Optical Property Measurements of Mixed Coal Fly Ash and Particulate

Oct 16, 2017 - Thus, the advent of mercury emissions standards for power plants has the potential for increased emissions of PAC. Our previous analyse...
0 downloads 22 Views 2MB Size
Subscriber access provided by UNIV OF MISSOURI ST LOUIS

Article

Optical Property Measurements of Mixed Coal Fly Ash and Particulate Carbon Aerosols Likely Emitted During Activated Carbon Injection for Mercury Emissions Control Tian Xia, and Herek L. Clack Energy Fuels, Just Accepted Manuscript • DOI: 10.1021/acs.energyfuels.7b02046 • Publication Date (Web): 16 Oct 2017 Downloaded from http://pubs.acs.org on October 26, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Energy & Fuels is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 33

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

1

Optical Property Measurements of Mixed Coal Fly

2

Ash and Particulate Carbon Aerosols Likely Emitted

3

During Activated Carbon Injection for Mercury

4

Emissions Control

5

Tian Xia*, Herek L. Clack

6

Department of Civil and Environmental Engineering, University of Michigan, Ann Arbor,

7

Michigan, United States

8 9 10

KEYWORDS: Mercury; Electrostatic Precipitation; Powdered Activated Carbon; Black Carbon; Optical Absorption; Light Scattering.

11

12

ABSTRACT: The most mature technology for controlling mercury emissions from coal

13

combustion is the injection into the flue gas of powdered activated carbon (PAC) adsorbents

14

having chemically treated surfaces designed to rapidly oxidize and adsorb mercury. However,

15

carbonaceous particles are known to have low electrical resistivity, which contributes to their

16

poor capture in electrostatic precipitators (ESPs), the most widely used method of particulate

17

control for coal-fired power plants worldwide. Thus, the advent of mercury emissions standards

ACS Paragon Plus Environment

1

Energy & Fuels

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 2 of 33

18

for power plants has the potential for increased emissions of PAC. Our previous analyses have

19

provided estimates of PAC emission rates resulting from PAC injection in the U.S. and

20

extrapolated these estimates globally to project their associated climate forcing effect. The

21

present work continues our examination by conducting the first comparative measurements of

22

optical scattering and absorption of aerosols comprised of varying mixtures of coal combustion

23

fly ash and PAC. A partially fluidized bed (FB) containing fly ash-PAC admixtures with varying

24

PAC concentrations elutriates aerosol agglomerates. A photo-acoustic extinctiometer (PAX)

25

extractively samples from the FB flow, providing measurements of optical absorption and

26

scattering coefficients of fly ash (FA) alone and FA-PAC admixtures. Extracted aerosol samples

27

from the FB flow provide particulate loading measurements, thermogravimetric analysis (TGA)

28

provide estimations of the carbon content of the particulates collected from the FB emission, and

29

SEM images of the collected aerosols provide qualitative insight into the aerosols’ size

30

distributions and agglomeration state. Soot from an oil lamp flame provides a comparative

31

benchmark. The results indicate that the increase of carbonaceous particles in the FB emissions

32

can cause a significant linear increase of their mass absorption cross sections (MAC). Thus,

33

widespread adoption of activated carbon injection (ACI) in conjunction with ESPs has the

34

potential to constitute a new source of light absorbing particle emissions which can absorb light

35

efficiently and potentially act like BC in the atmosphere.

ACS Paragon Plus Environment

2

Page 3 of 33

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

36 37

Abstract Art. Measured linear increase of MAC and MSC, linear decrease of SSA of fly ash

38

emissions due to PAC addition.

39

ACS Paragon Plus Environment

3

Energy & Fuels

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 4 of 33

40

INTRODUCTION

41

Mercury (Hg) is an environmental pollutant of concern due to its tendency to cycle between soil,

42

air, and water; its bioaccumulation within the food chain; and its toxic effects on human and

43

wildlife health. Coal-fired power plants (CFPPs) are one of the major sources of anthropogenic

44

mercury emissions. According to United Nations Environment Programme (UNEP), coal

45

combustion accounts for 24% of anthropogenic mercury emissions, which is the second largest

46

source.1 In the U.S., about 50% of anthropogenic mercury emission is from electric generating

47

units (EGUs), mostly CFPPs.2 In China, coal combustion is responsible for 37% of mercury

48

emissions of which only 14% is from CFPPs and the remainder attributable to uncontrolled

49

industrial and household burning of coal.3 Anthropogenic mercury emission is regulated by

50

several countries in the world. In 2013, the Governing Council of the UNEP agreed on the

51

Minamata Convention on Mercury, which is a global treaty that requires countries to reduce

52

anthropogenic mercury emissions from all sources. In 2012, the U.S. EPA finalized its Mercury

53

and Air Toxics Standard (MATS), which requires existing CFPPs to reduce their mercury

54

emissions by 90% starting in 2015. Although the standard was rejected by the U.S. Supreme

55

Court in June, 2015 due to insufficient consideration of the costs of the regulation, most electric

