Nitrogen-Rich Conjugated Microporous Polymers: Facile Synthesis

BS8 1TS, U.K.. ACS Appl. Mater. Interfaces , 2017, 9 (44), pp 38390–38400. DOI: 10.1021/acsami.7b09553. Publication Date (Web): October 18, 2017...
3 downloads 13 Views 3MB Size
Subscriber access provided by Gothenburg University Library

Article

Nitrogen-rich conjugated microporous polymers: facile synthesis, efficient gas storage and heterogeneous catalysis Yaozu Liao, Zhonghua Cheng, Weiwei Zuo, Arne Thomas, and Charl F.J. Faul ACS Appl. Mater. Interfaces, Just Accepted Manuscript • DOI: 10.1021/acsami.7b09553 • Publication Date (Web): 18 Oct 2017 Downloaded from http://pubs.acs.org on October 18, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

ACS Applied Materials & Interfaces is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 23

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Nitrogen-Rich Conjugated Microporous Polymers: Facile Synthesis, Efficient Gas storage and Heterogeneous Catalysis Yaozu Liao,*,1,2,3 Zhonghua Cheng,1 Weiwei Zuo,1 Arne Thomas*,2 Charl F. J. Faul*,3 1

State Key Laboratory for Modification of Chemical Fibers and Polymer Materials & College of Materials Science and Engineering, Donghua University, Shanghai 201620, China 2 Department of Chemistry and Functional Materials, Technische Universität Berlin, Berlin 10623, Germany 3 School of Chemistry, University of Bristol, Bristol, England BS8 1TS, UK

*Corresponding authors: [email protected]; [email protected]; [email protected]

Abstract: Nitrogen-rich conjugated microporous polymers (NCMPs) have attracted great attention in recent years owing to their polarity, basicity, and ability to coordinate metal ions. Herein three NCMPs, structurally close to polyaniline, were facilely synthesized via chemical oxidative polymerization between multi-connected aniline precursors. The NCMPs with high N content (11.84 wt%), intrinsic ultramicroporosity (94% activity in Suzuki–Miyaura coupling reactions after six continuous runs. Keywords: Conjugated microporous polymers, polyaniline, gas storage, catalysis, synthesis

Introduction Conjugated microporous polymers (CMPs) with small pores ( NCMP2 > NCMP3, which is well consistent with the amount of residual HCl. When heated to 900

o

C, the highly cross-linked NCMPs maintained 55-69 wt%

carbonaceous residues, which is in contrast to conventional polyaniline yielding no carbonaceous residue.

5

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 2 (a-c) SEM and (d-i) TEM images of (a,d,g) NCMP1, (b,e,h) NCMP2 and (c,f,i) NCMP3 networks at low (d-f) and high (g-i) magnifications.

Microporosity of the NCMPs was confirmed by N2 adsorption measurements. NCMP1, NCMP2, and NCMP3 (Figure 1d) reveal Brunauer−Emmett−Teller (BET) surface areas of 58, 280, and 485 m2 g-1, total pore volumes of 0.15, 0.30, and 0.57 cm3 g-1 at a relative pressure of p/p0 = 0.994, and micropore volumes of 0.06, 0.09, and 0.13 cm3 g-1, respectively (Table 1). On the basis of the N2 adsorption isotherms, the NCMPs possess small micropores with sizes below 1 nm as determined by the nonlocal density functional theory (NLDFT) method (Figure 1e). As discussed above, the NCMP networks mainly consist of the triphenylamine (NPh3) moiety, known as a hole-transporting material for organic electroluminescent devices,39 as well as an important tecton yielding high surface area CMPs.21,40,41 Applying our NCMPs for gas storage and as catalytic support is therefore worthy of exploration. All NMCPs exhibit CO2 storage capability (Figure 3a,b and Table 1), with NCMP3 showing the highest CO2 uptake capacity (11 wt%, 2.50 mmol g-1) at 1 bar and 273 K. The CO2 uptake capacity obtained is comparable or even superior to that of many porous materials including polyaniline@MIL-101 (40 kJ mol-1),55 implying strong physical interactions between adsorbed CO2 and the functional pore surface. Moreover, the NCMPs show H2 storage capacities up to 1.02 wt% at 77 K and 1.0 bar (for example, NCMP3) (Figure S12), which is higher than the values obtained for most porous polymer networks,56,57 for example, a recent report on porous hypercrosslinked polymers showed H2 storage capacities of 1.01 wt% (77 K and 1.13 bar).57 Again, on the basis of the Clausius-Clapeyron equation,58 initial Qst values for H2 adsorption in NCMP1 is calculated as high as 8.3 kJ mol-1 (Figure S13). This value is higher than that of other porous organic polymers such as of PAF-1 (4.6 kJ mol-1),59 PIs (5.3-7.0 kJ mol-1),60 COFs (6.0-7.0 kJ mol-1),61-63 further suggesting a favorable physical interaction between adsorbed H2 and the porous surface.64 Table 1 Summaries of physiochemical properties of NCMPs. Polymer

