak.html 28. Dynes, J. J.; Tyliszczak, T.; Araki, T.; Lawrence, J. R.; Swerhone, G. D. W.; Leppard, G. G.; Hitchcock, A. P. Speciation and quantitative mapping of metal species in microbial biofilms using scanning transmission X-ray microscopy. Environ. Sci. Technol. 2006, 40, 1556–1565. 29. Koprinarov, I. N.; Hitchcock, A. P.; McCrory, C. T.; Childs, R. F. Quantitative mapping of structured polymeric systems using singular value decomposition analysis of soft X-ray images. J. Phys. Chem. B 2002, 106, 5358–5364.

20 ACS Paragon Plus Environment

Page 21 of 32

Environmental Science & Technology

30. Shi, C.; Kendall, S. C.; Grote, E.; Kaminskyj, S.; Loewen, M. C. N-terminal residues of the yeast pheromone receptor, Ste2p, mediate mating events independently of G1-arrest signaling. J. Cell Biochem. 2009, 107, 630–638. 31. Wiramanaden, C. I. E.; Liber, K.; Pickering, I. J. Selenium speciation in whole sediment using X-ray absorption spectroscopy and micro X-ray fluorescence imaging. Environ. Sci. Technol. 2010, 44, 5389–5394. 32. Kessi, J.; Ramuz, M.; Wehrli, E.; Spycher, M.; Bachofen, R. Reduction of selenite and detoxification of elemental selenium by the phototrophic bacterium Rhodospirillum rubrum. Appl. Environ. Microbiol. 1999, 65, 4734–4740. 33. Van Fleet-Stalder, V.; Chasteen, T. G.; Pickering, I. J.; George, G. N.; Prince, R. C. Fate of selenate and selenite metabolized by Rhodobacter sphaeroides. Appl. Environ. Microbiol. 2000, 66, 4849–4853. 34. Ikram, M.; Faisal, M. Comparative assessment of selenite (SeIV) detoxification to elemental selenium (Se0) by Bacillus sp. Biotechnol. Lett. 2010, 32, 1255–1259. 35. Hunter, W.; Kuykendall, L. Reduction of selenite to elemental red selenium by Rhizobium sp. strain B1. Curr. Microbiol. 2007, 55, 344–349. 36. Hunter, W.; Manter, D. Reduction of selenite to elemental red selenium by Pseudomonas sp. strain CA5. Curr. Microbiol. 2009, 58, 493–498. 37. Dobias, J.; Suvorova, E. I.; Bernier-Latmani, R. Role of proteins in controlling selenium nanoparticle size. Nanotechnology 2011, 22, 195605.

21 ACS Paragon Plus Environment

Environmental Science & Technology

Page 22 of 32

38. Lawrence, J. R.; Swerhone, G. D. W.; Leppard, G. G.; Araki, T.; Zhang, X.; West, M. M.; Hitchcock, A. P. Scanning transmission X-ray, laser scanning, and transmission electron microscopy mapping of the exopolymeric matrix of microbial biofilms. Appl. Environ. Microbiol. 2003, 69, 5543–5554. 39. Brandes, J. A.; Lee, C.; Wakeham, S.; Peterson, M.; Jacobsen, C.; Wirick, S.; Cody, G. Examining marine particulate organic matter at sub-micron scales using scanning transmission X-ray microscopy and carbon X-ray absorption near edge structure spectroscopy. Mar. Chem. 2004, 92, 107–121. 40. Zhang, J.; Gao, X. G.; Zhang, L.; Bao, Y. Biological effects of a nano red elemental selenium. Biofactors 2001, 15, 27–38. 41. Ogasawara, Y.; Lacourciere, G.; Stadtman, T. C. Formation of a selenium-substituted rhodanese by reaction with selenite and glutathione: Possible role of a protein perselenide in a selenium delivery system. Proc. Natl. Acad. Sci. USA 2001, 98, 9494– 9498. 42. Jain, R.; Jordan, N.; Weiss, S.; Foerstendorf, H.; Heim, K.; Kacker, R.; Hübner, R.; Kramer, H.; van Hullebusch, E. D.; Farges, F.; Lens, P. N. L. Extracellular polymeric substances govern the surface charge of biogenic elemental selenium nanoparticles. Environ. Sci. Technol. 2015, 49, 1713−1720. 43. Hitchcock, A. P.; Obst, M.; Wang, J.; Lu, Y. S.; Tyliszczak, T. Advances in the detection of As in environmental samples using low energy X-ray fluorescence in a

22 ACS Paragon Plus Environment

Page 23 of 32

Environmental Science & Technology

scanning transmission X-ray microscope: Arsenic immobilization by an Fe(II)oxidizing freshwater bacteria. Environ. Sci. Technol. 2012, 46, 2821–2829. 44. Pushie, M. J.; Pickering, I. J.; Korbas, M.; Hackett, M. J.; George, G. N. Elemental and chemically specific X-ray fluorescence imaging of biological systems. Chem. Rev. 2014, 114, 8499–8541. 45. Hubbell, J. H.; Trehan, P. N.; Singh, N.; Chand, B.; Mehta, D.; Garg, M. L.; Garg, R. R.; Singh, S.; Purl, S.A Review, bibliography, and tabulation of K, L, and higher atomic shell X-ray fluorescence yields. J. Chem. Phys. Ref. Data 1994, 23, 339–364. 46. Pickering, I. J.; Prince, R. C.; Salt, D. E.; George, G. N. Quantitative, chemically specific imaging of selenium transformation in plants. Proc. Natl. Acad. Sci. 2000, 97, 10717–10722. 47. George, G. N.; Pickering, I. J.; Pushie, M. J.; Nienaber, K.; Hackett, M. J.; Ascone, I.; Hedman, B.; Hodgson, K. O.; Aitken, J. B.; Levina, A.; Glover, C.; Lay, P. A. X-rayinduced photo-chemistry and X-ray absorption spectroscopy of biological samples. J. Synch. Radiat. 2012, 19, 875–886. 48. Gillespie, A. W.; Phillips, C. L.; Dynes, J. J.; Chevrier, D.; Regier, T. Z.; Peak, D. Advanced in using soft X-ray spectroscopy for measurements of soil biogeochemical processes. Adv. Agron. 2015, 133, 1-32. 49. Buzea, C.; Pacheco, I. I.; Robbie, K. Nanomaterials and nanoparticles: Sources and toxicity. Biointerphases 2007, 2, MR17–MR71.