56

utilities in the U.S. are continuing with their plans to comply with the regulation, including an

57

estimated 30 GW of small or old units being retired.4 In China, a revised national emission

58

standard for CFPPs, which took effect in 2012, limits mercury emissions from CFPPs to 0.03

59

mg/m3.5

60

Among the most mature technologies that have been developed for controlling mercury

61

emissions from CFPPs, the injection into the flue gas of powdered activated carbon (PAC)

62

adsorbents is attractive for its low capital costs, the small footprint of each installation, and

ACS Paragon Plus Environment

4

Page 5 of 33

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

63

smaller ancillary impacts on other pollutants or pollutant control processes as compared to other

64

Hg control technologies. Current PAC products for Hg removal have chemically treated surfaces

65

designed to rapidly oxidize and adsorb mercury during the seconds of contact time with the flue

66

gas after injection and before its removal with fly ash in a downstream particulate control device,

67

predominately electrostatic precipitators (ESPs). Detailed descriptions of PAC injection as well

68

as other mercury control technologies can be found in other reports.6,7 In 2011, the U.S. EPA

69

estimated that a total of 148 GW of coal combustion EGUs would install activated carbon

70

injection (ACI) technologies in order to comply with MATS,2 and according to U.S. Energy

71

Information Administration’s (EIA) annual report, 106 GW of ACI has been installed in CFPPs

72

by 2015.8 There is no particular mercury emissions control technology being installed for CFPPs

73

in China, but ACI is believed to be the most promising technology due to the prevalence of ESPs

74

in China.9 The drawback of ACI is that the efficiency of PAC removal in ESPs is lower than fly

75

ash since the electrical resistivity of PAC (< 104 ohm-cm10,11) is far below the range for optimal

76

ESP removal efficiency (108−1012 ohm-cm12,13). As a result, it would be expected that PAC

77

would be preferentially emitted from CFPPs during the application of ACI, at a rate that is as yet

78

unknown. In early 2000’s, US Dept. of Energy funded a series of pilot-scale testing on ACI

79

injection and the darkened particulate filters collected at the ESP outlet at Stanton Unit 1 (a 150-

80

MW Foster Wheeler wall-fired boiler that has been operational since 1966 and is equipped with

81

three coal feeders and pulverizers and two cold-side ESPs in parallel (SCA = 470 ft2/1000 afcm))

82

confirmed the increase of PAC emission.14 Further, sub-micron, black-colored PAC aerosols

83

(~4% in volume)15 would be expected to have optical properties similar to submicron black

84

carbon (BC, i.e. soot, average size of 0.15-0.40 µm16,17,18) that can form during fossil fuel

85

combustion. CFPPs without ACI installed were considered to have little contribution to BC

ACS Paragon Plus Environment

5

Energy & Fuels

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 6 of 33

86

emission. Bond et al.19 estimated that only 0.6% of PM emitted from pulverized coal combustors

87

were black carbon, and Cao et al.20 reported that power generation only contributed to 0.5% of

88

BC emission in China. Clack21 developed estimates indicating that the contributions of CFPPs to

89

total U.S. anthropogenic BC emissions (i.e., excluding wildfires) could increase from less than

90

6% to 8% in 2020, and from less than 8% to 11% by 2030, due to the emitted PAC. While the

91

percent of CFPPs adopting ACI was a primary factor in the variability of the estimates, the

92

unknown degree to which ESPs collect PAC less efficiently than fly ash was the principle

93

uncertainty.

94

The climate warming effect of PAC and atmospheric BC is far less well understood than that of

95

CO2. Bond et al. suggested a 7.5 ± 1.2 m2/g mass absorption cross section (MAC) for black

96

carbon at 550 nm, and a 0.2-0.3 single scattering albedo.22 The 2013 Intergovernmental Panel on

97

Climate Change (IPCC) report estimates the direct forcing effect of BC to be 0.05-0.8 Wm-2, and

98

illustrates that BC can have the second largest effect on climate forcing behind CO2.23 It is

99

believed that the addition of PAC emissions from CFPPs due to ACI would further increase the

100

overall BC radiative forcing unintentionally. According to the model developed by Lin et al,24

101

the submicron PAC emissions, if applied globally to CFPP particulate emissions, could cause a

102

global warming of 2.10 mW m−2 at the top of atmosphere and a cooling of −2.96 mW m−2 at the

103

surface. In addition, comparing the warming effects of emitted CO2 and PAC, each normalized

104

by its respective rate of carbon input (as fuel for CO2; as carbon in PAC for ACI), it was

105

determined that emitted submicron PAC has eight times larger climate forcing per unit carbon

106

input than CO2. These results, however, assume that the emitted PAC has the same optical

107

properties as that of BC, while the actual optical properties of PAC are unknown. Furthermore,

108

most simulations of BC climate forcing, including that of Lin et al., assume that emitted coal

ACS Paragon Plus Environment

6

Page 7 of 33

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

109

combustion fly ash (FA) is entirely mineral and entirely scattering, while in fact, fly ash varies

110

widely in color and carbon content, and PAC injection can enhance those variations. In order to

111

better understand the actual climate forcing potential of incidentally emitted PAC, it is necessary

112

to better understand PAC emission rates (complement of collection rates in particulate control

113

devices) and the optical properties of PAC, FA and PAC-FA agglomerates.

