Ordered Mesoporous Carbon as an Efficient and Reversible

It was then stirred vigorously until a milky solution was observed, followed by ..... Ajie, H.; Alvarez, M. M.; Anz, S. J.; Beck, R. D.; Diederich, F...
0 downloads 0 Views 217KB Size
Langmuir 2006, 22, 4583-4588

4583

Ordered Mesoporous Carbon as an Efficient and Reversible Adsorbent for the Adsorption of Fullerenes Huan Wang, Frank L. Y. Lam, Xijun Hu,* and Ka Ming Ng Department of Chemical Engineering, Hong Kong UniVersity of Science and Technology, Clear Water Bay, Hong Kong ReceiVed September 26, 2005. In Final Form: March 14, 2006 An ordered mesoporous carbon, CMK-3, was synthesized using a mesoporous siliceous material, SBA-15, as the template. CMK-3 was characterized and used for the adsorption of fullerenes C60 and C70. It was found that the adsorption capacity of CMK-3 is 4 times higher than that of activated carbon. The adsorption equilibrium isotherms of C60 and C70 on CMK-3 were studied for both single and binary systems. The reversibility of fullerene adsorption on CMK-3 was also explored. The results showed that CMK-3 is an effective and reversible adsorbent for the separation of fullerenes by adsorption.

Introduction The discovery of fullerene series C60 and C70 was first reported by Kroto, Curl, and Samlley in 1985.1 Fullerenes were described as the third form of ordered carbon having a structure very different from diamond and graphite. Over the past decade, many scientists have explored the physical and chemical properties of these novel molecules.2 Although fullerenes are considered to have many potential applications, such as in superconductors, industrial catalysts, and perhaps antiviral agents,3 their practical applications remain limited4 because of the difficult separation process used to produce pure fullerenes on a large scale. The techniques used for the separation and purification of C60 and C70 include selective complexation,5-9 fractional crystallization,10-13 and liquid chromatography.14-18 Fractional crystallization is useful for separating C60 and C70, but it cannot produce pure C70 and it requires stirring for a long time at elevated temperature and * Corresponding author. E-mail: [email protected]. Fax: (852) 2358 0054. Tel: (852) 2358 7134. (1) Kroto, H. W.; Heath, J. R.; OBrien, S. C.; Curl, R. F.; Smalley, R. E. Nature 1985, 318, 162-163. (2) Crowley, C.; Taylor, R.; Kroto, H. W.; Walton, R. M.; Cheng, P. C.; Scott, T. Synth. Met. 1996, 77, 17-22. (3) Baum, R. Chem. Eng. News. 1993, 71, 3-5. (4) Zajac, J.; Groszek, A. J. Carbon 1997, 35, 1053-1060. (5) Komatsu, N. Org. Biomol. Chem. 2003, 1, 204-209. (6) Komatsu, N. Tetrahedron Lett. 2001, 42, 1733-1736. (7) Atwood, J. L.; Koutsantonis, G. A.; Raston, C. L. Nature 1994, 368, 229231. (8) Ryuichi, S.; Kazuyoshi, T.; Yukiko, K.; Shigeo, I. Chem. Lett. 1994, 4, 699-704. (9) Bucsi, I.; Aniszfeld, R.; Shamma, T.; Prakash, G. K. S.; Olah, G. A. Proc. Natl. Acad. Sci. U.S.A. 1994, 91, 9019-9021. (10) Doome, R. J.; Fonseca, A.; Richter, H.; Nagy, J. B.; Thiry, P. A.; Lucas, A. A. J. Phys. Chem. Solids 1997, 58, 1839-1843. (11) Zhou, X.; Gu, Z.; Wu, Y.; Sun, Y.; Jin, Z.; Xiong, Y. Carbon 1994, 32, 935-937. (12) Wu, Y.; Sun, Y.; Gu, Z.; Zhou, X.; Xiong, Y.; Sun, B. Carbon 1994, 32, 1180-1182. (13) Coustel, N.; Bernier, P.; Aznar, R.; Zahab, A.; Lambert, J. M. J. Chem. Soc., Chem. Commun. 1992, 19, 1402-1403. (14) Ajie, H.; Alvarez, M. M.; Anz, S. J.; Beck, R. D.; Diederich, F.; Fostiropoulos, K.; Huffman, D. R.; Kratschmer, W.; Rubin, Y.; Schriver, K. E.; Sensharma, D.; Whetten, R. L. J. Phys. Chem. 1990, 94, 8630-8633. (15) Taylor, R.; Hare, J. P.; Abdul-Sada, A. K.; Kroto, H. W. J. Chem. Soc., Chem. Commun. 1992, 19, 1423-1425. (16) Vassalo, A. M.; Palmisano, A. J.; Pang, L. S. K.; Wilson, M. A. J. Chem. Soc., Chem. Commun. 1992, 1, 60-61. (17) Scrivens, W. A.; Bedworth, P. V.; Tour, J. M. J. Am. Chem. Soc. 1992, 114, 7917-7919. (18) Manolova, N.; Rashkov, I.; Legras, D.; Delpeux, S.; Beguin, F. Carbon 1995, 33, 209-213.