23 ACS Paragon Plus Environment

Environmental Science & Technology

Page 24 of 32

50. Gallego-Gallegos, M.; Doig, L. E.; Tse, J. J.; Pickering, I. J.; Liber, K. Bioavailability, toxicity and biotransformation of selenium in midge (Chironomus dilutus) larvae exposed via water or diet to elemental selenium particles, selenite, or selenized algae. Environ. Sci. Technol. 2013, 47, 584–592. 51. Zonaro, E.; Lampis, S.; Turner, R. J.; 2, Qazi, S. J. S.; Vallini, G. Biogenic selenium and tellurium nanoparticles synthesized by environmental microbial isolates efficaciously inhibit bacterial planktonic cultures and biofilms. Front. Microbiol. 2015, 6, 584.

24 ACS Paragon Plus Environment

Page 25 of 32

Environmental Science & Technology

Figure 1. False color micro-XFI elemental distribution maps for biofilms grown for 3 months in the presence of 0 (Se-free control), 6.3 and 63 mM selenate. Incident energy was 12,680 eV. Left panels show optical microscopic images of the scanned areas. Scale bars show 2 μm. The false color scale represents concentrations, with the maximum for each panel shown in Table S1.

ACS Paragon Plus Environment

25

Environmental Science & Technology

Page 26 of 32

Figure 2. False color micro-XFI elemental distribution maps for biofilms grown for 3 months in the presence of 0.63 mM selenite, and 1 month and 3 months in the presence of 6.3 mM selenite. Incident energy was 12,680 eV. Left panels show optical microscopic images of the scanned areas. Scale bars show 2 μm. The false color scale represents concentrations, with the maximum for each panel shown in Table S1.

ACS Paragon Plus Environment

26

Page 27 of 32

Environmental Science & Technology

Figure 3. Selenium distribution in biofilm (left) incubated for 1 month under 6.3 mM of selenite. The scale bar shows 2 μm and the selenium intensity bar is shown at the bottom of the image. Normalized Se K near-edge spectra (right) from 200 nm spots as indicated by pt 1 to pt 3, in comparison with reference spectra of selenite and elemental selenium (Se0). The broken line indicates the peak position of elemental selenium.

ACS Paragon Plus Environment

27

Environmental Science & Technology

Page 28 of 32

Figure 4. Optical, XFI and STXM images of the same areas of biofilms treated with selenite at 0.63 mM for 3 months (also shown in Figure 2), and at 6.3 mM for 1 and 3 months. XFI results show the upper 90 % and lower 10 % of the selenium intensity in red and green, respectively. STXM-A shows tricolor maps of the distribution of lipid (Lpd, red), polysaccharide indicating EPS (Psd, green) and protein showing bacterial cells (Prt, blue). STXM-B combines elemental selenium (Se0, red) with macromolecular distributions of EPS (Psd, green) and microbial cells (Prt, blue). The areas were investigated by XFI followed by STXM. Scale bars indicate 1 μm.

ACS Paragon Plus Environment

28

Page 29 of 32

Environmental Science & Technology

Figure 5. STXM image (left) and observed selenium LIII-edge spectra (right) from biofilm amended with 6.3 mM selenite for 1 month. The STXM image shows elemental selenium (red), extracellular polymeric substances modelled as polysaccharide (green), and microbial cells modelled as protein (blue). Scale bar indicates 1 μm. The yellow broken line outlines the region from which the observed spectrum was extracted. The least square fitting result of the observed spectrum to an elemental selenium standard is shown as a dotted line.

ACS Paragon Plus Environment

29

Environmental Science & Technology

Page 30 of 32

Figure 6. XFI and STXM images (left) of biofilm amended with 6.3 mM selenite for 1 month. The same area of biofilm was investigated by XFI followed by STXM. Scale bars indicate 1 μm. XFI image shows selenium distribution on a relative intensity scale (white = high). STXM tricolor image shows selenium (red), protein (blue) and polysaccharide (green). Se X-ray absorption spectra (right) of the biofilm are compared with spectra of selenite and elemental selenium (Se0) standards, showing good correspondence with the latter. Nano Se K X-ray absorption near-edge spectra (upper right), were recorded from pt 1 and pt 2 in the XFI image. The “Intense” Se LIII near-edge spectrum (lower right) was extracted from the areas of intense selenium shown in red in the STXM image. The dotted lines indicate the peak position of elemental selenium.

ACS Paragon Plus Environment

30

Page 31 of 32

Environmental Science & Technology

Figure 7. Thin sectioned (70 nm) transmission electron micrographs of biofilms amended with 6.3 mM (a) and 63 mM selenite (b) for 3 months. Electron dense areas shown in black suggest elemental selenium nanoparticles. Scale bars indicate 0.5 μm.  

ACS Paragon Plus Environment

31

Environmental Science & Technology

Page 32 of 32

TOC Graphic

ACS Paragon Plus Environment

32