114

In this paper, we aim to provide the first comparative measurements of optical scattering and

115

absorption of aerosols comprised of varying mixtures of coal combustion fly ash and PAC, in an

116

effort to better constrain the potential climate forcing effects of emitted PAC resulting from ACI

117

used to reduce mercury emissions. Soot is also collected and analyzed to provide a black carbon

118

standard against whose optical properties the fly ash and PAC mixtures could be compared. A

119

photoacoustic extinctiometer (PAX, Droplet Measurement Technologies, Boulder, CO) is used

120

to optically characterize both the combustion soot and the effluent from a partially fluidized bed

121

(FB) of prepared mixtures of PAC and FA samples obtained from the hoppers of power plant

122

ESPs. Extracted aerosol samples from the FB effluent provide the particulate mass loading

123

measurements. Thermogravimetric analysis (TGA) is applied to evaluate the carbon content of

124

the mixed aerosols in the FB effluent.

125

MATERIALS AND METHODS

126

Experimental Setup

127

For this experiment, fly ash samples were collected from the first three rows of hoppers of a

128

utility ESP at DTE’s Belle River (BR) Power Plant in Michigan. At the time of fly ash

129

collection, the Belle River station burned a low-sulfur, western sub-bituminous coal. Because of

130

the cohesive properties of the finer ash taken from the second and third rows, only fly ashes from

ACS Paragon Plus Environment

7

Energy & Fuels

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 8 of 33

131

the first row of hoppers were used here, with the result being that these ash samples are a coarser

132

fraction of the overall size distribution of ash collected in the ESP. Unburned carbon content was

133

determined from loss on ignition (LOI) measurements conducted by DTE Central Chemical Lab.

134

Norit Darco FGD used in previous studies of fly ash-activated carbon behavior11,15,25 was the

135

powdered activated carbon (PAC) product added to the fly ash to form the particulate admixture,

136

mixed on a mass per mass basis. The PAC particles had a lognormal size distribution, with a

137

Sauter mean diameter of 5.9 µm and a long tail in the low end.15 It should be noted that PAC

138

samples used in this research had relatively large size distributions as compared to freshly

139

emitted BC, which may affect the particles’ optical properties. Bond et al.22 and Martins et al.26

140

have shown that the volume and/or mass absorption cross sections would decrease with

141

increasing particle size for particles are larger than 0.1 µm. Particle’s scattering property is

142

governed by the ratio of the particle size to the light wavelength, and generally for particles

143

larger than 1 µm, the scattering coefficient would decrease with increasing particle size.27

144

Admixtures consisted of BR FA samples amended with 0%, 0.5%, 1% and 2% (by mass) PAC.

145

The two constituents were added to PTFE bags and the bags were tumbled inside the barrel of a

146

rock tumbler (Thumler's Tumbler, Model B), for 10 minutes to ensure thorough mixing and

147

uniform distribution of the PAC in the fly ash.

148

During measurement of optical properties, the FA-PAC aerosols were elutriated from the

149

partially fluidized bed. Before fluidization, an empty fluidization vessel was loaded with 1,000

150

grams of each prepared admixture. Facility-supplied dried (10% RH) compressed air entered the

151

vessel from below at five liters per minute (LPM) to partially fluidize the loaded admixture, a

152

fraction of which was continuously elutriated, from which real-time optical characterization and

153

aerosol integrated average mass loading determinations were made. Two sampling probes were

ACS Paragon Plus Environment

8

Page 9 of 33

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

154

installed in the top of the fluidized bed: one was connected to the PAX which sampled a portion

155

of the elutriate (1 LPM) and took readings of scattering coefficients and absorption coefficients

156

simultaneously; the other probe was connected to a particulate filter (filter cases: Savillex, Model

157

No. 401-21-47-10-21-2; Polycarbonate filter: Whatman, 131135012E) used to determine the

158

average aerosol mass loading of the elutriate which was weighed before and after collecting

159

samples using an analytical balance. A rotameter (Omega, Model No. FL3840-ST) connected

160

downstream of the PM filter indicated the air flow rate through the filter. The air flow rate

161

needed to establish partial fluidization of the admixture varies with particle size (i.e., changing

162

fluidization regime, based on Geldart classification28), and in all cases exceeds the PAX

163

sampling flow rate. As a result, most of the elutriated flow from the fluidized bed was directed to

164

an auxiliary PM filter and only 1LPM flow was directed into PAX. This auxiliary filter was not

165

used for mass loading measurements but rather to maintain the same exhaust flow rate, and thus

166

the same fluidization air flow rate and fluidized bed behavior, inside the vessel.