repeating the precipitation-filtration sequence a few times.19 Liquid chromatography seems to be the most convenient method for the laboratory-scale separation of C60 and C70. However, the unavailability of an effective and reversible adsorbent for fullerene adsorption seriously limits the application of liquid chromatography. Many researchers have carried out studies on the adsorption of fullerenes on various adsorbents. Taylor15 began with neutral alumina as the stationary phase to separate C60 and C70 but found that large amounts of expensive alumina and intensive labor are needed. Then, activated carbon (AC), for its very large specific surface area and high adsorption capacity, became the most popular adsorbent for fullerene separation. The high capacity of activated carbon to adsorb C60 and C70 allows the quantity of the stationary phase to be reduced.18 However, the microporous structure of activated carbon leads to the irreversible adsorption of some C60 and nearly all of the C70. The discovery of ordered mesoporous materials20-24 has provided new possibilities in the fields of adsorption and catalysis. The template synthesis of ordered mesoporous materials has received widespread attention recently because this technique allows the preparation of materials with controllable architecture.25 In 2000, to solve the irreversibility problem in fullerene adsorption, Piwonski et al.26 first reported the adsorption of pure C60 from toluene solution on ordered mesoporous silica material, MCM-41. Although the amount of C60 adsorbed on MCM-41 was much smaller than that adsorbed on AC,4 the adsorption process of C60 on MCM-41 was found to be completely reversible. This gave MCM-41 certain advantages over other stationary-phase materials. Therefore, we (19) Naoki, Komatsu.; Toshiyuki, Ohe.; Kazumi, Matsushige. Carbon 2004, 42, 163-167. (20) Beck, J. S.; Vartuli, J. C.; Roth, W. J.; Leonowicz, M. E.; Kresge, C. T.; Schmitt, K. D.; Chu, C. T. W.; Olson, D. H.; Sheppard, E. W.; McCullen, S. B.; Higgins, J. B.; Schlenker, J. C. J. Am. Chem. Soc. 1992, 114, 10834-10843. (21) Monnier, A.; Schu¨th, F.; Huo, Q.; Kumar, D.; Margolese, D.; Maxwell, R. S.; Stucky, G. D.; Krishnamurty, M.; Petroff, P.; Firouzi, A.; Janicke, M.; Chmelka, B. F. Science 1993, 261, 1299-1303. (22) Inagaki, S.; Fukushima, Y.; Kuroda, K. J. Chem. Soc., Chem. Commun. 1993, 8, 680-682. (23) Tanev, P. T.; Pinnavaia, T. J. Chem. Mater. 1996, 8, 2068-2079. (24) Jones, D. J.; Jime’nez-Jime’nez, J.; Jime’nez-Lo’pez, A.; Maireles-Torres, P.; Olivera-Pastor, P.; Rodry´’guez-Castello’n, E.; Rozie’re, J. Chem. Commun. 1997, 5, 431-432. Jones, D. J.; Aptel, G.; Brandhorst, M.; Jacquin, M.; Jime’nezJime’nez, J.; Jime’nez-Lo’pez, A.; Maireles-Torres, P.; Piwonski, I.; Rodry´’guezCastello’n, E.; Rozie’re, J.; Zajac, J. J. Mater. Chem. 2000, 10, 1957-1963. (25) Branton, P. J.; Hall, P. G.; Sing, K. S. W.; Reichert, H.; Schuth, F.; Unger, K. K. J. Chem. Soc., Faraday Trans. 1994, 90, 2965-2969. (26) Piwonski, I.; Zajac, J.; Jones, D. J.; Roziere, J.; Partyka, S.; Plaza, S. Langmuir 2000, 16, 9488-9492.