SBETa

(m2/g)

VTb

Vmicroc

N%d

CO2 uptake

H2 uptake

at 1 bar (wt%)

at 1 bar (wt%)

298 K

77 K

87 K

(cm3/g)

(cm3/g)

(wt%)

273 K

NCMP1

58

0.15

0.06

11.84

6.1

3.5

0.68

0.49

NCMP2

280

0.30

0.09

10.14

8.2

4.4

0.79

0.54

NCMP3

485

0.57

0.13

7.39

11.0

6.5

1.02

0.68

a

calculated using a multi-point BET method; bcalculated based on N2 adsorption at p/p0 = 0.994;

c

calculated using a MP method; drelative content measured by EDX.

In addition to CO2 and H2 storage, we also explored the NCMP networks for their potential application in iodine adsorption. Iodine vapor adsorption is of particular interest, since the long-lived radioactive iodine isotopes (e.g. 129I or 131I) need to be removed from exhaust fumes of 8

ACS Paragon Plus Environment

Page 9 of 23

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

nuclear power plants regularly.65 Previous studies showed that nitrogen-containing CMPs are promising to address this issue.20 Upon exposure to iodine vapor at 1 bar and 358 K, porous NCMPs became gradually darker as iodine molecules diffused into the porous networks. Equilibrium adsorption is found to be 215, 186, and 161 wt% for NCMP1, NCMP2, and NCMP3, respectively. It is well known that electron-deficient iodine (acceptor) interacts with electron-rich adsorbents (donor), giving rise to charge transfer from the HOMO of the donor to the LUMO of the acceptor. Previous studies suggest that the charge-transfer interactions are responsible for the high iodine adsorption capacity of aniline-linked hexaphenylbenzene-based conjugated microporous polymer (HCMP) adsorbents.20 The NCMPs showed a slightly smaller main pore size than the molecular diameter of iodine (0.57 vs. 0.60 nm), as determined by the nitrogen adsorption isotherms at 77 K. We believe that the combination of nitrogen content and HOMO energy of the NCMPs (both which influence the electron-donor ability) may preferentially direct the iodine adsorption capacity rather than surface area and pore size (determined by nitrogen adsorption at 77 K).66 We used P1, P2, and P3 as model compounds to monitor the HOMO energy of corresponding polymers on the basis of calculations at the B3LYP/6-31G (d) level with Gaussian 09 software.38 NCMP1, with the highest nitrogen content, shows the highest HOMO energy (Table S9), which fits very well with the highest iodine adsorption capacity observed. Actual measurements of HOMO-LUMO band gaps for polymers were carried out using cyclic voltammetry (Figure S14) and UV-vis absorption scans (Figure 1c). The HOMO-LUMO band gaps (Eg) of NCMP1, NCMP2, and NCMP3 were calculated on the basis of the wavelengths at maximal UV-vis absorption (λmax) according to the equation: Eg = 1240/λmax, giving values for Eg = 1.22, 1.17, and 1.54 eV, respectively. The results indicate that the electron-donating ability follows the order: NMCP2 > NCMP1 >> NCMP3, which is also seen in the strongest redox activity of NCMP2 according to cyclic voltammetry measurements (Figure S14). Previous studies showed that reduction and oxidization of secondary amine-linked HCMPs resulted in better iodine and CO2 uptake capacities,20 respectively. Owing to the similar molecular architectures of HCMPs and NCMPs, this conclusion should be also applicable to the NCMPs if the residual secondary amine moieties are mostly preserved. However, in stark contrast to the HCMP behavior reported before, the FT-IR spectra of NCMP2 showed negligible changes except 9

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 10 of 23

for a weak peak at 1630 cm-1 which is slightly increased when oxidized by H2O2 or iodine and reduced by anhydrous hydrazine (Figure S15), respectively. This peak may be attributed to the small fraction of quinones existing in the conjugated polymer, which are sensitive to oxidation and reduction. The results indicate that a more stable structure is obtained for NCMPs compared to HCMPs. This is also supported by the negligible changes observed in the