167

For the optical characterization of combustion-generated soot, an oil lamp (TIKI® Molded Glass

168

Table Torch, Model No. 114109, burning TIKI® Brand Citronella Torch Fuel) was positioned at

169

the bottom of a brick chimney built with four equally spaced openings around its periphery to

170

promote a swirling updraft to stabilize the flame. A sampling probe connected to a vacuum pump

171

sampled from the plume of the sooting flame at the top of the chimney at a rate of 12 LPM, a

172

flow which was divided into two streams: one (1 LPM) directed to the PAX and the other (11

173

LPM) directed to the PM filter for aerosol mass loading determination.

174

Measurement Processes

ACS Paragon Plus Environment

9

Energy & Fuels

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 10 of 33

175

In this experiment, the duration of the PAX measurement cycle was set to 500 seconds. In each

176

measurement cycle, the first 70 seconds were devoted to automated flushing the PAX

177

measurement chamber with clean air and zero all sensors. The remaining 430 seconds were

178

devoted to taking optical property measurements (referred to as the measurement stage).

179

For each new FA-PAC admixture, the fluidized bed was allowed to freely and continuously

180

elutriate for at least 90 minutes before any measurements were taken to reduce aerosol mass

181

loading so that the measured absorption and scattering coefficients were within the measurement

182

range of PAX (30% carbon content should be due to carbon content fluctuations in the emission

359

from the FB, where active fluidization was promoted by the addition of PAC.

360 361

Figure 6. Correlation of the obtained MSC and MAC with particles’ carbon content.

362

In addition to the MAC and MSC, the SSAs of the emissions for every two seconds’ PAX data

363

points were calculated, and the final SSA of the emissions from each FB with a specific bed FA-

364

PAC mixing ratio were calculated by averaging the three groups of data points. The correlation

365

of the calculated SSAs with the emissions’ carbon contents is presented in Figure 7 with a data

366

point representing the soot measurement result assuming a 100% carbon content. From the

367

figure, it can be found that the SSA of the FA-PAC admixture particles decreases linearly with

368

the increase of carbon content with a slope of -0.82. When the carbon content reaches 100%, the

369

SSA obtained from the trend line is 0.13, which is about half of the measured soot SSA. This

370

may be because of the assertive assumption that soot contains 100% carbon. Soot is a mixture of

371

carbon and various organic materials, and to further examine the optical propriety of soot

372

generated in this research, its chemical composition should be studied.

ACS Paragon Plus Environment

20

Page 21 of 33

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

373 374

Figure 7. Correlation of the obtained SSA with particles’ carbon content.

375

Comparison with Other Research

376

In this section, the optical properties obtained in last section are compared with relevant

377

measurement results from other research. The comparison is only focused on MAC and SSA

378

results since the two properties are the most commonly used ones by models to predict aerosol

379

climate forcing.

380

The MAC of soot, or black carbon (BC), has been measured and reported by many researchers,

381

while the results vary significantly due to the vague definition of black carbon. Before any

382

comparison, it should be noted that the aerosol light absorption property is dependent on the

383

wavelength of light. The equation below is a commonly used one to characterize the spectral

384

dependence of MAC using the absorption Ångstrom exponent (Åabs):

385

MAC=Kλ- Åabs

386

where K is a constant and λ is the wavelength of light.31 Bond29 suggested Åabs=1 in regions

387

where externally mixed BC dominates absorption, while it is stressed that the assumption is only

388

valid over the light wavelength throughout the visible spectrum.22 The research conducted by

ACS Paragon Plus Environment

21

Energy & Fuels

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 22 of 33

389

Kirchstetter32 measuring light attenuation by soot generated from motor vehicles throughout the

390

light wavelength from 330nm to 1000nm proved that the assumption of Åabs=1 is valid over a

391

larger wavelength range, which is supported by the research of Russell et al.33 In this research the

392

wavelength used by PAX is 870nm and it is assumed that Åabs=1 for all samples, which means

393

that the obtained MACs depend inversely on light wavelength.

394

Bond and Bergstrom22 suggested a value of 7.5±1.2 m2/g (550nm wavelength) for the MAC of

395

fresh light-absorbing carbon, which is over two times that of the acquired soot MAC (3.4 m2/g

396

adjusted to 550nm) in this research. Other photoacoustic measurements of BC aerosols emitted

397

from diesel engines or acetylene smoke also suggested much larger MAC values.34,35,36 One

398

reason of the low MAC value obtained in this research may be the low temperature and short

399

height of the oil lamp flame. Combustion generated carbon is a type of amorphous carbon which

400

contains both sp3 and sp2 bonds, and the islands of sp2-bonded (graphitic) clusters control the

401

light-absorbing properties of the particle.37 The transformation of carbon with primarily sp3

402

bonds to that with sp2 bonds is called graphitization, which is a common process that occurs to

403

carbonaceous particles passing through the flame and is positively correlated to the flame

404

temperature and particles’ residence time in flame. The flame generated by an oil lamp in this

405

research was only about 10 cm tall, which is expected to have a relatively low flame temperature

406

compared with diesel engines and acetylene flames, and emit carbonaceous particles quickly into

407

the surrounding environment.38,39 As a result, fewer sp2 bonds were formed in the sampled soot

408

and therefore the measured MAC was low.