10.1021/la052615l CCC: $33.50 © 2006 American Chemical Society Published on Web 04/12/2006

4584 Langmuir, Vol. 22, No. 10, 2006

believe that an ordered mesoporous carbon, which has a welldefined mesoporous pore structure, a large surface area, and a high adsorption capacity, should be an ideal adsorbent to solve the problems in fullerene adsorption. In this study, an ordered mesoporous carbon (CMK-3) was synthesized, characterized, and first used for the adsorption of fullerenes. The adsorption of fullerenes on CMK-3 was studied for both single and binary systems. The desorption of fullerenes on CMK-3 was also investigated to study the reversibility. Various factors affecting the adsorption and desorption of fullerenes on CMK-3 were examined. Materials and Methods Synthesis of CMK-3. Siliceous material SBA-15 was synthesized by the sol-gel method. A triblock copolymer (Pluronic 123, pure, Aldrich) and an organic silica material (tetraethyl orthosilicate, i.e., TEOS, 98%, Aldrich) were employed as sources of template and silica, respectively. In a typical synthesis, 4 g of Pluronic 123 was first dissolved in 150 g of 1.6 M HCl to form a template solution. It was then stirred vigorously until a milky solution was observed, followed by adding 8.5 g of TEOS to the milky solution at 35 °C. The resulting solution was aged at 35 °C for 24 h and subsequently at 110 °C for another 24 h. Afterward, SBA-15 was obtained by calcination at 550 °C for 9 h in air. The template-free SBA-15 material was then used as a mold for the synthesis of mesoporous carbon. Sucrose and sulfuric acid were used as the carbon source and the dehydrating agent, respectively. Sucrose solution is obtained by dissolving 1.25 g of solid sucrose in 5 mL of water. Then, 0.14 g of 98% sulfuric acid was added to the sucrose solution under stirring. Finally, the acid-containing sucrose solution was impregnated with 1 g of the template-free SBA-15. The mixture was then put into an oven at 100 °C for 6 h and subsequently at 160 °C for another 6 h. The impregnation step was repeated once but with different amounts of the substances (0.8 g of sucrose, 0.09 g of H2SO4, and 5 mL of H2O). After the impregnation step, the dark-brown solid product, which was a composite of carbon and SBA-15, was carbonized at 1050 °C under vacuum for 6 h. The generated black powders (composites) were leached with a mixture of ethanol and 1 M sodium hydroxide solution to remove the silica and further recovered by filtration, washed with distilled water, and dried at 60 °C overnight to produce the ordered mesoporous carbon (CMK-3). Fullerenes. C60 (99.5%) and mixture of fullerenes (approximately 79% C60, 13% C70) were supplied by Frontier Carbon Corp., Japan. C70 (98+%) was obtained from Nano-C. Characterization. Low-angle X-ray diffraction patterns of samples were recorded with a powder X-ray diffraction system (X’pert model, Panalytical). The step width was 0.02° at an acquisition time of 8 s/step in the range of 2θ ) 0.85-5.0°. A TEM image was obtained using a JEOL JEM-2010F transmission electron microscope. The TEM image was taken from the thin edges of carbon particles mounted on a porous carbon grid. Nitrogen adsorption isotherms were measured with an ASAP2010 adsorption analyzer (Micromeritics) at liquid-nitrogen temperature. Prior to the measurements, all of the samples were degassed at a temperature of 200 °C for 6 h. The adsorption data in the relative pressure range from 0.04 to 0.2 were used to determine the BET surface area. The pore size distribution (PSD) was calculated by the BJH method from the desorption branch. The total pore volume was determined by the Gurvitsh rule,27 and the micropore volume was obtained from the Horvath-Kawazoe method.28 Measurement of C60 and C70 Concentrations. High-performance liquid chromatography (HPLC) was used to determine the concentrations of C60 and C70 in the solution. Different known concentrations of pure C60 and pure C70 solutions in toluene were prepared to calibrate the relationship between the peak area and the fullerene concentration, which was found to be linear. HPLC analysis was performed on a (27) Gurvitsh, L. J. Phys. Chem. Soc. Russ. 1915, 47, 805. (28) Horvath, G.; Kawazoe K. J. Chem. Eng. Jpn. 1983, 16, 470-475.