13

C NMR spectra of

NCMP2 upon oxidization and reduction (Figure S16). The treated porous polymers showed very small deviations in CO2 and iodine uptake capacities (Figs. S17 and Table S9). Meanwhile, five-point N2 adsorption measurements indicated that only a small decrease of surface area observed in NCMP2 upon oxidization (256 vs. 280 m2/g) is observed. These results prove that the small fraction of residual secondary amines, inevitably left in the polymers due to incomplete polymerization during network formation, are not sufficient to enable a polyaniline-like switching behavior. It can thus be concluded that the majority of secondary amines of the precursors has been converted into tertiary amines after polymerization. This is further confirmed by the finding that no methylene groups are detectable in NCMPs upon further reaction using diiodomethane as a cross-linker (note that such a cross-linking method has been well-developed for the leucoemeraldine base state of polyaniline30). Considering the polymers were purified using concentrated acid (35 wt% HCl) and hot water (75 oC) overnight, the results further indicate their high physicochemical stability. Furthermore, NCMP networks with abundant tertiary nitrogen moieties possess the potential to coordinate metal ions and act as catalyst support. In an initial, proof-of-concept study, palladium dichloride (PdCl2) was coordinated to NCMP2 (as NCMP1 and NCMP3 have either a lower specific surface area or lower nitrogen content, and were therefore not considered for this initial study). After PdCl2 was introduced, NCMP2 showed a significant decrease in surface area from 280 to 26 m2/g due to the weight gained by introducing Pd species and mainly pore blocking or so. Successful coordination was confirmed by ICP-AES, XRD, and XPS analyses as well as SEM and TEM observations. ICP-AES results showed that 11.8 wt% Pd (theoretical content: 21.3 wt%) and no Fe were present in the network structure. The XRD pattern of NCMP2-PdCl2 shows four additional crystal reflections at 2θ = 39.9, 46.5, 68.2, and 82.0o (Figure 4a) owing to palladium particles,67 indicating that the PdCl2 introduced was partially reduced to Pd(0). It has been 10

ACS Paragon Plus Environment

Page 11 of 23

reported that electron-rich conjugated polymers with high N-content are able to reduce noble metal ions into metallic particles,68 which seem to be the case also here. The XPS spectra confirm that C, N, Cl, Pd, and O are present in the NCMP2-PdCl2 (Figure 4b). The O peak is possibly indicative of readily adsorbed oxygen or water, which is normally found in porous materials.69 The Pd3d core-level XPS spectrum in Figure 5b shows two broad peaks at 337.2 and 342.4 eV, suggesting the existence of both Pd(0) and Pd(II) in the catalyst.70,71 The result is consistent with that of recently reported Pd, N, P, and O-doped porous polymer catalysts.71 The N1s core-level XPS spectrum of pristine NCMP2 shows one binding energy at 399.7 eV owing to C-N bond of the NPh3 moiety (Figure 5c). After PdCl2 loading, it becomes less intense and a new signal at a binding energy of 400.1 eV appears (Figure 5d). This signal can be attributed to the PdCl2-coordinated NPh3 moiety. SEM and TEM images indicate that the catalyst maintain the morphology of sphere-like nanoparticles after PdCl2 impregnation (Figure 2b,e,h and Figure 7a,c), with some dark dots that show the additionally formed Pd nanoparticles.

Intensity /a.u.

Pd (220) Pd (311)

Cl2s Cl2p

Pd (200)

N1s 3/2 Pd3d

Pd (111)

O1s

PdCl2

Intensity /a.u.

NCMP2 NCMP2-PdCl2

5/2

NCMP2 NCMP2-PdCl2

C1s

(b)

Pd3d

(a)

Intensity /a.u.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

0

20

40

60

80

1000

2Theta /degree

800

600

400

200

0

Binding energy /eV

Figure 4 (a) Powder XRD patterns and (b) XPS survey spectra of NCMP2 and NCMP2-PdCl2; PdCl2 is showed for comparison.

11

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

(a)

(c)

5/2

3/2

Pd3d

346

344

N1s

Intensity /a.u.

Intensity /a.u.

Pd3d

342

340

338

336

334

404

Binding energy /eV

(b)

Intensity /a.u.

3/2

Pd3d

344

342

340

338

400

398

396

(d)

5/2

346

402

Binding energy /eV

Pd3d

Intensity /a.u.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 12 of 23

336

334

Binding energy /eV

N1s N1s

404

402

400

398

396

Binding energy /eV

Figure 5 Pd3d (a,b) and N1s (c,d) core-level XPS spectra of (a) PdCl2, (c) NCMP2, and (b,d) NCMP2-PdCl2 catalyst.

Applying NCMP2-PdCl2 as a catalyst enables fast Suzuki–Miyaura coupling reactions in a 60% ethanol aqueous solution under mild conditions (80 oC). With a series of aryl bromides and benzeneboronic acid used, biaryl products were obtained consistently in high yields (Table 2). The presence of additional Pd(0) nanoparticles within our NMCP materials could play a role and influence the catalytic performance of these materials, and would be valid grounds for further detailed studies into the catalytic behaviour of these complex systems. The NCMP2-PdCl2 catalyst can be readily recycled by filtration and solvents washes. Applying phenyl bromide and benzeneboronic acid as substrates, the recyclability tests show that the yields of the cross-coupling products remain >94% after six repeat reactions with the recycled catalysts (Figure 6, see supporting information for details of the procedure followed). Control experiments using pristine PdCl2 as catalyst indicated no recyclability (although they showed catalytic activity close to that of the catalyst in presence of NCMP2 in the first cycle).

12

ACS Paragon Plus Environment

Page 13 of 23

Table 2 Suzuki–Miyaura coupling reaction catalyzed by NCMP2-PdCl2.

Entry

a

Substrate 1

Reaction time

Yield

1a