409

The soot SSA obtained in this research is 0.29, which is within the 0.2-0.3 value range suggested

410

by Bond and Bergstrom22. The value of SSA depends one both light wavelength and particle size

411

distributions, so further comparison of the obtained SSA with other measurement results is not

ACS Paragon Plus Environment

22

Page 23 of 33

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

412

representative and applicable. The measurements also report a SSA value of 0.98 for BR fly ash,

413

which is comparable with the sand duct SSA value reported previously by other researchers.

414

Tanre et al.40 reported a 0.96-0.97 value for the SSA of sand dust measured using 870nm

415

wavelength light, and Kim et al.41 reported a SSA of 0.94-0.95 over a wide wavelength range.

416

These consistent results are reasonable since the major chemical component of FA and sand dust

417

are both SiO2. Because of this similarity, the emission of FA from CFPPs is often assumed to be

418

entirely mineral in climate simulations of BC climate forcing and BC emissions

419

inventories.19,20,42

420

Estimation of PAC emissions from CFPPs

421

According to the discussion in the last section, the emission of FA from CFPPs is often assumed

422

to be entirely mineral, while the measurement results presented in Figure 6 show that the

423

increase of carbon content of the particles emitted from the power plants may cause a significant

424

linear increase of MAC of the emissions. It is expected that the installation of ACI technologies

425

has the potential to increase the carbon content of CFPPs’ emissions, and in this section the

426

carbon content (as the PAC mass fraction of the total particles emitted) of the emission from an

427

ESP is examined as a function of the ESP’s FA removal efficiency.

428

Figure 8 shows the calculation results of the emission carbon content ([PAC]out) as a function of

429

ESP’s FA collection efficiency (ηFA). In the calculation it is assumed that 0.5% PAC by mass

430

was mixed with the FA in the flue gas upstream of the ESP, and the ESP’s PAC collection

431

efficiency (ηPAC) either had a constant differential with ηFA (ηFA-ηPAC=const.), or was a constant

432

fraction of ηFA (ηPAC/ηFA=const.). From the figure it can be found that for both ηPAC assumptions,

433

as ηFA approaches 100%, there will be significant carbon content increases (up to 60%) in the

ACS Paragon Plus Environment

23

Energy & Fuels

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 24 of 33

434

emission. Modern ESPs generally have ηFA larger than 95% or even larger than 99%,43 so it is

435

reasonable to claim that the installation of ACI technologies will significantly increase the

436

carbon content in the CFPPs’ emissions. If PAC and FA particles do not agglomerate as

437

discussed in Section “Physical characterization of FB emissions”, the increased carbon content

438

will be emitted as individual carbonaceous particles, which makes CFPPs a new source of BC

439

emissions. This new BC source is a large-scale point source, generally operated under steady

440

state conditions yielding relatively steady BC emissions, which is quite different from most of

441

the conventional BC sources that are believed to be either small and numerous, or large but

442

episodic.29 Due to CFPPs’ nature of relatively steady emission, BC emission should be

443

monitored by CFPPs with ACI installed and the international BC emission inventories for CFPPs

444

should be established for the emission control and simulation of climate forcing associated with

445

BC emissions from CFPPs, in a way that cannot be done with other BC sources.

446 447

(a)

(b)

448

Figure 8. Calculated ESP emission carbon contents as function of ηFA assuming (a) ηFA-

449

ηPAC=const. or (b) ηPAC/ηFA=const. (Colored)

450 451

ACS Paragon Plus Environment

24

Page 25 of 33

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

452

CONCLUSIONS AND LIMITATIONS

453

This research measured Babs, Bscat and mass loadings of combustion-generated soot as well as

454

FA/FA-PAC aerosols emitted from a fluidized bed, and calculated the corresponding MSC,

455

MAC and SSA of soot, FA aerosols and FA-PAC admixture aerosols. For the relatively large

456

PAC and FA particles sampled in the experiment, the SEM images indicate agglomeration in the

457

flue gas is unlikely. Both MSC and MAC of FA-PAC admixture aerosols would increase linearly

458

with the increase of particles’ carbon content, while the increase of carbonaceous particles in the

459

FB emissions had a more significant effects on the MAC of the particles in the emissions, and

460

the SSA would decrease linearly with the carbon content increase. The acquired MAC value of

461

soot is relatively low compared with other reported values, which may be due to the small size of

462

the oil lamp flame, and the acquired SSA values for both soot and FA are comparable with other

463

relevant reports. The measurements and calculations illustrated that the installation of ACI in

464

CFPPs would increase the MAC of the emissions from the power plants and make the CFPPs a

465

new source of light absorbing particle emissions. Although large in average size, the emitted

466

PAC particles, especially the submicron fraction, can absorb light efficiently and potentially act

467

like BC in the atmosphere. Further studies should be conducted to quantify the intensity of this

468

new emission and examine its potential climate forcing effects.