Wang et al. Hewlett-Packard I090 liquid chromatograph equipped with a YMCPack ODS-A column (4.6 × 150 mm2). The detection was performed with UV-visible light at 330 nm. Toluene/2-propanol (1:1 v/v) was used as the mobile phase, and the flow rate was set to 1 mL/min. Determination of Fullerene Adsorption Equilibrium Isotherm on Different Adsorbents. The time required for the adsorption of fullerene to reach equilibrium on different adsorbents was studied in a batch system. Because the adsorption equilibrium time is much longer for a binary system than for a single-component system, a mixture of C60 and C70 was used to determine the required equilibrium time. Once this equilibrium time is obtained, it is used to measure the adsorption equilibrium isotherms of pure C60 and pure C70 as well as their mixture. The adsorption process of mixed C60 and C70 from its solution in toluene (initial concentration of fullerene was 100 mg/L, weight ratio of C60/C70 ) 79:13) by different adsorbents at 25 °C was studied in a batch system. The four adsorbents examined were alumina, activated carbon mixed with silica gel (weight ratio 1:1), activated carbon, and ordered mesoporous carbon (CMK-3). The alumina was aluminum oxide 90 active neutral for column chromatography, 0.063-0.2 mm (70-230 mesh ASTM) supplied by Merck. The activated carbon was Norit Row 0.8 Supra supplied as a cylindrical extrudate but crushed into ∼0.1 mm particles before use, and the silica gel was silica gel 60, (0.04-0.063 mm) for column chromatography (230-400 mesh ASTM), also supplied by Merck. The weight of each adsorbent used was 25 mg. The adsorption solution volume was 20 mL. During the adsorption process, samples were drawn out (0.3 mL per sample) at different time intervals, and the fullerene concentrations in the samples were analyzed by HPLC. Adsorption Isotherms of Binary C60 and C70 on Different Adsorbents. Once the time required to reach equilibrium was determined (24 h), it was used to measure the adsorption equilibrium isotherms of fullerenes on CMK-3 and AC at 25 °C. A volume of 20 mL of different initial concentrations of fullerene in the toluene solutions was mixed with 25 mg of adsorbent and stirred for 24 h for equilibrium to be established. Adsorption of Pure C60 and Pure C70 on CMK-3. The adsorption equilibrium isotherms of pure C60 and pure C70 on CMK-3 at 25 °C were measured by changing the initial concentrations of pure C60 and pure C70 solutions. The weight of CMK-3 was 25 mg. The adsorption volume was 20 mL. After 24 h, adsorption equilibrium was reached in the system. Desorption of Pure C60 and Pure C70 from CMK-3 and AC. Twenty-five milligrams of CMK-3 or AC was placed into 200 mL of a solution of 100 mg/L pure C60 or C70 at 25 °C for 24 h for equilibrium to be established. Then the solution was filtered, and the solid was dried under vacuum at 60 °C for 10 h to remove the toluene. The recovered solid was then placed in 200 mL of fresh toluene to start the desorption of pure C60 or pure C70. Effect of Solvent Volume on the Desorption of Pure C60 and Pure C70 from CMK-3. Twenty-five milligrams of dried CMK-3 presaturated with pure C60 or C70 was placed in different toluene volumes of 50, 150, 250, 450, 650, and 1000 mL for desorption to proceed. The desorption time for each desorption volume was 12 h. Effect of Temperature on the Desorption of Pure C60 and Pure C70 from CMK-3. Twenty-five milligrams of dried CMK-3 presaturated with pure C60 or C70 was placed in 250 mL of fresh toluene. Again the desorption time was 12 h. Desorption was carried out for different temperatures. The recovered CMK-3 was placed into another 250 mL of fresh toluene solution to start the second desorption cycle. This was repeated for four desorption cycles.

Results and Discussion Characterization of SBA-15, CMK-3, and AC. The structures of the SBA-15 template and the corresponding CMK-3 were studied using a low-angle XRD system of Cu KR. Their XRD patterns are shown in Figure 1. The well-resolved XRD peaks of SBA-15 that can be assigned to (100), (110), and (200) diffractions indicate that it has an ordered structure with 2-D hexagonal symmetry. Therefore, CMK-3 should have a hexagonal

Mesoporous Carbon for the Adsorption of Fullerenes

Figure 1. XRD spectra of SBA-15 and CMK-3.

Langmuir, Vol. 22, No. 10, 2006 4585

Figure 3. Nitrogen sorption isotherms of SBA-15 and CMK-3. Table 1. Texture Parameters of SBA-15, the Corresponding CMK-3, and AC sample SBA-15 ordered mesoporous carbon (CMK-3) Norit Row 0.8 Supra (AC)

Vta Vmib mean pore size SBET (m2 g-1) (cm3 g-1) (cm3 g-1) (diameter, nm) 815 1366

1.02 1.14

0.06 0.12

6.5 3.5

911

1.18

0.58

1.16

a Vt: total pore volume calculated at p/p0 ) 0.99. b Vmi: microporous volume (diameter