469

Several limitations have been observed during the research. The measurements conducted for FB

470

emissions only sampled relatively large particles since the smaller particles may have been

471

exhausted during the free elutriation of the FB before any measurements, and the size

472

distributions of the sampled particles were not fully examined. In future a dilution chamber

473

should be built downstream of the FB to capture and dilute the small particles emitted by the FB

474

during the early stage of fluidization for PAX measurements, and scanning mobility particle sizer

ACS Paragon Plus Environment

25

Energy & Fuels

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 26 of 33

475

spectrometer (SMPS) should be utilized to further examine the size distribution of sampled

476

particles. Last but not least, since most CFPPs use industrial opacity sensors to monitor their PM

477

emissions, the light extinction measured by PAX and industrial opacity sensors should be

478

compared to examine the effectiveness of opacity sensors on detecting carbon emissions from

479

CFPPs.

480 481

ASSOCIATED CONTENT

482

Supporting Information. One two-page file containing one figure showing the FA-PAC

483

admixtures with different PAC mixing ratio.

484

.

485

AUTHOR INFORMATION

486

Corresponding Author

487

*1913 McIntyre Street, Ann Arbor, MI, USA 48105-2420

488

*Phone: (+1)7346807921. E-mail: [email protected]; [email protected].

489

Author Contributions

490

The manuscript was written through contributions of all authors. All authors have given approval

491

to the final version of the manuscript.

492

Funding Sources

493

No funding was received for this research project.

494

Notes

495

The authors declare no competing financial interest.

ACS Paragon Plus Environment

26

Page 27 of 33

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

496

ACKNOWLEDGMENT

497

The authors thank Prof. James Hower, Dr. Kevin Henke (Univ. of Kentucky) and Tony Bassi

498

(DTE Energy) and the engineers at E.W. Brown and Trimble County electric generating stations

499

of Louisville Gas & Electric and Kentucky Utilities Co. for providing plant access and assisting

500

with fly ash collection. The authors also thank Cristina Koss, Alexander Mattia and Akosua

501

Miller for helping obtain the measurements, to Prof. Andre Boehman and Chenxi Sun (Univ. of

502

Michigan) for conducting the TGA measurements, and to Gavin McMeeking and John Walker at

503

DMT for their technical support in operating the PAX. No funding was received for this research

504

project.

505

ABBREVIATIONS

506

ACI, activated carbon injection; BC, black carbon; CFPPs, Coal-fired power plants; EIA, Energy

507

Information Administration; EGUs, electric generating units; EPA, Environmental Protection

508

Agency; ESP, electrostatic precipitator; FA, fly ash; FB, fluidized bed; IPCC, Intergovernmental

509

Panel on Climate Change; LOI, loss on ignition; LPM, liter per minute; MAC, mass absorption

510

cross sections; MATS, Mercury and Air Toxics Standard; MSC, scattering cross section; PAC,

511

powdered activated carbon; PAX, photo-acoustic extinctiometer; SEM, scanning electron

512

microscopy; SMPS, scanning mobility particle sizer spectrometer; SSA, single scattering albedo;

513

TGA, thermogravimetric analysis; UNEP, United Nations Environment Programme.

514

ACS Paragon Plus Environment

27

Energy & Fuels

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

515

REFERENCES

516

(1) Global Mercury Assessment 2013: Sources, Emissions, Releases and Environmental

517

Transport; UNEP Chemicals Branch: Geneva, Switzerland, 2013.

518

http://www.unep.org/PDF/PressReleases/GlobalMercuryAssessment2013.pdf.

519

(2) Regulatory Impact Analysis for the Final Mercury and Air Toxics Standards; US

520

Environmental Protection Agency: Research Triangle Park, NC, December 2011.

521

https://www3.epa.gov/ttnecas1/regdata/RIAs/matsriafinal.pdf.

522

Page 28 of 33

(3) Wu, Y.; Wang, S.; Streets, D. G.; Hao, J.; Chan, M. & Jiang, J. Trends in anthropogenic

523

mercury emissions in China from 1995 to 2003. Environmental science & technology 2006,

524

40 (17), 5312-5318.

525 526 527

(4) EIA, 2014: Coal-fired power plant operators consider emissions compliance strategies; http://www.eia.gov/todayinenergy/detail.cfm?id=15611 (5) Ministry of Environmental Protection of the People’s Republic of China, Emission Standard

528

of Air Pollutants for Thermal Power Plants, GB 13223.2011.

529

http://switchboard.nrdc.org/blogs/bfinamore/NRDC%20Unofficial%20English%20Summary

530

.docx

531

(6) Srivastava, R. K., Hutson, N., Martin, B., Princiotta, F., & Staudt, J. Control of mercury

532

emissions from coal-fired electric utility boilers. Environmental science & technology 2006,

533

40, 1385-1393.

534 535

(7) Granite, E. J., Pennline, H. W., & Senior, C. Eds. Mercury Control: for Coal-Derived Gas Streams. John Wiley & Sons, 2014.

ACS Paragon Plus Environment

28

Page 29 of 33

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

536 537 538 539 540 541

Energy & Fuels

(8) Electric Power Annual 2015; U.S. Energy Information Administration: Washington, DC, November 2016. https://www.eia.gov/electricity/annual/pdf/epa.pdf. (9) Zhou, J.; Luo, Z.; Zhu, Y.; Fang, M. Mercury Emission and Its Control in Chinese Coal-fired Power Plants; Springer Berlin Heidelberg, 2013. (10) Espinola, A.; Miguel, P.M.; Salles, M.R.; Pinto, A.R. Electrical properties of carbonsresistance of powder materials. Carbon 1986, 24 (3), pp. 337–341.

542

(11) Lee, E.M. and Clack, H.L. Powder Resistivity Inferred Differential Collection of

543

Heterogeneous Coal Fly Ash and Powered Activated Carbon Admixtures within a

544

Cylindrical Electrostatic Precipitator. Emission Control Science and Technology 2016, 2 (1),

545

33-43.

546 547 548 549

(12) Calvert, S.; Englund, H. M. Handbook of Air Pollution Technology; Wiley-Interscience: Hoboken, NJ, 1984. (13) Davis, W. T., Eds. Air Pollution Engineering Manual; Wiley-Interscience: Hoboken, NJ, 2000.

550

(14) Dombrowski, K.; Richardson, C.; Padilla, J.; Chang, R.; Archer, G.; Fisher, K.; Smokey, S.;

551

Brickett, L. Evaluation of Novel Mercury Sorbents and Balance-of-Plant Impacts at Stanton

552

Unit 1; DOE-U.S. EPA-EPRI-AWMA Power Plant Air Pollution Control ″ Mega ″

553

Sympsoium, Baltimore, MD, 2008.

554

(15) Prabhu, V.; Kim, T.; Khakpour, Y.; Serre, S.; Clack, H. L. Evidence of Powdered Activated

555

Carbon Preferential Collection and Enrichment on Electrostatic Precipitator Discharge

ACS Paragon Plus Environment

29

Energy & Fuels

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 30 of 33

556

Electrodes during Sorbent Injection for Mercury Emissions Control. Fuel Processing

557

Technology, 2012, 93, 8-12.

558 559

(16) Clague, A. D. H., Donnet, J. B., Wang, T. K., & Peng, J. C. M. A comparison of diesel engine soot with carbon black. Carbon, 1999, 37(10), 1553-1565.

560

(17) Schneider, J., Kirchner, U., Borrmann, S., Vogt, R., & Scheer, V. In situ measurements of

561

particle number concentration, chemically resolved size distributions and black carbon

562

content of traffic-related emissions on German motorways, rural roads and in city traffic.

563

Atmospheric Environment, 2008, 42(18), 4257-4268.

564

(18) Hitzenberger, R., & Tohno, S. Comparison of black carbon (BC) aerosols in two urban

565

areas–concentrations and size distributions. Atmospheric Environment, 2001, 35(12), 2153-

566

2167.

567

(19) Bond, T. C., Streets, D. G., Yarber, K. F., Nelson, S. M., Woo, J. H., & Klimont, Z. A

568

technology ‐ based global inventory of black and organic carbon emissions from

569

combustion. Journal of Geophysical Research: Atmospheres, 2004, 109(D14).

570 571

(20) Cao, G., Zhang, X., & Zheng, F. Inventory of black carbon and organic carbon emissions from China. Atmospheric Environment, 2006, 40(34), 6516-6527.

572

(21) Clack, H. L. Estimates of Increased Black Carbon Emissions from Electrostatic

573

Precipitators during Powdered Activated Carbon Injection for Mercury Emissions Control.

574

Environ. Sci. Technol. 2012, 46 (13), pp 7327–7333.

ACS Paragon Plus Environment

30

Page 31 of 33

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

575 576

Energy & Fuels

(22) Bond, T. C. and Bergstrom, R. W. Light absorption by carbonaceous particles: An investigative review. Aerosol science and technology 2006, 40 (1), 27-67.

577

(23) IPCC: Climate Change 2013: The Physical Science Basis. Contribution of Working Group I

578

to the Fifth Assessment Report of the Intergovernmental Panel on Climate Change; Stocker,

579

T. F., Qin, D., Plattner, G.-K., Tignor, M., Allen, S. K., Boschung, J., Nauels, A., Xia, Y.,

580

Bex, V., Midgley, P. M., Eds.; Cambridge University Press: Cambridge, United Kingdom,

581

2013; p 1535.

582

(24) Lin, G.; Penner, J. E.; Clack, H. L. Radiative Forcing Associated with Particulate Carbon

583

Emissions Resulting from the Use of Mercury Control Technology. Environ. Sci. Technol.

584

2014, 48 (17), pp 10519–10523.

585

(25) Prabhu, V.; Lee, S.; Clack, H. L. Electrostatic Precipitation of Powdered Activated Carbon

586

and Implications for Secondary Mercury Adsorption within ESPs. Energy & Fuels 2011, 25

587

(3), pp 1010-1016

588

(26) Martins, J. V., Artaxo, P., Liousse, C., Reid, J. S., Hobbs, P. V., & Kaufman, Y. J. Effects

589

of black carbon content, particle size, and mixing on light absorption by aerosols from

590

biomass burning in Brazil. Journal of Geophysical Research: Atmospheres, 1998, 103(D24),

591

32041-32050.

592 593 594

(27) Hinds, W. C. Aerosol technology: properties, behavior, and measurement of airborne particles. John Wiley & Sons, 2012. (28) Geldart, D. Types of gas fluidization. Powder Technology, 1973, 7 (5), 285-292.

ACS Paragon Plus Environment

31

Energy & Fuels

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 32 of 33

595

(29) Bond, T. C.; Doherty, S. J.; Fahey, D. W.; Forster, P. M.; Berntsen, T.; DeAngelo, B. J.; ...

596

& Kinne, S. Bounding the role of black carbon in the climate system: A scientific

597

assessment. Journal of Geophysical Research: Atmospheres 2013, 118 (11), 5380-5552.

598

(30) Gladney, E. S.; Small, J. A.; Gordon, G. E.; Zoller, W. H. Composition and size distribution

599

of in-stack particulate material at a coal-fired power plant. Atmospheric Environment (1967)

600

1976, 10 (12), 1071-1077.

601

(31) Bond, T. C. Spectral dependence of visible light absorption by carbonaceous particles

602

emitted from coal combustion. Geophysical Research Letters 2001, 28 (21), 4075-4078.

603

(32) Kirchstetter, T. W.; Novakov, T.; and Hobbs, P. V. Evidence that the spectral dependence of

604

light absorption by aerosols is affected by organic carbon. Journal of Geophysical Research:

605

Atmospheres 2004, 109 (D21).

606

(33) Russell, P. B.; Bergstrom, R. W.; Shinozuka, Y.; Clarke, A. D.; DeCarlo, P. F.; Jimenez, J.

607

L.; ... and Strawa, A. Absorption Angstrom Exponent in AERONET and related data as an

608

indicator of aerosol composition. Atmospheric Chemistry and Physics 2010, 10 (3), 1155-

609

1169.

610

(34) Bruce, C. W.; Stromberg, T. F.; Gurton, K. P.; and Mozer, J. B. Trans-spectral absorption

611

and scattering of electromagnetic radiation by diesel soot. Applied optics 1991, 30 (12),

612

1537-1546.

613

(35) Szkarlat, A. C.; and Japar, S. M. Light absorption by airborne aerosols: comparison of

614

integrating plate and spectrophone techniques. Applied optics 1981, 20 (7), 1151-1155.

ACS Paragon Plus Environment

32

Page 33 of 33

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

615 616 617 618

Energy & Fuels

(36) Roessler, D. M.; and Faxvog, F. R. Optoacoustic measurement of optical absorption in acetylene smoke. JOSA 1979, 69 (12), 1699-1704. (37) Robertson, J.; and O’reilly, E. P. Electronic and atomic structure of amorphous carbon. Physical Review B 1987, 35 (6), 2946.

619

(38) Sattel, S., Robertson, J., & Ehrhardt, H. Effects of deposition temperature on the properties

620

of hydrogenated tetrahedral amorphous carbon. Journal of applied physics, 1997, 82(9),

621

4566-4576.

622

(39) Oberlin, A. Carbonization and graphitization. Carbon, 1984, 22(6), 521-541.

623

(40) Tanré, D.; Kaufman, Y. J.; Holben, B. E. A.; Chatenet, B.; Karnieli, A.; Lavenu, F.; ... and

624

Smirnov, A. Climatology of dust aerosol size distribution and optical properties derived from

625

remotely sensed data in the solar spectrum. Journal of Geophysical Research: Atmospheres

626

2001, 106 (D16), 18205-18217.

627

(41) Kim, D.; Chin, M.; Yu, H.; Eck, T. F.; Sinyuk, A.; Smirnov, A.; and Holben, B. N. Dust

628

optical properties over North Africa and Arabian Peninsula derived from the AERONET

629

dataset. Atmospheric Chemistry and Physics 2011, 11 (20), 10733-10741.

630

(42) Reddy, M. S., & Venkataraman, C. Atmospheric optical and radiative effects of

631

anthropogenic aerosol constituents from India. Atmospheric Environment, 2000, 34(26),

632

4511-4523.

633 634

(43) Cooper, C. D. and Alley, F. C. Air pollution control: A design approach. Waveland Press: Long Grove, IL, 2011.

ACS Paragon Plus Environment

33